The CPUs on Qualcomm MSM8916-based platforms are clocked by two PLLs,
a primary (A53) CPU PLL and a secondary fixed-rate GPLL0. These sources
are connected to a mux and half-integer divider, which is feeding the
CPU cores.
This patch adds support for the primary CPU PLL which generates the
higher range of frequencies above 1GHz.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
[sboyd@codeaurora.org: Move to devm provider registration,
NUL terminate frequency table, made tristate/modular]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
divider_recalc_rate() is an helper function used by clock divider of
different types, so the structure containing the 'hw' pointer is not
always a 'struct clk_divider'
At the following line:
> div = _get_div(table, val, flags, divider->width);
in several cases, the value of 'divider->width' is garbage as the actual
structure behind this memory is not a 'struct clk_divider'
Fortunately, this width value is used by _get_val() only when
CLK_DIVIDER_MAX_AT_ZERO flag is set. This has never been the case so
far when the structure is not a 'struct clk_divider'. This is probably
why we did not notice this bug before
Fixes: afe76c8fd0 ("clk: allow a clk divider with max divisor when zero")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
PCIE and NSS has MISC reset register in which single register has
multiple reset bit. The patch adds these resets with its
corresponding reset bits.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
- It has 3 general purpose clock controller which supplies
the clock in GPIO pins.
- It has Crypto Engine which has AXI, AHB and Core clocks.
Other non APSS processors can also use Crypto Engine so
these clocks are marked as VOTED clocks.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
IPQ8074 has 6 ethernet ports which supports all ethernet speeds
from 10Mpbs to 10 Gpbs and each speed requires different clock
rates. Each port has separate TX and RX clocks. These clocks
use separate external UNIPHY PLL’s which will be registered with
separate NSS driver. The clock frequency is 125 Mhz for UNIPHY0
and 312.5 Mhz for UNIPHY1 and UNIPHY2.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
IPQ8074 has NSS (Network Switching System) which has 2 UBI cores
and hardware crypto engine. Some clocks are separate for each UBI
core and remaining NSS clocks are common. The BIAS_PLL (300 Mhz)
and BIAS_PLL_NSS_NOC (416.5 Mhz) are external fixed clocks and
will be registered from dtsi or NSS driver.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
- It has 2 instances of PCIE which uses AXI, AHB, AUX, SYS NOC
AXI and PIPE clocks.
- It has 2 instances of USB 3.0 which uses AUX, SLEEP, PIPE,
SYS NOC, mock UTMI and master clocks.
- It has 2 instances of SDCC which uses APSS and AHB clock.
SDCC1 requires ICE core clock also.
- All the PIPE clocks are external clocks which will be
registered in clock framework by PHY drivers. The enabling
and disabling of PIPE RCG clocks are dependent upon PHY
initialization sequence so BRANCH_HALT_DELAY flag is required for
these clocks.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
- GPLL2, GPLL4 and GPLL6 are general PLL clocks and parent
for all core peripherals.
- UBI PLL is mainly used by NSS (Network Switching System).
IPQ8074 has 2 instances of NSS UBI cores and UBI PLL will
be used to control the core frequency.
- NSS Crypto PLL is mainly used by NSS Crypto Engine which
supports the multiple cryptographic algorithm used in
Ethernet.
- IPQ8074 frequency plan does not require change in PLL post
dividers so marked the same as read-only.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
GPLL0 uses 4 bits post divider which should be specified
in clock driver structure.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Currently the driver assumes the register configuration value
is identical to its index in the parent map. This patch adds
the parent map field in regmap mux clock node which contains
the mapping of parent index with actual register configuration
value. If regmap node contains this parent map then the
configuration value will be taken from this
parent map instead of simply writing the index value.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some of the divider settings are preconfigured and should not
be changed by the clock framework during frequency change. This
patch adds the read-only divider operation for QCOM dividers
which is equivalent to generic divider operations in
'commit 79c6ab5095 ("clk: divider: add CLK_DIVIDER_READ_ONLY flag")'.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some of the divider settings are preconfigured and should not
be changed by the clock framework during frequency change. This
patch adds the read-only divider operation for QCOM alpha pll
post divider which is equivalent to generic divider operations in
'commit 79c6ab5095 ("clk: divider: add CLK_DIVIDER_READ_ONLY flag")'.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Current PLL driver only supports 4 bit PLL post divider so
modified the PLL divider operations to support 2 bit PLL
post divider.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The Brammo type of Alpha PLL doesn't allow configuration of a
VCO, but it does support dynamic update in which the frequency
can be changed dynamically without turning off the PLL.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The Huayra type Alpha PLL has a 16 bit alpha value, and
depending on the alpha_mode, the alpha value can be treated as
M/N value or as a two’s compliment number. This PLL supports
dynamic programming.
Since the decoding of alpha val and dynamic programming are
completely different from other Alpha PLLs we add separate
functions for Huayra PLLs.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some of the Alpha PLLs support dynamic update in which the
frequency can be changed dynamically without turning off the PLL.
This dynamic update requires the following sequence:
1. Write the desired values to L_VAL and ALPHA_VAL registers
2. Toggle pll_latch_input from low to high
3. Wait for pll_ack_latch to transition from low to high
The new L and alpha values have been latched. It may
take some time for the PLL to fully settle with these
new values.
4. Pull pll_latch_input low
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The current configuration does not fully configure PLL alpha mode
and values so this patch
1. Configures PLL_ALPHA_VAL_U for PLL which supports 40 bit alpha.
2. Adds alpha enable and alpha mode configuration support.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some of the Alpha PLLs (like Spark and Brammo) don't have a
CONFIG_CTL_U register. Add logic to detect when PLLs don't have
this second config register and skip programming it during PLL
initialization.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The alpha value calculation has been written for 40-bit alpha
values which doesn't work work properly for 16-bit ones. The
alpha value is calculated on the basis of ALPHA_BITWIDTH to make
the computation easy for 40 bit alpha. After calculating the 32
bit alpha, it is converted to 40 bit alpha by making lower bits
zero. But if actual alpha register width is less than
ALPHA_BITWIDTH, then the actual width can be used for
calculation. This also means, during the 40 bit alpha pll set
rate path, the lower alpha register is not configured
Change the code to calculate the rate and register values from
'alpha_width' instead of hard-coding it so that it can work for
the different widths that are supported.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Alpha PLL is a generic name used for QCOM PLLs which uses L and
Alpha values for configuring the integer and fractional part.
QCOM SoCs use different types of Alpha PLLs for which basic
software configuration part is common with following differences.
1. All these PLLs have the same basic registers like
PLL_MODE, L_VAL, ALPHA_VAL but some of the register offsets are
different between PLLs types.
2. The dynamic programming sequence is different in some
of the Alpha PLLs
3. Some of the PLLs don’t have 64 bit config control, 64 bit
user control, VCO configuration, etc.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds 12.288 MHz suport to codec digital clk, this clock.
Some external PA requires a 12.288 MHz to work.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch fixes missing mnd_width for codec_digital clk, this is now set to
8 inline with datasheet.
Fixes: 3966fab8b6 ("clk: qcom: Add MSM8916 Global Clock Controller support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
lpaif i2s clk rates in the freq table are not accurate enough
for I2S mclk. Fix the inaccurate ones and add few more clock
rates that are used in LPASS audio driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Clkdiv module provides a clock output on the PMIC with CXO as
the source. This clock can be routed through PMIC GPIOs. Add
a device driver to configure this clkdiv module.
Signed-off-by: Tirupathi Reddy <tirupath@codeaurora.org>
[sboyd: Simplified code and moved to devm clk provider APIs]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
large change that introduces runtime PM support to the clk framework. Now we
properly call runtime PM operations on the device providing a clk when the clk
is in use. This helps on SoCs where the clks provided by a device need
something to be powered on before using the clks, like power domains or
regulators. It also helps power those things down when clks aren't in use. The
other core change is a devm API addition for clk providers so we can get rid of
a bunch of clk driver remove functions that are just doing
of_clk_del_provider().
Outside of the core, we have the usual addition of clk drivers and smattering
of non-critical fixes to existing drivers. The biggest diff is support for
Mediatek MT2712 and MT7622 SoCs, but those patches really just add a bunch
of data.
By the way, we're trying something new here where we build the tree up with
topic branches. We plan to work this into our workflow so that we don't step
on each other's toes, and so the fixes branch can be merged on an as-needed
basis.
Core:
- Runtime PM support for clk providers
- devm API for of_clk_add_hw_provider()
New Drivers:
- Mediatek MT2712 and MT7622
- Renesas R-Car V3M SoC
Updates:
- Runtime PM support for Samsung exynos5433/exynos4412 providers
- Removal of clkdev aliases on Samsung SoCs
- Convert clk-gpio to use gpio descriptors
- Various driver cleanups to match kernel coding style
- Amlogic Video Processing Unit VPU and VAPB clks
- Sigma-delta modulation for Allwinner audio PLLs
- Allwinner A83t Display clks
- Support for the second display unit clock on Renesas RZ/G1E
- Suspend/resume support for Renesas R-Car Gen3 CPG/MSSR
- New clock ids for Rockchip rk3188 and rk3368 SoCs
- Various 'const' markings on clk_ops structures
- RPM clk support on Qualcomm MSM8996/MSM8660 SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABCAAGBQJaD3qRAAoJEK0CiJfG5JUlOLgQAKWekgG/IYgcPzPWDYfg8Hwr
sVVUK7+q7TVfbHsbYVikJuUaxutKZ0onnrYmOalTTyyxqL2E1/rYScnxdYHfcwX8
cyfHebRHsbh/Xg45ktwjzBkO49nwuppkpXd/V80GSBUZ+lsIVl5DUrrFAZdRUEdr
CEsAsF9tEWIl+0gqXYNuiKBV7QAYv5BUPrbJQf0PwL6jX0OAhLv+ukfN8BdmYsOb
rdoqhdgmyHkTuIMqsC/H2yP59aAKBse7wxIYebDiTdbPWfTkC9q927fTs4A02F6L
sHfLvCpfuB4rOjXy6LSd1gMGWIcjotZai+idHBqtNLLVz6exF1QpUCp+pZjEULbA
/Sx9lk8A3cYoa8pTu1NrrZbZX17iHkFswqMF3T20nhUN9+Ti597ZEbRcWDcoEZtw
v2NznOTJ7Mm2SrNHOvDklstggNIGcwiAEePGMo7rJNEQZChpDjQj/gJWKzn0UwL4
zfk+0EzoejPdvZ5FJUfmlr8Tqk53uw+y7/0xQ6gf8lDviTrzzoeXtJUyumGBiuGx
RxFywf8n02oLYRJm5hu+0NkC+/bX0Lxg/kwiR6FLBFbBFgkWyp7FGcxhlm6ZiBfe
0KkPciWslNavn5KhljIkZDbXymbvhhSr9uBEFsyeJueA5q7sSghWloL8Ag1cac3W
e6swD1ngXtM/t5gjOLhR
=hC7z
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"We have two changes to the core framework this time around.
The first being a large change that introduces runtime PM support to
the clk framework. Now we properly call runtime PM operations on the
device providing a clk when the clk is in use. This helps on SoCs
where the clks provided by a device need something to be powered on
before using the clks, like power domains or regulators. It also helps
power those things down when clks aren't in use.
The other core change is a devm API addition for clk providers so we
can get rid of a bunch of clk driver remove functions that are just
doing of_clk_del_provider().
Outside of the core, we have the usual addition of clk drivers and
smattering of non-critical fixes to existing drivers. The biggest diff
is support for Mediatek MT2712 and MT7622 SoCs, but those patches
really just add a bunch of data.
By the way, we're trying something new here where we build the tree up
with topic branches. We plan to work this into our workflow so that we
don't step on each other's toes, and so the fixes branch can be merged
on an as-needed basis.
Summary:
Core:
- runtime PM support for clk providers
- devm API for of_clk_add_hw_provider()
New Drivers:
- Mediatek MT2712 and MT7622
- Renesas R-Car V3M SoC
Updates:
- runtime PM support for Samsung exynos5433/exynos4412 providers
- removal of clkdev aliases on Samsung SoCs
- convert clk-gpio to use gpio descriptors
- various driver cleanups to match kernel coding style
- Amlogic Video Processing Unit VPU and VAPB clks
- sigma-delta modulation for Allwinner audio PLLs
- Allwinner A83t Display clks
- support for the second display unit clock on Renesas RZ/G1E
- suspend/resume support for Renesas R-Car Gen3 CPG/MSSR
- new clock ids for Rockchip rk3188 and rk3368 SoCs
- various 'const' markings on clk_ops structures
- RPM clk support on Qualcomm MSM8996/MSM8660 SoCs"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (137 commits)
clk: stm32h7: fix test of clock config
clk: pxa: fix building on older compilers
clk: sunxi-ng: a83t: Fix i2c buses bits
clk: ti: dra7-atl-clock: fix child-node lookups
clk: qcom: common: fix legacy board-clock registration
clk: uniphier: fix DAPLL2 clock rate of Pro5
clk: uniphier: fix parent of miodmac clock data
clk: hi3798cv200: correct parent mux clock for 'clk_sdio0_ciu'
clk: hisilicon: Delete an error message for a failed memory allocation in hisi_register_clkgate_sep()
clk: hi3660: fix incorrect uart3 clock freqency
clk: kona-setup: Delete error messages for failed memory allocations
ARC: clk: fix spelling mistake: "configurarion" -> "configuration"
clk: cdce925: remove redundant check for non-null parent_name
clk: versatile: Improve sizeof() usage
clk: versatile: Delete error messages for failed memory allocations
clk: ux500: Improve sizeof() usage
clk: ux500: Delete error messages for failed memory allocations
clk: spear: Delete error messages for failed memory allocations
clk: ti: Delete error messages for failed memory allocations
clk: mmp: Adjust checks for NULL pointers
...
Make sure to search only the child nodes of "/clocks", rather than the
whole device-tree depth-first starting at "/clocks" when determining
whether to register a fixed clock in the legacy board-clock registration
helper.
Fixes: ee15faffef ("clk: qcom: common: Add API to register board clocks backwards compatibly")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add all RPM controlled clocks on msm8996 platform
[srini: Fixed various issues with offsets and made names specific to msm8996]
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The RPM clocks were missing for MSM8660/APQ8060. For this to be
completed we need to add a special fixed rate RPM clock that is used
for the PLL4 on these SoCs. The rest of the clocks are pretty
similar to the other supported platforms.
The "active" clock pattern is mirrored in all the clocks. I guess
that the PLL4 that clocks the LPASS is actually never used as
"active only" since the low-power audio subsystem should be left
on when the CPU goes to idle, so that it can be used as a stand-alone
MP3 player type of device.
The PLL4 seems to be enabled only on behalf of the booting LPASS
Hexagon - which will cast its own vote once its booted - and as
such we only configure the active state (meaning both states will
have same configuration). The result is that PLL4 will be on
from prepare() to unprepare() regardless of what the application
CPU does.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The RCGs ops for shared branches are not used now, so remove it.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that we have devm APIs for the reset controller and of clk hw
provider APIs we can remove the custom code here.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds missing LPASS smmu clks which are required by the audio driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The clock bimc_gpu_clk_src is incorrectly set to use the shared rcg2
ops, which are for RCGs with child branches controlled by different
CPUs.
The result of the incorrect ops is that the GPU's PM runtime may leave
this clock set at a very low rate. Fix this issue by using the correct
rcg2 ops.
Fixes: a2e8272f3f ("clk: qcom: Add MSM8916 gpu clocks")
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
As there is no way to actually query the hardware for the current clock
rate, now racalc_rate() just returns the last rate that was previously
set. But if the rate was not set yet, we return the bogus rate of 1000Hz.
The branch clocks have the same rate as their parent, so in this case we
just need to remove recalc_rate ops and then the core framework will handle
this automagically. The round_rate() is unused, so remove it as well.
Reported-by: Archit Taneja <architt@codeaurora.org>
Fixes: 00f64b5887 ("clk: qcom: Add support for SMD-RPM Clocks")
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
MCLK for internal audio codec is expected to be at 9.6MHz by default.
This patch adds support to 9.6MHz to make the default case possible.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds support for the global clock controller found on
the ipq8074 based devices. This includes UART, I2C, SPI etc.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
to me not catching up as quickly on patch review than anything else.
Overall it seems normal though, a few small changes to the core, mostly
small non-critical fixes here and there as well as driver updates for new
and existing hardware support. The biggest things are the TI clk driver
rework to lay the groundwork for clkctrl support in the next merge window
and the AmLogic audio/graphics clk support.
Core:
* clk_possible_parents debugfs file so we know which parents a clk
could possibly have
* Fix to make clk rate change notifiers stop on the first failure instead
of continuing
New Drivers:
* Mediatek MT6797 SoCs
* hi655x PMIC clks
* AmLogic Meson SoC i2s and spdif audio clks and Mali graphics clks
* Allwinner H5 SoCs and PRCM hardware
Updates:
* Nvidia Tegra T210 cleanups and non-critical fixes
* TI OMAP cleanups in preparation for clkctrl support
* Trivial fixes like kcalloc(), devm_* conversions, and seq_puts()
* ZTE zx296718 SoC VGA clks
* Rockchip clk-ids, fixups, and rename of rk1108 to rv1108
* Support for IDT VersaClock 5P49V5935
* Renesas R-Car H3 and M3-W IMR clks and ES2.0 rev of R-Car H3 support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=/5a/
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"Sort of on the quieter side this time, which is probably due more to
me not catching up as quickly on patch review than anything else.
Overall it seems normal though, a few small changes to the core,
mostly small non-critical fixes here and there as well as driver
updates for new and existing hardware support.
The biggest things are the TI clk driver rework to lay the groundwork
for clkctrl support in the next merge window and the AmLogic
audio/graphics clk support.
Core:
- clk_possible_parents debugfs file so we know which parents a clk
could possibly have
- Fix to make clk rate change notifiers stop on the first failure
instead of continuing
New Drivers:
- Mediatek MT6797 SoCs
- hi655x PMIC clks
- AmLogic Meson SoC i2s and spdif audio clks and Mali graphics clks
- Allwinner H5 SoCs and PRCM hardware
Updates:
- Nvidia Tegra T210 cleanups and non-critical fixes
- TI OMAP cleanups in preparation for clkctrl support
- trivial fixes like kcalloc(), devm_* conversions, and seq_puts()
- ZTE zx296718 SoC VGA clks
- Rockchip clk-ids, fixups, and rename of rk1108 to rv1108
- IDT VersaClock 5P49V5935 support
- Renesas R-Car H3 and M3-W IMR clks and ES2.0 rev of R-Car H3
support"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (151 commits)
clk: x86: pmc-atom: Checking for IS_ERR() instead of NULL
clk: ti: divider: try to fix ti_clk_register_divider
clk: mvebu: Use kcalloc() in two functions
clk: mvebu: Use kcalloc() in of_cpu_clk_setup()
clk: nomadik: Delete error messages for a failed memory allocation in two functions
clk: nomadik: Use seq_puts() in nomadik_src_clk_show()
clk: Improve a size determination in two functions
clk: Replace four seq_printf() calls by seq_putc()
clk: si5351: Delete an error message for a failed memory allocation in si5351_i2c_probe()
clk: si5351: Use devm_kcalloc() in si5351_i2c_probe()
clk: at91: Use kcalloc() in of_at91_clk_pll_get_characteristics()
reset: mediatek: Add MT2701 ethsys reset controller include file
clk: mediatek: add mt2701 ethernet reset
clk: hi6220: Add the hi655x's pmic clock
clk: ti: fix building without legacy omap3
clk: ti: fix linker error with !SOC_OMAP4
clk: hi3620: Fix a typo in one variable name
clk: hi3620: Delete error messages for a failed memory allocation in two functions
clk: hi3620: Use kcalloc() in hi3620_mmc_clk_init()
clk: hisilicon: Delete error messages for failed memory allocations in hisi_clk_init()
...
This typo is quite common. Fix it and add it to the spelling file so
that checkpatch catches it earlier.
Link: http://lkml.kernel.org/r/20170317011131.6881-2-sboyd@codeaurora.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make venus_gdsc parent of venus gdsc core0 and core1.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
rpm branch clk rate should requested as either 0 or 1 but not INT_MAX.
This patch fixes rate request for branch clocks during clk handoff.
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Fix a typo which caused both vfe0 and vfe1 powerdomains to be
named as vfe0.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Fixes: 7e824d5079 ("clk: qcom: gdsc: Add mmcc gdscs for msm8996 family")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
of_find_node_by_name() drops the reference to a passed device node.
It is not necessary to drop it again, and doing so may result in the
device node being released prematurely.
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fixes: ee15faffef ("clk: qcom: common: Add API to register board clocks backwards compatibly")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add missing clock branch to enable onboard storage
for msm899(2/4).
Signed-off-by: Jeremy McNicoll <jeremymc@redhat.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Once a gdsc is brought in and out of HW control, there is a
power down and up cycle which can take upto 1us. Polling on
the gdsc status immediately after the hw control enable/disable
can mislead software/firmware to belive the gdsc is already either on
or off, while its yet to complete the power cycle.
To avoid this add a 1us delay post a enable/disable of HW control
mode.
Also after the HW control mode is disabled, poll on the status to
check gdsc status reflects its 'on' before force disabling it
in software.
Reported-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Tested-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Fixes: 904bb4f5c7 ("clk: qcom: gdsc: Add support for gdscs with HW control")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add definition of EBI2 clock used by MDM9615 NAND controller.
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-soc@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Zoran Markovic <zmarkovic@sierrawireless.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
[sboyd@codeaurora.org: ebi2_clk halt bit is 24 not 23]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support to use reset control framework for resetting MSS
with hexagon v56 1.5.0.
Signed-off-by: Avaneesh Kumar Dwivedi <akdwived@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The current driver code gives the crash or gets hang while switching
the CPU frequency some time. The APSS CPU Clock divider is not glitch
free so it the APPS clock need to be switched for stable clock during
the change.
This patch adds the frequency change notifier for APSS CPU clock. It
changes the parent of this clock to stable PLL FEPLL500 for
PRE_RATE_CHANGE event. This event will be generated before actual
clock set operations. The clock set operation will again change its
corresponding parent by getting the same from frequency table.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
[sboyd@codeaurora.org: Indent less in probe]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This adds all RPM based clocks for msm8974, except cxo and
gfx3d_clk_src.
Tested-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The APSS CPU clock does not contain all the frequencies in its
frequency table so this patch adds the same.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
1. The parent for sdcc clock is sdccpll.
2. The frequency value was wrong so modified the same.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The current ipq4019 clock driver does not have the node for
PCNOC so this patch adds and registers the PCNOC clock nodes.
This PCNOC clock is critical and should not be turned off so
setting CRITICAL flag also.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The current ipq4019 clock driver does not have support for all
the frequency supported by APSS CPU. APSS CPU frequency is
provided with APSS CPU PLL divider which divides down the VCO
frequency. This divider is nonlinear and specific to IPQ4019
so the standard divider code cannot be used for this.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The current ipq4019 clock driver registered the PLL clocks and
dividers as fixed clock. These fixed clock needs to be removed
from driver probe function and same need to be registered with
clock framework. These PLL clocks should be programmed only
once and the same are being programmed already by the boot
loader so the set rate operation is not required for these
clocks. Only the rate can be calculated by clock operations
in clock driver file so this patch adds the same.
The PLL takes the reference clock from XO and generates the
intermediate VCO frequency. This VCO frequency will be divided
down by different PLL internal dividers. Some of the PLL
internal dividers are fixed while other are programmable.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The venus video ip's internal core blocks are under the
control of the firmware and their powerdomains needs to be
'ON' only when used by the firmware. So putting it into
hw controlled mode lets this to happen, otherwise the firmware
hangs checking for this.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some GDSCs might support a HW control mode, where in the power
domain (gdsc) is brought in and out of low power state (while
unsued) without any SW assistance, saving power.
Such GDSCs can be configured in a HW control mode when powered on
until they are explicitly requested to be powered off by software.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Fix the clk_hw references to the actual clocks and add a xlate function
to return the hw pointers from the already existing static array.
Reported-by: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Fix the clk_hw references to the actual clocks and add a xlate function
to return the hw pointers from the already existing static array.
Reported-by: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The sdcc driver for msm8996/msm8916/msm8974/msm8994 and apq8084
expects a clk_set_rate() on the sdcc rcg clk to set
a floor value of supported clk rate closest to the requested
rate, by looking up the frequency table.
So move all the sdcc rcgs on all these platforms to use the
newly introduced clk_rcg2_floor_ops
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Jeremy McNicoll <jeremymc@redhat.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The default behaviour with clk_rcg2_ops is for the
clk_round_rate()/clk_set_rate() to return/set a ceil clock
rate closest to the requested rate by looking up the corresponding
frequency table.
However, we do have some instances (mainly sdcc on various platforms)
of clients expecting a clk_set_rate() to set a floor value instead.
Add a new clk_rcg2_floor_ops to handle this for such specific
rcg instances
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This adds initial support for clocks controlled by the Resource
Power Manager (RPM) processor on some Qualcomm SoCs, which use
the qcom_rpm driver to communicate with RPM.
Such platforms are apq8064 and msm8960.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This adds initial support for clocks controlled by the Resource
Power Manager (RPM) processor on some Qualcomm SoCs, which use
the qcom_smd_rpm driver to communicate with RPM.
Such platforms are msm8916, apq8084 and msm8974.
The RPM is a dedicated hardware engine for managing the shared
SoC resources in order to keep the lowest power profile. It
communicates with other hardware subsystems via shared memory
and accepts clock requests, aggregates the requests and turns
the clocks on/off or scales them on demand.
This driver is based on the codeaurora.org driver:
https://www.codeaurora.org/cgit/quic/la/kernel/msm-3.10/tree/drivers/clk/qcom/clock-rpm.c
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
[sboyd@codeaurora.org: Remove useless braces for single line if]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Currently the RPM/RPM-SMD clock drivers do not register the xo clocks,
so we should always add factor clock. When we later add xo clocks support
into the drivers, we should update this function to skip registration.
By doing so we avoid any DT dependencies.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The clock definition was ported from the Google 3.10 kernel tree to
work with the latest kernel.
Signed-off-by: Bastian Köcher <mail@kchr.de>
[jeremymc@redhat.com: created new commit of just dt-bindings]
Signed-off-by: Jeremy McNicoll <jeremymc@redhat.com>
[sboyd@codeaurora.org: Tidy up commit text and Kconfig help]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The clocks on these boards run at 25 MHz, not 19.2 and 27 like
other platforms. Unfortunately I copy/pasted from other similar
SoCs but forgot this one is different. Fix it.
Fixes: a085f877a8 ("clk: qcom: Move cxo/pxo/xo into dt files")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add frequency tables for a few RCG clocks in msm8996
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This would be useful in subsequent patches when the .set_rate operation
would need to identify if the PLL is actually enabled
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
[sboyd@codeaurora.org: Simplify return statement of is_enabled op]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The votable alpha PLLs need to have the fsm mode enabled as part
of the initialization. The sequence seems to be the same as used
by clk-pll, so move the function which does this into a common
place and reuse it for the clk-alpha-pll
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some alpha PLLs have support for only a 16bit programable Alpha Value
(as against the default 40bits). Add a flag to handle the 16bit alpha
registers
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add a function to do initial configuration of the alpha plls
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some PLLs can support an HW FSM mode (different from the Votable FSMs,
though its the same bit used to enable Votable FSMs as well as HW FSMs)
which enables the HW to do the bypass/reset/enable-output-ctrl sequence
on its own. So all thats needed from SW is to set the FSM_ENA bit.
PLL_ACTIVE_FLAG is whats used to check if the PLL is active/enabled.
Some of the PLLs which support HW FSM can also need an OFFLINE request
that needs to be toggled across the enable/disable. We use a flag to
identify such cases and handle them.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The current I2C freq table uses MND values which is not
applicable for I2C since its RCG does not have MND
counter. This patch updates the freq table for 19.05
MHz clk frequency with FEPLL_200 parent.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Drop the assignment of regmap_read return code to val, so the code checks
the value read.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add a flag to mark gdscs which need to support the clamp deassert/assert
before and after the gdsc enable/disable
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch corrects the register offset for pcie2 pipe clock.
Offset according to datasheet is 0x6e018 instead of 0x6e108.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: b1e010c073 ("clk: qcom: Add MSM8996 Global Clock Control (GCC) driver")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch selects QCOM_GDSC Kconfig for msm8996 GCC and MMCC clock
controllers, as these provide some of the gdscs on the SOC.
Also selecting this config will make it align with other drivers which
do the same.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: 52111672f7 ("clk: qcom: gdsc: Add GDSCs in msm8996 GCC")
Fixes: 7e824d5079 ("clk: qcom: gdsc: Add mmcc gdscs for msm8996 family")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that we have clk_hw based provider APIs to register clks, we
can get rid of struct clk pointers in this driver, allowing us to
move closer to a clear split of consumer and provider clk APIs.
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add BIMC gdsc data found in MMCC part of msm8996 family of devices.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The field "owner" is set by the core.
Thus delete an unneeded initialisation.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
In order to support the Qualcomm MDM9615 SoC, add support for
the Global and LPASS Clock Controllers.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This adds the EBI2 2X and EBI2 clocks to the MSM8660/APQ8060
GCC. This is necessary to enable clocking of the external bus
interface so that peripherals on it can be mounted. These two
clocks are simple gated branch clocks.
In the vendor tree clock-8x60, these clocks have some kind of
dependency, the EBI2 clock has .depends = &ebi2_2x_clk.c,
what this means is undocumented, it doesn't seem like there
is a parent/child relationship, so the solution I chose was to
just have the EBI2 driver get and enable both clocks.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This clk is critical to operation of the SoC and should never be
turned off. Furthermore, there are no consumers of this clk so
let's just delete it so things like eMMC work.
Reported-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: b1e010c073 ("clk: qcom: Add MSM8996 Global Clock Control (GCC) driver")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The branch clocks MMSS_MMAGIC_AXI_CLK and MMAGIC_BIMC_AXI_CLK are
controlled by RPM when the APPs processor enable or disable the
RPM_MMAXI_CLK.
During the boot sequence, someone can enable the RPM_MMAXI_CLK, resulting
in register status bits showing that these clocks are enabled, our
clock driver may look at the enabled status of these clocks and try to
disable them since it thinks they are unused.
Don't make the clock driver touch these clocks.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds the CLK_SET_RATE_PARENT flag for the crypto core and
ahb blocks. Without this flag, clk_set_rate can fail for certain
frequency requests.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Fixes: 3966fab8b6 ("clk: qcom: Add MSM8916 Global Clock Controller support")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Drivers for these don't exist yet so we will add them as fixed clocks
so we don't BUG() if we change clocks that reference these clocks.
Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
When this was added not all the remaining defines were switched over to
use enums, so let's complete that process here
Reported-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The qcom_reset_ops structure is never modified. Make it const.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The offset seems to have been copied from the sata clk. Fix it so
that enabling the crypto engine source clk works.
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: 5f775498bd ("clk: qcom: Fully support apq8064 global clock control")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The clk_rcg_pixel_set_rate clk_op sets up the pre-divider by reading
its current value from the NS register.
Using the pre-divider wasn't really intended when creating these ops.
The pixel RCG was only intended to achieve fractional multiplication
provided in the pixel_table array. Leaving the pre-divider to the
existing register value results in a wrong pixel clock when the
bootloader sets up the display. This was left unidentified because
the IFC6410 Plus board on which this was verified didn't have a
bootloader that configured the display.
Don't set the RCG pre-divider in freq_tbl to the existing NS register
value. Force it to 1 and only use the M/N counter to achieve the desired
fractional multiplication.
Cc: Vinay Simha <vinaysimha@inforcecomputing.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds support for the global clock controller found on
the IPQ4019 based devices. This includes UART, I2C, SPI etc.
Signed-off-by: Pradeep Banavathi <pradeepb@codeaurora.org>
Signed-off-by: Senthilkumar N L <snlakshm@codeaurora.org>
Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
[sboyd@codeaurora.org: Drop 0x16024 enable_reg in crypto_ahb]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Georgi Djakov
Jerome Brunet
Abhishek Sahu
Stephen Boyd
Srinivas Kandagatla
Tirupathi Reddy
Linus Torvalds
Johan Hovold
Greg Kroah-Hartman
Rajendra Nayak
Linus Walleij
Stanimir Varbanov
Guenter Roeck
Jeremy McNicoll
Zoran Markovic
Avaneesh Kumar Dwivedi
Bjorn Andersson
Sricharan R
Bastian Köcher
Axel Lin
Vivek Gautam
Stephen Boyd
Markus Elfring
Neil Armstrong
Archit Taneja
Andy Gross
Matthew McClintock
Philipp Zabel
Varadarajan Narayanan