arch/arm/boot/bootp/bootp.lds:22: ERROR: trailing whitespace
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove duplicated #include('s) in
arch/arm/mach-spear6xx/spear6xx.c
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch only moves the initial entry code which setups the mapping
from what ever to KERNELBASE into a seperate file. No code change has
been made here.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
During boot we change the mapping a few times until we have a "defined"
mapping. During this procedure a small 4KiB mapping is created and after
that one a 64MiB. Currently the offset of the 4KiB page in that we run
is zero because the complete startup up code is in first page which
starts at RPN zero.
If the code is recycled and moved to another location then its execution
will fail because the start address in 64 MiB mapping is computed
wrongly. It does not consider the offset to the page from the begin of
the memory.
This patch fixes this. Usually (system boot) r25 is zero so this does
not change anything unless the code is recycled.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin: (30 commits)
Blackfin: SMP: fix continuation lines
Blackfin: acvilon: fix timeout usage for I2C
Blackfin: fix typo in BF537 IRQ comment
Blackfin: unify duplicate MEM_MT48LC32M8A2_75 kconfig options
Blackfin: set ARCH_KMALLOC_MINALIGN
Blackfin: use atomic kmalloc in L1 alloc so it too can be atomic
Blackfin: another year of changes (update copyright in boot log)
Blackfin: optimize strncpy a bit
Blackfin: isram: clean up ITEST_COMMAND macro and improve the selftests
Blackfin: move string functions to normal lib/ assembly
Blackfin: SIC: cut down on IAR MMR reads a bit
Blackfin: bf537-minotaur: fix build errors due to header changes
Blackfin: kgdb: pass up the CC register instead of a 0 stub
Blackfin: handle HW errors in the new "FAULT" printing code
Blackfin: show the whole accumulator in the pseudo DBG insn
Blackfin: support all possible registers in the pseudo instructions
Blackfin: add support for the DBG (debug output) pseudo insn
Blackfin: change the BUG opcode to an unused 16-bit opcode
Blackfin: allow NMI watchdog to be used w/RETN as a scratch reg
Blackfin: add support for the DBGA (debug assert) pseudo insn
...
* 'bkl/ioctl' of git://git.kernel.org/pub/scm/linux/kernel/git/frederic/random-tracing:
uml: Pushdown the bkl from harddog_kern ioctl
sunrpc: Pushdown the bkl from sunrpc cache ioctl
sunrpc: Pushdown the bkl from ioctl
autofs4: Pushdown the bkl from ioctl
uml: Convert to unlocked_ioctls to remove implicit BKL
ncpfs: BKL ioctl pushdown
coda: Clean-up whitespace problems in pioctl.c
coda: BKL ioctl pushdown
drivers: Push down BKL into various drivers
isdn: Push down BKL into ioctl functions
scsi: Push down BKL into ioctl functions
dvb: Push down BKL into ioctl functions
smbfs: Push down BKL into ioctl function
coda/psdev: Remove BKL from ioctl function
um/mmapper: Remove BKL usage
sn_hwperf: Kill BKL usage
hfsplus: Push down BKL into ioctl function
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (25 commits)
sh: fix up sh7785lcr_32bit_defconfig.
arch/sh/lib/strlen.S: Checkpatch cleanup
sh: fix up sh7786 dmaengine build.
sh: guard cookie consistency across termination in the DMA driver
sh: prevent the DMA driver from unloading, while in use
sh: fix Oops in the serial SCI driver
sh: allow platforms to specify SD-card supported voltages
mmc: let MFD's provide supported Vdd card voltages to tmio_mmc
sh: disable SD-card write-protection detection on kfr2r09
mfd: pass platform flags down to the tmio_mmc driver
tmio: add a platform flag to disable card write-protection detection
sh: Add SDHI DMA support to migor
sh: Add SDHI DMA support to kfr2r09
sh: Add SDHI DMA support to ms7724se
sh: Add SDHI DMA support to ecovec
mmc: add DMA support to tmio_mmc driver, when used on SuperH
sh: prepare the SDHI MFD driver to pass DMA configuration to tmio_mmc.c
mmc: prepare tmio_mmc for passing of DMA configuration from the MFD cell
sh: add DMA slave definitions to sh7724
sh: add DMA slaves for two SDHI controllers to sh7722
...
arch/m68knommu/mm/fault.c:39: WARNING: space prohibited between function name and open parenthesis '('
arch/m68knommu/mm/fault.c:47: WARNING: braces {} are not necessary for any arm of this statement
arch/m68knommu/mm/fault.c:51: ERROR: space required after that ',' (ctx:VxV)
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
While it is explained in the long help text, meaning of '0' for RAMSIZE
is easily overlooked because is not mentioned in the short help text.
Add that.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Remove the un-used mcfsmc.h. All ColdFire platforms that use SMC ethernet
devices are platform enabled to use the smc91x driver.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The ColdFire based NETtel boards use the SMC9196 ethernet devices.
Switch to using a platform setup for these parts using the smc91x driver.
The init code is taken strait out of arch/m68k/include/asm/mcfsmc.h,
just cleaned up a bit.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The Freescale M5249EVB board is fitted with an SMC LAN91c11 ethernet
device. Add platform support to the M5249EVB setup code to support this.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The TASK_SIZE define is used in some places as a limit on the size of
the virtual address space of a process. On non-MMU systems those addresses
used in comparison will be physical addresses, and they could be anywhere
in the 32bit physical address space. So for !CONFIG_MMU systems set the
TASK_SIZE to the maximum physical address.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The build scripts inadvertently dropped this down to 29-bit, fix it
back up.
Reported-by: Raul Porcel <armin76@gentoo.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fixup the defconfig post the latest moves, so ARCH_S5PC1XX becomes
ARCH_S5PC100 which is sufficient to get the system building.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Between problems with Kconfig and merging commits from several
different sources, it seems the s5pc100 build's move from plat-s5pc11
has had a few problems.
Since I do not have the trees to rebuild this quickly, the easiest
thing is to simply fix the errors found once the s5pc100_defconfig
actually builds.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Samsung's Soc S5PC100 has three PL330 DMACs. First is dedicated for
Memory->Memory data transfer while the other two meant for data
transfer with peripherals.
Define and add latter two PL330 DMACs as platform devices on the
S5PC100 platform.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Somewhere during the latest platform cleanups the IRQ_EINT definition
got broken, so fix it by replacing it in <mach/irqs.h>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
When saving GPIOs during suspend/resume we need skip missing GPIO banks, not
trying get corresponding chip again and again in infinite loop.
Signed-off-by: Jiri Pinkava <jiri.pinkava@vscht.cz>
[ben-linux@fluff.org: shorten subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Get rid of the duplicated entries in prefix_codes[]
to eliminate redundant checks by skip_prefix().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Pekka Paalanen <pq@iki.fi>
LKML-Reference: <1274140110-5841-1-git-send-email-akinobu.mita@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The timeout value is in jiffies, so it should be using HZ, not a plain
number. As '10000' is ambiguous, 1HZ is used as conservative default.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Valentin Yakovenkov <yakovenkov@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Architectures that handle DMA-non-coherent memory need to set
ARCH_KMALLOC_MINALIGN to make sure that kmalloc'ed buffer is DMA-safe:
the buffer doesn't share a cache with the others.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Some drivers allocate L1 SRAM in atomic contexts, so make sure these
functions also use GFP_ATOMIC to avoid BUG()'s.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Add a little strncpy optimization which can easily cut boot time by 20%.
When the kernel is booting with initramfs, it builds up the filesystem
from a cpio archive by calling strncpy_from_user() via fs/namei.c's
do_getname() on every file in the archive (which can be lots) with a
length of PATH_MAX (1024). This causes the dest of the strncpy to be
padded with many NUL bytes.
This optimization mostly causes these NUL bytes to be padded with a call
to memset() which is already optimized for filling memory quickly, but
the hardware loop helps a little bit as well.
Boot time measured with 'loglevel=0' so UART speed doesn't get in the way.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The IADDR2DTEST() macro had some duplicated logic with bit 11 and some
incorrect comments, so scrub all of that.
In order to verify these aren't a problem (and won't be in the future),
extend the self tests to operate on as much L1 SRAM as possible.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Since 'extern inline' doesn't work correctly in the context of the Linux
kernel (too many overriding defines), move the string functions to normal
lib/ assembly files (like the existing mem funcs). This avoids the forced
inline all over the kernel and allows us to place them constantly in L1.
This also avoids some module failures when gcc inserts calls to string
functions but the kernel build system doesn't fully consult the library
archives.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Tweak the for loops that operate on the SIC IAR system MMRs to avoid
re-reading them multiple times in a row. System MMRs are a little
slower to access, so avoid the penalty when possible.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
While the CC pseudo register can be deduced from the ASTAT register, make
sure we set its value correctly instead of always stubbing it out as 0.
GDB itself looks at this pseudo register instead of ASTAT, so we have to
supply the right value.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Rather than print just part of the accumulator register, show the whole
40 bits. This matches the simulator behavior better.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Rather than decoding just the common R/P registers, handle all of them.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Another pseudo insn used by Blackfin simulators. Also factor some now
common register lookup code out of the DBGA handlers.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The current BUG opcode includes the bit that flags the insn as a 32bit
opcode, but it wasn't declaring it as 32bits. So pick an unused 16bit.
URL: http://blackfin.uclinux.org/gf/tracker/5973
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
NMIs are not safe to return from because many anomaly workarounds are
implemented by disabling interrupts. The NMI obviously violates this
assumption. Since the NMI watchdog never returns, we don't have to
worry about it clobbering RETN when it is being used as a scratch register
with the exception stack.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
A few pseudo debug insns exist to make testing of simulators easier.
Since these don't actually exist in the hardware, we have to have the
exception handler take care of emulating these. This allows sim test
cases to be executed unmodified under Linux and thus simplify debugging
greatly.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Pushdown the bkl to harddog_ioctl.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Uml <user-mode-linux-devel@lists.sourceforge.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: John Kacur <jkacur@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
kfr2r09 board has a micro-SD card slot, therefore card write-protection
detection cannot work there, disable it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a list of SCIF and SDHI DMA slave definitions to sh7724.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SuperH SDHI controllers can use DMA, add slave definitions to sh7722.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that DMA slave IDs are only used used in platform specific code and have
become opaque cookies for the rest of the code, we can make the, CPU specific
too.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Ecovec uses the AK8813 video envoder similarly to the ms7724se platform with
the only difference, that on ecovec GPIOs are used for resetting and powering
up and down the chip.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Merging in current state of Linus' tree to deal with merge conflicts and
build failures in vio.c after merge.
Conflicts:
drivers/i2c/busses/i2c-cpm.c
drivers/i2c/busses/i2c-mpc.c
drivers/net/gianfar.c
Also fixed up one line in arch/powerpc/kernel/vio.c to use the
correct node pointer.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
.name, .match_table and .owner are duplicated in both of_platform_driver
and device_driver. This patch is a removes the extra copies from struct
of_platform_driver and converts all users to the device_driver members.
This patch is a pretty mechanical change. The usage model doesn't change
and if any drivers have been missed, or if anything has been fixed up
incorrectly, then it will fail with a compile time error, and the fixup
will be trivial. This patch looks big and scary because it touches so
many files, but it should be pretty safe.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
OF-style matching can be available to any device, on any type of bus.
This patch allows any driver to provide an OF match table when CONFIG_OF
is enabled so that drivers can be bound against devices described in
the device tree.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
By moving dma_mask into pdev_archdata, and adding archdata to
struct of_device, it makes it possible to substitute of_device
with struct platform_device, which is a stepping stone to
removing the of_platform bus entirely.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
By moving dma_mask into pdev_archdata, and adding archdata to
struct of_device, it makes it possible to substitute of_device
with struct platform_device, which is a stepping stone to
removing the of_platform bus entirely.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (69 commits)
fix handling of offsets in cris eeprom.c, get rid of fake on-stack files
get rid of home-grown mutex in cris eeprom.c
switch ecryptfs_write() to struct inode *, kill on-stack fake files
switch ecryptfs_get_locked_page() to struct inode *
simplify access to ecryptfs inodes in ->readpage() and friends
AFS: Don't put struct file on the stack
Ban ecryptfs over ecryptfs
logfs: replace inode uid,gid,mode initialization with helper function
ufs: replace inode uid,gid,mode initialization with helper function
udf: replace inode uid,gid,mode init with helper
ubifs: replace inode uid,gid,mode initialization with helper function
sysv: replace inode uid,gid,mode initialization with helper function
reiserfs: replace inode uid,gid,mode initialization with helper function
ramfs: replace inode uid,gid,mode initialization with helper function
omfs: replace inode uid,gid,mode initialization with helper function
bfs: replace inode uid,gid,mode initialization with helper function
ocfs2: replace inode uid,gid,mode initialization with helper function
nilfs2: replace inode uid,gid,mode initialization with helper function
minix: replace inode uid,gid,mode init with helper
ext4: replace inode uid,gid,mode init with helper
...
Trivial conflict in fs/fs-writeback.c (mark bitfields unsigned)
* git://git.infradead.org/iommu-2.6:
intel-iommu: Set a more specific taint flag for invalid BIOS DMAR tables
intel-iommu: Combine the BIOS DMAR table warning messages
panic: Add taint flag TAINT_FIRMWARE_WORKAROUND ('I')
panic: Allow warnings to set different taint flags
intel-iommu: intel_iommu_map_range failed at very end of address space
intel-iommu: errors with smaller iommu widths
intel-iommu: Fix boot inside 64bit virtualbox with io-apic disabled
intel-iommu: use physfn to search drhd for VF
intel-iommu: Print out iommu seq_id
intel-iommu: Don't complain that ACPI_DMAR_SCOPE_TYPE_IOAPIC is not supported
intel-iommu: Avoid global flushes with caching mode.
intel-iommu: Use correct domain ID when caching mode is enabled
intel-iommu mistakenly uses offset_pfn when caching mode is enabled
intel-iommu: use for_each_set_bit()
intel-iommu: Fix section mismatch dmar_ir_support() uses dmar_tbl.
* 'kvm-updates/2.6.35' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (269 commits)
KVM: x86: Add missing locking to arch specific vcpu ioctls
KVM: PPC: Add missing vcpu_load()/vcpu_put() in vcpu ioctls
KVM: MMU: Segregate shadow pages with different cr0.wp
KVM: x86: Check LMA bit before set_efer
KVM: Don't allow lmsw to clear cr0.pe
KVM: Add cpuid.txt file
KVM: x86: Tell the guest we'll warn it about tsc stability
x86, paravirt: don't compute pvclock adjustments if we trust the tsc
x86: KVM guest: Try using new kvm clock msrs
KVM: x86: export paravirtual cpuid flags in KVM_GET_SUPPORTED_CPUID
KVM: x86: add new KVMCLOCK cpuid feature
KVM: x86: change msr numbers for kvmclock
x86, paravirt: Add a global synchronization point for pvclock
x86, paravirt: Enable pvclock flags in vcpu_time_info structure
KVM: x86: Inject #GP with the right rip on efer writes
KVM: SVM: Don't allow nested guest to VMMCALL into host
KVM: x86: Fix exception reinjection forced to true
KVM: Fix wallclock version writing race
KVM: MMU: Don't read pdptrs with mmu spinlock held in mmu_alloc_roots
KVM: VMX: enable VMXON check with SMX enabled (Intel TXT)
...
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86: (32 commits)
Move N014, N051 and CR620 dmi information to load scm dmi table
drivers/platform/x86/eeepc-wmi.c: fix build warning
X86 platfrom wmi: Add debug facility to dump WMI data in a readable way
X86 platform wmi: Also log GUID string when an event happens and debug is set
X86 platform wmi: Introduce debug param to log all WMI events
Clean up all objects used by scm model when driver initial fail or exit
msi-laptop: fix up some coding style issues found by checkpatch
msi-laptop: Add i8042 filter to sync sw state with BIOS when function key pressed
msi-laptop: Set rfkill init state when msi-laptop intiial
msi-laptop: Add MSI CR620 notebook dmi information to scm models table
msi-laptop: Add N014 N051 dmi information to scm models table
drivers/platform/x86: Use kmemdup
drivers/platform/x86: Use kzalloc
drivers/platform/x86: Clarify the MRST IPC driver description slightly
eeepc-wmi: depends on BACKLIGHT_CLASS_DEVICE
IPC driver for Intel Mobile Internet Device (MID) platforms
classmate-laptop: Add RFKILL support.
thinkpad-acpi: document backlight level writeback at driver init
thinkpad-acpi: clean up ACPI handles handling
thinkpad-acpi: don't depend on led_path for led firmware type (v2)
...
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
DMAENGINE: extend the control command to include an arg
async_tx: trim dma_async_tx_descriptor in 'no channel switch' case
DMAENGINE: DMA40 fix for allocation of logical channel 0
DMAENGINE: DMA40 support paused channel status
dmaengine: mpc512x: Use resource_size
DMA ENGINE: Do not reset 'private' of channel
ioat: Remove duplicated devm_kzalloc() calls for ioatdma_device
ioat3: disable cacheline-unaligned transfers for raid operations
ioat2,3: convert to producer/consumer locking
ioat: convert to circ_buf
DMAENGINE: Support for ST-Ericssons DMA40 block v3
async_tx: use of kzalloc/kfree requires the include of slab.h
dmaengine: provide helper for setting txstate
DMAENGINE: generic channel status v2
DMAENGINE: generic slave control v2
dma: timb-dma: Update comment and fix compiler warning
dma: Add timb-dma
DMAENGINE: COH 901 318 fix bytesleft
DMAENGINE: COH 901 318 rename confusing vars
Read the memory ranges behind the Broadcom CNB20LE host bridge out of the
hardware. This allows PCI hotplugging to work, since we know which memory
range to allocate PCI BAR's from.
The x86 PCI code automatically prefers the ACPI _CRS information when it is
available. In that case, this information is not used.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'msm-mmc_sdcc' of git://codeaurora.org/quic/kernel/dwalker/linux-msm:
drivers: mmc: msm_sdcc: Add EMBEDDED_SDIO support
mmc: msm_sdcc: Fix issue where clocks could be disabled mid transaction
mmc: msm_sdcc: Fix the dma exec function to use the proper delays
mmc: msm_sdcc: Don't set host->curr.mrq until after we're sure the busclk timer won't fire
mmc: msm_sdcc: Enable busclk idle timer for power savings
mmc: msm_sdcc: Don't disable interrupts while suspending
mmc: msm_sdcc: Fix issue where we might not end a sucessfull request
mmc: msm_sdcc: Featurize busclock power save and disable it by default
mmc: msm_sdcc: Fix bug where busclk expiry timer was not properly disabled
mmc: msm_sdcc: Reduce command timeouts and improve reliability.
mmc: msm_sdcc: Schedule clock disable after probe
mmc: msm_sdcc: Wrap readl/writel calls with appropriate clk delays
mmc: msm_sdcc: Driver clocking/irq improvements
msm: Add 'execute' datamover callback
mmc: msm_sdcc: Snoop SDIO_CCCR_ABORT register
mmc: msm_sdcc: Clean up clock management and add a 10us delay after enabling clocks
GCC's __builtin_prefetch() was introduced a long time ago, all
supported GCC versions have it. Lets do what the big boys up in
linux/prefetch.h do, except we use '1' as the third parameter to
provoke 'PREF 0,...' and 'PREF 1,...' instead of other prefetch
hints.
This allows for better code generation. In theory the existing
embedded asm could be optimized, but the compiler has these builtins,
so there is really no point.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1235/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For the simulator, fake a slow clock to get fast output.
In prom_putchar we have to mask the value so the simulator doesn't
ASSERT when printing non-ASCII characters.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1255/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
ar7_regiser_devices needs ar7_clocks_init to have been called first,
however clock.o is currently linked later due to its order in the Makefile,
therefore ar7_clocks_init always gets called later than ar7_register_devices
because both have the same initcall level. Fix this by moving
ar7_register_devices to the right initcall level.
Reported-by: Michael J. Evans <mjevans1983@gmail.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
To: linux-mips@linux-mips.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1212/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Instead of doing yet another switch/case on the chip_id, use existing
inline function to set the watchdog base address.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1211/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is too generic a name, so prefix it with BCM63XX_ to avoid potential
namespace clashes when including <asm/gpio.h>.
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1171/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Updates the 4G Systems MTX-1 defconfig, and remove systems unavailable
on this platform. Changes include:
- built-in MTD char/block support
- GPIO sysfs support
- MTX-1 watchdog driver
- I2C over GPIO driver as a module
- SquashFS support
Signed-off-by: Florian Fainelli <florian@openwrt.org>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1168/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The _EXL, _KERNEL etc. bits are in the performance control register so
use _PERFCTRL prefix instead of _PERFCNT. While at it make the macro
more readable, use _ENABLE instead of _INT_EN suffix to describe the
interrupt enable bit.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1203/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Unified macro for counter0 and counter1 to set the event in the control
register. This will be needed by Perf.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1200/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The "nofpu" and "nodsp" kernel command line options currently do not
affect CPUs that are brought online later in the boot process or
hotplugged at runtime. It is desirable to apply the nofpu/nodsp options
to all CPUs in the system, so that surprising results are not seen when
a process migrates from one CPU to another.
[Ralf: Moved definitions of mips_fpu_disabled, fpu_disable,
mips_dsp_disabled and dsp_disable from setup.c to cpu-probe.c to allow
making mips_fpu_disabled and mips_dsp_disabled static.]
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: http://patchwork.linux-mips.org/patch/1169/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Modifications to the boot memory allocation structures to make them easier
to read and maintain. Note that this will not pass checkpatch because
it wants a structure element initializer to be enclosed in a
do {...} while(...), which is obvious nonsensical.
Signed-off-by: David VomLehn <dvomlehn@cisco.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1207/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a sysdev for DBDMA PM.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1119/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use a sysdev to implement PM methods for the Au1000 interrupt controllers.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1114/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Clean out stray unused board_reset() calls in pb1x boards, the PB1000 is
different from the rest and gets private methods.
(Cleanup after 32fd6901a6)
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1085/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (92 commits)
powerpc: Remove unused 'protect4gb' boot parameter
powerpc: Build-in e1000e for pseries & ppc64_defconfig
powerpc/pseries: Make request_ras_irqs() available to other pseries code
powerpc/numa: Use ibm,architecture-vec-5 to detect form 1 affinity
powerpc/numa: Set a smaller value for RECLAIM_DISTANCE to enable zone reclaim
powerpc: Use smt_snooze_delay=-1 to always busy loop
powerpc: Remove check of ibm,smt-snooze-delay OF property
powerpc/kdump: Fix race in kdump shutdown
powerpc/kexec: Fix race in kexec shutdown
powerpc/kexec: Speedup kexec hash PTE tear down
powerpc/pseries: Add hcall to read 4 ptes at a time in real mode
powerpc: Use more accurate limit for first segment memory allocations
powerpc/kdump: Use chip->shutdown to disable IRQs
powerpc/kdump: CPUs assume the context of the oopsing CPU
powerpc/crashdump: Do not fail on NULL pointer dereferencing
powerpc/eeh: Fix oops when probing in early boot
powerpc/pci: Check devices status property when scanning OF tree
powerpc/vio: Switch VIO Bus PM to use generic helpers
powerpc: Avoid bad relocations in iSeries code
powerpc: Use common cpu_die (fixes SMP+SUSPEND build)
...
* 'drm-for-2.6.35' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (207 commits)
drm/radeon/kms/pm/r600: select the mid clock mode for single head low profile
drm/radeon: fix power supply kconfig interaction.
drm/radeon/kms: record object that have been list reserved
drm/radeon: AGP memory is only I/O if the aperture can be mapped by the CPU.
drm/radeon/kms: don't default display priority to high on rs4xx
drm/edid: fix typo in 1600x1200@75 mode
drm/nouveau: fix i2c-related init table handlers
drm/nouveau: support init table i2c device identifier 0x81
drm/nouveau: ensure we've parsed i2c table entry for INIT_*I2C* handlers
drm/nouveau: display error message for any failed init table opcode
drm/nouveau: fix init table handlers to return proper error codes
drm/nv50: support fractional feedback divider on newer chips
drm/nv50: fix monitor detection on certain chipsets
drm/nv50: store full dcb i2c entry from vbios
drm/nv50: fix suspend/resume with DP outputs
drm/nv50: output calculated crtc pll when debugging on
drm/nouveau: dump pll limits entries when debugging is on
drm/nouveau: bios parser fixes for eDP boards
drm/nouveau: fix a nouveau_bo dereference after it's been destroyed
drm/nv40: remove some completed ctxprog TODOs
...
* 'dbg-early-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
echi-dbgp: Add kernel debugger support for the usb debug port
earlyprintk,vga,kdb: Fix \b and \r for earlyprintk=vga with kdb
kgdboc: Add ekgdboc for early use of the kernel debugger
x86,early dr regs,kgdb: Allow kernel debugger early dr register access
x86,kgdb: Implement early hardware breakpoint debugging
x86, kgdb, init: Add early and late debug states
x86, kgdb: early trap init for early debug
* 'kdb-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb: (25 commits)
kdb,debug_core: Allow the debug core to receive a panic notification
MAINTAINERS: update kgdb, kdb, and debug_core info
debug_core,kdb: Allow the debug core to process a recursive debug entry
printk,kdb: capture printk() when in kdb shell
kgdboc,kdb: Allow kdb to work on a non open console port
kgdb: Add the ability to schedule a breakpoint via a tasklet
mips,kgdb: kdb low level trap catch and stack trace
powerpc,kgdb: Introduce low level trap catching
x86,kgdb: Add low level debug hook
kgdb: remove post_primary_code references
kgdb,docs: Update the kgdb docs to include kdb
kgdboc,keyboard: Keyboard driver for kdb with kgdb
kgdb: gdb "monitor" -> kdb passthrough
sparc,sunzilog: Add console polling support for sunzilog serial driver
sh,sh-sci: Use NO_POLL_CHAR in the SCIF polled console code
kgdb,8250,pl011: Return immediately from console poll
kgdb: core changes to support kdb
kdb: core for kgdb back end (2 of 2)
kdb: core for kgdb back end (1 of 2)
kgdb,blackfin: Add in kgdb_arch_set_pc for blackfin
...
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (113 commits)
omap4: Add support for i2c init
omap: Fix i2c platform init code for omap4
OMAP2 clock: fix recursive spinlock attempt when CONFIG_CPU_FREQ=y
OMAP powerdomain, hwmod, omap_device: add some credits
OMAP4 powerdomain: Support LOWPOWERSTATECHANGE for powerdomains
OMAP3 clock: add support for setting the divider for sys_clkout2 using clk_set_rate
OMAP4 powerdomain: Fix pwrsts flags for ALWAYS ON domains
OMAP: timers: Fix clock source names for OMAP4
OMAP4 clock: Support clk_set_parent
OMAP4: PRCM: Add offset defines for all CM registers
OMAP4: PRCM: Add offset defines for all PRM registers
OMAP4: PRCM: Remove duplicate definition of base addresses
OMAP4: PRM: Remove MPU internal code name and apply PRCM naming convention
OMAP4: CM: Remove non-functional registers in ES1.0
OMAP: hwmod: Replace WARN by pr_warning for clockdomain check
OMAP: hwmod: Rename hwmod name for the MPU
OMAP: hwmod: Do not exit the iteration if one clock init failed
OMAP: hwmod: Replace WARN by pr_warning if clock lookup failed
OMAP: hwmod: Remove IS_ERR check with omap_clk_get_by_name return value
OMAP: hwmod: Fix wrong pointer iteration in oh->slaves
...
This allows bin_attr->read,write,mmap callbacks to check file specific data
(such as inode owner) as part of any privilege validation.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.infradead.org/mtd-2.6: (154 commits)
mtd: cfi_cmdset_0002: use AMD standard command-set with Winbond flash chips
mtd: cfi_cmdset_0002: Fix MODULE_ALIAS and linkage for new 0701 commandset ID
mtd: mxc_nand: Remove duplicate NAND_CMD_RESET case value
mtd: update gfp/slab.h includes
jffs2: Stop triggering block erases from jffs2_write_super()
jffs2: Rename jffs2_erase_pending_trigger() to jffs2_dirty_trigger()
jffs2: Use jffs2_garbage_collect_trigger() to trigger pending erases
jffs2: Require jffs2_garbage_collect_trigger() to be called with lock held
jffs2: Wake GC thread when there are blocks to be erased
jffs2: Erase pending blocks in GC pass, avoid invalid -EIO return
jffs2: Add 'work_done' return value from jffs2_erase_pending_blocks()
mtd: mtdchar: Do not corrupt backing device of device node inode
mtd/maps/pcmciamtd: Fix printk format for ssize_t in debug messages
drivers/mtd: Use kmemdup
mtd: cfi_cmdset_0002: Fix argument order in bootloc warning
mtd: nand: add Toshiba TC58NVG0 device ID
pcmciamtd: add another ID
pcmciamtd: coding style cleanups
pcmciamtd: fixing obvious errors
mtd: chips: add SST39WF160x NOR-flashes
...
Trivial conflicts due to dev_node removal in drivers/mtd/maps/pcmciamtd.c
Newer code in mm/page_alloc.c requires this function now in arches.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Decode the vast majority of insns that appear in the trace buffer to get a
better idea of what's going on at a glance.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Print out the faulting instruction so when people send traces as part of
bug reports, we have a better idea of what is going on.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Now that the split traps code has moved all the verbose output to the
trace.c file, we can unify all the CONFIG_DEBUG_VERBOSE handling. This
gets rid of much of the crappy ifdef forest and enables usage of normal
pr_xxx functions so checkpatch stops complaining.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The current kernel/traps.c file has grown a bit unwieldy as more debugging
functionality has been added over time, so split it up into more logical
files. There should be no functional changes here, just minor whitespace
tweaking. This should make future extensions easier to manage.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch removes a custom GPIO wakeup API which allowed GPIOs to act
as wakeup sources, which are not configured as Interrupts.
This API is a leftover from the time before irq_wake was established.
From now on people must use enable_irq_wake(GPIO_IRQx) and the GPIO in
question needs to be configured as Interrupt.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
These boards all have the GPIO VRSEL hooked up as an active high.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Now that there's a common header with everything unified, drop the defines
from the global namespace. Pollution sucks.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The empty_bad_page/empty_bad_page_table pages are unused, so punt them.
The zero_page is always allocated, so push it out to the bss to speed up
the booting process a bit and pack data nicer.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
I believe support was disabled due to issues with earlier versions of
the board/processor. At worst, adding the ports back into the device
tree should result in enabling ports that don't work on older systems,
so the default should be to enable them.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is started as swsusp_32.S modifications, but the amount of #ifdefs
made the whole file horribly unreadable, so let's put the support into
its own separate file.
The code should be relatively easy to modify to support 44x BookEs as
well, but since I don't have any 44x to test, let's confine the code to
FSL BookE. (The only FSL-specific part so far is 'flush_dcache_L1'.)
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Most of the MSCR bit assigments are different in e500mc versus
e500, and they are now write-one-to-clear.
Some e500mc machine check conditions are made recoverable (as long as
they aren't stuck on), most notably L1 instruction cache parity errors.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
'protect4gb' boot parameter was introduced to avoid allocating dma
space acrossing 4GB boundary in 2007 (the commit
569975591c).
In 2008, the IOMMU was fixed to use the boundary_mask parameter per
device properly. So 'protect4gb' workaround was removed (the
383af9525b). But somehow I messed the
'protect4gb' boot parameter that was used to enable the
workaround.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The e1000e device is becoming more common these days, so let's just
build it in for pseries & ppc64_defconfig.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
At the moment only the RAS code uses event-sources interrupts (for EPOW
events and internal errors) so request_ras_irqs() (which actually requests
the event-sources interrupts) is found in ras.c and is static.
We want to be able to use event-sources interrupts in other pseries code,
so let's rename request_ras_irqs() to request_event_sources_irqs() and
move it to event_sources.c.
This will be used in an upcoming patch that adds support for IO Event
interrupts that come through as event sources.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I've been told that the architected way to determine we are in form 1
affinity mode is by reading the ibm,architecture-vec-5 property which
mirrors the layout of the fifth vector of the ibm,client-architecture
structure.
Eventually we may want to parse the ibm,architecture-vec-5 and create
FW_FEATURE_* bits.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I noticed /proc/sys/vm/zone_reclaim_mode was 0 on a ppc64 NUMA box. It gets
enabled via this:
/*
* If another node is sufficiently far away then it is better
* to reclaim pages in a zone before going off node.
*/
if (distance > RECLAIM_DISTANCE)
zone_reclaim_mode = 1;
Since we use the default value of 20 for REMOTE_DISTANCE and 20 for
RECLAIM_DISTANCE it never kicks in.
The local to remote bandwidth ratios can be quite large on System p
machines so it makes sense for us to reclaim clean pagecache locally before
going off node.
The patch below sets a smaller value for RECLAIM_DISTANCE and thus enables
zone reclaim.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Right now if we want to busy loop and not give up any time to the hypervisor
we put a very large value into smt_snooze_delay. This is sometimes useful
when running a single partition and you want to avoid any latencies due
to the hypervisor or CPU power state transitions. While this works, it's a bit
ugly - how big a number is enough now we have NO_HZ and can be idle for a very
long time.
The patch below makes smt_snooze_delay signed, and a negative value means loop
forever:
echo -1 > /sys/devices/system/cpu/cpu0/smt_snooze_delay
This change shouldn't affect the existing userspace tools (eg ppc64_cpu), but
I'm cc-ing Nathan just to be sure.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I'm not sure why we have code for parsing an ibm,smt-snooze-delay OF
property. Since we have a smt-snooze-delay= boot option and we can
also set it at runtime via sysfs, it should be safe to get rid of
this code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we are crashing, the crashing/primary CPU IPIs the secondaries to
turn off IRQs, go into real mode and wait in kexec_wait. While this
is happening, the primary tears down all the MMU maps. Unfortunately
the primary doesn't check to make sure the secondaries have entered
real mode before doing this.
On PHYP machines, the secondaries can take a long time shutting down
the IRQ controller as RTAS calls are need. These RTAS calls need to
be serialised which resilts in the secondaries contending in
lock_rtas() and hence taking a long time to shut down.
We've hit this on large POWER7 machines, where some secondaries are
still waiting in lock_rtas(), when the primary tears down the HPTEs.
This patch makes sure all secondaries are in real mode before the
primary tears down the MMU. It uses the new kexec_state entry in the
paca. It times out if the secondaries don't reach real mode after
10sec.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In kexec_prepare_cpus, the primary CPU IPIs the secondary CPUs to
kexec_smp_down(). kexec_smp_down() calls kexec_smp_wait() which sets
the hw_cpu_id() to -1. The primary does this while leaving IRQs on
which means the primary can take a timer interrupt which can lead to
the IPIing one of the secondary CPUs (say, for a scheduler re-balance)
but since the secondary CPU now has a hw_cpu_id = -1, we IPI CPU
-1... Kaboom!
We are hitting this case regularly on POWER7 machines.
There is also a second race, where the primary will tear down the MMU
mappings before knowing the secondaries have entered real mode.
Also, the secondaries are clearing out any pending IPIs before
guaranteeing that no more will be received.
This changes kexec_prepare_cpus() so that we turn off IRQs in the
primary CPU much earlier. It adds a paca flag to say that the
secondaries have entered the kexec_smp_down() IPI and turned off IRQs,
rather than overloading hw_cpu_id with -1. This new paca flag is
again used to in indicate when the secondaries has entered real mode.
It also ensures that all CPUs have their IRQs off before we clear out
any pending IPI requests (in kexec_cpu_down()) to ensure there are no
trailing IPIs left unacknowledged.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently for kexec the PTE tear down on 1TB segment systems normally
requires 3 hcalls for each PTE removal. On a machine with 32GB of
memory it can take around a minute to remove all the PTEs.
This optimises the path so that we only remove PTEs that are valid.
It also uses the read 4 PTEs at once HCALL. For the common case where
a PTEs is invalid in a 1TB segment, this turns the 3 HCALLs per PTE
down to 1 HCALL per 4 PTEs.
This gives an > 10x speedup in kexec times on PHYP, taking a 32GB
machine from around 1 minute down to a few seconds.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds plpar_pte_read_4_raw() which can be used read 4 PTEs from
PHYP at a time, while in real mode.
It also creates a new hcall9 which can be used in real mode. It's the
same as plpar_hcall9 but minus the tracing hcall statistics which may
require variables outside the RMO.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Author: Milton Miller <miltonm@bga.com>
On large machines we are running out of room below 256MB. In some cases we
only need to ensure the allocation is in the first segment, which may be
256MB or 1TB.
Add slb0_limit and use it to specify the upper limit for the irqstack and
emergency stacks.
On a large ppc64 box, this fixes a panic at boot when the crashkernel=
option is specified (previously we would run out of memory below 256MB).
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I saw this in a kdump kernel:
IOMMU table initialized, virtual merging enabled
Interrupt 155954 (real) is invalid, disabling it.
Interrupt 155953 (real) is invalid, disabling it.
ie we took some spurious interrupts. default_machine_crash_shutdown tries
to disable all interrupt sources but uses chip->disable which maps to
the default action of:
static void default_disable(unsigned int irq)
{
}
If we use chip->shutdown, then we actually mask the IRQ:
static void default_shutdown(unsigned int irq)
{
struct irq_desc *desc = irq_to_desc(irq);
desc->chip->mask(irq);
desc->status |= IRQ_MASKED;
}
Not sure why we don't implement a ->disable action for xics.c, or why
default_disable doesn't mask the interrupt.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We wrap the crash_shutdown_handles[] calls with longjmp/setjmp, so if any
of them fault we can recover. The problem is we add a hook to the debugger
fault handler hook which calls longjmp unconditionally.
This first part of kdump is run before we marshall the other CPUs, so there
is a very good chance some CPU on the box is going to page fault. And when
it does it hits the longjmp code and assumes the context of the oopsing CPU.
The machine gets very confused when it has 10 CPUs all with the same stack,
all thinking they have the same CPU id. I get even more confused trying
to debug it.
The patch below adds crash_shutdown_cpu and uses it to specify which cpu is
in the protected region. Since it can only be -1 or the oopsing CPU, we don't
need to use memory barriers since it is only valid on the local CPU - no other
CPU will ever see a value that matches it's local CPU id.
Eventually we should switch the order and marshall all CPUs before doing the
crash_shutdown_handles[] calls, but that is a bigger fix.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we take an EEH error early enough, we oops:
Call Trace:
[c000000010483770] [c000000000013ee4] .show_stack+0xd8/0x218 (unreliable)
[c000000010483850] [c000000000658940] .dump_stack+0x28/0x3c
[c0000000104838d0] [c000000000057a68] .eeh_dn_check_failure+0x2b8/0x304
[c000000010483990] [c0000000000259c8] .rtas_read_config+0x120/0x168
[c000000010483a40] [c000000000025af4] .rtas_pci_read_config+0xe4/0x124
[c000000010483af0] [c00000000037af18] .pci_bus_read_config_word+0xac/0x104
[c000000010483bc0] [c0000000008fec98] .pcibios_allocate_resources+0x7c/0x220
[c000000010483c90] [c0000000008feed8] .pcibios_resource_survey+0x9c/0x418
[c000000010483d80] [c0000000008fea10] .pcibios_init+0xbc/0xf4
[c000000010483e20] [c000000000009844] .do_one_initcall+0x98/0x1d8
[c000000010483ed0] [c0000000008f0560] .kernel_init+0x228/0x2e8
[c000000010483f90] [c000000000031a08] .kernel_thread+0x54/0x70
EEH: Detected PCI bus error on device <null>
EEH: This PCI device has failed 1 times in the last hour:
EEH: location=U78A5.001.WIH8464-P1 driver= pci addr=0001:00:01.0
EEH: of node=/pci@800000020000209/usb@1
EEH: PCI device/vendor: 00351033
EEH: PCI cmd/status register: 12100146
Unable to handle kernel paging request for data at address 0x00000468
Oops: Kernel access of bad area, sig: 11 [#1]
....
NIP [c000000000057610] .rtas_set_slot_reset+0x38/0x10c
LR [c000000000058724] .eeh_reset_device+0x5c/0x124
Call Trace:
[c00000000bc6bd00] [c00000000005a0e0] .pcibios_remove_pci_devices+0x7c/0xb0 (unreliable)
[c00000000bc6bd90] [c000000000058724] .eeh_reset_device+0x5c/0x124
[c00000000bc6be40] [c0000000000589c0] .handle_eeh_events+0x1d4/0x39c
[c00000000bc6bf00] [c000000000059124] .eeh_event_handler+0xf0/0x188
[c00000000bc6bf90] [c000000000031a08] .kernel_thread+0x54/0x70
We called rtas_set_slot_reset while scanning the bus and before the pci_dn
to pcidev mapping has been created. Since we only need the pcidev to work
out the type of reset and that only gets set after the module for the
device loads, lets just do a hot reset if the pcidev is NULL.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Linas Vepstas <linasvepstas@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We ran into an issue where it looks like we're not properly ignoring a
pci device with a non-good status property when we walk the device tree
and instanciate the Linux side PCI devices.
However, the EEH init code does look for the property and disables EEH
on these devices. This leaves us in an inconsistent where we are poking
at a supposedly bad piece of hardware and RTAS will block our config
cycles because EEH isn't enabled anyway.
Signed-of-by: Sonny Rao <sonnyrao@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Switch to use the generic power management helpers.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Subrata Modak reported that building a CONFIG_RELOCATABLE kernel with
CONFIG_ISERIES enabled gives the following warnings:
WARNING: 4 bad relocations
c00000000007216e R_PPC64_ADDR16_HIGHEST __ksymtab+0x00000000009dcec8
c000000000072172 R_PPC64_ADDR16_HIGHER __ksymtab+0x00000000009dcec8
c00000000007217a R_PPC64_ADDR16_HI __ksymtab+0x00000000009dcec8
c00000000007217e R_PPC64_ADDR16_LO __ksymtab+0x00000000009dcec8
The reason is that decrementer_iSeries_masked is using
LOAD_REG_IMMEDIATE to get the address of a kernel symbol, which
creates relocations that aren't handled by the kernel relocator code.
Instead of reading the tb_ticks_per_jiffy variable, we can just set
the decrementer to its maximum value (0x7fffffff) and that will work
just as well. In fact timer_interrupt sets the decrementer to that
value initially anyway, and we are sure to get into timer_interrupt
once interrupts are reenabled because we store 1 to the decrementer
interrupt flag in the lppaca (LPPACADECRINT(r12) here).
Reported-by: Subrata Modak <subrata@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Configuring a powerpc 32 bit kernel for both SMP and SUSPEND turns on
CPU_HOTPLUG to enable disable_nonboot_cpus to be called by the common
suspend code. Previously the definition of cpu_die for ppc32 was in
the powermac platform code, causing it to be undefined if that platform
as not selected.
arch/powerpc/kernel/built-in.o: In function 'cpu_idle':
arch/powerpc/kernel/idle.c:98: undefined reference to 'cpu_die'
Move the code from setup_64 to smp.c and rename the power mac
versions to their specific names.
Note that this does not setup the cpu_die pointers in either
smp_ops (request a given cpu die) or ppc_md (make this cpu die),
for other platforms but there are generic versions in smp.c.
Reported-by: Matt Sealey <matt@genesi-usa.com>
Reported-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The powerpc strncmp implementation does not correctly handle a zero
length, despite the claim in 0119536cd3
(Add hand-coded assembly strcmp).
Additionally, all the length arguments are size_t, not int, so use
PPC_LCMPI and eq instead of cmpwi and le throughout.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There appear to be Pegasos systems which have the rtas-event-scan
RTAS tokens, but on which the event scan always fails. They also
have an event-scan-rate property containing 0, which means call
event scan 0 times per minute.
So interpret a scan rate of 0 to mean don't scan at all. This fixes
the problem on the Pegasos machines and makes sense as well.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits)
qlcnic: adding co maintainer
ixgbe: add support for active DA cables
ixgbe: dcb, do not tag tc_prio_control frames
ixgbe: fix ixgbe_tx_is_paused logic
ixgbe: always enable vlan strip/insert when DCB is enabled
ixgbe: remove some redundant code in setting FCoE FIP filter
ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp
ixgbe: fix header len when unsplit packet overflows to data buffer
ipv6: Never schedule DAD timer on dead address
ipv6: Use POSTDAD state
ipv6: Use state_lock to protect ifa state
ipv6: Replace inet6_ifaddr->dead with state
cxgb4: notify upper drivers if the device is already up when they load
cxgb4: keep interrupts available when the ports are brought down
cxgb4: fix initial addition of MAC address
cnic: Return SPQ credit to bnx2x after ring setup and shutdown.
cnic: Convert cnic_local_flags to atomic ops.
can: Fix SJA1000 command register writes on SMP systems
bridge: fix build for CONFIG_SYSFS disabled
ARCNET: Limit com20020 PCI ID matches for SOHARD cards
...
Fix up various conflicts with pcmcia tree drivers/net/
{pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and
wireless/orinoco/spectrum_cs.c} and feature removal
(Documentation/feature-removal-schedule.txt).
Also fix a non-content conflict due to pm_qos_requirement getting
renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c
Allow kdb to work properly with with earlyprintk=vga by interpreting
the backspace and carriage return output characters. These
interpretation of these characters is used for simple line editing
provided in the kdb shell.
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Ingo Molnar <mingo@redhat.com>
CC: H. Peter Anvin <hpa@zytor.com>
CC: x86@kernel.org
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
If the kernel debugger was configured, attached and started with
kgdbwait, the hardware breakpoint registers should get restored by the
kgdb code which is managing the dr registers.
CC: x86@kernel.org
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Ingo Molnar <mingo@redhat.com>
CC: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
It is not possible to use the hw_breakpoint.c API prior to mm_init(),
but it is possible to use hardware breakpoints with the kernel
debugger.
Prior to smp_init() it is possible to simply write to the dr registers
of the boot cpu directly. This can be used up until the
kgdb_arch_late() is invoked, at which point the standard hw_breakpoint.c
API will get used.
CC: Frederic Weisbecker <fweisbec@gmail.com>
CC: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
The kernel debugger can operate well before mm_init(), but the x86
hardware breakpoint code which uses the perf api requires that the
kernel allocators are initialized.
This means the kernel debug core needs to provide an optional arch
specific call back to allow the initialization functions to run after
the kernel has been further initialized.
The kdb shell already had a similar restriction with an early
initialization and late initialization. The kdb_init() was moved into
the debug core's version of the late init which is called
dbg_late_init();
CC: kgdb-bugreport@lists.sourceforge.net
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Allow the x86 arch to have early exception processing for the purpose
of debugging via the kgdb.
Signed-off-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
The only way the debugger can handle a trap in inside rcu_lock,
notify_die, or atomic_notifier_call_chain without a recursive fault is
to have a low level "first opportunity handler" do_trap_or_bp() handler.
Generally this will be something the vast majority of folks will not
need, but for those who need it, it is added as a kernel .config
option called KGDB_LOW_LEVEL_TRAP.
Also added was a die notification for oops such that kdb can catch an
oops for analysis.
There appeared to be no obvious way to pass the struct pt_regs from
the original exception back to the stack back tracer, so a special
case was added to show_stack() for when kdb is active because you
generally desire to generally look at the back trace of the original
exception.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
The only way the debugger can handle a trap in inside rcu_lock,
notify_die, or atomic_notifier_call_chain without a recursive fault is
to allow the kernel debugger to handle the exception first in
program_check_exception().
The other change here is to make sure that kgdb_handle_exception() is
called with correct parameters when catching an oops, because kdb
needs to know if the entry was an oops, single step, or breakpoint
exception.
[benh@kernel.crashing.org: move debugger_bpt instead of #ifdef]
CC: Paul Mackerras <paulus@samba.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The only way the debugger can handle a trap in inside rcu_lock,
notify_die, or atomic_notifier_call_chain without a triple fault is
to have a low level "first opportunity handler" in the int3 exception
handler.
Generally this will be something the vast majority of folks will not
need, but for those who need it, it is added as a kernel .config
option called KGDB_LOW_LEVEL_TRAP.
CC: Ingo Molnar <mingo@elte.hu>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: H. Peter Anvin <hpa@zytor.com>
CC: x86@kernel.org
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Remove all the references to the kgdb_post_primary_code. This
function serves no useful purpose because you can obtain the same
information from the "struct kgdb_state *ks" from with in the
debugger, if for some reason you want the data.
Also remove the unintentional duplicate assignment for ks->ex_vector.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
These are the minimum changes to the kgdb core in order to enable an
API to connect a new front end (kdb) to the debug core.
This patch introduces the dbg_kdb_mode variable controls where the
user level I/O is routed. It will be routed to the gdbstub (kgdb) or
to the kdb front end which is a simple shell available over the kgdboc
connection.
You can switch back and forth between kdb or the gdb stub mode of
operation dynamically. From gdb stub mode you can blindly type
"$3#33", or from the kdb mode you can enter "kgdb" to switch to the
gdb stub.
The logic in the debug core depends on kdb to look for the typical gdb
connection sequences and return immediately with KGDB_PASS_EVENT if a
gdb serial command sequence is detected. That should allow a
reasonably seamless transition between kdb -> gdb without leaving the
kernel exception state. The two gdb serial queries that kdb is
responsible for detecting are the "?" and "qSupported" packets.
CC: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Martin Hicks <mort@sgi.com>
This patch contains the hooks and instrumentation into kernel which
live outside the kernel/debug directory, which the kdb core
will call to run commands like lsmod, dmesg, bt etc...
CC: linux-arch@vger.kernel.org
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Martin Hicks <mort@sgi.com>
The new debug core api requires all architectures that use to debug
core to implement a function to set the program counter.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Implement kgdb_arch_pc() which adjusts the pc if it needs to be
adjusted after a software breakpoint trap.
Implement kgdb_arch_set_pc() which is a new required function in the
kgdb debug core.
When processing a single step return zero in the error exception field
so that the debug core can distinguish between a single step trap and
a breakpoint trap generically.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
The new debug core api requires all architectures that use to debug
core to implement a function to set the program counter.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: David S. Miller <davem@davemloft.net>
This patch fixes the flush_cache_all for ARMv7 SMP.It was
missing from commit b8349b569a
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: <stable@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It got a typo from 988addf82e.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: <stable@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for 10 hardirq bits to
the ARM architecture. Needed by the SH-Mobile
ARM processor sh7372 that has more than 512 IRQs.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds the clock support to the Nomadik RNG driver
Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: Linus walleij <linus.walleij@stericsson.com>
Acked-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add platform init code for the OMAP3 OHCI driver.
Also, configure padconf settings for OMAP3 depending
on which port mode is used.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
EXTVBUS programming is required by OMAP3EVM REV >=E to supply 500mA
power so adding a flag which can be used by musb driver to program
EXTVBUS.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for i2c init for omap4.
This patch is based on and earlier patch by
Santosh Shilimkar <santosh.shilimkar@ti.com>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add separate omap_i2c_add_bus functions for mach-omap1
and mach-omap2. Make the mach-omap2 init set the interrupt
dynamically to support.
This is needed to add support for omap4 in a way that
works with multi-omap builds. This will eventually get
fixed in a generic way with the omap hwmods.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP2 MPU virtual clock node code attempted to call clk_get_rate()
while the clockfw_lock spinlock was held. Fix by reading the sys_ck
rate directly.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add some missing credits for people who have contributed significant features
or fixes.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Tero Kristo <tero.kristo@nokia.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Thara Gopinath <thara@ti.com>
Some powerdomains in OMAP4 support a direct transition from one sleep
state to another deeper sleep state without having to wakeup the
powerdomain. This patch adds an api in the powerdomain framework to
set the LOWPOWERSTATECHANGE bit in PWRSTCTRL register.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add clock framework support for changing the rate of sys_clkout2.
Signed-off-by: Laine Walker-Avina <lwalkera@ieee.org>
[paul@pwsan.com: added commit message, added .round_rate pointer]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The pwrsts flag for ALWAYS ON domains like always_on_core_pwrdm
and wkup_pwrdm is wrongly populated with the define for a
powerdomain power state, instead of the allowable state
bitfields.
This causes a few api's to fail sensing invalid pwrst
requested.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The clock sources for timers on OMAP4 (system clock and 32k
clock) have their names wronly populated.
This patch fixes them so the omap_dm_timer_set_source
does not fail anymore.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Remove the hack put in place while clock framework was still not in
place for OMAP4.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The cm44xx.h files only had absolute register address
defines for all CM registers.
This patch adds additional register offset defines for all the
registers, so they can be used with apis like cm_read_mod_*
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The prm44xx.h files only had absolute register address
defines for all PRM registers.
This patch adds additional register offset defines for all the
registers, so they can be used with apis like prm_read_mod_*
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
CM1, CM2, PRM, SCRM and MPU_PRCM are already defined in omap44xx.h
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
The MPU subsystem was named based on internal code name (CHIRON).
This patch will remove all the occurences of the chiron name
are replace it with PRCM_MPU in order to differentiate
the MPU local PRCM to the global one.
Remove PDA_ from PRCM_MPU registers names to stick to the global
PRM naming convention.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
The automatic HW restore from OFF mode is not functional at all in
OMAP4430 ES1.0.
Because of that, it will be extensively changed in the next Si revision,
and the compatibilty will not be maintained with ES1.0.
Remove the current XXX_RESTORE registers definition to avoid future
conflicts with the next Si revision.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Most of the clock nodes belong to a clock domain, but it is perfectly valid
to have clock without clock domain.
Root clocks for example does not belong to any clock domain.
Keep the warning but reduce the verbosity.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In the lastest OMAP4 hwmod data file, the _hwmod was removed
in order to save some memory space and because it does not
bring a lot.
The same cleanup will be have to done for other hwmods in
OMAP2 & 3 data files.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
During the _init_clocks phase, the iteration is stopped but the
status is still change from _HWMOD_STATE_REGISTERED to
_HWMOD_STATE_CLKS_INITED.
Since the _setup phase will be done nevertheless, it might be
better to keep initializing the others clocks nodes and just
keep the warning.
It is much easier to debug when a important number of clocks
name are wrong during the early debug phase of a new platform.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The WARN is a little bit too verbose and is not providing
usefull information in that case.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The previous clock API was returning a standard linux error code in
case of failure. This is not the case anymore with the new
omap_clk_get_by_name API. A NULL value means that the clock node
does not exist.
Replace all the IS_ERR check by a !clk check.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The iteration is currently done on the omap_hwmod_ocp_if pointer
and not on the table pointer that reference them.
It worked most of the time because the structure are contiguous in
memory.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some initiator modules in OMAP2 & 3 does not have IDLEST bit,
in that case we cannot detect the module readiness by
polling that bit and must exist the function immediately
assuming that the module is ready.
The previous flag was affected to the OCP interface. While it is
technically true that the idlest is related to the L4 slave
interface of the module, the PRCM status belong to the module.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The return of the omap4_cm_wait_module_ready function is checked
in order to avoid accessing the sysconfig register if the module is
not in the correct state.
In that case the _setup will exit without trying to reset
using sysconfig.
For the moment a warning is printed. A proper management of fclk
and module reset will have to be done in order to init correctly
the problematic IPs listed below.
<4>omap_hwmod: ivahd: cannot be enabled (3)
<4>omap_hwmod: iss: cannot be enabled (3)
<4>omap_hwmod: tesla: cannot be enabled (3)
<4>omap_hwmod: sdma: cannot be enabled (3)
<4>omap_hwmod: sl2: cannot be enabled (3)
<4>omap_hwmod: sad2d: cannot be enabled (3)
<4>omap_hwmod: ducati: cannot be enabled (3)
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The maximum timeout to wait for the PRCM to request that a module
exit idle or reach functionnal state is common to OMAP2/3/4 SoCs,
so, move it to the chip family-common cm.h include file.
Reduce the timeout from 20 ms to 2 ms.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Accessing the clkctrl register using offset of module & device is hard
to do in OMAP4 due to the way the CM1, CM2, PRM and PRCM_MPU are located
in the address space. There is no common base address anymore for all the
CM registers.
The easiest way to handle that on OMAP4 is to provide the absolute address
of the XXX_CLKCTRL register per hwmod.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Clean up comment style, remove unnecessary includes, and resolve some
checkpatch warnings in plat-omap/clock.c.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 678bc9a2ea split dpll4_m2_ck,
creating a 34xx and a 36xx variant, to handle the additional 16
divider steps provided on the 36xx. This in turn required dynamic
rewriting of the clock tree during initialization, which is
undesirable. All this seems to be unnecessary, though, since the
additional 16 divider steps can simply be marked with RATE_IN_36XX.
This patch does so and re-merges the affected structures.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Vishwanath Sripathy <vishwanath.bs@ti.com>
Rename the RATE_IN_343X clksel_rate.rate flag to be RATE_IN_3XXX, to reflect
that these rates are valid on all OMAP3 platforms, not just 343X.
Also rename the RATE_IN_OMAP3430ES2 clksel_rate.rate flag to be
RATE_IN_OMAP3430ES2PLUS, to reflect that these flags are valid on all
OMAP3 platforms after 3430ES2.
This patch should not result in any functional changes.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Ranjith Lohithakshan <ranjithl@ti.com>
This patch cleans up arch/arm/mach-omap2/clkt_clksel.c. It:
- makes several functions static that are not called outside the file;
- adds documentation;
- makes some code paths easier to read (hopefully), by breaking up
compound statements and removing redundant checks;
- converts some pr_err()s that indicate clock tree data problems into WARN()s,
so they are more likely to be noticed;
- and moves omap2_clk_round_rate() back into mach-omap2/clock.c, its proper
home, since it is not clksel-specific.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The DEFAULT_RATE clksel_rate flag is essentially useless. It was set
on some of the lowest divisors, which, when switching to a much
higher-rate parent, could have potentially resulted in rates that
exceeded the hardware specifications for downstream clocks in the
window between the clk_set_parent(), and a subsequent clk_set_rate().
It seems much safer to just remove the flag and always use the highest
available divisor (resulting in the lowest possible rate) after the
switch, and this patch does so.
Ideally, it would be best to first attempt to switch to a divisor that
matches the clock's rate with the previous parent, if at all possible.
But that is a project for some other day or some other person. The
parent changing code is rarely used.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Writes to the PM_*GRPSEL registers should use _GRPSEL_ macros, not _EN_ macros,
to match the TRM and guard against inadvertent error. This patch should
not cause any functional change.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Jouni Högander <jouni.hogander@nokia.com>
Fix all of the remaining PRCM register shift/bitmask macros that did not
use the _SHIFT/_MASK suffixes to use them. This makes the use of these
macros consistent. It is intended to reduce error, as code can be inspected
visually by reviewers to ensure that bitshifts and bitmasks are used in
the appropriate places.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Fix all of the remaining OMAP3 PRCM register shift/bitmask macros that
did not use the _SHIFT/_MASK suffixes to use them. This makes the use
of these macros consistent. It is intended to reduce error, as code
can be inspected visually by reviewers to ensure that bitshifts and
bitmasks are used in the appropriate places.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Fix all of the remaining OMAP2 PRCM register shift/bitmask macros that
did not use the _SHIFT/_MASK suffixes to use them. This makes the use
of these macros consistent. It is intended to reduce error, as code
can be inspected visually by reviewers to ensure that bitshifts and
bitmasks are used in the appropriate places.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
remove the section annotation from omap1_clk_disable_unused()
to kill the section mismatch warning.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
- Update the omap3_defconfig to sync up with the generated .config
- Increase CONFIG_LOG_BUF_SHIFT to 16 to allow the entire
boot log to be captured
(useful when using boot time tracer, for example)
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In OMAP4, MMC1 PBIAS and its associated IO is software-controlled
by CONTROL_PBIAS and CONTROL_MMC1 registers. This patch adds PBIAS
configuration for MMC1 Controller during power-ON and power-OFF
of regulator.
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adding support for MMC1 & MMC2 controllers of OMAP4430 SDP
to board file.
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch enables RTC and regulator support on omap4430 sdp
platform. Also sync up the defconfig with latest kernel
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds i2c1 peripherals data to
omap4430 sdp board file.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds the i2c board support for OMAP4430 SDP platform.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are three i2c buses on am3517, and each i2c bus has several devices
on it, so we can't name the i2c boardinfo structures with one of these
devices. In order to make it more readable, now rename these three boardinfo
structures based on i2c indexes.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Acked-By: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Access to some of the OMAP4 GPIO registers are not properly handled.
This patch fixes it.
This patch is tested on 3430SDP and 4430SDP boards
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch moves OMAP4 soc specific code from 4430sdp board file.
The change is necessary so that newer board support can be added
with minimal changes. This will be also problematic for
multi-board, multi-omap builds.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM3517 don't have the register OMAP343X_CONTROL_PBIAS_LITE and the regulators
like "vmmc", so we set a noop "set_power" function for it.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is two gpio for mmc use, one is for card detecting, another is
used for checking write protect. Intialize its pinmux in case the bootloader
doesn't set it.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Multi line comments are fixed as per CodingStyle
guidelines.
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Manjunatha GK <manjugk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If we are softbooting another kernel using kexec, DMA controller state is not
known when we are performing omap_init_dma(). It is possible that some DMA
channels are already active. For example after kexec we get:
<4>IRQ 0020 for non-allocated DMAchannel 5
<4>IRQ 0020 for non-allocated DMAchannel 5
<4>IRQ 0020 for non-allocated DMAchannel 5
<4>IRQ 0020 for non-allocated DMAchannel 5
<4>IRQ 0020 for non-allocated DMAchannel 5
To prevent any weird things happening, we disable all channel interrupts during
init.
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The SDI Display subsystem needs access to the vdds_sdi supply
regulator. This is TWL4030's VAUX1 supply on RX-51.
Signed-off-by: Roger Quadros <roger.quadros@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
The patch adds a CONFIG directive required for supporting the Amstrad Delta
connected external keyboard by default.
Created and tested against linux-omap master,
commit 104a77440f05430f29f9d3f4ecb88c1536819585 dated 2010-04-27.
Works on top of PATCH v4 4/5(7), "input: serio: add support for Amstrad Delta
serial keyboard port".
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
EHCI port on UI card and LCD share two pins (GPIO 181 and 182) thus
they have to be mutually exclusive.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Upcoming change to tlv320aic3x codec driver require four supplies.
Implement this by connecting analogic supplies to TWL4030 VMMC2 and digital
supplies to TWL4030 VIO.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This makes possible to probe the audio codec and add another i2c2
components in the future.
Fix also indentation for the first omap_register_i2c_bus.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
I believe the VMMC2 constraints must be the same than with VAUX3. Older
boards are using TWL4030 VMMC2 supply for internal MMC whereas newer are
using VAUX3 that has more limited constraints defined in this same file.
More over, the VMMC2 supply is used also for analog audio domain and the
miminum analog voltage of the TLV320AIC34 codec is 2.7 V.
To combine these two facts, the patch changes supply name to V28_A as the
newer boards register VMMC2_30 for VAUX3 and uses the same constraints than
VAUX3 since those constraints are ok for the TLV320AIC34.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some Overo add-on boards include a second ethernet port. This patch
adds support for that second port.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update the default configuration for AM3517EVM to enable
support for EMAC peripheral.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The emac driver currently uses Davinci clock names for the module and phy
clocks. Updated the omap3xxx_clks table to match the names
used by the Davinci emac driver.
Note that eventually the EMAC clocks should be renamed to be generic.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
[tony@atomide.com: updated patch description to match the patch]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Modify the default kernel configuration on AM3517 to enable CAN.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates the new default configuration for the Devkit8000.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Configuration for OMAP2430 should select ARCH_OMAP_OTG just like
it is done for OMAP2420
Signed-off-by: Viral Mehta <viral.mehta@lntinfotech.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add platform init code for OHCI USB on OMAP2430 SDP
Signed-off-by: Viral Mehta <viral.mehta@lntinfotech.com>
[tony@atomide.com: Updated subject to mention the board name]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The patch provides the following ams_delta_defconfig updates:
- explicitly select preemptable RCU,
- replace outdated CONFIG_LBD and CONFIG_LSF options with CONFIG_LBDAF,
- activate support for LCD contrast setting (new in 2.6.34),
- turn off verbose bug reporting for smaller kernel.
Created and tested against linux-2.6.34-rc3.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'acpica' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (22 commits)
ACPI: fix early DSDT dmi check warnings on ia64
ACPICA: Update version to 20100428.
ACPICA: Update/clarify some parameter names associated with acpi_handle
ACPICA: Rename acpi_ex_system_do_suspend->acpi_ex_system_do_sleep
ACPICA: Prevent possible allocation overrun during object copy
ACPICA: Split large file, evgpeblk
ACPICA: Add GPE support for dynamically loaded ACPI tables
ACPICA: Clarify/rename some root table descriptor fields
ACPICA: Update version to 20100331.
ACPICA: Minimize the differences between linux GPE code and ACPICA code base
ACPI: add boot option acpi=copy_dsdt to fix corrupt DSDT
ACPICA: Update DSDT copy/detection.
ACPICA: Add subsystem option to force copy of DSDT to local memory
ACPICA: Add detection of corrupted/replaced DSDT
ACPICA: Add write support for DataTable operation regions
ACPICA: Fix for acpi_reallocate_root_table for incorrect root table copy
ACPICA: Update comments/headers, no functional change
ACPICA: Update version to 20100304
ACPICA: Fix for possible fault in acpi_ex_release_mutex
ACPICA: Standardize integer output for ACPICA warnings/errors
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (250 commits)
ALSA: hda: Storage class should be before const qualifier
ASoC: tpa6130a2: Remove CPVSS and HPVdd supplies
ASoC: tpa6130a2: Define output pins with SND_SOC_DAPM_OUTPUT
ASoC: sdp4430 - add sdp4430 pcm ops to DAI.
ASoC: TWL6040: Enable earphone path in codec
ASoC: SDP4430: Add support for Earphone speaker
ASoC: SDP4430: Add sdp4430 machine driver
ASoC: tlv320dac33: Avoid powering off while in BIAS_OFF
ASoC: tlv320dac33: Use dev_dbg in dac33_hard_power function
ALSA: sound/pci/asihpi: Use kzalloc
ALSA: hdmi - dont fail on extra nodes
ALSA: intelhdmi - add id for the CougarPoint chipset
ALSA: intelhdmi - user friendly codec name
ALSA: intelhdmi - add dependency on SND_DYNAMIC_MINORS
ALSA: asihpi: incorrect range check
ALSA: asihpi: testing the wrong variable
ALSA: es1688: add pedantic range checks
ARM: McBSP: Add support for omap4 in McBSP driver
ARM: McBSP: Fix request for irq in OMAP4
OMAP: McBSP: Add 32-bit mode support
...
* 'for-linus/i2c-2635' of git://git.fluff.org/bjdooks/linux: (21 commits)
i2c-highlander: remover superflous variable
i2c-ibm-iic: drop NO_IRQ
i2c-cpm: drop NO_IRQ
i2c-mpc: drop NO_IRQ
MAINTAINERS: add i2c tree for embedded platforms
i2c-pxa: only define 'blue_murder'-function if DEBUG is #defined
i2c-pxa: remove unused macro
i2c-nomadik: fix operator precedence warning
i2c-nomadik: release region when removed
OMAP3: I2C: Clean up Errata 1p153 handling
OMAP2/3: I2C: Errata ID i207: Clear wrong RDR interrupt
omap: i2c: add a timeout to the busy waiting
omap: i2c: make errata 1.153 workaround a separate function
i2c-omap: add mpu wake up latency constraint in i2c
omap: i2c: Add i2c support on omap4 platform
i2c-bfin-twi: return completion in interrupt for smbus quick transfers
i2c-bfin-twi: remove redundant retry
i2c-bfin-twi: fix lost interrupts at high speeds
i2c-bfin-twi: add debug output for error status
i2c-bfin-twi: integrate timeout timer with completion interface
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (44 commits)
vlynq: make whole Kconfig-menu dependant on architecture
add descriptive comment for TIF_MEMDIE task flag declaration.
EEPROM: max6875: Header file cleanup
EEPROM: 93cx6: Header file cleanup
EEPROM: Header file cleanup
agp: use NULL instead of 0 when pointer is needed
rtc-v3020: make bitfield unsigned
PCI: make bitfield unsigned
jbd2: use NULL instead of 0 when pointer is needed
cciss: fix shadows sparse warning
doc: inode uses a mutex instead of a semaphore.
uml: i386: Avoid redefinition of NR_syscalls
fix "seperate" typos in comments
cocbalt_lcdfb: correct sections
doc: Change urls for sparse
Powerpc: wii: Fix typo in comment
i2o: cleanup some exit paths
Documentation/: it's -> its where appropriate
UML: Fix compiler warning due to missing task_struct declaration
UML: add kernel.h include to signal.c
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
ia64: add sparse annotation to __ia64_per_cpu_var()
percpu: implement kernel memory based chunk allocation
percpu: move vmalloc based chunk management into percpu-vm.c
percpu: misc preparations for nommu support
percpu: reorganize chunk creation and destruction
percpu: factor out pcpu_addr_in_first/reserved_chunk() and update per_cpu_ptr_to_phys()
Add support for wakeup-mask style interrupts that share a
single mask register for various different interrupts. This
registers a set of interrupt->bit mappings and the register
they belong to.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Change local_irq disable calls to use spinlocks to ensure that the
ADC driver data is protected against multiple access..
Note, this does not protect the client's data, and the client should
ensure it does not make multiple calls to the ADC driver.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the new locking calls to ensure that these are always exclusively
accessing the GPIO registers.
Fixes a possible race between two threads modifying the same GPIO bank,
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Ensure the ADC device is touched only if S3C_DEV_ADC
is selected.
Fixes:
arch/arm/mach-s5pv210/built-in.o: In function `s5pv210_map_io':
/home/kgene/bjdooks/arch/arm/mach-s5pv210/cpu.c:92: undefined reference to `s3c_device_adc'
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fixup commit 5cfc8ee0bb which
introduced ARCH_USES_GETTIMEOFFSET but missed out several
S5P architectures.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds support for Watchdog timer for Samsung S5PV210.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds support for Watchdog timer for Samsung S5P6440.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds support for Watchdog timer for Samsung S3C6410
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch moves the definitions of watchdog timer device from
plat-s3c24xx to plat-samsung. This will enable all Samsung S3C
and S5P series SoC's to use common WDT device definition.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This adds new machine definitions for the SmartQ 5 and 7.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Define platform devices for all audio devices found on S5PC100
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This is for samsung GONI board using s5pc110.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds sdhci platform helpers required by sdhci-s3c driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds I2C platform helpers required by s3c2440-i2c driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds common framebuffer device helpers and register defines
for S5PV210 based machines.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds setup code for Samsung OneNAND controller driver. The
driver needs to be aware on which SoC it is running, so the actual
device id is being changed in cpu init code. S3C64xx SoCs have 2 OneNAND
controllers while S5PC100 and S5PC110 has only one.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[ben-linux@fluff.org: sort map.h entries]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch removes all obsolete files from plat-s5pc1xx. This directory is
no longer needed. S5PC100 SoC is now completely supported in plat-s5p
framework.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch moves support for gpio interrupts from plat-s5pc1xx to
mach-s5pc100 directory.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch moves S5PC100 SoC support to plat-s5p framework. Most
periperal support code has been already moved from plat-s5pc1xx to
mach-s5pc100.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move sdhci helpers from plat-s5pc1xx to mach-s5pc100.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds required platform definitions to enable s3c-fb
driver. Two framebuffer windows in 480x800x16bpp mode are defined.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add basic support for Samsung Aquila board. This board is based
on S5PC110 SoC.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The arch/arm/mach-s5pv210/Kconfig had a choice entry
to choose which of the two machines to build, which is
silly since you can easily build more than one machine
at a time.
Remove the choice entry so that both machines and any
future additions can all build in harmony.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch introduces nice defines for the initial values for UART devices
on SMDKC100.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The definition of the framebuffer parameters was created when s3c-fb.c
driver was patched to support setting the refresh rate directly (commit
600ce1a0fa). That patch was completely wrong
and was reverted in commit eb29a5cc0b what breaked the
framebuffer on s5pc100. This patch updates framebuffer definitions to
correct values.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add support for external interrupts on S5PV210.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Pannaga Bhushan <p.bhushan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
[ben-linux@fluff.org: Ext => IRQ_EINT in title]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds touchscreen support for S5PV210.
Note: TSADC in S5PV210 support 2 touchscreen interfaces,
Only 1 is implemented as of now.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
[ben-linux@fluff.org: minor title fix]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds touchscreen support for S5P6440.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
[ben-linux@fluff.org: minor header fix]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds touchscreen support for S3C64XX.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
[ben-linux@fluff.org: minor title fix]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Traditionally, fatal MCE will cause Linux print error log to console
then reboot. Because MCE registers will preserve their content after
warm reboot, the hardware error can be logged to disk or network after
reboot. But system may fail to warm reboot, then you may lose the
hardware error log. ERST can help here. Through saving the hardware
error log into flash via ERST before go panic, the hardware error log
can be gotten from the flash after system boot successful again.
The fatal MCE processing procedure with ERST involved is as follow:
- Hardware detect error, MCE raised
- MCE read MCE registers, check error severity (fatal), prepare error record
- Write MCE error record into flash via ERST
- Go panic, then trigger system reboot
- System reboot, /sbin/mcelog run, it reads /dev/mcelog to check flash
for error record of previous boot via ERST, and output and clear
them if available
- /sbin/mcelog logs error records into disk or network
ERST only accepts CPER record format, but there is no pre-defined CPER
section can accommodate all information in struct mce, so a customized
section type is defined to hold struct mce inside a CPER record as an
error section.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Generic Hardware Error Source provides a way to report platform
hardware errors (such as that from chipset). It works in so called
"Firmware First" mode, that is, hardware errors are reported to
firmware firstly, then reported to Linux by firmware. This way, some
non-standard hardware error registers or non-standard hardware link
can be checked by firmware to produce more valuable hardware error
information for Linux.
Now, only SCI notification type and memory errors are supported. More
notification type and hardware error type will be added later. These
memory errors are reported to user space through /dev/mcelog via
faking a corrected Machine Check, so that the error memory page can be
offlined by /sbin/mcelog if the error count for one page is beyond the
threshold.
On some machines, Machine Check can not report physical address for
some corrected memory errors, but GHES can do that. So this simplified
GHES is implemented firstly.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'timers-for-linus-hpet' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, hpet: Add reference to chipset erratum documentation for disable-hpet-msi-quirk
x86, hpet: Restrict read back to affected ATI chipsets
* 'timers-for-linus-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
avr32: Fix typo in read_persistent_clock()
sparc: Convert sparc to use read/update_persistent_clock
cris: Convert cris to use read/update_persistent_clock
m68k: Convert m68k to use read/update_persistent_clock
m32r: Convert m32r to use read/update_peristent_clock
blackfin: Convert blackfin to use read/update_persistent_clock
ia64: Convert ia64 to use read/update_persistent_clock
avr32: Convert avr32 to use read/update_persistent_clock
h8300: Convert h8300 to use read/update_persistent_clock
frv: Convert frv to use read/update_persistent_clock
mn10300: Convert mn10300 to use read/update_persistent_clock
alpha: Convert alpha to use read/update_persistent_clock
xtensa: Fix unnecessary setting of xtime
time: Clean up direct xtime usage in xen
While waiting for completion of the i2c transfer, the
MPU could hit OFF mode and cause several msecs of
delay that made i2c transfers fail more often. The
extra delays and subsequent re-trys cause i2c clocks
to be active more often. This has also an negative
effect on power consumption.
Created a mechanism for passing and using the
constraint setting function in driver code. The used
mpu wake up latency constraints are now set individually
per bus, and they are calculated based on clock rate
and fifo size.
Thanks to Jarkko Nikula, Moiz Sonasath, Paul Walmsley,
and Nishanth Menon for tuning out the details of
this patch.
Updates by Kevin as requested by Tony:
- Remove omap_set_i2c_constraint_func() in favor of conditionally
adding the flag in omap_i2c_add_bus() in order to keep all the OMAP
conditional checking in a single location.
- Update set_mpu_wkup_lat prototypes to match OMAP PM layer so
OMAP PM function can be used directly in pdata.
Cc: Moiz Sonasath <m-sonasath@ti.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc: Define ARCH_SLAB_MINALIGN
drivers/sbus/char/flash.c: flash_read should update ppos instead of file->f_pos
sparc64: Fix stack dumping and tracing when function graph is enabled.
sparc64: Show stack backtrace from show_regs() just like other platforms.
* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (48 commits)
Revert "rtc: omap: let device wakeup capability be configured from chip init logic"
DM365: Added more PINMUX configurations for AEMIF
DM365: Make CLKOUTx available
DM365: Added PINMUX definitions for GPIO30..32
Davinci: iotable based ioremap() interception
Davinci: pinmux - use ioremap()
Davinci: aintc/cpintc - use ioremap()
Davinci: psc - use ioremap()
Davinci: timer - use ioremap()
Davinci: jtag_id - use ioremap()
Davinci: da8xx: rtc - use ioremap
Davinci: gpio - use ioremap()
davinci: edma: fix coding style issue related to breaking lines
davinci: edma: use BIT() wherever possible
davinci: edma: fix coding style issue related to usage of braces
davinci: edma: use a more intuitive name for edma_info
Davinci: serial - conditional reset via pwremu
Davinci: serial - use ioremap()
Davinci: serial - remove unnecessary define
Davinci: watchdog reset separation across socs
...
Fix up trivial conflict in arch/arm/Kconfig due to removal of "select
GENERIC_TIME"
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Drop duplicated "config IOMMU_HELPER"
[IA64] invoke oom-killer from page fault
[IA64] use __ratelimit
[IA64] Use set_cpus_allowed_ptr
[IA64] Use set_cpus_allowed_ptr
[IA64] arch/ia64/hp/common/sba_iommu.c: Rename dev_info to adi
[IA64] removing redundant ifdef
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (224 commits)
ARM: remove 'select GENERIC_TIME'
ARM: 6136/1: ARCH_REQUIRE_GPIOLIB selects GENERIC_GPIO
ARM: 6074/1: oprofile: convert from sysdev to platform device
ARM: 6073/1: oprofile: remove old files and update KConfig
ARM: 6072/1: oprofile: use perf-events framework as backend
ARM: 6071/1: perf-events: allow modules to query the number of hardware counters
ARM: 6070/1: perf-events: add support for xscale PMUs
ARM: 6069/1: perf-events: use numeric ID to identify PMU
ARM: 6064/1: pmu: register IRQs at runtime
ARM: Optionally allow ARMv6 to use 'normal, bufferable' memory for DMA
ARM: 6134/1: Handle instruction cache maintenance fault properly
ARM: nwfpe: allow debugging output to be configured at runtime
ARM: rename mach_cpu_disable() to platform_cpu_disable()
ARM: 6132/1: PL330: Add common core driver
ARM: 6094/1: Extend cache-l2x0 to support the 16-way PL310
ARM: Move memory mapping into mmu.c
ARM: Ensure meminfo is sorted prior to sanity_check_meminfo
ARM: Remove useless linux/bootmem.h includes
ARM: convert /proc/cpu/aligment to seq_file
arm: use asm-generic/scatterlist.h
...
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (127 commits)
sh: update defconfigs.
sh: Fix up the NUMA build for recent LMB changes.
sh64: provide a stub per_cpu_trap_init() definition.
sh: fix up CONFIG_KEXEC=n build.
sh: fixup the docbook paths for clock framework shuffling.
driver core: Early dev_name() depends on slab_is_available().
sh: simplify WARN usage in SH clock driver
sh: Check return value of clk_get on ms7724
sh: Check return value of clk_get on ecovec24
sh: move sh clock-cpg.c contents to drivers/sh/clk-cpg.c
sh: move sh clock.c contents to drivers/sh/clk.
sh: move sh asm/clock.h contents to linux/sh_clk.h V2
sh: remove unused clock lookup
sh: switch boards to clkdev
sh: switch sh4-202 to clkdev
sh: switch shx3 to clkdev
sh: switch sh7757 to clkdev
sh: switch sh7763 to clkdev
sh: switch sh7780 to clkdev
sh: switch sh7786 to clkdev
...
This patch adds also the pin definition helpers in iomux-mx3.h
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Move the arch/arm/mach-s3c64xx/dev-ts.c file to arch/arm/plat-samsung and
rename the Kconfig entry appropriately.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch implements cfg_gpio function for Samsung touchscreen.
And also modifies the H1940 machine respectively.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds the touchscreen platform device definition for S3C64XX boards.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This moves mach-s3c2410/include/mach/ts.h to plat-samsung/include/plat/ts.h in
order to prepare for s3c64xx support in the touchscreen driver.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move i2c helpers from plat-s5pc1xx to mach-s5pc100.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move frame buffer helpers from plat-s5pc1xx to mach-s5pc100.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch renames gpio related registers from s5pc1xx to s5pc100 to
better match the plat-s5p framework style. GPIO_MP* defines now used
anywhere thus has been removed.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move gpio-lib support from plat-s5pc1xx to mach-s5pc100. Only basic gpio
functionality is now supported. Gpio interrupts are disabled temporarly
and will be added later.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
GPIOlib helpers from plat-samsung already have functions for accessing
4bit gpio banks. This patch removes the duplicated functions from
plat-s5pc1xx/gpiolib.c.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This is a pre-requisite clock patch for the plat-s5pc1xx to plat-s5p
movement. The patches that perform the movement of the code from
plat-s5pc1xx to plat-s5p (and mach-s5pc100) should also enable the
build for the mach-s5pc100/clock.c code.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Driver strength parameter can be changed not only on S5PC100 but also
on S5PV210/S5PC110 platforms, so move the helper functions to the common
plat-samsung directory.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds GPIOlib support for S5PV210.
Signed-off-by: Pannaga Bhushan <p.bhushan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Timer interrupts range was defined as 43-47, what overlaps with VIC0 range
(32-64). This was caused probably by a typo while the common interrupts
definition was refactored. This patch moves timer interrupt range to safe
area of 11-15 (just before uart range).
This fixes the commit 87aef30eb3
("ARM: S5P: Change S5P_TIMER_IRQ based to 11 for SAMSUNG S5P series.")
which meant to move these into the old (and previously reserved)
ISA space.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[ben-linux@fluff.org: update description]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
When cr0.wp=0, we may shadow a gpte having u/s=1 and r/w=0 with an spte
having u/s=0 and r/w=1. This allows excessive access if the guest sets
cr0.wp=1 and accesses through this spte.
Fix by making cr0.wp part of the base role; we'll have different sptes for
the two cases and the problem disappears.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
kvm_x86_ops->set_efer() would execute vcpu->arch.efer = efer, so the
checking of LMA bit didn't work.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
The current lmsw implementation allows the guest to clear cr0.pe, contrary
to the manual, which breaks EMM386.EXE.
Fix by ORing the old cr0.pe with lmsw's operand.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch puts up the flag that tells the guest that we'll warn it
about the tsc being trustworthy or not. By now, we also say
it is not.
Signed-off-by: Glauber Costa <glommer@redhat.com>
Acked-by: Zachary Amsden <zamsden@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
If the HV told us we can fully trust the TSC, skip any
correction
Signed-off-by: Glauber Costa <glommer@redhat.com>
Acked-by: Zachary Amsden <zamsden@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
We now added a new set of clock-related msrs in replacement of the old
ones. In theory, we could just try to use them and get a return value
indicating they do not exist, due to our use of kvm_write_msr_save.
However, kvm clock registration happens very early, and if we ever
try to write to a non-existant MSR, we raise a lethal #GP, since our
idt handlers are not in place yet.
So this patch tests for a cpuid feature exported by the host to
decide which set of msrs are supported.
Signed-off-by: Glauber Costa <glommer@redhat.com>
Acked-by: Zachary Amsden <zamsden@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Right now, we were using individual KVM_CAP entities to communicate
userspace about which cpuids we support. This is suboptimal, since it
generates a delay between the feature arriving in the host, and
being available at the guest.
A much better mechanism is to list para features in KVM_GET_SUPPORTED_CPUID.
This makes userspace automatically aware of what we provide. And if we
ever add a new cpuid bit in the future, we have to do that again,
which create some complexity and delay in feature adoption.
Signed-off-by: Glauber Costa <glommer@redhat.com>
Acked-by: Zachary Amsden <zamsden@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This cpuid, KVM_CPUID_CLOCKSOURCE2, will indicate to the guest
that kvmclock is available through a new set of MSRs. The old ones
are deprecated.
Signed-off-by: Glauber Costa <glommer@redhat.com>
Acked-by: Zachary Amsden <zamsden@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Avi pointed out a while ago that those MSRs falls into the pentium
PMU range. So the idea here is to add new ones, and after a while,
deprecate the old ones.
Signed-off-by: Glauber Costa <glommer@redhat.com>
Acked-by: Zachary Amsden <zamsden@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
In recent stress tests, it was found that pvclock-based systems
could seriously warp in smp systems. Using ingo's time-warp-test.c,
I could trigger a scenario as bad as 1.5mi warps a minute in some systems.
(to be fair, it wasn't that bad in most of them). Investigating further, I
found out that such warps were caused by the very offset-based calculation
pvclock is based on.
This happens even on some machines that report constant_tsc in its tsc flags,
specially on multi-socket ones.
Two reads of the same kernel timestamp at approx the same time, will likely
have tsc timestamped in different occasions too. This means the delta we
calculate is unpredictable at best, and can probably be smaller in a cpu
that is legitimately reading clock in a forward ocasion.
Some adjustments on the host could make this window less likely to happen,
but still, it pretty much poses as an intrinsic problem of the mechanism.
A while ago, I though about using a shared variable anyway, to hold clock
last state, but gave up due to the high contention locking was likely
to introduce, possibly rendering the thing useless on big machines. I argue,
however, that locking is not necessary.
We do a read-and-return sequence in pvclock, and between read and return,
the global value can have changed. However, it can only have changed
by means of an addition of a positive value. So if we detected that our
clock timestamp is less than the current global, we know that we need to
return a higher one, even though it is not exactly the one we compared to.
OTOH, if we detect we're greater than the current time source, we atomically
replace the value with our new readings. This do causes contention on big
boxes (but big here means *BIG*), but it seems like a good trade off, since
it provide us with a time source guaranteed to be stable wrt time warps.
After this patch is applied, I don't see a single warp in time during 5 days
of execution, in any of the machines I saw them before.
Signed-off-by: Glauber Costa <glommer@redhat.com>
Acked-by: Zachary Amsden <zamsden@redhat.com>
CC: Jeremy Fitzhardinge <jeremy@goop.org>
CC: Avi Kivity <avi@redhat.com>
CC: Marcelo Tosatti <mtosatti@redhat.com>
CC: Zachary Amsden <zamsden@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch removes one padding byte and transform it into a flags
field. New versions of guests using pvclock will query these flags
upon each read.
Flags, however, will only be interpreted when the guest decides to.
It uses the pvclock_valid_flags function to signal that a specific
set of flags should be taken into consideration. Which flags are valid
are usually devised via HV negotiation.
Signed-off-by: Glauber Costa <glommer@redhat.com>
CC: Jeremy Fitzhardinge <jeremy@goop.org>
Acked-by: Zachary Amsden <zamsden@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch fixes a bug in the KVM efer-msr write path. If a
guest writes to a reserved efer bit the set_efer function
injects the #GP directly. The architecture dependent wrmsr
function does not see this, assumes success and advances the
rip. This results in a #GP in the guest with the wrong rip.
This patch fixes this by reporting efer write errors back to
the architectural wrmsr function.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch disables the possibility for a l2-guest to do a
VMMCALL directly into the host. This would happen if the
l1-hypervisor doesn't intercept VMMCALL and the l2-guest
executes this instruction.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The patch merged recently which allowed to mark an exception
as reinjected has a bug as it always marks the exception as
reinjected. This breaks nested-svm shadow-on-shadow
implementation.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Wallclock writing uses an unprotected global variable to hold the version;
this can cause one guest to interfere with another if both write their
wallclock at the same time.
Acked-by: Glauber Costa <glommer@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
On svm, kvm_read_pdptr() may require reading guest memory, which can sleep.
Push the spinlock into mmu_alloc_roots(), and only take it after we've read
the pdptr.
Tested-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Per document, for feature control MSR:
Bit 1 enables VMXON in SMX operation. If the bit is clear, execution
of VMXON in SMX operation causes a general-protection exception.
Bit 2 enables VMXON outside SMX operation. If the bit is clear, execution
of VMXON outside SMX operation causes a general-protection exception.
This patch is to enable this kind of check with SMX for VMXON in KVM.
Signed-off-by: Shane Wang <shane.wang@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The recent changes to emulate string instructions without entering guest
mode exposed a bug where pending interrupts are not properly reflected
in ready_for_interrupt_injection.
The result is that userspace overwrites a previously queued interrupt,
when irqchip's are emulated in userspace.
Fix by always updating state before returning to userspace.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
When EPT is enabled, we cannot emulate EFER.NX=0 through the shadow page
tables. This causes accesses through ptes with bit 63 set to succeed instead
of failing a reserved bit check.
Signed-off-by: Avi Kivity <avi@redhat.com>
Some guest msr values cannot be used on the host (for example. EFER.NX=0),
so we need to switch them atomically during guest entry or exit.
Add a facility to program the vmx msr autoload registers accordingly.
Signed-off-by: Avi Kivity <avi@redhat.com>
vmx and svm vcpus have different contents and therefore may have different
alignmment requirements. Let each specify its required alignment.
Signed-off-by: Avi Kivity <avi@redhat.com>
Move unsync/sync tracepoints to the proper place, it's good
for us to obtain unsync page live time
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
If the guest is 32-bit, we should use 'quadrant' to adjust gpa
offset
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
kvm_mmu_remove_one_alloc_mmu_page() assumes kvm_mmu_zap_page() only reclaims
only one sp, but that's not the case. This will cause mmu shrinker returns
a wrong number. This patch fix the counting error.
Signed-off-by: Gui Jianfeng <guijianfeng@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
For TDP mode, avoid creating multiple page table roots for the single
guest-to-host physical address map by fixing the inputs used for the
shadow page table hash in mmu_alloc_roots().
Signed-off-by: Eric Northup <digitaleric@google.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Should be there for the sake of RAW events.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
CC: Lin Ming <ming.m.lin@intel.com>
CC: Peter Zijlstra <a.p.zijlstra@chello.nl>
CC: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <20100518212439.354345151@openvz.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This snippet somehow escaped the commit:
| commit 137351e0fe
| Author: Cyrill Gorcunov <gorcunov@openvz.org>
| Date: Sat May 8 15:25:52 2010 +0400
|
| x86, perf: P4 PMU -- protect sensible procedures from preemption
so bring it eventually back. It helps to catch
preemption issue (if there will be, rule of thumb --
don't use raw_ if you can).
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Lin Ming <ming.m.lin@intel.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <20100518212439.167259349@openvz.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
To prevent from clashes in future code modifications
do a real check for ESCR address being in hash. At
moment the callers are known to pass sane values but
better to be on a safe side.
And comment fix.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
CC: Lin Ming <ming.m.lin@intel.com>
CC: Peter Zijlstra <a.p.zijlstra@chello.nl>
CC: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <20100518212439.004503600@openvz.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
WARN() is used in some places to report firmware or hardware bugs that
are then worked-around. These bugs do not affect the stability of the
kernel and should not set the flag for TAINT_WARN. To allow for this,
add WARN_TAINT() and WARN_TAINT_ONCE() macros that take a taint number
as argument.
Architectures that implement warnings using trap instructions instead
of calls to warn_slowpath_*() now implement __WARN_TAINT(taint)
instead of __WARN().
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Helge Deller <deller@gmx.de>
Tested-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Because SLOB fancies being different, the default minimum alignment is
only "unsigned long" instead of SLAB/SLUB where the default is
"unsigned long long"
The inconsistency makes no sense and is asking for trouble, but define
ARCH_SLAB_MINALIGN to get it right in all cases even after they fix
the inconsistency.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch eliminates the node pointer from struct of_device and the
of_node (or prom_node) pointer from struct dev_archdata since the node
pointer is now part of struct device proper when CONFIG_OF is set, and
all users of the old pointer locations have already been converted over
to use device->of_node.
Also remove dev_archdata_{get,set}_node() as it is no longer used by
anything.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The following structure elements duplicate the information in
'struct device.of_node' and so are being eliminated. This patch
makes all readers of these elements use device.of_node instead.
(struct of_device *)->node
(struct dev_archdata *)->prom_node (sparc)
(struct dev_archdata *)->of_node (powerpc & microblaze)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Both ACPI and SFI firmwares will have MCFG space, but the error message
isn't valid on SFI, so don't print the message in that case.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
One entry for this in arch/ia64/Kconfig should be enough.
Reported-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
As explained in commit 1c0fe6e3bd, we want to call the architecture independent
oom killer when getting an unexplained OOM from handle_mm_fault, rather than
simply killing current.
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Replace open-coded rate limiting logic with __ratelimit().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
There is a macro called dev_info that prints struct device specific
information. Having variables with the same name can be confusing and
prevents conversion of the macro to a function.
Rename the existing dev_info variables to something else in preparation
to converting the dev_info macro to a function.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Pointless to use #ifdef CONFIG_NUMA in code that is
already inside another #ifdef CONFIG_NUMA.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Convert to the transactional PMU API and remove the duplication of
group_sched_in().
[cross build only]
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Acked-by: David Miller <davem@davemloft.net>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1272002193.5707.65.camel@minggr.sh.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-pat-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, pat: Update the page flags for memtype atomically instead of using memtype_lock
x86, pat: In rbt_memtype_check_insert(), update new->type only if valid
x86, pat: Migrate to rbtree only backend for pat memtype management
x86, pat: Preparatory changes in pat.c for bigger rbtree change
rbtree: Add support for augmented rbtrees
* 'core-hweight-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, hweight: Use a 32-bit popcnt for __arch_hweight32()
arch, hweight: Fix compilation errors
x86: Add optimized popcnt variants
bitops: Optimize hweight() by making use of compile-time evaluation
* 'x86-irq-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, acpi/irq: Define gsi_end when X86_IO_APIC is undefined
x86, irq: Kill io_apic_renumber_irq
x86, acpi/irq: Handle isa irqs that are not identity mapped to gsi's.
x86, ioapic: Simplify probe_nr_irqs_gsi.
x86, ioapic: Optimize pin_2_irq
x86, ioapic: Move nr_ioapic_registers calculation to mp_register_ioapic.
x86, ioapic: In mpparse use mp_register_ioapic
x86, ioapic: Teach mp_register_ioapic to compute a global gsi_end
x86, ioapic: Fix the types of gsi values
x86, ioapic: Fix io_apic_redir_entries to return the number of entries.
x86, ioapic: Only export mp_find_ioapic and mp_find_ioapic_pin in io_apic.h
x86, acpi/irq: Generalize mp_config_acpi_legacy_irqs
x86, acpi/irq: Fix acpi_sci_ioapic_setup so it has both bus_irq and gsi
x86, acpi/irq: pci device dev->irq is an isa irq not a gsi
x86, acpi/irq: Teach acpi_get_override_irq to take a gsi not an isa_irq
x86, acpi/irq: Introduce apci_isa_irq_to_gsi
* 'x86-fpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, fpu: Use static_cpu_has() to implement use_xsave()
x86: Add new static_cpu_has() function using alternatives
x86, fpu: Use the proper asm constraint in use_xsave()
x86, fpu: Unbreak FPU emulation
x86: Introduce 'struct fpu' and related API
x86: Eliminate TS_XSAVE
x86-32: Don't set ignore_fpu_irq in simd exception
x86: Merge kernel_math_error() into math_error()
x86: Merge simd_math_error() into math_error()
x86-32: Rework cache flush denied handler
Fix trivial conflict in arch/x86/kernel/process.c
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, hypervisor: add missing <linux/module.h>
Modify the VMware balloon driver for the new x86_hyper API
x86, hypervisor: Export the x86_hyper* symbols
x86: Clean up the hypervisor layer
x86, HyperV: fix up the license to mshyperv.c
x86: Detect running on a Microsoft HyperV system
x86, cpu: Make APERF/MPERF a normal table-driven flag
x86, k8: Fix build error when K8_NB is disabled
x86, cacheinfo: Disable index in all four subcaches
x86, cacheinfo: Make L3 cache info per node
x86, cacheinfo: Reorganize AMD L3 cache structure
x86, cacheinfo: Turn off L3 cache index disable feature in virtualized environments
x86, cacheinfo: Unify AMD L3 cache index disable checking
cpufreq: Unify sysfs attribute definition macros
powernow-k8: Fix frequency reporting
x86, cpufreq: Add APERF/MPERF support for AMD processors
x86: Unify APERF/MPERF support
powernow-k8: Add core performance boost support
x86, cpu: Add AMD core boosting feature flag to /proc/cpuinfo
Fix up trivial conflicts in arch/x86/kernel/cpu/intel_cacheinfo.c and
drivers/cpufreq/cpufreq_ondemand.c
* 'x86-atomic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix LOCK_PREFIX_HERE for uniprocessor build
x86, atomic64: In selftest, distinguish x86-64 from 586+
x86-32: Fix atomic64_inc_not_zero return value convention
lib: Fix atomic64_inc_not_zero test
lib: Fix atomic64_add_unless return value convention
x86-32: Fix atomic64_add_unless return value convention
lib: Fix atomic64_add_unless test
x86: Implement atomic[64]_dec_if_positive()
lib: Only test atomic64_dec_if_positive on archs having it
x86-32: Rewrite 32-bit atomic64 functions in assembly
lib: Add self-test for atomic64_t
x86-32: Allow UP/SMP lock replacement in cmpxchg64
x86: Add support for lock prefix in alternatives
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Use .cfi_sections for assembly code
x86-64: Reduce SMP locks table size
x86, asm: Introduce and use percpu_inc()
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (49 commits)
stop_machine: Move local variable closer to the usage site in cpu_stop_cpu_callback()
sched, wait: Use wrapper functions
sched: Remove a stale comment
ondemand: Make the iowait-is-busy time a sysfs tunable
ondemand: Solve a big performance issue by counting IOWAIT time as busy
sched: Intoduce get_cpu_iowait_time_us()
sched: Eliminate the ts->idle_lastupdate field
sched: Fold updating of the last_update_time_info into update_ts_time_stats()
sched: Update the idle statistics in get_cpu_idle_time_us()
sched: Introduce a function to update the idle statistics
sched: Add a comment to get_cpu_idle_time_us()
cpu_stop: add dummy implementation for UP
sched: Remove rq argument to the tracepoints
rcu: need barrier() in UP synchronize_sched_expedited()
sched: correctly place paranioa memory barriers in synchronize_sched_expedited()
sched: kill paranoia check in synchronize_sched_expedited()
sched: replace migration_thread with cpu_stop
stop_machine: reimplement using cpu_stop
cpu_stop: implement stop_cpu[s]()
sched: Fix select_idle_sibling() logic in select_task_rq_fair()
...
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (311 commits)
perf tools: Add mode to build without newt support
perf symbols: symbol inconsistency message should be done only at verbose=1
perf tui: Add explicit -lslang option
perf options: Type check all the remaining OPT_ variants
perf options: Type check OPT_BOOLEAN and fix the offenders
perf options: Check v type in OPT_U?INTEGER
perf options: Introduce OPT_UINTEGER
perf tui: Add workaround for slang < 2.1.4
perf record: Fix bug mismatch with -c option definition
perf options: Introduce OPT_U64
perf tui: Add help window to show key associations
perf tui: Make <- exit menus too
perf newt: Add single key shortcuts for zoom into DSO and threads
perf newt: Exit browser unconditionally when CTRL+C, q or Q is pressed
perf newt: Fix the 'A'/'a' shortcut for annotate
perf newt: Make <- exit the ui_browser
x86, perf: P4 PMU - fix counters management logic
perf newt: Make <- zoom out filters
perf report: Report number of events, not samples
perf hist: Clarify events_stats fields usage
...
Fix up trivial conflicts in kernel/fork.c and tools/perf/builtin-record.c
* 'oprofile-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (24 commits)
oprofile/x86: make AMD IBS hotplug capable
oprofile/x86: notify cpus only when daemon is running
oprofile/x86: reordering some functions
oprofile/x86: stop disabled counters in nmi handler
oprofile/x86: protect cpu hotplug sections
oprofile/x86: remove CONFIG_SMP macros
oprofile/x86: fix uninitialized counter usage during cpu hotplug
oprofile/x86: remove duplicate IBS capability check
oprofile/x86: move IBS code
oprofile/x86: return -EBUSY if counters are already reserved
oprofile/x86: moving shutdown functions
oprofile/x86: reserve counter msrs pairwise
oprofile/x86: rework error handler in nmi_setup()
oprofile: update file list in MAINTAINERS file
oprofile: protect from not being in an IRQ context
oprofile: remove double ring buffering
ring-buffer: Add lost event count to end of sub buffer
tracing: Show the lost events in the trace_pipe output
ring-buffer: Add place holder recording of dropped events
tracing: Fix compile error in module tracepoints when MODULE_UNLOAD not set
...
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
lockdep: Reduce stack_trace usage
lockdep: No need to disable preemption in debug atomic ops
lockdep: Actually _dec_ in debug_atomic_dec
lockdep: Provide off case for redundant_hardirqs_on increment
lockdep: Simplify debug atomic ops
lockdep: Fix redundant_hardirqs_on incremented with irqs enabled
lockstat: Make lockstat counting per cpu
i8253: Convert i8253_lock to raw_spinlock
* 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/amd-iommu: Add amd_iommu=off command line option
iommu-api: Remove iommu_{un}map_range functions
x86/amd-iommu: Implement ->{un}map callbacks for iommu-api
x86/amd-iommu: Make amd_iommu_iova_to_phys aware of multiple page sizes
x86/amd-iommu: Make iommu_unmap_page and fetch_pte aware of page sizes
x86/amd-iommu: Make iommu_map_page and alloc_pte aware of page sizes
kvm: Change kvm_iommu_map_pages to map large pages
VT-d: Change {un}map_range functions to implement {un}map interface
iommu-api: Add ->{un}map callbacks to iommu_ops
iommu-api: Add iommu_map and iommu_unmap functions
iommu-api: Rename ->{un}map function pointers to ->{un}map_range
This patch adds DSS2 support to the beagleboard boardfile. DVI and
TV-out are supported.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Add LCD, Boot-up logo, framebuffer console, Keypad
and Power button support
Signed-off-by: Roger Quadros <roger.quadros@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
The Touch controller and LCD Panel share the same SPI bus 1.
So, we need to define the touch controller in the SPI board info
else, the SPI bus will be contended due to invalid state of
Touch controller's Chip Select thus preventing the LCD panel
from working.
Signed-off-by: Roger Quadros <roger.quadros@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Adds basic support for LCD Panel on Nokia N900
Signed-off-by: Roger Quadros <roger.quadros@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Define platform devices for all audio devices found on S5P6440
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Define platform devices for all audio devices found on S5P6442
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Define platform devices for all audio devices found on S5PV210
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The pm-gpio.c code was incrementing the gpio_nr from the nr_gpios
field and the bank-bank offset inside the loop, and also in the
for() loop with a ++.
Remove the ++, as the number is already at the next GPIO, thus
ensuring that we don't skip a gpio bank by accident.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
As part of the cleanup, remove the old macros mapping GPIO numbers
to the base of the register now we have gpiolib to manage the GPIO
mappings for us.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Update a couple of S3C24XX and S3C2412 files that are still
using the GPIO number to register mapping calls to get the
s3c_gpio_chip and use the base field from that.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Start cleaning up the numbering of GPIO banks by removing the old
bank start definitions currently being used by some of the header
files.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Increase GPIOs number for S3C244X, and make S3C_GPIO_END
point to BANKJ end, otherwise gpiolib refuses to register
BANKJ
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
[ben-linux@fluff.org: Move pm fix to new patch]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the S3C_FB_MAX_WIN to the platform data to avoid
having to include the registers with the platform data.
Set S3C_FB_MAX_WIN to 5, which is the maximum that any
of the current hardware can do and the cost of having
it set to this for all is minimal (at least for the
platform data case), then always leave this as the maximum
for the systems supported.
Also remove the inclusion of <mach/regs-fb.h> from
the device definition in arch/arm/plat-samsung
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the definition of the LCD clock bit, it is the TFT display
controller on bit 9, not the older STN on bit 10.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This adds the xusbxti clock to S3C64XX platform.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Now that the node 0 initialization code has been overhauled, kill off the
now obsolete setup_memory() bits.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Samsung's Soc S5PV210 has three PL330 DMACs. First is dedicated for
Memory->Memory data transfer while the other two meant for data
transfer with peripherals.
Define and add latter two PL330 DMACs as platform devices on the
S5PV210 platform.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Samsung's Soc S5P6442 has two PL330 DMACs. First is dedicated for
Memory->Memory data transfer while the second is meant for data
transfer with peripherals.
Define and add the peripheral PL330 DMAC as platform device on the
S5P6442 platform.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Samsung's Soc S5P6440 has one PL330 DMAC.
Define and add the PL330 DMAC as platform device on the
S5P6440 platform.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Latest Samsung SoCs have one or more PL330 as their DMACs. This patch
implements the S3C DMA API for PL330 core driver.
The design has been kept as generic as possible while keeping effort to
add support for new SoCs to the minimum possible level.
Some of the salient features of this driver are:-
o Automatic scheduling of client requests onto DMAC if more than
one DMAC can reach the peripheral. Factors, such as current load
and number of exclusive but inactive peripherals that are
supported by the DMAC, are used to decide suitability of a DMAC
for a particular client.
o CIRCULAR buffer option is supported.
o The driver scales transparently with the number of DMACs and total
peripherals in the platform, since all peripherals are added to
the peripheral pool and DMACs to the controller pool.
For most conservative use of memory, smallest driver size and best
performance, we don't employ legacy data structures of the S3C DMA API.
That should not have any affect since those data structures are completely
invisible to the DMA clients.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch de-asserts the reset line that is connected to the USB
ULPI PHY on USB Host1.
This patch should be included with the original USB host enablement
set of patches of mx51 babbage hw, but was accidentily left out.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch moves RTC device definitions from mach-s3c64xx
to plat-samsung, to enable the other SoCs to use same device
definition.
Signed-off-by: Atul Dahiya <atul.dahiya@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Andrea Gelmini
Huang Weiyi
Sebastian Andrzej Siewior
Linus Torvalds
Philippe De Muyter
Greg Ungerer
Paul Mundt
Ben Dooks
Jassi Brar
Pinkava J
Russell King
Akinobu Mita
Joe Perches
Wolfram Sang
Michael Hennerich
Mike Frysinger
FUJITA Tomonori
Robin Getz
Graf Yang
Frederic Weisbecker
Guennadi Liakhovetski
Grant Likely
Al Viro
Ira W. Snyder
David Daney
Florian Fainelli
Wu Zhangjin
Kevin Cernekee
David VomLehn
Shane McDonald
Arnaud Patard
Manuel Lauss
Julia Lawall
Chris Wright
Cliff Cai
Andy Fleming
Anton Vorontsov
Scott Wood
Michael Neuling
Mark Nelson
Anton Blanchard
Maxim Uvarov
Sonny Rao
Brian King
Paul Mackerras
Milton Miller
Andreas Schwab
Michael Ellerman
Jason Wessel
Jan Kiszka
Santosh Shilimkar
Magnus Damm
Srinidhi Kasagar
Anand Gadiyar
Ajay Kumar Gupta
Tony Lindgren
Paul Walmsley
Rajendra Nayak
Laine Walker-Avina
Benoit Cousson
Felipe Balbi
Jason Lam
kishore kadiyala
Balaji T K
stanley.miao
Charulatha V
Abraham Arce
manjugk manjugk
Mika Westerberg
Roger Quadros
Janusz Krzysztofik
Jarkko Nikula
Steve Sakoman
Sriram
Thomas Weber
Viral Mehta
Ingo Molnar
Banajit Goswami
Maurus Cuelenaere
Takashi Iwai
Joonyoung Shim
Marek Szyprowski
Jongpill Lee
Naveen Krishna Ch
Huang Ying
Kalle Jokiniemi
Alberto Panizzo
Thomas Abraham
Pannaga Bhushan
Avi Kivity
Sheng Yang
Glauber Costa
Roedel, Joerg
Shane Wang
Marcelo Tosatti
Xiao Guangrong
Stephen Rothwell
Gui Jianfeng
Eric Northup
Cyrill Gorcunov
Ben Hutchings
David S. Miller
Feng Tang
Tony Luck
npiggin@suse.de
Jiri Olsa
Lin Ming
Koen Kooi
Vaibhav Hiremath
Vasily Khoruzhick
Dinh Nguyen
Atul Dahiya