[ Upstream commit d899aa6684 ]
MSI remapping is disabled by VMD driver for Intel's Icelake and
newer systems in order to improve performance by setting
VMCONFIG_MSI_REMAP. By design VMCONFIG_MSI_REMAP register is cleared
by firmware during boot. The same register gets cleared when system
is put in S3 power state. VMD driver needs to set this register again
in order to avoid interrupt issues with devices behind VMD if MSI
remapping was disabled before.
Link: https://lore.kernel.org/r/20221109142652.450998-1-nirmal.patel@linux.intel.com
Fixes: ee81ee84f8 ("PCI: vmd: Disable MSI-X remapping when possible")
Signed-off-by: Nirmal Patel <nirmal.patel@linux.intel.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Francisco Munoz <francisco.munoz.ruiz@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6acd25cc98 ]
The pci_epf_test_notifier function should be installed also if only
core_init_notifier is enabled. Fix the current logic.
Link: https://lore.kernel.org/r/20220825090101.20474-1-hayashi.kunihiko@socionext.com
Fixes: 5e50ee27d4 ("PCI: pci-epf-test: Add support to defer core initialization")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Acked-by: Om Prakash Singh <omp@nvidia.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6611036128 ]
commit aeaa0bfe89 ("PCI: dwc: Move N_FTS setup to common setup")
incorrectly uses pci->link_gen in deriving the index to the
n_fts[] array also introducing the issue of accessing beyond the
boundaries of array for greater than Gen-2 speeds. This change fixes
that issue.
Link: https://lore.kernel.org/r/20220926111923.22487-1-vidyas@nvidia.com
Fixes: aeaa0bfe89 ("PCI: dwc: Move N_FTS setup to common setup")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0e32818397 upstream.
When pci_assign_resource() is unable to assign resources to a BAR, it uses
pci_revert_fw_address() to fall back to a firmware assignment (if any).
Previously pci_revert_fw_address() assumed all addresses could reach the
device, but this is not true if the device is below a bridge that only
forwards addresses within its windows.
This problem was observed on a Tyan Tomcat IV S1564D system where the BIOS
did not assign valid addresses to several bridges and USB devices:
pci 0000:00:11.0: PCI-to-PCIe bridge to [bus 01-ff]
pci 0000:00:11.0: bridge window [io 0xe000-0xefff]
pci 0000:01:00.0: PCIe Upstream Port to [bus 02-ff]
pci 0000:01:00.0: bridge window [io 0x0000-0x0fff] # unreachable
pci 0000:02:02.0: PCIe Downstream Port to [bus 05-ff]
pci 0000:02:02.0: bridge window [io 0x0000-0x0fff] # unreachable
pci 0000:05:00.0: PCIe-to-PCI bridge to [bus 06-ff]
pci 0000:05:00.0: bridge window [io 0x0000-0x0fff] # unreachable
pci 0000:06:08.0: USB UHCI 1.1
pci 0000:06:08.0: BAR 4: [io 0xfce0-0xfcff] # unreachable
pci 0000:06:08.1: USB UHCI 1.1
pci 0000:06:08.1: BAR 4: [io 0xfce0-0xfcff] # unreachable
pci 0000:06:08.0: can't claim BAR 4 [io 0xfce0-0xfcff]: no compatible bridge window
pci 0000:06:08.1: can't claim BAR 4 [io 0xfce0-0xfcff]: no compatible bridge window
During the first pass of assigning unassigned resources, there was not
enough I/O space available, so we couldn't assign the 06:08.0 BAR and
reverted to the firmware assignment (still unreachable). Reverting the
06:08.1 assignment failed because it conflicted with 06:08.0:
pci 0000:00:11.0: bridge window [io 0xe000-0xefff]
pci 0000:01:00.0: no space for bridge window [io size 0x2000]
pci 0000:02:02.0: no space for bridge window [io size 0x1000]
pci 0000:05:00.0: no space for bridge window [io size 0x1000]
pci 0000:06:08.0: BAR 4: no space for [io size 0x0020]
pci 0000:06:08.0: BAR 4: trying firmware assignment [io 0xfce0-0xfcff]
pci 0000:06:08.1: BAR 4: no space for [io size 0x0020]
pci 0000:06:08.1: BAR 4: trying firmware assignment [io 0xfce0-0xfcff]
pci 0000:06:08.1: BAR 4: [io 0xfce0-0xfcff] conflicts with 0000:06:08.0 [io 0xfce0-0xfcff]
A subsequent pass assigned valid bridge windows and a valid 06:08.1 BAR,
but left the 06:08.0 BAR alone, so the UHCI device was still unusable:
pci 0000:00:11.0: bridge window [io 0xe000-0xefff] released
pci 0000:00:11.0: bridge window [io 0x1000-0x2fff] # reassigned
pci 0000:01:00.0: bridge window [io 0x1000-0x2fff] # reassigned
pci 0000:02:02.0: bridge window [io 0x2000-0x2fff] # reassigned
pci 0000:05:00.0: bridge window [io 0x2000-0x2fff] # reassigned
pci 0000:06:08.0: BAR 4: assigned [io 0xfce0-0xfcff] # left alone
pci 0000:06:08.1: BAR 4: assigned [io 0x2000-0x201f]
...
uhci_hcd 0000:06:08.0: host system error, PCI problems?
uhci_hcd 0000:06:08.0: host controller process error, something bad happened!
uhci_hcd 0000:06:08.0: host controller halted, very bad!
uhci_hcd 0000:06:08.0: HCRESET not completed yet!
uhci_hcd 0000:06:08.0: HC died; cleaning up
If the address assigned by firmware is not reachable because it's not
within upstream bridge windows, fail instead of assigning the unusable
address from firmware.
[bhelgaas: commit log, use pci_upstream_bridge()]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=16263
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2203012338460.46819@angie.orcam.me.uk
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2209211921250.29493@angie.orcam.me.uk
Fixes: 58c84eda07 ("PCI: fall back to original BIOS BAR addresses")
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v2.6.35+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit c968af565c which is
commit 8795e182b0 upstream.
It is reported to cause problems, so drop it from the stable trees for
now until it gets sorted out.
Link: https://lore.kernel.org/r/47b775c5-57fa-5edf-b59e-8a9041ffbee7@candelatech.com
Reported-by: Ben Greear <greearb@candelatech.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Pali Rohár <pali@kernel.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Yao Hongbo <yaohongbo@linux.alibaba.com>
Cc: Naveen Naidu <naveennaidu479@gmail.com>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bcdb6fd4f3 ]
Slot capabilities are currently not reported because emulated bridge does
not report the PCI_EXP_FLAGS_SLOT flag.
Set PCI_EXP_FLAGS_SLOT to let the kernel know that PCI_EXP_SLT* registers
are supported.
Move setting of PCI_EXP_SLTCTL register from "dynamic" pcie_conf_read
function to static buffer as it is only statically filled the
PCI_EXP_SLTSTA_PDS flag and dynamic read callback is not needed for this
register.
Set Presence State Bit to 1 since there is no support for unplugging the
card and there is currently no platform able to detect presence of a card -
in such a case the bit needs to be set to 1.
Finally correctly set Physical Slot Number to 1 since there is only one
port and zero value is reserved for ports within the same silicon as Root
Port which is not our case for Aardvark HW.
Link: https://lore.kernel.org/r/20220524132827.8837-3-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit afd306a65c ]
The Broadcom BCM5750x NICs may be multi-function devices. They do not
advertise ACS capability. Peer-to-peer transactions are not possible
between the individual functions, so it is safe to treat them as fully
isolated.
Add an ACS quirk for these devices so the functions can be in independent
IOMMU groups and attached individually to userspace applications using
VFIO.
Link: https://lore.kernel.org/r/1654796507-28610-1-git-send-email-michael.chan@broadcom.com
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0e43bb997 ]
Currently the Gen2 port in IPQ8074 will cause the system to hang as it
accesses DBI registers in qcom_pcie_init_2_3_3(), and those are only
accesible after phy_power_on().
Move the DBI read/writes to a new qcom_pcie_post_init_2_3_3(), which is
executed after phy_power_on().
Link: https://lore.kernel.org/r/20220623155004.688090-1-robimarko@gmail.com
Fixes: a0fd361db8 ("PCI: dwc: Move "dbi", "dbi2", and "addr_space" resource setup into common code")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: stable@vger.kernel.org # v5.11+
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e6ae05095 ]
Previously we iterated over AER stat *names*, e.g.,
aer_correctable_error_string[32], but the actual stat *counters* may not be
that large, e.g., pdev->aer_stats->dev_cor_errs[16], which means that we
printed junk in the sysfs stats files.
Iterate over the stat counter arrays instead of the names to avoid this
junk.
Also, added a build time check to make sure all
counters have entries in strings array.
Fixes: 0678e3109a ("PCI/AER: Simplify __aer_print_error()")
Link: https://lore.kernel.org/r/20220509181441.31884-1-mkhalfella@purestorage.com
Reported-by: Meeta Saggi <msaggi@purestorage.com>
Signed-off-by: Mohamed Khalfella <mkhalfella@purestorage.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Meeta Saggi <msaggi@purestorage.com>
Reviewed-by: Eric Badger <ebadger@purestorage.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6646e99bce ]
As part of Root Port interrupt handling, level-0 register is read first and
based on the bits set in that, corresponding level-1 registers are read for
further interrupt processing. Since both these values are currently read
into the same 'val' variable, checking level-0 bits the second time around
is happening on the 'val' variable value of level-1 register contents
instead of freshly reading the level-0 value again.
Fix by using different variables to store level-0 and level-1 registers
contents.
Link: https://lore.kernel.org/r/20220721142052.25971-11-vidyas@nvidia.com
Fixes: 56e15a238d ("PCI: tegra: Add Tegra194 PCIe support")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 38f897ae3d ]
We currently enable clocks BEFORE we write to PARF_PHY_CTRL reg to enable
clocks and resets. This causes the driver to never set to a ready state
with the error 'Phy link never came up'.
This is caused by the PHY clock getting enabled before setting the required
bits in the PARF regs.
A workaround for this was set but with this new discovery we can drop
the workaround and use a proper solution to the problem by just enabling
the clock only AFTER the PARF_PHY_CTRL bit is set.
This correctly sets up the PCIe link and makes it usable even when a
bootloader leaves the PCIe link in an undefined state.
Fixes: 82a823833f ("PCI: qcom: Add Qualcomm PCIe controller driver")
Link: https://lore.kernel.org/r/20220708222743.27019-1-ansuelsmth@gmail.com
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8795e182b0 ]
AER reporting is currently disabled in the DevCtl registers of all non Root
Port PCIe devices on systems using pcie_ports_native || host->native_aer,
disabling AER completely in such systems. This is because 2bd50dd800
("PCI: PCIe: Disable PCIe port services during port initialization"), added
a call to pci_disable_pcie_error_reporting() *after* the AER setup was
completed for the PCIe device tree.
Here a longer analysis about the current status of AER enabling /
disabling upon bootup provided by Bjorn:
pcie_portdrv_probe
pcie_port_device_register
get_port_device_capability
pci_disable_pcie_error_reporting
clear CERE NFERE FERE URRE # <-- disable for RP USP DSP
pcie_device_init
device_register # new AER service device
aer_probe
aer_enable_rootport # RP only
set_downstream_devices_error_reporting
set_device_error_reporting # self (RP)
if (RP || USP || DSP)
pci_enable_pcie_error_reporting
set CERE NFERE FERE URRE # <-- enable for RP
pci_walk_bus
set_device_error_reporting
if (RP || USP || DSP)
pci_enable_pcie_error_reporting
set CERE NFERE FERE URRE # <-- enable for USP DSP
In a typical Root Port -> Endpoint hierarchy, the above:
- Disables Error Reporting for the Root Port,
- Enables Error Reporting for the Root Port,
- Does NOT enable Error Reporting for the Endpoint because it is not a
Root Port or Switch Port.
In a deeper Root Port -> Upstream Switch Port -> Downstream Switch
Port -> Endpoint hierarchy:
- Disables Error Reporting for the Root Port,
- Enables Error Reporting for the Root Port,
- Enables Error Reporting for both Switch Ports,
- Does NOT enable Error Reporting for the Endpoint because it is not a
Root Port or Switch Port,
- Disables Error Reporting for the Switch Ports when pcie_portdrv_probe()
claims them. AER does not re-enable it because these are not Root
Ports.
Remove this call to pci_disable_pcie_error_reporting() from
get_port_device_capability(), leaving the already enabled AER configuration
intact. With this change, AER is enabled in the Root Port and the PCIe
switch upstream and downstream ports. Only the PCIe Endpoints don't have
AER enabled yet. A follow-up patch will take care of this Endpoint
enabling.
Fixes: 2bd50dd800 ("PCI: PCIe: Disable PCIe port services during port initialization")
Link: https://lore.kernel.org/r/20220125071820.2247260-3-sr@denx.de
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Yao Hongbo <yaohongbo@linux.alibaba.com>
Cc: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1bc2b7bfba ]
Unbinding an endpoint function from the endpoint controller shouldn't stop
the controller. This is especially a problem for multi-function endpoints
where other endpoints may still be active.
Don't stop the controller when unbinding one of its endpoints. Normally
the controller is stopped via configfs.
Fixes: 349e7a85b2 ("PCI: endpoint: functions: Add an EP function to test PCI")
Link: https://lore.kernel.org/r/20220622040924.113279-1-mie@igel.co.jp
Signed-off-by: Shunsuke Mie <mie@igel.co.jp>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec7b952f45 ]
If the "snps,enable-cdm-check" property exists, we should enable the CDM
check. But previously dw_pcie_setup() could exit before doing so if the
"num-lanes" property was absent or invalid.
Move the CDM enable earlier so we do it regardless of whether "num-lanes"
is present.
[bhelgaas: commit log]
Fixes: 07f123def7 ("PCI: dwc: Add support to enable CDM register check")
Link: https://lore.kernel.org/r/20220624143428.8334-7-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8161e9626b ]
If dw_pcie_ep_init() fails to perform any action after the EPC memory is
initialized and the MSI memory region is allocated, the latter parts won't
be undone thus causing a memory leak. Add a cleanup-on-error path to fix
these leaks.
[bhelgaas: commit log]
Fixes: 2fd0c9d966 ("PCI: designware-ep: Pre-allocate memory for MSI in dw_pcie_ep_init")
Link: https://lore.kernel.org/r/20220624143428.8334-6-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 777e7c3ab7 ]
We program the 64-bit ATU limit address (in PCIE_ATU_LIMIT/
PCIE_ATU_UPPER_LIMIT or PCIE_ATU_UNR_LOWER_LIMIT/PCIE_ATU_UNR_UPPER_LIMIT),
but in addition, the PCIE_ATU_INCREASE_REGION_SIZE bit must be set if the
upper 32 bits of the limit address differ from the upper 32 bits of the
base address (see [1,2]).
5b4cf0f653 ("PCI: dwc: Add upper limit address for outbound iATU") set
PCIE_ATU_INCREASE_REGION_SIZE, but only when the *size* was greater than
4GB. It did not set it when a smaller region crossed a 4GB boundary, e.g.,
[mem 0x0_f0000000-0x1_0fffffff].
Set PCIE_ATU_INCREASE_REGION_SIZE whenever PCIE_ATU_UPPER_LIMIT is
greater than PCIE_ATU_UPPER_BASE.
[1] DesignWare Cores PCI Express Controller Databook - DWC PCIe Root Port,
v5.40a, March 2019, fig.3-36, p.175
[2] DesignWare Cores PCI Express Controller Databook - DWC PCIe Root Port,
v5.40a, March 2019, fig.3-37, p.176
[bhelgaas: commit log]
Fixes: 5b4cf0f653 ("PCI: dwc: Add upper limit address for outbound iATU")
Link: https://lore.kernel.org/r/20220624143428.8334-5-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d60a2e281e ]
Some DWC-based controllers (e.g., pcie-al.c and pci-keystone.c, identified
by the fact that they override the default dw_child_pcie_ops) use their own
address translation approach instead of the DWC internal ATU (iATU). For
those controllers, skip disabling the iATU outbound windows.
[bhelgaas: commit log, update multiple window comment]
Fixes: 458ad06c4c ("PCI: dwc: Ensure all outbound ATU windows are reset")
Link: https://lore.kernel.org/r/20220624143428.8334-4-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1cf738f2b ]
dw_pcie_disable_atu() was introduced by f8aed6ec62 ("PCI: dwc:
designware: Add EP mode support") and supported only the viewport version
of the iATU CSRs.
DW PCIe IP cores v4.80a and newer also support unrolled iATU/eDMA space.
Callers of dw_pcie_disable_atu(), including pci_epc_ops.clear_bar(),
pci_epc_ops.unmap_addr(), and dw_pcie_setup_rc(), don't work correctly when
it is enabled.
Add dw_pcie_disable_atu() support for controllers with unrolled iATU CSRs
enabled.
[bhelgaas: commit log]
Fixes: f8aed6ec62 ("PCI: dwc: designware: Add EP mode support")
Link: https://lore.kernel.org/r/20220624143428.8334-3-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 113fa857b7 ]
It's logically correct to undo everything that was done when an error is
discovered or in the corresponding cleanup counterpart. Otherwise the host
controller will be left in an undetermined state. Since the link is set up
in the host_init method, deactivate it there in the cleanup-on-error block
and stop the link in the antagonistic routine - dw_pcie_host_deinit(). Link
deactivation is platform-specific and should be implemented in
dw_pcie_ops.stop_link().
Fixes: 886a9c1347 ("PCI: dwc: Move link handling into common code")
Link: https://lore.kernel.org/r/20220624143428.8334-2-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b80892ca02 ]
No driver is left using the external pgmap refcount, so remove the
code to support it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20211028151017.50234-1-hch@lst.de
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf038503d5 ]
of_get_child_by_name() returns a node pointer with refcount incremented, so
we should use of_node_put() on it when we don't need it anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 814cceebba ("PCI: mediatek-gen3: Add INTx support")
Link: https://lore.kernel.org/r/20220601041259.56185-1-linmq006@gmail.com
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Miles Chen <miles.chen@mediatek.com>
Acked-by: Jianjun Wang <jianjun.wang@mediatek.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8fbd344a5 ]
pm_runtime_enable() will increase power disable depth. If
dw_pcie_ep_init() fails, we should use pm_runtime_disable() to balance it
with pm_runtime_enable().
Add missing pm_runtime_disable() for tegra_pcie_config_ep().
Fixes: c57247f940 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194")
Link: https://lore.kernel.org/r/20220602031910.55859-1-linmq006@gmail.com
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f030304fde ]
of_get_next_child() returns a node pointer with refcount incremented, so we
should use of_node_put() on it when we don't need it anymore.
mc_pcie_init_irq_domains() only calls of_node_put() in the normal path,
missing it in some error paths. Add missing of_node_put() to avoid
refcount leak.
Fixes: 6f15a9c9f9 ("PCI: microchip: Add Microchip PolarFire PCIe controller driver")
Link: https://lore.kernel.org/r/20220605055123.59127-1-linmq006@gmail.com
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a2bad844a6 upstream.
According to Dexuan, the hypervisor folks beleive that multi-msi
allocations are not correct. compose_msi_msg() will allocate multi-msi
one by one. However, multi-msi is a block of related MSIs, with alignment
requirements. In order for the hypervisor to allocate properly aligned
and consecutive entries in the IOMMU Interrupt Remapping Table, there
should be a single mapping request that requests all of the multi-msi
vectors in one shot.
Dexuan suggests detecting the multi-msi case and composing a single
request related to the first MSI. Then for the other MSIs in the same
block, use the cached information. This appears to be viable, so do it.
5.15 backport - add hv_msi_get_int_vector helper function. Fixed merge
conflict due to delivery_mode name change (APIC_DELIVERY_MODE_FIXED
is the value given to DELIVERY_MODE on x86). Removed unused variable
in hv_compose_msi_msg. Fixed reference to msi_desc->pci to point to
the same is_msix variable.
Suggested-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Tested-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/1652282599-21643-1-git-send-email-quic_jhugo@quicinc.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Carl Vanderlip <quic_carlv@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4b77778ec upstream.
Currently if compose_msi_msg() is called multiple times, it will free any
previous IRTE allocation, and generate a new allocation. While nothing
prevents this from occurring, it is extraneous when Linux could just reuse
the existing allocation and avoid a bunch of overhead.
However, when future IRTE allocations operate on blocks of MSIs instead of
a single line, freeing the allocation will impact all of the lines. This
could cause an issue where an allocation of N MSIs occurs, then some of
the lines are retargeted, and finally the allocation is freed/reallocated.
The freeing of the allocation removes all of the configuration for the
entire block, which requires all the lines to be retargeted, which might
not happen since some lines might already be unmasked/active.
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Tested-by: Dexuan Cui <decui@microsoft.com>
Tested-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/1652282582-21595-1-git-send-email-quic_jhugo@quicinc.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Carl Vanderlip <quic_carlv@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 455880dfe2 upstream.
In the multi-MSI case, hv_arch_irq_unmask() will only operate on the first
MSI of the N allocated. This is because only the first msi_desc is cached
and it is shared by all the MSIs of the multi-MSI block. This means that
hv_arch_irq_unmask() gets the correct address, but the wrong data (always
0).
This can break MSIs.
Lets assume MSI0 is vector 34 on CPU0, and MSI1 is vector 33 on CPU0.
hv_arch_irq_unmask() is called on MSI0. It uses a hypercall to configure
the MSI address and data (0) to vector 34 of CPU0. This is correct. Then
hv_arch_irq_unmask is called on MSI1. It uses another hypercall to
configure the MSI address and data (0) to vector 33 of CPU0. This is
wrong, and results in both MSI0 and MSI1 being routed to vector 33. Linux
will observe extra instances of MSI1 and no instances of MSI0 despite the
endpoint device behaving correctly.
For the multi-MSI case, we need unique address and data info for each MSI,
but the cached msi_desc does not provide that. However, that information
can be gotten from the int_desc cached in the chip_data by
compose_msi_msg(). Fix the multi-MSI case to use that cached information
instead. Since hv_set_msi_entry_from_desc() is no longer applicable,
remove it.
5.15 backport - no changes to code, but merge conflict due to refactor.
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/1651068453-29588-1-git-send-email-quic_jhugo@quicinc.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Carl Vanderlip <quic_carlv@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08e61e861a upstream.
If the allocation of multiple MSI vectors for multi-MSI fails in the core
PCI framework, the framework will retry the allocation as a single MSI
vector, assuming that meets the min_vecs specified by the requesting
driver.
Hyper-V advertises that multi-MSI is supported, but reuses the VECTOR
domain to implement that for x86. The VECTOR domain does not support
multi-MSI, so the alloc will always fail and fallback to a single MSI
allocation.
In short, Hyper-V advertises a capability it does not implement.
Hyper-V can support multi-MSI because it coordinates with the hypervisor
to map the MSIs in the IOMMU's interrupt remapper, which is something the
VECTOR domain does not have. Therefore the fix is simple - copy what the
x86 IOMMU drivers (AMD/Intel-IR) do by removing
X86_IRQ_ALLOC_CONTIGUOUS_VECTORS after calling the VECTOR domain's
pci_msi_prepare().
5.15 backport - adds the hv_msi_prepare wrapper function
Fixes: 4daace0d8c ("PCI: hv: Add paravirtual PCI front-end for Microsoft Hyper-V VMs")
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Link: https://lore.kernel.org/r/1649856981-14649-1-git-send-email-quic_jhugo@quicinc.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Carl Vanderlip <quic_carlv@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ea401499e9 ]
Stuart Hayes reports that an error handled by DPC at a Root Port results
in pciehp gratuitously bringing down a subordinate hotplug port:
RP -- UP -- DP -- UP -- DP (hotplug) -- EP
pciehp brings the slot down because the Link to the Endpoint goes down.
That is caused by a Hot Reset being propagated as a result of DPC.
Per PCIe Base Spec 5.0, section 6.6.1 "Conventional Reset":
For a Switch, the following must cause a hot reset to be sent on all
Downstream Ports: [...]
* The Data Link Layer of the Upstream Port reporting DL_Down status.
In Switches that support Link speeds greater than 5.0 GT/s, the
Upstream Port must direct the LTSSM of each Downstream Port to the
Hot Reset state, but not hold the LTSSMs in that state. This permits
each Downstream Port to begin Link training immediately after its
hot reset completes. This behavior is recommended for all Switches.
* Receiving a hot reset on the Upstream Port.
Once DPC recovers, pcie_do_recovery() walks down the hierarchy and
invokes pcie_portdrv_slot_reset() to restore each port's config space.
At that point, a hotplug interrupt is signaled per PCIe Base Spec r5.0,
section 6.7.3.4 "Software Notification of Hot-Plug Events":
If the Port is enabled for edge-triggered interrupt signaling using
MSI or MSI-X, an interrupt message must be sent every time the logical
AND of the following conditions transitions from FALSE to TRUE: [...]
* The Hot-Plug Interrupt Enable bit in the Slot Control register is
set to 1b.
* At least one hot-plug event status bit in the Slot Status register
and its associated enable bit in the Slot Control register are both
set to 1b.
Prevent pciehp from gratuitously bringing down the slot by clearing the
error-induced Data Link Layer State Changed event before restoring
config space. Afterwards, check whether the link has unexpectedly
failed to retrain and synthesize a DLLSC event if so.
Allow each pcie_port_service_driver (one of them being pciehp) to define
a slot_reset callback and re-use the existing pm_iter() function to
iterate over the callbacks.
Thereby, the Endpoint driver remains bound throughout error recovery and
may restore the device to working state.
Surprise removal during error recovery is detected through a Presence
Detect Changed event. The hotplug port is expected to not signal that
event as a result of a Hot Reset.
The issue isn't DPC-specific, it also occurs when an error is handled by
AER through aer_root_reset(). So while the issue was noticed only now,
it's been around since 2006 when AER support was first introduced.
[bhelgaas: drop PCI_ERROR_RECOVERY Kconfig, split pm_iter() rename to
preparatory patch]
Link: https://lore.kernel.org/linux-pci/08c046b0-c9f2-3489-eeef-7e7aca435bb9@gmail.com/
Fixes: 6c2b374d74 ("PCI-Express AER implemetation: AER core and aerdriver")
Link: https://lore.kernel.org/r/251f4edcc04c14f873ff1c967bc686169cd07d2d.1627638184.git.lukas@wunner.de
Reported-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Tested-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v2.6.19+: ba952824e6c1: PCI/portdrv: Report reset for frozen channel
Cc: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fdf6a2f533 upstream.
Fix a clock imbalance introduced by ed8cc3b1fc ("PCI: qcom: Add support
for SDM845 PCIe controller"), which enables the pipe clock both in init()
and in post_init() but only disables in post_deinit().
Note that the pipe clock was also never disabled in the init() error
paths and that enabling the clock before powering up the PHY looks
questionable.
Link: https://lore.kernel.org/r/20220401133351.10113-1-johan+linaro@kernel.org
Fixes: ed8cc3b1fc ("PCI: qcom: Add support for SDM845 PCIe controller")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: stable@vger.kernel.org # 5.6
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87d83b96c8 upstream.
Drop the leftover pm_runtime_disable() calls from the late probe error
paths that would, for example, prevent runtime PM from being reenabled
after a probe deferral.
Link: https://lore.kernel.org/r/20220401133854.10421-2-johan+linaro@kernel.org
Fixes: 6e5da6f7d8 ("PCI: qcom: Fix error handling in runtime PM support")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: stable@vger.kernel.org # 4.20
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12068bb346 upstream.
92597f97a4 ("PCI/PM: Avoid putting Elo i2 PCIe Ports in D3cold") omitted
braces around the new Elo i2 entry, so it overwrote the existing Gigabyte
X299 entry. Add the appropriate braces.
Found by:
$ make W=1 drivers/pci/pci.o
CC drivers/pci/pci.o
drivers/pci/pci.c:2974:12: error: initialized field overwritten [-Werror=override-init]
2974 | .ident = "Elo i2",
| ^~~~~~~~
Link: https://lore.kernel.org/r/20220526221258.GA409855@bhelgaas
Fixes: 92597f97a4 ("PCI/PM: Avoid putting Elo i2 PCIe Ports in D3cold")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v5.15+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7013654af6 ]
Clear the MSI bit in ISTATUS_LOCAL register after reading it, but
before reading and handling individual MSI bits from the ISTATUS_MSI
register. This avoids a potential race where new MSI bits may be set
on the ISTATUS_MSI register after it was read and be missed when the
MSI bit in the ISTATUS_LOCAL register is cleared.
ISTATUS_LOCAL is a read/write/clear register; the register's bits
are set when the corresponding interrupt source is activated. Each
source is independent and thus multiple sources may be active
simultaneously. The processor can monitor and clear status
bits. If one or more ISTATUS_LOCAL interrupt sources are active,
the RootPort issues an interrupt towards the processor (on
the AXI domain). Bit 28 of this register reports an MSI has been
received by the RootPort.
ISTATUS_MSI is a read/write/clear register. Bits 31-0 are asserted
when an MSI with message number 31-0 is received by the RootPort.
The processor must monitor and clear these bits.
Effectively, Bit 28 of ISTATUS_LOCAL informs the processor that
an MSI has arrived at the RootPort and ISTATUS_MSI informs the
processor which MSI (in the range 0 - 31) needs handling.
Reported by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/linux-pci/20220127202000.GA126335@bhelgaas/
Link: https://lore.kernel.org/r/20220517141622.145581-1-daire.mcnamara@microchip.com
Fixes: 6f15a9c9f9 ("PCI: microchip: Add Microchip PolarFire PCIe controller driver")
Signed-off-by: Daire McNamara <daire.mcnamara@microchip.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 203926da2b ]
When a Root Port or Root Complex Event Collector receives an error Message
e.g., ERR_COR, it sets PCI_ERR_ROOT_COR_RCV in the Root Error Status
register and logs the Requester ID in the Error Source Identification
register. If it receives a second ERR_COR Message before software clears
PCI_ERR_ROOT_COR_RCV, hardware sets PCI_ERR_ROOT_MULTI_COR_RCV and the
Requester ID is lost.
In the following scenario, PCI_ERR_ROOT_MULTI_COR_RCV was never cleared:
- hardware receives ERR_COR message
- hardware sets PCI_ERR_ROOT_COR_RCV
- aer_irq() entered
- aer_irq(): status = pci_read_config_dword(PCI_ERR_ROOT_STATUS)
- aer_irq(): now status == PCI_ERR_ROOT_COR_RCV
- hardware receives second ERR_COR message
- hardware sets PCI_ERR_ROOT_MULTI_COR_RCV
- aer_irq(): pci_write_config_dword(PCI_ERR_ROOT_STATUS, status)
- PCI_ERR_ROOT_COR_RCV is cleared; PCI_ERR_ROOT_MULTI_COR_RCV is set
- aer_irq() entered again
- aer_irq(): status = pci_read_config_dword(PCI_ERR_ROOT_STATUS)
- aer_irq(): now status == PCI_ERR_ROOT_MULTI_COR_RCV
- aer_irq() exits because PCI_ERR_ROOT_COR_RCV not set
- PCI_ERR_ROOT_MULTI_COR_RCV is still set
The same problem occurred with ERR_NONFATAL/ERR_FATAL Messages and
PCI_ERR_ROOT_UNCOR_RCV and PCI_ERR_ROOT_MULTI_UNCOR_RCV.
Fix the problem by queueing an AER event and clearing the Root Error Status
bits when any of these bits are set:
PCI_ERR_ROOT_COR_RCV
PCI_ERR_ROOT_UNCOR_RCV
PCI_ERR_ROOT_MULTI_COR_RCV
PCI_ERR_ROOT_MULTI_UNCOR_RCV
See the bugzilla link for details from Eric about how to reproduce this
problem.
[bhelgaas: commit log, move repro details to bugzilla]
Fixes: e167bfcaa4 ("PCI: aerdrv: remove magical ROOT_ERR_STATUS_MASKS")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215992
Link: https://lore.kernel.org/r/20220418150237.1021519-1-sathyanarayanan.kuppuswamy@linux.intel.com
Reported-by: Eric Badger <ebadger@purestorage.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6809941c1 ]
According to the PCIe standard the PERST# signal (reset-gpio in
fsl,imx* compatible dts) should be kept asserted for at least 100 usec
before the PCIe refclock is stable, should be kept asserted for at
least 100 msec after the power rails are stable and the host should wait
at least 100 msec after it is de-asserted before accessing the
configuration space of any attached device.
From PCIe CEM r2.0, sec 2.6.2
T-PVPERL: Power stable to PERST# inactive - 100 msec
T-PERST-CLK: REFCLK stable before PERST# inactive - 100 usec.
From PCIe r5.0, sec 6.6.1
With a Downstream Port that does not support Link speeds greater than
5.0 GT/s, software must wait a minimum of 100 ms before sending a
Configuration Request to the device immediately below that Port.
Failure to do so could prevent PCIe devices to be working correctly,
and this was experienced with real devices.
Move reset assert to imx6_pcie_assert_core_reset(), this way we ensure
that PERST# is asserted before enabling any clock, move de-assert to the
end of imx6_pcie_deassert_core_reset() after the clock is enabled and
deemed stable and add a new delay of 100 msec just afterward.
Link: https://lore.kernel.org/all/20220211152550.286821-1-francesco.dolcini@toradex.com
Link: https://lore.kernel.org/r/20220404081509.94356-1-francesco.dolcini@toradex.com
Fixes: bb38919ec5 ("PCI: imx6: Add support for i.MX6 PCIe controller")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 88557685cd ]
When dma_mapping_error() returns error because of no enough memory,
but dw_pcie_host_init() returns success, which will mislead the callers.
Link: https://lore.kernel.org/r/30170911-0e2f-98ce-9266-70465b9073e5@huawei.com
Fixes: 07940c369a ("PCI: dwc: Fix MSI page leakage in suspend/resume")
Signed-off-by: Jianrong Zhang <zhangjianrong5@huawei.com>
Signed-off-by: Jiantao Zhang <water.zhangjiantao@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 214e0d8fe4 ]
The of_find_compatible_node() function returns a node pointer with
refcount incremented, We should use of_node_put() on it when done
Add the missing of_node_put() to release the refcount.
Link: https://lore.kernel.org/r/20220309091953.5630-1-linmq006@gmail.com
Fixes: 87e8657ba9 ("PCI: mediatek: Add new method to get shared pcie-cfg base address")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Miles Chen <miles.chen@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 096950e230 ]
The ep->ob_region_map bitmap is a long and it has BITS_PER_LONG bits.
Link: https://lore.kernel.org/r/20220315065944.GB13572@kili
Fixes: cf590b0783 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0aa3a0937f ]
The ep->ob_region_map bitmap is a long and it has BITS_PER_LONG bits.
Link: https://lore.kernel.org/r/20220315065829.GA13572@kili
Fixes: 37dddf14f1 ("PCI: cadence: Add EndPoint Controller driver for Cadence PCIe controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dff6139015 ]
acpi_pci_bridge_d3(dev) returns "true" if "dev" is a hotplug bridge that
can handle hotplug events while in D3. Previously this meant either:
- "dev" has a _PS0 or _PR0 method (acpi_pci_power_manageable()), or
- The Root Port above "dev" has a _DSD with a "HotPlugSupportInD3"
property with value 1.
This did not consider _PRW, which tells us about wakeup GPEs (ACPI v6.4,
sec 7.3.13). Without a wakeup GPE, from an ACPI perspective the Root Port
has no way of generating wakeup signals, so hotplug events will be lost if
we use D3.
Similarly, it did not consider _S0W, which tells us the deepest D-state
from which a device can wake itself (sec 7.3.20). If _S0W tells us the
device cannot wake from D3, hotplug events will again be lost if we use D3.
Some platforms, e.g., AMD Yellow Carp, supply "HotPlugSupportInD3" without
_PRW or with an _S0W that says the Root Port cannot wake from D3. On those
platforms, we previously put bridges in D3hot, hotplug events were lost,
and hotplugged devices would not be recognized without manually rescanning.
Allow bridges to be put in D3 only if the Root Port can generate wakeup
GPEs (wakeup.flags.valid), it can wake from D3 (_S0W), AND it has the
"HotPlugSupportInD3" property.
Neither Windows 10 nor Windows 11 puts the bridge in D3 when the firmware
is configured this way, and this change aligns the handling of the
situation to be the same.
[bhelgaas: commit log, tidy "HotPlugSupportInD3" check and comment]
Link: https://uefi.org/htmlspecs/ACPI_Spec_6_4_html/07_Power_and_Performance_Mgmt/device-power-management-objects.html?highlight=s0w#s0w-s0-device-wake-state
Link: https://docs.microsoft.com/en-us/windows-hardware/drivers/pci/dsd-for-pcie-root-ports#identifying-pcie-root-ports-supporting-hot-plug-in-d3
Link: https://lore.kernel.org/r/20220401034003.3166-1-mario.limonciello@amd.com
Fixes: 26ad34d510 ("PCI / ACPI: Whitelist D3 for more PCIe hotplug ports")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a91ee0e9fc ]
The sysfs sriov_numvfs_store() path acquires the device lock before the
config space access lock:
sriov_numvfs_store
device_lock # A (1) acquire device lock
sriov_configure
vfio_pci_sriov_configure # (for example)
vfio_pci_core_sriov_configure
pci_disable_sriov
sriov_disable
pci_cfg_access_lock
pci_wait_cfg # B (4) wait for dev->block_cfg_access == 0
Previously, pci_dev_lock() acquired the config space access lock before the
device lock:
pci_dev_lock
pci_cfg_access_lock
dev->block_cfg_access = 1 # B (2) set dev->block_cfg_access = 1
device_lock # A (3) wait for device lock
Any path that uses pci_dev_lock(), e.g., pci_reset_function(), may
deadlock with sriov_numvfs_store() if the operations occur in the sequence
(1) (2) (3) (4).
Avoid the deadlock by reversing the order in pci_dev_lock() so it acquires
the device lock before the config space access lock, the same as the
sriov_numvfs_store() path.
[bhelgaas: combined and adapted commit log from Jay Zhou's independent
subsequent posting:
https://lore.kernel.org/r/20220404062539.1710-1-jianjay.zhou@huawei.com]
Link: https://lore.kernel.org/linux-pci/1583489997-17156-1-git-send-email-yangyicong@hisilicon.com/
Also-posted-by: Jay Zhou <jianjay.zhou@huawei.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a3b69dd0ad ]
This reverts commit 1571d67dc1.
This commit broke support for setting interrupt affinity. It looks like
that it is related to the chained IRQ handler. Revert this commit until
issue with setting interrupt affinity is fixed.
Fixes: 1571d67dc1 ("PCI: aardvark: Rewrite IRQ code to chained IRQ handler")
Link: https://lore.kernel.org/r/20220515125815.30157-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 92597f97a4 upstream.
If a Root Port on Elo i2 is put into D3cold and then back into D0, the
downstream device becomes permanently inaccessible, so add a bridge D3 DMI
quirk for that system.
This was exposed by 14858dcc3b ("PCI: Use pci_update_current_state() in
pci_enable_device_flags()"), but before that commit the Root Port in
question had never been put into D3cold for real due to a mismatch between
its power state retrieved from the PCI_PM_CTRL register (which was
accessible even though the platform firmware indicated that the port was in
D3cold) and the state of an ACPI power resource involved in its power
management.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=215715
Link: https://lore.kernel.org/r/11980172.O9o76ZdvQC@kreacher
Reported-by: Stefan Gottwald <gottwald@igel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v5.15+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92f4ffecc4 upstream.
Update the comment about what happens when link goes down after we have
checked for link-up. If a PIO request is done while link-down, we have
a serious problem.
Link: https://lore.kernel.org/r/20220110015018.26359-23-kabel@kernel.org
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c36ab437e upstream.
This function is now always used in driver remove method, drop the
__maybe_unused attribute.
Link: https://lore.kernel.org/r/20220110015018.26359-22-kabel@kernel.org
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit befa710001 upstream.
By default, all Legacy INTx interrupts are masked, so there is no need to
mask this interrupt during irq_map() callback.
Link: https://lore.kernel.org/r/20220110015018.26359-21-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b08e5b53d1 upstream.
Callback for irq_mask_ack() is the same as for irq_mask(). As there is no
special handling for irq_ack(), there is no need to define irq_mask_ack()
too.
Link: https://lore.kernel.org/r/20220110015018.26359-20-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 815bc31368 upstream.
Emulated root bridge currently provides only one Legacy INTA interrupt
which is used for reporting PCIe PME and ERR events and handled by kernel
PCIe PME and AER drivers.
Aardvark HW reports these PME and ERR events separately, so there is no
need to mix real INTA interrupt and emulated INTA interrupt for PCIe PME
and AER drivers.
Register a new advk-RP (as in Root Port) irq chip and a new irq domain
for emulated root bridge and use this new separate irq domain for
providing INTA interrupt from emulated root bridge for PME and ERR events.
The real INTA interrupt from real devices is now separate.
A custom map_irq callback function on PCI host bridge structure is used to
allocate IRQ mapping for emulated root bridge from new irq domain. Original
callback of_irq_parse_and_map_pci() is used for all other devices as before.
Link: https://lore.kernel.org/r/20220110015018.26359-19-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 273ddd86d6 upstream.
Enable aardvark PME interrupt unconditionally by unmasking it and read PME
requester ID to emulated bridge config space immediately after receiving
interrupt.
PME requester ID is stored in the PCIE_MSG_LOG_REG register, which contains
the last inbound message. So when new inbound message is received by HW
(including non-PM), the content in PCIE_MSG_LOG_REG register is replaced by
a new value.
PCIe specification mandates that subsequent PMEs are kept pending until the
PME Status Register bit is cleared by software by writing a 1b.
Support for masking/unmasking PME interrupt on emulated bridge via
PCI_EXP_RTCTL_PMEIE bit is now implemented only in emulated bridge config
space, to ensure that we do not miss any aardvark PME interrupt.
Reading of PCI_EXP_RTCAP and PCI_EXP_RTSTA registers is simplified as final
value is now always stored into emulated bridge config space by the
interrupt handler, so there is no need to implement support for these
registers in read_pcie callback.
Clearing of W1C bit PCI_EXP_RTSTA_PME is now also simplified as it is done
by pci-bridge-emul.c code for emulated bridge config space. So there is no
need to implement support for clearing this bit in write_pcie callback.
Link: https://lore.kernel.org/r/20220110015018.26359-18-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0fc75d8745 upstream.
Currently enabling PCI_EXP_RTSTA_PME bit in PCI_EXP_RTCTL register does
nothing. This is because PCIe PME driver expects to receive PCIe interrupt
defined in PCI_EXP_FLAGS_IRQ register, but aardvark hardware does not
trigger PCIe INTx/MSI interrupt for PME event, rather it triggers custom
aardvark interrupt which this driver is not processing yet.
Fix this issue by handling PME interrupt in advk_pcie_handle_int() and
chaining it to PCIe interrupt 0 with generic_handle_domain_irq() (since
aardvark sets PCI_EXP_FLAGS_IRQ to zero). With this change PCIe PME driver
finally starts receiving PME interrupt.
Link: https://lore.kernel.org/r/20220110015018.26359-17-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7122bcb332 upstream.
To optimize advk_pci_bridge_emul_pcie_conf_write() code, touch
PCIE_ISR0_REG and PCIE_ISR0_MASK_REG registers only when it is really
needed, when processing PCI_EXP_RTCTL_PMEIE and PCI_EXP_RTSTA_PME bits.
Link: https://lore.kernel.org/r/20220110015018.26359-16-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ebfefa396 upstream.
ERR interrupt is triggered when corresponding bit is unmasked in both ISR0
and PCI_EXP_DEVCTL registers. Unmasking ERR bits in PCI_EXP_DEVCTL register
is not enough. This means that currently the ERR interrupt is never
triggered.
Unmask ERR bits in ISR0 register at driver probe time. ERR interrupt is not
triggered until ERR bits are unmasked also in PCI_EXP_DEVCTL register,
which is done by AER driver. So it is safe to unconditionally unmask all
ERR bits in aardvark probe.
Aardvark HW sets PCI_ERR_ROOT_AER_IRQ to zero and when corresponding bits
in ISR0 and PCI_EXP_DEVCTL are enabled, the HW triggers a generic interrupt
on GIC. Chain this interrupt to PCIe interrupt 0 with
generic_handle_domain_irq() to allow processing of ERR interrupts.
Link: https://lore.kernel.org/r/20220110015018.26359-14-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 754e449889 upstream.
According to PCI 3.0 specification, sending both MSI and MSI-X interrupts
is done by DWORD memory write operation to doorbell message address. The
write operation for MSI has zero upper 16 bits and the MSI interrupt number
in the lower 16 bits, while the write operation for MSI-X contains a 32-bit
value from MSI-X table.
Since the driver only uses interrupt numbers from range 0..31, the upper
16 bits of the DWORD memory write operation to doorbell message address
are zero even for MSI-X interrupts. Thus we can enable MSI-X interrupts.
Testing proves that kernel can correctly receive MSI-X interrupts from PCIe
cards which supports both MSI and MSI-X interrupts.
Link: https://lore.kernel.org/r/20220110015018.26359-13-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46ad3dc417 upstream.
MSI address for receiving MSI interrupts needs to be correctly set before
enabling processing of MSI interrupts.
Move code for setting PCIE_MSI_ADDR_LOW_REG and PCIE_MSI_ADDR_HIGH_REG
from advk_pcie_init_msi_irq_domain() to advk_pcie_setup_hw(), before
enabling PCIE_CORE_CTRL2_MSI_ENABLE.
After this we can remove the now unused member msi_msg, which was used
only for MSI doorbell address. MSI address can be any address which cannot
be used to DMA to. So change it to the address of the main struct advk_pcie.
Link: https://lore.kernel.org/r/20220110015018.26359-12-kabel@kernel.org
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org # f21a8b1b68 ("PCI: aardvark: Move to MSI handling using generic MSI support")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e77d9c9069 upstream.
We should not unmask MSIs at setup, but only when kernel asks for them
to be unmasked.
At setup, mask all MSIs, and implement IRQ chip callbacks for masking
and unmasking particular MSIs.
Link: https://lore.kernel.org/r/20220110015018.26359-11-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4689c09163 upstream.
Refactor the masking of ISR0/1 Sources and unmasking of summary MSI interrupt
so that it corresponds to the comments:
- first mask all ISR0/1
- then unmask all MSIs
- then unmask summary MSI interrupt
Link: https://lore.kernel.org/r/20220110015018.26359-10-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 222af78532 upstream.
Use simple
dev_fwnode(dev)
instead of
struct device_node *node = dev->of_node;
of_node_to_fwnode(node)
especially since the node variable is not used elsewhere in the function.
Link: https://lore.kernel.org/r/20220110015018.26359-9-kabel@kernel.org
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26bcd54e4a upstream.
Make Aardvark's msi_domain_info structure into a private driver structure.
Domain info is same for every potential instatination of a controller.
Link: https://lore.kernel.org/r/20220110015018.26359-8-kabel@kernel.org
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c3cb8e5183 upstream.
In [1] it was agreed that we should use struct irq_chip as a global
static struct in the driver. Even though the structure currently
contains a dynamic member (parent_device), In [2] the plans to kill it
and make the structure completely static were set out.
Convert Aardvark's priv->msi_bottom_irq_chip and priv->msi_irq_chip to
static driver structure.
[1] https://lore.kernel.org/linux-pci/877dbcvngf.wl-maz@kernel.org/
[2] https://lore.kernel.org/linux-pci/874k6gvkhz.wl-maz@kernel.org/
Link: https://lore.kernel.org/r/20220110015018.26359-7-kabel@kernel.org
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51f96e287c upstream.
It is possible that we receive spurious INTx interrupt. Check for the
return value of generic_handle_domain_irq() when processing INTx IRQ.
Link: https://lore.kernel.org/r/20220110015018.26359-6-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1571d67dc1 upstream.
Rewrite the code to use irq_set_chained_handler_and_data() handler with
chained_irq_enter() and chained_irq_exit() processing instead of using
devm_request_irq().
advk_pcie_irq_handler() reads IRQ status bits and calls other functions
based on which bits are set. These functions then read its own IRQ status
bits and calls other aardvark functions based on these bits. Finally
generic_handle_domain_irq() with translated linux IRQ numbers are called.
Link: https://lore.kernel.org/r/20220110015018.26359-5-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fdbbe242c1 upstream.
Disable the PCIe PHY when unbinding driver. This should save some power.
Link: https://lore.kernel.org/r/20211130172913.9727-12-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 759dec2e3d upstream.
Disable link training circuit in driver unbind sequence. We want to
leave link training in the same state as it was before the driver was
probed.
Link: https://lore.kernel.org/r/20211130172913.9727-11-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f54391be8 upstream.
Put the PCIe card into reset by asserting PERST# signal when unbinding
driver. It doesn't make sense to leave the card working if it can't
communicate with the host. This should also save some power.
Link: https://lore.kernel.org/r/20211130172913.9727-10-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f040a17f5 upstream.
Free config space for emulated root bridge when unbinding driver to fix
memory leak. Do it after disabling and masking all interrupts, since
aardvark interrupt handler accesses config space of emulated root
bridge.
Link: https://lore.kernel.org/r/20211130172913.9727-9-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13bcdf07cb upstream.
Ensure that no interrupt can be triggered after driver unbind.
Link: https://lore.kernel.org/r/20211130172913.9727-8-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a46f2f6dd4 upstream.
Ensure that after driver unbind PCIe cards are not able to forward
memory and I/O requests in the upstream direction.
Link: https://lore.kernel.org/r/20211130172913.9727-7-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4ca7948e1 upstream.
Add two more comments into the advk_pcie_remove() method.
Link: https://lore.kernel.org/r/20211130172913.9727-6-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d8dc1f7cd upstream.
We already clear all the other interrupts (ISR0, ISR1, HOST_CTRL_INT).
Define a new macro PCIE_MSI_ALL_MASK and do the same clearing for MSIs,
to ensure that we don't start receiving spurious interrupts.
Use this new mask in advk_pcie_handle_msi();
Link: https://lore.kernel.org/r/20211130172913.9727-5-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ea673a8b3 upstream.
pci-bridge-emul driver already allocates buffer for capabilities up to the
PCI_EXP_SLTSTA2 register, but does not define bit access behavior for these
registers. Add these missing definitions.
Link: https://lore.kernel.org/r/20211130172913.9727-3-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9319230ac1 upstream.
The current assignment to the class_revision member
class_revision |= cpu_to_le32(PCI_CLASS_BRIDGE_PCI << 16);
can make the reader think that class is at high 16 bits of the member and
revision at low 16 bits.
In reality, class is at high 24 bits, but the class for PCI Bridge Normal
Decode is PCI_CLASS_BRIDGE_PCI << 8.
Change the assignment and add a comment to make this clearer.
Link: https://lore.kernel.org/r/20211130172913.9727-2-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8d21732475 ]
PCI pass-thru devices in a Hyper-V VM are represented as a VMBus
device and as a PCI device. The coherence of the VMbus device is
set based on the VMbus node in ACPI, but the PCI device has no
ACPI node and defaults to not hardware coherent. This results
in extra software coherence management overhead on ARM64 when
devices are hardware coherent.
Fix this by setting up the PCI host bus so that normal
PCI mechanisms will propagate the coherence of the VMbus
device to the PCI device. There's no effect on x86/x64 where
devices are always hardware coherent.
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Acked-by: Boqun Feng <boqun.feng@gmail.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/1648138492-2191-3-git-send-email-mikelley@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf8d87c076 ]
Fix a misused goto label jump since that can result in a memory leak.
Link: https://lore.kernel.org/r/17e7b9b9ee6.c6d9c6a02564.4545388417402742326@zohomail.com
Signed-off-by: Li Chen <lchen@ambarella.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f72d4757c ]
The Qualcomm PCI bridge device (Device ID 0x0110) found in chipsets such as
SM8450 does not set the Command Completed bit unless writes to the Slot
Command register change "Control" bits.
This results in timeouts like below:
pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2020 msec ago)
Add the device to the Command Completed quirk to mark commands "completed"
immediately unless they change the "Control" bits.
Link: https://lore.kernel.org/r/20220210145003.135907-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0b0b8b897 ]
Aardvark hardware supports Multi-MSI and MSI_FLAG_MULTI_PCI_MSI is already
set for the MSI chip. But when allocating MSI interrupt numbers for
Multi-MSI, the numbers need to be properly aligned, otherwise endpoint
devices send MSI interrupt with incorrect numbers.
Fix this issue by using function bitmap_find_free_region() instead of
bitmap_find_next_zero_area().
To ensure that aligned MSI interrupt numbers are used by endpoint devices,
we cannot use Linux virtual irq numbers (as they are random and not
properly aligned). Instead we need to use the aligned hwirq numbers.
This change fixes receiving MSI interrupts on Armada 3720 boards and
allows using NVMe disks which use Multi-MSI feature with 3 interrupts.
Without this NVMe disks freeze booting as linux nvme-core.c is waiting
60s for an interrupt.
Link: https://lore.kernel.org/r/20220110015018.26359-4-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1874b6d7ab upstream.
Commit 6dce5aa59e ("PCI: xgene: Use inbound resources for setup")
killed PCIe on my XGene-1 box (a Mustang board). The machine itself
is still alive, but half of its storage (over NVMe) is gone, and the
NVMe driver just times out.
Note that this machine boots with a device tree provided by the
UEFI firmware (2016 vintage), which could well be non conformant
with the spec, hence the breakage.
With the patch reverted, the box boots 5.17-rc8 with flying colors.
Link: https://lore.kernel.org/all/Yf2wTLjmcRj+AbDv@xps13.dannf
Link: https://lore.kernel.org/r/20220321104843.949645-2-maz@kernel.org
Fixes: 6dce5aa59e ("PCI: xgene: Use inbound resources for setup")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Cc: Rob Herring <robh@kernel.org>
Cc: Toan Le <toan@os.amperecomputing.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Krzysztof Wilczyński <kw@linux.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Stéphane Graber <stgraber@ubuntu.com>
Cc: dann frazier <dann.frazier@canonical.com>
[dannf: minor context adjustment]
Signed-off-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 92c45b63ce ]
For hardware that only supports 32-bit writes to PCI there is the
possibility of clearing RW1C (write-one-to-clear) bits. A rate-limited
messages was introduced by fb26592301, but rate-limiting is not the best
choice here. Some devices may not show the warnings they should if another
device has just produced a bunch of warnings. Also, the number of messages
can be a nuisance on devices which are otherwise working fine.
Change the ratelimit to a single warning per bus. This ensures no bus is
'starved' of emitting a warning and also that there isn't a continuous
stream of warnings. It would be preferable to have a warning per device,
but the pci_dev structure is not available here, and a lookup from devfn
would be far too slow.
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Fixes: fb26592301 ("PCI: Warn on possible RW1C corruption for sub-32 bit config writes")
Link: https://lore.kernel.org/r/20200806041455.11070-1-mark.tomlinson@alliedtelesis.co.nz
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 735f5ae49e ]
The emulated bridge returns incorrect value for PCI_EXP_RTSTA register
during readout in advk_pci_bridge_emul_pcie_conf_read() function: the
correct bit is BIT(16), but we are setting BIT(23), because the code
does
*value = (isr0 & PCIE_MSG_PM_PME_MASK) << 16
where
PCIE_MSG_PM_PME_MASK
is
BIT(7).
The code should probably have been something like
*value = (!!(isr0 & PCIE_MSG_PM_PME_MASK)) << 16,
but we are better of using an if() and using the proper macro for this
bit.
Link: https://lore.kernel.org/r/20220110015018.26359-15-kabel@kernel.org
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 805dfc18dd ]
In advk_pcie_handle_msi() it is expected that when bit i in the W1C
register PCIE_MSI_STATUS_REG is cleared, the PCIE_MSI_PAYLOAD_REG is
updated to contain the MSI number corresponding to index i.
Experiments show that this is not so, and instead PCIE_MSI_PAYLOAD_REG
always contains the number of the last received MSI, overall.
Do not read PCIE_MSI_PAYLOAD_REG register for determining MSI interrupt
number. Since Aardvark already forbids more than 32 interrupts and uses
own allocated hwirq numbers, the msi_idx already corresponds to the
received MSI number.
Link: https://lore.kernel.org/r/20220110015018.26359-3-kabel@kernel.org
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 825da4e9ce upstream.
Commit c7a75d0782 ("PCI: xgene: Fix IB window setup") tried to
fix the damages that 6dce5aa59e ("PCI: xgene: Use inbound resources
for setup") caused, but actually didn't improve anything for some
plarforms (at least Mustang and m400 are still broken).
Given that 6dce5aa59e has been reverted, revert this patch as well,
restoring the PCIe support on XGene to its pre-5.5, working state.
Link: https://lore.kernel.org/r/YjN8pT5e6/8cRohQ@xps13.dannf
Link: https://lore.kernel.org/r/20220321104843.949645-3-maz@kernel.org
Fixes: c7a75d0782 ("PCI: xgene: Fix IB window setup")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Cc: Rob Herring <robh@kernel.org>
Cc: Toan Le <toan@os.amperecomputing.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Krzysztof Wilczyński <kw@linux.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Stéphane Graber <stgraber@ubuntu.com>
Cc: dann frazier <dann.frazier@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92912b1751 upstream.
Writes to a Downstream Port's Slot Control register are PCIe hotplug
"commands." If the Port supports Command Completed events, software must
wait for a command to complete before writing to Slot Control again.
pcie_do_write_cmd() sets ctrl->cmd_busy when it writes to Slot Control. If
software notification is enabled, i.e., PCI_EXP_SLTCTL_HPIE and
PCI_EXP_SLTCTL_CCIE are set, ctrl->cmd_busy is cleared by pciehp_isr().
But when software notification is disabled, as it is when pcie_init()
powers off an empty slot, pcie_wait_cmd() uses pcie_poll_cmd() to poll for
command completion, and it neglects to clear ctrl->cmd_busy, which leads to
spurious timeouts:
pcieport 0000:00:03.0: pciehp: Timeout on hotplug command 0x01c0 (issued 2264 msec ago)
pcieport 0000:00:03.0: pciehp: Timeout on hotplug command 0x05c0 (issued 2288 msec ago)
Clear ctrl->cmd_busy in pcie_poll_cmd() when it detects a Command Completed
event (PCI_EXP_SLTSTA_CC).
[bhelgaas: commit log]
Fixes: a5dd4b4b05 ("PCI: pciehp: Wait for hotplug command completion where necessary")
Link: https://lore.kernel.org/r/20211111054258.7309-1-zhangliguang@linux.alibaba.com
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215143
Link: https://lore.kernel.org/r/20211126173309.GA12255@wunner.de
Signed-off-by: Liguang Zhang <zhangliguang@linux.alibaba.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f81f095e87 upstream.
The intention of commit 886a9c1347 ("PCI: dwc: Move link handling into
common code") was to standardize the behavior of link down as explained
in its commit log:
"The behavior for a link down was inconsistent as some drivers would fail
probe in that case while others succeed. Let's standardize this to
succeed as there are usecases where devices (and the link) appear later
even without hotplug. For example, a reconfigured FPGA device."
The pci-imx6 still fails to probe when the link is not present, which
causes the following warning:
imx6q-pcie 8ffc000.pcie: Phy link never came up
imx6q-pcie: probe of 8ffc000.pcie failed with error -110
------------[ cut here ]------------
WARNING: CPU: 0 PID: 30 at drivers/regulator/core.c:2257 _regulator_put.part.0+0x1b8/0x1dc
Modules linked in:
CPU: 0 PID: 30 Comm: kworker/u2:2 Not tainted 5.15.0-next-20211103 #1
Hardware name: Freescale i.MX6 SoloX (Device Tree)
Workqueue: events_unbound async_run_entry_fn
[<c0111730>] (unwind_backtrace) from [<c010bb74>] (show_stack+0x10/0x14)
[<c010bb74>] (show_stack) from [<c0f90290>] (dump_stack_lvl+0x58/0x70)
[<c0f90290>] (dump_stack_lvl) from [<c012631c>] (__warn+0xd4/0x154)
[<c012631c>] (__warn) from [<c0f87b00>] (warn_slowpath_fmt+0x74/0xa8)
[<c0f87b00>] (warn_slowpath_fmt) from [<c076b4bc>] (_regulator_put.part.0+0x1b8/0x1dc)
[<c076b4bc>] (_regulator_put.part.0) from [<c076b574>] (regulator_put+0x2c/0x3c)
[<c076b574>] (regulator_put) from [<c08c3740>] (release_nodes+0x50/0x178)
Fix this problem by ignoring the dw_pcie_wait_for_link() error like
it is done on the other dwc drivers.
Tested on imx6sx-sdb and imx6q-sabresd boards.
Link: https://lore.kernel.org/r/20220106103645.2790803-1-festevam@gmail.com
Fixes: 886a9c1347 ("PCI: dwc: Move link handling into common code")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a382c757ec upstream.
The fu740 PCIe core does not probe any devices on the SiFive Unmatched
board without this fix (or having U-Boot explicitly start the PCIe via
either boot-script or user command). The fix is to start the link at
2.5GT/s speeds and once the link is up then change the maximum speed back
to the default.
The U-Boot driver claims to set the link-speed to 2.5GT/s to get the probe
to work (and U-Boot does print link up at 2.5GT/s) in the following code:
https://source.denx.de/u-boot/u-boot/-/blob/master/drivers/pci/pcie_dw_sifive.c?id=v2022.01#L271
Link: https://lore.kernel.org/r/20220318152430.526320-1-ben.dooks@codethink.co.uk
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Dimitri John Ledkov <dimitri.ledkov@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3f1271b54e ]
There are enough VBIOS escapes without the proper workaround that some
users still hit this. Microsoft never productized ATS on Windows so OEM
platforms that were Windows-only didn't always validate ATS.
The advantages of ATS are not worth it compared to the potential
instabilities on harvested boards. Disable ATS on all Navi10 and Navi14
boards.
Symptoms include:
amdgpu 0000:07:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0007 address=0xffffc02000 flags=0x0000]
AMD-Vi: Event logged [IO_PAGE_FAULT device=07:00.0 domain=0x0007 address=0xffffc02000 flags=0x0000]
[drm:amdgpu_job_timedout [amdgpu]] *ERROR* ring sdma0 timeout, signaled seq=6047, emitted seq=6049
amdgpu 0000:07:00.0: amdgpu: GPU reset begin!
amdgpu 0000:07:00.0: amdgpu: GPU reset succeeded, trying to resume
amdgpu 0000:07:00.0: [drm:amdgpu_ring_test_helper [amdgpu]] *ERROR* ring sdma0 test failed (-110)
[drm:amdgpu_device_ip_resume_phase2 [amdgpu]] *ERROR* resume of IP block <sdma_v4_0> failed -110
amdgpu 0000:07:00.0: amdgpu: GPU reset(1) failed
Related commits:
e8946a53e2 ("PCI: Mark AMD Navi14 GPU ATS as broken")
a2da5d8cc0 ("PCI: Mark AMD Raven iGPU ATS as broken in some platforms")
45beb31d3a ("PCI: Mark AMD Navi10 GPU rev 0x00 ATS as broken")
5e89cd303e ("PCI: Mark AMD Navi14 GPU rev 0xc5 ATS as broken")
d28ca864c4 ("PCI: Mark AMD Stoney Radeon R7 GPU ATS as broken")
9b44b0b09d ("PCI: Mark AMD Stoney GPU ATS as broken")
[bhelgaas: add symptoms and related commits]
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1760
Link: https://lore.kernel.org/r/20220222160801.841643-1-alexander.deucher@amd.com
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ab34548c5 ]
Armada XP and new hardware supports access to DEVCAP2, DEVCTL2 and LNKCTL2
configuration registers of PCIe core via PCIE_CAP_PCIEXP. So export them
via emulated software root bridge.
Pre-XP hardware does not support these registers and returns zeros.
Link: https://lore.kernel.org/r/20211125124605.25915-16-pali@kernel.org
Fixes: 1f08673eef ("PCI: mvebu: Convert to PCI emulated bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 838ff44a39 ]
PME Status bit in Root Status Register (PCIE_RC_RTSTA_OFF) is read-only and
can be cleared only by writing 0b to the Interrupt Cause RW0C register
(PCIE_INT_CAUSE_OFF).
Link: https://lore.kernel.org/r/20211125124605.25915-15-pali@kernel.org
Fixes: 1f08673eef ("PCI: mvebu: Convert to PCI emulated bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d75404cc08 ]
Hardware supports PCIe Hot Reset via PCIE_CTRL_OFF register. Use it for
implementing PCI_BRIDGE_CTL_BUS_RESET bit of PCI_BRIDGE_CONTROL register on
emulated bridge.
With this change the function pci_reset_secondary_bus() starts working and
can reset connected PCIe card.
Link: https://lore.kernel.org/r/20211125124605.25915-13-pali@kernel.org
Fixes: 1f08673eef ("PCI: mvebu: Convert to PCI emulated bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df08ac0161 ]
This driver operates only in Root Complex mode, so ensure that hardware is
properly configured in Root Complex mode.
Link: https://lore.kernel.org/r/20211125124605.25915-10-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91a8d79fc7 ]
It looks like that mvebu PCIe controller has for each PCIe link fully
independent PCIe host bridge and so every PCIe Root Port is isolated not
only on its own bus but also isolated from each others. But in past device
tree structure was defined to put all PCIe Root Ports (as PCI Bridge
devices) into one root bus 0 and this bus is emulated by pci-mvebu.c
driver.
Probably reason for this decision was incorrect understanding of PCIe
topology of these Armada SoCs and also reason of misunderstanding how is
PCIe controller generating Type 0 and Type 1 config requests (it is fully
different compared to other drivers). Probably incorrect setup leaded to
very surprised things like having PCIe Root Port (PCI Bridge device, with
even incorrect Device Class set to Memory Controller) and the PCIe device
behind the Root Port on the same PCI bus, which obviously was needed to
somehow hack (as these two devices cannot be in reality on the same bus).
Properly set mvebu local bus number and mvebu local device number based on
PCI Bridge secondary bus number configuration. Also correctly report
configured secondary bus number in config space. And explain in driver
comment why this setup is correct.
Link: https://lore.kernel.org/r/20211125124605.25915-12-pali@kernel.org
Fixes: 1f08673eef ("PCI: mvebu: Convert to PCI emulated bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e42b855837 ]
According to PCI specifications bits [0:2] of Command Register, this should
be by default disabled on reset. So explicitly disable these bits at early
beginning of driver initialization.
Also remove code which unconditionally enables all 3 bits and let kernel
code (via pci_set_master() function) to handle bus mastering of PCI Bridge
via emulated PCI_COMMAND on emulated bridge.
Adjust existing functions mvebu_pcie_handle_iobase_change() and
mvebu_pcie_handle_membase_change() to handle PCI_IO_BASE and PCI_MEM_BASE
registers correctly even when bus mastering on emulated bridge is disabled.
Link: https://lore.kernel.org/r/20211125124605.25915-7-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2cf150216e ]
PCI IO type bits are already initialized in mvebu_pci_bridge_emul_init()
function and only when IO support is enabled. These type bits are read-only
and pci-bridge-emul.c code already does not allow to modify them from upper
layers.
When IO support is disabled then all IO registers should be read-only and
return zeros. Therefore do not modify PCI IO type bits in
mvebu_pci_bridge_emul_base_conf_write() callback.
Link: https://lore.kernel.org/r/20211125124605.25915-8-pali@kernel.org
Fixes: 1f08673eef ("PCI: mvebu: Convert to PCI emulated bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2070b2ddea ]
IORESOURCE_MEM_64 is not a resource type but a type flag.
Remove incorrect check for type IORESOURCE_MEM_64.
Link: https://lore.kernel.org/r/20211125160148.26029-2-kabel@kernel.org
Fixes: 64f160e19e ("PCI: aardvark: Configure PCIe resources from 'ranges' DT property")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e5ebc96ec ]
On imx6 and perhaps others when pcie probes you get a:
imx6q-pcie 33800000.pcie: invalid resource
This occurs because the atu is not specified in the DT and as such it
should not be remapped.
Link: https://lore.kernel.org/r/20211101180243.23761-1-tharvey@gateworks.com
Fixes: 281f1f99cf ("PCI: dwc: Detect number of iATU windows")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d2a14b5498 ]
Replace __clk_is_enabled() with pm_runtime_suspended(),
as __clk_is_enabled() was checking the wrong bus clock
and caused the following build error too:
arm-linux-gnueabi-ld: drivers/pci/controller/pcie-rcar-host.o: in function `rcar_pcie_aarch32_abort_handler':
pcie-rcar-host.c:(.text+0xdd0): undefined reference to `__clk_is_enabled'
Link: https://lore.kernel.org/r/20211115204641.12941-1-marek.vasut@gmail.com
Fixes: a115b1bd3a ("PCI: rcar: Add L1 link state fix into data abort hook")
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: linux-renesas-soc@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab344fd43f ]
When the DVFSRC (dynamic voltage and frequency scaling resource collector)
feature is not implemented, the PCIe hardware will assert a voltage request
signal when exit from the L1 PM Substates to request a specific Vcore
voltage, but cannot receive the voltage ready signal, which will cause
the link to fail to exit the L1 PM Substates.
Disable DVFSRC voltage request by default, we need to find a common way to
enable it in the future.
Link: https://lore.kernel.org/r/20211015063602.29058-1-jianjun.wang@mediatek.com
Fixes: d3bf75b579 ("PCI: mediatek-gen3: Add MediaTek Gen3 driver for MT8192")
Tested-by: Qizhong Cheng <qizhong.cheng@mediatek.com>
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Tzung-Bi Shih <tzungbi@google.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3149efcdf2 upstream.
When kernel boots with a NUMA topology with some NUMA nodes offline, the PCI
driver should only set an online NUMA node on the device. This can happen
during KDUMP where some NUMA nodes are not made online by the KDUMP kernel.
This patch also fixes the case where kernel is booting with "numa=off".
Fixes: 999dd956d8 ("PCI: hv: Add support for protocol 1.3 and support PCI_BUS_RELATIONS2")
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Tested-by: Purna Pavan Chandra Aekkaladevi <paekkaladevi@microsoft.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Link: https://lore.kernel.org/r/1643247814-15184-1-git-send-email-longli@linuxonhyperv.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23584c1ed3 upstream.
The Power Fault Detected bit in the Slot Status register differs from
all other hotplug events in that it is sticky: It can only be cleared
after turning off slot power. Per PCIe r5.0, sec. 6.7.1.8:
If a power controller detects a main power fault on the hot-plug slot,
it must automatically set its internal main power fault latch [...].
The main power fault latch is cleared when software turns off power to
the hot-plug slot.
The stickiness used to cause interrupt storms and infinite loops which
were fixed in 2009 by commits 5651c48cfa ("PCI pciehp: fix power fault
interrupt storm problem") and 99f0169c17 ("PCI: pciehp: enable
software notification on empty slots").
Unfortunately in 2020 the infinite loop issue was inadvertently
reintroduced by commit 8edf5332c3 ("PCI: pciehp: Fix MSI interrupt
race"): The hardirq handler pciehp_isr() clears the PFD bit until
pciehp's power_fault_detected flag is set. That happens in the IRQ
thread pciehp_ist(), which never learns of the event because the hardirq
handler is stuck in an infinite loop. Fix by setting the
power_fault_detected flag already in the hardirq handler.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=214989
Link: https://lore.kernel.org/linux-pci/DM8PR11MB5702255A6A92F735D90A4446868B9@DM8PR11MB5702.namprd11.prod.outlook.com
Fixes: 8edf5332c3 ("PCI: pciehp: Fix MSI interrupt race")
Link: https://lore.kernel.org/r/66eaeef31d4997ceea357ad93259f290ededecfd.1637187226.git.lukas@wunner.de
Reported-by: Joseph Bao <joseph.bao@intel.com>
Tested-by: Joseph Bao <joseph.bao@intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v4.19+
Cc: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3be9d243b2 upstream.
Since all PCI Express device Functions are required to implement the PCI
Express Capability structure, Capabilities List bit in PCI Status Register
must be hardwired to 1b. Capabilities Pointer register (which is already
set by pci-bride-emul.c driver) is valid only when Capabilities List is set
to 1b.
Link: https://lore.kernel.org/r/20211124155944.1290-7-pali@kernel.org
Fixes: 23a5fba4d9 ("PCI: Introduce PCI bridge emulated config space common logic")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f1050c5e1 upstream.
Older mvebu hardware provides PCIe Capability structure only in version 1.
New mvebu and aardvark hardware provides it in version 2. So do not force
version to 2 in pci_bridge_emul_init() and rather allow drivers to set
correct version. Drivers need to set version in pcie_conf.cap field without
overwriting PCI_CAP_LIST_ID register. Both drivers (mvebu and aardvark) do
not provide slot support yet, so do not set PCI_EXP_FLAGS_SLOT flag.
Link: https://lore.kernel.org/r/20211124155944.1290-6-pali@kernel.org
Fixes: 23a5fba4d9 ("PCI: Introduce PCI bridge emulated config space common logic")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12998087d9 upstream.
Some bits in PCI_EXP registers are reserved for non-root ports. Driver
pci-bridge-emul.c implements PCIe Root Port device therefore it should not
allow setting reserved bits of registers.
Properly define non-reserved bits for all PCI_EXP registers.
Link: https://lore.kernel.org/r/20211124155944.1290-5-pali@kernel.org
Fixes: 23a5fba4d9 ("PCI: Introduce PCI bridge emulated config space common logic")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b067ac63a upstream.
Some bits in PCI config space are reserved when device is PCIe. Properly
define behavior of PCI registers for PCIe emulated bridge and ensure that
it would not be possible change these reserved bits.
Link: https://lore.kernel.org/r/20211124155944.1290-3-pali@kernel.org
Fixes: 23a5fba4d9 ("PCI: Introduce PCI bridge emulated config space common logic")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c1a3b4d3e upstream.
If expansion ROM is unsupported (which is the case of pci-bridge-emul.c
driver) then ROM Base Address register must be implemented as read-only
register that return 0 when read, same as for unused Base Address
registers.
Link: https://lore.kernel.org/r/20211124155944.1290-2-pali@kernel.org
Fixes: 23a5fba4d9 ("PCI: Introduce PCI bridge emulated config space common logic")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 085a9f4343 upstream.
Use down_read_nested() and down_write_nested() when taking the
ctrl->reset_lock rw-sem, passing the number of PCIe hotplug controllers in
the path to the PCI root bus as lock subclass parameter.
This fixes the following false-positive lockdep report when unplugging a
Lenovo X1C8 from a Lenovo 2nd gen TB3 dock:
pcieport 0000:06:01.0: pciehp: Slot(1): Link Down
pcieport 0000:06:01.0: pciehp: Slot(1): Card not present
============================================
WARNING: possible recursive locking detected
5.16.0-rc2+ #621 Not tainted
--------------------------------------------
irq/124-pciehp/86 is trying to acquire lock:
ffff8e5ac4299ef8 (&ctrl->reset_lock){.+.+}-{3:3}, at: pciehp_check_presence+0x23/0x80
but task is already holding lock:
ffff8e5ac4298af8 (&ctrl->reset_lock){.+.+}-{3:3}, at: pciehp_ist+0xf3/0x180
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&ctrl->reset_lock);
lock(&ctrl->reset_lock);
*** DEADLOCK ***
May be due to missing lock nesting notation
3 locks held by irq/124-pciehp/86:
#0: ffff8e5ac4298af8 (&ctrl->reset_lock){.+.+}-{3:3}, at: pciehp_ist+0xf3/0x180
#1: ffffffffa3b024e8 (pci_rescan_remove_lock){+.+.}-{3:3}, at: pciehp_unconfigure_device+0x31/0x110
#2: ffff8e5ac1ee2248 (&dev->mutex){....}-{3:3}, at: device_release_driver+0x1c/0x40
stack backtrace:
CPU: 4 PID: 86 Comm: irq/124-pciehp Not tainted 5.16.0-rc2+ #621
Hardware name: LENOVO 20U90SIT19/20U90SIT19, BIOS N2WET30W (1.20 ) 08/26/2021
Call Trace:
<TASK>
dump_stack_lvl+0x59/0x73
__lock_acquire.cold+0xc5/0x2c6
lock_acquire+0xb5/0x2b0
down_read+0x3e/0x50
pciehp_check_presence+0x23/0x80
pciehp_runtime_resume+0x5c/0xa0
device_for_each_child+0x45/0x70
pcie_port_device_runtime_resume+0x20/0x30
pci_pm_runtime_resume+0xa7/0xc0
__rpm_callback+0x41/0x110
rpm_callback+0x59/0x70
rpm_resume+0x512/0x7b0
__pm_runtime_resume+0x4a/0x90
__device_release_driver+0x28/0x240
device_release_driver+0x26/0x40
pci_stop_bus_device+0x68/0x90
pci_stop_bus_device+0x2c/0x90
pci_stop_and_remove_bus_device+0xe/0x20
pciehp_unconfigure_device+0x6c/0x110
pciehp_disable_slot+0x5b/0xe0
pciehp_handle_presence_or_link_change+0xc3/0x2f0
pciehp_ist+0x179/0x180
This lockdep warning is triggered because with Thunderbolt, hotplug ports
are nested. When removing multiple devices in a daisy-chain, each hotplug
port's reset_lock may be acquired recursively. It's never the same lock, so
the lockdep splat is a false positive.
Because locks at the same hierarchy level are never acquired recursively, a
per-level lockdep class is sufficient to fix the lockdep warning.
The choice to use one lockdep subclass per pcie-hotplug controller in the
path to the root-bus was made to conserve class keys because their number
is limited and the complexity grows quadratically with number of keys
according to Documentation/locking/lockdep-design.rst.
Link: https://lore.kernel.org/linux-pci/20190402021933.GA2966@mit.edu/
Link: https://lore.kernel.org/linux-pci/de684a28-9038-8fc6-27ca-3f6f2f6400d7@redhat.com/
Link: https://lore.kernel.org/r/20211217141709.379663-1-hdegoede@redhat.com
Link: https://bugzilla.kernel.org/show_bug.cgi?id=208855
Reported-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c7a75d0782 upstream.
Commit 6dce5aa59e ("PCI: xgene: Use inbound resources for setup")
broke PCI support on XGene. The cause is the IB resources are now sorted
in address order instead of being in DT dma-ranges order. The result is
which inbound registers are used for each region are swapped. I don't
know the details about this h/w, but it appears that IB region 0
registers can't handle a size greater than 4GB. In any case, limiting
the size for region 0 is enough to get back to the original assignment
of dma-ranges to regions.
Link: https://lore.kernel.org/all/CA+enf=v9rY_xnZML01oEgKLmvY1NGBUUhnSJaETmXtDtXfaczA@mail.gmail.com/
Link: https://lore.kernel.org/r/20211129173637.303201-1-robh@kernel.org
Fixes: 6dce5aa59e ("PCI: xgene: Use inbound resources for setup")
Reported-by: Stéphane Graber <stgraber@ubuntu.com>
Tested-by: Stéphane Graber <stgraber@ubuntu.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Cc: stable@vger.kernel.org # v5.5+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 29bbc35e29 ]
pci_irq_vector() and pci_irq_get_affinity() use the list position to find the
MSI-X descriptor at a given index. That's correct for the normal case where
the entry number is the same as the list position.
But it's wrong for cases where MSI-X was allocated with an entries array
describing sparse entry numbers into the hardware message descriptor
table. That's inconsistent at best.
Make it always check the entry number because that's what the zero base
index really means. This change won't break existing users which use a
sparse entries array for allocation because these users retrieve the Linux
interrupt number from the entries array after allocation and none of them
uses pci_irq_vector() or pci_irq_get_affinity().
Fixes: aff171641d ("PCI: Provide sensible IRQ vector alloc/free routines")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20211206210223.929792157@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e445375882 upstream.
Like other SATA controller chips in the Marvell 88SE91xx series, the
Marvell 88SE9125 has the same DMA requester ID hardware bug that prevents
it from working under IOMMU. Add it to the list of devices that need the
quirk.
Without this patch, device initialization fails with DMA errors:
ata8: softreset failed (1st FIS failed)
DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Write NO_PASID] Request device [03:00.1] fault addr 0xfffc0000 [fault reason 0x02] Present bit in context entry is clear
DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Read NO_PASID] Request device [03:00.1] fault addr 0xfffc0000 [fault reason 0x02] Present bit in context entry is clear
After applying the patch, the controller can be successfully initialized:
ata8: SATA link up 1.5 Gbps (SStatus 113 SControl 330)
ata8.00: ATAPI: PIONEER BD-RW BDR-207M, 1.21, max UDMA/100
ata8.00: configured for UDMA/100
scsi 7:0:0:0: CD-ROM PIONEER BD-RW BDR-207M 1.21 PQ: 0 ANSI: 5
Link: https://lore.kernel.org/r/YahpKVR+McJVDdkD@work
Reported-by: Sam Bingner <sam@bingner.com>
Tested-by: Sam Bingner <sam@bingner.com>
Tested-by: Yifeng Li <tomli@tomli.me>
Signed-off-by: Yifeng Li <tomli@tomli.me>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 83dbf898a2 upstream.
Masking all unused MSI-X entries is done to ensure that a crash kernel
starts from a clean slate, which correponds to the reset state of the
device as defined in the PCI-E specificion 3.0 and later:
Vector Control for MSI-X Table Entries
--------------------------------------
"00: Mask bit: When this bit is set, the function is prohibited from
sending a message using this MSI-X Table entry.
...
This bit’s state after reset is 1 (entry is masked)."
A Marvell NVME device fails to deliver MSI interrupts after trying to
enable MSI-X interrupts due to that masking. It seems to take the MSI-X
mask bits into account even when MSI-X is disabled.
While not specification compliant, this can be cured by moving the masking
into the success path, so that the MSI-X table entries stay in device reset
state when the MSI-X setup fails.
[ tglx: Move it into the success path, add comment and amend changelog ]
Fixes: aa8092c1d1 ("PCI/MSI: Mask all unused MSI-X entries")
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-pci@vger.kernel.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211210161025.3287927-1-sr@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 94185adbfa upstream.
PCI_MSIX_FLAGS_MASKALL is set in the MSI-X control register at MSI-X
interrupt setup time. It's cleared on success, but the error handling path
only clears the PCI_MSIX_FLAGS_ENABLE bit.
That's incorrect as the reset state of the PCI_MSIX_FLAGS_MASKALL bit is
zero. That can be observed via lspci:
Capabilities: [b0] MSI-X: Enable- Count=67 Masked+
Clear the bit in the error path to restore the reset state.
Fixes: 438553958b ("PCI/MSI: Enable and mask MSI-X early")
Reported-by: Stefan Roese <sr@denx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Stefan Roese <sr@denx.de>
Cc: linux-pci@vger.kernel.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87tufevoqx.ffs@tglx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39bd54d43b upstream.
This reverts commit 239edf686c.
239edf686c ("PCI: aardvark: Fix support for PCI_ROM_ADDRESS1 on emulated
bridge") added support for the Type 1 Expansion ROM BAR at config offset
0x38, based on the register being listed in the Marvell Armada A3720 spec.
But the spec doesn't document it at all for RC mode, and there is no ROM in
the SOC, so remove this emulation for now.
The PCI bridge which represents aardvark's PCIe Root Port has an Expansion
ROM Base Address register at offset 0x30, but its meaning is different than
PCI's Expansion ROM BAR register, although the layout is the same. (This
is why we thought it does the same thing.)
First: there is no ROM (or part of BootROM) in the A3720 SOC dedicated for
PCIe Root Port (or controller in RC mode) containing executable code that
would initialize the Root Port, suitable for execution in bootloader (this
is how Expansion ROM BAR is used on x86).
Second: in A3720 spec the register (address 0xD0070030) is not documented
at all for Root Complex mode, but similar to other BAR registers, it has an
"entangled partner" in register 0xD0075920, which does address translation
for the BAR in 0xD0070030:
- the BAR register sets the address from the view of PCIe bus
- the translation register sets the address from the view of the CPU
The other BAR registers also have this entangled partner, and they can be
used to:
- in RC mode: address-checking on the receive side of the RC (they can
define address ranges for memory accesses from remote Endpoints to the
RC)
- in Endpoint mode: allow the remote CPU to access memory on A3720
The Expansion ROM BAR has only the Endpoint part documented, but from the
similarities we think that it can also be used in RC mode in that way.
So either Expansion ROM BAR has different meaning (if the hypothesis above
is true), or we don't know it's meaning (since it is not documented for RC
mode).
Remove the register from the emulated bridge accessing functions.
[bhelgaas: summarize reason for removal (first paragraph)]
Fixes: 239edf686c ("PCI: aardvark: Fix support for PCI_ROM_ADDRESS1 on emulated bridge")
Link: https://lore.kernel.org/r/20211125160148.26029-3-kabel@kernel.org
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f76b36d40b upstream.
Fix multiple link training issues in aardvark driver. The main reason of
these issues was misunderstanding of what certain registers do, since their
names and comments were misleading: before commit 96be36dbff ("PCI:
aardvark: Replace custom macros by standard linux/pci_regs.h macros"), the
pci-aardvark.c driver used custom macros for accessing standard PCIe Root
Bridge registers, and misleading comments did not help to understand what
the code was really doing.
After doing more tests and experiments I've come to the conclusion that the
SPEED_GEN register in aardvark sets the PCIe revision / generation
compliance and forces maximal link speed. Both GEN3 and GEN2 values set the
read-only PCI_EXP_FLAGS_VERS bits (PCIe capabilities version of Root
Bridge) to value 2, while GEN1 value sets PCI_EXP_FLAGS_VERS to 1, which
matches with PCI Express specifications revisions 3, 2 and 1 respectively.
Changing SPEED_GEN also sets the read-only bits PCI_EXP_LNKCAP_SLS and
PCI_EXP_LNKCAP2_SLS to corresponding speed.
(Note that PCI Express rev 1 specification does not define PCI_EXP_LNKCAP2
and PCI_EXP_LNKCTL2 registers and when SPEED_GEN is set to GEN1 (which
also sets PCI_EXP_FLAGS_VERS set to 1), lspci cannot access
PCI_EXP_LNKCAP2 and PCI_EXP_LNKCTL2 registers.)
Changing PCIe link speed can be done via PCI_EXP_LNKCTL2_TLS bits of
PCI_EXP_LNKCTL2 register. Armada 3700 Functional Specifications says that
the default value of PCI_EXP_LNKCTL2_TLS is based on SPEED_GEN value, but
tests showed that the default value is always 8.0 GT/s, independently of
speed set by SPEED_GEN. So after setting SPEED_GEN, we must also set value
in PCI_EXP_LNKCTL2 register via PCI_EXP_LNKCTL2_TLS bits.
Triggering PCI_EXP_LNKCTL_RL bit immediately after setting LINK_TRAINING_EN
bit actually doesn't do anything. Tests have shown that a delay is needed
after enabling LINK_TRAINING_EN bit. As triggering PCI_EXP_LNKCTL_RL
currently does nothing, remove it.
Commit 43fc679ced ("PCI: aardvark: Improve link training") introduced
code which sets SPEED_GEN register based on negotiated link speed from
PCI_EXP_LNKSTA_CLS bits of PCI_EXP_LNKSTA register. This code was added to
fix detection of Compex WLE900VX (Atheros QCA9880) WiFi GEN1 PCIe cards, as
otherwise these cards were "invisible" on PCIe bus (probably because they
crashed). But apparently more people reported the same issues with these
cards also with other PCIe controllers [1] and I was able to reproduce this
issue also with other "noname" WiFi cards based on Atheros QCA9890 chip
(with the same PCI vendor/device ids as Atheros QCA9880). So this is not an
issue in aardvark but rather an issue in Atheros QCA98xx chips. Also, this
issue only exists if the kernel is compiled with PCIe ASPM support, and a
generic workaround for this is to change PCIe Bridge to 2.5 GT/s link speed
via PCI_EXP_LNKCTL2_TLS_2_5GT bits in PCI_EXP_LNKCTL2 register [2], before
triggering PCI_EXP_LNKCTL_RL bit. This workaround also works when SPEED_GEN
is set to value GEN2 (5 GT/s). So remove this hack completely in the
aardvark driver and always set SPEED_GEN to value from 'max-link-speed' DT
property. Fix for Atheros QCA98xx chips is handled separately by patch [2].
These two things (code for triggering PCI_EXP_LNKCTL_RL bit and changing
SPEED_GEN value) also explain why commit 6964494582 ("PCI: aardvark:
Train link immediately after enabling training") somehow fixed detection of
those problematic Compex cards with Atheros chips: if triggering link
retraining (via PCI_EXP_LNKCTL_RL bit) was done immediately after enabling
link training (via LINK_TRAINING_EN), it did nothing. If there was a
specific delay, aardvark HW already initialized PCIe link and therefore
triggering link retraining caused the above issue. Compex cards triggered
link down event and disappeared from the PCIe bus.
Commit f4c7d053d7 ("PCI: aardvark: Wait for endpoint to be ready before
training link") added 100ms sleep before calling 'Start link training'
command and explained that it is a requirement of PCI Express
specification. But the code after this 100ms sleep was not doing 'Start
link training', rather it triggered PCI_EXP_LNKCTL_RL bit via PCIe Root
Bridge to put link into Recovery state.
The required delay after fundamental reset is already done in function
advk_pcie_wait_for_link() which also checks whether PCIe link is up.
So after removing the code which triggers PCI_EXP_LNKCTL_RL bit on PCIe
Root Bridge, there is no need to wait 100ms again. Remove the extra
msleep() call and update comment about the delay required by the PCI
Express specification.
According to Marvell Armada 3700 Functional Specifications, Link training
should be enabled via aardvark register LINK_TRAINING_EN after selecting
PCIe generation and x1 lane. There is no need to disable it prior resetting
card via PERST# signal. This disabling code was introduced in commit
5169a9851d ("PCI: aardvark: Issue PERST via GPIO") as a workaround for
some Atheros cards. It turns out that this also is Atheros specific issue
and affects any PCIe controller, not only aardvark. Moreover this Atheros
issue was triggered by juggling with PCI_EXP_LNKCTL_RL, LINK_TRAINING_EN
and SPEED_GEN bits interleaved with sleeps. Now, after removing triggering
PCI_EXP_LNKCTL_RL, there is no need to explicitly disable LINK_TRAINING_EN
bit. So remove this code too. The problematic Compex cards described in
previous git commits are correctly detected in advk_pcie_train_link()
function even after applying all these changes.
Note that with this patch, and also prior this patch, some NVMe disks which
support PCIe GEN3 with 8 GT/s speed are negotiated only at the lowest link
speed 2.5 GT/s, independently of SPEED_GEN value. After manually triggering
PCI_EXP_LNKCTL_RL bit (e.g. from userspace via setpci), these NVMe disks
change link speed to 5 GT/s when SPEED_GEN was configured to GEN2. This
issue first needs to be properly investigated. I will send a fix in the
future.
On the other hand, some other GEN2 PCIe cards with 5 GT/s speed are
autonomously by HW autonegotiated at full 5 GT/s speed without need of any
software interaction.
Armada 3700 Functional Specifications describes the following steps for
link training: set SPEED_GEN to GEN2, enable LINK_TRAINING_EN, poll until
link training is complete, trigger PCI_EXP_LNKCTL_RL, poll until signal
rate is 5 GT/s, poll until link training is complete, enable ASPM L0s.
The requirement for triggering PCI_EXP_LNKCTL_RL can be explained by the
need to achieve 5 GT/s speed (as changing link speed is done by throw to
recovery state entered by PCI_EXP_LNKCTL_RL) or maybe as a part of enabling
ASPM L0s (but in this case ASPM L0s should have been enabled prior
PCI_EXP_LNKCTL_RL).
It is unknown why the original pci-aardvark.c driver was triggering
PCI_EXP_LNKCTL_RL bit before waiting for the link to be up. This does not
align with neither PCIe base specifications nor with Armada 3700 Functional
Specification. (Note that in older versions of aardvark, this bit was
called incorrectly PCIE_CORE_LINK_TRAINING, so this may be the reason.)
It is also unknown why Armada 3700 Functional Specification says that it is
needed to trigger PCI_EXP_LNKCTL_RL for GEN2 mode, as according to PCIe
base specification 5 GT/s speed negotiation is supposed to be entirely
autonomous, even if initial speed is 2.5 GT/s.
[1] - https://lore.kernel.org/linux-pci/87h7l8axqp.fsf@toke.dk/
[2] - https://lore.kernel.org/linux-pci/20210326124326.21163-1-pali@kernel.org/
Link: https://lore.kernel.org/r/20211005180952.6812-12-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 454c53271f upstream.
PCIe config space can be initialized also before pci_bridge_emul_init()
call, so move rootcap initialization after PCI config space initialization.
This simplifies the function a little since it removes one if (ret < 0)
check.
Link: https://lore.kernel.org/r/20211005180952.6812-11-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 223dec14a0 upstream.
Commit 43f5c77bcb ("PCI: aardvark: Fix reporting CRS value") fixed
handling of CRS response and when CRSSVE flag was not enabled it marked CRS
response as failed transaction (due to simplicity).
But pci-aardvark.c driver is already waiting up to the PIO_RETRY_CNT count
for PIO config response and so we can with a small change implement
re-issuing of config requests as described in PCIe base specification.
This change implements re-issuing of config requests when response is CRS.
Set upper bound of wait cycles to around PIO_RETRY_CNT, afterwards the
transaction is marked as failed and an all-ones value is returned as
before.
We do this by returning appropriate error codes from function
advk_pcie_check_pio_status(). On CRS we return -EAGAIN and caller then
reissues transaction.
Link: https://lore.kernel.org/r/20211005180952.6812-10-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f21082fb20 upstream.
The ION AHCI device pretends that MSI masking isn't a thing, while it
actually implements it and needs MSIs to be unmasked to work. Add a quirk
to that effect.
Reported-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Rui Salvaterra <rsalvaterra@gmail.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Helgaas <helgaas@kernel.org>
Link: https://lore.kernel.org/r/CALjTZvbzYfBuLB+H=fj2J+9=DxjQ2Uqcy0if_PvmJ-nU-qEgkg@mail.gmail.com
Link: https://lore.kernel.org/r/20211104180130.3825416-3-maz@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2226667a14 upstream.
It appears that some devices are lying about their mask capability,
pretending that they don't have it, while they actually do.
The net result is that now that we don't enable MSIs on such
endpoint.
Add a new per-device flag to deal with this. Further patches will
make use of it, sadly.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20211104180130.3825416-2-maz@kernel.org
Cc: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4e17d65da upstream.
Change PCIe Max Payload Size setting in PCIe Device Control register to 512
bytes to align with PCIe Link Initialization sequence as defined in Marvell
Armada 3700 Functional Specification. According to the specification,
maximal Max Payload Size supported by this device is 512 bytes.
Without this kernel prints suspicious line:
pci 0000:01:00.0: Upstream bridge's Max Payload Size set to 256 (was 16384, max 512)
With this change it changes to:
pci 0000:01:00.0: Upstream bridge's Max Payload Size set to 256 (was 512, max 512)
Link: https://lore.kernel.org/r/20211005180952.6812-3-kabel@kernel.org
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3735459037 upstream.
free_msi_irqs() frees the MSI entries before destroying the sysfs entries
which are exposing them. Nothing prevents a concurrent free while a sysfs
file is read and accesses the possibly freed entry.
Move the sysfs release ahead of freeing the entries.
Fixes: 1c51b50c29 ("PCI/MSI: Export MSI mode using attributes, not kobjects")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Bjorn Helgaas <helgaas@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87sfw5305m.ffs@tglx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c8e9c9681 upstream.
The recent rework of PCI/MSI[X] masking moved the non-mask checks from the
low level accessors into the higher level mask/unmask functions.
This missed the fact that these accessors can be invoked from other places
as well. The missing checks break XEN-PV which sets pci_msi_ignore_mask and
also violates the virtual MSIX and the msi_attrib.maskbit protections.
Instead of sprinkling checks all over the place, lift them back into the
low level accessor functions. To avoid checking three different conditions
combine them into one property of msi_desc::msi_attrib.
[ josef: Fixed the missed conversion in the core code ]
Fixes: fcacdfbef5 ("PCI/MSI: Provide a new set of mask and unmask functions")
Reported-by: Josef Johansson <josef@oderland.se>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Josef Johansson <josef@oderland.se>
Cc: Bjorn Helgaas <helgaas@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5ec0a6fcb6 ]
Host crashes when pci_enable_atomic_ops_to_root() is called for VFs with
virtual buses. The virtual buses added to SR-IOV have bus->self set to NULL
and host crashes due to this.
PID: 4481 TASK: ffff89c6941b0000 CPU: 53 COMMAND: "bash"
...
#3 [ffff9a9481713808] oops_end at ffffffffb9025cd6
#4 [ffff9a9481713828] page_fault_oops at ffffffffb906e417
#5 [ffff9a9481713888] exc_page_fault at ffffffffb9a0ad14
#6 [ffff9a94817138b0] asm_exc_page_fault at ffffffffb9c00ace
[exception RIP: pcie_capability_read_dword+28]
RIP: ffffffffb952fd5c RSP: ffff9a9481713960 RFLAGS: 00010246
RAX: 0000000000000001 RBX: ffff89c6b1096000 RCX: 0000000000000000
RDX: ffff9a9481713990 RSI: 0000000000000024 RDI: 0000000000000000
RBP: 0000000000000080 R8: 0000000000000008 R9: ffff89c64341a2f8
R10: 0000000000000002 R11: 0000000000000000 R12: ffff89c648bab000
R13: 0000000000000000 R14: 0000000000000000 R15: ffff89c648bab0c8
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#7 [ffff9a9481713988] pci_enable_atomic_ops_to_root at ffffffffb95359a6
#8 [ffff9a94817139c0] bnxt_qplib_determine_atomics at ffffffffc08c1a33 [bnxt_re]
#9 [ffff9a94817139d0] bnxt_re_dev_init at ffffffffc08ba2d1 [bnxt_re]
Per PCIe r5.0, sec 9.3.5.10, the AtomicOp Requester Enable bit in Device
Control 2 is reserved for VFs. The PF value applies to all associated VFs.
Return -EINVAL if pci_enable_atomic_ops_to_root() is called for a VF.
Link: https://lore.kernel.org/r/1631354585-16597-1-git-send-email-selvin.xavier@broadcom.com
Fixes: 35f5ace5de ("RDMA/bnxt_re: Enable global atomic ops if platform supports")
Fixes: 430a23689d ("PCI: Add pci_enable_atomic_ops_to_root()")
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 496bb18483 ]
If an error occurs after a successful cdns_pcie_init_phy() call, it must be
undone by a cdns_pcie_disable_phy() call, as already done above and below.
Update the goto to branch at the correct place of the error handling path.
Link: https://lore.kernel.org/r/db477b0cb444891a17c4bb424467667dc30d0bab.1624794264.git.christophe.jaillet@wanadoo.fr
Fixes: 49e0efdce7 ("PCI: j721e: Add support to provide refclk to PCIe connector")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4caab28a62 ]
The condition register PCI_RCV_INTX is used in irq_mask() and irq_unmask()
callbacks. Accesses to register can occur at the same time without a lock.
Add a lock into each callback to prevent the issue.
And INTX mask and unmask fields in PCL_RCV_INTX register should only be
set/reset for each bit. Clearing by PCL_RCV_INTX_ALL_MASK should be
removed.
INTX status fields in PCL_RCV_INTX register only indicates each INTX
interrupt status, so the handler can't clear by writing 1 to the field.
The status is expected to be cleared by the interrupt origin.
The ack function has no meaning, so should remove it.
Suggested-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/1631924579-24567-1-git-send-email-hayashi.kunihiko@socionext.com
Fixes: 7e6d5cd88a ("PCI: uniphier: Add UniPhier PCIe host controller support")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Pali Rohár <pali@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d419052bc6 ]
Commit 43f5c77bcb ("PCI: aardvark: Fix reporting CRS value") started
using CRSSVE flag for handling CRS responses.
PCI_EXP_RTCTL_CRSSVE flag is stored only in emulated config space buffer
and there is handler for PCI_EXP_RTCTL register. So every read operation
from config space automatically clears CRSSVE flag as it is not defined in
PCI_EXP_RTCTL read handler.
Fix this by reading current CRSSVE bit flag from emulated space buffer and
appending it to PCI_EXP_RTCTL read response.
Link: https://lore.kernel.org/r/20211005180952.6812-5-kabel@kernel.org
Fixes: 43f5c77bcb ("PCI: aardvark: Fix reporting CRS value")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 464de7e7ff ]
Use dev_dbg() instead of dev_err() in advk_pcie_check_pio_status().
For example CRS is not an error status, it just says that the request
should be retried.
Link: https://lore.kernel.org/r/20211005180952.6812-4-kabel@kernel.org
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 84e1b4045d upstream.
Aardvark controller has something like config space of a Root Port
available at offset 0x0 of internal registers - these registers are used
for implementation of the emulated bridge.
The default value of Class Code of this bridge corresponds to a RAID Mass
storage controller, though. (This is probably intended for when the
controller is used as Endpoint.)
Change the Class Code to correspond to a PCI Bridge.
Add comment explaining this change.
Link: https://lore.kernel.org/r/20211028185659.20329-6-kabel@kernel.org
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc4fac42e5 upstream.
Aardvark supports PCIe Hot Reset via PCIE_CORE_CTRL1_REG.
Use it for implementing PCI_BRIDGE_CTL_BUS_RESET bit of PCI_BRIDGE_CONTROL
register on emulated bridge.
With this, the function pci_reset_secondary_bus() starts working and can
reset connected PCIe card. Custom userspace script [1] which uses setpci
can trigger PCIe Hot Reset and reset the card manually.
[1] https://alexforencich.com/wiki/en/pcie/hot-reset-linux
Link: https://lore.kernel.org/r/20211028185659.20329-7-kabel@kernel.org
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 771153fc88 upstream.
From very vague, ambiguous and incomplete information from Marvell we
deduced that the 32-bit Aardvark register at address 0x4
(PCIE_CORE_CMD_STATUS_REG), which is not documented for Root Complex mode
in the Functional Specification (only for Endpoint mode), controls two
16-bit PCIe registers: Command Register and Status Registers of PCIe Root
Port.
This means that bit 2 controls bus mastering and forwarding of memory and
I/O requests in the upstream direction. According to PCI specifications
bits [0:2] of Command Register, this should be by default disabled on
reset. So explicitly disable these bits at early setup of the Aardvark
driver.
Remove code which unconditionally enables all 3 bits and let kernel code
(via pci_set_master() function) to handle bus mastering of Root PCIe
Bridge via emulated PCI_COMMAND on emulated bridge.
Link: https://lore.kernel.org/r/20211028185659.20329-5-kabel@kernel.org
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # b2a56469d5 ("PCI: aardvark: Add FIXME comment for PCIE_CORE_CMD_STATUS_REG access")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95997723b6 upstream.
The PCIE_MSI_PAYLOAD_REG contains 16-bit MSI number, not only lower
8 bits. Fix reading content of this register and add a comment
describing the access to this register.
Link: https://lore.kernel.org/r/20211028185659.20329-4-kabel@kernel.org
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4313be159 upstream.
MSI domain callback .alloc() (implemented by advk_msi_irq_domain_alloc()
function) should return zero on success, since non-zero value indicates
failure.
When the driver was converted to generic MSI API in commit f21a8b1b68
("PCI: aardvark: Move to MSI handling using generic MSI support"), it
was converted so that it returns hwirq number.
Fix this.
Link: https://lore.kernel.org/r/20211028185659.20329-3-kabel@kernel.org
Fixes: f21a8b1b68 ("PCI: aardvark: Move to MSI handling using generic MSI support")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46ef6090db upstream.
Commit 366697018c ("PCI: aardvark: Add PHY support") introduced
configuration of PCIe Reference clock via PCIE_CORE_REF_CLK_REG register,
but did it incorrectly.
PCIe Reference clock differential pair is routed from system board to
endpoint card, so on CPU side it has output direction. Therefore it is
required to enable transmitting and disable receiving.
Default configuration according to Armada 3700 Functional Specifications is
enabled receiver part and disabled transmitter.
We need this change because otherwise PCIe Reference clock is configured to
some undefined state when differential pair is used for both transmitting
and receiving.
Fix this by disabling receiver part.
Link: https://lore.kernel.org/r/20211005180952.6812-6-kabel@kernel.org
Fixes: 366697018c ("PCI: aardvark: Add PHY support")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b650b7ff2 upstream.
Add support for reporting PCI_EXP_LNKSTA_DLLLA bit in Link Control register
on emulated bridge via current LTSSM state. Also correctly indicate DLLLA
capability via PCI_EXP_LNKCAP_DLLLARC bit in Link Control Capability
register.
Link: https://lore.kernel.org/r/20211005180952.6812-14-kabel@kernel.org
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1fb95d7d3c upstream.
There are lot of undocumented interrupt bits. To prevent unwanted
spurious interrupts, fix all *_ALL_MASK macros to define all interrupt
bits, so that driver can properly mask all interrupts, including those
which are undocumented.
Link: https://lore.kernel.org/r/20211005180952.6812-8-kabel@kernel.org
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 661c399a65 upstream.
Current implementation of advk_pcie_link_up() is wrong as it marks also
link disabled or hot reset states as link up.
Fix it by marking link up only to those states which are defined in PCIe
Base specification 3.0, Table 4-14: Link Status Mapped to the LTSSM.
To simplify implementation, Define macros for every LTSSM state which
aardvark hardware can return in CFG_REG register.
Fix also checking for link training according to the same Table 4-14.
Define a new function advk_pcie_link_training() for this purpose.
Link: https://lore.kernel.org/r/20211005180952.6812-13-kabel@kernel.org
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Cc: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a7ca6d7fa3 upstream.
The PCIE_ISR1_REG says which interrupts are currently set / active,
including those which are masked.
The driver currently reads this register and looks if some unmasked
interrupts are active, and if not, it clears status bits of _all_
interrupts, including the masked ones.
This is incorrect, since, for example, some drivers may poll these bits.
Remove this clearing, and also remove this early return statement
completely, since it does not change functionality in any way.
Link: https://lore.kernel.org/r/20211005180952.6812-7-kabel@kernel.org
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a41ae80bd upstream.
The pci_bridge_emul_conf_write() function correctly clears W1C bits in
cfgspace cache, but it does not inform the underlying implementation
about the clear request: the .write_op() method is given the value with
these bits cleared.
This is wrong if the .write_op() needs to know which bits were requested
to be cleared.
Fix the value to be passed into the .write_op() method to have requested
W1C bits set, so that it can clear them.
Both pci-bridge-emul users (mvebu and aardvark) are compatible with this
change.
Link: https://lore.kernel.org/r/20211028185659.20329-2-kabel@kernel.org
Fixes: 23a5fba4d9 ("PCI: Introduce PCI bridge emulated config space common logic")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e3f4bd3462 upstream.
When passing the Atheros QCA6174 through to a virtual machine, the VM hangs
at the point where the ath10k driver loads.
Add a quirk to avoid bus resets on this device, which avoids the hang.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/08982e05-b6e8-5a8d-24ab-da1488ee50a8@web.de
Signed-off-by: Ingmar Klein <ingmar_klein@web.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously, when msi_populate_sysfs() failed, we saved the error return
value as dev->msi_irq_groups, which leads to a page fault when
free_msi_irqs() calls msi_destroy_sysfs().
To prevent this, leave dev->msi_irq_groups alone when msi_populate_sysfs()
fails.
Found by the Hulk Robot when injecting a memory allocation fault in
msi_populate_sysfs():
BUG: unable to handle page fault for address: fffffffffffffff4
...
Call Trace:
msi_destroy_sysfs+0x30/0xa0
free_msi_irqs+0x11d/0x1b0
Fixes: 2f170814bd ("genirq/msi: Move MSI sysfs handling from PCI to MSI core")
Link: https://lore.kernel.org/r/20211012071556.939137-1-wanghai38@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Barry Song <song.bao.hua@hisilicon.com>
- Fix potential memory leak on a error path in eBPF.
- Fix handling of zpci device on reserve.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE3QHqV+H2a8xAv27vjYWKoQLXFBgFAmFg0FoACgkQjYWKoQLX
FBg3jgf8DLCs6JwK8GOz40CuZsajARwuagZy0udc3GbcZVNUog6GP7hJBU6q8pkm
JQMTl1C7Pe81p/aTOx2IIplV+owAVRnwdNBmj/psmZrI5P0CvLtTc4gVuCZJHJy4
9qt83KocgrN4G2K7qZDfiEAv+Ae/F7r20K5ZBX0exZBkOFeXZzUYVwWxM3pV45XB
Zx5AWmpHGGZFaS3EKW7E5VqswlGYIfUzGaXezN/cIl5HzMqqQMYo77eCJAWr//1z
s2s+vvEUBLGuHS8pDdXq8qR7Fq93cJSS7eo5zLVgtyZHr3Nn3+IlA0WKmPU3SmPE
+19I3L5hR0Ap6xh4ASgxciexnXFttQ==
=bGB2
-----END PGP SIGNATURE-----
Merge tag 's390-5.15-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Vasily Gorbik:
- Fix potential memory leak on a error path in eBPF
- Fix handling of zpci device on reserve
* tag 's390-5.15-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/pci: fix zpci_zdev_put() on reserve
bpf, s390: Fix potential memory leak about jit_data
Zeng Heng
Nirmal Patel
Kunihiko Hayashi
Vidya Sagar
Maciej W. Rozycki
Greg Kroah-Hartman
Pali Rohár
Pavan Chebbi
Robert Marko
Mohamed Khalfella
Christian Marangi
Stefan Roese
Shunsuke Mie
Serge Semin
Christoph Hellwig
Miaoqian Lin
Jeffrey Hugo
Lukas Wunner
Johan Hovold
Bjorn Helgaas
Daire McNamara
Kuppuswamy Sathyanarayanan
Francesco Dolcini
Jiantao Zhang
Dan Carpenter
Mario Limonciello
Yicong Yang
Rafael J. Wysocki
Marek Behún
Michael Kelley
Li Chen
Manivannan Sadhasivam
Hou Zhiqiang
Marc Zyngier
Mark Tomlinson
Liguang Zhang
Fabio Estevam
Ben Dooks
Alex Deucher
Tim Harvey
Marek Vasut
Jianjun Wang
Long Li
Hans de Goede
Rob Herring
Thomas Gleixner
Yifeng Li
Selvin Xavier
Christophe JAILLET
Ingmar Klein
Linus Torvalds
Wang Hai