Link the ARM GIC to the INTC-AP module clock, and add it to the SYSC
"always-on" PM Domain, so it can be power managed using that clock.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This went unnoticed as the sata_rcar driver doesn't support Runtime PM
yet, but manages module clocks manually.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Exynos5433 LPASS module requires some clocks for proper operation with
power domain.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
When bypassing SWIOTLB on small-memory systems, we need to avoid calling
into swiotlb_dma_mapping_error() in exactly the same way as we avoid
swiotlb_dma_supported(), because the former also relies on SWIOTLB state
being initialised.
Under the assumptions for which we skip SWIOTLB, dma_map_{single,page}()
will only ever return the DMA-offset-adjusted physical address of the
page passed in, thus we can report success unconditionally.
Fixes: b67a8b29df ("arm64: mm: only initialize swiotlb when necessary")
CC: stable@vger.kernel.org
CC: Jisheng Zhang <jszhang@marvell.com>
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Fix warning:
"(COMPAT) selects COMPAT_BINFMT_ELF which has unmet direct dependencies
(COMPAT && BINFMT_ELF)"
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Memory regions marked as NOMAP should not be used for general allocation
by the kernel, and should not even be covered by the linear mapping
(hence the name). However, drivers or other subsystems (such as ACPI)
that access the firmware directly may legally access them, which means
it is also reasonable for such drivers to claim them by invoking
request_resource(). Currently, this is prevented by the fact that arm64's
request_standard_resources() marks reserved regions as IORESOURCE_BUSY.
So drop the IORESOURCE_BUSY flag from these requests.
Reported-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
If CONFIG_DEBUG_VIRTUAL=y and CONFIG_ARM64_SW_TTBR0_PAN=y:
virt_to_phys used for non-linear address: ffffff8008cc0000 (empty_zero_page+0x0/0x1000)
WARNING: CPU: 0 PID: 0 at arch/arm64/mm/physaddr.c:14 __virt_to_phys+0x28/0x60
...
[<ffffff800809abb4>] __virt_to_phys+0x28/0x60
[<ffffff8008a02600>] setup_arch+0x46c/0x4d4
Fixes: 2077be6783 ("arm64: Use __pa_symbol for kernel symbols")
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Will Deacon <will.deacon@arm.com>
All dts files for the sunxi platform have been switched to the generic
pinconf bindings. As a result, the sunxi specific pinctrl macros are
no longer used.
Remove the #include entry with the following command:
sed -i -e '/pinctrl\/sun4i-a10.h/D' \
arch/arm64/boot/dts/allwinner/*.dts?
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add initial dtsi file to support Hisilicon Hi3660 SoC with
support of Octal core CPUs in two clusters(4 * A53 & 4 * A73).
Also add dts file to support HiKey960 development board which
based on Hi3660 SoC.
The output console is earlycon "earlycon=pl011,0xfdf05000".
And the con_init uart5 with a fixed clock, which already
configured at bootloader.
When clock is available, the uart5 will be modified.
Tested on HiKey960 Board.
Signed-off-by: Chen Feng <puck.chen@hisilicon.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Add a file to debugfs to read the in-kernel state of the vgic. We don't
do any locking of the entire VGIC state while traversing all the IRQs,
so if the VM is running the user/developer may not see a quiesced state,
but should take care to pause the VM using facilities in user space for
that purpose.
We also don't support LPIs yet, but they can be added easily if needed.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Now that the corresponding device tree binding include has been merged,
convert the DTS files to use symbolic names instead of numeric ones.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Now that the corresponding device tree binding include has been merged,
convert the DTS files to use symbolic names instead of numeric ones.
Signed-off-by: Thierry Reding <treding@nvidia.com>
LDO7 regulator beside DSI and HDMI provides power for core blocks in Exynos
5433 SoC. Disabling it causes serious current leak - about 200mA.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Introduce a new architecture-specific get_arch_dma_ops() function
that takes a struct bus_type * argument. Add get_dma_ops() in
<linux/dma-mapping.h>.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Juergen Gross <jgross@suse.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-arch@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Russell King <linux@armlinux.org.uk>
Cc: x86@kernel.org
Signed-off-by: Doug Ledford <dledford@redhat.com>
Some but not all architectures provide set_dma_ops(). Move dma_ops
from struct dev_archdata into struct device such that it becomes
possible on all architectures to configure dma_ops per device.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Juergen Gross <jgross@suse.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-arch@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Russell King <linux@armlinux.org.uk>
Cc: x86@kernel.org
Signed-off-by: Doug Ledford <dledford@redhat.com>
Since the GXL family has S905X and S905D SoCs, we're keeping the SoC
name in the DTS filename for clarity. Rename this file accordingly to
be consistent with the rest of the GXL DTS files.
Cc: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Adds support for the WeTek Hub and Play2 boards.
The Hub is an extremely small IPTv Set-Top-Box and the Play2 is a more
traditionnal Satellite or Terrestrial and IPTv Set-Top-Box.
Both are based on the p200 Reference Design and out-of-tree support is
based on LibreELEC kernel at [1].
[1] https://github.com/wetek-enigma/linux-amlogic
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Ultra HD modes requires clock ticking at increased rate.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The arm64 DMA-mapping implementation sets the DMA ops to the IOMMU DMA
ops if we detect that an IOMMU is present for the master and the DMA
ranges are valid.
In the case when the IOMMU domain for the device is not of type
IOMMU_DOMAIN_DMA, then we have no business swizzling the ops, since
we're not in control of the underlying address space. This patch leaves
the DMA ops alone for masters attached to non-DMA IOMMU domains.
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Update the ARMv8 Crypto Extensions and the plain NEON AES implementations
in CBC and CTR modes to return the next IV back to the skcipher API client.
This is necessary for chaining to work correctly.
Note that for CTR, this is only done if the request is a round multiple of
the block size, since otherwise, chaining is impossible anyway.
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The LD11 SoC is equipped with SD-ctrl (0x59810000) as well as
MIO-ctrl (0x5b3e0000). The SD-ctrl block on this SoC has just
one register for controlling RST_n pin of the eMMC device.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
As per Exynos7 datasheet FSYS1 pinctrl block does not support drive
strength value of 0x3. This patch fixes this and update the correct
drive strength for sd0_xxx pin definitions.
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
ARM:
- Fix for timer setup on VHE machines
- Drop spurious warning when the timer races against the vcpu running
again
- Prevent a vgic deadlock when the initialization fails (for stable)
s390:
- Fix a kernel memory exposure (for stable)
x86:
- Fix exception injection when hypercall instruction cannot be patched
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJYglwIAAoJEED/6hsPKofoZp0H+gLLEeKP0Mu+olXiOWjB/KFp
WBDAR1872xIjvEcOl9l6AZgdmp2hk7KW1t+kJj5npgu237v6fHBO9ybqrAfhfU4l
PH23zOebL15HINcwCK6OcxOTiOtgae5Nui1cnLJBHDQgPTC/VmIE8NgV/qrMyo2r
Vth+K/cBLKiWG9JhyQvxmrfupNJUknLSH7CTnlO/fC8GEJzDfMpUl7B1Ui0TGK53
ExVgVLg3F28SErj9bUU8y4VJhMrwDAf2Kx2BNHqDbzXMzTdp0LrGRymFLl2/Gxez
zLtZDfGYYzEhPp1NuDydlxLb8ymnsQNB7K6Kau0w9JoAvOYwfUYfDt+GaTegwYM=
=dPtS
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Radim Krčmář:
"ARM:
- Fix for timer setup on VHE machines
- Drop spurious warning when the timer races against the vcpu running
again
- Prevent a vgic deadlock when the initialization fails (for stable)
s390:
- Fix a kernel memory exposure (for stable)
x86:
- Fix exception injection when hypercall instruction cannot be
patched"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: s390: do not expose random data via facility bitmap
KVM: x86: fix fixing of hypercalls
KVM: arm/arm64: vgic: Fix deadlock on error handling
KVM: arm64: Access CNTHCTL_EL2 bit fields correctly on VHE systems
KVM: arm/arm64: Fix occasional warning from the timer work function
uninitialised variables
- SWIOTLB DMA API fall-back allocation fix when the SWIOTLB buffer is
not initialised (all RAM is suitable for 32-bit DMA masks)
- Fix the bad_mode function returning for unhandled exceptions coming
from user space
- Fix name clash in __page_to_voff()
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=IArX
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- avoid potential stack information leak via the ptrace ABI caused by
uninitialised variables
- SWIOTLB DMA API fall-back allocation fix when the SWIOTLB buffer is
not initialised (all RAM is suitable for 32-bit DMA masks)
- fix the bad_mode function returning for unhandled exceptions coming
from user space
- fix name clash in __page_to_voff()
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: avoid returning from bad_mode
arm64/ptrace: Reject attempts to set incomplete hardware breakpoint fields
arm64/ptrace: Avoid uninitialised struct padding in fpr_set()
arm64/ptrace: Preserve previous registers for short regset write
arm64/ptrace: Preserve previous registers for short regset write
arm64/ptrace: Preserve previous registers for short regset write
arm64: mm: avoid name clash in __page_to_voff()
arm64: Fix swiotlb fallback allocation
Since much more arm64 SoCs with numa nodes, it's better to enable
NUMA and NUMA_BALANCING to improve the performance on test.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Common definition for I2S, PMC, SPDIF buses should not define any pull
control for the individual pins. Correct this by changing samsung,pin-pud
property to EXYNOS_PIN_PULL_NONE like it is defined for other Exynos SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
We've been sitting on fixes for a while, and they keep trickling in at a low
rate. Nothing in here comes across as particularly scary or noteworthy, for
the most part it's a large collection of small DT tweaks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cc1U
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"We've been sitting on fixes for a while, and they keep trickling in at
a low rate. Nothing in here comes across as particularly scary or
noteworthy, for the most part it's a large collection of small DT
tweaks"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (24 commits)
ARM: dts: da850-evm: fix read access to SPI flash
ARM: dts: omap3: Fix Card Detect and Write Protect on Logic PD SOM-LV
ARM64: dts: meson-gxbb-odroidc2: Disable SCPI DVFS
ARM: dts: OMAP5 / DRA7: indicate that SATA port 0 is available.
ARM: dts: NSP: Fix DT ranges error
ARM: multi_v7_defconfig: set bcm47xx watchdog
ARM: multi_v7_defconfig: fix config typo
ARM: dts: dra72-evm-revc: fix typo in ethernet-phy node
soc: ti: wkup_m3_ipc: Fix error return code in wkup_m3_ipc_probe()
ARM: ux500: fix prcmu_is_cpu_in_wfi() calculation
ARM: dts: sunxi: Change node name for pwrseq pin on Olinuxino-lime2-emmc
ARM: dts: sun8i: Support DTB build for NanoPi M1
ARM: dts: sun6i: hummingbird: Enable display engine again
ARM: dts: sun6i: Disable display pipeline by default
ARM, ARM64: dts: drop "arm,amba-bus" in favor of "simple-bus" part 3
ARM: dts: imx6qdl-nitrogen6_som2: fix sgtl5000 pinctrl init
ARM: dts: imx6qdl-nitrogen6_max: fix sgtl5000 pinctrl init
ARM: OMAP1: DMA: Correct the number of logical channels
ARM: dts: am335x-icev2: Remove the duplicated pinmux setting
ARM: OMAP2+: Fix WL1283 Bluetooth Baud Rate
...
Add a cut-down version of the DTS file for the community board
MACCHIATOBin from SolidRun based on Marvell Armada 8040 SoC to suit
the current mainlined Armada 8040 state.
This brings support for mainly SATA, SPI flash and UART. The USB
descriptions are included but are not tested in this form due to the
lack of mainline GPIO.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Acked-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
In order to keep consistency naming with the Nexbox A1 DTS file, remove the
S912 SoC name in the GXM DT files.
Suggested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The newly added DMA_ATTR_PRIVILEGED is useful for creating mappings that
are only accessible to privileged DMA engines. Implement it in
dma-iommu.c so that the ARM64 DMA IOMMU mapper can make use of it.
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Mitchel Humpherys <mitchelh@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Generally, taking an unexpected exception should be a fatal event, and
bad_mode is intended to cater for this. However, it should be possible
to contain unexpected synchronous exceptions from EL0 without bringing
the kernel down, by sending a SIGILL to the task.
We tried to apply this approach in commit 9955ac47f4 ("arm64:
don't kill the kernel on a bad esr from el0"), by sending a signal for
any bad_mode call resulting from an EL0 exception.
However, this also applies to other unexpected exceptions, such as
SError and FIQ. The entry paths for these exceptions branch to bad_mode
without configuring the link register, and have no kernel_exit. Thus, if
we take one of these exceptions from EL0, bad_mode will eventually
return to the original user link register value.
This patch fixes this by introducing a new bad_el0_sync handler to cater
for the recoverable case, and restoring bad_mode to its original state,
whereby it calls panic() and never returns. The recoverable case
branches to bad_el0_sync with a bl, and returns to userspace via the
usual ret_to_user mechanism.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Fixes: 9955ac47f4 ("arm64: don't kill the kernel on a bad esr from el0")
Reported-by: Mark Salter <msalter@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
4.11, please pull the following changes:
- Jon adds Device Tree nodes for the GICv2m and PAXB/PAXC PCIe interfaces on
the Northstar 2 SoCs, he also enables PAXC on the Northstar 2 SVK reference
board. He also updates the reserved memory entry for the Nitro firmware,
required to get the on-chip NICs to work. Finally he adds support for the
BCM958712DxXMC reference board which is a subset of existing boards.
-----BEGIN PGP SIGNATURE-----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=JBHv
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.11/devicetree-arm64' of http://github.com/Broadcom/stblinux into next/dt64
This pull request contains Broadcom ARM64-based SoC Device Tree changes for
4.11, please pull the following changes:
- Jon adds Device Tree nodes for the GICv2m and PAXB/PAXC PCIe interfaces on
the Northstar 2 SoCs, he also enables PAXC on the Northstar 2 SVK reference
board. He also updates the reserved memory entry for the Nitro firmware,
required to get the on-chip NICs to work. Finally he adds support for the
BCM958712DxXMC reference board which is a subset of existing boards.
* tag 'arm-soc/for-4.11/devicetree-arm64' of http://github.com/Broadcom/stblinux:
arm64: dts: NS2: add support for XMC form factor
arm64: dts: NS2: reserve memory for Nitro firmware
arm64: dts: NS2: enable PAXC on NS2 SVK
arm64: dts: NS2: enable GICv2m for PAXB/PAXC interfaces
Signed-off-by: Olof Johansson <olof@lixom.net>
1. Addition of Coresight support on Juno R1 and R2 variants
2. Addition of STM(System Trace Macrocell) support on all Juno variants
3. Removed incorrect nesting of dtsi files
4. Removed untested USB hub only available on initial Juno R0 motherboard
5. Added ETR SMMU power domain and dma-ranges property
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VeiR
-----END PGP SIGNATURE-----
Merge tag 'juno-updates-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/dt64
ARMv8 Vexpress/Juno DT updates for v4.11
1. Addition of Coresight support on Juno R1 and R2 variants
2. Addition of STM(System Trace Macrocell) support on all Juno variants
3. Removed incorrect nesting of dtsi files
4. Removed untested USB hub only available on initial Juno R0 motherboard
5. Added ETR SMMU power domain and dma-ranges property
* tag 'juno-updates-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: juno: remove motherboard USB node
arm64: dts: juno: add ETR SMMU power domain
arm64: dts: juno: add dma-ranges property
arm64: dts: juno: add missing CoreSight STM component
arm64: dts: juno: add CoreSight support for Juno r1/r2 variants
arm64: dts: juno: refactor CoreSight support on Juno r0
arm64: dts: juno: remove dtsi nesting inside tree structure
Signed-off-by: Olof Johansson <olof@lixom.net>
Add pinctrl nodes for HDMI HPD and DDC pins modes for Amlogic Meson GXL
and GXBB SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
There is one blue LED on the front of the device. Keep it lit and
configure it as panic indicator.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This adds pinctrl group nodes for the CTS and RTS pins of each serial
controller. This makes it possible to enable the CTS and RTS pins which
are controlled by the serial controller hardware (through the meson_uart
driver).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This adds the missing node for the uart_AO_B port to the meson-gx.dtsi
(as this is supported by GXBB, GXL and GXM) along with the required
pinctrl pins. This is required as some boards are using it (the boards
from the Khadas VIM series for example have it exposed on the pin
headers).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
We cannot preserve partial fields for hardware breakpoints, because
the values written by userspace to the hardware breakpoint
registers can't subsequently be recovered intact from the hardware.
So, just reject attempts to write incomplete fields with -EINVAL.
Cc: <stable@vger.kernel.org> # 3.7.x-
Fixes: 478fcb2cdb ("arm64: Debugging support")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Will Deacon <Will.Deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds an explicit __reserved[] field to user_fpsimd_state
to replace what was previously unnamed padding.
This ensures that data in this region are propagated across
assignment rather than being left possibly uninitialised at the
destination.
Cc: <stable@vger.kernel.org> # 3.7.x-
Fixes: 60ffc30d56 ("arm64: Exception handling")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Will Deacon <Will.Deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Ensure that if userspace supplies insufficient data to
PTRACE_SETREGSET to fill all the registers, the thread's old
registers are preserved.
Cc: <stable@vger.kernel.org> # 4.3.x-
Fixes: 5d220ff942 ("arm64: Better native ptrace support for compat tasks")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Will Deacon <Will.Deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Ensure that if userspace supplies insufficient data to
PTRACE_SETREGSET to fill all the registers, the thread's old
registers are preserved.
Cc: <stable@vger.kernel.org> # 3.19.x-
Fixes: 766a85d7bc ("arm64: ptrace: add NT_ARM_SYSTEM_CALL regset")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Will Deacon <Will.Deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Ensure that if userspace supplies insufficient data to
PTRACE_SETREGSET to fill all the registers, the thread's old
registers are preserved.
Cc: <stable@vger.kernel.org> # 3.7.x-
Fixes: 478fcb2cdb ("arm64: Debugging support")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Will Deacon <Will.Deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The "samsung,exynos5433-mipi-video-phy" and "samsung,exynos5250-dwusb3"
DT bindings don't specify a reg property for these nodes, so having a
unit name leads to the following DTC warnings:
Node /soc/video-phy@105c0710 has a unit name, but no reg property
Node /soc/usb@15400000 has a unit name, but no reg property
Node /soc/usb@15a00000 has a unit name, but no reg property
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The first batch of Juno boards included a discrete USB controller chip
as a contingency in case of issues with the USB 2.0 IP integrated into
the SoC. As it turned out, the latter was fine, and to the best of my
knowledge the motherboard USB was never even brought up and validated.
Since this also isn't present on later boards, and uses a compatible
string undocumented and unmatched by any driver in the kernel, let's
just tidy it away for ever to avoid any confusion.
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
It is not at all clear from the documentation, but straightforward to
determine in practice, that the ETR SMMU is actually in the DEBUGSYS
power domain. Add that to the DT so that anyone brave enough to enable
said SMMU doesn't experience a system lockup on boot, especially a
sneaky one which goes away as soon as you connect an external debugger
to have a look at where it's stuck (thus powering up DEBUGSYS by other
means and allowing it to make progress again before actually halting...)
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The interconnects around Juno have a 40-bit address width, and DMA
masters have no restrictions beyond their own individual limitations.
Describe this to ensure that DT-based DMA masks get set up correctly
for all devices capable of 40-bit addressing.
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The arm64 __page_to_voff() macro takes a parameter called 'page', and
also refers to 'struct page'. Thus, if the value passed in is not
called 'page', we'll refer to the wrong struct name (which might not
exist).
Fixes: 3fa72fe9c6 ("arm64: mm: fix __page_to_voff definition")
Acked-by: Mark Rutland <mark.rutland@arm.com>
Suggested-by: Volodymyr Babchuk <Volodymyr_Babchuk@epam.com>
Signed-off-by: Oleksandr Andrushchenko <Oleksandr_Andrushchenko@epam.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds the missing CoreSight STM component definition to the
device tree of all the juno variants(r0,r1,r2)
STM component is connected to different funnels depending on Juno
platform variant.
Reviewed-and-tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mike Leach <mike.leach@linaro.org>
[sudeep.holla@arm.com: minor changelog update and reorganising the STM
node back into juno-base.dtsi to avoid duplication]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The CoreSight support added for Juno is valid for only Juno r0.
The Juno r1 and r2 variants have additional components and alternative
connection routes between trace source and sinks.
This patch builds on top of the existing r0 support and extends it to
Juno r1/r2 variants.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mike Leach <mike.leach@linaro.org>
[sudeep.holla@arm.com: minor changelog update and major reorganisation of
the common coresight components back into juno-base.dtsi to avoid
duplication, also renamed funnel node names]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Currently the Coresight components are supported only on Juno r0
variant. In preparation to add support to Juno r1/r2 variants, this
patch refactors the existing coresight device nodes so that r1/r2
support can be added easily.
It also cleans up some of the device node names which were previously
named so as they were confused as the labels rather than the node names.
Reviewed-and-tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Currently juno-clock.dtsi and juno-base.dtsi are nested badly inside
the device tree structure. It's generally good practice to ensure that
individual dtsi stand by themselves at the top of the file.
This patch removes the nesting of the above mentioned dtsi files and
makes them independent.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The current hardware is not able to run with all cores enabled at a
cluster frequency superior at 1536MHz.
But the currently shipped u-boot for the platform still reports an OPP
table with possible DVFS frequency up to 2GHz, and will not change since
the off-tree linux tree supports limiting the OPPs with a kernel parameter.
A recent u-boot change reports the boot-time DVFS around 100MHz and
the default performance cpufreq governor sets the maximum frequency.
Previous version of u-boot reported to be already at the max OPP and
left the OPP as is.
Nevertheless, other governors like ondemand could setup the max frequency
and make the system crash.
This patch disables the DVFS clock and disables cpufreq.
Fixes: 70db166a2b ("ARM64: dts: meson-gxbb: Add SCPI with cpufreq & sensors Nodes")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Some places in the kernel open-code sequences using ADRP for a symbol
another instruction using a :lo12: relocation for that same symbol.
These sequences are easy to get wrong, and more painful to read than is
necessary. For these reasons, it is preferable to use the
{adr,ldr,str}_l macros for these cases.
This patch makes use of these in entry-ftrace.S, removing open-coded
sequences using adrp. This results in a minor code change, since a
temporary register is not used when generating the address for some
symbols, but this is fine, as the value of the temporary register is not
used elsewhere.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Some places in the kernel open-code sequences using ADRP for a symbol
another instruction using a :lo12: relocation for that same symbol.
These sequences are easy to get wrong, and more painful to read than is
necessary. For these reasons, it is preferable to use the
{adr,ldr,str}_l macros for these cases.
This patch makes use of these in efi-entry.S, removing open-coded
sequences using adrp.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Some places in the kernel open-code sequences using ADRP for a symbol
another instruction using a :lo12: relocation for that same symbol.
These sequences are easy to get wrong, and more painful to read than is
necessary. For these reasons, it is preferable to use the
{adr,ldr,str}_l macros for these cases.
This patch makes use of adr_l these in head.S, removing an open-coded
sequence using adrp.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
- Fix for timer setup on VHE machines
- Drop spurious warning when the timer races against
the vcpu running again
- Prevent a vgic deadlock when the initialization fails
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7cIH
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-4.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm
KVM/ARM updates for 4.10-rc4
- Fix for timer setup on VHE machines
- Drop spurious warning when the timer races against
the vcpu running again
- Prevent a vgic deadlock when the initialization fails
The cache hierarchy can be identified through Cache Level ID(CLIDR)
architected system register. However in some cases it will provide
only the number of cache levels that are integrated into the processor
itself. In other words, it can't provide any information about the
caches that are external and/or transparent.
Some platforms require to export the information about all such external
caches to the userspace applications via the sysfs interface.
This patch adds support to override the cache levels using device tree
to take such external non-architected caches into account.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Tested-by: Tan Xiaojun <tanxiaojun@huawei.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit b67a8b29df introduced logic to skip swiotlb allocation when all memory
is DMA accessible anyway.
While this is a great idea, __dma_alloc still calls swiotlb code unconditionally
to allocate memory when there is no CMA memory available. The swiotlb code is
called to ensure that we at least try get_free_pages().
Without initialization, swiotlb allocation code tries to access io_tlb_list
which is NULL. That results in a stack trace like this:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
[...]
[<ffff00000845b908>] swiotlb_tbl_map_single+0xd0/0x2b0
[<ffff00000845be94>] swiotlb_alloc_coherent+0x10c/0x198
[<ffff000008099dc0>] __dma_alloc+0x68/0x1a8
[<ffff000000a1b410>] drm_gem_cma_create+0x98/0x108 [drm]
[<ffff000000abcaac>] drm_fbdev_cma_create_with_funcs+0xbc/0x368 [drm_kms_helper]
[<ffff000000abcd84>] drm_fbdev_cma_create+0x2c/0x40 [drm_kms_helper]
[<ffff000000abc040>] drm_fb_helper_initial_config+0x238/0x410 [drm_kms_helper]
[<ffff000000abce88>] drm_fbdev_cma_init_with_funcs+0x98/0x160 [drm_kms_helper]
[<ffff000000abcf90>] drm_fbdev_cma_init+0x40/0x58 [drm_kms_helper]
[<ffff000000b47980>] vc4_kms_load+0x90/0xf0 [vc4]
[<ffff000000b46a94>] vc4_drm_bind+0xec/0x168 [vc4]
[...]
Thankfully swiotlb code just learned how to not do allocations with the FORCE_NO
option. This patch configures the swiotlb code to use that if we decide not to
initialize the swiotlb framework.
Fixes: b67a8b29df ("arm64: mm: only initialize swiotlb when necessary")
Signed-off-by: Alexander Graf <agraf@suse.de>
CC: Jisheng Zhang <jszhang@marvell.com>
CC: Geert Uytterhoeven <geert+renesas@glider.be>
CC: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
- Correct license text which was mangled when switching to dual license
- Add SPI and I2C nodes on Armada 3700(driver support had been already
merged)
- Add support for the ethernet switch on the EspressoBin board (driver
support not yet merged)
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWHkJzyMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71S01AKCYMJtp3ZYd
nWFez/9S2sUDbmEQRwCgiwEJ4cDIz68s5+EXJE4nXAKlhrg=
=HIbH
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.11-1' of git://git.infradead.org/linux-mvebu into next/dt64
mvebu dt64 for 4.11 (part 1)
- Correct license text which was mangled when switching to dual license
- Add SPI and I2C nodes on Armada 3700(driver support had been already
merged)
- Add support for the ethernet switch on the EspressoBin board (driver
support not yet merged)
* tag 'mvebu-dt64-4.11-1' of git://git.infradead.org/linux-mvebu:
ARM64: dts: marvell: Correct license text
arm64: dts: marvell: Add I2C definitions for the Armada 3700
arm64: dts: marvell: Enable spi0 on the board Armada-3720-db
arm64: dts: marvell: Add definition of SPI controller for Armada 3700
arm64: dts: marvell: Add ethernet switch definition for the ESPRESSObin
Signed-off-by: Olof Johansson <olof@lixom.net>
Update arm64 defconfig by adding XORv2 for Marvell Armada 7K/8K
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWHkE/iMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71XkoAJ9NBtmwvDxp
Rqi2aEq7ki6oU/jybwCdG0CYDLRyzoR4HKVy0mVtgnsMnLw=
=lET3
-----END PGP SIGNATURE-----
Merge tag 'mvebu-defconfig64-4.11-1' of git://git.infradead.org/linux-mvebu into next/arm64
mvebu defconfig64 for 4.11 (part 1)
Update arm64 defconfig by adding XORv2 for Marvell Armada 7K/8K
* tag 'mvebu-defconfig64-4.11-1' of git://git.infradead.org/linux-mvebu:
arm64: defconfig: enable XORv2 for Marvell Armada 7K/8K
Signed-off-by: Olof Johansson <olof@lixom.net>
1. Add bus frequency and voltage scalling on Exynos5433 TM2 device (along with
necessary bus nodes and Platform Performance Monitoring Unit on Exynos5433).
2. Use macros for pinctrl settings on Exynos5433.
This contains necessary header with bindings.
3. Minor cleanups in Exynos5433 DTSI and boards using it.
4. Create common DTSI betweem Exynos5433 TM2E and TM2E.
5. Add HDMI/TV to Exynos5433 TM2.
-----BEGIN PGP SIGNATURE-----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=reZn
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt64-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt64
Samsung DeviceTree ARM64 update for v4.11:
1. Add bus frequency and voltage scalling on Exynos5433 TM2 device (along with
necessary bus nodes and Platform Performance Monitoring Unit on Exynos5433).
2. Use macros for pinctrl settings on Exynos5433.
This contains necessary header with bindings.
3. Minor cleanups in Exynos5433 DTSI and boards using it.
4. Create common DTSI betweem Exynos5433 TM2E and TM2E.
5. Add HDMI/TV to Exynos5433 TM2.
* tag 'samsung-dt64-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: Enable HDMI/TV path on Exynos5433-TM2
arm64: dts: exynos: Add HDMI node to Exynos5433
arm64: dts: exynos: Add DECON_TV node to Exynos5433
arm64: dts: exynos: Fix addresses in node names on Exynos5433
arm64: dts: exynos: Make TM2 and TM2E independent from each other
arm64: dts: exynos: Fix wrong values for ldo23 and ldo25 on TM2/TM2E
arm64: dts: exynos: Remove unsupported regulator-always-off property from TM2E
arm64: dts: exynos: Comply to the samsung pinctrl naming convention in TM2
arm64: dts: exynos: Use macros for pinctrl configuration on Exynos5433
pinctrl: dt-bindings: samsung: add drive strength macros for Exynos5433
arm64: dts: exynos: Add support of bus frequency using VDD_INT on Exynos5433 TM2
arm64: dts: exynos: Add bus nodes using VDD_INT for Exynos5433
arm64: dts: exynos: Add PPMU node to Exynos5433
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds support to volume-up key found on the board.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
96Boards specs require all GPIO signals to be at 1.8V.
Limit MPP4, which is PIN28 on J8, to 1.8V(L5).
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
VOL/ZOOM+ button on DB410c is connected to
SoC GPIO 104. Add support for it.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support to hdmi audio via adv7533.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Fix typo in node name to reflect the correct pin name.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the wcnss remoteproc node the SMD edge and the wcnss ctrl, bluetooth
and wifi nodes specified and enable this on db410c.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The rpmcc driver is providing the XO clock, which is the parent of almost
all clocks. But during boot, this driver may probe later and leave most of
the clocks without parent. The common clock framework currently reports
invalid rate for orphan clocks and this may confuse drivers.
To resolve this, use fixed clocks registration until we have some support
to deal with the this issue. Removing the generic rpmcc compatible is
enough to switch back to fixed factor XO clock.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The structure rockchip_clk_provider needs to refer the GRF regmap
in somewhere, if the CRU node has not "rockchip,grf" property,
calling syscon_regmap_lookup_by_phandle will return an invalid GRF
regmap, and the MUXGRF type clock will be not supported.
Therefore, we need to add them.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
According to [0], the contribution field for each cooling-device express
their relative power efficiency. Higher weights express higher power
efficiency. Weighting is relative such that if each cooling device has a
weight of 1 they are considered equal. This is particularly useful in
heterogeneous systems where two cooling devices may perform the same kind
of compute, but with different efficiency.
[0] Documentation/thermal/power_allocator.txt
According to Mediatek IC designer, the power efficiency ratio between the
LITTLE core cluster (cooling-device cpu0) and big core cluster
(cooling-device cpu1) is around 3:1 (3072:1024).
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
To support HDMI 4K resolution, mmsys need clcok
mm_sel to be 400MHz.
The board .dts file should override the clock rate
property with the higher VENCPLL frequency the board
supports HDMI 4K resolution.
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Definition of cpu ranges are hard to read if the cpu variant is not
zero. Provide MIDR_CPU_VAR_REV() macro to describe the full hardware
revision of a cpu including variant and (minor) revision.
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cosmetic change to use phys_addr_t instead of unsigned long for the
return value of __pa_symbol().
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Miles Chen <miles.chen@mediatek.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Current KVM world switch code is unintentionally setting wrong bits to
CNTHCTL_EL2 when E2H == 1, which may allow guest OS to access physical
timer. Bit positions of CNTHCTL_EL2 are changing depending on
HCR_EL2.E2H bit. EL1PCEN and EL1PCTEN are 1st and 0th bits when E2H is
not set, but they are 11th and 10th bits respectively when E2H is set.
In fact, on VHE we only need to set those bits once, not for every world
switch. This is because the host kernel runs in EL2 with HCR_EL2.TGE ==
1, which makes those bits have no effect for the host kernel execution.
So we just set those bits once for guests, and that's it.
Signed-off-by: Jintack Lim <jintack@cs.columbia.edu>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Per the discussion of bug fix[1], we now actually
leaves the default clock choice for pcie phy is
derived from 24MHz OSC to guarantee the least BER.
So let's add aspm-no-l0s here and folks could delete
this property from their dts.
[1] https://patchwork.kernel.org/patch/9470519/
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
When CONFIG_RANDOMIZE_MODULE_REGION_FULL=y, the offset between loaded
modules and the core kernel may exceed 4 GB, putting symbols exported
by the core kernel out of the reach of the ordinary adrp/add instruction
pairs used to generate relative symbol references. So make the adr_l
macro emit a movz/movk sequence instead when executing in module context.
While at it, remove the pointless special case for the stack pointer.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
ARM v8.1 extensions include support for rounding double multiply
add/subtract instructions to the A64 SIMD instructions set. Let
the userspace know about it via a HWCAP bit.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This is a reimplementation of the NEON version of the bit-sliced AES
algorithm. This code is heavily based on Andy Polyakov's OpenSSL version
for ARM, which is also available in the kernel. This is an alternative for
the existing NEON implementation for arm64 authored by me, which suffers
from poor performance due to its reliance on the pathologically slow four
register variant of the tbl/tbx NEON instruction.
This version is about ~30% (*) faster than the generic C code, but only in
cases where the input can be 8x interleaved (this is a fundamental property
of bit slicing). For this reason, only the chaining modes ECB, XTS and CTR
are implemented. (The significance of ECB is that it could potentially be
used by other chaining modes)
* Measured on Cortex-A57. Note that this is still an order of magnitude
slower than the implementations that use the dedicated AES instructions
introduced in ARMv8, but those are part of an optional extension, and so
it is good to have a fallback.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This adds a scalar implementation of AES, based on the precomputed tables
that are exposed by the generic AES code. Since rotates are cheap on arm64,
this implementation only uses the 4 core tables (of 1 KB each), and avoids
the prerotated ones, reducing the D-cache footprint by 75%.
On Cortex-A57, this code manages 13.0 cycles per byte, which is ~34% faster
than the generic C code. (Note that this is still >13x slower than the code
that uses the optional ARMv8 Crypto Extensions, which manages <1 cycles per
byte.)
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In addition to wrapping the AES-CTR cipher into the async SIMD wrapper,
which exposes it as an async skcipher that defers processing to process
context, expose our AES-CTR implementation directly as a synchronous cipher
as well, but with a lower priority.
This makes the AES-CTR transform usable in places where synchronous
transforms are required, such as the MAC802.11 encryption code, which
executes in sotfirq context, where SIMD processing is allowed on arm64.
Users of the async transform will keep the existing behavior.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This is a straight port to arm64/NEON of the x86 SSE3 implementation
of the ChaCha20 stream cipher. It uses the new skcipher walksize
attribute to process the input in strides of 4x the block size.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds support for DMA_ATTR_SKIP_CPU_SYNC attribute for
dma_{un}map_{page,sg} functions family to swiotlb.
DMA_ATTR_SKIP_CPU_SYNC allows platform code to skip synchronization of
the CPU cache for the given buffer assuming that it has been already
transferred to 'device' domain.
Ported from IOMMU .{un}map_{sg,page} ops.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Will Deacon <will.deacon@arm.com>
x86 has an option CONFIG_DEBUG_VIRTUAL to do additional checks
on virt_to_phys calls. The goal is to catch users who are calling
virt_to_phys on non-linear addresses immediately. This inclues callers
using virt_to_phys on image addresses instead of __pa_symbol. As features
such as CONFIG_VMAP_STACK get enabled for arm64, this becomes increasingly
important. Add checks to catch bad virt_to_phys usage.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
__pa_symbol is technically the marcro that should be used for kernel
symbols. Switch to this as a pre-requisite for DEBUG_VIRTUAL which
will do bounds checking.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
virt_to_pfn lacks a cast at the top level. Don't rely on __virt_to_phys
and explicitly cast to unsigned long.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Several macros for various x_to_y exist outside the bounds of an
__ASSEMBLY__ guard. Move them in preparation for support for
CONFIG_DEBUG_VIRTUAL.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Documentation for the infrastructure to expose CPU feature
register by emulating MRS.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Dave Martin <dave.martin@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This patch adds the hook for emulating MRS instruction to
export the 'user visible' value of supported system registers.
We emulate only the following id space for system registers:
Op0=3, Op1=0, CRn=0, CRm=[0, 4-7]
The rest will fall back to SIGILL. This capability is also
advertised via a new HWCAP_CPUID.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
[will: add missing static keyword to enable_mrs_emulation]
Signed-off-by: Will Deacon <will.deacon@arm.com>
HDMI converts RGB/I80 signal from DECON_TV to HDMI/TMDS video stream.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
DECON_TV is 2nd display controller on Exynos5433, used in HDMI path
or 2nd DSI path.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
In current code, the @changed always returns the last one's status for
the huge page with the contiguous bit set. This is really not what we
want. Even one of the PTEs is changed, we should tell it to the caller.
This patch fixes this issue.
Fixes: 66b3923a1a ("arm64: hugetlb: add support for PTE contiguous bit")
Cc: <stable@vger.kernel.org> # 4.5.x-
Signed-off-by: Huang Shijie <shijie.huang@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This adds the SCPI DVFS clock index and configures the CPU cores
accordingly.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
SCPI and SRAM are identical on GXBB and GXL. Moving the corresponding
nodes to meson-gx adds support for the thermal sensor on GXL based
devices.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
[khilman: add scpi_clocks label]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Address should not contain 0x prefix.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Track the user visible fields of a CPU feature register. This will be
used for exposing the value to the userspace. All the user visible
fields of a feature register will be passed on as it is, while the
others would be filled with their respective safe value.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Add a helper to extract the register field from a given
instruction.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Define helper macros to extract op0, op1, CRn, CRm & op2
for a given sys_reg id. While at it remove the explicit
masking only used for Op0.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Document the rules for choosing the safe value for different types
of features.
Cc: Dave Martin <dave.martin@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This patch does the following clean ups :
1) All undescribed fields of a register are now treated as 'strict'
with a safe value of 0. Hence we could leave an empty table for
describing registers which are RAZ.
2) ID_AA64DFR1_EL1 is RAZ and should use the table for RAZ register.
3) ftr_generic32 is used to represent a register with a 32bit feature
value. Rename this to ftr_singl32 to make it more obvious. Since
we don't have a 64bit singe feature register, kill ftr_generic.
Based on a patch by Mark Rutland.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
We currently have some RAZ fields described explicitly in our
arm64_ftr_bits arrays. These are inconsistently commented, grouped,
and/or applied, and maintaining these is error-prone.
Luckily, we don't need these at all. We'll never need to inspect RAZ
fields to determine feature support, and init_cpu_ftr_reg() will ensure
that any bits without a corresponding arm64_ftr_bits entry are treated
as RES0 with strict matching requirements. In check_update_ftr_reg()
we'll then compare these bits from the relevant cpuinfo_arm64
structures, and need not store them in a arm64_ftr_reg.
This patch removes the unnecessary arm64_ftr_bits entries for RES0 bits.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Any fields not defined in an arm64_ftr_bits entry are propagated to the
system-wide register value in init_cpu_ftr_reg(), and while we require
that these strictly match for the sanity checks, we don't update them in
update_cpu_ftr_reg().
Generally, the lack of an arm64_ftr_bits entry indicates that the bits
are currently RES0 (as is the case for the upper 32 bits of all
supposedly 32-bit registers).
A better default would be to use zero for the system-wide value of
unallocated bits, making all register checking consistent, and allowing
for subsequent simplifications to the arm64_ftr_bits arrays.
This patch updates init_cpu_ftr_reg() to treat unallocated bits as RES0
for the purpose of the system-wide safe value. These bits will still be
sanity checked with strict match requirements, as is currently the case.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The statistical profiling extension (SPE) is an optional feature of
ARMv8.1 and is unlikely to be supported by all of the CPUs in a
heterogeneous system.
This patch updates the cpufeature checks so that such systems are not
tainted as unsupported.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Suzuki Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Perf already supports multiple PMU instances for heterogeneous systems,
so there's no need to be strict in the cpufeature checking, particularly
as the PMU extension is optional in the architecture.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Since its introduction, the UAO enable call was broken, and useless.
commit 2a6dcb2b5f ("arm64: cpufeature: Schedule enable() calls instead
of calling them via IPI"), fixed the framework so that these calls
are scheduled, so that they can modify PSTATE.
Now it is just useless. Remove it. UAO is enabled by the code patching
which causes get_user() and friends to use the 'ldtr' family of
instructions. This relies on the PSTATE.UAO bit being set to match
addr_limit, which we do in uao_thread_switch() called via __switch_to().
All that is needed to enable UAO is patch the code, and call schedule().
__apply_alternatives_multi_stop() calls stop_machine() when it modifies
the kernel text to enable the alternatives, (including the UAO code in
uao_thread_switch()). Once stop_machine() has finished __switch_to() is
called to reschedule the original task, this causes PSTATE.UAO to be set
appropriately. An explicit enable() call is not needed.
Reported-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
In commit 23c8a500c2 ("arm64: kernel: use ordinary return/argument
register for el2_setup()"), we stopped using w20 as a global stash of
the boot mode flag, and instead pass this around in w0 as a function
parameter.
Unfortunately, we missed a couple of comments, which still refer to the
old convention of using w20/x20.
This patch fixes up the comments to describe the code as it currently
works.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
A few printk calls in arm64 omit a trailing newline, even though there
is no subsequent KERN_CONT printk associated with them, and we actually
want a newline.
This can result in unrelated lines being appended, rather than appearing
on a new line. Additionally, timestamp prefixes may appear in-line. This
makes the logs harder to read than necessary.
Avoid this by adding a trailing newline.
These were found with a shortlist generated by:
$ git grep 'pr\(intk\|_.*\)(.*)' -- arch/arm64 | grep -v pr_fmt | grep -v '\\n"'
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
CC: James Morse <james.morse@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Function graph tracer shows negative time (wrap around) when tracing
__switch_to if the nosleep-time trace option is enabled.
Time compensation for nosleep-time is done by an ftrace probe on
sched_switch. This doesn't work well for the following events (with
letters representing timestamps):
A - sched switch probe called for task T switch out
B - __switch_to calltime is recorded
C - sched_switch probe called for task T switch in
D - __switch_to rettime is recorded
If C - A > D - B, then we end up over compensating for the time spent in
__switch_to giving rise to negative times in the trace output.
On x86, __switch_to is not traced if function graph tracer is enabled.
Do the same for arm64 as well.
Cc: Todd Kjos <tkjos@google.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Joel Fernandes <joelaf@google.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
* Add PWM, and sound MIX and CTU support to r8a7795 SoC
* Add CAN, CAN FD and all MSIOF nodes to r8a7796 SoC
* Use Gen 3 fallback binding for i2c, msiof, PCIE and USB2 phy
* Enable Ethernet and 4 GiB memory on r8a7796/salvator-x board
* Add r8a7796/salvator-x board part number to bindings
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=s00S
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm64-dt-for-v4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt64
Renesas ARM64 Based SoC DT Updates for v4.11
* Add PWM, and sound MIX and CTU support to r8a7795 SoC
* Add CAN, CAN FD and all MSIOF nodes to r8a7796 SoC
* Use Gen 3 fallback binding for i2c, msiof, PCIE and USB2 phy
* Enable Ethernet and 4 GiB memory on r8a7796/salvator-x board
* Add r8a7796/salvator-x board part number to bindings
* tag 'renesas-arm64-dt-for-v4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: r8a7795: Add PWM support
arm64: dts: r8a7796: Use R-Car Gen 3 fallback binding for msiof nodes
arm64: dts: r8a7796: salvator-x: Enable EthernetAVB
arm64: dts: renesas: r8a7796: Add EthernetAVB instance
arm64: dts: r8a7796: salvator-x: Update memory node to 4 GiB map
arm64: dts: r8a7796: Use R-Car Gen 3 fallback binding for i2c nodes
arm64: dts: r8a7795: Use R-Car Gen 3 fallback binding for i2c nodes
arm64: dts: r8a7795: Use Gen 3 fallback compat string for PCIE
arm64: dts: r8a7795: add sound MIX support
arm64: dts: r8a7795: add sound CTU support
arm64: dts: r8a7795: Use renesas,rcar-gen3-usb2-phy fallback binding
arm64: renesas: r8a7796/salvator-x: Add board part number to DT bindings
arm64: dts: r8a7796: Add CAN FD support
arm64: dts: r8a7796: Add CAN support
arm64: dts: r8a7796: Add CAN external clock support
arm64: dts: r8a7796: Add all MSIOF nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
Tree-wide replacement was done by commit 2ef7d5f342 ("ARM, ARM64:
dts: drop "arm,amba-bus" in favor of "simple-bus"), then the 2nd
round by commit 15b7cc78f0 ("arm64: dts: drop "arm,amba-bus" in
favor of "simple-bus" part 2").
Here, some new users have appeared for Linux v4.10-rc1. Eliminate
them now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
LS1012A features an advanced 64-bit ARM v8 CortexA53 processor
with 32 KB of parity protected L1-I cache, 32 KB of ECC protected
L1-D cache, as well as 256 KB of ECC protected L2 cache.
Features summary
One 64-bit ARM-v8 Cortex-A53 core with the following capabilities
- Arranged as a cluster of one core supporting a 256 KB L2 cache with ECC
protection
- Speed up to 800 MHz
- Parity-protected 32 KB L1 instruction cache and 32 KB L1 data cache
- Neon SIMD engine
- ARM v8 cryptography extensions
One 16-bit DDR3L SDRAM memory controller
ARM core-link CCI-400 cache coherent interconnect
Cryptography acceleration (SEC)
One Configurable x3 SerDes
One PCI Express Gen2 controller, supporting x1 operation
One serial ATA (SATA Gen 3.0) controller
One USB 3.0/2.0 controller with integrated PHY
Following levels of DTSI/DTS files have been created for the LS1012A
SoC family:
- fsl-ls1012a.dtsi:
DTS-Include file for FSL LS1012A SoC.
- fsl-ls1012a-frdm.dts:
DTS file for FSL LS1012A FRDM board.
- fsl-ls1012a-qds.dts:
DTS file for FSL LS1012A QDS board.
- fsl-ls1012a-rdb.dts:
DTS file for FSL LS1012A RDB board.
Signed-off-by: Harninder Rai <harninder.rai@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull swiotlb fixes from Konrad Rzeszutek Wilk:
"This has one fix to make i915 work when using Xen SWIOTLB, and a
feature from Geert to aid in debugging of devices that can't do DMA
outside the 32-bit address space.
The feature from Geert is on top of v4.10 merge window commit
(specifically you pulling my previous branch), as his changes were
dependent on the Documentation/ movement patches.
I figured it would just easier than me trying than to cherry-pick the
Documentation patches to satisfy git.
The patches have been soaking since 12/20, albeit I updated the last
patch due to linux-next catching an compiler error and adding an
Tested-and-Reported-by tag"
* 'stable/for-linus-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb:
swiotlb: Export swiotlb_max_segment to users
swiotlb: Add swiotlb=noforce debug option
swiotlb: Convert swiotlb_force from int to enum
x86, swiotlb: Simplify pci_swiotlb_detect_override()
Currently TM2E dts includes TM2 but there are some differences
between the two boards and TM2 has some properties that TM2E
doesn't have.
That's why it's important to keep the two dts files independent
and put all the commonalities in a tm2-common.dtsi file.
At the current status the only two differences between the two
dts files (besides the board name) are ldo31 and ldo38.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch fixes wrong values assigned to ldo23 and ldo25 on both TM2 and TM2E.
Fixes: 01e5d23521 ("arm64: dts: exynos: Add dts file for Exynos5433-based TM2 board")
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Per the errata of TRM, rk3399 won't support gen2 from
now on, so let's set max-link-speed to 1 in order not
to doing training for gen2.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Change the PIN() macro definition so that it can use the macros
from pinctrl/samsung.h header file.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Use the macros defined in include/dt-bindings/pinctrl/samsung.h
instead of hardcoded values.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
A64 has a MUSB controller wired to the USB PHY 0, which is connected
to the upper USB Type-A port of Pine64.
As the port is a Type-A female port, enable it in host-only mode in the
device tree, which makes devices with USB Type-A male port can work on
this port (which is originally designed by Pine64 team).
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner A64 SoC has a MUSB controller like the one in A33, so add
a node for it, just use the compatible of A33 MUSB.
Host mode is tested to work properly on Pine64 and will be added into
the device tree of Pine64 in next patch.
Peripheral mode is also tested on Pine64, by changing dr_mode property
of usb_otg node and use a non-standard USB Type-A to Type-A cable.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Pine64 have two USB Type-A ports, which are wired to the two ports of
A64 USB PHY, and the lower port is the EHCI/OHCI1 port.
Enable the necessary nodes to enable the lower USB port to work.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In this dts file, uart0 node is put before i2c1.
Move the uart0 node to the end to satisfy alphebetical order.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner A64 have two HCI USB controllers, a OTG controller and a USB
PHY device which have two ports. One of the port is wired to both a HCI
USB controller and the OTG controller, which is currently not supported.
The another one is only wired to a HCI controller, and the device node of
OHCI/EHCI controller of the port can be added now.
Also the A64 USB PHY device node is also added for the HCI controllers to
work.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Commit c02433dd6d ("arm64: split thread_info from task stack")
inverted the relationship between get_current() and
current_thread_info(), with sp_el0 now holding the current task_struct
rather than the current thead_info. The new implementation of
get_current() prevents the compiler from being able to optimize repeated
calls to either, resulting in a noticeable penalty in some
microbenchmarks.
This patch restores the previous optimisation by implementing
get_current() in the same way as our old current_thread_info(), using a
non-volatile asm statement.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reported-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Recent changes made KERN_CONT mandatory for continued lines. In the
absence of KERN_CONT, a newline may be implicit inserted by the core
printk code.
In show_pte, we (erroneously) use printk without KERN_CONT for continued
prints, resulting in output being split across a number of lines, and
not matching the intended output, e.g.
[ff000000000000] *pgd=00000009f511b003
, *pud=00000009f4a80003
, *pmd=0000000000000000
Fix this by using pr_cont() for all the continuations.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
- DT: GXL: fix GPIO include
- add DT and defconfig for newly merged DRM driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJYbIZJAAoJEFk3GJrT+8ZlDb0P/1nnnbnxYP2IQzI+XggSLACq
DznCawJmzJaYtvq8LM/BqfIoQW2x32VG5G1a1FYbbv4hySOa5Q5hFwN4/eUSQJq8
nT5fFCwRFl4G2u6fdlBiNUxmN+iguCbY8uAYfVQcsWJ8CUtHjdZnpvopXM8nB0/x
tbOh8rhN042q5SMq74STeBR+YeJyVN9osa8lChL3rVqTuvEHYDScUgDjx2grXzVw
K9rqoEKL/qMN7HWpa/O2hEEvO0sR5UXbB5KIa3j47Vxf7dVRRvPE8fU4mAqqRgxo
NSpceF1YmB90AG+7x8z8ndxJXHbP4DwcJwvwSD+bvuKEBsbfCHuPqQE5lzFSM+Kn
j21NEH7x8tKmKWeoCX2o+mHjn4B3y4SpDnot8CQ/l9nqQxrgxF7u05PckBauprGL
7K/txdS1xYAJ42pBymtgwXzZajaHfLu1i5PA+Fuq80g8VBCgTopv+syAZfSwU/xn
vF8bASfwQYYnVfF05z2K7chyHJiVLdCnIrRQzaHb7QcCMYnhTm9YrVyQ5UXsOaIz
WI2u5ptZUFYs2HGLm3M78IZtN9Ash3XAnrPAR+0R2DF2tyE2686scn/uakcFhVJt
oojrtkmHUbQih48yzI41EtLlviJ41hzykMknzqVfUs4eQayYBayGNAUefFBOwFZb
4JgW2I/SwficH0zKHK/Y
=7ngo
-----END PGP SIGNATURE-----
Merge tag 'amlogic-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into fixes
Pull "Amlogic fixes for v4.10" from Kevin Hilman:
- DT: GXL: fix GPIO include
- add DT and defconfig for newly merged DRM driver
This pull has one real fix, as a couple non-critical ones. The DRM
DT/defconfig patches are coming now because I didn't expect the new
driver to make it for the v4.10 merge window, but since it did[1], the
DT and defconfig should go into the same release.
[1] bbbe775ec5 drm: Add support for Amlogic Meson Graphic Controller
* tag 'amlogic-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM64: defconfig: enable DRM_MESON as module
ARM64: dts: meson-gx: Add Graphic Controller nodes
ARM64: dts: meson-gxl: fix GPIO include
A simple fix to extend GICv2 CPU interface registers from 4K to 8K
on AEMv8 FVP/RTSM models in order to support split priority drop and
interrupt deactivation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=BoKJ
-----END PGP SIGNATURE-----
Merge tag 'juno-fixes-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into fixes
Pull "ARMv8 Juno/VExpress fixes for v4.10" from Sudeep Holla:
A simple fix to extend GICv2 CPU interface registers from 4K to 8K
on AEMv8 FVP/RTSM models in order to support split priority drop and
interrupt deactivation.
* tag 'juno-fixes-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: vexpress: Support GICC_DIR operations
* Provide sd0_uhs node
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XZkS
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes-for-v4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Renesas ARM Based SoC Fixes for v4.10
* Provide sd0_uhs node
* tag 'renesas-fixes-for-v4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: h3ulcb: Provide sd0_uhs node
Add the 7 PWM channels to the r8a7795 device tree, in the disabled
state.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The BCM958712DxXMC board is a smaller form factor typically used as
controller boards for switches. This smaller board has less devices
pinned out, so only a few need be populated in the device tree.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Nitro firmware is loaded into memory by the bootloader at a specific
location. Set this memory range aside to prevent the kernel from using
it.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This enables the PAXC based PCIe root complex on NS2 SVK. The PAXC based
root complex is connected to internally emulated PCIe endpoints
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
PAXB and PAXC PCIe interfaces on NS2 have been using the iProc event
queue to handle MSI. With the gicv2m support ready, we should now switch
to gicv2m for MSI handling
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add Video Processing Unit and CVBS Output nodes, and enable CVBS on selected
boards.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This commit enables the XORv2 DMA driver, which is used on the ARM64
Marvell Armada 7K and 8K platforms.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The license text has been mangled at some point then copy pasted across
multiple files. Restore it to what it should be.
Note that this is not intended as a license change.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Armada 3700 has two i2c bus interface units, this commit adds the
definitions of the corresponding device nodes. It also enables the node
on the development board for this SoC.
Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit enables the device node spi0 on the official development
board for the Marvell Armada 3700. It also adds sub-node for the 128Mb
SPI-NOR present on the board.
Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Armada 3700 SoC has an SPI Controller, this commit adds the definition
of the SPI device node at the SoC level.
Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This defines and enables the Marvell ethernet switch MVE886341 on the
Marvell ESPRESSObin board.
Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Use recently added R-Car Gen 3 fallback binding for msiof nodes in
DT for r8a7796 SoC.
This has no run-time effect for the current driver as the initialisation
sequence is the same for the SoC-specific binding for r8a7796 and the
fallback binding for R-Car Gen 3.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch updates memory region:
- After changes, the new map of the Salvator-X board on R8A7796 SoC
Bank0: 2GiB RAM : 0x000048000000 -> 0x000bfffffff
Bank1: 2GiB RAM : 0x000600000000 -> 0x0067fffffff
- Before changes, the old map looked like this:
Bank0: 2GiB RAM : 0x000048000000 -> 0x000bfffffff
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Correct size of old map]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use recently added R-Car Gen 3 fallback binding for i2c nodes in
DT for r8a7796 SoC.
This has no run-time effect for the current driver as the initialisation
sequence is the same for the SoC-specific binding for r8a7796 and the
fallback binding for R-Car Gen 3.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Use recently added R-Car Gen 3 fallback binding for i2c nodes in
DT for r8a7795 SoC.
This has no run-time effect for the current driver as the initialisation
sequence is the same for the SoC-specific binding for r8a7795 and the
fallback binding for R-Car Gen 3.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Use recently added en 3 fallback compat string for PCIE
in r8a7795 DT.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds CTU (= Channel Transfer Unit) support which is needed
to sound mixing.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
A fallback binding for the Renesas R-Car Gen3 for USB2.0 PHY driver was
added by commit cde7bc367f ("phy: rcar-gen3-usb2: add fallback binding").
This patch makes use of this binding in the DT for the r8a7795 SoC.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Adds CAN FD controller node for r8a7796.
Based on a patch for r8a7795 by Ramesh Shanmugasundaram.
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adds CAN controller nodes for r8a7796.
Based on a patch for r8a7795 by Ramesh Shanmugasundaram.
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adds external CAN clock node for r8a7796. This clock can be used as
fCAN clock of CAN and CAN FD controller.
Based on a patch for r8a7795 by Ramesh Shanmugasundaram.
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device nodes for all MSIOF SPI controllers.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds the CPU clock phandle in CPU's node
and uses operating-points-v2 to register operating points.
So it can be used by cpufreq-dt driver.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
pca9547 won't probed since its status property is disabled.
while there are devices connected to it, we need remove status
property to let ds3232 and adt7461 probed correctly.
Signed-off-by: Meng Yi <meng.yi@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds the bus Device-tree nodes for INT (Internal) block
and enables the bus frequency scaling.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds the AMBA AXI bus nodes using VDD_INT for Exynos5433 SoC.
Following list specify the detailed correlation between sub-block and clock:
- CLK_ACLK_G2D_{400|266} : Bus clock for G2D (2D graphic engine)
- CLK_ACLK_MSCL_400 : Bus clock for MSCL (Memory to memory Scaler)
- CLK_ACLK_GSCL_333 : Bus clock for GSCL (General Scaler)
- CLK_SCLK_JPEG_MSCL : Bus clock for JPEG
- CLK_ACLK_MFC_400 : Bus clock for MFC (Multi Format Codec)
- CLK_ACLK_HEVC_400 : Bus clock for HEVC (High Efficient Video Codec)
- CLK_ACLK_BUS0_400 : NoC's (Network On Chip) bus clock for PERIC/PERIS/FSYS/MSCL
- CLK_ACLK_BUS1_400 : NoC's bus clock for MFC/HEVC/G3D
- CLK_ACLK_BUS2_400 : NoC's bus clock for GSCL/DISP/G2D/CAM0/CAM1/ISP
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds PPMU (Platform Performance Monitoring Unit) Device-tree node
to measure the utilization of each IP in Exynos SoC.
- PPMU_D{0|1}_CPU are used to measure the utilization of MIF (Memory Interface)
block with VDD_MIF power source.
- PPMU_D{0|1}_GENERAL are used to measure the utilization of INT(Internal)
block with VDD_INT power source.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Use macros to describe gpios will make the dts easier to
read and write.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
[converted interrupt-gpios and new rk3399-evb backlight]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We found that the suspend process was blocked when it run into
ehci/ohci module due to clk-480m of usb2-phy was disabled.
The root cause is that usb2-phy suspended earlier than ehci/ohci
(usb2-phy will be auto suspended if no devices plug-in). and the
clk-480m provided by it was disabled if no module used. However,
some suspend process related ehci/ohci are base on this clock,
so we should refer it into ehci/ohci driver to prevent this case.
The u2phy clock flow like this:
===
u2phy ________________
| | |-----> UTMI_CLK ---------> | EHCI |
OSC_24M ---|---> PHY_PLL----|----|
|________^_______| |-----> 480M_CLK ---|G|---> | USBPHY_480M_SRC| ----> USBPHY_480M for SoC
|
|
GRF
===
Signed-off-by: William wu <wulf@rock-chips.com>
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We haven't enabled eDP support yet, but we might as well describe the
pin now.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We're going to need to amend this table in board files.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Zynq Ultrascale MP uses version 1.4 of the Cadence IP core
which fixes some silicon bugs that needed software workarounds
in Version 1.0 that was used on Zynq systems.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
Cc: Rob Herring <robh+dt@kernel.org>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The patch removes these warnings reported by dtc 1.4:
Warning (unit_address_vs_reg): Node /amba_apu has a reg or ranges
property, but no unit name
Warning (unit_address_vs_reg): Node /memory has a reg or ranges
property, but no unit name
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The GICv2 CPU interface registers span across 8K, not 4K as indicated in
the DT. Only the GICC_DIR register is located after the initial 4K
boundary, leaving a functional system but without support for separately
EOI'ing and deactivating interrupts.
After this change the system supports split priority drop and interrupt
deactivation. This patch is based on similar one from Christoffer Dall:
commit 368400e242 ("ARM: dts: vexpress: Support GICC_DIR operations")
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
This patch adds required memory carveouts so that the kernel does not
access memory that is in use or has been reserved for use by other remote
processors.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Pull SMP hotplug notifier removal from Thomas Gleixner:
"This is the final cleanup of the hotplug notifier infrastructure. The
series has been reintgrated in the last two days because there came a
new driver using the old infrastructure via the SCSI tree.
Summary:
- convert the last leftover drivers utilizing notifiers
- fixup for a completely broken hotplug user
- prevent setup of already used states
- removal of the notifiers
- treewide cleanup of hotplug state names
- consolidation of state space
There is a sphinx based documentation pending, but that needs review
from the documentation folks"
* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/armada-xp: Consolidate hotplug state space
irqchip/gic: Consolidate hotplug state space
coresight/etm3/4x: Consolidate hotplug state space
cpu/hotplug: Cleanup state names
cpu/hotplug: Remove obsolete cpu hotplug register/unregister functions
staging/lustre/libcfs: Convert to hotplug state machine
scsi/bnx2i: Convert to hotplug state machine
scsi/bnx2fc: Convert to hotplug state machine
cpu/hotplug: Prevent overwriting of callbacks
x86/msr: Remove bogus cleanup from the error path
bus: arm-ccn: Prevent hotplug callback leak
perf/x86/intel/cstate: Prevent hotplug callback leak
ARM/imx/mmcd: Fix broken cpu hotplug handling
scsi: qedi: Convert to hotplug state machine
When the state names got added a script was used to add the extra argument
to the calls. The script basically converted the state constant to a
string, but the cleanup to convert these strings into meaningful ones did
not happen.
Replace all the useless strings with 'subsys/xxx/yyy:state' strings which
are used in all the other places already.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/20161221192112.085444152@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Move some Linux-specific functionality to upstream ACPICA and
update the in-kernel users of it accordingly (Lv Zheng).
- Drop a useless warning (triggered by the lack of an optional
object) from the ACPI namespace scanning code (Zhang Rui).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=55TG
-----END PGP SIGNATURE-----
Merge tag 'acpi-extra-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"Here are new versions of two ACPICA changes that were deferred
previously due to a problem they had introduced, two cleanups on top
of them and the removal of a useless warning message from the ACPI
core.
Specifics:
- Move some Linux-specific functionality to upstream ACPICA and
update the in-kernel users of it accordingly (Lv Zheng)
- Drop a useless warning (triggered by the lack of an optional
object) from the ACPI namespace scanning code (Zhang Rui)"
* tag 'acpi-extra-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / osl: Remove deprecated acpi_get_table_with_size()/early_acpi_os_unmap_memory()
ACPI / osl: Remove acpi_get_table_with_size()/early_acpi_os_unmap_memory() users
ACPICA: Tables: Allow FADT to be customized with virtual address
ACPICA: Tables: Back port acpi_get_table_with_size() and early_acpi_os_unmap_memory() from Linux kernel
ACPI: do not warn if _BQC does not exist
* acpica:
ACPI / osl: Remove deprecated acpi_get_table_with_size()/early_acpi_os_unmap_memory()
ACPI / osl: Remove acpi_get_table_with_size()/early_acpi_os_unmap_memory() users
ACPICA: Tables: Allow FADT to be customized with virtual address
ACPICA: Tables: Back port acpi_get_table_with_size() and early_acpi_os_unmap_memory() from Linux kernel
* acpi-scan:
ACPI: do not warn if _BQC does not exist
Since all users are cleaned up, remove the 2 deprecated APIs due to no
users.
As a Linux variable rather than an ACPICA variable, acpi_gbl_permanent_mmap
is renamed to acpi_permanent_mmap to have a consistent coding style across
entire Linux ACPI subsystem.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch removes the users of the deprectated APIs:
acpi_get_table_with_size()
early_acpi_os_unmap_memory()
The following APIs should be used instead of:
acpi_get_table()
acpi_put_table()
The deprecated APIs are invented to be a replacement of acpi_get_table()
during the early stage so that the early mapped pointer will not be stored
in ACPICA core and thus the late stage acpi_get_table() won't return a
wrong pointer. The mapping size is returned just because it is required by
early_acpi_os_unmap_memory() to unmap the pointer during early stage.
But as the mapping size equals to the acpi_table_header.length
(see acpi_tb_init_table_descriptor() and acpi_tb_validate_table()), when
such a convenient result is returned, driver code will start to use it
instead of accessing acpi_table_header to obtain the length.
Thus this patch cleans up the drivers by replacing returned table size with
acpi_table_header.length, and should be a no-op.
Reported-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Convert the flag swiotlb_force from an int to an enum, to prepare for
the advent of more possible values.
Suggested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Pull x86 fixes and cleanups from Thomas Gleixner:
"This set of updates contains:
- Robustification for the logical package managment. Cures the AMD
and virtualization issues.
- Put the correct start_cpu() return address on the stack of the idle
task.
- Fixups for the fallout of the nodeid <-> cpuid persistent mapping
modifciations
- Move the x86/MPX specific mm_struct member to the arch specific
mm_context where it belongs
- Cleanups for C89 struct initializers and useless function
arguments"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/floppy: Use designated initializers
x86/mpx: Move bd_addr to mm_context_t
x86/mm: Drop unused argument 'removed' from sync_global_pgds()
ACPI/NUMA: Do not map pxm to node when NUMA is turned off
x86/acpi: Use proper macro for invalid node
x86/smpboot: Prevent false positive out of bounds cpumask access warning
x86/boot/64: Push correct start_cpu() return address
x86/boot/64: Use 'push' instead of 'call' in start_cpu()
x86/smpboot: Make logical package management more robust
-----BEGIN PGP SIGNATURE-----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=ADpU
-----END PGP SIGNATURE-----
Merge tag 'media/v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new Mediatek drivers: mtk-mdp and mtk-vcodec
- some additions at the media documentation
- the CEC core and drivers were promoted from staging to mainstream
- some cleanups at the DVB core
- the LIRC serial driver got promoted from staging to mainstream
- added a driver for Renesas R-Car FDP1 driver
- add DVBv5 statistics support to mn88473 driver
- several fixes related to printk continuation lines
- add support for HSV encoding formats
- lots of other cleanups, fixups and driver improvements.
* tag 'media/v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (496 commits)
[media] v4l: tvp5150: Add missing break in set control handler
[media] v4l: tvp5150: Don't inline the tvp5150_selmux() function
[media] v4l: tvp5150: Compile tvp5150_link_setup out if !CONFIG_MEDIA_CONTROLLER
[media] em28xx: don't store usb_device at struct em28xx
[media] em28xx: use usb_interface for dev_foo() calls
[media] em28xx: don't change the device's name
[media] mn88472: fix chip id check on probe
[media] mn88473: fix chip id check on probe
[media] lirc: fix error paths in lirc_cdev_add()
[media] s5p-mfc: Add support for MFC v8 available in Exynos 5433 SoCs
[media] s5p-mfc: Rework clock handling
[media] s5p-mfc: Don't keep clock prepared all the time
[media] s5p-mfc: Kill all IS_ERR_OR_NULL in clocks management code
[media] s5p-mfc: Remove dead conditional code
[media] s5p-mfc: Ensure that clock is disabled before turning power off
[media] s5p-mfc: Remove special clock rate management
[media] s5p-mfc: Use printk_ratelimited for reporting ioctl errors
[media] s5p-mfc: Set DMA_ATTR_ALLOC_SINGLE_PAGES
[media] vivid: Set color_enc on HSV formats
[media] v4l2-tpg: Init hv_enc field with a valid value
...
Driver updates for ARM SoCs, including a couple of newly added drivers:
- A new driver for the power management controller on TI Keystone
- Support for the prerelease "SCPI" firmware protocol that ended up
being shipped by Amlogic in their GXBB SoC.
- A soc_device can now be matched using a glob from inside the
kernel, when another driver wants to know the specific chip
it is running on and cannot find out from DT, firmware or hardware.
- Renesas SoCs now support identification through the soc_device
interface, both in user space and kernel.
- Renesas r8a7743 and r8a7745 gain support for their system controller
- A new checking module for the ARM "PSCI" (not to be confused
with "SCPI" mentioned above) firmware interface.
- A new driver for the Tegra GMI memory interface
- Support for the Tegra firmware interfaces with their
power management controllers
As usual, the updates for the reset controller framework are merged
here, as they tend to touch multiple SoCs as well, including a new
driver for the Oxford (now Broadcom) OX820 chip and the Tegra
bpmp interface.
The existing drivers for Atmel, Qualcomm, NVIDIA, TI Davinci, and
Rockchips SoCs see some further updates.
Conflicts:
- ARCH_RENESAS now selects SOC_BUS, but no longer needs GPIOLIB
- drivers/soc/renesas/Makefile: multiple files got added, keep
all in logical sorting
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6dP8
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, including a couple of newly added
drivers:
- A new driver for the power management controller on TI Keystone
- Support for the prerelease "SCPI" firmware protocol that ended up
being shipped by Amlogic in their GXBB SoC.
- A soc_device can now be matched using a glob from inside the
kernel, when another driver wants to know the specific chip it is
running on and cannot find out from DT, firmware or hardware.
- Renesas SoCs now support identification through the soc_device
interface, both in user space and kernel.
- Renesas r8a7743 and r8a7745 gain support for their system
controller
- A new checking module for the ARM "PSCI" (not to be confused with
"SCPI" mentioned above) firmware interface.
- A new driver for the Tegra GMI memory interface
- Support for the Tegra firmware interfaces with their power
management controllers
As usual, the updates for the reset controller framework are merged
here, as they tend to touch multiple SoCs as well, including a new
driver for the Oxford (now Broadcom) OX820 chip and the Tegra bpmp
interface.
The existing drivers for Atmel, Qualcomm, NVIDIA, TI Davinci, and
Rockchips SoCs see some further updates"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (76 commits)
misc: sram: remove useless #ifdef
drivers: psci: Allow PSCI node to be disabled
drivers: psci: PSCI checker module
soc: renesas: Identify SoC and register with the SoC bus
firmware: qcom: scm: Return PTR_ERR when devm_clk_get fails
firmware: qcom: scm: Remove core, iface and bus clocks dependency
dt-bindings: firmware: scm: Add MSM8996 DT bindings
memory: da8xx-ddrctl: drop the call to of_flat_dt_get_machine_name()
bus: da8xx-mstpri: drop the call to of_flat_dt_get_machine_name()
ARM: shmobile: Document DT bindings for Product Register
soc: renesas: rcar-sysc: add R8A7745 support
reset: Add Tegra BPMP reset driver
dt-bindings: firmware: Allow child nodes inside the Tegra BPMP
dt-bindings: Add power domains to Tegra BPMP firmware
firmware: tegra: Add BPMP support
firmware: tegra: Add IVC library
dt-bindings: firmware: Add bindings for Tegra BPMP
mailbox: tegra-hsp: Use after free in tegra_hsp_remove_doorbells()
mailbox: Add Tegra HSP driver
firmware: arm_scpi: add support for pre-v1.0 SCPI compatible
...
A couple of interesting new SoC platforms are now supported, these are
the respective DTS sources:
- Samsung Exynos5433 mobile phone platform, including an (almost) fully
supported phone reference board.
- Hisilicon Hip07 server platform and D05 board, the latest iteration
of their product line, now with 64 Cortex-A72 cores across two
sockets.
- Allwinner A64 SoC, the first 64-bit chip from their "sunxi" product
line, used in Android tablets and ultra-cheap development boards
- NXP LS1046A Communication processor, improving on the earlier LS1043A
with faster CPU cores
- Qualcomm MSM8992 (Snapdragon 808) and MSM8994 (Snapdragon 810)
mobile phone SoCs
- Early support for the Nvidia Tegra Tegra186 SoC
- Amlogic S905D is a minor variant of their existing Android consumer
product line
- Rockchip PX5 automotive platform, a close relative of their popular
rk3368 Android tablet chips
Aside from the respective evaluation platforms for the above
chips, there are only a few consumer devices and boards added
this time:
- Huawei Nexus 6P (Angler) mobile phone
- LG Nexus 5x (Bullhead) mobile phone
- Nexbox A1 and A95X Android TV boxes
- Pine64 development board based on Allwinner A64
- Globalscale Marvell ESPRESSOBin community board based on Armada 3700
- Renesas "R-Car Starter Kit Pro" (M3ULCB) low-cost automotive board
For the existing platforms, we get bug fixes and new peripheral support
for Juno, Renesas, Uniphier, Amlogic, Samsung, Broadcom, Rockchip, Berlin,
and ZTE.
Conflicts:
- Documentation/devicetree/bindings/arm/shmobile.txt: a
rename/add conflict, keep both modifications and maintain
alphabetical ordering.
- arch/arm64/boot/dts/*/*.dtsi: nodes were added in netdev,
mmc and clk, keep both sides in each case.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=geT0
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Arnd Bergmann:
"A couple of interesting new SoC platforms are now supported, these are
the respective DTS sources:
- Samsung Exynos5433 mobile phone platform, including an (almost)
fully supported phone reference board.
- Hisilicon Hip07 server platform and D05 board, the latest iteration
of their product line, now with 64 Cortex-A72 cores across two
sockets.
- Allwinner A64 SoC, the first 64-bit chip from their "sunxi" product
line, used in Android tablets and ultra-cheap development boards
- NXP LS1046A Communication processor, improving on the earlier
LS1043A with faster CPU cores
- Qualcomm MSM8992 (Snapdragon 808) and MSM8994 (Snapdragon 810)
mobile phone SoCs
- Early support for the Nvidia Tegra Tegra186 SoC
- Amlogic S905D is a minor variant of their existing Android consumer
product line
- Rockchip PX5 automotive platform, a close relative of their popular
rk3368 Android tablet chips
Aside from the respective evaluation platforms for the above chips,
there are only a few consumer devices and boards added this time:
- Huawei Nexus 6P (Angler) mobile phone
- LG Nexus 5x (Bullhead) mobile phone
- Nexbox A1 and A95X Android TV boxes
- Pine64 development board based on Allwinner A64
- Globalscale Marvell ESPRESSOBin community board based on Armada 3700
- Renesas "R-Car Starter Kit Pro" (M3ULCB) low-cost automotive board
For the existing platforms, we get bug fixes and new peripheral
support for Juno, Renesas, Uniphier, Amlogic, Samsung, Broadcom,
Rockchip, Berlin, and ZTE"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (168 commits)
arm64: dts: fix build errors from missing dependencies
ARM64: dts: meson-gxbb: add SCPI pre-1.0 compatible
ARM64: dts: meson-gxl: Add support for Nexbox A95X
ARM64: dts: meson-gxm: Add support for the Nexbox A1
ARM: dts: artpec: add pcie support
arm64: dts: berlin4ct-dmp: add missing unit name to /memory node
arm64: dts: berlin4ct-stb: add missing unit name to /memory node
arm64: dts: berlin4ct: add missing unit name to /soc node
arm64: dts: qcom: msm8916: Add ddr support to sdhc1
arm64: dts: exynos: Enable HS400 mode for eMMC for TM2
ARM: dts: Add xo to sdhc clock node on qcom platforms
ARM64: dts: Add support for Meson GXM
dt-bindings: add rockchip RK1108 Evaluation board
arm64: dts: NS2: Add PCI PHYs
arm64: dts: NS2: enable sdio1
arm64: dts: exynos: Add the mshc_2 node for supporting T-Flash
arm64: tegra: Add NVIDIA P2771 board support
arm64: tegra: Enable PSCI on P3310
arm64: tegra: Add NVIDIA P3310 processor module support
arm64: tegra: Add GPIO controllers on Tegra186
...
Lots of changes as usual, so I'm trying to be brief here. Most of the
new hardware support has the respective driver changes merged through
other trees or has had it available for a while, so this is where things
come together.
We get a DT descriptions for a couple of new SoCs, all of them variants
of other chips we already support, and usually coming with a new
evaluation board:
- Oxford semiconductor (now Broadcom) OX820 SoC for NAS devices
- Qualcomm MDM9615 LTE baseband
- NXP imx6ull, the latest and smallest i.MX6 application processor variant
- Renesas RZ/G (r8a7743 and r8a7745) application processors
- Rockchip PX3, a variant of the rk3188 chip used in Android tablets
- Rockchip rk1108 single-core application processor
- ST stm32f746 Cortex-M7 based microcontroller
- TI DRA71x automotive processors
These are commercially available consumer platforms we now support:
- Motorola Droid 4 (xt894) mobile phone
- Rikomagic MK808 Android TV stick based on Rockchips rx3066
- Cloud Engines PogoPlug v3 based on OX820
- Various Broadcom based wireless devices:
- Netgear R8500 router
- Tenda AC9 router
- TP-LINK Archer C9 V1
- Luxul XAP-1510 Access point
- Turris Omnia open hardware router based on Armada 385
And a couple of new boards targeted at developers, makers
or industrial integration:
- Macnica Sodia development platform for Altera socfpga (Cyclone V)
- MicroZed board based on Xilinx Zynq FPGA platforms
- TOPEET itop/elite based on exynos4412
- WP8548 MangOH Open Hardware platform for IOT, based on
Qualcomm MDM9615
- NextThing CHIP Pro gadget
- NanoPi M1 development board
- AM571x-IDK industrial board based on TI AM5718
- i.MX6SX UDOO Neo
- Boundary Devices Nitrogen6_SOM2 (i.MX6)
- Engicam i.CoreM6
- Grinn i.MX6UL liteSOM/liteBoard
- Toradex Colibri iMX6 module
Other changes:
- added peripherals on renesas, davinci, stm32f429, uniphier, sti,
mediatek, integrator, at91, imx, vybrid, ls1021a, omap, qualcomm,
mvebu, allwinner, broadcom, exynos, zynq
- Continued fixes for W=1 dtc warnings
- The old STiH415/416 SoC support gets removed, these never made it into
products and have served their purpose in the kernel as a template
for teh newer chips from ST
- The exynos4415 dtsi file is removed as nothing uses it.
- Intel PXA25x can now be booted using devicetree
Conflicts:
arch/arm/boot/dts/r8a*.dtsi: a node was added
the clk tree, keep both sides and watch out for git
dropping the required '};' at the end of each side.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wJt3
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"Lots of changes as usual, so I'm trying to be brief here. Most of the
new hardware support has the respective driver changes merged through
other trees or has had it available for a while, so this is where
things come together.
We get a DT descriptions for a couple of new SoCs, all of them
variants of other chips we already support, and usually coming with a
new evaluation board:
- Oxford semiconductor (now Broadcom) OX820 SoC for NAS devices
- Qualcomm MDM9615 LTE baseband
- NXP imx6ull, the latest and smallest i.MX6 application processor variant
- Renesas RZ/G (r8a7743 and r8a7745) application processors
- Rockchip PX3, a variant of the rk3188 chip used in Android tablets
- Rockchip rk1108 single-core application processor
- ST stm32f746 Cortex-M7 based microcontroller
- TI DRA71x automotive processors
These are commercially available consumer platforms we now support:
- Motorola Droid 4 (xt894) mobile phone
- Rikomagic MK808 Android TV stick based on Rockchips rx3066
- Cloud Engines PogoPlug v3 based on OX820
- Various Broadcom based wireless devices:
- Netgear R8500 router
- Tenda AC9 router
- TP-LINK Archer C9 V1
- Luxul XAP-1510 Access point
- Turris Omnia open hardware router based on Armada 385
And a couple of new boards targeted at developers, makers or
industrial integration:
- Macnica Sodia development platform for Altera socfpga (Cyclone V)
- MicroZed board based on Xilinx Zynq FPGA platforms
- TOPEET itop/elite based on exynos4412
- WP8548 MangOH Open Hardware platform for IOT, based on Qualcomm MDM9615
- NextThing CHIP Pro gadget
- NanoPi M1 development board
- AM571x-IDK industrial board based on TI AM5718
- i.MX6SX UDOO Neo
- Boundary Devices Nitrogen6_SOM2 (i.MX6)
- Engicam i.CoreM6
- Grinn i.MX6UL liteSOM/liteBoard
- Toradex Colibri iMX6 module
Other changes:
- added peripherals on renesas, davinci, stm32f429, uniphier, sti,
mediatek, integrator, at91, imx, vybrid, ls1021a, omap, qualcomm,
mvebu, allwinner, broadcom, exynos, zynq
- Continued fixes for W=1 dtc warnings
- The old STiH415/416 SoC support gets removed, these never made it
into products and have served their purpose in the kernel as a
template for teh newer chips from ST
- The exynos4415 dtsi file is removed as nothing uses it.
- Intel PXA25x can now be booted using devicetree"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (422 commits)
arm: dts: zynq: Add MicroZed board support
ARM: dts: da850: enable high speed for mmc
ARM: dts: da850: Add node for pullup/pulldown pinconf
ARM: dts: da850: enable memctrl and mstpri nodes per board
ARM: dts: da850-lcdk: Add ethernet0 alias to DT
ARM: dts: artpec: add pcie support
ARM: dts: add support for Turris Omnia
devicetree: Add vendor prefix for CZ.NIC
ARM: dts: berlin2q-marvell-dmp: fix typo in chosen node
ARM: dts: berlin2q-marvell-dmp: fix regulators' name
ARM: dts: Add xo to sdhc clock node on qcom platforms
ARM: dts: r8a7794: Add device node for PRR
ARM: dts: r8a7793: Add device node for PRR
ARM: dts: r8a7792: Add device node for PRR
ARM: dts: r8a7791: Add device node for PRR
ARM: dts: r8a7790: Add device node for PRR
ARM: dts: r8a7779: Add device node for PRR
ARM: dts: r8a73a4: Add device node for PRR
ARM: dts: sk-rzg1e: add Ether support
ARM: dts: sk-rzg1e: initial device tree
...
Changes to platform code for 64-bit ARM platforms. We are not adding
any new platforms that require code or Kconfig changes this time, so
it's basically just defconfig changes to enable support for more
drivers used on the existing platforms.
This is mainly interesting for the Raspberry Pi 3, which should
now work much better with the default build.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=B+Lz
-----END PGP SIGNATURE-----
Merge tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC 64-bit updates from Arnd Bergmann:
"Changes to platform code for 64-bit ARM platforms. We are not adding
any new platforms that require code or Kconfig changes this time, so
it's basically just defconfig changes to enable support for more
drivers used on the existing platforms.
This is mainly interesting for the Raspberry Pi 3, which should now
work much better with the default build"
* tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: defconfig: drop GPIO_SYSFS on multiplatforms
arm64: defconfig: Do not lower CONFIG_LOG_BUF_SHIFT
arm64: defconfig: allow rk3399-based boards to boot from mmc and usb
arm64: defconfig: enable RK808 components
arm64: defconfig: enable I2C and DW MMC controller on rockchip platform
arm64: defconfig: Enable Tegra186 SoC
ARM64: configs: Activate Internal PHY for Meson GXL
arm64: qcom: enable GPIOLIB in Kconfig
arm64: configs: enable configs for msm899(2/4) basic support
ARM64: bcm2835: add thermal driver to default config
ARM64: configs: Add Platform MHU in defconfig
MAINTAINERS: Update Broadcom Vulcan maintainer email
arm64: defconfig: enable EEPROM_AT25 config option
arm64: Enable HIBERNATION in defconfig
arm64: defconfig: Enable DRM DU and V4L2 FCP + VSP modules
ARM64: defconfig: Enable MMC related configs
arm64: Add BCM2835 (Raspberry Pi 3) support to the defconfig
As usual, we queue up a few fixes that don't seem urgent enough to go in
through -rc, or that just came a little too late given their size.
The zx fixes make the platform finally boot on real hardware, the
davinci and imx31 get the DT support working better for some of
the machines that are still normally used with classic board files.
One tegra fix is important for new bootloader versions, but the
bug has been around for a while without anyone noticing.
The other changes are mostly cosmetic.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=i2l2
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-urgent fixes from Arnd Bergmann:
"As usual, we queue up a few fixes that don't seem urgent enough to go
in through -rc, or that just came a little too late given their size.
The zx fixes make the platform finally boot on real hardware, the
davinci and imx31 get the DT support working better for some of the
machines that are still normally used with classic board files. One
tegra fix is important for new bootloader versions, but the bug has
been around for a while without anyone noticing.
The other changes are mostly cosmetic"
* tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (22 commits)
arm64: tegra: Add missing Smaug revision
arm64: tegra: Add VDD_GPU regulator to Jetson TX1
arm64: dts: zte: clean up gic-v3 redistributor properties
arm64: dts: zx: Fix gic GICR property
bus: vexpress-config: fix device reference leak
soc: ti: qmss: fix the case when !SMP
ARM: lpc32xx: drop duplicate header device.h
ARM: ixp4xx: drop duplicate header gpio.h
ARM: socfpga: fix spelling mistake in error message
ARM: dts: imx6q-cm-fx6: fix fec pinctrl
ARM: dts: imx7d-pinfunc: fix UART pinmux defines
ARM: dts: imx6qp: correct LDB clock inputs
ARM: OMAP2+: pm-debug: Use seq_putc() in two functions
ARM: OMAP2+: Remove the omapdss_early_init_of() function
mfd: tps65217: Fix mismatched interrupt number
ARM: zx: Fix error handling
ARM: spear: Fix error handling
ARM: davinci: da850: Fix pwm name matching
ARM: clk: imx31: properly init clocks for machines with DT
clk: imx31: fix rewritten input argument of mx31_clocks_init()
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ut0k
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"PCI changes:
- add support for PCI on ARM64 boxes with ACPI. We already had this
for theoretical spec-compliant hardware; now we're adding quirks
for the actual hardware (Cavium, HiSilicon, Qualcomm, X-Gene)
- add runtime PM support for hotplug ports
- enable runtime suspend for Intel UHCI that uses platform-specific
wakeup signaling
- add yet another host bridge registration interface. We hope this is
extensible enough to subsume the others
- expose device revision in sysfs for DRM
- to avoid device conflicts, make sure any VF BAR updates are done
before enabling the VF
- avoid unnecessary link retrains for ASPM
- allow INTx masking on Mellanox devices that support it
- allow access to non-standard VPD for Chelsio devices
- update Broadcom iProc support for PAXB v2, PAXC v2, inbound DMA,
etc
- update Rockchip support for max-link-speed
- add NVIDIA Tegra210 support
- add Layerscape LS1046a support
- update R-Car compatibility strings
- add Qualcomm MSM8996 support
- remove some uninformative bootup messages"
* tag 'pci-v4.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (115 commits)
PCI: Enable access to non-standard VPD for Chelsio devices (cxgb3)
PCI: Expand "VPD access disabled" quirk message
PCI: pciehp: Remove loading message
PCI: hotplug: Remove hotplug core message
PCI: Remove service driver load/unload messages
PCI/AER: Log AER IRQ when claiming Root Port
PCI/AER: Log errors with PCI device, not PCIe service device
PCI/AER: Remove unused version macros
PCI/PME: Log PME IRQ when claiming Root Port
PCI/PME: Drop unused support for PMEs from Root Complex Event Collectors
PCI: Move config space size macros to pci_regs.h
x86/platform/intel-mid: Constify mid_pci_platform_pm
PCI/ASPM: Don't retrain link if ASPM not possible
PCI: iproc: Skip check for legacy IRQ on PAXC buses
PCI: pciehp: Leave power indicator on when enabling already-enabled slot
PCI: pciehp: Prioritize data-link event over presence detect
PCI: rcar: Add gen3 fallback compatibility string for pcie-rcar
PCI: rcar: Use gen2 fallback compatibility last
PCI: rcar-gen2: Use gen2 fallback compatibility last
PCI: rockchip: Move the deassert of pm/aclk/pclk after phy_init()
..
Geert Uytterhoeven
Wolfram Sang
Marek Szyprowski
Robin Murphy
Kefeng Wang
Ard Biesheuvel
Chen-Yu Tsai
Chen Feng
Christoffer Dall
Thierry Reding
Andrzej Hajda
Bart Van Assche
Kevin Hilman
Neil Armstrong
Will Deacon
dawei.chien@mediatek.com
Masahiro Yamada
Pankaj Dubey
Linus Torvalds
Zhou Wang
Russell King
Jaechul Lee
Mitchel Humpherys
Mark Rutland
Olof Johansson
Andreas Färber
Martin Blumenstingl
Dave Martin
Javier Martinez Canillas
Oleksandr Andrushchenko
Mike Leach
Sudeep Holla
Radim Krčmář
Alexander Graf
Srinivas Kandagatla
Ivan T. Ivanov
Bjorn Andersson
spjoshi@codeaurora.org
Georgi Djakov
Xing Zheng
Daniel Kurtz
Bibby Hsieh
Robert Richter
Miles Chen
Jintack Lim
Shawn Lin
Suzuki K Poulose
Takeshi Kihara
Laura Abbott
Huang Shijie
James Morse
Joel Fernandes
Kuninori Morimoto
Jia Hongtao
Harninder Rai
Andi Shyti
Chanwoo Choi
Krzysztof Kozlowski
Icenowy Zheng
Arnd Bergmann
Laurent Pinchart
Jon Mason
Thomas Petazzoni
Alexandre Belloni
Romain Perier
Simon Horman
Chris Paterson
Baoyou Xie
Meng Yi
Andy Yan
William wu
Brian Norris
Moritz Fischer
Michal Simek
Stephen Boyd
Al Viro
Thomas Gleixner
Rafael J. Wysocki
Lv Zheng
Alexander Popov