As we are restoring power to a known card, it makes sense to use
the 'ocr' value known for the card rather than the generic one
for the host interface.
This matches the use of card->ocr passed to mmc_power_up in
mmc_sdio_runtime_resume (just before mmc_sdio_power_restore is
called), and the value passed to mmc_sdio_init_card() a little
later in mmc_sdio_power_restore().
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch resurrects an old never-finished driver for Toshiba PCI SD
controllers found in some older Toshiba laptops (such as Portege R100):
02:0d.0 System peripheral [0880]: Toshiba America Info Systems SD TypA Controller [1179:0805] (rev 05)
The code is fixed, cleaned up and successfully tested with SD, SDHC, SDXC and
MMC cards on Portege R100. (MMC cards don't even work in Windows!)
SDIO probably does not work (don't have any SDIO card).
The hardware is slow (around 2 MB/s - same in Windows) because it does not
support bus mastering (busmaster enable bit cannot be set in PCI control reg).
Also the card clock is limited to 16MHz (33MHz PCI clock divided by 2).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Exynos7 has a DWMMC controller (v2.70a) which is different from
prior versions. This patch adds new compatible strings for exynos7.
This patch also fixes the CLKSEL register offset on exynos7.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Tested-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_do_hw_reset(), mmc_power_up() and mmc_power_off() all set similar
initial values for bus_mode, bus_width, chip_select and timing. Let's
make this handling simpler and more consistent by sticking them
together in a common function. This will introduce small changes in
behavior in the following places:
mmc_power_off():
For SPI hosts, explicitly set bus_mode = MMC_BUSMODE_PUSHPULL and
chip_select = MMC_CS_HIGH, before we left them as they were.
For non-SPI hosts, set bus_mode = MMC_BUSMODE_PUSHPULL instead of
MMC_BUSMODE_OPENDRAIN as before.
These two changes should not be a problem since the device will be
powered off anyway.
mmc_do_hw_reset():
Always set bus_mode = MMC_BUSMODE_PUSHPULL, as required by SD/SDIO
cards. MMC cards require MMC_BUSMODE_OPENDRAIN, but this is taken
care of by mmc_init_card() and mmc_attach_mmc().
Signed-off-by: Johan Rudholm <johanru@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
omap_hsmmc only supports one slot. So slot id is always zero, and
slot id was never used in the callbacks anyway
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
These callbacks are set during driver probe and not from the platform
init, -- evtl. they had been for oamp 1/2 -- for omap3 they are local
functions of the driver. These indirection could be dropped
altogether in favor of regular function calls TODO
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
this is needed when installing callbacks in the host struct and not
in the platform data, e.g. cover detect irq should be stored in
omap_hsmmc_host and not platform data
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
omap_hsmmc supports only one slot per controller, see OMAP_MMC_MAX_SLOTS.
This unnecessary indirection leads to confusion in the omap_hsmmc driver.
For example the card_detect callback is not installed by platform code
but from the driver probe function. So it should be a field of
omap_hsmmc_host. But since it is declared under the platform slot while
the drivers struct omap_hsmmc_host has no slot abstraction, this looks
like a bug, especially when not familiar that this driver only supports
1 slot anyway.
Either we should add a slot abstraction to omap_hsmmc_host or remove
it from the platform data struct. Removed since slot multiplexing is
an un-implemented feature
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
these callbacks are not set, probably legacy omap 1/2 features
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- omap mmc driver supports multiplexing, omap_mmc_hs doesn't
this leads to one of the major confusions in the omap_hsmmc driver
- platform data should be read-only for the driver
most callbacks are not set by the omap3 platform init code while still
required. So they are set from the driver probe function, which is against
the paradigm that platform-data should not be modified by the driver
typical examples are card_detect, read_only callbacks
un-bundling by searching for driver name \"omap_hsmmc in the
arch/arm folder. omap_hsmmc_platform_data is not initialized directly,
but from omap2_hsmmc_info, which is defined in a separate header file
not touched by this patch
hwmod includes platform headers to declare features of the platform. All
the declared features are prefixed OMAP_HSMMC. There is no need to
include platform header from hwmod other except for feature defines
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Amend the atmel mci pin controller to optionally take a pin control
handle and set the state of the pins to:
- "default" on boot, resume and before performing an transfer.
- "sleep" on suspend().
This should make it possible to optimize energy usage for the pins
both for the suspend/resume cycle.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MMC core already has support for HS400. Add HS400
support to SDHCI driver. The SDHC Standard specification
does not define HS400 so consequently HS400 support is
non-standard. However HS400 is not selected without
the host controller setting the corresponding capability
flags so host controllers not yet supporting HS400
will not be affected. To support that, a quirk
SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400 is introduced to
enable the use of capabilities register reserved bit-63
to indicate HS400 support.
Because HS400 is non-standard for SDHCI, it is possible
that different vendors will do things in different ways.
However HS200 support faced the same issue but currently
there is only one solution. As such, no attempt has
been made to provide for alternate HS400 solutions except
for SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
1.2V HS200 mode capability is cleared if there is not a voltage
regulator that supports 1.2V. Do the same for 1.2V HS400 mode.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
supply.vqmmc is used with the IS_ERR macro which means
the value must be valid or an error code. NULL is
neither, so replace with ERR_PTR(-EINVAL).
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Synopsys DW_MMC IP core supports Internal DMA Controller with 64-bit address mode from IP version 2.70a onwards.
Updated the driver to support IDMAC 64-bit addressing mode.
Signed-off-by: Prabu Thangamuthu <prabu.t@synopsys.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
AMD SD controller supports the SDR104 mode, but caps2 can not
be promoted to support hs200 for eMMC.
Signed-off-by: Vincent Wan <vincent.wan@amd.com>
Signed-off-by: Wan Zongshun <mcuos.com@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch is to enable the quirk for AMD sdhci requiring transfer
mode register need to be cleared for commands without data
Signed-off-by: Vincent Wan <vincent.wan@amd.com>
Signed-off-by: Wan Zongshun <mcuos.com@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHC controller in AMD chipsets require SDHC transfer mode
register to be cleared for commands without data. The issue was
uncovered during testing eMMC cards on KB/ML based platforms
Signed-off-by: Vincent Wan <vincent.wan@amd.com>
Signed-off-by: Wan Zongshun <mcuos.com@gmail.com>
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Tested-by: Vikram B <vikram.b@amd.com>
Tested-by: Raghavendra Swamy <raghavendra.swamy@amd.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is possible that we may fail to set the clock rate, if we do so then
log the failure and don't bother reprogramming the IP.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The "Badly aligned" tests, test reading/writing with alignments
of 1,2 and 3. SDHCI now has 64-bit ADMA which has 8-byte
alignment, so extend the tests to test up to 7.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Set a 64-bit DMA mask when using 64-bit DMA.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Set the DMA mask during the first call to ->enable_dma() to
make use of the SDHCI_USE_64_BIT_DMA flag.
This patch is dependent on
commit 8a2f38ddfe ("ACPI / platform: provide default DMA mask")
which provides the dev->dma_mask pointer without
which dma_set_mask_and_coherent() will always fail.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add 64-bit ADMA support including:
- add 64-bit ADMA descriptor
- add SDHCI_USE_64_BIT_DMA flag
- set upper 32-bits of DMA addresses
- ability to select 64-bit ADMA
- ability to use 64-bit ADMA sizes and alignment
- display "ADMA 64-bit" when host is added
It is assumed that a 64-bit capable device has set a 64-bit DMA mask
and *must* do 64-bit DMA. A driver has the opportunity to change
that during the first call to ->enable_dma(). Similarly
SDHCI_QUIRK2_BROKEN_64_BIT_DMA must be left to the drivers to
implement.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Define the ADMA descriptor structure instead of
using manual offsets and casts.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Define all the ADMA constants instead of having numbers
scattered throughout the code.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Define the maximum number of segments instead of
having the constant 128 appearing in the code in
various places.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for 64-bit ADMA, parameterize ADMA sizes
and alignment. 64-bit ADMA has a larger descriptor
because it contains a 64-bit address instead of a 32-bit
address. Also data must be 8-byte aligned instead
of 4-byte aligned. Consequently, sdhci_host members
are added for descriptor, table, and buffer sizes
and alignment.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is kernel-style to use 'void *' for anonymous data.
This is being applied to the ADMA bounce buffer which
contains unaligned bytes, and to the ADMA descriptor
table which will contain 32-bit ADMA descriptors
or 64-bit ADMA descriptors when support is added.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for 64-bit ADMA, separate out code
that touches the ADMA descriptor by adding
sdhci_adma_mark_end().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for 64-bit ADMA, rename adma_desc to
adma_table. That is because members will be added
for descriptor size and table size, so using adma_desc
(which is the table) is confusing.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Rename sdhci_set_adma_desc to sdhci_adma_write_desc and
sdhci_show_adma_error to sdhci_adma_show_error so that
all ADMA functions start with sdhci_adma_.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The intent of the warning is to warn if the ADMA table
overflows. However there can be one more 'end' entry
so the condition should be adjusted accordingly.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Bytes are being copied from/to a single page. The intent
of the warning is to warn if the page boundary is crossed.
There are two problems. First, PAGE_MASK is mistaken for
(PAGE_SIZE - 1). Secondly, instead of using the number
of bytes to copy, the warning is using the maximum that
that value could be. Fix both.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The ADMA2 descriptor table size was being calculated incorrectly
Fix it.
Note that it has been wrong for a long time and likely has not
caused any problems because of a combination of 1) not needing
alignment descriptors for block operations 2) more memory being
allocated than was requested 3) the use of
SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC which does not use an extra
descriptor for the end marker.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for non-removable slots which have no card detection GPIO
and which should not be polled for a card change.
Signed-off-by: Timo Kokkonen <timo.kokkonen@offcode.fi>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Besides the I/O clock, some PXAv3 SDHCI IP also requires a core clock to
be enabled. Add an optional core clock to the corresponding driver.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
With support for more than one clock, we'll need to distinguish between
the clock by name. Change clock probing to first try to get "io" clock
before falling back to unnamed clock.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As we are using references to the I/O clock throughout the driver,
move it to the private data. Also, in preparation for core clock,
rename it to clk_io.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_add_host and sdhci_platfm_init already report failure,
so don't emit error messages when a failure occurs. This prevents
occurences of "deferred" messages when required power supplies
are not ready for operation yet.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Due to previous patches, all callers of mmc_send_cxd_data() now
allocates their buffers from the heap. This enables us to simplify
mmc_send_cxd_data() by removing the support of handling buffers, which
are allocated from the stack.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Previous patches has replaced the calls to mmc_send_ext_csd() into
mmc_get_ext_csd(), thus mmc_send_ext_csd() has become redundant. Let's
remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Callers of mmc_send_ext_csd() will be able to decrease code duplication
by using mmc_get_ext_csd() instead. Let's make it available.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The callers of mmc_get_ext_csd() need the flexibility to handle errors
themselves, because they behave differently.
Let's clean up mmc_get_ext_csd() with its friends and adopt the error
handling as stated above.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As a step in cleaning up code around reading/decoding EXT_CSD, convert
the current mmc_read_ext_csd(), to handle both fetching the EXT_CSD
and decoding its data.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The helper function mmc_can_ext_csd() will return a positive value if
the card supports the EXT_CSD register. Start using it at relavant
places in the mmc core.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the MMC spec version is < CSD_SPEC_VER_4, there aren't support for
the EXT_CSD register. Since max_dtr is fetched from there, it will
default to zero, which thus isn't needed to verify.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The validation of the buswidth and the MMC spec version in
__mmc_select_powerclass() is redundant, let's remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_send_ext_csd() is an exported function used by both the mmc core
and the mmc block layer. Let's remove the local duplicated definition
in the mmc core.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The dw_mmc driver had a bunch of code that ran whenever a card was
ejected and inserted. However, this code was old and crufty and
should be removed. Some evidence that it's really not needed:
1. Is is supposed to be legal to use 'cd-gpio' on dw_mmc instead of
using the built-in card detect mechanism. The 'cd-gpio' code
doesn't run any of the crufty old code but yet still works.
2. While looking at this, I realized that my old change (369ac86 mmc:
dw_mmc: don't queue up a card detect at slot startup) actually
castrated the old code a little bit already and nobody noticed.
Specifically "last_detect_state" was left as 0 at bootup. That
means that on the first card removal none of the crufty code ran.
3. I can run "while true; do dd if=/dev/mmcblk1 of=/dev/null; done"
while ejecting and inserting an SD Card and the world doesn't
explode.
If some of the crufty old code is actually needed, we should justify
it and also put it in some place where it will be run even with
"cd-gpio".
Note that in my case I'm using the "cd-gpio" mechanism but for various
reasons the hardware triggers a dw_mmc "card detect" at bootup. That
was actually causing a real bug. The card detect workqueue was
running while the system was trying to enumerate the card. The
"present != slot->last_detect_state" triggered and we were doing all
kinds of crazy stuff and messing up enumeration. The new mechanism of
just asking the core to check the card is much safer and then the
bogus interrupt doesn't hurt.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: alim.akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Presumably ->slotno is normally fairly small and the shift doesn't wrap
but static checkers will complain about it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
"ret" is a signed int, so use "%d" in format strings instead of "%u".
This prevents cryptic codes in error messages like this:
sdhci-arasan e0101000.sdhci: platform register failed (4294966779)
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move the mach header that can come either from arm/mach-at91 or avr32 to
platform_data to be able to switch the AT91 platforms to multiplatform.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[Ulf: Fixed compile error]
For eMMC 5.0 compliant device, firmware version is stored in ext_csd.
Report firmware as a 64bit hexa decimal. Vendor can use hexa or ascii
string to report firmware version.
Also add FFU related EXT_CSD register and note if the device is FFU capable.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The "set_ios" function is called with a clock of 0 when the clock is
turning off. There's no reason to go through all the extra Rockchip
logic (whose goal is to make sure DIV is 0 or 1) in that case. The
Rockchip logic happened to work because the CCF will pick the lowest
possible rate when you ask it for a clock of 0, but it's silly to go
through all the remuxing and adjusting for no reason.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In (28f92b5 mmc: core: Try other signal levels during power up) we can
see that there are times when it's valid to try several signal
voltages. Don't print an ugly error in the logs when that happens.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We've already got a reset of DMA after it's done. Add one before we
start DMA too. This fixes a data corruption on Rockchip SoCs which
will get bad data when doing a DMA transfer after doing a PIO transfer.
We tested this on an Exynos 5800 with HS200 and didn't notice any
difference in sequential read throughput.
Signed-off-by: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In most of the cases mmc_get|set_drvdata() didn't simplify code, which
should be the primary reason for such macros.
Let's remove them and convert to the common device_driver macros,
dev_set|get_drvdata() instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The msm_sdcc host shall not use mmc core specific macros to handle its
driver data. Instead, convert to use the platform device driver macros.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The struct mmc_driver adds an extra layer on top of the struct
device_driver. That would be fine, if there were a good reason, but
that's not the case.
Let's simplify code by converting to the common struct device_driver
instead and thus also removing superfluous overhead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of having specific mmc system PM callbacks for the mmc driver,
let's convert to use the common ones.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
NULL-checking a struct clk it not only wrong but also not required as
for PXAv3 driver the corresponding clock is mandatory. Remove the
checks from sdhci_pxav3_runtime_{suspend,resume}.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
clk_enable from struct sdhci_pxa is unused, remove it from the private
driver data.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
struct sdhci_pxa is only used in sdhci_pxa driver itself, so move it
there.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit bb8175a8aa
("mmc: sdhci: clarify DDR timing mode between SD-UHS and eMMC")
added MMC_DDR52 as eMMC's DDR mode to be distinguished from SD-UHS.
While the differentation may be useful, pxav3 SDHCI controller lacks
a corresponding check in its custom .set_uhs_signaling callback for
MMC_DDR52. This patch adds a new switch case for MMC_TIMING_MMC_DDR52
to MMC_TIMING_UHS_DDR50 case.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
struct sdhci_pxa is private data of PXA SDHCI driver, but not used in
sdhci-pxav2 at all. Drop unused references to struct sdhci_pxa.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
While starting the bkops the previously prepared request should be canceled
and restarted after the bkops. As the prepared resource might already
setup the dma channels and ready to be started. Now with the arrival of bkops
request this prepared request can be serviced ONLY after the bkops. So
holding on to the prepared request in the host driver is confusing at
this point in time, so it makes sense to cleanup such dangling requests and
reissue this request once bkops is done.
Canceling the prepared request would give opportunity to the host drivers
to perform cleanup on the prepared request.
Without this patch host drivers like mmci gets confused when a blocking
request like send_ext_csd(CMD8) is issued while there is already a prepared
request. With the help of this patch, the driver can better manage such
blocking requests and cleanup the prepared requests which are not started yet.
Without this patch I hit below crash on Qualcomm APQ8064 based IFC6410 board
with mmci host driver.
mmci-pl18x 12400000.sdcc: error during DMA transfer!
Unable to handle kernel paging request at virtual address 40000000
pgd = c0204000
[40000000] *pgd=00000000
Internal error: Oops: 805 [#1] SMP ARM
Modules linked in: ipv6 ath6kl_sdio ath6kl_core
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 3.17.0-rc7-linaro-multi-v7 #1
task: c0c9d7e0 ti: c0c92000 task.ti: c0c92000
PC is at v7_dma_inv_range+0x34/0x4c
LR is at __dma_page_dev_to_cpu+0x80/0x100
pc : [<c021efc0>] lr : [<c021af18>] psr: 400f0193
sp : c0c93e20 ip : c0c9a478 fp : c08ea538
r10: c0c9f548 r9 : 00000002 r8 : e97d9000
r7 : 00000200 r6 : c0c9d504 r5 : c0db0880 r4 : 00000000
r3 : 0000003f r2 : 00000040 r1 : 40000200 r0 : 40000000
Flags: nZcv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c5787d Table: a9ef406a DAC: 00000015
Process swapper/0 (pid: 0, stack limit = 0xc0c92250)
Stack: (0xc0c93e20 to 0xc0c94000)
3e20: c021f058 e9a17178 e9a171bc e99dfd6c 00000001 00000001 e995de10 00000002
3e40: 00000000 c021b574 00000000 c04bc4a4 00000000 e9b49ac0 c0ce6e6c e99dfda4
3e60: 00000088 e9810780 c0d8291c c072ea58 00000000 c072d3fc 00000000 c072f534
3e80: 00000000 e9b49ac0 00000100 c0c9a444 00000088 c072f6b4 c072f5d4 e9d40080
3ea0: e98107dc 00000000 00000000 c0280a60 00000000 7d55bf61 e9810780 e98107dc
3ec0: 00000000 f0002000 c0d460e8 c0d460e8 c0c92000 c0280b60 e9810780 c0ce7190
3ee0: 00000000 c028369c c02835f4 00000088 00000088 c0280278 c0c8ec70 c020f080
3f00: f000200c c0c9a958 c0c93f28 c02088e4 c04bd630 c04bd5bc 200f0013 ffffffff
3f20: c0c93f5c c0212800 00000001 a987c000 c0c93f3c c04bd574 00000000 0000015b
3f40: ea7a0e40 00000000 c0d460e8 c0d460e8 c0c92000 c08ea538 29b12000 c0c93f70
3f60: c04bd630 c04bd5bc 200f0013 ffffffff c04bd574 c071bd24 7d50c9b4 c0719a44
3f80: 7d50c9b4 0000015b c0c9a498 c0c92028 c0c9a498 c0c9a4fc ea7a0e40 c0c8ee38
3fa0: c0d460e8 c0276198 00000000 c0d8291a 00000000 c0c9a400 00000000 c0be0bc4
3fc0: ffffffff ffffffff c0be05f8 00000000 00000000 c0c533d8 c0d82ed4 c0c9a47c
3fe0: c0c533d4 c0c9e870 8020406a 511f06f0 00000000 80208074 00000000 00000000
[<c021efc0>] (v7_dma_inv_range) from [<c021af18>] (__dma_page_dev_to_cpu+0x80/0x100)
[<c021af18>] (__dma_page_dev_to_cpu) from [<c021b574>] (arm_dma_unmap_sg+0x5c/0x84)
[<c021b574>] (arm_dma_unmap_sg) from [<c072ea58>] (mmci_dma_unmap.isra.16+0x60/0x74)
[<c072ea58>] (mmci_dma_unmap.isra.16) from [<c072f534>] (mmci_data_irq+0x1fc/0x29c)
[<c072f534>] (mmci_data_irq) from [<c072f6b4>] (mmci_irq+0xe0/0x114)
[<c072f6b4>] (mmci_irq) from [<c0280a60>] (handle_irq_event_percpu+0x78/0x134)
[<c0280a60>] (handle_irq_event_percpu) from [<c0280b60>] (handle_irq_event+0x44/0x64)
[<c0280b60>] (handle_irq_event) from [<c028369c>] (handle_fasteoi_irq+0xa8/0x1a8)
[<c028369c>] (handle_fasteoi_irq) from [<c0280278>] (generic_handle_irq+0x2c/0x3c)
[<c0280278>] (generic_handle_irq) from [<c020f080>] (handle_IRQ+0x40/0x90)
[<c020f080>] (handle_IRQ) from [<c02088e4>] (gic_handle_irq+0x38/0x68)
[<c02088e4>] (gic_handle_irq) from [<c0212800>] (__irq_svc+0x40/0x54)
Exception stack(0xc0c93f28 to 0xc0c93f70)
3f20: 00000001 a987c000 c0c93f3c c04bd574 00000000 0000015b
3f40: ea7a0e40 00000000 c0d460e8 c0d460e8 c0c92000 c08ea538 29b12000 c0c93f70
3f60: c04bd630 c04bd5bc 200f0013 ffffffff
[<c0212800>] (__irq_svc) from [<c04bd5bc>] (msm_cpu_pm_enter_sleep+0x48/0x4c)
[<c04bd5bc>] (msm_cpu_pm_enter_sleep) from [<c071bd24>] (qcom_lpm_enter_spc+0x20/0x2c)
[<c071bd24>] (qcom_lpm_enter_spc) from [<c0719a44>] (cpuidle_enter_state+0x44/0xf0)
[<c0719a44>] (cpuidle_enter_state) from [<c0276198>] (cpu_startup_entry+0x1f4/0x238)
[<c0276198>] (cpu_startup_entry) from [<c0be0bc4>] (start_kernel+0x384/0x390)
Code: 1e070f3e e1110003 e1c11003 1e071f3e (ee070f36)
---[ end trace cf6cb3f6432c9834 ]---
Kernel panic - not syncing: Fatal exception in interrupt
Reported-by: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In mmc_init_card function some of the branches in error handling paths
go to "err" label, which skips removing of newly allocated card structure,
that will actually not be used. Fix that by using proper "free_card" label.
Also, some messages in these branches are reported as warnings,
although the operation processing is not continued. Change these
messages to error level.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The debug messages with commands execution results, that are printed
after processing the request, do not include results of sbc (set block count)
part of request. Add the debug message for that part too.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some request fields are initialized just before request processing
for sanity purposes. This is done for command, data, and stop parts
of the request, but not for sbc (set block count) part. Add such
initialization for that part too.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add the case of SET_BLOCK_COUNT command error to the error conditions
check for making a controller reset at request handling finish.
Otherwise, if the SET_BLOCK_COUNT command failed, e.g. with a timeout,
the controller state was not reset, and the next command failed too.
In the case of data error the controller reset is already done in
finish_data() function before sending stop command (if present),
so the finish tasklet should make a reset after data error only
if no stop command existed in the request.
Also, fix the indentation of this condition check to make it more logical.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As a follow-up of commit
"mmc: sdhci: Balance vmmc regulator_enable(), and always enable vqmmc"
vmmc regulator disable is also not needed in sdhci_remove_host.
The regulator is completely controlled by mmc_power_up and mmc_power_off
functions and is already disabled by the time of removing the host.
Extra regulator_disable call in sdhci_remove_host is unbalanced and
causes a warning reported by regulator core, so should be removed.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit ad93220de7 ("mmc: sdhci-esdhc-imx: change pinctrl state
according to uhs mode") exits the probe in case there are no valid
pinctrl states found.
As there are configurations doing the pin mux properly in the boot
loader, don't exit. Just warn, but go on in case if there are no
pinctrl states in the device tree.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If available voltages are not given, mmc_regulator_get_supply() function
returns 0 and mxcmmc driver doesn't set a value for ocr_avail mask.
In accordance with the comment in platform_data/mmc-mxcmmc.h,
fix it, assuming MMC_VDD_32_33 | MMC_VDD_33_34 as default value.
Signed-off-by: Matteo Facchinetti <matteo.facchinetti@sirius-es.it>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
During a read of data block using dma, driver might have two ways to finish to read
and free the resources:
1) checking STATUS_DATA_TRANS_DONE mask, in the mxcmci_irq() routine
(pending to mmc irq)
2) mxmmc driver, registers also a mxcmci_dma_callback() and when transfer is finished,
dma driver calls this callback. (pending to dma irq)
Both ways are concurrent with each other.
Race condition happens when following events occur:
/* (1) mxcmci driver start data transfer */
158.418970: mpc_dma_execute: mpc_dma_execute(): will_access_peripheral start cid=31
158.418976: mpc_dma_issue_pending <-mxcmci_request
158.418983: mxcmci_start_cmd <-mxcmci_request
/* (2) mxcmci driver receive mmc irq */
158.419656: mxcmci_irq <-handle_irq_event_percpu
158.419692: mxcmci_read_response <-mxcmci_irq
/* (3) mxcmci driver checks that transfer is complete and call mxcmci_finish_data() */
158.419726: mxcmci_data_done <-mxcmci_irq
158.419729: mxcmci_finish_data <-mxcmci_data_done
158.419733: dma_direct_unmap_sg <-mxcmci_finish_data
158.419736: mxcmci_swap_buffers.isra.24 <-mxcmci_finish_data
158.419762: mxcmci_read_response <-mxcmci_data_done
/* (4) mxcmci driver (no dma): send stop command */
158.419765: mxcmci_start_cmd <-mxcmci_data_done
/* (5) mxcmci driver (no dma): receive the stop command irq response */
158.419782: mxcmci_irq <-handle_irq_event_percpu
158.419812: mxcmci_read_response <-mxcmci_irq
158.419843: mxcmci_finish_request <-mxcmci_irq
/* (6) dma driver: receive dma irq (finish data transfer) related by request on step 1 */
158.419853: mpc_dma_irq <-handle_irq_event_percpu
158.420001: mpc_dma_irq_process <-mpc_dma_irq
158.420004: mpc_dma_irq_process <-mpc_dma_irq
/* (7) dma driver: start dma tasklet to finish the dma irq handling */
158.420008: mpc_dma_irq_process: mpc_dma_irq_process(): completed ch:31
/* (8) mxcmci driver: start next data transfer using dma */
158.420174: mxcmci_request <-mmc_start_req
158.420182: dma_direct_map_sg <-mxcmci_request
158.420192: mpc_dma_prep_slave_sg <-mxcmci_request
/* (9) dma driver: schedule irq tasklet and execute mxcmci dma driver callback */
158.420250: mpc_dma_tasklet <-tasklet_action
158.420254: mpc_dma_process_completed <-tasklet_action
158.420267: mxcmci_dma_callback <-mpc_dma_process_completed
/* ERROR!!! (10) mxcmci driver callback works on dma data related to the step 1
that is already finished */
158.420271: mxcmci_data_done <-mpc_dma_process_completed
158.420273: mxcmci_finish_data <-mxcmci_data_done
/* ERROR!!! (11) mxcmci driver: clear data that should be used by step 8 and
send an other mmc stop command (already sended on step 4) */
158.420276: dma_direct_unmap_sg <-mxcmci_finish_data
158.420279: mxcmci_swap_buffers.isra.24 <-mxcmci_finish_data
158.420330: mxcmci_read_response <-mxcmci_data_done
158.420333: mxcmci_start_cmd <-mxcmci_data_done
158.420338: dma_run_dependencies <-mpc_dma_process_completed
...
...
...
168.474223: mxcmci_watchdog <-call_timer_fn
168.474236: mxcmci_watchdog: mxcmci_watchdog
168.474397: mpc_dma_device_control <-mxcmci_watchdog
In accordance with the other drivers that using the dma engine,
fix it, leaving *only* to dma driver the complete control to
ending the read operation.
Removing STATUS_READ_OP_DONE event activation, has as effect
to force mxcmci driver to handle the finish data transfer only
by mxcmci dma callback.
Signed-off-by: Matteo Facchinetti <matteo.facchinetti@sirius-es.it>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since commit 89168b4899 ("mmc: core: restore detect line inversion
semantics"), the SD card on i.MX28 (and possibly other) devices isn't
detected and booting stops at:
[ 4.120617] Waiting for root device /dev/mmcblk0p3...
This is caused by the MMC_CAP2_CD_ACTIVE_HIGH flag being set incorrectly
when the host controller doesn't use a GPIO for card detection (but
instead uses a dedicated pin). In this case mmc_gpiod_request_cd() will
return before assigning to the gpio_invert variable, leaving the
variable uninitialized. The variable then gets used to set the flag.
This patch fixes the issue by making sure gpio_invert is set to false
when a GPIO isn't used. After this patch, i.MX28 boots fine.
The MMC_CAP2_RO_ACTIVE_HIGH (write protect) flag is also set incorrectly
for the exact same reason (it uses the same uninitialized variable), so
this patch fixes that too.
Fixes: 89168b4899 ("mmc: core: restore detect line inversion semantics")
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Kristina Martšenko <kristina.martsenko@gmail.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull block layer driver update from Jens Axboe:
"This is the block driver pull request for 3.18. Not a lot in there
this round, and nothing earth shattering.
- A round of drbd fixes from the linbit team, and an improvement in
asender performance.
- Removal of deprecated (and unused) IRQF_DISABLED flag in rsxx and
hd from Michael Opdenacker.
- Disable entropy collection from flash devices by default, from Mike
Snitzer.
- A small collection of xen blkfront/back fixes from Roger Pau Monné
and Vitaly Kuznetsov"
* 'for-3.18/drivers' of git://git.kernel.dk/linux-block:
block: disable entropy contributions for nonrot devices
xen, blkfront: factor out flush-related checks from do_blkif_request()
xen-blkback: fix leak on grant map error path
xen/blkback: unmap all persistent grants when frontend gets disconnected
rsxx: Remove deprecated IRQF_DISABLED
block: hd: remove deprecated IRQF_DISABLED
drbd: use RB_DECLARE_CALLBACKS() to define augment callbacks
drbd: compute the end before rb_insert_augmented()
drbd: Add missing newline in resync progress display in /proc/drbd
drbd: reduce lock contention in drbd_worker
drbd: Improve asender performance
drbd: Get rid of the WORK_PENDING macro
drbd: Get rid of the __no_warn and __cond_lock macros
drbd: Avoid inconsistent locking warning
drbd: Remove superfluous newline from "resync_extents" debugfs entry.
drbd: Use consistent names for all the bi_end_io callbacks
drbd: Use better variable names
- Fix SDIO IRQ bug.
- MMC regulator improvements.
- Fix slot-gpio card detect bug.
- Add support for Driver Stage Register.
- Convert the common MMC OF parser to use GPIO descriptors.
- Convert MMC_CAP2_NO_MULTI_READ into a callback, ->multi_io_quirk().
- Some additional minor fixes.
MMC host:
- mmci: Support Qualcomm specific DML layer for DMA.
- dw_mmc: Use common MMC regulators.
- dw_mmc: Add support for Rock-chips RK3288.
- tmio: Enable runtime PM support.
- tmio: Add support for R-Car Gen2 SoCs.
- tmio: Several fixes and improvements.
- omap_hsmmc: Removed Balaji from MAINTAINERS.
- jz4740: add DMA and pre/post support.
- sdhci: Add support for Intel Braswell.
- sdhci: Several fixes and improvements.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJUNoFRAAoJEP4mhCVzWIwp+oQP/3a9Rs85+lKwnaDtCotCnvps
LF2R1qiFbeTgQ4XwJvOctuX0VX3/9/XTRhXq+/txA8phlXzqL5BarbXv8WfLILJJ
DgXDt/lTeW1NzJ9WYjrmV/rsH7qlbyIq6I+7kXVT15M86Qqx40DF0hSx/idDKDc4
1ly4trLh0ZeqsM10AR9nu6h/ykVBblHOLSnMZXbBhtmIVshvNg+5KRQkSmwtvTKy
/DswgxmuM1H1Z0T+qNejh4AZSCvxYPlwN06eqYzpYrGuoPH+SafJVws5o1G9z9SX
t/A9i1QDxFtvDP0u1twEAYv0R4e3H24OPit3R8p2tgMUw683576DPYkF2A13Yzxj
c3mYiTAPK8UfRc9kWxCRSkaI38URna1+t7hHRuT/Ha6DBlAvHpRL+wIu+/25XVh+
vNwOmECtT9DzmL2UP+SHLQtyyy3guAFSsFP5RJzuA5wcYeLpNYobcJJCGuziLNYi
PZ55O+2HRtd7my4A7NiXAib+CXTPs4VY0XY1tBgaWHl2sxFj/mULILaf+3zxpiWg
Jc8rWkUMpy1nP1OXUrCRBKbgr/loghUOEM6hozggeisDwpjh7Rm5OXZRj6JdO4QT
DLCl8NQKL8Ex33XoS45LoF2uuTfLt/E52CT0Sic4JdpwvIDTwlhxQR/Yo5gWuCnQ
L+J+zbclHjORG5EuIUsw
=VFRY
-----END PGP SIGNATURE-----
Merge tag 'mmc-v3.18-1' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Fix SDIO IRQ bug
- MMC regulator improvements
- Fix slot-gpio card detect bug
- Add support for Driver Stage Register
- Convert the common MMC OF parser to use GPIO descriptors
- Convert MMC_CAP2_NO_MULTI_READ into a callback, ->multi_io_quirk()
- Some additional minor fixes
MMC host:
- mmci: Support Qualcomm specific DML layer for DMA
- dw_mmc: Use common MMC regulators
- dw_mmc: Add support for Rock-chips RK3288
- tmio: Enable runtime PM support
- tmio: Add support for R-Car Gen2 SoCs
- tmio: Several fixes and improvements
- omap_hsmmc: Removed Balaji from MAINTAINERS
- jz4740: add DMA and pre/post support
- sdhci: Add support for Intel Braswell
- sdhci: Several fixes and improvements"
* tag 'mmc-v3.18-1' of git://git.linaro.org/people/ulf.hansson/mmc: (119 commits)
ARM: dts: fix MMC2 regulators for Exynos5420 Arndale Octa board
mmc: sdhci-acpi: Fix Braswell eMMC timeout clock frequency
mmc: sdhci-acpi: Pass HID and UID to probe_slot
mmc: sdhci-acpi: Get UID directly from acpi_device
mmc, sdhci, bcm-kona, LLVMLinux: Remove use of __initconst
mmc: sdhci-pci: Fix Braswell eMMC timeout clock frequency
mmc: sdhci: Let a driver override timeout clock frequency
mmc: sdhci-pci: Add Bay Trail and Braswell SD card detect
mmc: sdhci-pci: Set SDHCI_QUIRK2_STOP_WITH_TC for Intel BYT host controllers
mmc: sdhci-acpi: Add a HID and UID for a SD Card host controller
mmc: sdhci-acpi: Set SDHCI_QUIRK2_STOP_WITH_TC for Intel host controllers
mmc: sdhci: Add quirk for always getting TC with stop cmd
mmc: core: restore detect line inversion semantics
mmc: Fix incorrect warning when setting 0 Hz via debugfs
mmc: Fix use of wrong device in mmc_gpiod_free_cd()
mmc: atmel-mci: fix mismatched section on atmci_cleanup_slot
mmc: rtsx_pci: Set power related cap2 macros
mmc: core: Add new power_mode MMC_POWER_UNDEFINED
mmc: sdhci: execute tuning when device is not busy
mmc: atmel-mci: Release mmc resources on failure in probe
..
Braswell eMMC host controller specifies an incorrect
timeout clock frequncy in the capabilities registers.
The correct value is 1 MHz. A similar fix was done
for sdhci-pci, however in the sdhci-acpi case the
HID/UID is not unique so the capabilities register
values are matched also.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pass HID and UID to probe_slot so extra setup
can be done for specific ids.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
UID was made available on acpi_device since
commit ccf7804026 ("ACPI: Add _UID support for ACPI devices.")
Use it from there instead of reprocessing the
ACPI object info.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Clear QUEUE_FLAG_ADD_RANDOM in all block drivers that set
QUEUE_FLAG_NONROT.
Historically, all block devices have automatically made entropy
contributions. But as previously stated in commit e2e1a148 ("block: add
sysfs knob for turning off disk entropy contributions"):
- On SSD disks, the completion times aren't as random as they
are for rotational drives. So it's questionable whether they
should contribute to the random pool in the first place.
- Calling add_disk_randomness() has a lot of overhead.
There are more reliable sources for randomness than non-rotational block
devices. From a security perspective it is better to err on the side of
caution than to allow entropy contributions from unreliable "random"
sources.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The __initconst is in the wrong place, and when moved to the correct place
it uncovers an error where the variable is used by non-init data structures.
Instead merely make them const and put the const in the right spot.
Signed-off-by: Behan Webster <behanw@converseincode.com>
Reviewed-by: Mark Charlebois <charlebm@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Braswell eMMC host controller specifies an incorrect
timeout clock frequncy in the capabilities registers.
The correct value is 1 MHz.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let a driver override the timeout clock frequency by
populating it before calling sdhci_add_host(). Note
the value will otherwise be zero because sdhci_host is
zeroed when allocated.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for card detect for Bay Trail
and Braswell SD Card host controllers in PCI
mode.
This uses the gpio descriptor API which can find
gpio descriptors, for example, on an ACPI comapnion
device.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a HID (INT33BB) and UID (3) for a SD Card host controller.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a quirk for a host controller that always sets
a Transfer Complete interrupt status for the stop
command even when a busy response is not indicated.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit 98e90de99a
"mmc: host: switch OF parser to use gpio descriptors"
switched the semantic behaviour of card detect and read
only flags such that the inversion capability flag would
only be set if inversion was explicitly specified in the
device tree, in the hopes that no-one was using double
inversion.
It turns out that the XOR:ing between the explicit
inversion was indeed in use, so we need to restore the
old semantics where both ways of inversion are checked
and the end result XOR:ed.
Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Tested-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit 46420dd73b (PM / Domains: Add APIs to attach/detach a PM
domain for a device) started using errno values in pm.h header file.
It also failed to include the header for these, thus it caused
compiler errors.
Instead of including the errno header to pm.h, let's move the functions
to pm_domain.h, since it's a better match.
Fixes: 46420dd73b (PM / Domains: Add APIs to attach/detach a PM domain for a device)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is possible to turn off the card clock by setting
the frequency to zero via debugfs e.g.
echo 0 > /sys/kernel/debug/mmc0/clock
However that produces an incorrect warning that is
designed to warn if the frequency is below the minimum
operating frequency. So correct the warning.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_gpiod_free_cd() is paired with mmc_gpiod_request_cd()
and both must reference the same device which is the
actual host controller device not the mmc_host class
device.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As of 528bc7808f ("mmc: atmel-mci: Release mmc resources on failure in probe"),
the atmci_probe() function calls atmci_cleanup_slot in the failure path.
This causes a new warning whenever the driver is built:
WARNING: drivers/mmc/host/built-in.o(.init.text+0xa04): Section mismatch in reference from the function atmci_probe() to the function .exit.text:atmci_cleanup_slot()
The function __init atmci_probe() references
a function __exit atmci_cleanup_slot().
Gcc correctly warns about this function getting dropped in the link stage
for the built-in case, which would cause undefined behavior when this error
path is hit. The solution is to simply drop the __exit annotation.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 528bc7808f ("mmc: atmel-mci: Release mmc resources on failure in probe")
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Set MMC_CAP2_NO_PRESCAN_POWERUP and MMC_CAP2_FULL_PWR_CYCLE for
rtsx_pci_sdmmc and rtsx_usb_sdmmc to reflect properties of Realtek
card reader hosts.
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add MMC_POWER_UNDEFINED for power_mode in struct mmc_ios and use it as
the initial value of host->ios.power_mode.
For hosts with MMC_CAP2_NO_PRESCAN_POWERUP, this makes the later
mmc_power_off() do real power-off things instead of NOP, and further
prevents state messed up in cards that was already initialized (eg. by
BIOS of UEFI driver).
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We find tuning timeout because of the secure erase operation lasts too
long, so don't do tuning when device is busy.
Signed-off-by: Yi Sun <yi.y.sun@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This change takes care of releasing mmc resources on error cases in
probe function which was missing. Also release timer in remove function.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This change uses managed resource APIs to allocate resources such as,
clk, gpio, io in order to simplify the driver unload or failure cases.
Hence does away with release statements of the same resources in error
labels and remove function.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use the much more common pr_warn instead of pr_warning.
Other miscellanea:
o Coalesce formats
o Realign arguments
o Remove extra spaces when coalescing formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The same tuning block exists in the dw_mmc h.c and sdhci-msm.c
files. Move these into mmc.c so that they can be shared across
drivers.
Reported-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If we're tuning on a big-endian CPU we'll never determine we properly
tuned the device because we compare the data we received from the
controller with a table that assumes the CPU is little-endian.
Change the table to be an array of bytes instead of 32-bit words
so we can use memcmp() without needing to byte-swap every word
depending on the endianess of the CPU.
Cc: Asutosh Das <asutoshd@codeaurora.org>
Cc: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Reviewed-by: Georgi Djakov <gdjakov@mm-sol.com>
Fixes: 415b5a75da "mmc: sdhci-msm: Add platform_execute_tuning implementation"
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As soon as the CD IRQ is requested, it can trigger, since it's an
externally controlled event. If it does, delayed_work host->detect will
be scheduled.
Many host controller probe()s are roughly structured as:
*_probe() {
host = sdhci_pltfm_init();
mmc_of_parse(host->mmc);
rc = sdhci_add_host(host);
if (rc) {
sdhci_pltfm_free();
return rc;
}
In 3.17, CD IRQs can are enabled quite early via *_probe() ->
mmc_of_parse() -> mmc_gpio_request_cd() -> mmc_gpiod_request_cd_irq().
Note that in linux-next, mmc_of_parse() calls mmc_gpio*d*_request_cd()
rather than mmc_gpio_request_cd(), and mmc_gpio*d*_request_cd() doesn't
call mmc_gpiod_request_cd_irq(). However, this issue still exists if
mmc_gpio_request_cd() is called directly before mmc_start_host().
sdhci_add_host() may fail part way through (e.g. due to deferred
probe for a vmmc regulator), and sdhci_pltfm_free() does nothing to
unrequest the CD IRQ nor cancel the delayed_work. sdhci_pltfm_free() is
coded to assume that if sdhci_add_host() failed, then the delayed_work
cannot (or should not) have been triggered.
This can lead to the following with CONFIG_DEBUG_OBJECTS_* enabled, when
kfree(host) is eventually called inside sdhci_pltfm_free():
WARNING: CPU: 2 PID: 6 at lib/debugobjects.c:263 debug_print_object+0x8c/0xb4()
ODEBUG: free active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x18
The object being complained about is host->detect.
There's no need to request the CD IRQ so early; mmc_start_host() already
requests it. For most SDHCI hosts at least, the typical call path that
does this is: *_probe() -> sdhci_add_host() -> mmc_add_host() ->
mmc_start_host(). Therefore, remove the call to mmc_gpiod_request_cd_irq()
from mmc_gpio_request_cd(). This also matches mmc_gpio*d*_request_cd(),
which already doesn't call mmc_gpiod_request_cd_irq().
However, some host controller drivers call mmc_gpio_request_cd() after
mmc_start_host() has already been called, and assume that this will also
call mmc_gpiod_request_cd_irq(). Update those drivers to explicitly call
mmc_gpiod_request_cd_irq() themselves. Ideally, these drivers should be
modified to move their call to mmc_gpio_request_cd() before their call
to mmc_add_host(). However that's too large a change for stable.
This solves the problem (eliminates the kernel error message above),
since it guarantees that the IRQ can't trigger before mmc_start_host()
is called.
The critical point here is that once sdhci_add_host() calls
mmc_add_host() -> mmc_start_host(), sdhci_add_host() is coded not to
fail. In other words, if there's a chance that mmc_start_host() may have
been called, and CD IRQs triggered, and the delayed_work scheduled,
sdhci_add_host() won't fail, and so cleanup is no longer via
sdhci_pltfm_free() (which doesn't free the IRQ or cancel the work queue)
but instead must be via sdhci_remove_host(), which calls mmc_remove_host()
-> mmc_stop_host(), which does free the IRQ and cancel the work queue.
CC: Russell King <linux@arm.linux.org.uk>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexandre Courbot <acourbot@nvidia.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Previously only the ACPI PM domain was supported by the sdio bus.
Let's convert to the common attach/detach functions for PM domains,
which currently means we are extending the support to include the
generic PM domain as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
I spent a couple of days with the driver just hanging due to me forgetting to
specify the external crystal frequency, so that clk_get_rate() returned 0 and
thus the loop in tmio_mmc_set_clock() never ended. I don't think that's an
acceptable behavior, so I suggest that the minimum frequency is checked for 0
in tmio_mmc_host_probe().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Ian Molton <ian.molton@codethink.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current tmio is using sd_ctrl_read16/write16_rep()
for data transfer.
It works if transfer size was even number,
but, last 1 byte will be ignored if
transfer size was odd number.
This patch adds new tmio_mmc_transfer_data()
and solve this issue.
Tested-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Stop command errors are not fatal to the transfer since we make sure
that the card returns to the transfer state and check the card status.
Change an unnecessary error to an info.
Signed-off-by: Johan Rudholm <johanru@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dw_mci_of_find_slot_node() is only used in dw_mci_of_get_slot_quirks()
if CONFIG_OF is defined, thus there is no need to have a !CONFIG_OF
version of it. Fixes the following compile warning with !CONFIG_OF:
CC [M] drivers/mmc/host/dw_mmc.o
drivers/mmc/host/dw_mmc.c:2223:28: warning: ‘dw_mci_of_find_slot_node’ defined but not used [-Wunused-function]
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Checks EXT_CSD_PARTITION_SETTING_COMPLETED bit before
computing enhanced user area offset and size, and
adding mmc general purpose partitions. The two needs
EXT_CSD_PARTITION_SETTING_COMPLETED bit be set to be
valid (as described in JEDEC standard).
Warn user in case of misconfiguration.
Signed-off-by: Grégory Soutadé <gsoutade@neotion.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Replace ext_csd "enhanced_area_en" attribute by
"partition_setting_completed". It was used whether or
not enhanced user area is defined and without checks of
EXT_CSD_PARTITION_SETTING_COMPLETED bit.
Signed-off-by: Grégory Soutadé <gsoutade@neotion.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move code that manages user area and general purpose
partitions into functions.
Signed-off-by: Grégory Soutadé <gsoutade@neotion.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 0dcaa2499b improved error
handling of sdhci_add_host. However, "err_of_parse" and "err_cd_req"
should be placed after "pm_runtime_disable(&pdev->dev)".
Signed-off-by: Xiang Wang <wangx@marvell.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch renames sdio flag in vendor data to st_sdio, as this flag is
only used to enable ST specific sdio setup. This will also ensure that
the ST specfic setup is not done on other vendor like Qualcomm.
Originally the issue was detected while testing WLAN ath6kl on IFC6410
board with APQ8064 SOC.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds sdio enable mask in variant data, SOCs like ST have
special bits in datactrl register to enable sdio. Unconditionally setting
this bit in this driver breaks other SOCs like Qualcomm which maps this
bits to something else, so making this enable bit to come from variant
data solves the issue.
Originally the issue is detected while testing WLAN ath6kl on Qualcomm
APQ8064.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently the MMCI driver will only handle GPIO descriptors
implicitly through the device tree probe glue in mmc_of_init(),
but devices instatiated other ways such as through board files
and passing descriptors using the GPIO descriptor table will
not be able to exploit descriptors.
Augment the driver to look for a GPIO descriptor if device
tree is not used for the device, and if that doesn't work,
fall back to platform data GPIO assignment using the old
API. The end goal is to get rid of the platform data integer
GPIO assingments from the kernel.
This enable the MMCI-embedding platforms to be converted to
GPIO descritor tables.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This switches the central MMC OF parser to use gpio descriptors
instead of grabbing GPIOs explicitly from the device tree.
This strips out an unecessary use of the integer-based GPIO
API that we want to get rid of, cuts down on code as the
gpio descriptor code will handle active low flags.
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This makes it possible to get the write protect (read only)
GPIO line from a GPIO descriptor. Written to exactly mirror
the card detect function.
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When the slot GPIO driver gets the GPIO to be used for card
detect, it is now possible to specify a flag to have the line
set up as input. Get rid of the explicit setup call for input
and use the flag.
The extra argument works as there are transition varargs
macros in place in the <linux/gpio/consumer.h> header, in
the future we will make the flags argument compulsory.
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It seems very unlikely that eMMC devices would hold a standard
partitiontable in one of it's boot areas. Therefore, let's prevent
them from being scanned.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now, sh_mobile_sdhi can use .multi_io_quirk callback
instead of MMC_CAP2_NO_MULTI_READ flags.
let's use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now, tmio_mmc can use .multi_io_quirk callback
instead of MMC_CAP2_NO_MULTI_READ flags.
let's use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now, omap_hsmmc can use .multi_io_quirk callback
instead of MMC_CAP2_NO_MULTI_READ flags.
let's use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Due to HW issue, SDHCI host controller on Intel
Baytrail/Merrifield platforms can not use preset
register. So, disable preset registers for them by quirks.
Signed-off-by: Yunpeng Gao <yunpeng.gao@intel.com>
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Historically, we have been using MMC_CAP* to handle host HW issues and
currently the block layer uses MMC_CAP2_NO_MULTI_READ flag for a multi
I/O HW bug workaround.
There are a few tweaks needed to make MMC_CAP2_NO_MULTI_READ suite all
situations. Therefore let's add an optional host ops callback to enable
host drivers to return the number of blocks it allows per request.
In a future patch and when host drivers have converted to the new
callback, MMC_CAP2_NO_MULTI_READ shall be removed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Right now enable 1.2v IO voltage for SDHC is by using vqmmc.
Thus for the host which doesn't have vqmmc, or its vqmmc does
not support 1.2v, directly use MMC_CAP2_HS200 may cause HS200
failure.
So needs to check if vqmmc is able to support 1.2v. If it does
not support, disable 1.2v IO for HS200.
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Even (e)MMC card can support 3.3v to 1.2v vccq in DDR, but not all
host controller can support this, like some of the SDHCI host
which connect to an eMMC device. Some of these host controller
still needs to use 1.8v vccq for supporting DDR mode.
So the sequence will be:
if (host and device can both support 1.2v IO)
use 1.2v IO;
else if (host and device can both support 1.8v IO)
use 1.8v IO;
so if host and device can only support 3.3v IO, this is the last choice.
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Yunpeng Gao <yunpeng.gao@intel.com>
Tested-by: Jean-Michel Hautbois <jhautbois@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add the clock prepare and unprepare call to the driver set_ios calls
phase. This will remove a warning once the PXA architecture is migrated
to the clock infrastructure.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Similar to sdhci-pci controller, also add probe_slot
and remove_slot method in the sdhci-acpi driver.
Signed-off-by: Yunpeng Gao <yunpeng.gao@intel.com>
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is fully legal for a controller to start handling busy-end interrupt
before it has signaled that the command has completed. So make sure
we do things in the proper order, Or it results that command interrupt
is ignored so it can cause unexpected operations. This is founded at some
toshiba emmc with the bellow warning.
"mmc0: Got command interrupt 0x00000001 even though
no command operation was in progress."
This issue has been also reported by Youssef TRIKI:
It is not specific to Toshiba devices, and happens with eMMC devices
as well as SD card which support Auto-CMD12 rather than CMD23.
Also, similar patch is submitted by:
Gwendal Grignou <gwendal@chromium.org>
Changes since v1:
Fixed conflict with the next of git.linaro.org/people/ulf.hansson/mmc.git
and Tested if issue is fixed again.
Signed-off-by: Hankyung Yu <hankyung.yu@lge.com>
Signed-off-by: Chanho Min <chanho.min@lge.com>
Tested-by: Youssef TRIKI <youssef.triki@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_disable_irq_wakeups() is exported, but it is not called outside sdhci.c.
Make it static and do not export it, so that the following sparse warning is
fixed:
drivers/mmc/host/sdhci.c:2548:6: warning: symbol 'sdhci_disable_irq_wakeups' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The timeout_clk calculation code for SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK case
is common and could be moved into common sdhci_do_set_ios, then platform code
which is not using sdhci_set_clock does not need to write the same code again.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The timeout_clk calculation code in sdhci_add_host is meaningless for
SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK.
So only execute them with no SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK set.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The default sdhci driver write 0xE into timeout counter register to
set the maximum timeout. The value is not correct for uSDHC since the
max counter value for uSDHC is 0xF.
Instead of using common timeout code in sdhci, we implement esdhc_set_timeout
to handle the difference between eSDHC and uSDHC.
Currently we simply set the max timeout value as before.
But in the future, we probably may implement IMX specific timeout
setting algorithm and use suitable timeout for different CMDs.
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently the common code assume 0xE is the maximum timeout counter
value and use it to write into the timeout counter register.
However, it's fairly possible that some other SoCs may have different
max timeout register value. That means 0xE may be incorrect and
becomes meaningless.
It's also possible that other platforms has different timeout
calculation algorithm. To be flexible, this patch provides a .set_timeout
hook for those platforms to set the timeout on their way if they need.
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The default sdhci code use the 1 << 27 as the max timeout counter to
to calculate the max_busy_timeout, however it's not correct for uSDHC
since its the max counter is 1 << 28.
Implement esdhc_get_max_timeout_cout to handle it correctly.
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently the max timeout count is hardcode to 1 << 27 for calcuate
the max_busy_timeout, however, for some platforms the max timeout
count may not be 1 << 27, e.g. i.MX uSDHC is 1 << 28.
Thus 1 << 27 is not correct for such platform.
It is also possible that other platforms may have different values.
To be flexible, we add a get_max_timeout_count hook to get the correct
maximum timeout value for these platforms.
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's possible that mmc_of_parse() could return errors (possibly in
some future version it might return -EPROBE_DEFER even). Let's pass
those errors back.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
the implementation of CSR SDHCI controller is a modified version of
the one described in the 1.0 specification, and not a normal 3.0
controller.
and 8bit-width enable bit of CSR MMC hosts is 3, while stardard hosts
use bit 5.
this patch fixes the functionality of 8bit transfer in mmc controllers
and improve performance for mmc0 a lot.
Signed-off-by: Minda Chen <Minda.Chen@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Reviewed-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For UHS cards we need the ability to switch voltages from 3.3V to
1.8V. Add support to the dw_mmc driver to handle this. Note that
dw_mmc needs a little bit of extra code since the interface needs a
special bit programmed to the CMD register while CMD11 is progressing.
This means adding a few extra states to the state machine to track.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch makes use of mmc_regulator_get_supply() to handle
the vmmc and vqmmc regulators.Also it moves the code handling
the these regulators to dw_mci_set_ios().It turned on the vmmc
and vqmmc during MMC_POWER_UP and MMC_POWER_ON,and turned off
during MMC_POWER_OFF.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Declare ERASE capability so we can use filesystems with the discard
option and the fstrim tool.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The hardware is the same as used in Baytrail. Add these new PCI IDs to the
driver's list of supported IDs.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To support HS200 and UHS-1, we need add a big hunk of code,
as shown in the following patches. So a separate file for
rockchip SOCs is suitable.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some controller is supporting actual clock on SD_CLK_CTRL :: DIV[7:0].
Renesas SH-Mobile SDHI doesn't support,
but, Renesas R-Car SDHI supports it.
This patch adds new TMIO_MMC_CLK_ACTUAL flag for it.
[Kuninori Morimoto: tidyuped for upstreaming]
Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
TMIO clock is set via tmio_mmc_set_clock() -> tmio_mmc_clk_start(),
and SCLKEN bit will be set on tmio_mmc_clk_start().
It is not needed on tmio_mmc_set_clock() function.
The required clock setting will not be able to set
in some clocks without this patch.
Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds new TMIO_MMC_HAVE_CTL_DMA_REG flag,
and remove Renesas specific #ifdef from tmio driver
Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some controllers need to check SD bus status when writing data.
Then, it checks ILL_FUNC bit on SD_INFO2 register,
and this method is controlled via TMIO_MMC_HAS_IDLE_WAIT flags.
Same method is required on tmio_mmc_data_irq() which will
be called after writing data.
Current driver is checking CBSY bit for this purpose,
but, some controllers doesn't have CBSY bit.
This patch checks ILL_FUNC bit instead of CBSY bit
if it has TMIO_MMC_HAS_IDLE_WAIT flags
[Kuninori Morimoto: tidyuped for upstreaming]
Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Renesas R-Car SDHI should set reserved bits
on CTL_SDIO_STATUS register when writing.
This patch adds new TMIO_MMC_SDIO_STATUS_QUIRK flags
for this purpose
[Kuninori Morimoto: tidyuped for upstreaming
enabled this flags for all SH-Mobile/R-Car]
Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Renesas SDHI has "Multiple Block Transfer Mode" settings
on SD_CMD register which controls CMD12 automatically.
This patch cares it, because
CMD12 is not needed when CMD53 (= SD_IO_RW_EXTENDED)
[Kuninori Morimoto: tidyuped for upstreaming
enabled this flags for all SH-Mobile/R-Car]
Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Next card access will be always
error if it didn't clear error status
Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Basically, SD_BUF0 Tx/Rx addresses are same
in normal TMIO controller,
but, it is different on Renesas R-Car SDHI controller
if it uses DMAC
(Rx address needs to add 0x2000 to Tx address)
This patch adds new .dma_rx_offset and cares it
Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
These library functions aren't used and nor needed, let's remove them.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
At system PM suspend, the tmio core accessed the internal registers of
the controller without first moving the device into active state. This
caused a lock-up in system PM suspend phase.
The reason for the register access were masking of IRQs. Since that is
managed via the runtime PM suspend path, let's just re-use that path
for system PM suspend.
In other words force the device into runtime PM suspend state at system
PM suspend and restore it to active state at system PM resume.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
At system PM suspend, the tmio core accessed the internal registers of
the controller without first moving the device into active state. This
caused a lock-up in system PM suspend phase.
The reason for the register access were masking of IRQs. Since that is
managed via the runtime PM suspend path, let's just re-use that path
for system PM suspend.
In other words force the device into runtime PM suspend state at system
PM suspend and restore it to active state at system PM resume.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
To take advantage of the clock gating support, use the runtime PM
callbacks provided by the tmio core.
Additionally, we make use of the SET_PM_RUNTIME_PM_OPS, which is a
preparation needed to simplify system PM.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
To be able to simplify system PM, let's re-use the runtime PM callbacks
by converting to the SET_PM_RUNTIME_PM_OPS macro.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
To give the option for tmio hosts to use the runtime PM callbacks for
CONFIG_PM_SLEEP as well as CONFIG_PM_RUNTIME, move them to CONFIG_PM.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
To make sure we don't receive any spurious IRQs while we are inactive,
mask the IRQs from within the ->runtime_suspend() callback.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add clock gating control as a part of the tmio library functions for
runtime PM.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
An internal power state machine were beeing used to keep ->probe() and
->set_ios() in sync. Especially for handling specific scenarios while
using CONFIG_MMC_CLKGATE. Moreover dependency to CONFIG_MMC_CLKGATE
existed to handle runtime PM properly, which we moves away from here.
By removing the state machine and instead make ->set_ios() rely on the
information provided through the function's in-parameters, the code
becomes significantly simplier.
Additonally as a part of this rework we prepares for making the runtime
PM callbacks responsible of clock gating.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Move code for bus_width modification, out of the ->set_ios() callback
and into a separate function, to simplify code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Use runtime PM to keep the host active during I/O operations and other
requests which requires the tmio hardware to be powered.
Additionally make use of the runtime PM autosuspend feature with a
default timeout of 50 ms.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
The host must be kept active to be able to serve SDIO IRQs, thus let's
prevent it from going inactive while SDIO IRQ is enabled.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
The operation conditions register (OCR) stores the voltage
profile of the card, however the list of possible voltages
is restricted by the voltage range supported by the supply
used as VCC/VDD. So in mmc_vddrange_to_ocrmask() a OCR mask
is obtained to filter the not supported voltages, from the
value read in the host controller OCR register.
For fixed regulators, regulator_list_voltage() returns the
fixed output for the first selector but this doesn't happen
for switch (FET) regulators that obtain their voltage from
their parent supply. A call to regulator_get_voltage() is
needed in this case so the regulator core can return the
FET's parent supply voltage output.
This change is consistent with the fact that for other
fixed regulators (that are not FETs) the OCR mask is
returned even when mmc_regulator_set_ocr() checks if the
regulator is fixed before calling regulator_set_voltage().
Without this patch, the following warning is reported when
a FET is used as a vmmc-supply:
dwmmc_exynos 12220000.mmc: Failed getting OCR mask: -22
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some eMMC and SD cards implement a DSR register that allows to tune
raise/fall times and drive strength of the CMD and DATA outputs.
The values to use depend on the card in use and the host.
It might be needed to reduce the drive strength to prevent voltage peaks
above the host's specification.
Implement a 'dsr' devicetree property that allows to specify the value
to set the DSR to. For non-dt setups the new members of mmc_host can be
set by board code.
This patch was initially authored by Sascha Hauer. It contains
improvements authored by Markus Niebel and Uwe Kleine-König.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
.set_uhs_signaling field is currently initialised twice once to the
arch specific callback pxav3_set_uhs_signaling, and also to the generic
sdhci_set_uhs_signaling callback.
This means that uhs is currently broken for this platform currently, as pxav3
has some special constriants which means it can't use the generic callback.
This happened in
commit 96d7b78cfc ("mmc: sdhci: convert sdhci_set_uhs_signaling() into a library function")
commit a702c8abb2 ("mmc: host: split up sdhci-pxa, create sdhci-pxav3.c")'
Fix this and hopefully prevent it happening in the future by ensuring named
initialisers always follow the declaration order in the structure definition.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This allows us to get rid of the #else condition, as the macro compiles
away to nothing if not enabled.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This allows us to get rid of the #else condition, as the macro compiles
away to nothing if not enabled.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As the code is using SIMPLE_DEV_PM_OPS helper, this compiles away to
nothing if CONFIG_PM_SLEEP is disabled. Thus we don't need to #define
the suspend/resume callbacks to NULL.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As the code is using SIMPLE_DEV_PM_OPS helper, this compiles away to
nothing if CONFIG_PM_SLEEP is disabled. Thus we don't need to #define
the suspend/resume callbacks to NULL.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
781e989cf5 ("mmc: sdhci: convert to new SDIO IRQ handling") and
bf3b5ec66b ("mmc: sdio_irq: rework sdio irq handling") disabled
the use of our own custom threaded IRQ handler, but left in an
unconditional wake_up_process() on that handler at resume-time.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=80151
In addition, the check for MMC_CAP_SDIO_IRQ capability is added
before enable sdio IRQ.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
Signed-off-by: Fu Zhonghui <zhonghui.fu@linux.intel.com>
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are upcoming MIPS SoCs with dw_mmc hosts.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The dw_mmc drivers rely on the DMA API, so update the Kconfig entry
to depend on HAS_DMA. Since the drivers should build on any platform
with DMA, allow the driver to compile tested on non-ARC/ARM platforms.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
when SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK is set, timeout_clk is sdclk.
We need to update it when we change sdclk in sdhci_set_clock.
This allow to have a more precisse timeout and max_busy_timeout. This
can help for command that need a big busy wait (erase, ...).
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When we wait for busy after sending a command, if there is
a timeout, we got SDHCI_INT_DATA_TIMEOUT flags.
Before this commit we got the message :
"Got data interrupt 0x00100000 even though no data operation was in progress."
and we need to wait 10s that sdhci_timeout_timer expires.
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current code erroneously fill the last byte of R2 response with an undefined
value. In addition, the controller actually 'offloads' the last byte
(CRC7, end bit) while receiving R2 response and thus it's impossible to get the
actual value. This could cause mmc stack to obtain inconsistent CID from the
same card after resume and misidentify it as a different card.
Fix by assigning dummy CRC and end bit: {7'b0, 1} = 0x1 to the last byte of R2.
Cc: <stable@vger.kernel.org> # v3.16+
Fixes: c7f6558d84 ("mmc: Add realtek USB sdmmc host driver")
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current code erroneously fill the last byte of R2 response with an undefined
value. In addition, the controller actually 'offloads' the last byte
(CRC7, end bit) while receiving R2 response and thus it's impossible to get the
actual value. This could cause mmc stack to obtain inconsistent CID from the
same card after resume and misidentify it as a different card.
Fix by assigning dummy CRC and end bit: {7'b0, 1} = 0x1 to the last byte of R2.
Cc: <stable@vger.kernel.org> # v3.8+
Fixes: ff984e57d3 ("mmc: Add realtek pcie sdmmc host driver")
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If we happened to get a data error at just the wrong time the dw_mmc
driver could get into a state where it would never complete its
request. That would leave the caller just hanging there.
We fix this two ways and both of the two fixes on their own appear to
fix the problems we've seen:
1. Fix a race in the tasklet where the interrupt setting the data
error happens _just after_ we check for it, then we get a
EVENT_XFER_COMPLETE. We fix this by repeating a bit of code.
2. Fix it so that if we detect that we've got an error in the "data
busy" state and we're not going to do anything else we end the
request and unblock anyone waiting.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@gmail.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
curr should use signed type since it will contain the returned
value which is possible to be a negative value. Using u32 will
make the returned value to be true even there is a negative result.
Change to use int instead of u32
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make use of the MMC asynchronous request capability to prepare the
next DMA transfer request in parallel with the current transfer.
This is done by adding pre-request and post-request callbacks that are
used by the MMC framework during an active data transfer.
It should help reduce the impact of DMA preparation overhead on the SD
card performance.
Signed-off-by: Apelete Seketeli <apelete@seketeli.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Until now the MMC driver for JZ4740 SoC was relying on PIO mode only
for data transfers.
This patch allows the use of DMA for data trasnfers in addition to PIO
mode by relying on DMA Engine.
DMA tranfers performance might be further improved by taking advantage
of the asynchronous request capability of the MMC framework.
Signed-off-by: Apelete Seketeli <apelete@seketeli.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch focuses on clock setting for RK3288 mmc controller.
In RK3288 mmc controller, CLKDIV register can only be set 0 or 1,
and if DDR 8bit mode, CLKDIV register must be set 1.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The code selecting a device for the sdhci host has been
continuously tweaked (4b711cb138
"mmc: sdhci-pltfm: Add structure for host-specific data" and
a4d2177f00 "mmc: sdhci-pltfm: dt
device does not pass parent to sdhci_alloc_host" while there
does not seem to be any reason to use platform device's parent
in the first place.
The comment saying "Some PCI-based MFD need the parent here"
seem to refer to Timberdale FPGA driver (the only MFD driver
registering SDHCI cell, drivers/mfd/timberdale.c) but again,
the only situation when parent device matter is runtime PM,
which is not implemented for Timberdale.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no need for regulator consumers to include special logic for
fixed voltage regulators as they support regulator_set_voltage() just
like their non-fixed regulator counterparts.
Signed-off-by: Tim Kryger <tim.kryger@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On Qualcomm APQ8064 SOCs, SD card controller has an additional glue
called DML (Data Mover Local/Lite) to assist dma transfers.
This hardware needs to be setup before any dma transfer is requested.
DML itself is not a DMA engine, its just a gule between the SD card
controller and dma controller.
Most of this code has been ported from qualcomm's 3.4 kernel.
This patch adds the code necessary to intialize the hardware and setup
before doing any dma transfers.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Miscellaneous
- Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJT7PyAAAoJEFmIoMA60/r8kjQQALr/8oEfZoVcjgCb7waWOr25
hUTnrI6GBIAh/50hoBiPq0ouPCAKVv66+CUhuhFkLP7oJz+rMU0B9hfUvdLfmCpH
7ppaallkllT9nPFIr7h5RUWLXsoQyuHmCYmSrUCcnlT2LPgU0dN72YWElLisEM6Z
Pldg3933xyIQaCWviHjGEjWb7NvC+JY4pTkV5iyqGgU8Ale/eFYtLLSfdBEjIbGv
VDirYZmKELYeuncZPrTAsp4IENRMZn702wwDakMSODVMEWtJB5h4yrBawqQDlFP5
9ztIX6n9p9zkdVKbYZlx/Xwv6SYEnYXLxauVQMSO3Nck7Z10R5Ud+5uuCg/6mWH8
AQI4UV5bbJcg7zHgocTG9XLFLFPoPtD2JT6k6UT1LeUAiAOqcSzhRO+/qJBmJOWZ
Zv+EHXPlxBrl0zNifut6ZQrY17teuItVtmha70a/9W3PjnIx3KecqLcTwdTvDsOY
IAyH8WMZrBKpPpsczSmfE93i2Z1QRS91HEAOeSMxl/98dcDTdllYZS7spjoDll2f
xmpGDbpriLSCu2XsGHfTC9RbqA7CyuFlHggJSQDkT/5Esli0sCs7eweTuK3RVvPu
t6bUHK3yElb6x9qMZhb5q6l72wSMlGMishTdaxEHmqrEA8PtaIFodmVX2T/Zel5n
GHN6bysPqDItNR2v/3JX
=jJGu
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull DEFINE_PCI_DEVICE_TABLE removal from Bjorn Helgaas:
"Part two of the PCI changes for v3.17:
- Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)
It's a mechanical change that removes uses of the
DEFINE_PCI_DEVICE_TABLE macro. I waited until later in the merge
window to reduce conflicts, but it's possible you'll still see a few"
* tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Remove DEFINE_PCI_DEVICE_TABLE macro use
- Forward compatibility for eMMC.
- Fix some blacklisted cards with broken secure discard.
MMC host:
- mmci: Add support for Qualcomm variant.
- mmci: Fix regression for arm_variant.
- sdhci: Various fixes and cleanups.
- sdhci: Improve external VDD regulator support.
- sdhci: Support for DDR50 1.8V mode for BayTrail.
- sdhci-st: Add driver for ST SDHCI controller.
- sh-mmcif: DMA fixes.
- omap_hsmmc: Add support for SDIO interrupts.
- sdhci-pci: Add support for Intel Quark X1000.
- dw_mmc: Update the reset sequence.
- s3cmci: port DMA code to dmaengine API.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJT6K/QAAoJEP4mhCVzWIwpj5UP/3KWAsUCz5PlPaTxWgh/U+aN
lwO8aryFGjxfengCtJaw4cVksg3Lc5EvaSweg7BUqTucHoq/epdAU+Doqf5OVZ9Y
kicfx+WOAwIGTTuY9Wu7W884WgF+litZW4O4LtQnr6hHzx+xQhPabTc6zKJVS7WD
/Fx1Qcc0WFdGA3D0VdpCqGa7Y8IYk8cEP16MOA4s0HxZxONkjFbPdpQRF/zywGOA
tqJC7kAhlY+Rx5bsrr5Lvbhu2Ut+cfLBPdPYuJz50wnymQ15IrLj5n4rSd5GLY+f
HjMeCJzDHi1gk26wn3kYyWwz3JkJGWhtf6fC1hDqvkWEmHd872v7EuU9V4D3ehV1
xPVVVyUYqMgs0Vi+PXAlMhoajrwgnlM1Ox0sheOOefcaRoFVpV6PZOuAsAOfKRfC
ySOuEhOKn5OOvjH2TB4dNH1a3hegR9B3fJqjFe4UmUQP4FBicOfUKi+n6HwC+Omb
VDCuVvwmMCVPi/Lop6thpPepJBfR8Ncb3vanLpK64LcIjEfoPTwoAyNI32Qnry52
XMO4Tppl+bPzglGpV427KXlFbBwccp+8sCMRc/4lRiIMH9QhbZfVA1FcxwpvZ419
6SKXmqhA62nHLcWlQrRlvdnNyr+Ow2o5gJ0iVffByfmzcgPmja9YZYyDfx+DxWOo
W1oItq+qMd25rnnOPTLB
=kGSY
-----END PGP SIGNATURE-----
Merge tag 'mmc-v3.17-1' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC updates from Ulf Hansson:
"Me and Chris Ball decided to try out using my MMC tree as the primary
one, to simplify handling of patches.
This pull does thus contains all the MMC patches for 3.17 rc1, no pull
from Chris this time.
Details:
MMC core:
- forward compatibility for eMMC
- fix some blacklisted cards with broken secure discard
MMC host:
- mmci: Add support for Qualcomm variant
- mmci: Fix regression for arm_variant
- sdhci: Various fixes and cleanups
- sdhci: Improve external VDD regulator support
- sdhci: Support for DDR50 1.8V mode for BayTrail
- sdhci-st: Add driver for ST SDHCI controller
- sh-mmcif: DMA fixes
- omap_hsmmc: Add support for SDIO interrupts
- sdhci-pci: Add support for Intel Quark X1000
- dw_mmc: Update the reset sequence
- s3cmci: port DMA code to dmaengine API"
* tag 'mmc-v3.17-1' of git://git.linaro.org/people/ulf.hansson/mmc: (67 commits)
mmc: dw_mmc: modify the dt-binding for removing slot-node and supports-highspeed
mmc: dw_mmc: Slot quirk "disable-wp" is deprecated.
mmc: mmci: Reverse IRQ handling for the arm_variant
mmc: mmci: Move all CMD irq handling to mmci_cmd_irq()
mmc: mmci: Remove redundant check of status for DATA irq
mmc: dw_mmc: change to use recommended reset procedure
mmc: sdhci-pxav3: Use devm_* managed helpers
mmc: tmio: Configure DMA slave bus width
mmc: sh_mmcif: Configure DMA slave bus width
mmc: sh_mmcif: Fix DMA slave address configuration
mmc: sh_mmcif: Document DT bindings
mmc: sdhci-pci: remove PCI PM functions in suspend/resume callback
mmc: Do not advertise secure discard if it is blacklisted
mmc: sdhci-msm: Get COMPILE_TEST support
mmc: sdhci-msm: Remove unnecessary header file inclusion
mmc: sdhci-msm: Fix the binding example
mmc: sdhci: add DDR50 1.8V mode support for BayTrail eMMC Controller
mmc: sdhci: Preset value not supported in Baytrail eMMC
mmc: MMC_USDHI6ROL0 should depend on HAS_DMA
mmc: MMC_SH_MMCIF should depend on HAS_DMA
...
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit "mmc: mmci: Handle CMD irq before DATA irq", caused an issue
when using the ARM model of the PL181 and running QEMU.
The bug was reported for the following QEMU version:
$ qemu-system-arm -version
QEMU emulator version 2.0.0 (Debian 2.0.0+dfsg-2ubuntu1.1), Copyright
(c) 2003-2008 Fabrice Bellard
To resolve the problem, let's restore the old behavior were the DATA
irq is handled prior the CMD irq, but only for the arm_variant, which
the problem was reported for.
Reported-by: John Stultz <john.stultz@linaro.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Tested-by: Kees Cook <keescook@chromium.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch won't change the behavior of how mmci deals with CMD irqs.
By moving code from mmci_irq() to mmci_cmd_irq(), we getter a better
overview of what going on.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Tested-by: Kees Cook <keescook@chromium.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We don't need to verify the content of the status register twice, while
we are about to handle a DATA irq. Instead let's leave all verification
to be handled by mmci_data_irq().
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Tested-by: Kees Cook <keescook@chromium.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch changes the fifo reset code to follow the reset procedure
outlined in the documentation of Synopsys Mobile storage host databook.
Signed-off-by: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
[sonnyrao: fix compile for !CONFIG_MMC_DW_IDMAC case]
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Checkpatch fixes throughout the subsystem
- Use Regmap to handle IRQs in max77686, extcon-max77693 and mc13xxx-core
- Use DMA in rtsx_pcr
- Restrict building on unsupported architectures on timberdale, cs5535
- SPI hardening in cros_ec_spi
- More robust error handing in asic3, cros_ec, ab8500-debugfs,
max77686 and pcf50633-core
- Reorder PM runtime and regulator handing during shutdown in arizona
- Enable wakeup in cros_ec_spi
- Unused variable/code clean-up in pm8921-core, cros_ec, htc-i2cpld,
tps65912-spi, wm5110-tables and ab8500-debugfs
- Add regulator handing into suspend() in sec-core
- Remove pointless wrapper functions in extcon-max77693 and i2c-cros-ec-tunnel
- Use cross-architecture friendly data sizes in stmpe-i2c, arizona,
max77686 and tps65910
- Device Tree documentation updates throughout
- Provide power management support in max77686
- Few OF clean-ups in max77686
- Use manged resources in tps6105x
== New drivers/supported devices ==
- Add support for s2mpu02 to sec-core
- Add support for Allwinner A32 to sun6i-prcm
- Add support for Maxim 77802 in max77686
- Add support for DA9063 AD in da9063
- Add new driver for Intel PMICs (generic) and specifically Crystal Cove
== (Re-)moved drivers ==
- Move out keyboard functionality cros_ec ==> input/keyboard/cros_ec_keyb
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2cNI
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD update from Lee Jones:
"Changes to existing drivers:
- checkpatch fixes throughout the subsystem
- use Regmap to handle IRQs in max77686, extcon-max77693 and
mc13xxx-core
- use DMA in rtsx_pcr
- restrict building on unsupported architectures on timberdale,
cs5535
- SPI hardening in cros_ec_spi
- more robust error handing in asic3, cros_ec, ab8500-debugfs,
max77686 and pcf50633-core
- reorder PM runtime and regulator handing during shutdown in arizona
- enable wakeup in cros_ec_spi
- unused variable/code clean-up in pm8921-core, cros_ec, htc-i2cpld,
tps65912-spi, wm5110-tables and ab8500-debugfs
- add regulator handing into suspend() in sec-core
- remove pointless wrapper functions in extcon-max77693 and
i2c-cros-ec-tunnel
- use cross-architecture friendly data sizes in stmpe-i2c, arizona,
max77686 and tps65910
- devicetree documentation updates throughout
- provide power management support in max77686
- few OF clean-ups in max77686
- use manged resources in tps6105x
New drivers/supported devices:
- add support for s2mpu02 to sec-core
- add support for Allwinner A32 to sun6i-prcm
- add support for Maxim 77802 in max77686
- add support for DA9063 AD in da9063
- new driver for Intel PMICs (generic) and specifically Crystal Cove
(Re-)moved drivers ==
- move out keyboard functionality cros_ec ==> input/keyboard/cros_ec_keyb"
* tag 'mfd-for-linus-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (101 commits)
MAINTAINERS: Update MFD repo location
mfd: omap-usb-host: Fix improper mask use.
mfd: arizona: Only free the CTRLIF_ERR IRQ if we requested it
mfd: arizona: Add missing handling for ISRC3 under/overclocked
mfd: wm5110: Add new interrupt register definitions
mfd: arizona: Rename thermal shutdown interrupt
mfd: wm5110: Add in the output done interrupts
mfd: wm5110: Remove non-existant interrupts
mfd: tps65912-spi: Remove unused variable
mfd: htc-i2cpld: Remove unused code
mfd: da9063: Add support for AD silicon variant
mfd: arizona: Map MICVDD from extcon device to the Arizona core
mfd: arizona: Add MICVDD to mapped regulators for wm8997
mfd: max77686: Ensure device type IDs are architecture agnostic
mfd: max77686: Add Maxim 77802 PMIC support
mfd: tps6105x: Use managed resources when allocating memory
mfd: wm8997-tables: Suppress 'line over 80 chars' warnings
mfd: kempld-core: Correct a variety of checkpatch warnings
mfd: ipaq-micro: Fix coding style errors/warnings reported by checkpatch
mfd: si476x-cmd: Remedy checkpatch style complains
...
Use the clock framework to get the peripheral clock rate to
correctly set the MMC/SD bus clock divider.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7475/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch changes all absolute SYS_XY registers to offsets from the
SYS block base, prefixes them with AU1000 to avoid silent failures due
to changed addresses, and introduces helper functions to read/write
them.
No functional changes, comparing assembly of a few select functions shows
no differences.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7464/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Even though some implementations support 4-bytes data register access,
the tmio driver never configures the hardware in such a way and always
performs 2-bytes accesses. Hardcode the DMA transfer size to 2 bytes.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The data register is 4 bytes wide, hardcode the DMA transfer size to
4 bytes in both directions.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit e5a233cb64 ("mmc: sh_mmcif:
Factorize DMA channel request and configuration code") incorrectly
set the destination address for both slave channels instead of setting
the source address for the receive channel. Fix that.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is not required (in fact it even is not recommended) that a PCI
driver's suspend() callback save the standard configuration registers
of the device, prepare it for waking up the system, or put it into a
low-power state. All of these operations can very well be taken
care of by the PCI subsystem, without the driver's participation. Thus
remove these PCI functions.
For the device which has wake up capability, use device_init_wakeup to
init the wake up capability so that PCI core will help to enable the wakeup
for it.
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently when the device secure discard implementation is
blacklisted (MMC_QUIRK_SEC_ERASE_TRIM_BROKEN quirk is set)
instead of secure discard we're going to do normal discard,
which is wrong.
When the secure discard is known to be broken we should just
disallow it entirely and not advertise this functionality to
the user. Fix it.
Also move mmc_fixup_device() in from of mmc_blk_alloc() so we
can get quirks set before we attempt to set queue information.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The header <linux/regulator/consumer.h> is unused. Remove it.
Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is to enable DDR50 bus speed mode with 1.8V signaling capability
for BayTrail ACPI and PCI mode eMMC Controller.
Signed-off-by: Maurice Petallo <mauricex.r.petallo@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
"SDHCI_QUIRK2_PRESET_VALUE_BROKEN" quirk is added to prohibit
preset value enabling for Baytrail eMMC controller.
Signed-off-by: Maurice Petallo <mauricex.r.petallo@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If NO_DMA=y:
drivers/built-in.o: In function `usdhi6_dma_setup':
usdhi6rol0.c:(.text+0x5c35fc): undefined reference to `dma_map_sg'
drivers/built-in.o: In function `usdhi6_dma_stop_unmap':
usdhi6rol0.c:(.text+0x5c3738): undefined reference to `dma_unmap_sg'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If NO_DMA=y:
drivers/built-in.o: In function `sh_mmcif_start_dma_tx':
sh_mmcif.c:(.text+0x5a3286): undefined reference to `dma_map_sg'
drivers/built-in.o: In function `sh_mmcif_start_dma_rx':
sh_mmcif.c:(.text+0x5a33fc): undefined reference to `dma_map_sg'
drivers/built-in.o: In function `sh_mmcif_end_cmd':
sh_mmcif.c:(.text+0x5a3668): undefined reference to `dma_unmap_sg'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If NO_DMA=y:
drivers/built-in.o: In function `omap_hsmmc_pre_dma_transfer':
omap_hsmmc.c:(.text+0x5a0928): undefined reference to `dma_map_sg'
drivers/built-in.o: In function `omap_hsmmc_dma_cleanup':
omap_hsmmc.c:(.text+0x5a0e8e): undefined reference to `dma_unmap_sg'
drivers/built-in.o: In function `omap_hsmmc_dma_callback':
omap_hsmmc.c:(.text+0x5a1f58): undefined reference to `dma_unmap_sg'
drivers/built-in.o: In function `omap_hsmmc_post_req':
omap_hsmmc.c:(.text+0x5a2082): undefined reference to `dma_unmap_sg'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This platform driver adds initial support for the SDHCI host controller
found on STMicroelectronics SoCs.
It has been tested on STiH41x b2020 platforms currently.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This doesn't seem to be used any longer and removing the include fixes
64-bit ARM builds.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In case of reboot my olinuxino imx23 board does not see
mmc card any more. mmc_rescan is being called by delayed
work in loop, but mxs_mmc_get_cd always returns 0, so we
will never pass the card detection check and will not do
further card inition.
This patch is just an attempt to partially revert the patch
a91fe279ae of Sascha Hauer, where it is claimed that upper
layer will handle broken card detection using the polling
logic and MMC_CAP_NEEDS_POLL capability, but seems it is not
true, because upper logic still expects 1 from 'get_cd'.
So, here we always return 1 (card present) in case of
MMC_CAP_NEEDS_POLL capability set.
Signed-off-by: Roman Pen <r.peniaev@gmail.com>
CC: Chris Ball <chris@printf.net>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: Shawn Guo <shawn.guo@linaro.org>
CC: Ulf Hansson <ulf.hansson@linaro.org>
CC: linux-mmc@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use clk_prepare_enable/clk_disable_unprepare to make the driver
work properly with common clock framework.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As stated by the eMMC 5.0 specification, a chip should not be rejected
only because of the revision stated in the EXT_CSD_REV field of the
EXT_CSD register.
Remove the control on this value, the control of the CSD_STRUCTURE field
should be sufficient to reject future incompatible changes.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After the switch to the MMC core regulator infrastucture, we already
have a local "mmc" pointer in various functions. There is no longer a
need to access the data structure via host->mmc.
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC core in mmc_set_signal_voltage() already provides for the delay
required to switch to 1.8V, so there is no need for drivers to perform
this wait themselves.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
While merging the sdhci patchset from Russell King, somehow a blank
line was left behind. Let's correct the formatting.
Cc: Chris Ball <chris@printf.net>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A standard compliant SDHCI can itself supply VDD at 1.8, 3.0, or 3.3v.
Several vendors ignore this and instead rely upon external regulators
to supply VDD. While the external regulators typically can supply one
of the standard SDHCI voltage levels, there is no real reason for this
to be a hard requirement.
This patch alters the SDHCI driver such that external VDD regulators
that provide voltages other than the three mentioned above may be used
so long as they can supply a voltage that meets the needs of the card.
In the case that an external VDD regulator is provided, it is reasonable
to ignore the voltage capabilities of the host controller and allow the
external regulator to set the OCR mask. Additionally, there is no need
to convert a VDD voltage request into one of the standard SDHCI voltage
levels or program it in the host controller's power control register.
Signed-off-by: Tim Kryger <tim.kryger@gmail.com>
Tested-by: Sachin Kamat <spk.linux@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's a NOOP since 2.6.35 and it will be removed one day.
This is not trivial because current code uses hard coded 32 instead of
IRQF_DISABLED in the request_irq call.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For MMC_BUS_WIDTH_8 case, current code missed setting BM_EIGHTBIT_MODE bit.
Also has a small refactor to make the code looks better in readability.
So the bit settings witch below logic:
SDMMC_BUSMODE register:
Set EIGHTBIT_MODE bit for 8 bit mode, Set FOURBIT_MODE bit for 4 bit mode.
Clear both EIGHTBIT_MODE and FOURBIT_MODE bits for 1 bit mode.
SDMMC_EXTCTRL register:
Set EXT_EIGHTBIT bit for 8 bit mode, Clear EXT_EIGHTBIT bit for 1/4 bit mode.
Add define for EXT_EIGHTBIT to avoid using magic number.
BM_ONEBIT_MASK is no longer used, thus remove it.
This patch is untested due to lack of platform with 8-bit hardware.
However since the code is there, it's good to make the code match the document.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The initialization of some SD-cards fails because the card never
leaves the busy state. Aid trouble shooting by indicating this in the
kernel log.
Signed-off-by: Johan Rudholm <johanru@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
version.h inclusion is not needed as suggested by versioncheck.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The am335x can't detect pending cirq in PM runtime suspend.
This patch reconfigures dat1 as a GPIO before going to suspend.
SDIO interrupts are detected with the GPIO, the GPIO will only wake
the module from suspend, SDIO irq detection will still happen through the
IP block.
Idea of remuxing the pins by Tony Lindgren. Code contributions from
Tony Lindgren and Balaji T K <balajitk@ti.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
These are predefined states of the driver model. When not present,
as if not set in the device tree, they become no-ops.
Explicitly selecting the default state is not needed since the
device core layer sets pin mux to "default" state before probe.
This is not the simplest implementation, on AM335x at least, we could
switch to idle at any point in the suspend hook, only the default state
needs to be set before writing to the irq registers or an IRQ might get
lost.
Acked-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On multicores, an sdio irq handler could be running in parallel to
runtime suspend. In the worst case it could be waiting for the spinlock
held by the runtime suspend. When runtime suspend is complete and the
functional clock (fclk) turned off, the irq handler will continue and
cause a SIGBUS on the first register access.
Acked-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To detect sdio irqs properly without spurious events,
OMAP4 needs IWE in CON and CTPL, CLKEXTFREE in HCTL to be set
Tested-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add SDIO IRQ entries to debugfs entry. Note that PSTATE shows current
state of data lines, incl. SDIO IRQ pending
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There have been various patches floating around for enabling
the SDIO IRQ for hsmmc, but none of them ever got merged.
Probably the reason for not merging the SDIO interrupt patches
has been the lack of wake-up path for SDIO on some omaps that
has also needed remuxing the SDIO DAT1 line to a GPIO making
the patches complex.
This patch adds the minimal SDIO IRQ support to hsmmc for
omaps that do have the wake-up path. For those omaps, the
DAT1 line need to have the wake-up enable bit set, and the
wake-up interrupt is the same as for the MMC controller.
This patch has been tested on am3730 es1.2 with mwifiex
connected to MMC3 with mwifiex waking to Ethernet traffic
from off-idle mode. Note that for omaps that do not have
the SDIO wake-up path, this patch will not work for idle
modes and further patches for remuxing DAT1 to GPIO are
needed.
Based on earlier patches [1][2] by David Vrabel
<david.vrabel@csr.com>, Steve Sakoman <steve@sakoman.com>
For now, only support SDIO interrupt if we are booted with
a separate wake-irq configued via device tree. This is
because omaps need the wake-irq for idle states, and some
omaps need special quirks. And we don't want to add new
legacy mux platform init code callbacks any longer as we
are moving to DT based booting anyways.
To use it, you need to specify the wake-irq using the
interrupts-extended property.
[1] http://www.sakoman.com/cgi-bin/gitweb.cgi?p=linux.git;a=commitdiff_plain;h=010810d22f6f49ac03da4ba384969432e0320453
[2] http://comments.gmane.org/gmane.linux.kernel.mmc/20446
Acked-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no need for an output like this:
> mmcblk mmc1:0001: calling add_quirk_mmc+0x0/0x20
Instead use this one:
> mmcblk mmc1:0001: calling add_quirk_mmc
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the error path items that are no longer needed. The mmc card-detect
code cleans up after itself (and registers with devm) and the host error
is the same as the clock disable.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The pm_runtime call should implicitly disable the device once the
probe is over if there is no explicit reference gained. There is no
need to call pm_runtime_suspend() before the pm_runtime_disable()
call.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use devm_request_threaded_irq() for the host interrupt handlers so we
do not have to worry about freeing them on exit or error. Tidies up the
exit path code for the driver.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use the devm_clk_get() code to get the clock and allow it to be freed
automatically on release.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Start tidying the probe/release code by using devm_ioremap_resource() to
map the IO registers.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Change the initial print to show chip version and the bus rate it is
working at instead of the driver version. This is more useful information
as we already know which driver version from the kernel it is in.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove those unused ret variables to make it obvious that these function
will not return any errors in the current implementation.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Switch the common SDHCI code over to use mmc_host's regulator pointers
and remove the ones in the sdhci_host structure. Additionally, use the
common mmc_regulator_get_supply function to get the regulators and set
the ocr_avail mask.
This change sets the ocr_avail directly based upon the voltage ranges
supported which ensures ocr_avail is set correctly while allowing the
use of regulators that can't provide exactly 1.8v, 3.0v, or 3.3v.
Signed-off-by: Tim Kryger <tim.kryger@gmail.com>
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The runtime PM core handles a runtime_idle callback set to NULL as one
returning 0. So, let's just set it to NULL instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
This patch adds a fake Qualcomm ID 0x00051180 to the amba_ids, as Qualcomm
SDCC controller is pl180, but amba id registers read 0x0's.
The plan is to remove SDCC driver totally and use mmci as the main SD
controller driver for Qualcomm SOCs.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MCIFIFOCNT register behaviour on Qcom chips is very different than the other
pl180 integrations. MCIFIFOCNT register contains the number of
words that are still waiting to be transferred through the FIFO. It keeps
decrementing once the host CPU reads the MCIFIFO. With the existing logic and
the MCIFIFOCNT behaviour, mmci_pio_read will loop forever, as the FIFOCNT
register will always return transfer size before reading the FIFO.
Also the data sheet states that "This register is only useful for debug
purposes and should not be used for normal operation since it does not reflect
data which may or may not be in the pipeline".
This patch implements a qcom specific get_rx_fifocnt function which is
implemented based on status register flags. Based on qcom_fifo flag in
variant data structure, the corresponding get_rx_fifocnt function is selected.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On Controllers like Qcom SD card controller where cclk is mclk and mclk should
be directly controlled by the driver.
This patch adds support to control mclk directly in the driver, and also
adds explicit_mclk_control flag in variant structure giving more flexibility
to the driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
[Ulf Hansson] Fixed checkpatch warning
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some of the controller have maximum supported frequency, This patch adds
support in variant data structure to specify such restrictions. This
gives more flexibility in calculating the f_max before passing it to
mmc-core.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On some SOCs like Qcom there are explicit bits in the command register
to specify if its a data transfer command or not. So this patch adds
support to such bits in variant data, giving more flexibility to the
driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds edge support for data and command out to variant structure
giving more flexibility to the driver to support more SOCs which have
different clock register layout.
Without this patch other new SOCs like Qcom will have to add more code to
special case them
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
[Ulf Hansson] Resolved conflict
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds 8bit bus enable to variant structure giving more flexibility
to the driver to support more SOCs which have different clock register layout.
Without this patch other new SOCs like Qcom will have to add more code
to special case them.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
[Ulf Hansson] Resolved conflict
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds ddrmode mask to variant structure giving more flexibility
to the driver to support more SOCs which have different datactrl register
layout.
Without this patch datactrl register is updated with incorrect ddrmode mask,
resulting in failures on Qualcomm SD Card Controller.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
[Ulf Hansson] Resolved conflict
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instance of this IP on Qualcomm's SOCs has bit different layout for datactrl
register. Bit position datactrl[16:4] hold the true block size instead of power
of 2.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On Qcom SD Card controller POWER, CLKCTRL, DATACTRL and COMMAND registers
should be updated in MCLK domain, and writes to these registers must be
separated by three MCLK cycles. This resitriction is not applicable for
other registers. Any subsequent writes to these register will be ignored
until 3 MCLK have passed.
One usec delay between two CMD register writes is not sufficient in the
card identification phase where the CCLK is very low. This patch replaces
a static 1 usec delay to use mmci_reg_delay function which can provide
correct delay depending on the cclk frequency.
Without this patch the card is not detected.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a Qualcomm SD Card controller specific register variations
to header file. Qualcomm SDCC controller is pl180, with slight changes in
the register layout from standard pl180 register set.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch replaces a constant used in calculating timeout with a proper
macro. This is make code more readable.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull networking updates from David Miller:
1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.
2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
Benniston.
3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
Mork.
4) BPF now has a "random" opcode, from Chema Gonzalez.
5) Add more BPF documentation and improve test framework, from Daniel
Borkmann.
6) Support TCP fastopen over ipv6, from Daniel Lee.
7) Add software TSO helper functions and use them to support software
TSO in mvneta and mv643xx_eth drivers. From Ezequiel Garcia.
8) Support software TSO in fec driver too, from Nimrod Andy.
9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.
10) Handle broadcasts more gracefully over macvlan when there are large
numbers of interfaces configured, from Herbert Xu.
11) Allow more control over fwmark used for non-socket based responses,
from Lorenzo Colitti.
12) Do TCP congestion window limiting based upon measurements, from Neal
Cardwell.
13) Support busy polling in SCTP, from Neal Horman.
14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.
15) Bridge promisc mode handling improvements from Vlad Yasevich.
16) Don't use inetpeer entries to implement ID generation any more, it
performs poorly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
tcp: fixing TLP's FIN recovery
net: fec: Add software TSO support
net: fec: Add Scatter/gather support
net: fec: Increase buffer descriptor entry number
net: fec: Factorize feature setting
net: fec: Enable IP header hardware checksum
net: fec: Factorize the .xmit transmit function
bridge: fix compile error when compiling without IPv6 support
bridge: fix smatch warning / potential null pointer dereference
via-rhine: fix full-duplex with autoneg disable
bnx2x: Enlarge the dorq threshold for VFs
bnx2x: Check for UNDI in uncommon branch
bnx2x: Fix 1G-baseT link
bnx2x: Fix link for KR with swapped polarity lane
sctp: Fix sk_ack_backlog wrap-around problem
net/core: Add VF link state control policy
net/fsl: xgmac_mdio is dependent on OF_MDIO
net/fsl: Make xgmac_mdio read error message useful
net_sched: drr: warn when qdisc is not work conserving
...
We have a number of front-end drivers for SDHCI_PLTFM, some of them
use 'select MMC_SDHCI_PLTFM', others use 'depends on'. This is
inconsistent and confusing, and in one case has also led to a
build error because of incomplete dependencies:
warning: (MMC_SDHCI_PXAV3 && MMC_SDHCI_PXAV2 && MMC_SDHCI_BCM_KONA) selects MMC_SDHCI_PLTFM which has unmet direct dependencies (MMC && MMC_SDHCI)
drivers/built-in.o: In function `sdhci_sirf_resume':
:(.text+0xaaacb4): undefined reference to `sdhci_resume_host'
drivers/built-in.o: In function `sdhci_sirf_suspend':
:(.text+0xaaacf8): undefined reference to `sdhci_suspend_host'
drivers/built-in.o: In function `sdhci_sirf_probe':
:(.text+0xaaaf44): undefined reference to `sdhci_add_host'
:(.text+0xaaaf50): undefined reference to `sdhci_remove_host'
This changes Kconfig to use 'depends on MMC_SDHCI_PLTFM' for all these
cases, to fix the build error and make the logic more logical.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC host driver should not select the pmic driver, since that
may have other dependencies, notably i2c in this case. It's not
clear what the exact requirement of the driver is, but to preserve
the behavior, this patch changes the 'select' into 'depends on',
meaning you now have to turn on TPS65010 explicitly and then
MMC_OMAP.
Found during randconfig build testing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: linux-omap@vger.kernel.org
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
gcc correctly points out that hw_state can be used uninitially
in the mvsd_setup_data() function. This rearranges the function
to ensure it always contains a proper value.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Chris Ball <chris@printf.net>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: linux-mmc@vger.kernel.org
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This avoids a build error due to the use of flush_dcache_page.
drivers/mmc/host/atmel-mci.c: In function 'atmci_read_data_pio':
drivers/mmc/host/atmel-mci.c:1870:5: error: implicit declaration of function 'flush_dcache_page' [-Werror=implicit-function-declaration]
flush_dcache_page(sg_page(sg));
^
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci core was refactored recently and some of those
refactorings required changes in every sdhci platform driver.
Those updates happened around the same time as when the msm
driver was merged so the refactorings missed the msm driver.
Hook in the basic library functions so that we can boot apq8074
dragonboards again instead of crashing when we try to jump to
NULL function pointers.
Reported-by: Kevin Hilman <khilman@linaro.org>
Cc: Georgi Djakov <gdjakov@mm-sol.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Kumar Gala <galak@codeaurora.org>
Reviewed-by: Georgi Djakov <gdjakov@mm-sol.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix a number of wrong print formats.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Core:
- support HS400 mode of eMMC 5.0, via DT bindings mmc-hs400-1_{2,8}v
- if card init at 3.3v doesn't work, try 1.8v and 1.2v too
Drivers:
- moxart: New driver for MOXA ART SoCs
- rtsx_usb_sdmmc: New driver for Realtek USB card readers
- sdhci: Large rework around IRQ/regulator handling, remove card_tasklet
- sdhci-pci-o2micro: Add SeaBird SeaEagle SD3 support
- sunxi: New driver for Allwinner sunxi SoCs
- usdhi6rol0: New driver for Renesas SD/SDIO controller
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OZao
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC update from Chris Ball:
"MMC highlights for 3.16:
Core:
- support HS400 mode of eMMC 5.0, via DT bindings mmc-hs400-1_{2,8}v
- if card init at 3.3v doesn't work, try 1.8v and 1.2v too
Drivers:
- moxart: New driver for MOXA ART SoCs
- rtsx_usb_sdmmc: New driver for Realtek USB card readers
- sdhci: Large rework around IRQ/regulator handling, remove card_tasklet
- sdhci-pci-o2micro: Add SeaBird SeaEagle SD3 support
- sunxi: New driver for Allwinner sunxi SoCs
- usdhi6rol0: New driver for Renesas SD/SDIO controller"
* tag 'mmc-updates-for-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (95 commits)
mmc: sdhci-s3c: use mmc_of_parse and remove the card_tasklet
mmc: add a driver for the Renesas usdhi6rol0 SD/SDIO host controller
mmc: sdhci-of-esdhc: Fixup compile error
mmc: tegra: fix reporting of base clock frequency
mmc: tegra: disable UHS modes
mmc: sdhci-dove: use mmc_of_parse() and remove card_tasklet CD handler
MAINTAINERS: mmc: Add path to git tree
mmc: dove: fix missing MACH_DOVE dependency
mmc: sdhci: SD tuning is broken for some controllers
mmc: sdhci-esdhc-imx: fix mmc ddr mode regression issue
mmc: sdhci-pci-o2micro: Add SeaBird SeaEagle SD3 support
mmc: omap_hsmmc: split omap-dma header file
mmc: omap_hsmmc: fix cmd23 multiblock read/write
mmc: omap_hsmmc: use devm_ioremap_resource
mmc: omap_hsmmc: use devm_request_threaded_irq
mmc: omap_hsmmc: use devm_request_irq
mmc: omap_hsmmc: use devm_clk_get
mmc: sunxi: Add driver for SD/MMC hosts found on Allwinner sunxi SoCs
mmc: wmt-sdmmc: Use GFP_KERNEL instead of hard-coded value
mmc: omap: Use DIV_ROUND_UP instead of open coded
...
driver additions and fixes. There are additions to the clock core code
for some of the basic types (e.g. the common divider type has some fixes
and featured added to it).
One minor annoyance is a last-minute dependency that wasn't handled
quite right. ba0fae3 in this pull request depends on
include/dt-bindings/clock/berlin2.h, which is already in your tree via
the arm-soc pull request. Building for the berlin platform will break
when the clk tree is built on it's own, but merged into your master
branch everything should be fine.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=2AAL
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.16' of git://git.linaro.org/people/mike.turquette/linux into next
Pull clock framework updates from Mike Turquette:
"The clock framework changes for 3.16 are pretty typical: mostly clock
driver additions and fixes. There are additions to the clock core
code for some of the basic types (e.g. the common divider type has
some fixes and featured added to it).
One minor annoyance is a last-minute dependency that wasn't handled
quite right. Commit ba0fae3b06 ("clk: berlin: add core clock driver
for BG2/BG2CD") in this pull request depends on
include/dt-bindings/clock/berlin2.h, which is already in your tree via
the arm-soc pull request. Building for the berlin platform will break
when the clk tree is built on it's own, but merged into your master
branch everything should be fine"
* tag 'clk-for-linus-3.16' of git://git.linaro.org/people/mike.turquette/linux: (75 commits)
mmc: sunxi: Add driver for SD/MMC hosts found on Allwinner sunxi SoCs
clk: export __clk_round_rate for providers
clk: versatile: free icst on error return
clk: qcom: Return error pointers for unimplemented clocks
clk: qcom: Support msm8974pro global clock control hardware
clk: qcom: Properly support display clocks on msm8974
clk: qcom: Support display RCG clocks
clk: qcom: Return highest rate when round_rate() exceeds plan
clk: qcom: Fix mmcc-8974's PLL configurations
clk: qcom: Fix clk_rcg2_is_enabled() check
clk: berlin: add core clock driver for BG2Q
clk: berlin: add core clock driver for BG2/BG2CD
clk: berlin: add driver for BG2x complex divider cells
clk: berlin: add driver for BG2x simple PLLs
clk: berlin: add driver for BG2x audio/video PLL
clk: st: Terminate of match table
clk/exynos4: Fix compilation warning
ARM: shmobile: r8a7779: Add clock index macros for DT sources
clk: divider: Fix overflow in clk_divider_bestdiv
clk: u300: Terminate of match table
...
Fix the compile error.
(Removed the card_tasklet at "mmc: sdhci: push card_tasklet into treaded irq handler")
drivers/mmc/host/sdhci-s3c.c: In function ‘sdhci_s3c_notify_change’:
drivers/mmc/host/sdhci-s3c.c:402:25: error: ‘struct sdhci_host’ has no member named ‘card_tasklet’
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
The Allwinner sunxi mmc host uses dma in bus-master mode using a built-in
designware idmac controller, which is identical to the one found in the mmc-dw
hosts. However the rest of the host is not identical to mmc-dw, it deals with
sending stop commands in hardware which makes it significantly different
from the mmc-dw devices.
Signed-off-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch>
[hdegoede@redhat.com: various cleanups and fixes]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Chris Ball <chris@printf.net>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch adds a driver for the Renesas usdhi6rol0 SD/SDIO host controller
in both PIO and DMA modes.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Chris Ball <chris@printf.net>
- Put the device into low power state at system suspend.
- Convert to the common mmc DT parser.
- Add missing DT bindings needed for ux500.
Updates for ARM ux500|u300:
- Convert to the common mmc DT bindings.
- Remove redundant board file for mmci platform data.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=09ec
-----END PGP SIGNATURE-----
Merge tag 'mmc-v3.16-1' of git://git.linaro.org/people/ulf.hansson/mmc into next
Pull MMC update from Ulf Hansson:
"These patches are mainly updates for the mmci driver and have been
tested in linux-next.
Some ARM SoC related patches are also included and those have been
acked from the corresponding maintainers to go through my mmc tree.
Updates for mmci driver:
- Put the device into low power state at system suspend.
- Convert to the common mmc DT parser.
- Add missing DT bindings needed for ux500.
Updates for ARM ux500|u300:
- Convert to the common mmc DT bindings.
- Remove redundant board file for mmci platform data"
* tag 'mmc-v3.16-1' of git://git.linaro.org/people/ulf.hansson/mmc: (22 commits)
mmc: mmci: Enforce DMA configuration through DT
mmc: mmci: Enforce max frequency configuration through DT
mmc: mmci: Enforce mmc capabilities through DT
mmc: mmci: Enforce DT for signal direction and feedback clock
ARM: ux500: Remove redundant board file for mmci platform data
ARM: ux500: Add a vmmc regulator through DT for the poped eMMC for href
ARM: ux500: Add the mmc capabilities flags to DT
mmc: mmci: Enable MMC_CAP_CMD23
mmc: mmci: Mark the DT bindings for highspeed mode as deprecated
ARM: u300: Convert to the common mmc DT bindings for highspeed mode
ARM: nomadik: Convert to the common mmc DT bindings for highspeed mode
ARM: ux500: Convert to the common mmc DT bindings for highspeed mode
ARM: ux500: Add mmci signal directions and feeback clock in DT for href
mmc: mmci: Use the common mmc DT parser
mmc: mmci: Add DT bindings for feedback clock pin
mmc: mmci: Add DT bindings for signal direction
mmc: mmci: Update DT documentation
mmc: mmci: Convert to devm functions
mmc: mmci: Convert to the mmc gpio API
mmc: mmci: Put the device into low power state at system suspend
...
Remove the option to provide DMA configuration as platform data,
enforce it through DT.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tegra SDHCI controllers, by default, report a base clock frequency of
208Mhz in SDHCI_CAPABILTIES which may or may not be equal to the actual
base clock frequency. This is because the clock rate is configured by
the clock controller, which is external to the SD/MMC controller. Since
the SD/MMC controller has no knowledge of how this clock is configured,
it will simply report the maximum frequency. While the reported value
can be overridden by setting BASE_CLK_FREQ in VENDOR_CLOCK_CTRL on
Tegra30 and later SoCs, just set CAP_CLOCK_BASE_BROKEN and supply
sdhci_pltfm_clk_get_max_clock(), which simply does a clk_get_rate(),
as the get_max_clock() callback.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Program TEGRA_SDHCI_VENDOR_MISC_CTRL so that UHS modes aren't advertised
in SDHCI_CAPABILITIES_1. While the Tegra SDHCI controller does support
these modes, they require Tegra-specific tuning and calibration routines
which the driver does not support yet.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
f8ec589b86 ("mmc: sdhci-dove: allow GPIOs to be used for card detection
on Dove" added a gpio based card detect interrupt handler that was hooked
up into card_tasket.
3560db8e24 ("mmc: sdhci: push card_tasklet into threaded irq handler")
now removed that very card_tasklet causing sdhci-dove to fail on build
with:
drivers/mmc/host/sdhci-dove.c: In function 'sdhci_dove_carddetect_irq':
drivers/mmc/host/sdhci-dove.c:42:24: error: 'struct sdhci_host' has no member named 'card_tasklet'
To fix both the build error and get a working gpio card detection without
card_tasklet, replace sdhci_get_of_property() with more recent
mmc_of_parse(). It takes care of gpio-based card detect passed through DT
already and allows to remove the offending code sections dealing with
removed card_tasklet.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
DT-enabled Dove moved over from ARCH_DOVE in mach-dove to MACH_DOVE in
mach-mvebu. As non-DT ARCH_DOVE will stay to rot for a while, add a new
DT-only MACH_DOVE Kconfig. This slipped through the cracks and now is
a fix to allow to build Dove's SDHCI driver for mach-mvebu on v3.15-rc.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
NeilBrown
Ondrej Zary
Abhilash Kesavan
Johan Rudholm
Andreas Fenkart
Wenyou Yang
Adrian Hunter
Prabu Thangamuthu
Vincent Wan
Mark Brown
Timo Kokkonen
Sebastian Hesselbarth
Mike Looijmans
Ulf Hansson
Doug Anderson
Dan Carpenter
Alexandre Belloni
Gwendal Grignou
Sonny Rao
Tomeu Vizoso
Srinivas Kandagatla
Andrew Gabbasov
Dirk Behme
Matteo Facchinetti
Peter Guo
Baruch Siach
Kristina Martsenko
Wolfram Sang
Linus Torvalds
Mike Snitzer
Behan Webster
Linus Walleij
Arnd Bergmann
Roger Tseng
Yi Sun
Pramod Gurav
Joe Perches
Stephen Boyd
Stephen Warren
Sergei Shtylyov
Kuninori Morimoto
Tobias Klauser
Grégory Soutadé
Xiang Wang
Gao, Yunpeng
Chuanxiao.Dong
Robert Jarzmik
Chanho Min
Fabio Estevam
Aisheng Dong
Geert Uytterhoeven
Minda Chen
Yuvaraj CD
Chen-Yu Tsai
Alan Cox
addy ke
Shinobu Uehara
Nicolas Ferre
Javier Martinez Canillas
Sascha Hauer
Peter Griffin
Fu Zhonghui
Andrew Bresticker
Matthieu CASTET
Wei Yongjun
Apelete Seketeli
Pawel Moll
Tim Kryger
Bartlomiej Zolnierkiewicz
Benoit Taine
Jaehoon Chung
Laurent Pinchart
Manuel Lauss
Lukas Czerner
Georgi Djakov
Maurice Petallo
Geert Uytterhoeven
Micky Ching
Vasily Khoruzhick
Thierry Reding
Roman Peniaev
Romain Izard
Markus Mayer
Russell King
Derek Browne
Axel Lin
Sachin Kamat
Balaji T K
Alexander Stein
Ben Dooks
Markus Pargmann
Guennadi Liakhovetski
David Lanzendörfer
Lee Jones
John W. Linville