The CONFIG_FSL_BOOKE mmu setup code fails when CONFIG_HIGHMEM=y
and the 3 fixed TLB entries cannot exactly map the lowmem size.
Each TLB entry can map 4MB, 16MB, 64MB or 256MB, so the failure
is observed when the kernel lowmem size is not equal to the
sum of up to 3 of those values.
Normally, memory is sized in nice numbers, but I observed this
problem while testing a crash dump kernel. The failure can
also be observed by artificially reducing the kernel's main
memory via the mem= kernel command line parameter.
This commit fixes the problem by setting __initial_memory_limit
in adjust_total_lowmem().
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add basic board support for the MPC8610 HPCD. This does
not include any support the SoC Display or Audio controllers.
Signed-off-by: Xianghua Xiao <x.xiao@freescale.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Jon Loelier <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Mode should be "cpu-qe" for QE in CPU mode. "qe" should be reserved
for native QE mode.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
According to booting-without-of.txt, compatible should be "fsl_spi" and
mode "cpu" or "qe" for the fsl SPI controllers.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch makes numerous miscellaneous code improvements to the QE library.
1. Remove struct ucc_common and merge ucc_init_guemr() into ucc_set_type()
(every caller of ucc_init_guemr() also calls ucc_set_type()). Modify all
callers of ucc_set_type() accordingly.
2. Remove the unused enum ucc_pram_initial_offset.
3. Refactor qe_setbrg(), also implement work-around for errata QE_General4.
4. Several printk() calls were missing the terminating \n.
5. Add __iomem where needed, and change u16 to __be16 and u32 to __be32 where
appropriate.
6. In ucc_slow_init() the RBASE and TBASE registers in the PRAM were programmed
with the wrong value.
7. Add the protocol type to struct us_info and updated ucc_slow_init() to
use it, instead of always programming QE_CR_PROTOCOL_UNSPECIFIED.
8. Rename ucc_slow_restart_x() to ucc_slow_restart_tx()
9. Add several macros in qe.h (mostly for slow UCC support, but also to
standardize some naming convention) and remove several unused macros.
10. Update ucc_geth.c to use the new macros.
11. Add ucc_slow_info.protocol to specify which QE_CR_PROTOCOL_xxx protcol
to use when initializing the UCC in ucc_slow_init().
12. Rename ucc_slow_pram.rfcr to rbmr and ucc_slow_pram.tfcr to tbmr, since
these are the real names of the registers.
13. Use the setbits, clrbits, and clrsetbits where appropriate.
14. Refactor ucc_set_qe_mux_rxtx().
15. Remove all instances of 'volatile'.
16. Simplify get_cmxucr_reg();
17. Replace qe_mux.cmxucrX with qe_mux.cmxucr[].
18. Updated struct ucc_geth because struct ucc_fast is not padded any more.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The PCI nodes on the MPC8568 dts didn't get moved up to be sibilings of the
SOC node when we did that clean up for some reason. Fix that up and some
minor whitespace and adjusting the size of the soc reg property.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MPC8568E-MDS have DS1374 chip on the I2C bus, thus let's use it.
This patch also adds #address-cells and #size-cells to the I2C
controllers nodes.
p.s. DS1374 rtc class driver is in the -mm tree, its name is
rtc-rtc-class-driver-for-the-ds1374.patch.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
i2c_board_info used semi-initialized, causing garbage in the
info->flags, and that, in turn, causes various symptoms of i2c
malfunctioning, like PEC mismatches.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The way the current CPM binding describes available multi-user (a.k.a.
dual-ported) RAM doesn't work well when there are multiple free regions,
and it doesn't work at all if the region doesn't begin at the start of
the muram area (as the hardware needs to be programmed with offsets into
this area). The latter situation can happen with SMC UARTs on CPM2, as its
parameter RAM is relocatable, u-boot puts it at zero, and the kernel doesn't
support moving it.
It is now described with a muram node, similar to QE. The current CPM
binding is sufficiently recent (i.e. never appeared in an official release)
that compatibility with existing device trees is not an issue.
The code supporting the new binding is shared between cpm1 and cpm2, rather
than remain separated. QE should be able to use this code as well, once
minor fixes are made to its device trees.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
According to the publicly available MPC8360E RM (rev. 1 from 09/2006 and rev. 2
from 05/2007) and MPC8323E RM (rev. 1 from 09/2006), CEURNR is the QE microcode
revision number register and is located at offset 0x1b8 within the QE internal
register space
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for the I2C devices handled by the rtc-ds1307 driver to
of_register_i2c_devices.
Cc: G. Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix a trivial printk typo in fsl_soc.
Cc: G. Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Previously, Soft_emulate_8xx was called with no implementation, resulting in
build failures whenever building 8xx without math emulation. The
implementation is copied from arch/ppc to resolve this issue.
However, this sort of minimal emulation is not a very good idea other than
for compatibility with existing userspaces, as it's less efficient than
soft-float and can mislead users into believing they have soft-float. Thus,
it is made a configurable option, off by default.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds cuboot support for MPC7448HPC2 platform.
The cuImage can be used with legacy u-boot without FDT support.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
1. PCI and reset are factored out into pq2.c. I renamed them from m82xx
to pq2 because they won't work on the Integrated Host Processor line of
82xx chips (i.e. 8240, 8245, and such).
2. The PCI PIC, which is nominally board-specific, is used on multiple
boards, and thus is used into pq2ads-pci-pic.c.
3. The new CPM binding is used.
4. General cleanup.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This board is also resold by Freescale under the names
"QUICCStart MPC885 Evaluation System" and "CWH-PPC-885XN-VE".
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It now uses the new CPM binding and the generic pin/clock functions, and
has assorted fixes and cleanup.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The localbus node is used to describe devices that are connected via a chip
select or similar mechanism. The advantages over placing the devices under
the root node are that it can be probed without probing other random things
under the root, and that the description of which chip select a given device
uses can be used to set up mappings if the firmware failed to do so in a
useful manner.
cuboot-pq2 is updated to match the binding; previously, it called itself
chipselect rather than localbus, and used phandle linkage between the
actual bus node and the control node (the current agreement is to simply use
the fully-qualified address of the control registers, and ignore the overlap
with the IMMR node).
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is just a rename patch; internal references to mpc82xx_ads will be
changed in the next one.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
m82xx_calibrate_decr(), mpc82xx_ads_show_cpuinfo(), and mpc82xx_halt() do
anything useful beyond what the generic code does.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The 8272 (and presumably other PCI PQ2 chips) appear to have the
same issue as the 83xx regarding PCI streaming DMA.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This provides a generic way for board code to set up CPM pins, rather
than directly poking magic values into registers.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Mostly sparse fixes (__iomem annotations, etc); also, cpm2_immr
is used rather than creating many temporary mappings.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The 8xx can only support a max of 8M during early boot (it seems a lot of
8xx boards only have 8M so the bug was never triggered), but the early
allocator isn't aware of this. The following change makes it able to run
with larger memory.
Signed-off-by: John Traill <john.traill@freescale.com>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The CPU15 erratum on MPC8xx chips can cause incorrect code execution
under certain circumstances, where there is a conditional or indirect
branch in the last word of a page, with a target in the last cache line
of the next page. This patch implements one of the suggested
workarounds, by forcing a TLB miss whenever execution crosses a page
boundary. This is done by invalidating the pages before and after the
one being loaded into the TLB in the ITLB miss handler.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
These let board code set up pins and clocks without having to
put magic numbers directly into the registers.
The clock function is mostly duplicated from the cpm2 version;
hopefully this stuff can be merged at some point.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
1. Keep a global mpc8xx_immr mapping, rather than constantly
creating temporary mappings.
2. Look for new fsl,cpm1 and fsl,cpm1-pic names.
3. Always reset the CPM when not using the udbg console;
this is required in case the firmware initialized a device
that is incompatible with one that the kernel is about to
use.
4. Remove some superfluous casts and header includes.
5. Change a usage of IMAP_ADDR to get_immrbase().
6. Use phys_addr_t, not uint, for dpram_pbase.
7. Various sparse-related fixes, such as __iomem annotations.
8. Remove mpc8xx_show_cpuinfo, which doesn't provide anything
useful beyond the generic cpuinfo handler.
9. Move prototypes for 8xx support functions from board files
to sysdev/commproc.h.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
1. Move CONSISTENT_START on 8xx so that it doesn't overlap the IMMR mapping.
2. The wrong register was being loaded into SPRN_MD_RPN.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This prevents some bootloader/bootwrapper characters from being lost.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Mostly a bunch of direct access to in/out conversions, plus a few
cast removals, __iomem annotations, and miscellaneous cleanup.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The existing OF glue code was crufty and broken. Rather than fix it,
it has been removed, and the serial driver now talks to the device tree
directly.
The non-CONFIG_PPC_CPM_NEW_BINDING code can go away once CPM platforms
are dropped from arch/ppc (which will hopefully be soon), and existing
arch/powerpc boards that I wasn't able to test on for this patchset get
converted (which should be even sooner).
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
fsl_get_immr() uses /soc/ranges to determine the immr.
mpc885_get_clock() transforms a crystal frequency into a system frequency
according to the PLL register settings.
pq2_get_clocks() does the same as the above for the PowerQUICC II,
except that it produces several different clocks.
The mpc8xx/pq2 set_clocks() functions modify common properties in
the device tree based on the given clock data.
The mpc885/pq2 fixup_clocks() functions call get_clocks(), and
pass the results to set_clocks().
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Consensus was reached to put PCI nodes at the root of the tree (and not
under /soc), but the phandle to a control node was rejected in favor of
simply not worrying about /pci/reg overlapping /soc/ranges.
This updates cuboot-82xx to not look for the phandle.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This code assumes that the ports have been previously set up, with
buffers in DPRAM.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This introduces a new device binding for the CPM and other devices on
these boards. Some of the changes include:
1. Proper namespace scoping for Freescale compatibles and properties.
2. Use compatible rather than things like device_type and model
to determine which particular variant of a device is present.
3. Give the drivers the relevant CPM command word directly, rather than
requiring it to have a lookup table based on device-id, SCC v. SMC, and
CPM version.
4. Specify the CPCR and the usable DPRAM region in the CPM's reg property.
Boards that do not require the legacy bindings should select
CONFIG_PPC_CPM_NEW_BINDING to enable the of_platform CPM devices. Once
all existing boards are converted and tested, the config option can
become default y to prevent new boards from using the old model. Once
arch/ppc is gone, the config option can be removed altogether.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
As suggested by David Gibson, now that we have a separate node
for the baud rate generators, it's better to use the standard
clock-frequency property than a cpm-node-level fsl,brg-frequency
property.
This patch updates existing places where fsl,brg-frequency is
used.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Commit 8112753bb2 made 44x in
ARCH=powerpc builds use cpu setup routines in cpu_setup_44x.S,
but didn't make a similar change for ARCH=ppc, and consequently
the ARCH=ppc builds fail with undefined symbols (since both use
the same cputable.c).
This fixes it by including cpu_setup_44x.S in the ARCH=ppc builds,
and by taking out the now-redundant FPU initialization in
arch/ppc/kernel/head_44x.S.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Reverts commit a15da8eff3
This driver is used by devices other than the xilinx opb-uartlite which
depend on bytewise access to the registers. The change to 32 bit access
does not work on these devices.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This simply adds the boilerplate default Ethernet address to embed_config
for the Xilinx platform (bug fix).
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Kumar Gala
Dale Farnsworth
Xianghua Xiao
Jason Jin
Peter Korsgaard
Timur Tabi
Anton Vorontsov
Scott Wood
Emil Medve
Roy Zang
John Traill
Paul Mackerras
Grant Likely