I forgot to move the digi*.h files from drivers/char/ to
drivers/staging/tty/
Thanks to Randy for pointing out the issue.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If a virtio-console device gets unplugged while a port is open, a
subsequent close() call on the port accesses vqs to free up buffers.
This can lead to a crash.
The buffers are already freed up as a result of the call to
unplug_ports() from virtcons_remove(). The fix is to simply not access
vq information if port->portdev is NULL.
Reported-by: juzhang <juzhang@redhat.com>
CC: stable@kernel.org
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit c4ff4b829e.
Ted Ts'o reports:
"TPM is working for me so I can log into employer's network in 2.6.37.
It broke when I tried 2.6.38-rc6, with the following relevant lines
from my dmesg:
[ 11.081627] tpm_tis 00:0b: 1.2 TPM (device-id 0x0, rev-id 78)
[ 25.734114] tpm_tis 00:0b: Operation Timed out
[ 78.040949] tpm_tis 00:0b: Operation Timed out
This caused me to get suspicious, especially since the _other_ TPM
commit in 2.6.38 had already been reverted, so I tried reverting
commit c4ff4b829e: "TPM: Long default timeout fix". With this commit
reverted, my TPM on my Lenovo T410 is once again working."
Requested-and-tested-by: Theodore Ts'o <tytso@mit.edu>
Acked-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ioctl file pointer was removed in commit 6caa76
"tty: now phase out the ioctl file pointer for good".
Thus fix the prototype for mgslpc_ioctl() and eliminate below warning:
CC [M] drivers/char/pcmcia/synclink_cs.o
drivers/char/pcmcia/synclink_cs.c:2787: warning: initialization from incompatible pointer type
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
of_platform_driver is getting removed, and a single platform_driver
can now support both devicetree and non-devicetree use cases. This
patch merges the two driver registrations.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
of_bus is deprecated in favor of the plain platform bus. This patch
merges the ipmi OF driver with the existing platform driver.
CONFIG_PPC_OF occurrances are removed or replaced with CONFIG_OF.
Compile tested with and without CONFIG_OF. Tested OF probe and
default probe cases.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Get rid of old users of of_platform_driver in arch/sparc. Most
of_platform_driver users can be converted to use the platform_bus
directly.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Get rid of old users of of_platform_driver in arch/powerpc. Most
of_platform_driver users can be converted to use the platform_bus
directly.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This caused a build error. Many thanks to Stephen Rothwell for pointing
this mistake out.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel:
drm/i915: fix corruptions on i8xx due to relaxed fencing
drm/i915: skip FDI & PCH enabling for DP_A
agp/intel: Experiment with a 855GM GWB bit
drm/i915: don't enable FDI & transcoder interrupts after all
drm/i915: Ignore a hung GPU when flushing the framebuffer prior to a switch
Make Primecell driver probe functions take a const pointer to their
ID tables. Drivers should never modify their ID tables in their
probe handler.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The module forgot to sometimes unregister some resources.
This fixes Bug #22882.
[Patch updated to 2.6.38-rc3 by Randy Dunlap.]
Tested-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Florian Mickler <florian@mickler.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
As planned by Arnd Bergmann, this moves the following drivers to the
drivers/staging/generic_serial directory where they will be removed
after 2.6.41 if no one steps up to claim them.
generic_serial
rio
ser_a2232
sx
vme_scc
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As planned by Arnd Bergmann, this moves the following drivers to the
drivers/staging/tty/ directory where they will be removed after 2.6.41
if no one steps up to claim them.
epca
epca
ip2
istallion
riscom8
serial167
specialix
stallion
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As planned by Arnd Bergmann, this moves the ipwireless driver to the
drivers/tty/ directory as that's where it really belongs.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: David Sterba <dsterba@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As planned by Arnd Bergmann, this moves the following drivers from
drivers/char/ to drivers/tty/ as that's where they really belong:
amiserial
nozomi
synclink
rocket
cyclades
moxa
mxser
isicom
bfin_jtag_comm
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Kconfig options for the drivers/tty/ files still were hanging around
in the "big" drivers/char/Kconfig file, so move them to the proper
location under drivers/tty and drivers/tty/hvc/
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
pcmcia: re-enable Zoomed Video support
cm4000_cs: Fix undefined ops warning
pcmcia vs. MECR on pxa25x/sa1111
drivers/char/pcmcia/ipwireless/main.c: Convert release_resource to release_region/release_mem_region
This converts the ia64 clocksources to use clocksource_register_hz/khz
CC: Tony Luck <tony.luck@intel.com>
CC: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Tony Luck <tony.luck@intel.com> [clocksource_itc path]
Signed-off-by: John Stultz <johnstul@us.ibm.com>
At present, the comment header in random.c makes no mention of
add_disk_randomness, and instead, suggests that disk activity adds to the
random pool by way of add_interrupt_randomness, which appears to not have
been the case since sometime prior to the existence of git, and even prior
to bitkeeper. Didn't look any further back. At least, as far as I can
tell, there are no storage drivers setting IRQF_SAMPLE_RANDOM, which is a
requirement for add_interrupt_randomness to trigger, so the only way for a
disk to contribute entropy is by way of add_disk_randomness. Update
comments accordingly, complete with special mention about solid state
drives being a crappy source of entropy (see e2e1a148bc for reference).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This reverts commit 9b29050f8f.
It has caused hibernate regressions, for example Juri Sladby's report:
"I'm unable to hibernate 2.6.37.1 unless I rmmod tpm_tis:
[10974.074587] Suspending console(s) (use no_console_suspend to debug)
[10974.103073] tpm_tis 00:0c: Operation Timed out
[10974.103089] legacy_suspend(): pnp_bus_suspend+0x0/0xa0 returns -62
[10974.103095] PM: Device 00:0c failed to freeze: error -62"
and Rafael points out that some of the new conditionals in that commit
seem to make no sense. This commit needs more work and testing, let's
revert it for now.
Reported-by: Norbert Preining <preining@logic.at>
Reported-and-requested-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Stefan Berger <stefanb@linux.vnet.ibm.com>
Cc: Guillaume Chazarain <guichaz@gmail.com>
Cc: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Request_region should be used with release_region, not release_resource.
This patch contains a number of changes, related to calls to request_region,
request_mem_region, and the associated error handling code.
1. For the call to request_region, the variable io_resource storing the
result is dropped. The call to release_resource at the end of the function
is changed to a call to release_region with the first two arguments of
request_region as its arguments. The same call to release_region is also
added to release_ipwireless.
2. The first call to request_mem_region is now tested and ret is set to
-EBUSY if the the call has failed. This call was associated with the
initialization of ipw->attr_memory. But the error handling code was
testing ipw->common_memory. The definition of release_ipwireless also
suggests that this call should be associated with ipw->common_memory, not
ipw->attr_memory.
3. The second call to request_mem_region is now tested and ret is
set to -EBUSY if the the call has failed.
4. The various gotos to the error handling code is adjusted so that there
is no need for ifs.
5. Return the value stored in the ret variable rather than -1.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,E;
@@
(
*x = request_region(...)
|
*x = request_mem_region(...)
)
... when != release_region(x)
when != x = E
* release_resource(x);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Only oddities here are a couple of drivers that bogusly called the ldisc
helpers instead of returning -ENOIOCTLCMD. Fix the bug and the rest goes
away.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Doing tiocmget was such fun we should do tiocmset as well for the same
reasons
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't actually need this and it causes problems for internal use of
this functionality. Currently there is a single use of the FILE * pointer.
That is the serial core which uses it to check tty_hung_up_p. However if
that is true then IO_ERROR is also already set so the check may be removed.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This converts the existing bfin_jtag_comm TTY driver to the HVC layer so
that the common HVC code can worry about all of the TTY/polling crap and
leave the Blackfin code to worry about the Blackfin bits.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Request_region should be used with release_region, not release_resource.
The local variable mem, storing the result of request_mem_region, is
dropped and instead the pointer res is stored in the drvdata field of the
platform device. This information is retrieved in omap_rng_remove to
release the region. The drvdata field is not used elsewhere.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,E;
@@
(
*x = request_region(...)
|
*x = request_mem_region(...)
)
... when != release_region(x)
when != x = E
* release_resource(x);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The current TPM TIS driver in git discards the timeout values returned
from the TPM. The check of the response packet needs to consider that
the return_code field is 0 on success and the size of the expected
packet is equivalent to the header size + u32 length indicator for the
TPM_GetCapability() result + 3 timeout indicators of type u32.
I am also adding a sysfs entry 'timeouts' showing the timeouts that are
being used.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: Guillaume Chazarain <guichaz@gmail.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
This patch fixes an OOPS triggered when calling modprobe ipmi_si a
second time after the first modprobe returned without finding any ipmi
devices. This can happen if you reload the module after having the
first module load fail. The driver was not deregistering from PNP in
that case.
Peter Huewe originally reported this patch and supplied a fix, I have a
different patch based on Linus' suggestion that cleans things up a bit
more.
Cc: stable@kernel.org
Cc: openipmi-developer@lists.sourceforge.net
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
serial: bfin_5xx: split uart RX lock from uart port lock to avoid deadlock
68360serial: Plumb in rs_360_get_icount()
n_gsm: copy mtu over when configuring via ioctl interface
virtio: console: Move file back to drivers/char/
Some BIOSs (eg. the AMI BIOS on the Asus P4P800 motherboard) don't
initialise the GART address, and pcibios_assign_resources() can ignore it
because it can be marked as a host bridge (see
https://bugzilla.kernel.org/show_bug.cgi?id=24392#c5 for details). This
was handled correctly up to 2.6.35, but the pci_enable_device() cleanup in
2.6.36 96576a9e1a ("agp: intel-agp: do not use PCI resources before
pci_enable_device()") means that the kernel tries to enable the GART
before assigning it an address; in such cases the GART overlaps with other
device assignments and ends up being disabled.
This patch fixes https://bugzilla.kernel.org/show_bug.cgi?id=24392
Note that I imagine efficeon-agp.c probably has the same problem, but
I can't test that and I'd like to make sure this patch is suitable for
-stable (since 2.6.36 and 2.6.37 are affected).
Signed-off-by: Stephen Kitt <steve@sk2.org>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Maciej Rutecki <maciej.rutecki@gmail.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Kulikov Vasiliy <segooon@gmail.com>
Cc: Florian Mickler <florian@mickler.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit f191f14407.
The AMD 751 and 761 chipsets are used on the UP1000, UP1100, and UP1500
OEM motherboards, but they neglect to do anything to make AGP work.
According to Ivan Kokshaysky:
There is quite fundamental conflict between the Alpha architecture and
x86 AGP implementation - Alpha is entirely cache coherent by design,
while x86 AGP is not (I mean native AGP DMA transactions, not a PCI over
AGP). There are no such things as non-cacheable mappings or software
support for cache flushing/invalidation on Alpha, so x86 AGP code won't
work on Nautilus.
So there's no point in allowing this driver to be configured on Alpha.
Signed-off-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
amd-k7-agp can't be built on Alpha anymore, so remove now unnecessary
code.
Signed-off-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit 728674a7e4 moved virtio_console.c
to drivers/tty/hvc/ under the perception of this being an hvc driver.
It was such once, but these days it has generic communication
capabilities as well, so move it to drivers/char/.
In the future, the hvc part from this file can be split off and moved
under drivers/tty/hvc/.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rename register_posix_clock() to posix_timers_register_clock(). That's
what the function really does. As a side effect this cleans up the
posix_clock namespace for the upcoming dynamic posix_clock
infrastructure.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Richard Cochran <richard.cochran@omicron.at>
Cc: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <alpine.LFD.2.00.1102021222240.31804@localhost6.localdomain6>
The res member of kclock is only used by mmtimer.c, but even there it
contains redundant information. Remove the field and fixup mmtimer.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: John Stultz <johnstul@us.ibm.com>
Tested-by: Richard Cochran <richard.cochran@omicron.at>
LKML-Reference: <20110201134418.808714587@linutronix.de>
Use the new kclock decoding. Fixup the fallout in mmtimer.c
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: John Stultz <johnstul@us.ibm.com>
Tested-by: Richard Cochran <richard.cochran@omicron.at>
LKML-Reference: <20110201134418.709802797@linutronix.de>
Use the new kclock decoding function in clock_nanosleep and cleanup all
kclocks which use the default functions.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: John Stultz <johnstul@us.ibm.com>
Tested-by: Richard Cochran <richard.cochran@omicron.at>
LKML-Reference: <20110201134418.034175556@linutronix.de>
Cosmetic. No functional change
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: John Stultz <johnstul@us.ibm.com>
Tested-by: Richard Cochran <richard.cochran@omicron.at>
LKML-Reference: <20110201134417.745627057@linutronix.de>
Both settimeofday() and clock_settime() promise with a 'const'
attribute not to alter the arguments passed in. This patch adds the
missing 'const' attribute into the various kernel functions
implementing these calls.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Acked-by: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <20110201134417.545698637@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The -rt patches change the console_semaphore to console_mutex. As a
result, a quite large chunk of the patches changes all
acquire/release_console_sem() to acquire/release_console_mutex()
This commit makes things use more neutral function names which dont make
implications about the underlying lock.
The only real change is the return value of console_trylock which is
inverted from try_acquire_console_sem()
This patch also paves the way to switching console_sem from a semaphore to
a mutex.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: make console_trylock return 1 on success, per Geert]
Signed-off-by: Torben Hohn <torbenh@gmx.de>
Cc: Thomas Gleixner <tglx@tglx.de>
Cc: Greg KH <gregkh@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge with Linus to resolve conflicting fixes for the reusing the stale
HEAD value during intel_ring_wait().
Conflicts:
drivers/gpu/drm/i915/intel_ringbuffer.c
We can only utilize the stolen portion of the GTT if we are in sole
charge of the hardware. This is only true if using GEM and KMS,
otherwise VESA continues to access stolen memory.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Frederic Weisbecker <fweisbec@gmail.com>
Tested-by: Jiri Olsa <jolsa@redhat.com>
Tested-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
commit 3f0d3d016d adds a check for
PNP device id to the common tpm_tis_init() function, which in some
cases (force=1) will be called without the device being a member of
a pnp_dev. Oopsing and panics ensue.
Move the test up to before the call to tpm_tis_init(), since it
just modifies a global variable anyway.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
If duration variable value is 0 at this point, it's because
chip->vendor.duration wasn't filled by tpm_get_timeouts() yet.
This patch sets then the lowest timeout just to give enough
time for tpm_get_timeouts() to further succeed.
This fix avoids long boot times in case another entity attempts
to send commands to the TPM when the TPM isn't accessible.
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
This driver adds support for the True Random Number Generator in
the Picochip PC3X3 and later devices.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
* akpm:
kernel/smp.c: consolidate writes in smp_call_function_interrupt()
kernel/smp.c: fix smp_call_function_many() SMP race
memcg: correctly order reading PCG_USED and pc->mem_cgroup
backlight: fix 88pm860x_bl macro collision
drivers/leds/ledtrig-gpio.c: make output match input, tighten input checking
MAINTAINERS: update Atmel AT91 entry
mm: fix truncate_setsize() comment
memcg: fix rmdir, force_empty with THP
memcg: fix LRU accounting with THP
memcg: fix USED bit handling at uncharge in THP
memcg: modify accounting function for supporting THP better
fs/direct-io.c: don't try to allocate more than BIO_MAX_PAGES in a bio
mm: compaction: prevent division-by-zero during user-requested compaction
mm/vmscan.c: remove duplicate include of compaction.h
memblock: fix memblock_is_region_memory()
thp: keep highpte mapped until it is no longer needed
kconfig: rename CONFIG_EMBEDDED to CONFIG_EXPERT
The meaning of CONFIG_EMBEDDED has long since been obsoleted; the option
is used to configure any non-standard kernel with a much larger scope than
only small devices.
This patch renames the option to CONFIG_EXPERT in init/Kconfig and fixes
references to the option throughout the kernel. A new CONFIG_EMBEDDED
option is added that automatically selects CONFIG_EXPERT when enabled and
can be used in the future to isolate options that should only be
considered for embedded systems (RISC architectures, SLOB, etc).
Calling the option "EXPERT" more accurately represents its intention: only
expert users who understand the impact of the configuration changes they
are making should enable it.
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: David Woodhouse <david.woodhouse@intel.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Greg KH <gregkh@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Robin Holt <holt@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty: update MAINTAINERS file due to driver movement
tty: move drivers/serial/ to drivers/tty/serial/
tty: move hvc drivers to drivers/tty/hvc/
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel:
drm/i915/lvds: Add AOpen i915GMm-HFS to the list of false-positive LVDS
agp/intel: Fix device names of i845 and 845G
drm/i915: Disable GPU semaphores on SandyBridge mobile
drm/i915/execbuffer: Clear domains before beginning reloc processing
drm/i915/execbuffer: Reorder relocations to match new object order
drm/i915: Fix error handler to capture the first batch after the seqno
drm/i915: Add a module option to override the use of SSC
drm/i915/panel: The backlight is enabled if the current value is non-zero
drm/i915/debugfs: Correct format after changing type of err object 'size'
They got mixed up when the switch was converted to a table in 2007.
Signed-off-by: Oswald Buddenhagen <ossi@kde.org>
[ickle: minor changes for 2.6.37+]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (59 commits)
ACPI / PM: Fix build problems for !CONFIG_ACPI related to NVS rework
ACPI: fix resource check message
ACPI / Battery: Update information on info notification and resume
ACPI: Drop device flag wake_capable
ACPI: Always check if _PRW is present before trying to evaluate it
ACPI / PM: Check status of power resources under mutexes
ACPI / PM: Rename acpi_power_off_device()
ACPI / PM: Drop acpi_power_nocheck
ACPI / PM: Drop acpi_bus_get_power()
Platform / x86: Make fujitsu_laptop use acpi_bus_update_power()
ACPI / Fan: Rework the handling of power resources
ACPI / PM: Register power resource devices as soon as they are needed
ACPI / PM: Register acpi_power_driver early
ACPI / PM: Add function for updating device power state consistently
ACPI / PM: Add function for device power state initialization
ACPI / PM: Introduce __acpi_bus_get_power()
ACPI / PM: Introduce function for refcounting device power resources
ACPI / PM: Add functions for manipulating lists of power resources
ACPI / PM: Prevent acpi_power_get_inferred_state() from making changes
ACPICA: Update version to 20101209
...
The serial drivers are really just tty drivers, so move them to
drivers/tty/ to make things a bit neater overall.
This is part of the tty/serial driver movement proceedure as proposed by
Arnd Bergmann and approved by everyone involved a number of months ago.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Rogier Wolff <R.E.Wolff@bitwizard.nl>
Cc: Michael H. Warfield <mhw@wittsend.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As requested by Arnd Bergmann, the hvc drivers are now
moved to the drivers/tty/hvc/ directory. The virtio_console.c driver
was also moved, as it required the hvc_console.h file to be able to be
built, and it really is a hvc driver.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-2.6.38/core' of git://git.kernel.dk/linux-2.6-block: (43 commits)
block: ensure that completion error gets properly traced
blktrace: add missing probe argument to block_bio_complete
block cfq: don't use atomic_t for cfq_group
block cfq: don't use atomic_t for cfq_queue
block: trace event block fix unassigned field
block: add internal hd part table references
block: fix accounting bug on cross partition merges
kref: add kref_test_and_get
bio-integrity: mark kintegrityd_wq highpri and CPU intensive
block: make kblockd_workqueue smarter
Revert "sd: implement sd_check_events()"
block: Clean up exit_io_context() source code.
Fix compile warnings due to missing removal of a 'ret' variable
fs/block: type signature of major_to_index(int) to major_to_index(unsigned)
block: convert !IS_ERR(p) && p to !IS_ERR_NOR_NULL(p)
cfq-iosched: don't check cfqg in choose_service_tree()
fs/splice: Pull buf->ops->confirm() from splice_from_pipe actors
cdrom: export cdrom_check_events()
sd: implement sd_check_events()
sr: implement sr_check_events()
...
Cc: Ahmed S. Darwish <darwish.07@gmail.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marco Stornelli <marco.stornelli@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The newer drivers/gpio/cs5535-gpio.c replaces drivers/misc/cs5535_gpio.c.
The new driver has been in the tree for a little while, and has received
some testing; it's time to mark the old one as deprecated. I'm thinking
removal around 2.6.40 would be good, provided we're not missing critical
functionality in the newer driver.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Cc: Daniel Drake <dsd@laptop.org>
Acked-by: Ben Gardner <bgardner@wabtec.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This series aims to develop logging facility for enterprise use.
It is important to save kernel messages reliably on enterprise system
because they are helpful for diagnosing system.
This series add kmsg_dump() to the paths loosing kernel messages. The use
case is the following.
[Use case of reboot/poweroff/halt/emergency_restart]
My company has often experienced the followings in our support service.
- Customer's system suddenly reboots.
- Customers ask us to investigate the reason of the reboot.
We recognize the fact itself because boot messages remain in
/var/log/messages. However, we can't investigate the reason why the
system rebooted, because the last messages don't remain. And off course
we can't explain the reason.
We can solve above problem with this patch as follows.
Case1: reboot with command
- We can see "Restarting system with command:" or ""Restarting system.".
Case2: halt with command
- We can see "System halted.".
Case3: poweroff with command
- We can see " Power down.".
Case4: emergency_restart with sysrq.
- We can see "Sysrq:" outputted in __handle_sysrq().
Case5: emergency_restart with softdog.
- We can see "Initiating system reboot" in watchdog_fire().
So, we can distinguish the reason of reboot, poweroff, halt and emergency_restart.
If customer executed reboot command, you may think the customer should
know the fact. However, they often claim they don't execute the command
when they rebooted system by mistake.
No message remains on the current Linux kernel, so we can't show the proof
to the customer. This patch improves this situation.
This patch:
Alters mtdoops and ramoops to perform their actions only for
KMSG_DUMP_PANIC, KMSG_DUMP_OOPS and KMSG_DUMP_KEXEC because they would
like to log crashes only.
Signed-off-by: Seiji Aguchi <seiji.aguchi@hds.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Marco Stornelli <marco.stornelli@gmail.com>
Reviewed-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The new GPE handler callback has 2 additional parameters, gpe_device and
gpe_number.
typedef
u32 (*acpi_gpe_handler) (acpi_handle gpe_device, u32 gpe_number, void *context);
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Previous to the last GTT rework we always rewrote the GTT then unmapped the
object, somehow this got reversed in the rework in 2.6.37-rc5 timeframe.
This fix needs to go to stable in an alternate form since the code changed.
This fixes DMAR reports on my Ironlake HP2540p.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This code was setting up the status page before setting the DMAR-is-on-bit,
so we were getting DMAR errors on the status page. Reverse the two bits
of init code to the correct result.
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-intel-fixes' of ssh://master.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel: (37 commits)
drm/i915/execbuffer: Reorder binding of objects to favour restrictions
drm/i915: If we hit OOM when allocating GTT pages, clear the aperture
drm/i915/evict: Ensure we completely cleanup on failure
drm/i915/execbuffer: Correctly clear the current object list upon EFAULT
drm/i915/debugfs: Show all objects in the gtt
drm/i915: Record AGP memory type upon error
drm/i915: Periodically flush the active lists and requests
drm/i915/gtt: Unmap the PCI pages after unbinding them from the GTT
drm/i915: Record the error batchbuffer on each ring
drm/i915: Include TLB miss overhead for computing WM
drm/i915: Propagate error from flushing the ring
drm/i915: detect & report PCH display error interrupts
drm/i915: cleanup rc6 code
drm/i915: fix rc6 enabling around suspend/resume
drm/i915: re-enable rc6 support for Ironlake+
drm/i915: Make the ring IMR handling private
drm/i915/ringbuffer: Simplify the ring irq refcounting
drm/i915/debugfs: Show the per-ring IMR
drm/i915: Mask USER interrupts on gen6 (until required)
drm/i915: Handle ringbuffer stalls when flushing
...
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (72 commits)
powerpc/pseries: Fix build of topology stuff without CONFIG_NUMA
powerpc/pseries: Fix VPHN build errors on non-SMP systems
powerpc/83xx: add mpc8308_p1m DMA controller device-tree node
powerpc/83xx: add DMA controller to mpc8308 device-tree node
powerpc/512x: try to free dma descriptors in case of allocation failure
powerpc/512x: add MPC8308 dma support
powerpc/512x: fix the hanged dma transfer issue
powerpc/512x: scatter/gather dma fix
powerpc/powermac: Make auto-loading of therm_pm72 possible
of/address: Use propper endianess in get_flags
powerpc/pci: Use printf extension %pR for struct resource
powerpc: Remove unnecessary casts of void ptr
powerpc: Disable VPHN polling during a suspend operation
powerpc/pseries: Poll VPA for topology changes and update NUMA maps
powerpc: iommu: Add device name to iommu error printks
powerpc: Record vma->phys_addr in ioremap()
powerpc: Update compat_arch_ptrace
powerpc: Fix PPC_PTRACE_SETHWDEBUG on PPC_BOOK3S
powerpc/time: printk time stamp init not correct
powerpc: Minor cleanups for machdep.h
...
Flush the chipset write buffers before and after adjusting the GTT base
register, just in case. We only modify this value upon initialisation
(boot and resume) so there should be no outstanding writes, however
there are always those persistent PGTBL_ER that keep getting reported
upon resume.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
* 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (390 commits)
drm/radeon/kms: disable underscan by default
drm/radeon/kms: only enable hdmi features if the monitor supports audio
drm: Restore the old_fb upon modeset failure
drm/nouveau: fix hwmon device binding
radeon: consolidate asic-specific function decls for pre-r600
vga_switcheroo: comparing too few characters in strncmp()
drm/radeon/kms: add NI pci ids
drm/radeon/kms: don't enable pcie gen2 on NI yet
drm/radeon/kms: add radeon_asic struct for NI asics
drm/radeon/kms/ni: load default sclk/mclk/vddc at pm init
drm/radeon/kms: add ucode loader for NI
drm/radeon/kms: add support for DCE5 display LUTs
drm/radeon/kms: add ni_reg.h
drm/radeon/kms: add bo blit support for NI
drm/radeon/kms: always use writeback/events for fences on NI
drm/radeon/kms: adjust default clock/vddc tracking for pm on DCE5
drm/radeon/kms: add backend map workaround for barts
drm/radeon/kms: fill gpu init for NI asics
drm/radeon/kms: add disabled vbios accessor for NI asics
drm/radeon/kms: handle NI thermal controller
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6: (30 commits)
MAINTAINERS: Add tomoyo-dev-en ML.
SELinux: define permissions for DCB netlink messages
encrypted-keys: style and other cleanup
encrypted-keys: verify datablob size before converting to binary
trusted-keys: kzalloc and other cleanup
trusted-keys: additional TSS return code and other error handling
syslog: check cap_syslog when dmesg_restrict
Smack: Transmute labels on specified directories
selinux: cache sidtab_context_to_sid results
SELinux: do not compute transition labels on mountpoint labeled filesystems
This patch adds a new security attribute to Smack called SMACK64EXEC. It defines label that is used while task is running.
SELinux: merge policydb_index_classes and policydb_index_others
selinux: convert part of the sym_val_to_name array to use flex_array
selinux: convert type_val_to_struct to flex_array
flex_array: fix flex_array_put_ptr macro to be valid C
SELinux: do not set automatic i_ino in selinuxfs
selinux: rework security_netlbl_secattr_to_sid
SELinux: standardize return code handling in selinuxfs.c
SELinux: standardize return code handling in selinuxfs.c
SELinux: standardize return code handling in policydb.c
...
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6: (29 commits)
of/flattree: forward declare struct device_node in of_fdt.h
ipmi: explicitly include of_address.h and of_irq.h
sparc: explicitly cast negative phandle checks to s32
powerpc/405: Fix missing #{address,size}-cells in i2c node
powerpc/5200: dts: refactor dts files
powerpc/5200: dts: Change combatible strings on localbus
powerpc/5200: dts: remove unused properties
powerpc/5200: dts: rename nodes to prepare for refactoring dts files
of/flattree: Update dtc to current mainline.
of/device: Don't register disabled devices
powerpc/dts: fix syntax bugs in bluestone.dts
of: Fixes for OF probing on little endian systems
of: make drivers depend on CONFIG_OF instead of CONFIG_PPC_OF
of/flattree: Add of_flat_dt_match() helper function
of_serial: explicitly include of_irq.h
of/flattree: Refactor unflatten_device_tree and add fdt_unflatten_tree
of/flattree: Reorder unflatten_dt_node
of/flattree: Refactor unflatten_dt_node
of/flattree: Add non-boottime device tree functions
of/flattree: Add Kconfig for EARLY_FLATTREE
...
Fix up trivial conflict in arch/sparc/prom/tree_32.c as per Grant.
Remove kobject.h from files which don't need it, notably,
sched.h and fs.h.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Conflicts:
security/smack/smack_lsm.c
Verified and added fix by Stephen Rothwell <sfr@canb.auug.org.au>
Ok'd by Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: James Morris <jmorris@namei.org>
* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (30 commits)
gameport: use this_cpu_read instead of lookup
x86: udelay: Use this_cpu_read to avoid address calculation
x86: Use this_cpu_inc_return for nmi counter
x86: Replace uses of current_cpu_data with this_cpu ops
x86: Use this_cpu_ops to optimize code
vmstat: User per cpu atomics to avoid interrupt disable / enable
irq_work: Use per cpu atomics instead of regular atomics
cpuops: Use cmpxchg for xchg to avoid lock semantics
x86: this_cpu_cmpxchg and this_cpu_xchg operations
percpu: Generic this_cpu_cmpxchg() and this_cpu_xchg support
percpu,x86: relocate this_cpu_add_return() and friends
connector: Use this_cpu operations
xen: Use this_cpu_inc_return
taskstats: Use this_cpu_ops
random: Use this_cpu_inc_return
fs: Use this_cpu_inc_return in buffer.c
highmem: Use this_cpu_xx_return() operations
vmstat: Use this_cpu_inc_return for vm statistics
x86: Support for this_cpu_add, sub, dec, inc_return
percpu: Generic support for this_cpu_add, sub, dec, inc_return
...
Fixed up conflicts: in arch/x86/kernel/{apic/nmi.c, apic/x2apic_uv_x.c, process.c}
as per Tejun.
* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (33 commits)
usb: don't use flush_scheduled_work()
speedtch: don't abuse struct delayed_work
media/video: don't use flush_scheduled_work()
media/video: explicitly flush request_module work
ioc4: use static work_struct for ioc4_load_modules()
init: don't call flush_scheduled_work() from do_initcalls()
s390: don't use flush_scheduled_work()
rtc: don't use flush_scheduled_work()
mmc: update workqueue usages
mfd: update workqueue usages
dvb: don't use flush_scheduled_work()
leds-wm8350: don't use flush_scheduled_work()
mISDN: don't use flush_scheduled_work()
macintosh/ams: don't use flush_scheduled_work()
vmwgfx: don't use flush_scheduled_work()
tpm: don't use flush_scheduled_work()
sonypi: don't use flush_scheduled_work()
hvsi: don't use flush_scheduled_work()
xen: don't use flush_scheduled_work()
gdrom: don't use flush_scheduled_work()
...
Fixed up trivial conflict in drivers/media/video/bt8xx/bttv-input.c
as per Tejun.
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (36 commits)
serial: apbuart: Fixup apbuart_console_init()
TTY: Add tty ioctl to figure device node of the system console.
tty: add 'active' sysfs attribute to tty0 and console device
drivers: serial: apbuart: Handle OF failures gracefully
Serial: Avoid unbalanced IRQ wake disable during resume
tty: fix typos/errors in tty_driver.h comments
pch_uart : fix warnings for 64bit compile
8250: fix uninitialized FIFOs
ip2: fix compiler warning on ip2main_pci_tbl
specialix: fix compiler warning on specialix_pci_tbl
rocket: fix compiler warning on rocket_pci_ids
8250: add a UPIO_DWAPB32 for 32 bit accesses
8250: use container_of() instead of casting
serial: omap-serial: Add support for kernel debugger
serial: fix pch_uart kconfig & build
drivers: char: hvc: add arm JTAG DCC console support
RS485 documentation: add 16C950 UART description
serial: ifx6x60: fix memory leak
serial: ifx6x60: free IRQ on error
Serial: EG20T: add PCH_UART driver
...
Fixed up conflicts in drivers/serial/apbuart.c with evil merge that
makes the code look fairly sane (unlike either side).
They are a handful of places in the code that register a die_notifier
as a catch all in case no claims the NMI. Unfortunately, they trigger
on events like DIE_NMI and DIE_NMI_IPI, which depending on when they
registered may collide with other handlers that have the ability to
determine if the NMI is theirs or not.
The function unknown_nmi_error() makes one last effort to walk the
die_chain when no one else has claimed the NMI before spitting out
messages that the NMI is unknown.
This is a better spot for these devices to execute any code without
colliding with the other handlers.
The two drivers modified are only compiled on x86 arches I believe, so
they shouldn't be affected by other arches that may not have
DIE_NMIUNKNOWN defined.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: Russ Anderson <rja@sgi.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: openipmi-developer@lists.sourceforge.net
Cc: dann frazier <dannf@hp.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1294348732-15030-3-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It has been reported that on at least one Nano CPU the xstore
instruction will write as many as 16 bytes of data to the output
buffer.
This causes memory corruption as we use rng->priv which is only
4-8 bytes long.
This patch fixes this by using an intermediate buffer on the stack
with at least 16 bytes and aligned to a 16-byte boundary.
The problem was observed on the following processor:
processor : 0
vendor_id : CentaurHauls
cpu family : 6
model : 15
model name : VIA Nano processor U2250 (1.6GHz Capable)
stepping : 3
cpu MHz : 1600.000
cache size : 1024 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 10
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat clflush acpi mmx fxsr sse sse2 ss tm syscall nx lm constant_tsc up rep_good pni monitor vmx est tm2 ssse3 cx16 xtpr rng rng_en ace ace_en ace2 phe phe_en lahf_lm
bogomips : 3192.08
clflush size : 64
cache_alignment : 128
address sizes : 36 bits physical, 48 bits virtual
power management:
Tested-by: Mario 'BitKoenig' Holbe <Mario.Holbe@TU-Ilmenau.DE>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The inline asm to invoke xstore did not specify the constraints
correctly. In particular, dx/di should have been marked as output
registers as well as input as they're modified by xstore.
Thanks to Mario Holbe for creating this patch and testing it.
Tested-by: Mario 'BitKoenig' Holbe <Mario.Holbe@TU-Ilmenau.DE>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
* 'x86-amd-nb-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, cacheinfo: Cleanup L3 cache index disable support
x86, amd-nb: Cleanup AMD northbridge caching code
x86, amd-nb: Complete the rename of AMD NB and related code
of_address.h and of_irq.h are implicitly included on powerpc. Adding
them fixes builds on non-powerpc platforms.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fixes for sdhci-of and ipmi drivers.
Auditing all drivers using of_get_property did not find other
occurrences likely to be used on LE platforms.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The current code mis-calculates the ramoops header size, leading to an
overflow over the next record at best, or over a non-allocated region at
worst. Fix that calculation.
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Acked-by: Marco Stornelli <marco.stornelli@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
flush_scheduled_work() is deprecated and scheduled to be removed.
Directly flush sonypi_device.input_work on removal instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Mattia Dongili <malattia@linux.it>
flush_scheduled_work() is deprecated and scheduled to be removed.
Directly cancel hp->writer and flush hp->handshaker instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
flush_scheduled_work() is deprecated and scheduled to be removed.
Directly flush the used works instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: David Sterba <dsterba@suse.cz>
__this_cpu_inc can create a single instruction to do the same as
__get_cpu_var()++.
Cc: Richard Kennedy <richard@rsk.demon.co.uk>
Cc: Matt Mackall <mpm@selenic.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This fixes regression from a6963596a1,
that missed to set cached memory type in GTT entry.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The IPMI smi_watcher will be used to catch the IPMI interface as they
come or go. In order to communicate with the correct IPMI device, it
should be confirmed whether it is what we wanted especially on the
system with multiple IPMI devices. But the new_smi callback function
of smi_watcher provides very limited info(only the interface number
and dev pointer) and there is no detailed info about the low level
interface. For example: which mechansim registers the IPMI
interface(ACPI, PCI, DMI and so on).
This is to add one interface that can get more info of low-level IPMI
device. For example: the ACPI device handle will be returned for the
pnp_acpi IPMI device.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Annotate ip2main_pci_tbl as '__used' to fix following warning:
CC drivers/char/ip2/ip2main.o
drivers/char/ip2/ip2main.c:3227: warning: ‘ip2main_pci_tbl’ defined but not used
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: "Michael H. Warfield" <mhw@wittsend.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Annotate specialx_pci_tbl as '__used' to fix following warning:
CC drivers/char/specialix.o
drivers/char/specialix.c:2358: warning: ‘specialx_pci_tbl’ defined but not used
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: Roger Wolff <R.E.Wolff@BitWizard.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Annotate rocket_pci_ids as '__used' to fix following warning:
CC drivers/char/rocket.o
drivers/char/rocket.c:1767: warning: ‘rocket_pci_ids’ defined but not used
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a missing NULL check and fix the wrong address passed to kunmap()
in i830_cleanup().
Cc: stable@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
[danvet: added cc stable]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This driver adds a basic console that uses the arm JTAG
DCC to transfer data back and forth. It has support for
ARMv6 and ARMv7.
This console is created under the HVC driver, and should be named
/dev/hvcX (or /dev/hvc0 for example).
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some Lenovos have TPMs that require a quirk to function correctly. This can
be autodetected by checking whether the device has a _HID of INTC0102. This
is an invalid PNPid, and as such is discarded by the pnp layer - however
it's still present in the ACPI code, so we can pull it out that way. This
means that the quirk won't be automatically applied on non-ACPI systems,
but without ACPI we don't have any way to identify the chip anyway so I
don't think that's a great concern.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Tested-by: Jiri Kosina <jkosina@suse.cz>
Tested-by: Andy Isaacson <adi@hexapodia.org>
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add internal kernel tpm_send() command used to seal/unseal keys.
Changelog:
- replaced module_put in tpm_send() with new tpm_chip_put() wrapper
(suggested by David Howells)
- Make tpm_send() cmd argument a 'void *' (suggested by David Howells)
Signed-off-by: David Safford <safford@watson.ibm.com>
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Serge E. Hallyn <serge.hallyn@canonical.com>
Signed-off-by: James Morris <jmorris@namei.org>
For readability, define a tpm_chip_put() wrapper to call module_put().
Replace existing module_put() calls with the wrapper.
(Change based on trusted/encrypted patchset review by David Howells.)
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
Signed-off-by: David Safford <safford@watson.ibm.com>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Serge E. Hallyn <serge.hallyn@canonical.com>
Signed-off-by: James Morris <jmorris@namei.org>
Stanse found that in init_vqs, memory is leaked under certain
circumstanses (the fail path order is incorrect). Fix that by checking
allocations in one turn and free all of them at once if some fails
(some may be NULL, but this is OK).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Amit Shah <amit.shah@redhat.com>
Cc: virtualization@lists.linux-foundation.org
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Just some minor shuffling to get rid of any agp traces in the
exported functions.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Its only user, intel-gtt.c is now gone.
Cc: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This still uses the agp functions to actually reinstate the mappings
(with a gross hack to make agp cooperate), but it wires everything
up correctly for the switchover.
The call to agp_rebind_memory can be dropped because all non-kms drivers
do all their rebinding on EnterVT.
v2: Be more paranoid and flush the chipset cache after restoring gtt
mappings.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The intel drm calls the chipset functions now directly. Userspace
never called the corresponding ioctl, hence it can be killed, too.
Cc: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Still a separate agp_bridge_driver because of the i81x-only
dedicated vram support.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Initialization is still done with the old code with a few
added things sprinkled in to make the intel_fake_agp helper
functions work.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Used for the now dead agp type_to_mask stuff.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
i830_check_flags already disallows it, so no need to implement it
in the write_entry function. Seems to be a remnant from i810 support.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Now that the stolen memory does not also steal entries from the GTT, we
can use all the memory the BIOS set aside for the GPU.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Support more than just the "Misc Control" part of the northbridges.
Support more flags by turning "gart_supported" into a single bit flag
that is stored in a flags member. Clean up related code by using a set
of functions (amd_nb_num(), amd_nb_has_feature() and node_to_amd_nb())
instead of accessing the NB data structures directly. Reorder the
initialization code and put the GART flush words caching in a separate
function.
Signed-off-by: Hans Rosenfeld <hans.rosenfeld@amd.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Not only the naming of the files was confusing, it was even more so for
the function and variable names.
Renamed the K8 NB and NUMA stuff that is also used on other AMD
platforms. This also renames the CONFIG_K8_NUMA option to
CONFIG_AMD_NUMA and the related file k8topology_64.c to
amdtopology_64.c. No functional changes intended.
Signed-off-by: Hans Rosenfeld <hans.rosenfeld@amd.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The big kernel lock has been removed from all these files at some point,
leaving only the #include.
Remove this too as a cleanup.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The fix in commit 6b4e81db25 ("i8k: Tell gcc that *regs gets
clobbered") to work around the gcc miscompiling i8k.c to add "+m
(*regs)" caused register pressure problems and a build failure.
Changing the 'asm' statement to 'asm volatile' instead should prevent
that and works around the gcc bug as well, so we can remove the "+m".
[ Background on the gcc bug: a memory clobber fails to mark the function
the asm resides in as non-pure (aka "__attribute__((const))"), so if
the function does nothing else that triggers the non-pure logic, gcc
will think that that function has no side effects at all. As a result,
callers will be mis-compiled.
Adding the "+m" made gcc see that it's not a pure function, and so
does "asm volatile". The problem was never really the need to mark
"*regs" as changed, since the memory clobber did that part - the
problem was just a bug in the gcc "pure" function analysis - Linus ]
Signed-off-by: Jim Bos <jim876@xs4all.nl>
Acked-by: Jakub Jelinek <jakub@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
More recent GCC caused the i8k driver to stop working, on Slackware
compiler was upgraded from gcc-4.4.4 to gcc-4.5.1 after which it didn't
work anymore, meaning the driver didn't load or gave total nonsensical
output.
As it turned out the asm(..) statement forgot to mention it modifies the
*regs variable.
Credits to Andi Kleen and Andreas Schwab for providing the fix.
Signed-off-by: Jim Bos <jim876@xs4all.nl>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Over time, block layer has accumulated a set of APIs dealing with bdev
open, close, claim and release.
* blkdev_get/put() are the primary open and close functions.
* bd_claim/release() deal with exclusive open.
* open/close_bdev_exclusive() are combination of open and claim and
the other way around, respectively.
* bd_link/unlink_disk_holder() to create and remove holder/slave
symlinks.
* open_by_devnum() wraps bdget() + blkdev_get().
The interface is a bit confusing and the decoupling of open and claim
makes it impossible to properly guarantee exclusive access as
in-kernel open + claim sequence can disturb the existing exclusive
open even before the block layer knows the current open if for another
exclusive access. Reorganize the interface such that,
* blkdev_get() is extended to include exclusive access management.
@holder argument is added and, if is @FMODE_EXCL specified, it will
gain exclusive access atomically w.r.t. other exclusive accesses.
* blkdev_put() is similarly extended. It now takes @mode argument and
if @FMODE_EXCL is set, it releases an exclusive access. Also, when
the last exclusive claim is released, the holder/slave symlinks are
removed automatically.
* bd_claim/release() and close_bdev_exclusive() are no longer
necessary and either made static or removed.
* bd_link_disk_holder() remains the same but bd_unlink_disk_holder()
is no longer necessary and removed.
* open_bdev_exclusive() becomes a simple wrapper around lookup_bdev()
and blkdev_get(). It also has an unexpected extra bdev_read_only()
test which probably should be moved into blkdev_get().
* open_by_devnum() is modified to take @holder argument and pass it to
blkdev_get().
Most of bdev open/close operations are unified into blkdev_get/put()
and most exclusive accesses are tested atomically at the open time (as
it should). This cleans up code and removes some, both valid and
invalid, but unnecessary all the same, corner cases.
open_bdev_exclusive() and open_by_devnum() can use further cleanup -
rename to blkdev_get_by_path() and blkdev_get_by_devt() and drop
special features. Well, let's leave them for another day.
Most conversions are straight-forward. drbd conversion is a bit more
involved as there was some reordering, but the logic should stay the
same.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Neil Brown <neilb@suse.de>
Acked-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Peter Osterlund <petero2@telia.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <joel.becker@oracle.com>
Cc: Alex Elder <aelder@sgi.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: dm-devel@redhat.com
Cc: drbd-dev@lists.linbit.com
Cc: Leo Chen <leochen@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Cc: Joern Engel <joern@logfs.org>
Cc: reiserfs-devel@vger.kernel.org
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
n_gsm: Fix length handling
n_gsm: Copy n2 over when configuring via ioctl interface
serial: bfin_5xx: grab port lock before making port termios changes
serial: bfin_5xx: disable CON_PRINTBUFFER for consoles
serial: bfin_5xx: remove redundant SSYNC to improve TX speed
serial: bfin_5xx: always include DMA headers
vcs: make proper usage of the poll flags
amiserial: Remove unused variable icount
8250: Fix tcsetattr to avoid ioctl(TIOCMIWAIT) hang
tty_ldisc: Fix BUG() on hangup
TTY: restore tty_ldisc_wait_idle
SERIAL: blacklist si3052 chip
drivers/serial/bfin_5xx.c: Fix line continuation defects
tty: prevent DOS in the flush_to_ldisc
8250: add support for Kouwell KW-L221N-2
nozomi: Fix warning from the previous TIOCGCOUNT changes
tty: fix warning in synclink driver
tty: Fix formatting in tty.h
tty: the development tree is now done in git
drivers/char/amiserial.c: In function ?rs_ioctl?:
drivers/char/amiserial.c:1302: warning: unused variable ?icount?
commit 0587102cf9 ("tty: icount changeover for
other main devices") removed the users, but not the actual variable.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
During builds I see the following warning -
CC [M] drivers/char/pcmcia/synclink_cs.o
drivers/char/pcmcia/synclink_cs.c:2194: warning: ‘mgslpc_get_icount’ defined but not used
The function is a callback meant to be assigned to get_icount (added during 0587102cf).
Fix accordingly.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
I'm assuming it's not intended to instantly change the error code
from -ENODEV to -EIO, is it?
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Acked-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
During builds I see the following warning -
CC [M] drivers/char/pcmcia/synclink_cs.o
drivers/char/pcmcia/synclink_cs.c:2194: warning: ‘mgslpc_get_icount’ defined but not used
The function is a callback meant to be assigned to get_icount (added during 0587102cf).
Fix accordingly.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel:
drm/i915: Fix LVDS fixed-mode regression from 219adae1
drm/i915/ringbuffer: Use the HEAD auto-reporting mechanism
drm/i915: Avoid might_fault during pwrite whilst holding our mutex
agp/intel: fix cache control for sandybridge
agp/intel: restore cache behavior on sandybridge
drm/i915; Don't apply Ironlake FDI clock workaround to Sandybridge
drm/i915: Fix KMS regression on Sandybridge/CPT
i915: reprogram power monitoring registers on resume
drm/i915: SNB BLT workaround
drm/i915: Fix the graphics frequency clamping at init and when IPS is active.
drm/i915: Allow powersave modparam to be adjusted at runtime.
drm/i915: Apply big hammer to serialise buffer access between rings
drm/i915: opregion_setup: iounmap correct address
drm/i915: Flush read-only buffers from the active list upon idle as well
i915: signedness bug in check_overlay_src()
drm/i915: Fix typo from "Enable DisplayPort Audio"
The autogenerated files (consolemap_deftbl.c and defkeymap.c) need to
be ignored by git, so move the .gitignore file that was doing it to the
properly location now that the files have moved as well.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The vt and other related code is moved into the drivers/tty/vt directory.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The tty code should be in its own subdirectory and not in the char
driver with all of the cruft that is currently there.
Based on work done by Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is broken from 97ef1bdd0b.
Let's set the correct bit for LLC+MLC and LLC only.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This restores cache behavior for default AGP_USER_MEMORY as
uncached, and leave default AGP_USER_CACHED_MEMORY as LLC only.
I've seen different cache behavior on one sandybridge desktop CPU vs.
another mobile CPU. Until we figure out how to detect the real cache
config, restore back to the original behavior now.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This restores cache behavior for default AGP_USER_MEMORY as
uncached, and leave default AGP_USER_CACHED_MEMORY as LLC only.
I've seen different cache behavior on one sandybridge desktop CPU vs.
another mobile CPU. Until we figure out how to detect the real cache
config, restore back to the original behavior now.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This is broken from 97ef1bdd0b.
Let's set the correct bit for LLC+MLC and LLC only.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
... and trying to set the bit is ineffectual.
Fixes the regression from e380f60 which detected that we were trying to
do undefined operations on the I830_GMCH_CTRL.
Reported-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
While auditing all tasklist_lock read_lock sites I stumbled over the
following call chain:
audit_prepare_user_tty()
read_lock(&tasklist_lock);
tty_audit_push_task();
mutex_lock(&buf->mutex);
--> buf->mutex is locked with preemption disabled.
Solve this by acquiring a reference to the task struct under
rcu_read_lock and call tty_audit_push_task outside of the preempt
disabled region.
Move all code which needs to be protected by sighand lock into
tty_audit_push_task() and use lock/unlock_sighand as we do not hold
tasklist_lock.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Eric Paris <eparis@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Greg Kroah-Hartman
Amit Shah
Linus Torvalds
Axel Lin
Grant Likely
Rob Herring
Dave Airlie
Russell King
Florian Mickler
Chris Wilson
John Stultz
Jarod Wilson
Alan Cox
Julia Lawall
Mike Frysinger
James Morris
Stefan Berger
Corey Minyard
Stephen Kitt
Matt Turner
Thomas Gleixner
Richard Cochran
Torben Hohn
Olof Johansson
Rajiv Andrade
Jamie Iles
David Rientjes
Oswald Buddenhagen
Andrew Morton
Andres Salomon
Seiji Aguchi
Len Brown
Lin Ming
Dave Airlie
Benjamin Herrenschmidt
Alexey Dobriyan
Ingo Molnar
Don Zickus
Herbert Xu
Ahmed S. Darwish
Tejun Heo
Christoph Lameter
Zhao Yakui
Namhyung Kim
Takashi Iwai
Daniel Walker
Matthew Garrett
Joe Perches
Mimi Zohar
Jens Axboe
Jiri Slaby
Daniel Vetter
Hans Rosenfeld
Arnd Bergmann
Jim Bos
Geert Uytterhoeven
Nicolas Kaiser
Zhenyu Wang