Add initial support for big endian by always writing the pte
in le32. Note, revisit if hardware capable of doing big endian
fetches.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Register iommu_ops at the end of successful probe instead of doing that
unconditionally. This makes Exynos IOMMU driver ready for deferred probe
caused by not-yet-available clocks.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Make clock preparation together with clk_enable(). This way inactive
SYSMMU controllers will not keep clocks prepared all the time.
This change allows more fine graded power management in the future.
All the code assumes that clock management doesn't fail, so guard
clock_prepare_enable() it with BUG_ON().
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
If SYSMMU controller is not active, there is no point in enabling master's
clock just for doing the the of internal state. This patch moves enabling
that clock to the block which actually does the register access.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This patch reworks driver probe code to propagate error codes from
clk_get() operation. This will allow to properly handle deferred probe
in the future.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Removal of IOMMU driver cannot be done reliably, so Exynos IOMMU driver
doesn't support this operation. It is essential for system operation, so
it makes sense to prevent unbinding by disabling bind/unbind sysfs
feature for SYSMMU controller driver to avoid kernel ops or trashing
memory caused by such operation.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: stable@vger.kernel.org # v4.2+
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Drivers should use generic readl/writel calls to access HW registers, so
replace all __raw_readl/writel with generic version.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The exynos iommu driver changed an incorrect cast from pointer
to 'unsigned int' to an equally incorrect cast to a 'phys_addr_t',
which results in an obvious compile-time error when phys_addr_t
is wider than pointers are:
drivers/iommu/exynos-iommu.c: In function 'alloc_lv2entry':
drivers/iommu/exynos-iommu.c:918:32: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
The code does not actually want the physical address (which would
involve using virt_to_phys()), but just checks the alignment,
so we can change it to use a cast to uintptr_t instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 740a01eee9 ("iommu/exynos: Add support for v5 SYSMMU")
Signed-off-by: Joerg Roedel <jroedel@suse.de>
IOMMU core calls attach_device callback without detaching device from
the previous domain. This patch adds support for such unballanced calls.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This patch adds support for v5 of SYSMMU controller, found in Samsung
Exynos 5433 SoCs. The main difference of v5 is support for 36-bit physical
address space and some changes in register layout and core clocks hanging.
This patch also adds support for ARM64 architecture, which is used by
Exynos 5433 SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
SYSMMU on some SoCs reports bogus values in VERSION register. Force
hardware version to 1.0 for such controllers. This patch also moves reading
version register to driver's probe() function.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This patch simplifies the code for handling of flpdcache invalidation.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This patch rewrites sysmmu_init_config function to make it easier to read
and understand.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This patch provides a new implementation for page fault handing code. The
new implementation is ready for future extensions. No functional changes
have been made.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This patch changes some internal functions to have access to the state of
sysmmu device instead of having only it's registers. This will make the
code ready for future extensions.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
All clock API function can be called on NULL clock, so simplify code avoid
checking of master clock presence.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This patch replaces custom ARM-specific code for performing CPU cache flush
operations with generic code based on DMA-mapping. Domain managing code
is independent of particular SYSMMU device, so the first registered SYSMMU
device is used for DMA-mapping calls. This simplification works fine
because all SYSMMU controllers are in the same address space (where
DMA address equals physical address) and the DMA-mapping calls are done
mainly to flush CPU cache to make changes visible to SYSMMU controllers.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This patch adds support for DMA domain type. Such domain have DMA cookie
prepared and can be used by generic DMA-IOMMU glue layer.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This patch replaces custom code in add_device implementation with
iommu_group_get_for_dev() call and provides the needed callback.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This patch adds implementation of of_xlate callback, which prepares
masters device for attaching to IOMMU. This callback is called during
creating devices from device tree.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This patch introduces IOMMU_OF_DECLARE-based initialization to the
driver, which replaces subsys_initcall-based procedure.
exynos_iommu_of_setup ensures that each sysmmu controller is probed
before its master device.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
When system goes into suspend state, iommu should save it's state and
restore after system resume. This is handled by 'late' pm ops to ensure
that sysmmu will be suspended after its master devices and restored
before them.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This patch fixes support for runtime power management for SYSMMU
controllers, so they are enabled when master device is attached.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This patch adds support for assigning more than one SYSMMU controller to
the master device. This has been achieved simply by chaning the struct
device pointer in struct exynos_iommu_owner into the list of struct
sysmmu_drvdata of all controllers assigned to the given master device.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Return fail if given master device passed to add_device/remove_device
callbacks doesn't has associated any sysmmu controller.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Add a few words of comment to all internal structures used by the driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Replace all remaining usage of struct iommu_domain with struct
exynos_iommu_domain in all internal structures and functions.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This patch renames some variables to make the code easier to understand.
'domain' is replaced by 'iommu_domain' (more generic entity) and really
meaningless 'priv' by 'domain' to reflect its purpose.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This patch simplifies the code by:
- refactoring function parameters from struct device pointer to direct
pointer to struct sysmmu drvdata
- moving list_head enteries from struct exynos_iommu_owner directly to
struct sysmmu_drvdata
After above refactoring some functions were never used, so remove also
them completely.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This patch removes useless spinlocks and other unused members from
struct exynos_iommu_owner. There is no point is protecting this
structure by spinlock because content of this structure doesn't change
and other structures have their own spinlocks.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This patch removes two unneeded functions, which are not a part of
generic IOMMU API and were never used by any other driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This patch removes reading of REG_MMU_VERSION register on every tlb
operation and caches SYSMMU version in driver's internal data.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The pointers to the 2nd level page tables are converted to 1st level
page table entries, which means kmemleak can't find them and assumes
they have been leaked. Call kmemleak_ignore on the 2nd level page
tables to prevent them from showing up in kmemleak reports.
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The Exynos System MMU driver unconditionally executes code and registers
a struct iommu_ops with the platform bus irrespective of whether it runs
on an Exynos SoC or not. This causes problems in multi-platform kernels
where drivers for other SoCs will no longer be able to register their
own struct iommu_ops or even try to use a struct iommu_ops for an IOMMU
that obviously isn't there.
The smallest fix I could think of is to check for the existence of any
Exynos System MMU devices in the device tree and skip initialization
otherwise.
This fixes a problem on Tegra20 where the DRM driver will try to use the
obviously non-existent Exynos System MMU.
Reported-by: Nicolas Chauvet <kwizart@gmail.com>
Cc: Kukjin Kim <kgene@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Mapping and unmapping are more often than not in the critical path.
map_sg allows IOMMU driver implementations to optimize the process
of mapping buffers into the IOMMU page tables.
Instead of mapping a buffer one page at a time and requiring potentially
expensive TLB operations for each page, this function allows the driver
to map all pages in one go and defer TLB maintenance until after all
pages have been mapped.
Additionally, the mapping operation would be faster in general since
clients does not have to keep calling map API over and over again for
each physically contiguous chunk of memory that needs to be mapped to a
virtually contiguous region.
Signed-off-by: Olav Haugan <ohaugan@codeaurora.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This structure is read-only data and should never be modified.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Silences the following type of warnings:
WARNING: Missing a blank line after declarations
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This patch contains 2 workaround for the System MMU v3.x.
System MMU v3.2 and v3.3 has FLPD cache that caches first level page
table entries to reduce page table walking latency. However, the
FLPD cache is filled with a first level page table entry even though
it is not accessed by a master H/W because System MMU v3.3
speculatively prefetches page table entries that may be accessed
in the near future by the master H/W.
The prefetched FLPD cache entries are not invalidated by iommu_unmap()
because iommu_unmap() only unmaps and invalidates the page table
entries that is mapped.
Because exynos-iommu driver discards a second level page table when
it needs to be replaced with another second level page table or
a first level page table entry with 1MB mapping, It is required to
invalidate FLPD cache that may contain the first level page table
entry that points to the second level page table.
Another workaround of System MMU v3.3 is initializing the first level
page table entries with the second level page table which is filled
with all zeros. This prevents System MMU prefetches 'fault' first
level page table entry which may lead page fault on access to 16MiB
wide.
System MMU 3.x fetches consecutive page table entries by a page
table walking to maximize bus utilization and to minimize TLB miss
panelty.
Unfortunately, functional problem is raised with the fetching behavior
because it fetches 'fault' page table entries that specifies no
translation information and that a valid translation information will
be written to in the near future. The logic in the System MMU generates
page fault with the cached fault entries that is no longer coherent
with the page table which is updated.
There is another workaround that must be implemented by I/O virtual
memory manager: any two consecutive I/O virtual memory area must have
a hole between the two that is larger than or equal to 128KiB.
Also, next I/O virtual memory area must be started from the next
128KiB boundary.
0 128K 256K 384K 512K
|-------------|---------------|-----------------|----------------|
|area1---------------->|.........hole...........|<--- area2 -----
The constraint is depicted above.
The size is selected by the calculation followed:
- System MMU can fetch consecutive 64 page table entries at once
64 * 4KiB = 256KiB. This is the size between 128K ~ 384K of the
above picture. This style of fetching is 'block fetch'. It fetches
the page table entries predefined consecutive page table entries
including the entry that is the reason of the page table walking.
- System MMU can prefetch upto consecutive 32 page table entries.
This is the size between 256K ~ 384K.
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This turns on FLPD_CACHE, ACGEN and SYSSEL.
FLPD_CACHE is a cache of 1st level page table entries that contains
the address of a 2nd level page table to reduce latency of page table
walking.
ACGEN is architectural clock gating that gates clocks by System MMU
itself if it is not active. Note that ACGEN is different from clock
gating by the CPU. ACGEN just gates clocks to the internal logic of
System MMU while clock gating by the CPU gates clocks to the System
MMU.
SYSSEL selects System MMU version in some Exynos SoCs. Some Exynos
SoCs have an option to select System MMU versions exclusively because
the SoCs adopts new System MMU version experimentally.
This also always selects LRU as TLB replacement policy. Selecting TLB
replacement policy is deprecated from System MMU 3.2. TLB in System
MMU 3.3 has single TLB replacement policy, LRU. The bit of MMU_CFG
selecting TLB replacement policy is remained as reserved.
QoS value of page table walking is set to 15 (highst value). System
MMU 3.3 can inherit QoS value of page table walking from its master
H/W's transaction. This new feature is enabled by default and QoS
value written to MMU_CFG is ignored.
This patch also adds simplifies the sysmmu version checking by
introducing some macros.
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This commit adds device tree support for System MMU.
Also, system mmu handling is improved. Previously, an IOMMU domain is
bound to a System MMU which is not correct. This patch binds an IOMMU
domain with the master device of a System MMU.
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Some redundant error message is removed and some error messages
are changed to error level from debug level.
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Patch written by Antonios Motakis <a.motakis@virtualopensystems.com>:
IOMMU groups are expected by certain users of the IOMMU API,
e.g. VFIO. Since each device is behind its own System MMU, we
can allocate a new IOMMU group for each device.
Reviewed-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Antonios Motakis <a.motakis@virtualopensystems.com>
Signed-off-by: Shaik Ameeer Basha <shaik.ameer@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This commit introduces sysmmu_pte_t for page table entries and
sysmmu_iova_t vor I/O virtual address that is manipulated by
exynos-iommu driver. The purpose of the typedef is to remove
dependencies to the driver code from the change of CPU architecture
from 32 bit to 64 bit.
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Since acquiring read_lock is not more frequent than write_lock, it is
not beneficial to use rwlock, this commit changes rwlock to spinlock.
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Ben Dooks
Marek Szyprowski
Arnd Bergmann
Colin Cross
Joerg Roedel
Thierry Reding
Linus Torvalds
Olav Haugan
Wolfram Sang
Sachin Kamat
Sachin Kamat
Bjorn Helgaas
Cho KyongHo
Antonios Motakis