This adds max1117/max1118/max1119 8-bit, dual-channel ADC driver.
This new driver uses the zero length spi_transfers with the cs_change
flag set and/or the non-zero delay_usecs.
1. The zero length transfer with the spi_transfer.cs_change set is
required in order to select CH1. The chip select line must be brought
high and low again without transfer.
2. The zero length transfer with the spi_transfer.delay_usecs > 0 is
required for waiting the conversion to be complete. The conversion
begins with the falling edge of the chip select. During the conversion
process, SCLK is ignored.
These two usages are unusual. But the spi controller drivers that use
a default implementation of transfer_one_message() are likely to work.
(I've tested this adc driver with spi-omap2-mcspi and spi-xilinx)
On the other hand, some spi controller drivers that have their own
transfer_one_message() may not work. But at least for the zero length
transfer with delay_usecs > 0, I'm proposing a new testcase for the
spi-loopback-test that can test whether the delay_usecs setting has
taken effect.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The Qualcomm PM8xxx PMICs contain a simpler ADC than its
successors (already in the kernel as qcom-spmi-vadc.c):
the HK/XO ADC (Housekeeping/Chrystal oscillator ADC).
As far as I can understand this is equal to the PMICs
using SSBI transport and encompass PM8018, PM8038,
PM8058, and PM8921, so this is shortly named PM8xxx.
This ADC monitors a bunch of on-board voltages and the die
temperature of the PMIC itself, but it can also be routed
to convert a few external MPPs (multi-purpose pins). On
the APQ8060 DragonBoard this feature is used to let this
ADC convert an analog ALS (Ambient Light Sensor) voltage
signal from a Capella CM3605 ALS into a LUX value.
Developed and tested with APQ8060 DragonBoard based on
Ivan's driver and Rama Krishna's patches. The SPMI VADC
driver is quite different, but share enough minor
functionality that I have split out to the common file
in a previous patch.
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Cc: Ivan T. Ivanov <iivanov.xz@gmail.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Rama Krishna Phani A <rphani@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The SPMI VADC and the earlier XOADC share a subset of
common code, so to be able to use the same code in both
drivers, we break out a separate file with the common code,
prefix exported functions that are no longer static with
qcom_* and bake an object qcom-spmi-vadc.o that contains both
files: qcom-vadc-common.o and qcom-spmi-vadc-core.o.
As we need to follow the procedure for making a kernel module
or compiled in object from several files, but still want to
produce the same module name, rename the qcom-spmi-vadc.c
file to qcom-spmi-vadc-core.c so we can bake the two objects
into qcom-spmi-vadc.o
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Cc: Ivan T. Ivanov <iivanov.xz@gmail.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Rama Krishna Phani A <rphani@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds support for the Allwinner A33 thermal sensor.
Unlike the A10, A13 and A31, the Allwinner A33 only has one channel
which is dedicated to the thermal sensor. Moreover, its thermal sensor
does not generate interruptions, thus we only need to directly read the
register storing the temperature value.
The MFD used by the A10, A13 and A31, was created to avoid breaking the
DT binding, but since the nodes for the ADC weren't there for the A33,
it is not needed.
Though the A33 does not have an internal ADC, it has a thermal sensor
which shares the same registers with GPADC of the already supported SoCs
and almost the same bits, for the same purpose (thermal sensor).
The thermal sensor behaves exactly the same (except the presence of
interrupts or not) on the different SoCs.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
With CONFIG_THERMAL=m and CONFIG_SUN4I_GPADC=y, we get a link error
from calling devm_thermal_zone_of_sensor_register:
drivers/iio/built-in.o: In function `sun4i_gpadc_probe':
:(.text+0x1c284): undefined reference to `devm_thermal_zone_of_sensor_register'
This adds a Kconfig dependency to ensure we can only have the ADC
driver as built-in when this function is also built-in, or when
we see the empty stub implementation. When the thermal code is
a module, we can still build the adc driver as a module, too.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: d1caa99055 ("iio: adc: add support for Allwinner SoCs ADC")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds support for the Analog Devices / Linear Technology
LTC2497 ADCs. The LTC2497 is a 16-channel (eight differential),
16-bit, high precision, delta-sigma ADC with an automatic, differential,
input current cancellation front end and a 2-wire, I2C interface.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Aspeed BMC SoCs include a 16 channel, 10-bit ADC. Low and high threshold
interrupts are supported by the hardware but are not currently implemented.
Signed-off-by: Rick Altherr <raltherr@google.com>
Tested-by: Xo Wang <xow@google.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
On Motorola phones like droid 4 there is a custom CPCAP PMIC. This PMIC
has ADCs that are used for battery charging and USB PHY VBUS and ID pin
detection.
Unfortunately the only documentation for this ADC seems to be the
Motorola mapphone Linux kernel tree. I have tested that reading raw and
scaled values works, but I have not used the timed sampling that the ADC
seems to support.
Let's add a minimal support for it so we can eventually provide IIO
channels for the related battery charging and USB PHY drivers.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
PC/104 drivers should be hidden on machines which do not support PC/104
devices. This patch adds the PC104 Kconfig option as a dependency for
the relevant PC/104 device driver Kconfig options.
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The Allwinner SoCs all have an ADC that can also act as a touchscreen
controller and a thermal sensor. This patch adds the ADC driver which is
based on the MFD for the same SoCs ADC.
This also registers the thermal adc channel in the iio map array so
iio_hwmon could use it without modifying the Device Tree. This registers
the driver in the thermal framework.
The thermal sensor requires the IP to be in touchscreen mode to return
correct values. Therefore, if the user is continuously reading the ADC
channel(s), the thermal framework in which the thermal sensor is
registered will switch the IP in touchscreen mode to get a temperature
value and requires a delay of 100ms (because of the mode switching),
then the ADC will switch back to ADC mode and requires also a delay of
100ms. If the ADC readings are critical to user and the SoC temperature
is not, this driver is capable of not registering the thermal sensor in
the thermal framework and thus, "quicken" the ADC readings.
This driver probes on three different platform_device_id to take into
account slight differences (registers bit and temperature computation)
between Allwinner SoCs ADCs.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
There are a few more little cleanups that could be done on this driver, but
I don't think any are sufficient to justify not moving it out of staging.
It's a very simple driver (presumably for a simple part) so not much that can
go wrong. I think it was only ever in staging because that's where IIO was
as a whole at the time and then we forgot about it!
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: Roland Stigge <stigge@antcom.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
There are some unanswered questions due to disagreements between the code
and various datasheets (including between different datasheets for the same
part).
I don't think that is necessarily a reason to keep it in staging however.
I'm partly posting this patch inorder to reignite debate and with a bit
of luck find someone who has one of these to test!
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add DMA optional support to STM32 ADC, as there is a limited number DMA
channels (request lines) that can be assigned to ADC. This way, driver
may fall back using interrupts when all DMA channels are in use for
other IPs.
Use dma cyclic mode with two periods. Allow to tune period length by
using watermark. Coherent memory is used for dma (max buffer size is
fixed to PAGE_SIZE).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
STM32 ADC has external timer trigger sources. Use stm32 timer triggers
API (e.g. is_stm32_timer_trigger()) with local ADC lookup table to
validate a trigger can be used.
This also provides correct trigger selection value (e.g. extsel).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
STM32 ADC conversions can be launched using hardware triggers.
It can be used to start conversion sequences (group of channels).
Selected channels are select via sequence registers.
Trigger source is selected via 'extsel' (external trigger mux).
Trigger polarity is set to rising edge by default.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds support for the SAR (Successive Approximation Register) ADC
on the Amlogic Meson SoCs.
The code is based on the public S805 (Meson8b) and S905 (GXBB)
datasheets (see [0] and [1]), as well as by reading (various versions
of) the vendor driver and by inspecting the registers on the vendor
kernels of my testing-hardware.
Currently the GXBB, GXL and GXM SoCs are supported. GXBB hardware has
10-bit ADC resolution, while GXL and GXM have 12-bit ADC resolution.
The code was written to support older SoCs (Meson8 and Meson8b) as well,
but due to lack of actual testing-hardware no of_device_id was added for
these.
Two "features" from the vendor driver are currently missing:
- the vendor driver uses channel #7 for calibration (this improves the
accuracy of the results - in my tests the results were less than 3%
off without calibration compared to the vendor driver). Adding support
for this should be easy, but is not required for most applications.
- channel #6 is connected to the SoCs internal temperature sensor.
Adding support for this is probably not so easy since (based on the
u-boot sources) most SoC versions are using different registers and
algorithms for the conversion from "ADC value" to temperature.
Supported by the hardware but currently not supported by the driver:
- reading multiple channels at the same time (the hardware has a FIFO
buffer which stores multiple results)
- continuous sampling (this would require a way to enable this
individually because otherwise the ADC would be drawing power
constantly)
- interrupt support (similar to the vendor driver this new driver is
polling the results. It is unclear if the IRQ-mode is supported on
older (Meson6 or Meson8) hardware as well or if there are any errata)
[0]
http://dn.odroid.com/S805/Datasheet/S805_Datasheet%20V0.8%2020150126.pdf
[1] http://dn.odroid.com/S905/DataSheet/S905_Public_Datasheet_V1.1.4.pdf
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add IIO driver for the Renesas RCar GyroADC block. This block is a
simple 4/8-channel ADC which samples 12/15/24 bits of data every
cycle from all channels.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-renesas-soc@vger.kernel.org
Cc: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
New device support:
* lsm6dsx imu
- new driver and bindings.
* max11100 adc
- new driver and bindings.
* tlc4541
- new driver
* tmp007 thermopile
- new driver.
Core
* in kernel interfaces
- pass through raw values if no scaling provided and a processed value is
requested.
* trigger
- close a race condition in acquiring trigger reference.
- constify device_type structures.
- rework the viio_trigger_alloc function to be much neater and easier to
read.
- free trigger resources correctly on some error paths. Avoids putting a
module we don't have.
Documentation
* ABI
- specify a unit for proximity measurements.
Cleanups and features
* ads1015
- constify iio_info structure.
* ads7950 cleanups following merge in previous pull
- Add device tree bindings
- Drop the ti prefix from the module name in common with other drivers.
- Change regulator name to vref to match datasheet and other drivers.
* ak8974
- remove a redundant zero timeout check.
* bmi160
- use variable names for sizeof instead of types.
* cm3605
- mark PM functions as __maybe_unused to avoid a build warning.
* isl29028 (on it's way towards moving out of staging).
- alignment fixes and newline improvements.
- combine proxim_get and read_proxim for simpler code.
- drop unused ISL29028_DEV_ATTR macro
- move some error logging into functions to cut out repitition.
- make error messages more consistent.
- tidy up some brackets.
- drop the enable flag that nothing uses.
- only set proximity rate and ALS scale when relevant channel type is enabled.
- runtime pm support.
* lsm6dsx
- fix wrong values for gyro sensitivitiy.
* mag3110
- claim direct mode during sysfs reads to avoid a race condition.
* max1363
- export OF device table IDs as module aliases.
* max30100
- use msleep for long uncritical delays.
* mcp4531
- export OF device table as module aliases.
* ms5611
- claim direct mode during sysfs reads to avoid a race condition.
* opt3001
- export OF device table as module aliases.
* sx9500
- claim direct mode during oversampling changes to avoid a race condition.
-----BEGIN PGP SIGNATURE-----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=Wvje
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.11b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into work-next
Jonathan writes:
Second round of IIO new device support, cleanups and features for the 4.11 cycle
New device support:
* lsm6dsx imu
- new driver and bindings.
* max11100 adc
- new driver and bindings.
* tlc4541
- new driver
* tmp007 thermopile
- new driver.
Core
* in kernel interfaces
- pass through raw values if no scaling provided and a processed value is
requested.
* trigger
- close a race condition in acquiring trigger reference.
- constify device_type structures.
- rework the viio_trigger_alloc function to be much neater and easier to
read.
- free trigger resources correctly on some error paths. Avoids putting a
module we don't have.
Documentation
* ABI
- specify a unit for proximity measurements.
Cleanups and features
* ads1015
- constify iio_info structure.
* ads7950 cleanups following merge in previous pull
- Add device tree bindings
- Drop the ti prefix from the module name in common with other drivers.
- Change regulator name to vref to match datasheet and other drivers.
* ak8974
- remove a redundant zero timeout check.
* bmi160
- use variable names for sizeof instead of types.
* cm3605
- mark PM functions as __maybe_unused to avoid a build warning.
* isl29028 (on it's way towards moving out of staging).
- alignment fixes and newline improvements.
- combine proxim_get and read_proxim for simpler code.
- drop unused ISL29028_DEV_ATTR macro
- move some error logging into functions to cut out repitition.
- make error messages more consistent.
- tidy up some brackets.
- drop the enable flag that nothing uses.
- only set proximity rate and ALS scale when relevant channel type is enabled.
- runtime pm support.
* lsm6dsx
- fix wrong values for gyro sensitivitiy.
* mag3110
- claim direct mode during sysfs reads to avoid a race condition.
* max1363
- export OF device table IDs as module aliases.
* max30100
- use msleep for long uncritical delays.
* mcp4531
- export OF device table as module aliases.
* ms5611
- claim direct mode during sysfs reads to avoid a race condition.
* opt3001
- export OF device table as module aliases.
* sx9500
- claim direct mode during oversampling changes to avoid a race condition.
This adds TI's tlc4541 16-bit ADC driver. Which is a single channel
ADC. Supports raw and trigger buffer access.
Also supports the tlc3541 14-bit device, which has not been tested.
Implementation of the tlc3541 is fairly straight forward thou.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
It's shaping to be another fairly busy cycle. Lots more on the way!
New device support
* ads7950
- new driver supporting ads7950, ads7951, ads7952, ads7953, ads7954,
ads7955, ads7956, ads7957, ads7958, ads7959, ads7960, and ads7961 ADCs.
* cm3605
- New driver for this light sensor and proximity sensor which is an
analog part with some additional digital controls.
* hx711
- New driver.
Core new stuff
* Gravity sensor type. This is a processed datastream in which the device
will try to work out which way is down.
* Split the buffer.h file into two parts. One provides the interface to 'use'
a buffer, the second provides the internals of the buffer functionality as
needed by implementations of buffers.
- Move documentation inline so as to allow use of private: tag when
generating documentation.
- Add some utility functions for the few things that are directly done
with the buffers.
- Stop exporting functions that no-one uses outside of the core code.
- Push docs down by the code in the c file where they should have always
been.
- Fix typo in kernel-doc for buffer.
- push down some includes that were previously happening implicitly.
- stop enabling the timestamp of the dummy device.
Features and cleanups
* ad5592r
- ACPI support
* ad5593r
-ACPI support.
* ad5933
- Fix a false comment about size of a particular register.
* ad7150
- replace S_IRUGO | S_IWUSR with 0644. I'm not that keen on these patches
in general, but as it was nicely presented I took this one anyway. As a
general rule will only take these as part of a larger driver cleanup.
- don't eat an error but rather reutnr it in the write_event_config callback.
* ad7606
- replace non standard range attibute with _scale
* ade7753
- use usleep_range for short sleeps
* ade7754
- use usleep_range for short sleeps
* ade7758
- use usleep_range for short sleeps
* ade7759
- use usleep_range for short sleeps
* ade7854
- use usleep_range for short sleeps
* adis16201
- fix description
* adis16203
- fix description
- fix copyright year
* adis16209
- fix description
* adt7316
- Add braces to arms of if else statement (for consistency)
- Alignment fixes.
* axp288
- Fix up an issue with accidental overwrites of data.
* bmi160
- add deivce tables for i2c and spi to support correctly identifying the
full dt name (including manufacturer).
- device tree binding.
* bmp280
- use usleep_range for short sleeps.
* cm3232
- return error from cm3232_reg_init rather than eating it if the last write
fails.
* dummy driver
- remove a semicolor found at end of a function defintition.
* exynos-adc
- use usleep_range for short sleeps.
* hid-sensor (accel)
- Add timestamp support. The hardware can provide timestamps so lets support
them. If not fall back to timestamps estimated in kernel.
* hid-sensor (light)
- Add a duplicate ID for the light channels so as to keep existing interface
whilst also using the more standard IIO interface.
* hts221
- acpi probing
* imx25-gcq
- Add a macro call to allow this driver to be automatically loaded.
* isl29028
- reorganise code to avoid deep nesting of if statements.
- move chip test and default regs into a function suitable or sharing with
power management code.
- tidy up some code alignment.
* lidar-lite-v3
- introduce compatible strings that make it clear Garmin have consideral
friends.
* mma8452
- avoid returning signed value when unsigned is appropriate
* spmi-vadc
- Update function for generic voltage conversion to take into account that
different channels on this device should be handled differently.
- Rework code to allow per channel voltage scaling and support the standard
options for this hardware.
- Fixup three minor issues with the above patches for this part. These all
effect test builds rather than the native builds for the part, but good to
clean them up anyway.
* st_sensors
- support device matching from the ACPI DST tables.
- acpi based probing for accelerometers
- acpi based probing for pressure sensors
- Allow pressure sensors to read negative values.
- Export sampling frequency for lps25h and lps331ap.
- Add support for the old DT bindings from the period when these deivces
were often supported through windows.
Docs fixup:
* typo in sysfs-bus-iio
-----BEGIN PGP SIGNATURE-----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=yjUA
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.11a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of new device support, features and cleanups for IIO in the 4.11 cycle.
It's shaping to be another fairly busy cycle. Lots more on the way!
New device support
* ads7950
- new driver supporting ads7950, ads7951, ads7952, ads7953, ads7954,
ads7955, ads7956, ads7957, ads7958, ads7959, ads7960, and ads7961 ADCs.
* cm3605
- New driver for this light sensor and proximity sensor which is an
analog part with some additional digital controls.
* hx711
- New driver.
Core new stuff
* Gravity sensor type. This is a processed datastream in which the device
will try to work out which way is down.
* Split the buffer.h file into two parts. One provides the interface to 'use'
a buffer, the second provides the internals of the buffer functionality as
needed by implementations of buffers.
- Move documentation inline so as to allow use of private: tag when
generating documentation.
- Add some utility functions for the few things that are directly done
with the buffers.
- Stop exporting functions that no-one uses outside of the core code.
- Push docs down by the code in the c file where they should have always
been.
- Fix typo in kernel-doc for buffer.
- push down some includes that were previously happening implicitly.
- stop enabling the timestamp of the dummy device.
Features and cleanups
* ad5592r
- ACPI support
* ad5593r
-ACPI support.
* ad5933
- Fix a false comment about size of a particular register.
* ad7150
- replace S_IRUGO | S_IWUSR with 0644. I'm not that keen on these patches
in general, but as it was nicely presented I took this one anyway. As a
general rule will only take these as part of a larger driver cleanup.
- don't eat an error but rather reutnr it in the write_event_config callback.
* ad7606
- replace non standard range attibute with _scale
* ade7753
- use usleep_range for short sleeps
* ade7754
- use usleep_range for short sleeps
* ade7758
- use usleep_range for short sleeps
* ade7759
- use usleep_range for short sleeps
* ade7854
- use usleep_range for short sleeps
* adis16201
- fix description
* adis16203
- fix description
- fix copyright year
* adis16209
- fix description
* adt7316
- Add braces to arms of if else statement (for consistency)
- Alignment fixes.
* axp288
- Fix up an issue with accidental overwrites of data.
* bmi160
- add deivce tables for i2c and spi to support correctly identifying the
full dt name (including manufacturer).
- device tree binding.
* bmp280
- use usleep_range for short sleeps.
* cm3232
- return error from cm3232_reg_init rather than eating it if the last write
fails.
* dummy driver
- remove a semicolor found at end of a function defintition.
* exynos-adc
- use usleep_range for short sleeps.
* hid-sensor (accel)
- Add timestamp support. The hardware can provide timestamps so lets support
them. If not fall back to timestamps estimated in kernel.
* hid-sensor (light)
- Add a duplicate ID for the light channels so as to keep existing interface
whilst also using the more standard IIO interface.
* hts221
- acpi probing
* imx25-gcq
- Add a macro call to allow this driver to be automatically loaded.
* isl29028
- reorganise code to avoid deep nesting of if statements.
- move chip test and default regs into a function suitable or sharing with
power management code.
- tidy up some code alignment.
* lidar-lite-v3
- introduce compatible strings that make it clear Garmin have consideral
friends.
* mma8452
- avoid returning signed value when unsigned is appropriate
* spmi-vadc
- Update function for generic voltage conversion to take into account that
different channels on this device should be handled differently.
- Rework code to allow per channel voltage scaling and support the standard
options for this hardware.
- Fixup three minor issues with the above patches for this part. These all
effect test builds rather than the native builds for the part, but good to
clean them up anyway.
* st_sensors
- support device matching from the ACPI DST tables.
- acpi based probing for accelerometers
- acpi based probing for pressure sensors
- Allow pressure sensors to read negative values.
- Export sampling frequency for lps25h and lps331ap.
- Add support for the old DT bindings from the period when these deivces
were often supported through windows.
Docs fixup:
* typo in sysfs-bus-iio
This is the IIO driver for AVIA HX711 ADC which is mostly used in weighting
cells.
The protocol is quite simple and using GPIOs:
One GPIO is used as clock (SCK) while another GPIO is read (DOUT)
The raw value read from the chip is delivered.
To get a weight one needs to subtract the zero offset and scale it.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds a new driver for the TI ADS7950 family of ADC chips. These
communicate using SPI and come in 8/10/12-bit and 4/8/12/16 channel
varieties.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds support for STMicroelectronics STM32 MCU's analog to
digital converter.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add core driver for STMicroelectronics STM32 ADC (Analog to Digital
Converter). STM32 ADC can be composed of up to 3 ADCs with shared
resources like clock prescaler, common interrupt line and analog
reference voltage.
This core driver basically manages shared resources.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The DAC is used to find the peak level of an alternating voltage input
signal by a binary search using the output of a comparator wired to
an interrupt pin. Like so:
_
| \
input +------>-------|+ \
| \
.-------. | }---.
| | | / |
| dac|-->--|- / |
| | |_/ |
| | |
| | |
| irq|------<-------'
| |
'-------'
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This resolves a merge issue with
drivers/staging/iio/accel/sca3000_core.c and we want the fixes all in
here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds triggered buffer support for the ti-adc0832 driver. Tested with
ADC0831 and ADC0832 by using SYSFS trigger.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Commit 08e05d1fce ("ti-adc081c: Initial triggered buffer support") added
triggered buffer support but that also requires CONFIG_IIO_TRIGGERED_BUFFER,
otherwise we get errors from linker such as:
drivers/built-in.o: In function `adc081c_remove':
drivers/iio/adc/ti-adc081c.c:225: undefined reference to `iio_triggered_buffer_cleanup'
Fix these by explicitly selecting both CONFIG_IIO_TRIGGERED_BUFFER and
CONFIG_IIO_BUFFER in Kconfig for the driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for the AD7766, AD7766-1, AD7766-2, AD7767, AD7767-1, AD7767-2
Analog to Digital converters. It's a family of single channel 24-bit SAR
ADCs. They are all digital interface compatible and the main difference is
the internal decimation rate and analog performance. For communication with
the host processor a SPI interface is used.
In addition the part has a data ready pin that is pulsed for one MCLK cycle
when a conversion has completed and can be used as a IIO trigger.
Datasheets:
http://www.analog.com/media/en/technical-documentation/data-sheets/AD7766.pdfhttp://www.analog.com/media/en/technical-documentation/data-sheets/AD7767.pdf
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
New device support
* ad8801 dac
- new driver supporting ad8801 and ad8803 DACs.
* adc12138
- new driver supporting TI adc12130/adc12132 and adc12138 ADCs.
* ltc2485 adc
- new driver
* mxc6255
- add support for the mxc6225 part name and fixup the ID check so it works.
* vz89x VOC sensor
- add support for the vz89te part which drops the voc_short channel and adds
CRCs compared to other supported parts.
New features
* core
- immutable triggers. These effectively grant exclusive control over a
trigger. The typical usecase is a device representing an analog part
(perhaps a MUX) that needs to control the sampling of a downstream
ADC.
- resource managed trigger registration and triggered_buffer_init.
- iio_push_event now protected against case of the event interface
registration not having yet occured. Only matters if an interrupt
can occur during this window - might happen on shared interrupt lines.
- helper to let a driver query if the trigger it is using is provided by
itself (using the convention of both device and trigger having the same
parent).
* tools
- iio-utils. Used channel modifier scaling in preference to generic scaling
when both exist.
* at91-adc
- Add support for touchscreen switches closure time needed by some newer
parts.
* stx104
- support the ADC channels on this ADC/DAC board. As these are the primary
feature of the board also move the driver to the iio/adc directory.
* sx9500
- device tree bindings.
Cleanups / Fixes
* ad5755
- fix an off-by-one on devnr limit check (introduced earlier this cycle)
* ad7266
- drop NULL check on devm_regulator_get_optional as it can't return NULL.
* ak8974
- avoid an unused functional warning due to rework in PM core code.
- remove .owner field setting as done by i2c_core.
* ina2xx
- clear out a left over debug field from chip global data.
* hid-sensors
- avoid an unused functional warning due to rework in PM core code.
* maxim-thermocouple
- fix non static symbol warnings.
* ms5611
- fetch and enable regulators unconditionally when they aren't optional.
* sca3000
- whitespace cleanup.
* st_sensors
- fetch and enable regulators unconditionally rather than having them
supported as optional regulators (missunderstanding on my part amongst
others a while back)
- followup to previous patch fixes error checking on the regulators.
- mark symbols static where possible.
- use the 'is it my trigger' help function. This prevents the odd case
of another device triggering from the st-sensors trigger whilst the
st-sensors trigger is itself not using it but rather using say an hrtimer.
* ti-ads1015
- add missing of_node_put.
* vz89x
- rework to all support of new devices.
- prevent reading of a corrupted buffer.
- fixup a return value of 0/1 in a bool returning function.
Address updates
- Vlad Dogaru email address change.
-----BEGIN PGP SIGNATURE-----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=V1xL
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.9b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of iio new device support, features and cleanups for the 4.9 cycle.
New device support
* ad8801 dac
- new driver supporting ad8801 and ad8803 DACs.
* adc12138
- new driver supporting TI adc12130/adc12132 and adc12138 ADCs.
* ltc2485 adc
- new driver
* mxc6255
- add support for the mxc6225 part name and fixup the ID check so it works.
* vz89x VOC sensor
- add support for the vz89te part which drops the voc_short channel and adds
CRCs compared to other supported parts.
New features
* core
- immutable triggers. These effectively grant exclusive control over a
trigger. The typical usecase is a device representing an analog part
(perhaps a MUX) that needs to control the sampling of a downstream
ADC.
- resource managed trigger registration and triggered_buffer_init.
- iio_push_event now protected against case of the event interface
registration not having yet occured. Only matters if an interrupt
can occur during this window - might happen on shared interrupt lines.
- helper to let a driver query if the trigger it is using is provided by
itself (using the convention of both device and trigger having the same
parent).
* tools
- iio-utils. Used channel modifier scaling in preference to generic scaling
when both exist.
* at91-adc
- Add support for touchscreen switches closure time needed by some newer
parts.
* stx104
- support the ADC channels on this ADC/DAC board. As these are the primary
feature of the board also move the driver to the iio/adc directory.
* sx9500
- device tree bindings.
Cleanups / Fixes
* ad5755
- fix an off-by-one on devnr limit check (introduced earlier this cycle)
* ad7266
- drop NULL check on devm_regulator_get_optional as it can't return NULL.
* ak8974
- avoid an unused functional warning due to rework in PM core code.
- remove .owner field setting as done by i2c_core.
* ina2xx
- clear out a left over debug field from chip global data.
* hid-sensors
- avoid an unused functional warning due to rework in PM core code.
* maxim-thermocouple
- fix non static symbol warnings.
* ms5611
- fetch and enable regulators unconditionally when they aren't optional.
* sca3000
- whitespace cleanup.
* st_sensors
- fetch and enable regulators unconditionally rather than having them
supported as optional regulators (missunderstanding on my part amongst
others a while back)
- followup to previous patch fixes error checking on the regulators.
- mark symbols static where possible.
- use the 'is it my trigger' help function. This prevents the odd case
of another device triggering from the st-sensors trigger whilst the
st-sensors trigger is itself not using it but rather using say an hrtimer.
* ti-ads1015
- add missing of_node_put.
* vz89x
- rework to all support of new devices.
- prevent reading of a corrupted buffer.
- fixup a return value of 0/1 in a bool returning function.
Address updates
- Vlad Dogaru email address change.
The Apex Embedded Systems STX104 features 16 channels of single-ended (8
channels of true differential) 16-bit analog input. Differential input
configuration may be selected via a physical jumper on the device.
Similarly, input polarity (unipolar/bipolar) is configured via a
physical jumper on the device.
Input gain selection is available to the user via software, thus
allowing eight possible input ranges: +-10V, +-5V, +-2.5V, +-1.25V,
0 to 10V, 0 to 5V, 0 to 2.5V, and 0 to 1.25V. Four input gain
configurations are supported: x1, x2, x4, and x8.
This ADC resolution is 16-bits (1/65536 of full scale). Analog input
samples are taken on software trigger; neither FIFO sampling nor
interrupt triggering is supported by this driver.
The Apex Embedded Systems STX104 is primarily an analog-to-digital
converter device. The STX104 IIO driver was initially placed in the DAC
directory because only the DAC portion of the STX104 was supported at
the time. Now that ADC support has been added to the STX104 IIO driver,
the driver should be moved to the more appropriate ADC directory.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds Texas Instruments' ADC12130/ADC12132/ADC12138 12-bit plus
sign ADC driver. I have tested with the ADC12138. The ADC12130 and
ADC12132 are not tested but these are similar to ADC12138 except that
the mode programming instruction is a bit different.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Adds basic support for the LTC2485 ADC - a delta-sigma analog-to-digital
converter with an I2C interface that operates in single shot conversion
mode.
The driver supports an on board 5V reference and the power-on default
configuration which rejects both 50hz & 60hz line frequencies and
operates in 1x speed mode.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
SARADC controller needs to be reset before programming it, otherwise
it will not function properly.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-iio@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Tested-by: Guenter Roeck <linux@roeck-us.net>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add Mediatek auxadc driver based on iio.
It will register a device in iio and support iio.
So thermal can read auxadc channel to sample data by iio device.
It is tested successfully on mt2701 platform.
Mt8173 and mt6577 platforms are not tested.
But the expectation is compatible.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for Texas Instruments ADC141S626, and ADC161S626 chips.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds basic driver implementation for Broadcom's
static adc controller used in iProc SoC's family.
Signed-off-by: Raveendra Padasalagi <raveendra.padasalagi@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
New core support
* UV light modifier (for intensity)
* UV light index channel type.
New device support
* hp206c barometer and altimeter
- new driver.
* mcp4131 potentiometer
- new driver supporting lots of parts from Microchip.
* mma8452
- FXLS8471Q support
- NXP LPC18XX SOC ADC
- new driver.
- NXP LPC18XX SOC DAC
- new driver.
- rockchip_saradc
- support rk3399
* st accel
- h3lis331dl support
Staging driver removals
* adis16204
- obsolete part making it hard to get parts to test the driver in order
to clean it up.
* adis16220
- obsolete part making it hard to get the parts test the driver in order
to clean it up.
Features
* core
- convenience functions to claim / release direct access to the device.
Makes more consistent handling of this corner easier. Used in ad7192 driver.
* ak8975
- power regulator support.
* at91-sama5d2
- differential channel support.
* mma8452
- runtime pm support
- drop device specific autosleep and use the runtime pm one instead.
* ms5611
- DT bindings
- oversampling ratio support
Cleanups and minor fixes
* MAINTAINERS
- Peter got married - hence name change!
* Documentation
- Fix a typo in in_proximity_raw description.
- Add some missing docs for iio_buffer_access_funcs.
* Tools
- update iio_event_monitor names to match new stuff.
- make generic_buffer look for triggers ending in -trigger as we let these in
for a number of drivers a long time back and now it is a fairly common
option.
Drivers
* staging wide
- convert bare unsigned usage to unsigned int to comply with coding style.
* non staging wide:
- since boiler plate gpio handling of interrupts has been moved into the
ACPI core we don't need to include gpio/consumer.h in a load of drivers so
drop it.
* ad7606
- fix an endian casting sparse warning.
* ak8975
- fix a possible unitialized warning from gcc.
- drop and unused field left over from earlier cleanups
- fix a missing regulator_disable on exit.
* at91-sama5d2
- typo and indentation
- missing IOMEM dependency.
- cleanup mode register usage by avoidling erasing whole thing when changing
the sampling frequency.
* bmc150
- use the core demux and available_scan_masks to simplify buffer handling
- optimize the transfers in the trigger handler now we have a magic function
to emulate bulk reads (under circumstances met here). This matters with some
rather dumb i2c adapters in particular.
- use a single regmap_conf for all bus types as they were all the same.
* bmg160
- use the core demux and available_scan_masks to simplify the buffer handling
- optimize the transfers in the trigger handler now we have a magic funciton
to emulate bulk rads (under circumstances met here).
- drop gpio interrupt probing from the driver (ACPI) as now handled by the
ACPI core.
* ina2xx-adc
- update the CALIB register when RShunt changes.
- fix scale for VShunt - in reality this error canceled out when used.
* isl29028
- use regmap to retrieve the struct device instead of carrying a second
copy of it around.
* kxcjk-1013
- use core demux
- optimize i2c transfers in the trigger handler.
* mcp4531
- refactor to use a pointer to access model parameters instead of indexing
into the array each time.
* mma8452
- style fixes
- avoid swtiching to active whenever the config changes
- add missin i2c_device_id for mma8451
* mpu6050
- fix possible NULL dereference.
- fix the name / chip_id used when ACPI used (otherwise reports as NULL).
* ms5611
- fix a missing regulator_disable that left the regulator on during removal.
* mxc4005
- drop gpio interrupt handling for ACPI case from driver as the core now
handles this case.
* st-sensors
- note that there are only ever a maximum of 3 axis on current st-sensors
so just allocate a fixed sized buffer big enough for that.
* tpl0102
- change the i2c_check_functionality condition to bring it inline with other
IIO users as EOPNOTSUPP.
* tsl2563
- replace deprecated flush_scheduled_work
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=SgQo
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.7a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of IIO new device support, features and cleanups for the 4.7 cycle.
New core support
* UV light modifier (for intensity)
* UV light index channel type.
New device support
* hp206c barometer and altimeter
- new driver.
* mcp4131 potentiometer
- new driver supporting lots of parts from Microchip.
* mma8452
- FXLS8471Q support
- NXP LPC18XX SOC ADC
- new driver.
- NXP LPC18XX SOC DAC
- new driver.
- rockchip_saradc
- support rk3399
* st accel
- h3lis331dl support
Staging driver removals
* adis16204
- obsolete part making it hard to get parts to test the driver in order
to clean it up.
* adis16220
- obsolete part making it hard to get the parts test the driver in order
to clean it up.
Features
* core
- convenience functions to claim / release direct access to the device.
Makes more consistent handling of this corner easier. Used in ad7192 driver.
* ak8975
- power regulator support.
* at91-sama5d2
- differential channel support.
* mma8452
- runtime pm support
- drop device specific autosleep and use the runtime pm one instead.
* ms5611
- DT bindings
- oversampling ratio support
Cleanups and minor fixes
* MAINTAINERS
- Peter got married - hence name change!
* Documentation
- Fix a typo in in_proximity_raw description.
- Add some missing docs for iio_buffer_access_funcs.
* Tools
- update iio_event_monitor names to match new stuff.
- make generic_buffer look for triggers ending in -trigger as we let these in
for a number of drivers a long time back and now it is a fairly common
option.
Drivers
* staging wide
- convert bare unsigned usage to unsigned int to comply with coding style.
* non staging wide:
- since boiler plate gpio handling of interrupts has been moved into the
ACPI core we don't need to include gpio/consumer.h in a load of drivers so
drop it.
* ad7606
- fix an endian casting sparse warning.
* ak8975
- fix a possible unitialized warning from gcc.
- drop and unused field left over from earlier cleanups
- fix a missing regulator_disable on exit.
* at91-sama5d2
- typo and indentation
- missing IOMEM dependency.
- cleanup mode register usage by avoidling erasing whole thing when changing
the sampling frequency.
* bmc150
- use the core demux and available_scan_masks to simplify buffer handling
- optimize the transfers in the trigger handler now we have a magic function
to emulate bulk reads (under circumstances met here). This matters with some
rather dumb i2c adapters in particular.
- use a single regmap_conf for all bus types as they were all the same.
* bmg160
- use the core demux and available_scan_masks to simplify the buffer handling
- optimize the transfers in the trigger handler now we have a magic funciton
to emulate bulk rads (under circumstances met here).
- drop gpio interrupt probing from the driver (ACPI) as now handled by the
ACPI core.
* ina2xx-adc
- update the CALIB register when RShunt changes.
- fix scale for VShunt - in reality this error canceled out when used.
* isl29028
- use regmap to retrieve the struct device instead of carrying a second
copy of it around.
* kxcjk-1013
- use core demux
- optimize i2c transfers in the trigger handler.
* mcp4531
- refactor to use a pointer to access model parameters instead of indexing
into the array each time.
* mma8452
- style fixes
- avoid swtiching to active whenever the config changes
- add missin i2c_device_id for mma8451
* mpu6050
- fix possible NULL dereference.
- fix the name / chip_id used when ACPI used (otherwise reports as NULL).
* ms5611
- fix a missing regulator_disable that left the regulator on during removal.
* mxc4005
- drop gpio interrupt handling for ACPI case from driver as the core now
handles this case.
* st-sensors
- note that there are only ever a maximum of 3 axis on current st-sensors
so just allocate a fixed sized buffer big enough for that.
* tpl0102
- change the i2c_check_functionality condition to bring it inline with other
IIO users as EOPNOTSUPP.
* tsl2563
- replace deprecated flush_scheduled_work
- Freescale Touch Screen ADC
- X-Powers AXP PMIC with RSB
- TI TPS65086 Power Management IC (PMIC)
- New Device Support
- Supply device PCI IDs for Intel Broxton
- Fix-ups
- Move to clkdev_create() API; intel_quark_i2c_gpio
- Complete re-write of TI's TPS65912 Power Management IC (PMIC)
- Remove unnecessary function argument; axp20x
- Separate out bus related code; axp20x
- Coding Style changes; axp20x
- Allow more drivers to be compiled as modules
- Work around false positive 'used uninitialised' warning; db8500-prcmu
- Bug Fixes
- Remove do_div(); fsl-imx25-gcq
- Fix driver init when built-in; tps65010
- Fix clock-unregister leak; intel-lpss
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gTBA
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Freescale Touch Screen ADC
- X-Powers AXP PMIC with RSB
- TI TPS65086 Power Management IC (PMIC)
New Device Support:
- Supply device PCI IDs for Intel Broxton
Fix-ups:
- Move to clkdev_create() API; intel_quark_i2c_gpio
- Complete re-write of TI's TPS65912 Power Management IC (PMIC)
- Remove unnecessary function argument; axp20x
- Separate out bus related code; axp20x
- Coding Style changes; axp20x
- Allow more drivers to be compiled as modules
- Work around false positive 'used uninitialised' warning; db8500-prcmu
Bug Fixes:
- Remove do_div(); fsl-imx25-gcq
- Fix driver init when built-in; tps65010
- Fix clock-unregister leak; intel-lpss"
* tag 'mfd-for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (53 commits)
mfd: intel-lpss: Pass I2C configuration via properties on BXT
mfd: imx6sx: Add PCIe register definitions for iomuxc gpr
mfd: ipaq-micro: Use __maybe_unused to hide pm functions
mfd: max77686: Add max77802 to I2C device ID table
mfd: max77686: Export OF module alias information
mfd: max77686: Allow driver to be built as a module
mfd: stmpe: Add the proper PWM resources
mfd: tps65090: Set regmap config reg counts properly
mfd: syscon: Return ENOTSUPP instead of ENOSYS when disabled
mfd: as3711: Set regmap config reg counts properly
mfd: rc5t583: Set regmap config reg counts properly
gpio: tps65086: Add GPO driver for the TPS65086 PMIC
mfd: mt6397: Add platform device ID table
mfd: da9063: Fix missing volatile registers in the core regmap_range volatile lists
mfd: mt6397: Add MT6323 support to MT6397 driver
mfd: mt6397: Add support for different Slave types
mfd: mt6397: int_con and int_status may vary in location
dt-bindings: mfd: Add bindings for the MediaTek MT6323 PMIC
mfd: da9062: Fix missing volatile registers in the core regmap_range volatile lists
mfd: Add documentation for ACT8945A DT bindings
...
Add base support for the 10-bit SAR ADC peripheral found
on NXP LPC18xx/43xx SoCs.
This is a minimal driver that does not support burst mode,
interrupts, DMA or hardware triggers.
User manual with register description can be found on:
LPC18xx: www.nxp.com/documents/user_manual/UM10430.pdf
LPC43xx: www.nxp.com/documents/user_manual/UM10503.pdf
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The devres.o gets linked if HAS_IOMEM is present so on ARCH=um
allyesconfig (COMPILE_TEST) failed with:
drivers/built-in.o: In function `at91_adc_probe':
at91-sama5d2_adc.c:(.text+0x48f548): undefined reference to `devm_ioremap_resource'
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
New Device Support
* Apex stx104 DAC
- new driver for this PC104 board. Right now DAC support only.
* ADI ad5064
- Add support for ad5625, ad5627, ad5645, ad5665, ad5667 DACs.
- Add support for Linear Technology ltc2606, ltc2607, ltc2609, ltc2616,
ltc2617, ltc2619, ltc2626, ltc2627 and ltc2629.
* ADI ad7192
- add support for the ad7193
* Invensense mpu6050
- substantial rework of driver to use regmap allowing SPI support extending
the now split driver to cover the MPU6000.
* TI adc0832
- new driver supporting ADC0831, ADC0832, ADC0834 and ADC0838 ADCs.
* TI ads1015
- new driver, note that there is an existing hwmon driver. The long term
intention is to probably remove the hwmon driver but for now we just have
guards in place to ensure this driver is not built if that one is enabled.
* TI afe4403
- new driver for this heart rate monitor / pulse oximeter front end chip.
* TI afe4404
- new driver for this heart rate monitor / pulse oximeter front end chip.
Staging Graduations
* mxs-lradc
- A combined general purpose and touch screen (input) device driver.
Originally held in staging to allow reworking into and MFD but as
that wasn't happening and isn't an absolute requirement we are moving
it out of staging.
Driver new features
* ms5611
- triggered buffer support
- IIO_CHAN_INFO_SCALE to aid the triggered buffer support.
Driver cleanups / reworks / fixes
* ad5064
- Use an enum for the register map layout to allow support of additional
chips (precursor to the new support listed above).
- Structural driver changes to allow support of the slightly different
handling for the ltc parts above.
* ad5933
- drop an exceptional & unnecessary for a function pointer.
* ad7606
- Cleanup the repeated copies of pm ops.
- consolidate the various channels specs via a sport of rearranging so only
one version is needed.
* atlas ph sensor
- add select IRQ_WORK
* hmc8543 (soon to move out of staging)
- Comment style fixes
- functionality of suspend and resume was swapped.
* spear-adc
- use devm_clk_dev instead of managing the clk lifetime by hand.
Core
* Use new dmaengine_terminate_sync call to avoid a theoretical race.
* Fix docs for mlock in struct iio_dev as it is correctly taken in some
drivers (docs used to say for core only).
* Add a helper function for calculating the scan index storage size within
the core cutting out some cut and paste versions of the same code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=LIQe
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.6b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
2nd round of new IIO device support, features and cleanups for the 4.6 cycle.
New Device Support
* Apex stx104 DAC
- new driver for this PC104 board. Right now DAC support only.
* ADI ad5064
- Add support for ad5625, ad5627, ad5645, ad5665, ad5667 DACs.
- Add support for Linear Technology ltc2606, ltc2607, ltc2609, ltc2616,
ltc2617, ltc2619, ltc2626, ltc2627 and ltc2629.
* ADI ad7192
- add support for the ad7193
* Invensense mpu6050
- substantial rework of driver to use regmap allowing SPI support extending
the now split driver to cover the MPU6000.
* TI adc0832
- new driver supporting ADC0831, ADC0832, ADC0834 and ADC0838 ADCs.
* TI ads1015
- new driver, note that there is an existing hwmon driver. The long term
intention is to probably remove the hwmon driver but for now we just have
guards in place to ensure this driver is not built if that one is enabled.
* TI afe4403
- new driver for this heart rate monitor / pulse oximeter front end chip.
* TI afe4404
- new driver for this heart rate monitor / pulse oximeter front end chip.
Staging Graduations
* mxs-lradc
- A combined general purpose and touch screen (input) device driver.
Originally held in staging to allow reworking into and MFD but as
that wasn't happening and isn't an absolute requirement we are moving
it out of staging.
Driver new features
* ms5611
- triggered buffer support
- IIO_CHAN_INFO_SCALE to aid the triggered buffer support.
Driver cleanups / reworks / fixes
* ad5064
- Use an enum for the register map layout to allow support of additional
chips (precursor to the new support listed above).
- Structural driver changes to allow support of the slightly different
handling for the ltc parts above.
* ad5933
- drop an exceptional & unnecessary for a function pointer.
* ad7606
- Cleanup the repeated copies of pm ops.
- consolidate the various channels specs via a sport of rearranging so only
one version is needed.
* atlas ph sensor
- add select IRQ_WORK
* hmc8543 (soon to move out of staging)
- Comment style fixes
- functionality of suspend and resume was swapped.
* spear-adc
- use devm_clk_dev instead of managing the clk lifetime by hand.
Core
* Use new dmaengine_terminate_sync call to avoid a theoretical race.
* Fix docs for mlock in struct iio_dev as it is correctly taken in some
drivers (docs used to say for core only).
* Add a helper function for calculating the scan index storage size within
the core cutting out some cut and paste versions of the same code.
The driver has sysfs readings with runtime PM support for power saving.
It also offers buffer support that can be used together with IIO software
triggers.
Datasheet can be found here:
http://www.ti.com.cn/cn/lit/ds/symlink/ads1015.pdf
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This is a conversion queue driver for the mx25 SoC. It uses the central
ADC which is used by two seperate independent queues. This driver
prepares different conversion configurations for each possible input.
For a conversion it creates a conversionqueue of one item with the
correct configuration for the chosen channel. It then executes the queue
once and disables the conversion queue afterwards.
The reference voltages are configurable through devicetree subnodes,
depending on the connections of the ADC inputs.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Akinobu Mita
Linus Walleij
Quentin Schulz
Jacopo Mondi
Arnd Bergmann
Michael Hennerich
Rick Altherr
Tony Lindgren
William Breathitt Gray
Jonathan Cameron
Fabrice Gasnier
Martin Blumenstingl
Marek Vasut
Greg Kroah-Hartman
Phil Reid
Jacopo Mondi
Andreas Klinger
Geert Uytterhoeven
David Lechner
Peter Rosin
Mika Westerberg
Lars-Peter Clausen
Alison Schofield
Caesar Wang
Zhiyong Tao
Matt Ranostay
Raveendra Padasalagi
Crestez Dan Leonard
Linus Torvalds
Joachim Eastwood
Krzysztof Kozlowski
Daniel Baluta
Markus Pargmann
Ksenija Stanojevic