Add TCA_FQ_CODEL_CE_THRESHOLD_ECT1 boolean option to select Low Latency,
Low Loss, Scalable Throughput (L4S) style marking, along with ce_threshold.
If enabled, only packets with ECT(1) can be transformed to CE
if their sojourn time is above the ce_threshold.
Note that this new option does not change rules for codel law.
In particular, if TCA_FQ_CODEL_ECN is left enabled (this is
the default when fq_codel qdisc is created), ECT(0) packets can
still get CE if codel law (as governed by limit/target) decides so.
Section 4.3.b of current draft [1] states:
b. A scheduler with per-flow queues such as FQ-CoDel or FQ-PIE can
be used for L4S. For instance within each queue of an FQ-CoDel
system, as well as a CoDel AQM, there is typically also ECN
marking at an immediate (unsmoothed) shallow threshold to support
use in data centres (see Sec.5.2.7 of [RFC8290]). This can be
modified so that the shallow threshold is solely applied to
ECT(1) packets. Then if there is a flow of non-ECN or ECT(0)
packets in the per-flow-queue, the Classic AQM (e.g. CoDel) is
applied; while if there is a flow of ECT(1) packets in the queue,
the shallower (typically sub-millisecond) threshold is applied.
Tested:
tc qd replace dev eth1 root fq_codel ce_threshold_ect1 50usec
netperf ... -t TCP_STREAM -- K dctcp
tc -s -d qd sh dev eth1
qdisc fq_codel 8022: root refcnt 32 limit 10240p flows 1024 quantum 9212 target 5ms ce_threshold_ect1 49us interval 100ms memory_limit 32Mb ecn drop_batch 64
Sent 14388596616 bytes 9543449 pkt (dropped 0, overlimits 0 requeues 152013)
backlog 0b 0p requeues 152013
maxpacket 68130 drop_overlimit 0 new_flow_count 95678 ecn_mark 0 ce_mark 7639
new_flows_len 0 old_flows_len 0
[1] L4S current draft:
https://datatracker.ietf.org/doc/html/draft-ietf-tsvwg-l4s-arch
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Ingemar Johansson S <ingemar.s.johansson@ericsson.com>
Cc: Tom Henderson <tomh@tomh.org>
Cc: Bob Briscoe <in@bobbriscoe.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_get_dsfield(skb) gets dsfield from skb, or -1
if an error was found.
This is basically a wrapper around ipv4_get_dsfield()
and ipv6_get_dsfield().
Used by following patch for fq_codel.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Ingemar Johansson S <ingemar.s.johansson@ericsson.com>
Cc: Tom Henderson <tomh@tomh.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of percpu_counter structure to track count of orphaned
sockets is causing problems on modern hosts with 256 cpus
or more.
Stefan Bach reported a serious spinlock contention in real workloads,
that I was able to reproduce with a netfilter rule dropping
incoming FIN packets.
53.56% server [kernel.kallsyms] [k] queued_spin_lock_slowpath
|
---queued_spin_lock_slowpath
|
--53.51%--_raw_spin_lock_irqsave
|
--53.51%--__percpu_counter_sum
tcp_check_oom
|
|--39.03%--__tcp_close
| tcp_close
| inet_release
| inet6_release
| sock_close
| __fput
| ____fput
| task_work_run
| exit_to_usermode_loop
| do_syscall_64
| entry_SYSCALL_64_after_hwframe
| __GI___libc_close
|
--14.48%--tcp_out_of_resources
tcp_write_timeout
tcp_retransmit_timer
tcp_write_timer_handler
tcp_write_timer
call_timer_fn
expire_timers
__run_timers
run_timer_softirq
__softirqentry_text_start
As explained in commit cf86a086a1 ("net/dst: use a smaller percpu_counter
batch for dst entries accounting"), default batch size is too big
for the default value of tcp_max_orphans (262144).
But even if we reduce batch sizes, there would still be cases
where the estimated count of orphans is beyond the limit,
and where tcp_too_many_orphans() has to call the expensive
percpu_counter_sum_positive().
One solution is to use plain per-cpu counters, and have
a timer to periodically refresh this cache.
Updating this cache every 100ms seems about right, tcp pressure
state is not radically changing over shorter periods.
percpu_counter was nice 15 years ago while hosts had less
than 16 cpus, not anymore by current standards.
v2: Fix the build issue for CONFIG_CRYPTO_DEV_CHELSIO_TLS=m,
reported by kernel test robot <lkp@intel.com>
Remove unused socket argument from tcp_too_many_orphans()
Fixes: dd24c00191 ("net: Use a percpu_counter for orphan_count")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Stefan Bach <sfb@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mctp_key_alloc() returns a key already referenced.
The mctp_route_input() path receives a packet for a bind socket and
allocates a key. It passes the key to mctp_key_add() which takes a
refcount and adds the key to lists. mctp_route_input() should then
release its own refcount when setting the key pointer to NULL.
In the mctp_alloc_local_tag() path (for mctp_local_output()) we
similarly need to unref the key before returning (mctp_reserve_tag()
takes a refcount and adds the key to lists).
Fixes: 73c618456d ("mctp: locking, lifetime and validity changes for sk_keys")
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ansuel Smith says:
====================
Multiple improvement for qca8337 switch
This series is the final step of a long process of porting 80+ devices
to use the new qca8k driver instead of the hacky qca one based on never
merged swconfig platform.
Some background to justify all these additions.
QCA used a special binding to declare raw initval to set the swich. I
made a script to convert all these magic values and convert 80+ dts and
scan all the needed "unsupported regs". We find a baseline where we
manage to find the common and used regs so in theory hopefully we don't
have to add anymore things.
We discovered lots of things with this, especially about how differently
qca8327 works compared to qca8337.
In short, we found that qca8327 have some problem with suspend/resume for
their internal phy. It instead sets some dedicated regs that suspend the
phy without setting the standard bit. First 4 patch are to fix this.
There is also a patch about preferring master. This is directly from the
original driver and it seems to be needed to prevent some problem with
the pause frame.
Every ipq806x target sets the mac power sel and this specific reg
regulates the output voltage of the regulator. Without this some
instability can occur.
Some configuration (for some reason) swap mac6 with mac0. We add support
for this.
Also, we discovered that some device doesn't work at all with pll enabled
for sgmii line. In the original code this was based on the switch
revision. In later revision the pll regs were decided based on the switch
type (disabled for qca8327 and enabled for qca8337) but still some
device had that disabled in the initval regs.
Considering we found at least one qca8337 device that required pll
disabled to work (no traffic problem) we decided to introduce a binding
to enable pll and set it only with that.
Lastly, we add support for led open drain that require the power-on-sel
to set. Also, some device have only the power-on-sel set in the initval
so we add also support for that. This is needed for the correct function
of the switch leds.
Qca8327 have a special reg in the pws regs that set it to a reduced
48pin layout. This is needed or the switch doesn't work.
These are all the special configuration we find on all these devices that
are from various targets. Mostly ath79, ipq806x and bcm53xx.
Changes v7:
- Fix missing newline in yaml
- Handle error with wrong cpu port detected
- Move yaml commit as last to fix bot error
Changes v6:
- Convert Documentation to yaml
- Add extra check for cpu port and invalid phy mode
- Add co developed by tag to give credits to Matthew
Changes v5:
- Swap patch. Document first then implement.
- Fix some grammar error reported.
- Rework function. Remove phylink mac_config DT scan and move everything
to dedicated function in probe.
- Introduce new logic for delay selection where is also supported with
internal delay declared and rgmii set as phy mode
- Start working on ymal conversion. Will later post this in v6 when we
finally take final decision about mac swap.
Changes v4:
- Fix typo in SGMII falling edge about using PHY id instead of
switch id
Changes v3:
- Drop phy patches (proposed separateley)
- Drop special pwr binding. Rework to ipq806x specific
- Better describe compatible and add serial print on switch chip
- Drop mac exchange. Rework falling edge and move it to mac_config
- Add support for port 6 cpu port. Drop hardcoded cpu port to port0
- Improve port stability with sgmii. QCA source have intenal delay also
for sgmii
- Add warning with pll enabled on wrong configuration
Changes v2:
- Reword Documentation patch to dt-bindings
- Propose first 2 phy patch to net
- Better describe and add hint on how to use all the new
bindings
- Rework delay scan function and move to phylink mac_config
- Drop package48 wrong binding
- Introduce support for qca8328 switch
- Fix wrong binding name power-on-sel
- Return error on wrong config with led open drain and
ignore-power-on-sel not set
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the qca8k bindings to YAML format.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Co-developed-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix warning now that we have qca8k switch Documentation using yaml.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move ports related config to dedicated struct to keep things organized.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
QCA original code report port instability and sa that SGMII also require
to set internal delay. Generalize the rgmii delay function and apply the
advised value if they are not defined in DT.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
QCA8328 switch is the bigger brother of the qca8327. Same regs different
chip. Change the function to set the correct pin layout and introduce a
new match_data to differentiate the 2 switch as they have the same ID
and their internal PHY have the same ID.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
QCA8328 is the bigger brother of qca8327. Document the new compatible
binding and add some information to understand the various switch
compatible.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some qca8327 switch require to force the ignore of power on sel
strapping. Some switch require to set the led open drain mode in regs
instead of using strapping. While most of the device implements this
using the correct way using pin strapping, there are still some broken
device that require to be set using sw regs.
Introduce a new binding and support these special configuration.
As led open drain require to ignore pin strapping to work, the probe
fails with EINVAL error with incorrect configuration.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document new binding qca,ignore-power-on-sel used to ignore
power on strapping and use sw regs instead.
Document qca,led-open.drain to set led to open drain mode, the
qca,ignore-power-on-sel is mandatory with this enabled or an error will
be reported.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support enabling PLL on the SGMII CPU port. Some device require this
special configuration or no traffic is transmitted and the switch
doesn't work at all. A dedicated binding is added to the CPU node
port to apply the correct reg on mac config.
Fail to correctly configure sgmii with qca8327 switch and warn if pll is
used on qca8337 with a revision greater than 1.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document qca,sgmii-enable-pll binding used in the CPU nodes to
enable SGMII PLL on MAC config.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Future proof commit. This switch have 2 CPU ports and one valid
configuration is first CPU port set to sgmii and second CPU port set to
rgmii-id. The current implementation detects delay only for CPU port
zero set to rgmii and doesn't count any delay set in a secondary CPU
port. Drop the current delay scan function and move it to the sgmii
parser function to generalize and implicitly add support for secondary
CPU port set to rgmii-id. Introduce new logic where delay is enabled
also with internal delay binding declared and rgmii set as PHY mode.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently CPU port is always hardcoded to port 0. This switch have 2 CPU
ports. The original intention of this driver seems to be use the
mac06_exchange bit to swap MAC0 with MAC6 in the strange configuration
where device have connected only the CPU port 6. To skip the
introduction of a new binding, rework the driver to address the
secondary CPU port as primary and drop any reference of hardcoded port.
With configuration of mac06 exchange, just skip the definition of port0
and define the CPU port as a secondary. The driver will autoconfigure
the switch to use that as the primary CPU port.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch now support CPU port to be set 6 instead of be hardcoded to
0. Document support for it and describe logic selection.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for this in the qca8k driver. Also add support for SGMII
rx/tx clock falling edge. This is only present for pad0, pad5 and
pad6 have these bit reserved from Documentation. Add a comment that this
is hardcoded to PAD0 as qca8327/28/34/37 have an unique sgmii line and
setting falling in port0 applies to both configuration with sgmii used
for port0 or port6.
Co-developed-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add names and descriptions of additional PORT0_PAD_CTRL properties.
qca,sgmii-(rx|tx)clk-falling-edge are for setting the respective clock
phase to failling edge.
Co-developed-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing mac power sel support needed for ipq8064/5 SoC that require
1.8v for the internal regulator port instead of the default 1.5v.
If other device needs this, consider adding a dedicated binding to
support this.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable err is being initialized with a value that is never read, it
is being updated immediately afterwards. The assignment is redundant and
can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the 32-bit arch with 64-bit DMA seems to rare those days,
and page pool might carry a lot of code and complexity for
systems that possibly.
So disable dma mapping support for such systems, if drivers
really want to work on such systems, they have to implement
their own DMA-mapping fallback tracking outside page_pool.
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Srujana Challa says:
====================
octeontx2-af: Miscellaneous changes for CPT
This patchset consists of miscellaneous changes for CPT.
First patch enables the CPT HW interrupts, second patch
adds support for CPT LF teardown in non FLR path and
final patch does CPT CTX flush in FLR handler.
v2:
- Fixed a warning reported by kernel test robot.
====================
Link: https://lore.kernel.org/r/20211013055621.1812301-1-schalla@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Adds support to flush or invalidate CPT CTX entries as part of FLR
and also provides a mailbox to flush CPT CTX entries in case of
graceful exit.
This patch also adds support for AF -> CPT PF uplink mailbox messages
and adds a new mbox message to submit a CPT instruction from AF.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Perform CPT LF teardown in non FLR path as well via cpt_lf_free()
Currently CPT LF teardown and reset sequence is only
done when FLR is handled with CPT LF still attached.
This patch also fixes cpt_lf_alloc() to set EXEC_LDWB in
CPT_AF_LFX_CTL2 when being completely overwritten as that is
the default value and is better for performance.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch enables and registers interrupt handler for CPT HW
interrupts.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On i386, when builtin (not a loadable module), the winbond-840 driver
inspects boot_cpu_data to see what CPU family it is running on, and
then acts on that data. The "family" struct member (x86) does not exist
when running on UML, so prevent that test and do the default action.
Prevents this build error on UML + i386:
../drivers/net/ethernet/dec/tulip/winbond-840.c: In function ‘init_registers’:
../drivers/net/ethernet/dec/tulip/winbond-840.c:882:19: error: ‘struct cpuinfo_um’ has no member named ‘x86’
if (boot_cpu_data.x86 <= 4) {
Fixes: 68f5d3f3b6 ("um: add PCI over virtio emulation driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: linux-um@lists.infradead.org
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Link: https://lore.kernel.org/r/20211014050606.7288-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On a UML build, the igc_ptp driver uses CONFIG_X86_TSC for timestamp
conversion. The function that is used is not available on UML builds,
so have the function use the default system_counterval_t timestamp
instead for UML builds.
Prevents this build error on UML:
../drivers/net/ethernet/intel/igc/igc_ptp.c: In function ‘igc_device_tstamp_to_system’:
../drivers/net/ethernet/intel/igc/igc_ptp.c:777:9: error: implicit declaration of function ‘convert_art_ns_to_tsc’ [-Werror=implicit-function-declaration]
return convert_art_ns_to_tsc(tstamp);
../drivers/net/ethernet/intel/igc/igc_ptp.c:777:9: error: incompatible types when returning type ‘int’ but ‘struct system_counterval_t’ was expected
return convert_art_ns_to_tsc(tstamp);
Fixes: 68f5d3f3b6 ("um: add PCI over virtio emulation driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: linux-um@lists.infradead.org
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Link: https://lore.kernel.org/r/20211014050516.6846-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On i386, when builtin (not a loadable module), the fealnx driver
inspects boot_cpu_data to see what CPU family it is running on, and
then acts on that data. The "family" struct member (x86) does not exist
when running on UML, so prevent that test and do the default action.
Prevents this build error on UML + i386:
../drivers/net/ethernet/fealnx.c: In function ‘netdev_open’:
../drivers/net/ethernet/fealnx.c:861:19: error: ‘struct cpuinfo_um’ has no member named ‘x86’
Fixes: 68f5d3f3b6 ("um: add PCI over virtio emulation driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: linux-um@lists.infradead.org
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Link: https://lore.kernel.org/r/20211014050500.5620-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Adding comment to avoid the misusing of netvsc_xdp_xmit().
Otherwise the value of skb->queue_mapping could be 0 and
then the return value of skb_get_rx_queue() could be MAX_U16
cause by overflow.
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Link: https://lore.kernel.org/r/1634174786-1810351-1-git-send-email-jiasheng@iscas.ac.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Borkmann says:
====================
Minor managed neighbor follow-ups
Minor follow-up series to address prior feedback from David and Jakub.
Patch 1 adds a build time assertion to prevent overflows when shifting
in extended flags, patch 2 is a cleanup to use NLA_POLICY_MASK instead
of open-coding invalid flags rejection and patch 3 rejects creating new
neighbors with NUD_PERMANENT & NTF_MANAGED. For details, see individual
patches.
====================
Link: https://lore.kernel.org/r/20211013132140.11143-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The combination of NUD_PERMANENT + NTF_MANAGED is not supported and does
not make sense either given the former indicates a static/fixed neighbor
entry whereas the latter a dynamically resolved one. While it is possible
to transition from one over to the other, we should however reject such
creation attempts.
Fixes: 7482e3841d ("net, neigh: Add NTF_MANAGED flag for managed neighbor entries")
Suggested-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Instead of open-coding a check for invalid bits in NTF_EXT_MASK, we can just
use the NLA_POLICY_MASK() helper instead, and simplify NDA_FLAGS_EXT sanity
check this way.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, NDA_FLAGS_EXT flags allow a maximum of 24 bits to be used for
extended neighbor flags. These are eventually fed into neigh->flags by
shifting with NTF_EXT_SHIFT as per commit 2c611ad97a ("net, neigh:
Extend neigh->flags to 32 bit to allow for extensions").
If really ever needed in future, the full 32 bits from NDA_FLAGS_EXT can
be used, it would only require to move neigh->flags from u32 to u64 inside
the kernel.
Add a build-time assertion such that when extending the NTF_EXT_MASK with
new bits, we'll trigger an error once we surpass the 24th bit. This assumes
that no bit holes in new NTF_EXT_* flags will slip in from UAPI, but I
think this is reasonable to assume.
Suggested-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
PHY driver dp83867 has rich supports for OF-platform to fine-tune the PHY
chip during phy configuration. However, for non-OF platform, certain PHY
tunable parameters such as IO impedance and RX & TX internal delays are
critical and should be initialized to its default during PHY driver probe.
Tested-by: Clement <clement@intel.com>
Signed-off-by: Lay, Kuan Loon <kuan.loon.lay@intel.com>
Co-developed-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://lore.kernel.org/r/20211013065941.2124858-1-boon.leong.ong@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the PTP_PEROUT_DUTY_CYCLE flag is set, then check if the
request_on value in ptp_perout_request matches the pre-defined
values or a toggle option.
Return a failure if the value is not supported.
Preserve the old behaviors if the PTP_PEROUT_DUTY_CYCLE flag is not
set.
Tested with an oscilloscope on EVB-LAN7430:
e.g., to output PPS 1sec period 500mS on (high) to GPIO 2.
./testptp -L 2,2
./testptp -p 1000000000 -w 500000000
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Link: https://lore.kernel.org/r/1634046593-64312-1-git-send-email-yuiko.oshino@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It seems reasonable to fine-tune only some of the skew values when using
one of the rgmii-*id PHY modes, and even when all skew values are
specified, using the correct ID PHY mode makes sense for documentation
purposes. Such a configuration also appears in the binding docs in
Documentation/devicetree/bindings/net/micrel-ksz90x1.txt, so the driver
should not warn about it.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20211012103402.21438-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
tools/testing/selftests/net/ioam6.sh
7b1700e009 ("selftests: net: modify IOAM tests for undef bits")
bf77b1400a ("selftests: net: Test for the IOAM encapsulation with IPv6")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Moving the of_net code from drivers/of/ to net/core means we
no longer stub out the helpers when networking is disabled,
which leads to a randconfig build failure with at least one
ARM platform that calls this from non-networking code:
arm-linux-gnueabi-ld: arch/arm/mach-mvebu/kirkwood.o: in function `kirkwood_dt_eth_fixup':
kirkwood.c:(.init.text+0x54): undefined reference to `of_get_mac_address'
Restore the way this worked before by changing that #ifdef
check back to testing for both CONFIG_OF and CONFIG_NET.
Fixes: e330fb1459 ("of: net: move of_net under net/")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211014090055.2058949-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Current release - regressions:
- af_unix: rename UNIX-DGRAM to UNIX to maintain backwards compatibility
- procfs: revert "add seq_puts() statement for dev_mcast",
minor format change broke user space
Current release - new code bugs:
- dsa: fix bridge_num not getting cleared after ports leaving
the bridge, resource leak
- dsa: tag_dsa: send packets with TX fwd offload from VLAN-unaware
bridges using VID 0, prevent packet drops if pvid is removed
- dsa: mv88e6xxx: keep the pvid at 0 when VLAN-unaware, prevent
HW getting confused about station to VLAN mapping
Previous releases - regressions:
- virtio-net: fix for skb_over_panic inside big mode
- phy: do not shutdown PHYs in READY state
- dsa: mv88e6xxx: don't use PHY_DETECT on internal PHY's,
fix link LED staying lit after ifdown
- mptcp: fix possible infinite wait on recvmsg(MSG_WAITALL)
- mqprio: Correct stats in mqprio_dump_class_stats()
- ice: fix deadlock for Tx timestamp tracking flush
- stmmac: fix feature detection on old hardware
Previous releases - always broken:
- sctp: account stream padding length for reconf chunk
- icmp: fix icmp_ext_echo_iio parsing in icmp_build_probe()
- isdn: cpai: check ctr->cnr to avoid array index out of bound
- isdn: mISDN: fix sleeping function called from invalid context
- nfc: nci: fix potential UAF of rf_conn_info object
- dsa: microchip: prevent ksz_mib_read_work from kicking back
in after it's canceled in .remove and crashing
- dsa: mv88e6xxx: isolate the ATU databases of standalone and
bridged ports
- dsa: sja1105, ocelot: break circular dependency between switch
and tag drivers
- dsa: felix: improve timestamping in presence of packe loss
- mlxsw: thermal: fix out-of-bounds memory accesses
Misc:
- ipv6: ioam: move the check for undefined bits to improve
interoperability
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=/K9E
-----END PGP SIGNATURE-----
Merge tag 'net-5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Quite calm.
The noisy DSA driver (embedded switches) changes, and adjustment to
IPv6 IOAM behavior add to diffstat's bottom line but are not scary.
Current release - regressions:
- af_unix: rename UNIX-DGRAM to UNIX to maintain backwards
compatibility
- procfs: revert "add seq_puts() statement for dev_mcast", minor
format change broke user space
Current release - new code bugs:
- dsa: fix bridge_num not getting cleared after ports leaving the
bridge, resource leak
- dsa: tag_dsa: send packets with TX fwd offload from VLAN-unaware
bridges using VID 0, prevent packet drops if pvid is removed
- dsa: mv88e6xxx: keep the pvid at 0 when VLAN-unaware, prevent HW
getting confused about station to VLAN mapping
Previous releases - regressions:
- virtio-net: fix for skb_over_panic inside big mode
- phy: do not shutdown PHYs in READY state
- dsa: mv88e6xxx: don't use PHY_DETECT on internal PHY's, fix link
LED staying lit after ifdown
- mptcp: fix possible infinite wait on recvmsg(MSG_WAITALL)
- mqprio: Correct stats in mqprio_dump_class_stats()
- ice: fix deadlock for Tx timestamp tracking flush
- stmmac: fix feature detection on old hardware
Previous releases - always broken:
- sctp: account stream padding length for reconf chunk
- icmp: fix icmp_ext_echo_iio parsing in icmp_build_probe()
- isdn: cpai: check ctr->cnr to avoid array index out of bound
- isdn: mISDN: fix sleeping function called from invalid context
- nfc: nci: fix potential UAF of rf_conn_info object
- dsa: microchip: prevent ksz_mib_read_work from kicking back in
after it's canceled in .remove and crashing
- dsa: mv88e6xxx: isolate the ATU databases of standalone and bridged
ports
- dsa: sja1105, ocelot: break circular dependency between switch and
tag drivers
- dsa: felix: improve timestamping in presence of packe loss
- mlxsw: thermal: fix out-of-bounds memory accesses
Misc:
- ipv6: ioam: move the check for undefined bits to improve
interoperability"
* tag 'net-5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (60 commits)
icmp: fix icmp_ext_echo_iio parsing in icmp_build_probe
MAINTAINERS: Update the devicetree documentation path of imx fec driver
sctp: account stream padding length for reconf chunk
mlxsw: thermal: Fix out-of-bounds memory accesses
ethernet: s2io: fix setting mac address during resume
NFC: digital: fix possible memory leak in digital_in_send_sdd_req()
NFC: digital: fix possible memory leak in digital_tg_listen_mdaa()
nfc: fix error handling of nfc_proto_register()
Revert "net: procfs: add seq_puts() statement for dev_mcast"
net: encx24j600: check error in devm_regmap_init_encx24j600
net: korina: select CRC32
net: arc: select CRC32
net: dsa: felix: break at first CPU port during init and teardown
net: dsa: tag_ocelot_8021q: fix inability to inject STP BPDUs into BLOCKING ports
net: dsa: felix: purge skb from TX timestamping queue if it cannot be sent
net: dsa: tag_ocelot_8021q: break circular dependency with ocelot switch lib
net: dsa: tag_ocelot: break circular dependency with ocelot switch lib driver
net: mscc: ocelot: cross-check the sequence id from the timestamp FIFO with the skb PTP header
net: mscc: ocelot: deny TX timestamping of non-PTP packets
net: mscc: ocelot: warn when a PTP IRQ is raised for an unknown skb
...
random_ether_addr() was the original name of the helper which
was kept for backward compatibility (?) after the rename in
commit 0a4dd59498 ("etherdevice: Rename random_ether_addr
to eth_random_addr").
We have a single random_ether_addr() caller left in tree
while there are 70 callers of eth_random_addr().
Time to drop this define.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20211013205450.328092-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski says:
====================
ethernet: more netdev->dev_addr write removals
Another series removing direct writes to netdev->dev_addr.
====================
Link: https://lore.kernel.org/r/20211013204435.322561-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
This patch takes care of drivers which cast netdev->dev_addr to
a 16bit type, often with an explicit byte order.
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A handful of drivers contains loops assigning the mac
addr byte by byte. Convert those to eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A straggler I somehow missed in the automated conversion in
commit 9ca01b25df ("ethernet: use of_get_ethdev_address()").
Use the new helper instead of using netdev->dev_addr directly.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A handful of drivers use sizeof(addr) for the size of
the address, after manually confirming the size is
indeed 6 convert them to eth_hw_addr_set().
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Petko Manolov <petkan@nucleusys.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Number of drivers use eth_random_addr(netdev->dev_addr)
thus writing to netdev->dev_addr directly, and not setting
the address type. Switch them to eth_hw_addr_random().
@@
expression netdev;
@@
- eth_random_addr(netdev->dev_addr);
+ eth_hw_addr_random(netdev);
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet
Matt Johnston
David S. Miller
Matthew Hagan
Ansuel Smith
Colin Ian King
Yunsheng Lin
Jakub Kicinski
Srujana Challa
Nithin Dabilpuram
Randy Dunlap
Jiasheng Jiang
Daniel Borkmann
Yuval Shaia
Lay, Kuan Loon
Yuiko Oshino
Matthias Schiffer
Arnd Bergmann
Linus Torvalds