Add the DT nodes for the network-on-chip interconnect buses found
on sc7280-based platforms.
Signed-off-by: Odelu Kukatla <okukatla@codeaurora.org>
Link: https://lore.kernel.org/r/1619517059-12109-4-git-send-email-okukatla@codeaurora.org
[bjorn: Sorted nodes and dropped include]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Huawei Ascend G7 supports NFC using the NXP PN547, which is
supported by the nxp-nci-i2c driver in mainline. It seems to detect
NFC tags using "nfctool" just fine, although it seems like there
are not really any useful applications making use of the Linux NFC
subsystem. :(
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210514104328.18756-5-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The display on the Huawei Ascend G7 is supplied by a TI TPS65132
regulator. The panel needs a driver in mainline first, but the
TPS65132 is already supported in mainline by the tps65132 driver.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210514104328.18756-4-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Huawei Ascend G7 has a Synaptics "C199HW-006" touchscreen,
supplied by pm8916_l17 and pm8916_l16. Add it to the device tree
and reduce the maximum allowed voltage for pm8916_l16 to 1.8V since
we really should not use more for an I/O supply.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210514104328.18756-2-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Huawei Ascend G7 is a smartphone from Huawei based on MSM8916.
It's fairly similar to the other MSM8916 devices, the only notable
exception are the "cd-gpios" for detecting if a SD card was inserted:
It looks like Huawei forgot to re-route this to gpio38, so the correct
GPIO seems to be gpio56 on this device.
Note: The original firmware from Huawei can only boot 32-bit kernels.
To boot arm64 kernels it is necessary to flash 64-bit TZ/HYP firmware
with EDL, e.g. taken from the DragonBoard 410c. This works because Huawei
forgot to set up (firmware) secure boot for some reason.
Also note that Huawei no longer provides bootloader unlock codes.
This can be bypassed by patching the bootloader from a custom HYP firmware,
making it think the bootloader is unlocked. I use a modified version of
qhypstub [1], that patches a single instruction in the Huawei bootloader.
The device tree contains initial support for the Huawei Ascend G7 with:
- UART (untested, probably available via some test points)
- eMMC/SD card
- Buttons
- Notification LED (combination of 3 GPIO LEDs)
- Vibrator
- WiFi/Bluetooth (WCNSS)
- USB
[1]: https://github.com/msm8916-mainline/qhypstub
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210514104328.18756-1-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This spi flash part is actually being clocked at 37.5MHz, not 25MHz,
because of the way the clk driver is rounding up the rate that is
requested to the nearest supported frequency. Let's update the frequency
here, and remove the TODO because this is the fastest frequency we're
going to be able to use here.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210519054030.3217704-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This compatible string isn't present upstream. Let's drop the node as it
isn't used.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210601185959.3101132-2-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This compatible string isn't present upstream. Let's drop the node as it
isn't used.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210601185959.3101132-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
We don't use the PON module on Trogdor devices. Instead the reboot
reason is sort of stored in the 'eventlog' and the bootloader figures
out if the boot is abnormal and records that there. Disable the PON node
and then drop the power key disabling because that's a child node that
will no longer be enabled if the PON node is disabled.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210601184417.3020834-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
On coachz it could be observed that SPI_CLK voltage level was only
1.4V during active transfers because the drive strength was too
weak. The line hadn't finished slewing up by the time we started
driving it down again. Using a drive strength of 8 lets us achieve the
correct voltage level of 1.8V.
Though the worst problems were observed on coachz hardware, let's do
this across the board for trogdor devices. Scoping other boards shows
that this makes the clk line look nicer on them too and doesn't
introduce any problems.
Only the clk line is adjusted, not any data lines. Because SPI isn't a
DDR protocol we only sample the data lines on either rising or falling
edges, not both. That means the clk line needs to toggle twice as fast
as data lines so having the higher drive strength is more important
there.
Signed-off-by: Wenchao Han <hanwenchao@huaqin.corp-partner.google.com>
[dianders: Adjust author real name; adjust commit message]
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210510075253.1.Ib4c296d6ff9819f26bcaf91e8a08729cc203fed0@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add initial DTSI for RZ/G2{L,LC} SoC's.
File structure:
r9a07g044.dtsi => RZ/G2L family SoC common parts
r9a07g044l1.dtsi => RZ/G2L R9A07G044L1 SoC specific parts
r9a07g044l2.dtsi => RZ/G2L R9A07G044L2 SoC specific parts
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210609153230.6967-11-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Although the schematics of Pine A64-LTS and SoPine Baseboard shows both
the RX and TX internal delay are enabled, they're using the same broken
RTL8211E chip batch with Pine A64+, so they should use TXID instead, not
ID.
In addition, by checking the real components soldered on both a SoPine
Baseboard and a Pine A64-LTS, RX delay is not enabled (GR69 soldered and
GR70 NC) despite the schematics says it's enabled. It's a common
situation for Pine64 boards that the NC information on schematics is not
the same with the board.
So the RGMII delay mode should be TXID on these boards.
Fixes: c2b111e59a ("arm64: dts: allwinner: A64 Sopine: phy-mode rgmii-id")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210609083843.463750-1-icenowy@aosc.io
Add a basic GPU node for mt8183, as well as OPP table.
Note that with the current panfrost driver, devfreq is not
actually functional, as the we do not have platform-specific
support for >1 supplies. Also, we are missing code to handle
frequency change, as the GPU frequency needs to be switched
away to a stable 26Mhz clock during the transition.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Link: https://lore.kernel.org/r/20210521200038.v14.1.I9f45f5c1f975422d58b5904d11546349e9ccdc94@changeid
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add tboard thermal zones.
The tboard thermal sensors are a kind of NTC sensors which are located
on PCB board to correlate the temperature of the case (Tskin).
pull-up voltage: 1800 mv
pull-up resistor: 75K
Vsense = pull-up voltage * Rntc / ( pull-up resistor + Rntc )
AuxIn = Vsense * 4096 / 1500
Signed-off-by: Michael Kao <michael.kao@mediatek.com>
Signed-off-by: Ben Tseng <ben.tseng@mediatek.com>
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
Link: https://lore.kernel.org/r/20210604093755.13288-1-ben.tseng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add a 'cbas' device node for supporting tablet mode switch in
kukui devices.
Kukui platforms with detacheable base have an additional input
device under cros-ec, which reports SW_TABLET_MODE regarding
its base state (e.g. base flipped or detached).
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210609032554.2443675-1-ikjn@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This adds a reference to the dts of the Raspberry Pi 400,
so we don't need to maintain the content in arm64.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Link: https://lore.kernel.org/r/1622981777-5023-8-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
It would be helpful if mem_abort_decode() could decode the DFSC/IFSC, as
this can make it easier to identify common bugs (e.g. accesses which
trigger alignment faults) without having to manually decode the xFSC
value.
Decode the xFSC in mem_abort_decode().
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210608123742.11921-1-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
AM642-SK has no PCIe slot. Disable it here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210603142251.14563-6-kishon@ti.com
AM642 EVM has a x4 lane PCIe connector. Enable PCIe in RC mode here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210603142251.14563-4-kishon@ti.com
AM64 has one PCIe instance which can be configured in either
host mode (RC) or device mode (EP). Add PCIe DT node for host
mode and device mode here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210603142251.14563-3-kishon@ti.com
AM64 has one SERDES 10G instance. Add SERDES DT node for it.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210603142251.14563-2-kishon@ti.com
Commit 66db854b1f ("arm64: dts: ti: k3-j721e-common-proc-board:
Configure the PCIe instances") and
commit 02c35dca2b ("arm64: dts: ti: k3-j721e: Enable Super-Speed
support for USB0") added PHY DT nodes with node name as "link"
However nodes with #phy-cells should be named 'phy' as discussed in [1].
Re-name subnodes of serdes in J721E to 'phy'.
[1] -> http://lore.kernel.org/r/20200909203631.GA3026331@bogus
Fixes: 66db854b1f ("arm64: dts: ti: k3-j721e-common-proc-board: Configure the PCIe instances")
Fixes: 02c35dca2b ("arm64: dts: ti: k3-j721e: Enable Super-Speed support for USB0")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210603143427.28735-5-kishon@ti.com
Use external clock for all the SERDES used by PCIe controller. This will
make the same clock used by the local SERDES as well as the clock
provided to the PCIe connector.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210603143427.28735-4-kishon@ti.com
Add #clock-cells property to serdes DT node since the serdes is also now
modeled as a clock provider and include the input clocks "pll0_refclk"
and "pll1_refclk" which are parents to the clocks modeled by serdes.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210603143427.28735-3-kishon@ti.com
Rename the external refclk inputs to the SERDES from
dummy_cmn_refclk/dummy_cmn_refclk1 to cmn_refclk/cmn_refclk1
respectively. Also move the external refclk DT nodes outside the
cbass_main DT node. Since in j721e common processor board, only the
cmn_refclk1 is connected to 100MHz clock, fix the clock frequency.
Fixes: afd094ebe6 ("arm64: dts: ti: k3-j721e-main: Add WIZ and SERDES PHY nodes")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210603143427.28735-2-kishon@ti.com
SMCCC v1.2 requires that all SVE state be preserved over SMC calls which
introduces substantial overhead in the common case where there is no SVE
state in the registers. To avoid this SMCCC v1.3 introduces a flag which
allows the caller to say that there is no state that needs to be preserved
in the registers. Make use of this flag, setting it if the SMCCC version
indicates support for it and the TIF_ flags indicate that there is no live
SVE state in the registers, this avoids placing any constraints on when
SMCCC calls can be done or triggering extra saving and reloading of SVE
register state in the kernel.
This would be straightforward enough except for the rather entertaining
inline assembly we use to do SMCCC v1.1 calls to allow us to take advantage
of the limited number of registers it clobbers. Deal with this by having a
function which we call immediately before issuing the SMCCC call to make
our checks and set the flag. Using alternatives the overhead if SVE is
supported but not detected at runtime can be reduced to a single NOP.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210603184118.15090-1-broonie@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Enable support for audio-graph based sound card on Jetson Xavier NX.
Following I/O interfaces are enabled.
- I2S3 and I2S5
- DMIC1, DMIC2 and DMIC4
- DSPK1 and DSPK2
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This enables the adreno-specific SMMU path that sets HUPCF so
(user-managed) page faults don't wedge the GPU.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210326231303.3071950-2-eric@anholt.net
Signed-off-by: Will Deacon <will@kernel.org>
The ICSSGs on K3 J721E SoCs contain an MDIO controller that can
be used to control external PHYs associated with the Industrial
Ethernet peripherals within each ICSSG instance. The MDIO module
used within the ICSSG is similar to the MDIO Controller used
in TI Davinci SoCs. A bus frequency of 1 MHz is chosen for the
MDIO operations.
The nodes are added and enabled in the common k3-j721e-main.dtsi
file by default, and disabled in the existing J721E board dts
file. These nodes need pinctrl lines, and so should be enabled
only on boards where they are actually wired and pinned out for
ICSSG Ethernet. Any new board dts file should disable these if
they are not sure.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210601150032.11432-3-s-anna@ti.com
The ICSSGs on K3 AM65x SoCs contain an MDIO controller that can
be used to control external PHYs associated with the Industrial
Ethernet peripherals within each ICSSG instance. The MDIO module
used within the ICSSG is similar to the MDIO Controller used
in TI Davinci SoCs. A bus frequency of 1 MHz is chosen for the
MDIO operations.
The nodes are added and enabled in the common k3-am65-main.dtsi
file by default, and disabled in the existing AM65 board dts
files. These nodes need pinctrl lines, and so should be enabled
only on boards where they are actually wired and pinned out for
ICSSG Ethernet. Any new board dts file should disable these if
they are not sure.
Signed-off-by: Roger Quadros <rogerq@ti.com>
[s-anna@ti.com: move the disabled status to board dts files]
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210601150032.11432-2-s-anna@ti.com
UHS-I speed modes are supported in AM65 S.R. 2.0 SoC[1].
Add support by removing the no-1-8-v tag and including the voltage
regulator device tree nodes for power cycling.
However, the 4 bit interface of AM65 SR 1.0 cannot be supported at 3.3 V or
1.8 V because of erratas i2025 and i2026 [2]. As the SD card is the primary
boot mode for development usecases, continue to enable SD card and disable
UHS-I modes in it to minimize any ageing issues happening because of
erratas.
k3-am6528-iot2050-basic and k3-am6548-iot2050-advanced boards use S.R. 1.0
version of AM65 SoC. Therefore, add no-1-8-v in sdhci1 device tree node of
the common iot2050 device tree file.
[1] - https://www.ti.com/lit/ug/spruid7e/spruid7e.pdf, section 12.3.6.1.1
[2] - https://www.ti.com/lit/er/sprz452e/sprz452e.pdf
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Acked-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210529033749.6250-1-a-govindraju@ti.com
The low-level idle code in arch_cpu_idle() and its callees runs at a
time where where portions of the kernel environment aren't available.
For example, RCU may not be watching, and lockdep state may be
out-of-sync with the hardware. Due to this, it is not sound to
instrument this code.
We generally avoid instrumentation by marking the entry functions as
`noinstr`, but currently this doesn't inhibit KCOV instrumentation.
Prevent this by factoring these functions into a new idle.c so that we
can disable KCOV for the entire compilation unit, as is done for the
core idle code in kernel/sched/idle.c.
We'd like to keep instrumentation of the rest of process.c, and for the
existing code in cpuidle.c, so a new compilation unit is preferable. The
arch_cpu_idle_dead() function in process.c is a cpu hotplug function
that is safe to instrument, so it is left as-is in process.c.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-21-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
The code in entry-common.c runs at exception entry and return
boundaries, where portions of the kernel environment aren't available.
For example, RCU may not be watching, and lockdep state may be
out-of-sync with the hardware. Due to this, it is not sound to
instrument this code.
We generally avoid instrumentation by marking the entry functions as
`noinstr`, but currently this doesn't inhibit KCOV instrumentation.
Prevent this by disabling KCOV for the entire compilation unit.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-20-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Now that we only call arm64_enter_nmi() and arm64_exit_nmi() from within
entry-common.c, let's make these static to ensure this remains the case.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-19-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
We'd like to keep all the entry sequencing in entry-common.c, as this
will allow us to ensure this is consistent, and free from any unsound
instrumentation.
Currently __sdei_handler() performs the NMI entry/exit sequences in
sdei.c. Let's split the low-level entry sequence from the event
handling, moving the former to entry-common.c and keeping the latter in
sdei.c. The event handling function is renamed to do_sdei_event(),
matching the do_${FOO}() pattern used for other exception handlers.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-18-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
We'd like to keep all the entry sequencing in entry-common.c, as this
will allow us to ensure this is consistent, and free from any unsound
instrumentation.
Currently handle_bad_stack() performs the NMI entry sequence in traps.c.
Let's split the low-level entry sequence from the reporting, moving the
former to entry-common.c and keeping the latter in traps.c. To make it
clear that reporting function never returns, it is renamed to
panic_bad_stack().
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-17-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
An unexpected synchronous exception from EL1h could happen at any time,
and for robustness we should treat this as an NMI, making minimal
assumptions about the context the exception was taken from.
Currently el1_inv() assumes we can use enter_from_kernel_mode(), and
also assumes that we should inherit the original DAIF value. Neither of
these are desireable when we take an unexpected exception. Further,
after el1_inv() calls __panic_unhandled(), the remainder of the function
is unreachable, and therefore superfluous.
Let's address this and simplify things by having el1h_64_sync_handler()
call __panic_unhandled() directly, without any of the redundant logic.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Reported-by: Joey Gouly <joey.gouly@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-16-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
We have 16 architectural exception vectors, and depending on kernel
configuration we handle 8 or 12 of these with C code, with the remaining
8 or 4 of these handled as special cases in the entry assembly.
It would be nicer if the entry assembly were uniform for all exceptions,
and we deferred any specific handling of the exceptions to C code. This
way the entry assembly can be more easily templated without ifdeffery or
special cases, and it's easier to modify the handling of these cases in
future (e.g. to dump additional registers other context).
This patch reworks the entry code so that we always have a C handler for
every architectural exception vector, with the entry assembly being
completely uniform. We now have to handle exceptions from EL1t and EL1h,
and also have to handle exceptions from AArch32 even when the kernel is
built without CONFIG_COMPAT. To make this clear and to simplify
templating, we rename the top-level exception handlers with a consistent
naming scheme:
asm: <el+sp>_<regsize>_<type>
c: <el+sp>_<regsize>_<type>_handler
.. where:
<el+sp> is `el1t`, `el1h`, or `el0t`
<regsize> is `64` or `32`
<type> is `sync`, `irq`, `fiq`, or `error`
... e.g.
asm: el1h_64_sync
c: el1h_64_sync_handler
... with lower-level handlers simply using "el1" and "compat" as today.
For unexpected exceptions, this information is passed to
__panic_unhandled(), so it can report the specific vector an unexpected
exception was taken from, e.g.
| Unhandled 64-bit el1t sync exception
For vectors we never expect to enter legitimately, the C code is
generated using a macro to avoid code duplication. The exceptions are
handled via __panic_unhandled(), replacing bad_mode() (which is
removed).
The `kernel_ventry` and `entry_handler` assembly macros are updated to
handle the new naming scheme. In theory it should be possible to
generate the entry functions at the same time as the vectors using a
single table, but this will require reworking the linker script to split
the two into separate sections, so for now we have separate tables.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-15-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Now that the majority of the exception triage logic has been converted
to C, the entry assembly functions all have a uniform structure.
Let's generate them all with an assembly macro to reduce the amount of
code and to ensure they all remain in sync if we make changes in future.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-14-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Our use of bad_mode() has a few rough edges:
* AArch64 doesn't use the term "mode", and refers to "Execution
states", "Exception levels", and "Selected stack pointer".
* We log the exception type (SYNC/IRQ/FIQ/SError), but not the actual
"mode" (though this can be decoded from the SPSR value).
* We use bad_mode() as a second-level handler for unexpected synchronous
exceptions, where the "mode" is legitimate, but the specific exception
is not.
* We dump the ESR value, but call this "code", and so it's not clear to
all readers that this is the ESR.
... and all of this can be somewhat opaque to those who aren't extremely
familiar with the code.
Let's make this a bit clearer by having bad_mode() log "Unhandled
${TYPE} exception" rather than "Bad mode in ${TYPE} handler", using
"ESR" rather than "code", and having the final panic() log "Unhandled
exception" rather than "Bad mode".
In future we'd like to log the specific architectural vector rather than
just the type of exception, so we also split the core of bad_mode() out
into a helper called __panic_unhandled(), which takes the vector as a
string argument.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-13-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
In subsequent patches we'll rework the way bad_mode() is called by
exception entry code. In preparation for this, let's move bad_mode()
itself into entry-common.c.
Let's also mark it as noinstr (e.g. to prevent it being kprobed), and
let's also make the `handler` array a local variable, as this is only
use by bad_mode(), and will be removed entirely in a subsequent patch.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-12-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Following the example of ret_to_user, let's consolidate all the EL1
return paths with a ret_to_kernel helper, rather than each entry point
having its own copy of the return code.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-11-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
In subsequent patches we'll rename the entry handlers based on their
original EL, register width, and exception class. To do so, we need to
make all 3 mandatory arguments to the `kernel_ventry` macro, and
distinguish EL1h from EL1t.
In preparation for this, let's make the current set of arguments
mandatory, and move the `regsize` column before the branch label suffix,
making the vectors easier to read column-wise.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-10-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
In entry.S we have two comments which distinguish EL0 and EL1 exception
handlers, but the code isn't actually laid out to match, and there are a
few other inconsistencies that would be good to clear up.
This patch organizes the entry handers consistently:
* The handlers are laid out in order of the vectors, to make them easier
to navigate.
* The inconsistently-applied alignment is removed
* The handlers are consistently marked with SYM_CODE_START_LOCAL()
rather than SYM_CODE_START_LOCAL_NOALIGN(), giving them the same
default alignment as other assembly code snippets.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-9-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
For various reasons we'd like to convert the bulk of arm64's exception
triage logic to C. As a step towards that, this patch converts the EL1
and EL0 IRQ+FIQ triage logic to C.
Separate C functions are added for the native and compat cases so that
in subsequent patches we can handle native/compat differences in C.
Since the triage functions can now call arm64_apply_bp_hardening()
directly, the do_el0_irq_bp_hardening() wrapper function is removed.
Since the user_exit_irqoff macro is now unused, it is removed. The
user_enter_irqoff macro is still used by the ret_to_user code, and
cannot be removed at this time.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-8-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
When handling IRQ/FIQ exceptions the entry assembly may transition from
a task's stack to a CPU's IRQ stack (and IRQ shadow call stack).
In subsequent patches we want to migrate the IRQ/FIQ triage logic to C,
and as we want to perform some actions on the task stack (e.g. EL1
preemption), we need to switch stacks within the C handler. So that we
can do so, this patch adds a helper to call a function on a CPU's IRQ
stack (and shadow stack as appropriate).
Subsequent patches will make use of the new helper function.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-7-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Currently portions of our preempt logic are written in C while other
parts are written in assembly. Let's clean this up a little bit by
moving the NMI preempt checks to C. For now, the preempt count (and
need_resched) checking is left in assembly, and will be converted
with the body of the IRQ handler in subsequent patches.
Other than the increased lockdep coverage there should be no functional
change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-6-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Subsequent patches will pull more of the IRQ entry handling into C. To
keep this in one place, let's move arm64_preempt_schedule_irq() into
entry-common.c along with the other entry management functions.
We no longer need to include <linux/lockdep.h> in process.c, so the
include directive is removed.
There should be no functional change as a result of this patch.
Reviewed-by Joey Gouly <joey.gouly@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-5-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
For various reasons we'd like to convert the bulk of arm64's exception
triage logic to C. As a step towards that, this patch converts the EL1
and EL0 SError triage logic to C.
Separate C functions are added for the native and compat cases so that
in subsequent patches we can handle native/compat differences in C.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-4-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
For non-fatal exceptions taken from EL0, we expect that at some point
during exception handling it is possible to return to a regular process
context with all exceptions unmasked (e.g. as we do in
do_notify_resume()), and we generally aim to unmask exceptions wherever
possible.
While handling SError and debug exceptions from EL0, we need to leave
some exceptions masked during handling. Handling SError requires us to
mask SError (which also requires masking IRQ+FIQ), and handing debug
exceptions requires us to mask debug (which also requires masking
SError+IRQ+FIQ).
Once do_serror() or do_debug_exception() has returned, we no longer need
to mask exceptions, and can unmask them all, which is what we did prior
to commit:
9034f62515 ("arm64: Do not enable IRQs for ct_user_exit")
... where we had to mask IRQs as for context_tracking_user_exit()
expected IRQs to be masked.
Since then, we realised that our context tracking wasn't entirely
correct, and reworked the entry code to fix this. As of commit:
23529049c6 ("arm64: entry: fix non-NMI user<->kernel transitions")
... we replaced the call to context_tracking_user_exit() with a call to
user_exit_irqoff() as part of enter_from_user_mode(), which occurs
earlier, before we run the body of the handler and unmask exceptions in
DAIF.
When we return to userspace, we go via ret_to_user(), which masks
exceptions in DAIF prior to calling user_enter_irqoff() as part of
exit_to_user_mode().
Thus, there's no longer a reason to leave IRQs or FIQs masked at the end
of the EL0 debug or error handlers, as neither the user exit context
tracking nor the user entry context tracking requires this. Let's bring
these into line with other EL0 exception handlers and ensure that IRQ
and FIQ are unmasked in DAIF at some point during the handler.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-3-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Upon taking an exception, the CPU sets all the DAIF bits. We never
clear any of these bits prior to calling bad_mode(), and bad_mode()
itself never clears any of these bits, so there's no need to call
local_daif_mask().
This patch removes the redundant call.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210607094624.34689-2-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
"make dtbs_check":
arm64/boot/dts/renesas/r8a779a0-falcon.dt.yaml: interrupt-controller@f1000000: 'power-domains' does not match any of the regexes: '^(msi-controller|gic-its|interrupt-controller)@[0-9a-f]+$', '^gic-its@', '^interrupt-controller@[0-9a-f]+$', 'pinctrl-[0-9]+'
From schema: Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.yaml
Remove the "power-domains" property, as the GIC on R-Car V3U is
always-on, and not part of a clock domain.
Fixes: 834c310f54 ("arm64: dts: renesas: Add Renesas R8A779A0 SoC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/a9ae5cbc7c586bf2c6b18ddc665ad7051bd1d206.1622560236.git.geert+renesas@glider.be
A set of fixes that have been coming in over the last few weeks, the
usual mix of fixes:
- DT fixups for TI K3
- SATA drive detection fix for TI DRA7
- Power management fixes and a few build warning removals for OMAP
- OP-TEE fix to use standard API for UUID exporting
- DT fixes for a handful of i.MX boards
... plus a few other smaller items
-----BEGIN PGP SIGNATURE-----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=TbGI
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-fixes-v5.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A set of fixes that have been coming in over the last few weeks, the
usual mix of fixes:
- DT fixups for TI K3
- SATA drive detection fix for TI DRA7
- Power management fixes and a few build warning removals for OMAP
- OP-TEE fix to use standard API for UUID exporting
- DT fixes for a handful of i.MX boards
And a few other smaller items"
* tag 'arm-soc-fixes-v5.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (29 commits)
arm64: meson: select COMMON_CLK
soc: amlogic: meson-clk-measure: remove redundant dev_err call in meson_msr_probe()
ARM: OMAP1: ams-delta: remove unused function ams_delta_camera_power
bus: ti-sysc: Fix flakey idling of uarts and stop using swsup_sidle_act
ARM: dts: imx: emcon-avari: Fix nxp,pca8574 #gpio-cells
ARM: dts: imx7d-pico: Fix the 'tuning-step' property
ARM: dts: imx7d-meerkat96: Fix the 'tuning-step' property
arm64: dts: freescale: sl28: var1: fix RGMII clock and voltage
arm64: dts: freescale: sl28: var4: fix RGMII clock and voltage
ARM: imx: pm-imx27: Include "common.h"
arm64: dts: zii-ultra: fix 12V_MAIN voltage
arm64: dts: zii-ultra: remove second GEN_3V3 regulator instance
arm64: dts: ls1028a: fix memory node
bus: ti-sysc: Fix am335x resume hang for usb otg module
ARM: OMAP2+: Fix build warning when mmc_omap is not built
ARM: OMAP1: isp1301-omap: Add missing gpiod_add_lookup_table function
ARM: OMAP1: Fix use of possibly uninitialized irq variable
optee: use export_uuid() to copy client UUID
arm64: dts: ti: k3*: Introduce reg definition for interrupt routers
arm64: dts: ti: k3-am65|j721e|am64: Map the dma / navigator subsystem via explicit ranges
...
MMIO block mapping support from Keqian Zhu, allowing larger
(and lazy) mappings for devices assigned to guests.
* kvm-arm64/mmu/MMIO-block-mapping:
KVM: arm64: Try stage2 block mapping for host device MMIO
KVM: arm64: Remove the creation time's mapping of MMIO regions
Microsoft Surface Duo is based on SM8150 chipset. This new Device Tree
is a copy of sm8150-mtp with a the addition of the volume up key and
relevant i2c nodes.
Signed-off-by: Felipe Balbi <felipe.balbi@microsoft.com>
Link: https://lore.kernel.org/r/20210603122923.1919624-1-balbi@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Some SC7180 based boards do not have external pull-up for cd-gpio.
Set this pin to internal pull-up for sleep config to avoid frequent
regulator toggle events.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sujit Kautkar <sujitka@chromium.org>
Link: https://lore.kernel.org/r/20210602121313.v3.2.I52f30ddfe62041b7e6c3c362f0ad8f695ac28224@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Samsung Galaxy A3/A5 both have a Samsung S3FWRN5 NFC chip that
works quite well with the s3fwrn5 driver in the Linux NFC subsystem.
The clock setup for the NFC chip is a bit special (although this
seems to be a common approach used for Qualcomm devices with NFC):
The NFC chip has an output GPIO that is asserted whenever the clock
is needed to function properly. On the A3/A5 this is wired up to
PM8916 GPIO2, which is then configured with a special function
(NFC_CLK_REQ or BB_CLK2_REQ).
Enabling the rpmcc RPM_SMD_BB_CLK2_PIN clock will then instruct
PM8916 to automatically enable the clock whenever the NFC chip
requests it. The advantage is that the clock is only enabled when
needed and we don't need to manage it ourselves from the NFC driver.
Note that for some reason Samsung decided to connect the I2C pins
to GPIOs where no hardware I2C bus is available, so we need to
fall back to software bit-banging with i2c-gpio.
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210604172742.10593-5-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Samsung Galaxy A3/A5 use a Richtek RT5033 PMIC as battery
fuel gauge, charger, flash LED and for some regulators. For now,
only add the fuel gauge/battery device to the device tree,
so we can check the remaining battery percentage.
The other RT5033 drivers need some more work first before
they can be used properly.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210604172742.10593-4-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
On the Samsung Galaxy A5 the touch key is supplied by a single fixed
regulator (enabled via GPIO 97) that supplies both MCU and LED.
Add it to the device tree.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210604172742.10593-3-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The touch key MCU and LED is supplied by two separate fixed regulators
that can be enabled through GPIO 86 and 60. Add them to the device tree.
Signed-off-by: Michael Srba <Michael.Srba@seznam.cz>
[stephan: extend commit message]
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210604172742.10593-2-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Samsung Galaxy A3/A5 both have two capacitive touch keys,
connected to an ABOV MCU. It implements the same interface as
implemented by the tm2-touchkey driver and works just fine with
the coreriver,tc360-touchkey compatible. It's probably actually some
Samsung-specific interface that they implement with different MCUs.
Note that for some reason Samsung decided to connect this to GPIOs
where no hardware I2C bus is available, so we need to fall back
to software bit-banging using i2c-gpio.
The vdd/vcc-supply is board-specific and will be added separately
for a3u/a5u.
Co-developed-by: Michael Srba <Michael.Srba@seznam.cz>
Signed-off-by: Michael Srba <Michael.Srba@seznam.cz>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210604172742.10593-1-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add a thermal zone for the pm6150 on-die temperature. The system should
try to shut down orderly when the temperature reaches the critical trip
point at 115°C, otherwise the PMIC will perform a HW power off at 145°C.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20210603081215.v2.1.Id4510e9e4baaa3f6c9fdd5cdf4d8606e63c262e3@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
These minor fixes include:
* Fixups for device tree discovered during yaml conversion
* Fixups for missing dma-coherent property in j7200
* Removal of camera sensor node from am65 evm dts to overlay
as camera sensor boards are variable.
-----BEGIN PGP SIGNATURE-----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=veTm
-----END PGP SIGNATURE-----
Merge tag 'ti-k3-dt-fixes-for-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/nmenon/linux into arm/fixes
Devicetree fixes for TI K3 platforms for v5.13 merge window:
These minor fixes include:
* Fixups for device tree discovered during yaml conversion
* Fixups for missing dma-coherent property in j7200
* Removal of camera sensor node from am65 evm dts to overlay
as camera sensor boards are variable.
* tag 'ti-k3-dt-fixes-for-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/nmenon/linux:
arm64: dts: ti: k3*: Introduce reg definition for interrupt routers
arm64: dts: ti: k3-am65|j721e|am64: Map the dma / navigator subsystem via explicit ranges
arm64: dts: ti: k3-*: Rename the TI-SCI node
arm64: dts: ti: k3-am65-wakeup: Drop un-necessary properties from dmsc node
arm64: dts: ti: k3-am65-wakeup: Add debug region to TI-SCI node
arm64: dts: ti: k3-*: Rename the TI-SCI clocks node name
arm64: dts: ti: j7200-main: Mark Main NAVSS as dma-coherent
arm64: dts: ti: k3-am654-base-board: remove ov5640
Link: https://lore.kernel.org/r/20210518115634.467vgpbzplal5kou@obituary
Signed-off-by: Olof Johansson <olof@lixom.net>
- Fix missing-prototypes warning of 'imx27_pm_init' in i.MX27 platform
pm code.
- A couple of patches from Fabio Estevam to fix 'tuning-step' property
in imx7d-meerkat96 and imx7d-pico DT.
- Fix '#gpio-cells' of nxp,pca8574 device in imx6qdl-emcon-avari DT.
- A couple of patches from Lucas Stach to fix regulator and voltage for
imx8mq-zii-ultra board.
- Add missing regulators for imx6q-dhcom to avoid possible instability
issues.
- Fix memory-controller settings for fsl-ls1028a DT.
- Fix RGMII clock and voltage for a couple of fsl-ls1028a-kontron-sl28
boards.
- Fix RGMII connection to QCA8334 switch for imx6dl-yapp4 board.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAmCu8p4UHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM7k+Qf9Ek/atJBjaaVzhbGFQ8HRnDOk4U5J
dR0GbXKSN1zXjDLSBOBRyNcVn2T6lp4LwwYoleC2qG6MNoe6+y7fk1oRdvjkGjRO
ZYfZT/JJl187IN6JsxR8VhRmmcI5/C3bihMbpKoLdHcPGbwC4relfSy99Io94Xfk
CVn3PTxBA4KfoDq/+EiA9HkQ/HwQh/y7KD5yVd6OtLkt9awT1hYW1ttVefp95nAK
5+zTm0Z14U8aGm+wo8jywvSyeXiuMeWDUrweo05XcaHWfcv3T0Wni7tgS2pluxqa
lCMsNQBsZDTk6fUWxqPjjAEl6ks8N1H9L7YIGpq1dOCSYFUqI3jCmkhrFQ==
=5vQk
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.13:
- Fix missing-prototypes warning of 'imx27_pm_init' in i.MX27 platform
pm code.
- A couple of patches from Fabio Estevam to fix 'tuning-step' property
in imx7d-meerkat96 and imx7d-pico DT.
- Fix '#gpio-cells' of nxp,pca8574 device in imx6qdl-emcon-avari DT.
- A couple of patches from Lucas Stach to fix regulator and voltage for
imx8mq-zii-ultra board.
- Add missing regulators for imx6q-dhcom to avoid possible instability
issues.
- Fix memory-controller settings for fsl-ls1028a DT.
- Fix RGMII clock and voltage for a couple of fsl-ls1028a-kontron-sl28
boards.
- Fix RGMII connection to QCA8334 switch for imx6dl-yapp4 board.
* tag 'imx-fixes-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx: emcon-avari: Fix nxp,pca8574 #gpio-cells
ARM: dts: imx7d-pico: Fix the 'tuning-step' property
ARM: dts: imx7d-meerkat96: Fix the 'tuning-step' property
arm64: dts: freescale: sl28: var1: fix RGMII clock and voltage
arm64: dts: freescale: sl28: var4: fix RGMII clock and voltage
ARM: imx: pm-imx27: Include "common.h"
arm64: dts: zii-ultra: fix 12V_MAIN voltage
arm64: dts: zii-ultra: remove second GEN_3V3 regulator instance
arm64: dts: ls1028a: fix memory node
ARM: dts: imx6q-dhcom: Add PU,VDD1P1,VDD2P5 regulators
ARM: dts: imx6dl-yapp4: Fix RGMII connection to QCA8334 switch
Link: https://lore.kernel.org/r/20210527011758.GD8194@dragon
Signed-off-by: Olof Johansson <olof@lixom.net>
Currently, on an anonymous page fault, the kernel allocates a zeroed
page and maps it in user space. If the mapping is tagged (PROT_MTE),
set_pte_at() additionally clears the tags. It is, however, more
efficient to clear the tags at the same time as zeroing the data on
allocation. To avoid clearing the tags on any page (which may not be
mapped as tagged), only do this if the vma flags contain VM_MTE. This
requires introducing a new GFP flag that is used to determine whether
to clear the tags.
The DC GZVA instruction with a 0 top byte (and 0 tag) requires
top-byte-ignore. Set the TCR_EL1.{TBI1,TBID1} bits irrespective of
whether KASAN_HW is enabled.
Signed-off-by: Peter Collingbourne <pcc@google.com>
Co-developed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://linux-review.googlesource.com/id/Id46dc94e30fe11474f7e54f5d65e7658dbdddb26
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com>
Link: https://lore.kernel.org/r/20210602235230.3928842-4-pcc@google.com
Signed-off-by: Will Deacon <will@kernel.org>
In an upcoming change we would like to add a flag to
GFP_HIGHUSER_MOVABLE so that it would no longer be an OR
of GFP_HIGHUSER and __GFP_MOVABLE. This poses a problem for
alloc_zeroed_user_highpage_movable() which passes __GFP_MOVABLE
into an arch-specific __alloc_zeroed_user_highpage() hook which ORs
in GFP_HIGHUSER.
Since __alloc_zeroed_user_highpage() is only ever called from
alloc_zeroed_user_highpage_movable(), we can remove one level
of indirection here. Remove __alloc_zeroed_user_highpage(),
make alloc_zeroed_user_highpage_movable() the hook, and use
GFP_HIGHUSER_MOVABLE in the hook implementations so that they will
pick up the new flag that we are going to add.
Signed-off-by: Peter Collingbourne <pcc@google.com>
Link: https://linux-review.googlesource.com/id/Ic6361c657b2cdcd896adbe0cf7cb5a7fbb1ed7bf
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20210602235230.3928842-2-pcc@google.com
Signed-off-by: Will Deacon <will@kernel.org>
We alread have is_el1_instruction_abort(), add is_el1_data_abort()
helper and use it.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20210603120239.169018-1-wangkefeng.wang@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
Kprobes has a counter 'nmissed', that is used to count the number of
times a probe handler was not called. This generally happens when we hit
a kprobe while handling another kprobe.
However, if one of the probe handlers causes a fault, we are currently
incrementing 'nmissed'. The comment in fault handler indicates that this
can be used to account faults taken by the probe handlers. But, this has
never been the intention as is evident from the comment above 'nmissed'
in 'struct kprobe':
/*count the number of times this probe was temporarily disarmed */
unsigned long nmissed;
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Link: https://lkml.kernel.org/r/20210601120150.672652-1-naveen.n.rao@linux.vnet.ibm.com
The Rockchip RK3308 features an integrated USB 2.0 phy, an USB OTG
controller and OHCI/EHCI interfaces.
This patch adds all of those to the RK3308 dtsi and thereby enables USB
support on the RK3308.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210601164800.7670-6-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The pattern: "^(|usb-|usb2-|usb3-|pci-|pcie-|sata-)phy(@[0-9a-f,]+)*$"
in phy-provider.yaml has required "#phy-cells" for phy nodes.
The "phy-cells" in rockchip-inno-usb2 nodes are located in subnodes.
Rename the nodename to pattern "usb2phy@[0-9a-f]+$" to prevent
notifications.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/schemas/
phy/phy-provider.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210601164800.7670-5-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Armv8.7 has introduced BUS_SLOTS and BUS_WIDTH in PMMIR_EL1 register,
add two entries in caps for bus_slots and bus_width under sysfs. It
will return the true slots and width if the information is available,
otherwise it will return 0.
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Link: https://lore.kernel.org/r/1622704502-63951-1-git-send-email-zhangshaokun@hisilicon.com
Signed-off-by: Will Deacon <will@kernel.org>
Add the new rk817 codec driver to the Odroid Go Advance.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Tested-by: Maciej Matuszczyk <maccraft123mc@gmail.com>
Link: https://lore.kernel.org/r/20210519203754.27184-5-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
To make future archaeology easier, let's have the string routine comment
blocks encode the specific upstream commit ID they were imported from.
These are the same commit IDs as listed in the commits importing the
code, expanded to 16 characters. Note that the routines have different
commit IDs, each reprsenting the latest upstream commit which changed
the particular routine.
At the same time, let's consistently include 2021 in the copyright
dates.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210602151358.35571-1-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Enable the Exynos UFS controller and PHY configs. They need to be
buildin to ensure UFS devices gets detected on exynos7 and its
variant boards.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Link: https://lore.kernel.org/r/20210531170057.7730-1-alim.akhtar@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
We don't need to register smi_common as syscon. Also add required
property power-domains for this node.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20210601040014.2970805-1-hsinyi@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Back in 9730348075 ("arm64: Increase the max granular size"),
ARCH_DMA_MINALIGN was effectively increased to 128 bytes thanks to an
increase in L1_CACHE_BYTES due to an unsubstantiated performance claim
on the now obsolete ThunderX-1. Although this was reverted in
d93277b983, ARCH_DMA_MINALIGN was kept at 128 bytes by ebc7e21e0f
("arm64: Increase ARCH_DMA_MINALIGN to 128").
During discussion of the original patch, it was reported that the change
also prevented a warning during boot on (again, now obsolete) Qualcomm
server hardware where the cache writeback granule was larger than 64
bytes. The reason for this warning was because non-coherent DMA could
lead to data corruption due to unexpected writeback from the CPU where a
cacheline is shared with other allocations.
Since then, systems have appeared with larger cachelines still, and so
commit 8f5c9037a5 ("arm64/mm: Correct the cache line size warning with
non coherent device") reworked the warning so that it only appears on
systems where non-coherent DMA is actually required and taints the
kernel with TAINT_CPU_OUT_OF_SPEC. We are not aware of any systems, even
including the aforementioned obsolete machines, which have a CWG larger
than 64 bytes and require non-coherent DMA.
More recently, it has been reported that a ARCH_DMA_MINALIGN of 128
bytes wastes considerable memory (~6% immediately after boot on one
system).
Reduce ARCH_DMA_MINALIGN to 64 bytes and allow the warning/taint to
indicate if there are machines that unknowingly rely on this.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/linux-arm-kernel/1442944788-17254-1-git-send-email-rric@kernel.org/
Link: https://lore.kernel.org/linux-arm-kernel/CAOZdJXUiRMAguDV+HEJqPg57MyBNqEcTyaH+ya=U93NHb-pdJA@mail.gmail.com/
Link: https://lore.kernel.org/linux-arm-kernel/20190614131141.4428-1-msys.mizuma@gmail.com/
Link: https://lore.kernel.org/r/20210517074332.28280-1-vincent.whitchurch@axis.com
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210527124356.22367-1-will@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
The Normal-WT memory type is unused, so remove it and reclaim a MAIR.
Cc: Christoph Hellwig <hch@lst.de>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20210527110319.22157-4-will@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
The only user we have of Normal Write-Through memory is in the ACPI code
when mapping memory regions advertised as EFI_MEMORY_WT. Since most (all?)
CPUs treat write-through as non-cacheable under the hood, don't bother
with the extra memory type here and just treat EFI_MEMORY_WT the same way
as EFI_MEMORY_WC by mapping it to the Normal-NC memory type instead and
emitting a warning if we have failed to find an alternative EFI memory
type.
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Christoph Hellwig <hch@lst.de>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210527110319.22157-3-will@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Now that we're always using STTR variants rather than abstracting two
different addressing modes, the user_ldst macro here is frankly more
obfuscating than helpful. Rewrite __arch_clear_user() with regular
USER() annotations so that it's clearer what's going on, and take the
opportunity to minimise the branchiness in the most common paths, while
also allowing the exception fixup to return an accurate result.
Apparently some folks examine large reads from /dev/zero closely enough
to notice the loop being hot, so align it per the other critical loops
(presumably around a typical instruction fetch granularity).
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/1cbd78b12c076a8ad4656a345811cfb9425df0b3.1622128527.git.robin.murphy@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Although we implement our own assembly version of memchr(), it turns
out to be barely any better than what GCC can generate for the generic
C version (and would go wrong if the size_t argument were ever large
enough to be interpreted as negative). Unfortunately we can't import the
tuned implementation from the Arm optimized-routines library, since that
has some Advanced SIMD parts which are not really viable for general
kernel library code. What we can do, however, is pep things up with some
relatively straightforward word-at-a-time logic for larger calls.
Adding some timing to optimized-routines' memchr() test for a simple
benchmark, overall this version comes in around half as fast as the SIMD
code, but still nearly 4x faster than our existing implementation.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/58471b42f9287e039dafa9e5e7035077152438fd.1622128527.git.robin.murphy@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Import the latest implementation of memcpy(), based on the
upstream code of string/aarch64/memcpy.S at commit afd6244 from
https://github.com/ARM-software/optimized-routines, and subsuming
memmove() in the process.
Note that for simplicity Arm have chosen to contribute this code
to Linux under GPLv2 rather than the original MIT license.
Note also that the needs of the usercopy routines vs. regular memcpy()
have now diverged so far that we abandon the shared template idea
and the damage which that incurred to the tuning of LDP/STP loops.
We'll be back to tackle those routines separately in future.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/3c953af43506581b2422f61952261e76949ba711.1622128527.git.robin.murphy@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Import the latest version of the former Cortex Strings - now
Arm Optimized Routines - strncmp function based on the upstream
code of string/aarch64/strncmp.S at commit e823e3a from
https://github.com/ARM-software/optimized-routines
Note that for simplicity Arm have chosen to contribute this code
to Linux under GPLv2 rather than the original MIT license.
Signed-off-by: Sam Tebbs <sam.tebbs@arm.com>
[ rm: update attribution and commit message ]
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/26110bee02ad360596c9a7536af7eaaf6890d0e8.1622128527.git.robin.murphy@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Import an updated version of the former Cortex Strings - now Arm
Optimized Routines - strcmp function. The latest version introduces
Advanced SIMD usage which rules it out for our purposes, but we can
still pick an intermediate improvement from the previous version,
namely string/aarch64/strlen.S at commit 98e4d6a from
https://github.com/ARM-software/optimized-routines
Note that for simplicity Arm have chosen to contribute this code
to Linux under GPLv2 rather than the original MIT license.
Signed-off-by: Sam Tebbs <sam.tebbs@arm.com>
[ rm: update attribution and commit message ]
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/32e3489398a24b23ae6e996935ac4818f8fd9dfd.1622128527.git.robin.murphy@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Import the latest version of the former Cortex Strings - now
Arm Optimized Routines - strcmp function based on the upstream
code of string/aarch64/strcmp.S at commit afd6244 from
https://github.com/ARM-software/optimized-routines
Note that for simplicity Arm have chosen to contribute this code
to Linux under GPLv2 rather than the original MIT license.
Signed-off-by: Sam Tebbs <sam.tebbs@arm.com>
[ rm: update attribution and commit message ]
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/0fe90c90b96b569fbdfd46e47bd1298abb02079e.1622128527.git.robin.murphy@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Import the latest version of the former Cortex Strings - now
Arm Optimized Routines - memcmp function based on the upstream
code of string/aarch64/memcmp.S at commit e823e3a from
https://github.com/ARM-software/optimized-routines
Note that for simplicity Arm have chosen to contribute this code
to Linux under GPLv2 rather than the original MIT license.
Signed-off-by: Sam Tebbs <sam.tebbs@arm.com>
[ rm: update attribution and commit message ]
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/2889de2d41054f3f508fb3addad784a3606ef383.1622128527.git.robin.murphy@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Adds label for MI2S secondary block to allow follower projects to override
for the four speaker support which uses I2S SD1 line on gpio52 pin.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
Link: https://lore.kernel.org/r/20210601022117.4071117-1-judyhsiao@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The reason for kprobe::fault_handler(), as given by their comment:
* We come here because instructions in the pre/post
* handler caused the page_fault, this could happen
* if handler tries to access user space by
* copy_from_user(), get_user() etc. Let the
* user-specified handler try to fix it first.
Is just plain bad. Those other handlers are ran from non-preemptible
context and had better use _nofault() functions. Also, there is no
upstream usage of this.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Link: https://lore.kernel.org/r/20210525073213.561116662@infradead.org
Use sysfs_emit instead of snprintf to avoid buf overrun,because in
sysfs_emit it strictly checks whether buf is null or buf whether
pagesize aligned, otherwise it returns an error.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Link: https://lore.kernel.org/r/1621497585-30887-1-git-send-email-tiantao6@hisilicon.com
Signed-off-by: Will Deacon <will@kernel.org>
The MMIO region of a device maybe huge (GB level), try to use
block mapping in stage2 to speedup both map and unmap.
Compared to normal memory mapping, we should consider two more
points when try block mapping for MMIO region:
1. For normal memory mapping, the PA(host physical address) and
HVA have same alignment within PUD_SIZE or PMD_SIZE when we use
the HVA to request hugepage, so we don't need to consider PA
alignment when verifing block mapping. But for device memory
mapping, the PA and HVA may have different alignment.
2. For normal memory mapping, we are sure hugepage size properly
fit into vma, so we don't check whether the mapping size exceeds
the boundary of vma. But for device memory mapping, we should pay
attention to this.
This adds get_vma_page_shift() to get page shift for both normal
memory and device MMIO region, and check these two points when
selecting block mapping size for MMIO region.
Signed-off-by: Keqian Zhu <zhukeqian1@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210507110322.23348-3-zhukeqian1@huawei.com
The MMIO regions may be unmapped for many reasons and can be remapped
by stage2 fault path. Map MMIO regions at creation time becomes a
minor optimization and makes these two mapping path hard to sync.
Remove the mapping code while keep the useful sanity check.
Signed-off-by: Keqian Zhu <zhukeqian1@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210507110322.23348-2-zhukeqian1@huawei.com
In order to deal with the lack of active state, we need to use
the mask/unmask primitives (after all, the active state is just an
additional mask on top of the normal one).
To avoid adding a bunch of ugly conditionals in the timer and vgic
code, let's use a timer-specific irqdomain to deal with the state
conversion. Yes, this is an unexpected use of irqdomains, but
there is no reason not to be just as creative as the designers
of the HW...
This involves overloading the vcpu_affinity, set_irqchip_state
and eoi callbacks so that the rest of the KVM code can continue
ignoring the oddities of the underlying platform.
Signed-off-by: Marc Zyngier <maz@kernel.org>
As we are about to add some more things to the timer IRQ
configuration, move this code out of the main timer init code
into its own set of functions.
No functional changes.
Signed-off-by: Marc Zyngier <maz@kernel.org>
In order to deal with these systems that do not offer HW-based
deactivation of interrupts, let implement a SW-based approach:
- When the irq is queued into a LR, treat it as a pure virtual
interrupt and set the EOI flag in the LR.
- When the interrupt state is read back from the LR, force a
deactivation when the state is invalid (neither active nor
pending)
Interrupts requiring such treatment get the VGIC_SW_RESAMPLE flag.
Signed-off-by: Marc Zyngier <maz@kernel.org>
We already have the option to attach a callback to an interrupt
to retrieve its pending state. As we are planning to expand this
facility, move this callback into its own data structure.
This will limit the size of individual interrupts as the ops
structures can be shared across multiple interrupts.
Signed-off-by: Marc Zyngier <maz@kernel.org>
The vGIC, as architected by ARM, allows a virtual interrupt to
trigger the deactivation of a physical interrupt. This allows
the following interrupt to be delivered without requiring an exit.
However, some implementations have choosen not to implement this,
meaning that we will need some unsavoury workarounds to deal with this.
On detecting such a case, taint the kernel and spit a nastygram.
We'll deal with this in later patches.
Signed-off-by: Marc Zyngier <maz@kernel.org>
As it turns out, not all the interrupt controllers are able to
expose a vGIC maintenance interrupt that can be independently
enabled/disabled.
And to be fair, it doesn't really matter as all we require is
for the interrupt to kick us out of guest mode out way or another.
To that effect, add gic_kvm_info.no_maint_irq_mask for an interrupt
controller to advertise the lack of masking.
Signed-off-by: Marc Zyngier <maz@kernel.org>
As we we now entertain the possibility of FIQ being used on the host,
treat the signalling of a FIQ while running a guest as an IRQ,
causing an exit instead of a HYP panic.
Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
The vGIC advertising code is unsurprisingly very much tied to
the GIC implementations. However, we are about to extend the
support to lesser implementations.
Let's dissociate the vgic registration from the GIC code and
move it into KVM, where it makes a bit more sense. This also
allows us to mark the gic_kvm_info structures as __initdata.
Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
The first UART controller in "Everything-Else" power domain, usually used
for Bluetooth HCI has 128bytes FIFO depth.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20210518075833.3736038-4-narmstrong@baylibre.com
The sc7280 IDP board is also called senor in the Chrome OS builds.
Add the "google,senor" compatible so coreboot/depthcharge knows what
device tree blob to pick
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Link: https://lore.kernel.org/r/1619674827-26650-2-git-send-email-rnayak@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Move rmtfs memory region so that it does not overlap with system
RAM (kernel data) when KAsan is enabled. This puts rmtfs right
after mba_mem which is not supposed to increase beyond 0x94600000
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Sujit Kautkar <sujitka@chromium.org>
Link: https://lore.kernel.org/r/20210514113430.1.Ic2d032cd80424af229bb95e2c67dd4de1a70cb0c@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add support for the video, gpu, display, lpass clock controller
device nodes for SC7280 SoC.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Link: https://lore.kernel.org/r/1618020280-5470-3-git-send-email-tdas@codeaurora.org
[bjorn: Dropped includes, as they are not present in v5.13-rc1]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add ADC and thermal monitor configuration for skin temperature,
plus a thermal zone that monitors the skin temperature and uses
the big cores as cooling devices.
CoachZ rev1 is stuffed with an incompatible thermistor for the
skin temperature, disable the thermal zone for rev1 to avoid
the use of bogus temperature values.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20210414111007.v1.1.I1a438604a79025307f177347d45815987b105cb5@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
As per Dmitry Baryshkov [1]:
a) The 2nd "reg" should be 0x3c because "Offset 0x38 is
USB3_DP_COM_REVISION_ID3 (not used by the current driver though)."
b) The 3rd "reg" "is a serdes region and qmp_v3_dp_serdes_tbl contains
registers 0x148 and 0x154."
I think because the 3rd "reg" is a serdes region we should just use
the same size as the 1st "reg"?
[1] https://lore.kernel.org/r/ee5695bb-a603-0dd5-7a7f-695e919b1af1@linaro.org
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Jeykumar Sankaran <jsanka@codeaurora.org>
Cc: Chandan Uddaraju <chandanu@codeaurora.org>
Cc: Vara Reddy <varar@codeaurora.org>
Cc: Tanmay Shah <tanmay@codeaurora.org>
Cc: Rob Clark <robdclark@chromium.org>
Fixes: 58fd7ae621 ("arm64: dts: qcom: sc7180: Update dts for DP phy inside QMP phy")
Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210315103836.1.I9a97120319d43b42353aeac4d348624d60687df7@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Use sm8250 compatibles instead of sdm845 compatibles
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210329120051.3401567-5-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
We should indicate that we're not using the HPD pin on this device, per
the binding document. Otherwise if code in the future wants to enable
HPD in the bridge when this property is absent we'll be enabling HPD
when it isn't supposed to be used. Presumably this board isn't using hpd
on the bridge.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Steev Klimaszewski <steev@kali.org>
Fixes: 956e9c85f4 ("arm64: dts: qcom: c630: Define eDP bridge and panel")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210324231424.2890039-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In accordance with the DWC USB3 bindings the corresponding node
name is suppose to comply with the Generic USB HCD DT schema, which
requires the USB nodes to have the name acceptable by the regexp:
"^usb(@.*)?" . Make sure the "snps,dwc3"-compatible nodes are correctly
named.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210324204836.29668-8-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
We should indicate that we're not using the HPD pin on this device, per
the binding document. Otherwise if code in the future wants to enable
HPD in the bridge when this property is absent we'll be wasting power
powering hpd when we don't use it on trogdor boards. We didn't notice
this before because the kernel driver blindly disables hpd, but that
won't be true for much longer.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: Douglas Anderson <dianders@chromium.org>
Fixes: 7ec3e67307 ("arm64: dts: qcom: sc7180-trogdor: add initial trogdor and lazor dt")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210324025534.1837405-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reserve GPIO pins 85-88 as these aren't meant to be accessible from the
application CPUs (causes reboot). Yet another fix similar to
9134586715, 5f8d3ab136, which is needed to allow angler to boot after
3edfb7bd76 ("gpiolib: Show correct direction from the beginning").
Fixes: feeaf56ac7 ("arm64: dts: msm8994 SoC and Huawei Angler (Nexus 6P) support")
Signed-off-by: Petr Vorel <petr.vorel@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210415193913.1836153-1-petr.vorel@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fix the compatible to make the driver probe and tell the
driver where to look for the "xo" clock to make sure everything
works.
Then we get a happy (eh, happier) 8996:
somainline-sdcard:/home/konrad# cat /sys/kernel/debug/clk/pwrcl_pll/clk_rate
1152000000
Don't backport without "arm64: dts: qcom: msm8996: Add CPU opps", as
the system fails to boot without consumers for these clocks.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210527192958.775434-1-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add the operating points capabilities of the kryo CPUs, that can be
used for frequency scaling. There are two differents operating point
tables, one for the big cluster and one for the LITTLE cluster.
This frequency scaling support can then be used as a passive cooling
device (cpufreq cooling device).
Only add nominal fmax for now, since there is no dynamic control of
VDD APC (s11..) which is statically set at its nominal value.
Original patch link: https://patchwork.kernel.org/project/linux-arm-msm/patch/1595253740-29466-6-git-send-email-loic.poulain@linaro.org/
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
[konrad: drop the thermals part, rebase and remove spaces within <>]
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210527194455.782108-2-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
CoachZ rev3 uses a 100k NTC thermistor for the charger temperatures,
instead of the 47k NTC that is stuffed in earlier revisions. Add .dts
files for rev3.
The 47k NTC currently isn't supported by the PM6150 ADC driver.
Disable the charger thermal zone for rev1 and rev2 to avoid the use
of bogus temperature values.
This also gets rid of the explicit DT files for rev2 and handles
rev2 in the rev1 .dts instead. There was some back and forth
downstream involving the 'dmic_clk_en' pin, after that was sorted
out the DT for rev1 and rev2 is the same.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210322094628.v4.3.I95b8a63103b77cab6a7cf9c150f0541db57fda98@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The only kernel visible change with respect to rev2 is that pompom
rev3 changed the charger thermistor from a 47k to a 100k NTC to use
a thermistor which is supported by the PM6150 ADC driver.
Disable the charger thermal zone for pompom rev1 and rev2 to avoid
the use of bogus temperature values from the unsupported thermistor.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210322094628.v4.2.I4138c3edee23d1efa637eef51e841d9d2e266659@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Commit f73558cc83d1 ("arm64: dts: qcom: sc7180: Disable charger
thermal zone for lazor") disables the charger thermal zone for
specific lazor revisions due to an unsupported thermistor type.
The initial idea was to disable the thermal zone for older
revisions and leave it enabled for newer ones that use a
supported thermistor. Finally the thermistor won't be changed
on newer revisions, hence the thermal zone should be disabled
for all lazor (and limozeen) revisions. Instead of disabling
it per revision do it once in the shared .dtsi for lazor.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210322094628.v4.1.I6d587e7ae72a5a47253bb95dfdc3158f8cc8a157@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
We had introduced the QUP-CORE ICC path to put proxy votes from
QUP wrapper on behalf of earlycon, if other users of QUP-CORE turn
off this clock before the real console is probed, unclocked access
to HW was seen from earlycon.
With ICC sync state support proxy votes are no longer need as ICC
will ensure that the default bootloader votes are not removed until
all it's consumer are probed.
We can safely remove ICC path for QUP-CORE clock from QUP wrapper
device.
Signed-off-by: Roja Rani Yarubandi <rojay@codeaurora.org>
Signed-off-by: Akash Asthana <akashast@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20210324101836.25272-3-rojay@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Some node unit addresses were put wrongly in the dts, resulting in
below warning when run with W=1
arch/arm64/boot/dts/qcom/sm8350.dtsi:693.34-702.5: Warning (simple_bus_reg): /soc@0/thermal-sensor@c222000: simple-bus unit address format error, expected "c263000"
arch/arm64/boot/dts/qcom/sm8350.dtsi:704.34-713.5: Warning (simple_bus_reg): /soc@0/thermal-sensor@c223000: simple-bus unit address format error, expected "c265000"
arch/arm64/boot/dts/qcom/sm8350.dtsi:1180.32-1185.5: Warning (simple_bus_reg): /soc@0/interconnect@90e0000: simple-bus unit address format error, expected "90c0000"
Fix by correcting to the correct address as given in reg node
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210513060733.382420-1-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
With this patch, DMA has a chance of probing and doing something
useful.
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@microsoft.com>
Link: https://lore.kernel.org/r/20210417061951.2105530-3-balbi@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The speedbin value blown in the efuse is used to determine is used to
determine the voltage and frequency value for different IPs, including
GPU, CPUs... So it's really not a gpu specific information.
This patch simply renames 'gpu_speed_bin' node to 'speedbin'.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210527194455.782108-1-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
One of the QUSB USB PHY-s has been left enabled by
default, this is probably just a mistake as other
USB PHY-s are disabled by default.
It makes no sense to have it enabled by default as
not all board implement USB ports, so disable it.
Reviewed-by: Kathiravan T <kathirav@codeaurora.org>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Link: https://lore.kernel.org/r/20210526150125.1816335-1-robimarko@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Correct the voltages in the "Power Optimized" (<= 1.5 GHz) Cortex-A57
operating point table entries for the R-Car M3-W and M3-W+ SoCs from
0.82V to 0.83V, as per the R-Car Gen3 EC Manual Errata for Revision
0.53.
Based on a patch for R-Car M3-W in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.
Fixes: da7e311334 ("arm64: dts: renesas: r8a7796: Add OPPs table for cpu devices")
Fixes: f51746ad7d ("arm64: dts: renesas: Add Renesas R8A77961 SoC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/b9e9db907514790574429b83d070c823b36085ef.1619699909.git.geert+renesas@glider.be
Tag the highest "Power Optimized" (1.5 GHz) Cortex-A57 operating point
table entries for the RZ/G2M, R-Car M3-W and M3-W+ SoCs with the
"opp-suspend" property. This makes sure the system will enter suspend
in the same performance state as it will be resumed by the firmware
later, avoiding state inconsistencies after resume.
Based on a patch for R-Car M3-W in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.
Fixes: 800037e815 ("arm64: dts: renesas: r8a774a1: Add operating points")
Fixes: da7e311334 ("arm64: dts: renesas: r8a7796: Add OPPs table for cpu devices")
Fixes: f51746ad7d ("arm64: dts: renesas: Add Renesas R8A77961 SoC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/45a061c3b0463aac7d10664f47c4afdd999da50d.1619699721.git.geert+renesas@glider.be
This fix the recent removal of clock drivers selection.
While it is not necessary to select the clock drivers themselves, we need
to select a proper implementation of the clock API, which for the meson, is
CCF
Fixes: ba66a25536 ("arm64: meson: ship only the necessary clock controllers")
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210429083823.59546-1-jbrunet@baylibre.com
* Another state update on exit to userspace fix
* Prevent the creation of mixed 32/64 VMs
* Fix regression with irqbypass not restarting the guest on failed connect
* Fix regression with debug register decoding resulting in overlapping access
* Commit exception state on exit to usrspace
* Fix the MMU notifier return values
* Add missing 'static' qualifiers in the new host stage-2 code
x86 fixes:
* fix guest missed wakeup with assigned devices
* fix WARN reported by syzkaller
* do not use BIT() in UAPI headers
* make the kvm_amd.avic parameter bool
PPC fixes:
* make halt polling heuristics consistent with other architectures
selftests:
* various fixes
* new performance selftest memslot_perf_test
* test UFFD minor faults in demand_paging_test
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmCyF0MUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroOHSgf/Q4Hm5e12Bj2xJy6A+iShnrbbT8PW
hcIIOA7zGWXfjVYcBV7anbj7CcpzfIz0otcRBABa5mkhj+fb3YmPEb0EzCPi4Hru
zxpcpB2w7W7WtUOIKe2EmaT+4Pk6/iLcfr8UMHMqx460akE9OmIg10QNWai3My/3
RIOeakSckBI9e/1TQZbxH66dsLwCT0lLco7i7AWHdFxkzUQyoA34HX5pczOCBsO5
3nXH+/txnRVhqlcyzWLVVGVzFqmpHtBqkIInDOXfUqIoxo/gOhOgF1QdMUEKomxn
5ZFXlL5IXNtr+7yiI67iHX7CWkGZE9oJ04TgPHn6LR6wRnVvc3JInzcB5Q==
=ollO
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"ARM fixes:
- Another state update on exit to userspace fix
- Prevent the creation of mixed 32/64 VMs
- Fix regression with irqbypass not restarting the guest on failed
connect
- Fix regression with debug register decoding resulting in
overlapping access
- Commit exception state on exit to usrspace
- Fix the MMU notifier return values
- Add missing 'static' qualifiers in the new host stage-2 code
x86 fixes:
- fix guest missed wakeup with assigned devices
- fix WARN reported by syzkaller
- do not use BIT() in UAPI headers
- make the kvm_amd.avic parameter bool
PPC fixes:
- make halt polling heuristics consistent with other architectures
selftests:
- various fixes
- new performance selftest memslot_perf_test
- test UFFD minor faults in demand_paging_test"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (44 commits)
selftests: kvm: fix overlapping addresses in memslot_perf_test
KVM: X86: Kill off ctxt->ud
KVM: X86: Fix warning caused by stale emulation context
KVM: X86: Use kvm_get_linear_rip() in single-step and #DB/#BP interception
KVM: x86/mmu: Fix comment mentioning skip_4k
KVM: VMX: update vcpu posted-interrupt descriptor when assigning device
KVM: rename KVM_REQ_PENDING_TIMER to KVM_REQ_UNBLOCK
KVM: x86: add start_assignment hook to kvm_x86_ops
KVM: LAPIC: Narrow the timer latency between wait_lapic_expire and world switch
selftests: kvm: do only 1 memslot_perf_test run by default
KVM: X86: Use _BITUL() macro in UAPI headers
KVM: selftests: add shared hugetlbfs backing source type
KVM: selftests: allow using UFFD minor faults for demand paging
KVM: selftests: create alias mappings when using shared memory
KVM: selftests: add shmem backing source type
KVM: selftests: refactor vm_mem_backing_src_type flags
KVM: selftests: allow different backing source types
KVM: selftests: compute correct demand paging size
KVM: selftests: simplify setup_demand_paging error handling
KVM: selftests: Print a message if /dev/kvm is missing
...
The MCU RGMII MCU_RGMII1_TXC pin is defined as input by mistake, although
this does not make any difference functionality wise it's better to update
to avoid confusion.
Hence fix MCU RGMII MCU_RGMII1_TXC pin pinmux definitions to be an output
in K3 am654x/j721e/j7200 board files.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210526132041.6104-1-grygorii.strashko@ti.com
Enable work around feature built into the controller to address issue with
RX Sensitivity for USB2 PHY.
Fixes: 6197d7139d ("arm64: dts: ti: k3-j7200-main: Add USB controller")
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210512153308.5840-1-a-govindraju@ti.com
The current scheme for audio card names is suboptimal because it causes
the automatically generated names (for ID and driver) to be truncated,
which in turn can cause conflicts.
Introduce a new scheme which reuses the board model for the names and
appends the "HDA" and "APE" suffixes for the HDA and APE, respectively.
As a side-effect these suffixes end up being used as the ID of the SoC
sound cards which makes it easy for users to select them when using the
ALSA command-line utilities, for example.
As a separate measure, the driver name for the cards is now set by the
corresponding audio driver (either tegra-hda or tegra-ape), making it a
more useful identifier than the currently normalized card name.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Populate the device-tree node for the PMU device on Tegra194. This also
fixes the following warning that is observed on booting Tegra194.
ERR KERN kvm: pmu event creation failed -2
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable audio capture frontends and a tdm decoder.
This makes it possible to loopback the audio played on the hdmi codec,
which is the only output interface at the moment.
Of course, one TODDR device would be enough to do that but since
the 3 FRDDRs are enabled on the playback side, let's do the same on the
capture side.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210429084253.59692-1-jbrunet@baylibre.com
- Don't use contiguous or block mappings for the linear map when KFENCE
is enabled.
- Fix link in the arch_counter_enforce_ordering() comment.
-----BEGIN PGP SIGNATURE-----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=gSNa
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Don't use contiguous or block mappings for the linear map when KFENCE
is enabled.
- Fix link in the arch_counter_enforce_ordering() comment.
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mm: don't use CON and BLK mapping if KFENCE is enabled
arm64: Fix stale link in the arch_counter_enforce_ordering() comment
The scs_load and scs_save asm macros don't make use of the mandatory
'tmp' register argument, so drop it and fix up the callers.
Cc: Sami Tolvanen <samitolvanen@google.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Link: https://lore.kernel.org/r/20210527105529.21967-1-will@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Create necessary functions to encode/decode aarch64 barrier
instructions.
DSB needs special case handling as it has multiple encodings.
Signed-off-by: Julien Thierry <jthierry@redhat.com>
Link: https://lore.kernel.org/r/20210303170536.1838032-7-jthierry@redhat.com
[will: Don't reject DSB #4]
Signed-off-by: Will Deacon <will@kernel.org>
Aarch64 instruction set encoding and decoding logic can prove useful
for some features/tools both part of the kernel and outside the kernel.
Isolate the function dealing only with encoding/decoding instructions,
with minimal dependency on kernel utilities in order to be able to reuse
that code.
Code was only moved, no code should have been added, removed nor
modifier.
Signed-off-by: Julien Thierry <jthierry@redhat.com>
Link: https://lore.kernel.org/r/20210303170536.1838032-5-jthierry@redhat.com
Signed-off-by: Will Deacon <will@kernel.org>
The functions to check condition flags for aarch32 execution is only
used to emulate aarch32 instructions. Move them from the instruction
encoding/decoding code to the trap handling files.
Signed-off-by: Julien Thierry <jthierry@redhat.com>
Link: https://lore.kernel.org/r/20210303170536.1838032-3-jthierry@redhat.com
[will: leave aarch32_opcode_cond_checks where it is]
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
Files insn.[c|h] containt some functions used for instruction patching.
In order to reuse the instruction encoder/decoder, move the patching
utilities to their own file.
Signed-off-by: Julien Thierry <jthierry@redhat.com>
Link: https://lore.kernel.org/r/20210303170536.1838032-2-jthierry@redhat.com
[will: Include patching.h in insn.h to fix header mess; add __ASSEMBLY__ guards]
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
It looks like we have tolerated creating mixed-width VMs since...
forever. However, that was never the intention, and we'd rather
not have to support that pointless complexity.
Forbid such a setup by making sure all the vcpus have the same
register width.
Reported-by: Steven Price <steven.price@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20210524170752.1549797-1-maz@kernel.org
Commit 26778aaa13 ("KVM: arm64: Commit pending PC adjustemnts before
returning to userspace") fixed the PC updating issue by forcing an explicit
synchronisation of the exception state on vcpu exit to userspace.
However, we forgot to take into account the case where immediate_exit is
set by userspace and KVM_RUN will exit immediately. Fix it by resolving all
pending PC updates before returning to userspace.
Since __kvm_adjust_pc() relies on a loaded vcpu context, I moved the
immediate_exit checking right after vcpu_load(). We will get some overhead
if immediate_exit is true (which should hopefully be rare).
Fixes: 26778aaa13 ("KVM: arm64: Commit pending PC adjustemnts before returning to userspace")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210526141831.1662-1-yuzenghui@huawei.com
Cc: stable@vger.kernel.org # 5.11
can and wireless trees. Notably including fixes for the recently
announced "FragAttacks" WiFi vulnerabilities. Rather large batch,
touching some core parts of the stack, too, but nothing hair-raising.
Current release - regressions:
- tipc: make node link identity publish thread safe
- dsa: felix: re-enable TAS guard band mode
- stmmac: correct clocks enabled in stmmac_vlan_rx_kill_vid()
- stmmac: fix system hang if change mac address after interface ifdown
Current release - new code bugs:
- mptcp: avoid OOB access in setsockopt()
- bpf: Fix nested bpf_bprintf_prepare with more per-cpu buffers
- ethtool: stats: fix a copy-paste error - init correct array size
Previous releases - regressions:
- sched: fix packet stuck problem for lockless qdisc
- net: really orphan skbs tied to closing sk
- mlx4: fix EEPROM dump support
- bpf: fix alu32 const subreg bound tracking on bitwise operations
- bpf: fix mask direction swap upon off reg sign change
- bpf, offload: reorder offload callback 'prepare' in verifier
- stmmac: Fix MAC WoL not working if PHY does not support WoL
- packetmmap: fix only tx timestamp on request
- tipc: skb_linearize the head skb when reassembling msgs
Previous releases - always broken:
- mac80211: address recent "FragAttacks" vulnerabilities
- mac80211: do not accept/forward invalid EAPOL frames
- mptcp: avoid potential error message floods
- bpf, ringbuf: deny reserve of buffers larger than ringbuf to prevent
out of buffer writes
- bpf: forbid trampoline attach for functions with variable arguments
- bpf: add deny list of functions to prevent inf recursion of tracing
programs
- tls splice: check SPLICE_F_NONBLOCK instead of MSG_DONTWAIT
- can: isotp: prevent race between isotp_bind() and isotp_setsockopt()
- netfilter: nft_set_pipapo_avx2: Add irq_fpu_usable() check,
fallback to non-AVX2 version
Misc:
- bpf: add kconfig knob for disabling unpriv bpf by default
-----BEGIN PGP SIGNATURE-----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=peMK
-----END PGP SIGNATURE-----
Merge tag 'net-5.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes for 5.13-rc4, including fixes from bpf, netfilter,
can and wireless trees. Notably including fixes for the recently
announced "FragAttacks" WiFi vulnerabilities. Rather large batch,
touching some core parts of the stack, too, but nothing hair-raising.
Current release - regressions:
- tipc: make node link identity publish thread safe
- dsa: felix: re-enable TAS guard band mode
- stmmac: correct clocks enabled in stmmac_vlan_rx_kill_vid()
- stmmac: fix system hang if change mac address after interface
ifdown
Current release - new code bugs:
- mptcp: avoid OOB access in setsockopt()
- bpf: Fix nested bpf_bprintf_prepare with more per-cpu buffers
- ethtool: stats: fix a copy-paste error - init correct array size
Previous releases - regressions:
- sched: fix packet stuck problem for lockless qdisc
- net: really orphan skbs tied to closing sk
- mlx4: fix EEPROM dump support
- bpf: fix alu32 const subreg bound tracking on bitwise operations
- bpf: fix mask direction swap upon off reg sign change
- bpf, offload: reorder offload callback 'prepare' in verifier
- stmmac: Fix MAC WoL not working if PHY does not support WoL
- packetmmap: fix only tx timestamp on request
- tipc: skb_linearize the head skb when reassembling msgs
Previous releases - always broken:
- mac80211: address recent "FragAttacks" vulnerabilities
- mac80211: do not accept/forward invalid EAPOL frames
- mptcp: avoid potential error message floods
- bpf, ringbuf: deny reserve of buffers larger than ringbuf to
prevent out of buffer writes
- bpf: forbid trampoline attach for functions with variable arguments
- bpf: add deny list of functions to prevent inf recursion of tracing
programs
- tls splice: check SPLICE_F_NONBLOCK instead of MSG_DONTWAIT
- can: isotp: prevent race between isotp_bind() and
isotp_setsockopt()
- netfilter: nft_set_pipapo_avx2: Add irq_fpu_usable() check,
fallback to non-AVX2 version
Misc:
- bpf: add kconfig knob for disabling unpriv bpf by default"
* tag 'net-5.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (172 commits)
net: phy: Document phydev::dev_flags bits allocation
mptcp: validate 'id' when stopping the ADD_ADDR retransmit timer
mptcp: avoid error message on infinite mapping
mptcp: drop unconditional pr_warn on bad opt
mptcp: avoid OOB access in setsockopt()
nfp: update maintainer and mailing list addresses
net: mvpp2: add buffer header handling in RX
bnx2x: Fix missing error code in bnx2x_iov_init_one()
net: zero-initialize tc skb extension on allocation
net: hns: Fix kernel-doc
sctp: fix the proc_handler for sysctl encap_port
sctp: add the missing setting for asoc encap_port
bpf, selftests: Adjust few selftest result_unpriv outcomes
bpf: No need to simulate speculative domain for immediates
bpf: Fix mask direction swap upon off reg sign change
bpf: Wrap aux data inside bpf_sanitize_info container
bpf: Fix BPF_LSM kconfig symbol dependency
selftests/bpf: Add test for l3 use of bpf_redirect_peer
bpftool: Add sock_release help info for cgroup attach/prog load command
net: dsa: microchip: enable phy errata workaround on 9567
...
By using outlined checks we can achieve a significant code size
improvement by moving the tag-based ASAN checks into separate
functions. Unlike the existing CONFIG_KASAN_OUTLINE mode these
functions have a custom calling convention that preserves most
registers and is specialized to the register containing the address
and the type of access, and as a result we can eliminate the code
size and performance overhead of a standard calling convention such
as AAPCS for these functions.
This change depends on a separate series of changes to Clang [1] to
support outlined checks in the kernel, although the change works fine
without them (we just don't get outlined checks). This is because the
flag -mllvm -hwasan-inline-all-checks=0 has no effect until the Clang
changes land. The flag was introduced in the Clang 9.0 timeframe as
part of the support for outlined checks in userspace and because our
minimum Clang version is 10.0 we can pass it unconditionally.
Outlined checks require a new runtime function with a custom calling
convention. Add this function to arch/arm64/lib.
I measured the code size of defconfig + tag-based KASAN, as well
as boot time (i.e. time to init launch) on a DragonBoard 845c with
an Android arm64 GKI kernel. The results are below:
code size boot time
CONFIG_KASAN_INLINE=y before 92824064 6.18s
CONFIG_KASAN_INLINE=y after 38822400 6.65s
CONFIG_KASAN_OUTLINE=y 39215616 11.48s
We can see straight away that specialized outlined checks beat the
existing CONFIG_KASAN_OUTLINE=y on both code size and boot time
for tag-based ASAN.
As for the comparison between CONFIG_KASAN_INLINE=y before and after
we saw similar performance numbers in userspace [2] and decided
that since the performance overhead is minimal compared to the
overhead of tag-based ASAN itself as well as compared to the code
size improvements we would just replace the inlined checks with the
specialized outlined checks without the option to select between them,
and that is what I have implemented in this patch.
Signed-off-by: Peter Collingbourne <pcc@google.com>
Acked-by: Andrey Konovalov <andreyknvl@gmail.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Link: https://linux-review.googlesource.com/id/I1a30036c70ab3c3ee78d75ed9b87ef7cdc3fdb76
Link: [1] https://reviews.llvm.org/D90426
Link: [2] https://reviews.llvm.org/D56954
Link: https://lore.kernel.org/r/20210526174927.2477847-3-pcc@google.com
Signed-off-by: Will Deacon <will@kernel.org>
Now that we have a consistent place to initialize CPU context registers
early in the boot path, let's also initialize the per-cpu offset here.
This makes the primary and secondary boot paths more consistent, and
allows for the use of per-cpu operations earlier, which will be
necessary for instrumentation with KCSAN.
Note that smp_prepare_boot_cpu() still needs to re-initialize CPU0's
offset as immediately prior to this the per-cpu areas may be
reallocated, and hence the boot-time offset may be stale. A comment is
added to make this clear.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Suzuki Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210520115031.18509-7-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Once we enable the MMU, we have to initialize:
* SP_EL0 to point at the active task
* SP to point at the active task's stack
* SCS_SP to point at the active task's shadow stack
For all tasks (including init_task), this information can be derived
from the task's task_struct.
Let's unify __primary_switched and __secondary_switched to consistently
acquire this information from the relevant task_struct. At the same
time, let's fold this together with initializing a task's final frame.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Suzuki Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210520115031.18509-6-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
When we boot a secondary CPU, we pass it a task and a stack to use. As
the stack is always the task's stack, which can be derived from the
task, let's have the secondary CPU derive this itself and avoid passing
redundant information.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Suzuki Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210520115031.18509-5-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
All reads and writes of secondary_data occur with the MMU on, using
coherent attributes, so there's no need to perform any cache maintenance
for this.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Suzuki Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210520115031.18509-4-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Suzuki Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210520115031.18509-3-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
The GMID_EL1.BS field determines the number of tags accessed by the
LDGM/STGM instructions (EL1 and up), used by the kernel for copying or
zeroing page tags.
Taint the kernel if GMID_EL1.BS differs between CPUs but only of
CONFIG_ARM64_MTE is enabled.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Suzuki K Poulose <Suzuki.Poulose@arm.com>
Link: https://lore.kernel.org/r/20210526193621.21559-3-catalin.marinas@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
The architecture has been updated and the CTR_EL0, CNTFRQ_EL0,
DCZID_EL0, MIDR_EL1, REVIDR_EL1 registers are all 64-bit, even if most
of them have a RES0 top 32-bit.
Change their type to u64 in struct cpuinfo_arm64.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Suzuki K Poulose <Suzuki.Poulose@arm.com>
Link: https://lore.kernel.org/r/20210526193621.21559-2-catalin.marinas@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
When the SVE vector length is 128 bits then there are no bits in the Z
registers which are not shared with the V registers so we can skip them
when zeroing state not shared with FPSIMD, this results in a minor
performance improvement.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20210512151131.27877-4-broonie@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
This makes the code a bit clearer and as a result we can also make the
indentation more normal, there is no change to the generated code.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20210512151131.27877-3-broonie@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Trivial refactoring to support further work, no change to generated code.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20210512151131.27877-2-broonie@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
The AAPCS places no requirements on the alignment of the frame
record. In theory it could be placed anywhere, although it seems
sensible to require it to be aligned to 8 bytes. With an upcoming
enhancement to tag-based KASAN Clang will begin creating frame records
located at an address that is only aligned to 8 bytes. Accommodate
such frame records in the stack unwinding code.
As pointed out by Mark Rutland, the userspace stack unwinding code
has the same problem, so fix it there as well.
Signed-off-by: Peter Collingbourne <pcc@google.com>
Link: https://linux-review.googlesource.com/id/Ia22c375230e67ca055e9e4bb639383567f7ad268
Acked-by: Andrey Konovalov <andreyknvl@gmail.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20210526174927.2477847-2-pcc@google.com
Signed-off-by: Will Deacon <will@kernel.org>
unwind_frame() was previously implicitly checking that the frame
record is in bounds of the stack by enforcing that FP is both aligned
to 16 and in bounds of the stack. Once the FP alignment requirement
is relaxed to 8 this will not be sufficient because it does not
account for the case where FP points to 8 bytes before the end of the
stack.
Make the check explicit by changing the on_*stack functions to take a
size argument and adjusting the callers to pass the appropriate sizes.
Signed-off-by: Peter Collingbourne <pcc@google.com>
Link: https://linux-review.googlesource.com/id/Ib7a3eb3eea41b0687ffaba045ceb2012d077d8b4
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20210526174927.2477847-1-pcc@google.com
Signed-off-by: Will Deacon <will@kernel.org>
Merge in SMCCC update from Sudeep, which is a branch shared with arm-soc
for the FF-A driver work.
* for-next/ffa:
arm64: smccc: Add support for SMCCCv1.2 extended input/output registers
SMCCC v1.2 allows x8-x17 to be used as parameter registers and x4—x17
to be used as result registers in SMC64/HVC64. Arm Firmware Framework
for Armv8-A specification makes use of x0-x7 as parameter and result
registers. There are other users like Hyper-V who intend to use beyond
x0-x7 as well.
Current SMCCC interface in the kernel just use x0-x7 as parameter and
x0-x3 as result registers as required by SMCCCv1.0. Let us add new
interface to support this extended set of input/output registers namely
x0-x17 as both parameter and result registers.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Cc: Will Deacon <will@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210518163618.43950-1-sudeep.holla@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
arch/$(SRCARCH)/Kbuild is useful for Makefile cleanups because you can
use the obj-y syntax.
Add an empty file if it is missing in arch/$(SRCARCH)/.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Now that all architectures implement ARCH_ATOMIC, we can make it
mandatory, removing the Kconfig symbol and logic for !ARCH_ATOMIC.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20210525140232.53872-33-mark.rutland@arm.com
Subsequent patches will move architectures over to the ARCH_ATOMIC API,
after preparing the asm-generic atomic implementations to function with
or without ARCH_ATOMIC.
As some architectures use the asm-generic implementations exclusively
(and don't have a local atomic.h), and to avoid the risk that
ARCH_ATOMIC isn't defined in some cases we expect, let's make the
ARCH_ATOMIC macro a Kconfig symbol instead, so that we can guarantee it
is consistently available where needed.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20210525140232.53872-2-mark.rutland@arm.com
As the name implies, the USB2 controller should only operate at
USB2 speeds. Make sure it does just that by pinning it to USB
High-Speed (USB2) mode.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210525200246.118323-3-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add channel nodes for the on die temperatures of PMICS
pmk8350, pm8350, pmr735a and pmr735b.
Signed-off-by: satya priya <skakit@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/1621937466-1502-11-git-send-email-skakit@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add gpio ranges and correct the compatible to add
"qcom,spmi-gpio" as this pmic is on spmi bus.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: satya priya <skakit@codeaurora.org>
Link: https://lore.kernel.org/r/1621937466-1502-9-git-send-email-skakit@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add gpio ranges and correct the compatible to add
"qcom,spmi-gpio" as this pmic is on spmi bus.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: satya priya <skakit@codeaurora.org>
Link: https://lore.kernel.org/r/1621937466-1502-7-git-send-email-skakit@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add gpio ranges and correct the compatible to add
"qcom,spmi-gpio" as this pmic is on spmi bus.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: satya priya <skakit@codeaurora.org>
Link: https://lore.kernel.org/r/1621937466-1502-5-git-send-email-skakit@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Disable Venus by default to allow booting without closed firmware and
enable it on the boards that didn't previously disable it. This commit
brings no functional difference.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210228130831.203765-7-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Disable them by default to allow for booting without a display
and proprietary firmware. Then, enable them on boards that didn't
previously disable them. Hence, this commit brings no functional
difference.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210228130831.203765-6-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Set the tcsr_mutex_regs size to 0x40000 to allow for accessing
all required registers that will be needed to support modem.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210228130831.203765-3-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
QUP and UART names start from 1. There are 6 QUPs and 2 UARTs
per BLSP. Let's not further confuse programmers by stating
otherwise.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210228130831.203765-2-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In order to prepare for feature development, the DTs
have to be workable with.. To achieve that:
- Rename msmgpio to tlmm (consistency with newer DTs)
- Rid msm8996-pins.dtsi and add the contents to msm8996.dtsi
- Modernize the pin nodes, make them more concise
- Add generic pin configuration for some hardware
- Fix up some names in preparation for BLSP/UART name cleaning..
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210228130831.203765-1-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
qcom camera driver allocates the ICP firmware memory
dynamically, so the carveout region is unnecessary.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Link: https://lore.kernel.org/r/20210525133242.188603-1-senozhatsky@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This patch adds audio support for Xiaomi Poco F1 phone. Phone's primary
Mic and 3.5mm Headphone jack are handled through the SDM845 sound card
and WCD9340 codec.
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Joel Selvaraj <jo@jsfamily.in>
Link: https://lore.kernel.org/r/BN6PR2001MB17966ED1D787FA3F4B90A1A7D95B9@BN6PR2001MB1796.namprd20.prod.outlook.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The rmtfs_mem region is a weird one, downstream allocates it
dynamically, and supports a "qcom,guard-memory" property which when set
will reserve 4k above and below the rmtfs memory.
A common from qcom 4.9 kernel msm_sharedmem driver:
/*
* If guard_memory is set, then the shared memory region
* will be guarded by SZ_4K at the start and at the end.
* This is needed to overcome the XPU limitation on few
* MSM HW, so as to make this memory not contiguous with
* other allocations that may possibly happen from other
* clients in the system.
*/
When the kernel tries to touch memory that is too close the
rmtfs region it may cause an XPU violation. Such is the case on the
OnePlus 6 where random crashes would occur usually after boot.
Reserve 4k above and below the rmtfs_mem to avoid hitting these XPU
Violations.
This doesn't entirely solve the random crashes on the OnePlus 6/6T but
it does seem to prevent the ones which happen shortly after modem
bringup.
Fixes: 288ef8a426 ("arm64: dts: sdm845: add oneplus6/6t devices")
Signed-off-by: Caleb Connolly <caleb@connolly.tech>
Link: https://lore.kernel.org/r/20210502014146.85642-4-caleb@connolly.tech
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Although naming across the codebase isn't that consistent, it
tends to follow certain patterns. Moreover, the term "flush"
isn't defined in the Arm Architecture reference manual, and might
be interpreted to mean clean, invalidate, or both for a cache.
Rename arm64-internal functions to make the naming internally
consistent, as well as making it consistent with the Arm ARM, by
specifying whether it applies to the instruction, data, or both
caches, whether the operation is a clean, invalidate, or both.
Also specify which point the operation applies to, i.e., to the
point of unification (PoU), coherency (PoC), or persistence
(PoP).
This commit applies the following sed transformation to all files
under arch/arm64:
"s/\b__flush_cache_range\b/caches_clean_inval_pou_macro/g;"\
"s/\b__flush_icache_range\b/caches_clean_inval_pou/g;"\
"s/\binvalidate_icache_range\b/icache_inval_pou/g;"\
"s/\b__flush_dcache_area\b/dcache_clean_inval_poc/g;"\
"s/\b__inval_dcache_area\b/dcache_inval_poc/g;"\
"s/__clean_dcache_area_poc\b/dcache_clean_poc/g;"\
"s/\b__clean_dcache_area_pop\b/dcache_clean_pop/g;"\
"s/\b__clean_dcache_area_pou\b/dcache_clean_pou/g;"\
"s/\b__flush_cache_user_range\b/caches_clean_inval_user_pou/g;"\
"s/\b__flush_icache_all\b/icache_inval_all_pou/g;"
Note that __clean_dcache_area_poc is deliberately missing a word
boundary check at the beginning in order to match the efistub
symbols in image-vars.h.
Also note that, despite its name, __flush_icache_range operates
on both instruction and data caches. The name change here
reflects that.
No functional change intended.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Fuad Tabba <tabba@google.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210524083001.2586635-19-tabba@google.com
Signed-off-by: Will Deacon <will@kernel.org>
Fix and expand comments for the cache maintenance functions in
cacheflush.h. Adds comments to functions that weren't described
before. Explains what the functions do using Arm Architecture
Reference Manual terminology.
No functional change intended.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Fuad Tabba <tabba@google.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210524083001.2586635-18-tabba@google.com
Signed-off-by: Will Deacon <will@kernel.org>
To be consistent with other functions with similar names and
functionality in cacheflush.h, cache.S, and cachetlb.rst, change
to specify the range in terms of start and end, as opposed to
start and size.
No functional change intended.
Reported-by: Will Deacon <will@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Fuad Tabba <tabba@google.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210524083001.2586635-17-tabba@google.com
Signed-off-by: Will Deacon <will@kernel.org>
To be consistent with other functions with similar names and
functionality in cacheflush.h, cache.S, and cachetlb.rst, change
to specify the range in terms of start and end, as opposed to
start and size.
No functional change intended.
Reported-by: Will Deacon <will@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Fuad Tabba <tabba@google.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210524083001.2586635-16-tabba@google.com
Signed-off-by: Will Deacon <will@kernel.org>
To be consistent with other functions with similar names and
functionality in cacheflush.h, cache.S, and cachetlb.rst, change
to specify the range in terms of start and end, as opposed to
start and size.
No functional change intended.
Reported-by: Will Deacon <will@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Fuad Tabba <tabba@google.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210524083001.2586635-15-tabba@google.com
Signed-off-by: Will Deacon <will@kernel.org>
To be consistent with other functions with similar names and
functionality in cacheflush.h, cache.S, and cachetlb.rst, change
to specify the range in terms of start and end, as opposed to
start and size.
Because the code is shared with __dma_clean_area, it changes the
parameters for that as well. However, __dma_clean_area is local to
cache.S, so no other users are affected.
No functional change intended.
Reported-by: Will Deacon <will@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Fuad Tabba <tabba@google.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210524083001.2586635-14-tabba@google.com
Signed-off-by: Will Deacon <will@kernel.org>
To be consistent with other functions with similar names and
functionality in cacheflush.h, cache.S, and cachetlb.rst, change
to specify the range in terms of start and end, as opposed to
start and size.
No functional change intended.
Reported-by: Will Deacon <will@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Fuad Tabba <tabba@google.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210524083001.2586635-13-tabba@google.com
Signed-off-by: Will Deacon <will@kernel.org>
To be consistent with other functions with similar names and
functionality in cacheflush.h, cache.S, and cachetlb.rst, change
to specify the range in terms of start and end, as opposed to
start and size.
No functional change intended.
Reported-by: Will Deacon <will@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Fuad Tabba <tabba@google.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210524083001.2586635-12-tabba@google.com
Signed-off-by: Will Deacon <will@kernel.org>
To be consistent with other functions with similar names and
functionality in cacheflush.h, cache.S, and cachetlb.rst, change
to specify the range in terms of start and end, as opposed to
start and size.
Because the code is shared with __dma_inv_area, it changes the
parameters for that as well. However, __dma_inv_area is local to
cache.S, so no other users are affected.
No functional change intended.
Reported-by: Will Deacon <will@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Fuad Tabba <tabba@google.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210524083001.2586635-11-tabba@google.com
Signed-off-by: Will Deacon <will@kernel.org>
Many comments refer to the function flush_icache_range, where the
intent is in fact __flush_icache_range. Fix these comments to
refer to the intended function.
That's probably due to commit 3b8c9f1cdf ("arm64: IPI each
CPU after invalidating the I-cache for kernel mappings"), which
renamed flush_icache_range() to __flush_icache_range() and added
a wrapper.
No functional change intended.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Fuad Tabba <tabba@google.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210524083001.2586635-10-tabba@google.com
Signed-off-by: Will Deacon <will@kernel.org>
The comment describing the macro dcache_by_line_op is placed
right before the previous macro of the one it describes, which is
a bit confusing. Move it to the macro it describes (dcache_by_line_op).
No functional change intended.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Fuad Tabba <tabba@google.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210524083001.2586635-9-tabba@google.com
Signed-off-by: Will Deacon <will@kernel.org>
Since __flush_dcache_area is called right before,
invalidate_icache_range is sufficient in this case.
Rewrite the comment to better explain the rationale behind the
cache maintenance operations used here.
No functional change intended.
Possible performance impact due to invalidating only the icache
rather than invalidating and cleaning both caches.
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/linux-arch/20200511110014.lb9PEahJ4hVOYrbwIb_qUHXyNy9KQzNFdb_I3YlzY6A@z/
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Fuad Tabba <tabba@google.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210524083001.2586635-7-tabba@google.com
Signed-off-by: Will Deacon <will@kernel.org>
invalidate_icache_range() works on kernel addresses, and doesn't
need uaccess. Remove the code that toggles uaccess_ttbr0_enable,
as well as the code that emits an entry into the exception table
(via the macro invalidate_icache_by_line).
Changes return type of invalidate_icache_range() from int (which
used to indicate a fault) to void, since it doesn't need uaccess
and won't fault. Note that return value was never checked by any
of the callers.
No functional change intended.
Possible performance impact due to the reduced number of
instructions.
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/linux-arch/20200511110014.lb9PEahJ4hVOYrbwIb_qUHXyNy9KQzNFdb_I3YlzY6A@z/
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Fuad Tabba <tabba@google.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210524083001.2586635-6-tabba@google.com
Signed-off-by: Will Deacon <will@kernel.org>
__flush_icache_range works on kernel addresses, and doesn't need
uaccess. The existing code is a side-effect of its current
implementation with __flush_cache_user_range fallthrough.
Instead of fallthrough to share the code, use a common macro for
the two where the caller specifies an optional fixup label if
user access is needed. If provided, this label would be used to
generate an extable entry.
Simplify the code to use dcache_by_line_op, instead of
replicating much of its functionality.
No functional change intended.
Possible performance impact due to the reduced number of
instructions.
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Will Deacon <will@kernel.org>
Reported-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/linux-arch/20200511110014.lb9PEahJ4hVOYrbwIb_qUHXyNy9KQzNFdb_I3YlzY6A@z/
Link: https://lore.kernel.org/linux-arm-kernel/20210521121846.GB1040@C02TD0UTHF1T.local/
Signed-off-by: Fuad Tabba <tabba@google.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210524083001.2586635-5-tabba@google.com
Signed-off-by: Will Deacon <will@kernel.org>
The Arm errata covered by ARM64_WORKAROUND_CLEAN_CACHE require
that "dc cvau" instructions get promoted to "dc civac".
Reported-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Fuad Tabba <tabba@google.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210524083001.2586635-4-tabba@google.com
Signed-off-by: Will Deacon <will@kernel.org>
It would be helpful if we could use both `dcache_by_line_op` and
`invalidate_icache_by_line` for user memory without accidentally fixing
up unexpected faults when performing maintenance on kernel addresses.
Let's make this possible by having both macros take an optional fixup
label, and only generating an extable entry if a label is provided.
At the same time, let's clean up the labels used to be globally unique
using \@ as we do for other macros.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Fuad Tabba <tabba@google.com>
Cc: Ard Biesheuvel <aedb@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Fuad Tabba <tabba@google.com>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210524083001.2586635-3-tabba@google.com
Signed-off-by: Will Deacon <will@kernel.org>
The `__dcache_op_workaround_clean_cache` and `dcache_by_line_op` macros
are only expected to be usedc on kernel memory, without a user fault
fixup, and so we named their address variables `kaddr` to make this
clear.
Subseuqent patches will modify these to also work on user memory with an
(optional) user fault fixup, where `kaddr` won't make as much sense. To
aid the legibility of patches, this patch (only) replaces `kaddr` with
`addr` as a preparatory step.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Fuad Tabba <tabba@google.com>
Cc: Ard Biesheuvel <aedb@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Fuad Tabba <tabba@google.com>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210524083001.2586635-2-tabba@google.com
Signed-off-by: Will Deacon <will@kernel.org>
vmemmap_free() callsites (mm/sparse.c) and declaration (include/linux/mm.h)
are protected with CONFIG_MEMORY_HOTPLUG. This function is not required if
CONFIG_MEMORY_HOTPLUG is not enabled. Hence move the config wrapper outside
the function definition.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Link: https://lore.kernel.org/r/1621842030-23256-1-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Use DC GVA / DC GZVA to speed up KASan memory tagging in HW tags mode.
The first cacheline is always tagged using STG/STZG even if the address is
cacheline-aligned, as benchmarks show it is faster than a conditional
branch.
Signed-off-by: Evgenii Stepanov <eugenis@google.com>
Co-developed-by: Peter Collingbourne <pcc@google.com>
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20210521010023.3244784-1-eugenis@google.com
Signed-off-by: Will Deacon <will@kernel.org>
Semantics wise, [pud|pmd]_bad() have always implied that a given [PUD|PMD]
entry does not have a pointer to the next level page table. This had been
made clear in the commit a1c76574f3 ("arm64: mm: use *_sect to check for
section maps"). Hence explicitly check for a table entry rather than just
testing a single bit. This basically redefines [pud|pmd]_bad() in terms of
[pud|pmd]_table() making the semantics clear.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/1620644871-26280-1-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
CONFIG_PGTABLE_LEVELS has been statically defined in (arch/arm64/Kconfig)
depending on the page size and requested virtual address range. In order to
validate this page table levels selection this adds a BUILD_BUG_ON() as per
the existing formula ARM64_HW_PGTABLE_LEVELS(). This would help protect any
inadvertent changes to CONFIG_PGTABLE_LEVELS selection.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Link: https://lore.kernel.org/r/1620649326-24115-1-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Reliable stacktracing requires that we identify when a stacktrace is
terminated early. We can do this by ensuring all tasks have a final
frame record at a known location on their task stack, and checking
that this is the final frame record in the chain.
We'd like to use task_pt_regs(task)->stackframe as the final frame
record, as this is already setup upon exception entry from EL0. For
kernel tasks we need to consistently reserve the pt_regs and point x29
at this, which we can do with small changes to __primary_switched,
__secondary_switched, and copy_process().
Since the final frame record must be at a specific location, we must
create the final frame record in __primary_switched and
__secondary_switched rather than leaving this to start_kernel and
secondary_start_kernel. Thus, __primary_switched and
__secondary_switched will now show up in stacktraces for the idle tasks.
Since the final frame record is now identified by its location rather
than by its contents, we identify it at the start of unwind_frame(),
before we read any values from it.
External debuggers may terminate the stack trace when FP == 0. In the
pt_regs->stackframe, the PC is 0 as well. So, stack traces taken in the
debugger may print an extra record 0x0 at the end. While this is not
pretty, this does not do any harm. This is a small price to pay for
having reliable stack trace termination in the kernel. That said, gdb
does not show the extra record probably because it uses DWARF and not
frame pointers for stack traces.
Signed-off-by: Madhavan T. Venkataraman <madvenka@linux.microsoft.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
[Mark: rebase, use ASM_BUG(), update comments, update commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20210510110026.18061-1-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
There is a clock driver that's needed when using an external
USB reference clock called usb2_clksel.
Enable it in the defconfig.
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20210513114617.30191-3-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The RZ/G2 boards expect there to be an external clock reference for
USB2 EHCI controllers. For the Beacon boards, this reference clock
is controlled by a programmable versaclock. Because the RZ/G2
family has a special clock driver when using an external clock,
the third clock reference in the EHCI node needs to point to this
special clock, called usb2_clksel.
Since the usb2_clksel does not keep the usb_extal clock enabled,
the 4th clock entry for the EHCI nodes needs to reference it to
keep the clock running and make USB functional.
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20210513114617.30191-2-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The USB extal clock reference isn't associated to a crystal, it's
associated to a programmable clock, so remove the extal reference,
add the usb2_clksel. Since usb_extal is referenced by the versaclock,
reference it here so the usb2_clksel can get the proper clock speed
of 50MHz.
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20210513114617.30191-1-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The eMMC card has two supplies, VCC and VCCQ. The VCC supplies the NAND
array and the VCCQ supplies the bus. On Condor, the VCC is connected to
3.3V rail, while the VCCQ is connected to 1.8V rail. Adjust the pinmux
to match the bus, which is always operating in 1.8V mode.
While at it, deduplicate the pinmux entries, which are now the same for
both default and UHS modes. We still need the two pinctrl entries to
match the bindings though.
Thanks to Marek Vasut for this description from commit 5f65328df3
("arm64: dts: renesas: Switch eMMC bus to 1V8 on Salvator-X and ULCB").
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210419143858.39401-1-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The AVB reference clock assumes an external clock that runs
automatically. Because the Versaclock is wired to provide the
AVB refclock, the device tree needs to reference it in order for the
driver to start the clock.
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20210224115146.9131-5-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The bindings have been updated to support two clocks.
Add a clock-names list in the device tree with fck in it.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210224115146.9131-3-aford173@gmail.com
[geert: Update new r8a779a0.dtsi]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the "PinePhone" name to the sound card: this will make
upstreaming an ALSA UCM config easier as we can use a unique name.
It also avoids an issue where the default card name is truncated.
Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
[Samuel: Split out change, updated commit message]
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210430035859.3487-8-samuel@sholland.org
During hardware validation it was noticed that the clock isn't
continuously enabled when there is no link. This is because the 125MHz
clock is derived from the internal PLL which seems to go into some kind
of power-down mode every once in a while. The LS1028A expects a contiuous
clock. Thus enable the PLL all the time.
Also, the RGMII pad voltage is wrong, it was configured to 2.5V (that is
the VDDH regulator). The correct voltage is 1.8V, i.e. the VDDIO
regulator.
This fix is for the freescale/fsl-ls1028a-kontron-sl28-var1.dts.
Fixes: 642856097c ("arm64: dts: freescale: sl28: add variant 1")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
During hardware validation it was noticed that the clock isn't
continuously enabled when there is no link. This is because the 125MHz
clock is derived from the internal PLL which seems to go into some kind
of power-down mode every once in a while. The LS1028A expects a contiuous
clock. Thus enable the PLL all the time.
Also, the RGMII pad voltage is wrong. It was configured to 2.5V (that is
the VDDH regulator). The correct voltage is 1.8V, i.e. the VDDIO
regulator.
This fix is for the freescale/fsl-ls1028a-kontron-sl28-var4.dts.
Fixes: 815364d042 ("arm64: dts: freescale: add Kontron sl28 support")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As this is a fixed regulator on the board there was no harm in the wrong
voltage being specified, apart from a confusing reporting to userspace.
Fixes: 4a13b3bec3 ("arm64: dts: imx: add Zii Ultra board support")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
When adding the sound support a second instance of the GEN_3V3 regulator was
added by accident. Remove it and point the consumers to the first instance.
Fixes: 663a5b5efa ("arm64: dts: zii-ultra: add sound support")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Most Layerscape SoCs support ECC error reporting for the memory
controller. Enable the corresponding module. In particular, this will
enable EDAC support on the Kontron sl28 board which comes with ECC
memory.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
While enabling EDAC support for the LS1028A it was discovered that the
memory node has a wrong endianness setting as well as a wrong interrupt
assignment. Fix both.
This was tested on a sl28 board. To force ECC errors, you can use the
error injection supported by the controller in hardware (with
CONFIG_EDAC_DEBUG enabled):
# enable error injection
$ echo 0x100 > /sys/devices/system/edac/mc/mc0/inject_ctrl
# flip lowest bit of the data
$ echo 0x1 > /sys/devices/system/edac/mc/mc0/inject_data_lo
Fixes: 8897f3255c ("arm64: dts: Add support for NXP LS1028A SoC")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There are no sub-mailbox devices defined currently for both the
IOT2050 boards. These are usually dictated by the firmwares running
on the R5F remote processors and the applications they provide.
Defining the actual sub-mailboxes will also dictate the interrupts
the clusters will use for interrupts on the Cortex-A53 cores.
Disable all of the Mailbox clusters until the sub-mailboxes are
defined and used. This fixes the warnings around the missing
interrupts with the upcoming conversion of the OMAP Mailbox binding
to YAML format.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210514212016.3153-1-s-anna@ti.com
Only a small number of fixes so far, including some that I had applied
during the merge window, so this is based on the original merge of the
other branches.
- The largest change is a fix for a reference counting bug in
the AMD TEE driver.
- Neil Armstrong now co-maintains Amlogic SoC support
- Two build warning fixes for renesas device tree files
- A sign expansion bug for optee
- A DT binding fix for a mismerge
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=w6Zu
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-fixes-5.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"Only a small number of fixes so far, including some that I had applied
during the merge window, so this is based on the original merge of the
other branches.
- The largest change is a fix for a reference counting bug in the AMD
TEE driver.
- Neil Armstrong now co-maintains Amlogic SoC support
- Two build warning fixes for renesas device tree files
- A sign expansion bug for optee
- A DT binding fix for a mismerge"
* tag 'arm-soc-fixes-5.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: npcm: wpcm450: select interrupt controller driver
MAINTAINERS: ARM/Amlogic SoCs: add Neil as primary maintainer
tee: amdtee: unload TA only when its refcount becomes 0
dt-bindings: nvmem: mediatek: remove duplicate mt8192 line
firmware: arm_scmi: Remove duplicate declaration of struct scmi_protocol_handle
firmware: arm_scpi: Prevent the ternary sign expansion bug
arm64: dts: renesas: Add port@0 node for all CSI-2 nodes to dtsi
arm64: dts: renesas: aistarvision-mipi-adapter-2.1: Fix CSI40 ports
Randy reported a randconfig build error recently on i386:
ld: arch/x86/net/bpf_jit_comp32.o: in function `do_jit':
bpf_jit_comp32.c:(.text+0x28c9): undefined reference to `__bpf_call_base'
ld: arch/x86/net/bpf_jit_comp32.o: in function `bpf_int_jit_compile':
bpf_jit_comp32.c:(.text+0x3694): undefined reference to `bpf_jit_blind_constants'
ld: bpf_jit_comp32.c:(.text+0x3719): undefined reference to `bpf_jit_binary_free'
ld: bpf_jit_comp32.c:(.text+0x3745): undefined reference to `bpf_jit_binary_alloc'
ld: bpf_jit_comp32.c:(.text+0x37d3): undefined reference to `bpf_jit_prog_release_other'
[...]
The cause was that b24abcff91 ("bpf, kconfig: Add consolidated menu entry for
bpf with core options") moved BPF_JIT from net/Kconfig into kernel/bpf/Kconfig
and previously BPF_JIT was guarded by a 'if NET'. However, there is no actual
dependency on NET, it's just that menuconfig NET selects BPF. And the latter in
turn causes kernel/bpf/core.o to be built which contains above symbols. Randy's
randconfig didn't have NET set, and BPF wasn't either, but BPF_JIT otoh was.
Detangle this by making BPF_JIT depend on BPF instead. arm64 was the only arch
that pulled in its JIT in net/ via obj-$(CONFIG_NET), all others unconditionally
pull this dir in via obj-y. Do the same since CONFIG_NET guard there is really
useless as we compiled the JIT via obj-$(CONFIG_BPF_JIT) += bpf_jit_comp.o anyway.
Fixes: b24abcff91 ("bpf, kconfig: Add consolidated menu entry for bpf with core options")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Change the node name of the UART devices to match
"^serial(@[0-9a-f,]+)*$".
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEq1nRK9aeMoq1VSgcnJ2qBz9kQNkFAmCmN9AACgkQnJ2qBz9k
QNn5ZwgAwnLdgBuILDqJwPaYpXOzvMhjjG8AwBDzhMYhhpt+OOCUevoRm7mDU7J2
t/DlwWGMhpp80ku+x+AURR/ltOfFvw4QAHeIXPWjkoieFKcLOEvAjWWZP6oIFC12
5e/QVXqK58fuRJwveYp4jZ+AXvDMoHJrDXsoTFezjBDIQQgzlIlrMzPavS/6UzUN
mAF2sapE9lcQoRMfU8kktBWPVM/GpFkus2Q48EYFCZ1rp3aRyw/aahTVuvSUZCV0
XiY6f2F7qgFLtomK6UurlxTc7rPsrG+UmNvGWuXf3R81UawegmKQeG5zcaMGrZs1
kHyJQcP9nGYPLDXt/4kW9cY0s8oOKg==
=RbOE
-----END PGP SIGNATURE-----
Merge tag 'quota_for_v5.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull quota fixes from Jan Kara:
"The most important part in the pull is disablement of the new syscall
quotactl_path() which was added in rc1.
The reason is some people at LWN discussion pointed out dirfd would be
useful for this path based syscall and Christian Brauner agreed.
Without dirfd it may be indeed problematic for containers. So let's
just disable the syscall for now when it doesn't have users yet so
that we have more time to mull over how to best specify the filesystem
we want to work on"
* tag 'quota_for_v5.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
quota: Disable quotactl_path syscall
quota: Use 'hlist_for_each_entry' to simplify code
Alexei Starovoitov says:
====================
pull-request: bpf-next 2021-05-19
The following pull-request contains BPF updates for your *net-next* tree.
We've added 43 non-merge commits during the last 11 day(s) which contain
a total of 74 files changed, 3717 insertions(+), 578 deletions(-).
The main changes are:
1) syscall program type, fd array, and light skeleton, from Alexei.
2) Stop emitting static variables in skeleton, from Andrii.
3) Low level tc-bpf api, from Kumar.
4) Reduce verifier kmalloc/kfree churn, from Lorenz.
====================
The NanoPi R1S H5 is a open source board made by FriendlyElec.
It has the following features:
- Allwinner H5, Quad-core Cortex-A53
- 512MB DDR3 RAM
- 10/100/1000M Ethernet x 2
- RTL8189ETV WiFi 802.11b/g/n
- USB 2.0 host port (A)
- MicroSD Slot
- Serial Debug Port
- 5V 2A DC power-supply
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210516163523.9484-2-amadeus@jmu.edu.cn
After commit 96a71005bd ("bpf, arm64: remove obsolete exception handling
from div/mod"), there is no need to check twice about BPF_DIV and BPF_MOD,
remove the redundant switch case.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/1621328170-17583-1-git-send-email-yangtiezhu@loongson.cn
With infradead.org archives gone, update the link to lore.kernel.org as
these links are deemed stable.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In commit fa8b90070a ("quota: wire up quotactl_path") we have wired up
new quotactl_path syscall. However some people in LWN discussion have
objected that the path based syscall is missing dirfd and flags argument
which is mostly standard for contemporary path based syscalls. Indeed
they have a point and after a discussion with Christian Brauner and
Sascha Hauer I've decided to disable the syscall for now and update its
API. Since there is no userspace currently using that syscall and it
hasn't been released in any major release, we should be fine.
CC: Christian Brauner <christian.brauner@ubuntu.com>
CC: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/lkml/20210512153621.n5u43jsytbik4yze@wittgenstein
Signed-off-by: Jan Kara <jack@suse.cz>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCYKC7SQAKCRCAXGG7T9hj
vpmTAQCmz5LvFHN9eAfq5jwz4cMvrN5h8aWnZjChgiAFZl0T7wD/TEDjtK18piUM
xWjZDUefMonnk0U8+bPityDmt8UV2AI=
=KFFw
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.13b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- two patches for error path fixes
- a small series for fixing a regression with swiotlb with Xen on Arm
* tag 'for-linus-5.13b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/swiotlb: check if the swiotlb has already been initialized
arm64: do not set SWIOTLB_NO_FORCE when swiotlb is required
xen/arm: move xen_swiotlb_detect to arm/swiotlb-xen.h
xen/unpopulated-alloc: fix error return code in fill_list()
xen/gntdev: fix gntdev_mmap() error exit path
Commit 03fdfb2690 ("KVM: arm64: Don't write junk to sysregs on
reset") flipped the register number to 0 for all the debug registers
in the sysreg table, hereby indicating that these registers live
in a separate shadow structure.
However, the author of this patch failed to realise that all the
accessors are using that particular index instead of the register
encoding, resulting in all the registers hitting index 0. Not quite
a valid implementation of the architecture...
Address the issue by fixing all the accessors to use the CRm field
of the encoding, which contains the debug register index.
Fixes: 03fdfb2690 ("KVM: arm64: Don't write junk to sysregs on reset")
Reported-by: Ricardo Koller <ricarkol@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
KVM currently updates PC (and the corresponding exception state)
using a two phase approach: first by setting a set of flags,
then by converting these flags into a state update when the vcpu
is about to enter the guest.
However, this creates a disconnect with userspace if the vcpu thread
returns there with any exception/PC flag set. In this case, the exposed
context is wrong, as userspace doesn't have access to these flags
(they aren't architectural). It also means that these flags are
preserved across a reset, which isn't expected.
To solve this problem, force an explicit synchronisation of the
exception state on vcpu exit to userspace. As an optimisation
for nVHE systems, only perform this when there is something pending.
Reported-by: Zenghui Yu <yuzenghui@huawei.com>
Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Tested-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org # 5.11
In order to make it easy to call __adjust_pc() from the EL1 code
(in the case of nVHE), rename it to __kvm_adjust_pc() and move
it out of line.
No expected functional change.
Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Tested-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org # 5.11
The host stage-2 memory pools are not used outside of mem_protect.c,
mark them static.
Fixes: 1025c8c0c6 ("KVM: arm64: Wrap the host with a stage 2")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Quentin Perret <qperret@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210514085640.3917886-3-qperret@google.com
It is not used outside of setup.c, mark it static.
Fixes:f320bc742bc2 ("KVM: arm64: Prepare the creation of s1 mappings at EL2")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Quentin Perret <qperret@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210514085640.3917886-2-qperret@google.com
arch/arm64/kvm/mmu.c:1114:9-10: WARNING: return of 0/1 in function 'kvm_age_gfn' with return type bool
arch/arm64/kvm/mmu.c:1084:9-10: WARNING: return of 0/1 in function 'kvm_set_spte_gfn' with return type bool
arch/arm64/kvm/mmu.c:1127:9-10: WARNING: return of 0/1 in function 'kvm_test_age_gfn' with return type bool
arch/arm64/kvm/mmu.c:1070:9-10: WARNING: return of 0/1 in function 'kvm_unmap_gfn_range' with return type bool
Return statements in functions returning bool should use
true/false instead of 1/0.
Generated by: scripts/coccinelle/misc/boolreturn.cocci
Fixes: cd4c718352 ("KVM: arm64: Convert to the gfn-based MMU notifier callbacks")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: kernel test robot <lkp@intel.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210426223357.GA45871@cd4295a34ed8
The RK3308 SoC has a gmac with only the RMII interface exposed. This
commit adds it to the RK3308 dtsi.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interrupt routers are memory mapped peripherals, that are organized
in our dts bus hierarchy to closely represents the actual hardware
behavior.
However, without explicitly calling out the reg property, using
2021.03+ dt-schema package, this exposes the following problem with
dtbs_check:
/arch/arm64/boot/dts/ti/k3-am654-base-board.dt.yaml: bus@100000:
interrupt-controller0: {'type': 'object'} is not allowed for
{'compatible': ['ti,sci-intr'], .....
Even though we don't use interrupt router directly via memory mapped
registers and have to use it via the system controller, the hardware
block is memory mapped, so describe the base address in device tree.
This is a valid, comprehensive description of hardware and permitted
by the existing ti,sci-intr schema.
Reviewed-by: Tero Kristo <kristo@kernel.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210511194821.13919-1-nm@ti.com
Instead of using empty ranges property, lets map explicitly the address
range that is mapped onto the dma / navigator subsystems (navss/dmss).
This is also exposed via the dtbs_check with dt-schema newer than
2021.03 version by throwing out following:
arch/arm64/boot/dts/ti/k3-am654-base-board.dt.yaml: bus@100000: main-navss:
{'type': 'object'} is not allowed for
{'compatible': ['simple-mfd'], '#address-cells': [[2]], .....
This has already been correctly done for J7200, however was missed for
other k3 SoCs. Fix that oversight.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tero Kristo <kristo@kernel.org>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20210510145429.8752-1-nm@ti.com
Lets rename the node name of TI-SCI node to be system-controller as it
is a better standardized name for the function that TI-SCI plays in the
SoC.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tero Kristo <kristo@kernel.org>
Link: https://lore.kernel.org/r/20210510145033.7426-5-nm@ti.com
The DMSC node does'nt require any of "#address-cells", "#size-cells"
or "ranges" property as the child nodes are representations of SoC's
system controller itself, so align it with the bindings.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tero Kristo <kristo@kernel.org>
Link: https://lore.kernel.org/r/20210510145033.7426-4-nm@ti.com
We currently use clocks as the node name for the node representing
TI-SCI clock nodes. This is better renamed to being clock-controller
as that is a better representative of the system controller function
as a clock controller for the SoC.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tero Kristo <kristo@kernel.org>
Link: https://lore.kernel.org/r/20210510145033.7426-2-nm@ti.com
Traffic through main NAVSS interconnect is coherent wrt ARM caches on
J7200 SoC. Add missing dma-coherent property to main_navss node.
Also add dma-ranges to be consistent with mcu_navss node
and with AM65/J721e main_navss and mcu_navss nodes.
Fixes: d361ed8845 ("arm64: dts: ti: Add support for J7200 SoC")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210510180601.19458-1-vigneshr@ti.com
AM654 EVM boards are not shipped with OV5640 sensor module, it is a
separate purchase. OV5640 module is also just one of the possible
sensors or capture boards you can connect.
However, for some reason, OV5640 has been added to the board dts file,
making it cumbersome to use other sensors.
Remove the OV5640 from the dts file so that it is easy to use other
sensors via DT overlays.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210423083120.73476-1-tomi.valkeinen@ideasonboard.com
To ensure that instructions are observable in a new mapping, the arm64
set_pte_at() implementation cleans the D-cache and invalidates the
I-cache to the PoU. As an optimisation, this is only done on executable
mappings and the PG_dcache_clean page flag is set to avoid future cache
maintenance on the same page.
When two different processes map the same page (e.g. private executable
file or shared mapping) there's a potential race on checking and setting
PG_dcache_clean via set_pte_at() -> __sync_icache_dcache(). While on the
fault paths the page is locked (PG_locked), mprotect() does not take the
page lock. The result is that one process may see the PG_dcache_clean
flag set but the I/D cache maintenance not yet performed.
Avoid test_and_set_bit(PG_dcache_clean) in favour of separate test_bit()
and set_bit(). In the rare event of a race, the cache maintenance is
done twice.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: <stable@vger.kernel.org>
Cc: Will Deacon <will@kernel.org>
Cc: Steven Price <steven.price@arm.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210514095001.13236-1-catalin.marinas@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
A test with the command below gives this error:
/arch/arm64/boot/dts/rockchip/rk3328-a1.dt.yaml: syscon@ff100000:
grf-gpio: {'compatible': ['rockchip,rk3328-grf-gpio'],
'gpio-controller': True, '#gpio-cells': [[2]], 'phandle': [[68]]} is not
of type 'array'
Due to the regex "(?<!,nr)-gpios?$" anything that ends on
'-gpio', '-gpios' gives a match.
Rename 'grf-gpio' nodename to generic 'gpio'
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/
schemas/gpio/gpio-consumer.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210512122346.9463-5-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Although SWIOTLB_NO_FORCE is meant to allow later calls to swiotlb_init,
today dma_direct_map_page returns error if SWIOTLB_NO_FORCE.
For now, without a larger overhaul of SWIOTLB_NO_FORCE, the best we can
do is to avoid setting SWIOTLB_NO_FORCE in mem_init when we know that it
is going to be required later (e.g. Xen requires it).
CC: boris.ostrovsky@oracle.com
CC: jgross@suse.com
CC: catalin.marinas@arm.com
CC: will@kernel.org
CC: linux-arm-kernel@lists.infradead.org
Fixes: 2726bf3ff2 ("swiotlb: Make SWIOTLB_NO_FORCE perform no allocation")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Stefano Stabellini <stefano.stabellini@xilinx.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20210512201823.1963-2-sstabellini@kernel.org
Signed-off-by: Juergen Gross <jgross@suse.com>
This is enough to make the SATA controller visible:
# lspci
00:00.0 PCI bridge: Fuzhou Rockchip Electronics Co., Ltd RK3399 PCI Express Root Port
01:00.0 SATA controller: JMicron Technology Corp. JMB58x AHCI SATA controller
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Link: https://lore.kernel.org/r/20210510090932.970447-1-uwe@kleine-koenig.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
On the helios64 board the two connectors P6 and P7 are supposed to
power two fans. Add the corresponding pwm-fan devices.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Link: https://lore.kernel.org/r/20210510090607.970145-1-uwe@kleine-koenig.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives this error:
/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dt.yaml:
sdmmcio-regulator: states:0:
[1800000, 1, 3300000, 0] is too long
dtbs_check expects regulator-gpio states in a format
of 2 per item, so fix them all.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/
regulator/gpio-regulator.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210510215840.16270-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Unify similar build rules.
sha256-core.S opts out it because it is generated from sha512-armv8.pl.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Generate *.S by Perl like arch/{mips,x86}/crypto/Makefile.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Enable the MMC_MTK option necessary to boot Mediatek boards from the
mmc. Booting from the mmc is the common method used for a bunch of
boards, specially Chromebooks, to boot from. Hence this driver is
built-in.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20210423075250.2616275-1-enric.balletbo@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Commit 'fbbe38309d56 ("arm64: defconfig: Allow mt8173-based boards to boot
from usb")' added the MTK_PMIC_WRAP config built-in. It needs to be
built-in in order to be able to boot from USB or the MMC without needing
a ramdisk, but that symbol was already defined as a module so now we are
getting the following warning:
arch/arm64/configs/defconfig:996:warning: override: reassigning to symbol MTK_PMIC_WRAP
Remove the MTK_PMIC_WRAP=m from the defconfig to remove the error.
Fixes: fbbe38309d ("arm64: defconfig: Allow mt8173-based boards to boot from usb")
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20210423075201.2616023-1-enric.balletbo@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Use the common function round_up() directly to show the align size
explicitly, the function STACK_ALIGN() is needless, remove it. Other
JITs also just rely on round_up().
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/1620651119-5663-1-git-send-email-yangtiezhu@loongson.cn
Odelu Kukatla
Stephan Gerhold
Stephen Boyd
Srinivasa Rao Mandadapu
Wenchao Han
Lad Prabhakar
Icenowy Zheng
Florian Fainelli
Nicolas Boichat
Sudeep Holla
Michael Kao
Ikjoon Jang
Stefan Wahren
Mark Rutland
Kishon Vijay Abraham I
Mark Brown
Sameer Pujar
Eric Anholt
Suman Anna
Roger Quadros
Aswath Govindraju
Jan Kara
Geert Uytterhoeven
Linus Torvalds
Marc Zyngier
Felipe Balbi
Alex Elder
Sujit Kautkar
Michael Srba
Matthias Kaehlcke
Olof Johansson
Peter Collingbourne
Kefeng Wang
Ingo Molnar
Naveen N. Rao
Tobias Schramm
Johan Jonker
Shaokun Zhang
Chris Morgan
Alim Akhtar
Hsin-Yi Wang
Will Deacon
Robin Murphy
Sam Tebbs
Judy Hsiao
Peter Zijlstra
Tian Tao
Keqian Zhu
Neil Armstrong
Rajendra Nayak
Sibi Sankar
Taniya Das
Douglas Anderson
Jonathan Marek
Serge Semin
Petr Vorel
Konrad Dybcio
Loic Poulain
Roja Rani Yarubandi
Vinod Koul
Vincent Knecht
Robert Marko
Jerome Brunet
Grygorii Strashko
Thierry Reding
Jon Hunter
Jakub Kicinski
Julien Thierry
Zenghui Yu
Catalin Marinas
Masahiro Yamada
satya priya
Rajeshwari Ravindra Kamble
Yassine Oudjana
Gokul Sriram Palanisamy
Sergey Senozhatsky
Joel Selvaraj
Caleb Connolly
Harigovindan P
Fuad Tabba
Anshuman Khandual
Evgenii Stepanov
Madhavan T. Venkataraman
Jisheng Zhang
Adam Ford
Valentine Barshak
Wolfram Sang
Niklas Söderlund
Arnaud Ferraris
Michael Walle
Lucas Stach
Daniel Borkmann
Zhen Lei
David S. Miller
Chukun Pan
Tiezhu Yang
Quentin Perret
kernel test robot
Nishanth Menon
Vignesh Raghavendra
Tomi Valkeinen
Christoph Hellwig
Uwe Kleine-König
Enric Balletbo i Serra
Adrien Grassein