Add frame buffer compression on Sandybridge. The method is similar to
Ironlake, except that two new registers of type GTTMMADR must be written
with the right fence info.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Add the support of memory self-refresh on Sandybridge, which is now
support 3 levels of watermarks and the source of the latency values
for watermarks has changed.
On Sandybridge, the LP0 WM value is not hardcoded any more. All the
latency value is now should be extracted from MCHBAR SSKPD register.
And the MCHBAR base address is changed, too.
For the WM values, if any calculated watermark values is larger than
the maximum value that can be programmed into the associated watermark
register, that watermark must be disabled.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
[ickle: remove duplicate compute routines and fixup for checkpatch]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Be paranoid and ensure that the vblank has passed and the scanout has
switched to the new fb, before unpinning the old one and possibly
tearing down its PTEs.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Restore PIPE_CONTROL once again just for Ironlake, as it appears that
MI_USER_INTERRUPT does not have the same coherency guarantees, that is
on Ironlake the interrupt following a GPU write is not guaranteed to
arrive after the write is coherent from the CPU, as it does on the
other generations.
Reported-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Reported-by: Shuang He <shuang.he@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=32402
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Fixes the lack of output on the LVDS panel of the Lenovo U160.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=31596
Reported-and-tested-by: Dirk Gouders <gouders@et.bocholt.fh-gelsenkirchen.de>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
As we already know the limits for the hardware clock, pass it down
rather than recomputing them for each match.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
In order to enforce the correct memory barriers for irq get/put, we need
to perform the actual counting using atomic operations.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
BIOSes. Can't live without them (apparently), definitely can't live with
them.
Reported-by: Ben Gamari <bgamari@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=24312
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Once we have read the value out of the GT power well, we need to remove
the FORCE WAKE bit to allow the system to auto-power down.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
As suggested by Daniel Vetter, this is a safeguard should any of the
registers cause reference to PTE entries.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
As we provide a list of all objects that will be accessed from the
batchbuffer, we can build a lut of the handles associated with those
objects for this invocation and use that to avoid the overhead of
looking up those objects again for every relocation.
The cost of building and searching a small hash table is much less than
that of acquiring a spinlock, searching a radix tree and manipulating an
atomic refcnt per relocation.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Don't post a downclocking task if the device is still active when the
idle timer fires. A pathological process could queue up several seconds
worth of processing and then go to sleep, during which time the idle
timer would kick in and downclock the GPU.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If the tail advances beyond the autoreport HEAD value, then we need to
fallback to an uncached read of the HEAD register in order to ascertain
the correct amount of remaining space in the ringbuffer.
Reported-by: Fang, Xun <xunx.fang@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=32259
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The DisplayPort standard (1.1a) states that:
The I2C-over-AUX Reply field is valid only when Native AUX CH Reply
field is AUX_ACK (00). When Native AUX CH Reply field is not 00, then,
I2C-over-AUX Reply field must be 00 and be ignored.
This fixes broken EDID reading when using an active DisplayPort to
duallink DVI converter. If the AUX CH replier chooses to defer the
transaction, a short read occurs and erroneous data is returned as
the i2c reply due to a lack of length checking and failure to check
for AUX ACK.
As a result, broken EDIDs can look like:
0 1 2 3 4 5 6 7 8 9 a b c d e f 0123456789abcdef
00: bc bc bc ff bc bc bc ff bc bc bc ac bc bc bc 45 ???.???.???????E
10: bc bc bc 10 bc bc bc 34 bc bc bc ee bc bc bc 4c ???????4???????L
20: bc bc bc 50 bc bc bc 00 bc bc bc 40 bc bc bc 00 ???P???.???@???.
30: bc bc bc 01 bc bc bc 01 bc bc bc a0 bc bc bc 40 ???????????????@
40: bc bc bc 00 bc bc bc 00 bc bc bc 00 bc bc bc 55 ???.???.???.???U
50: bc bc bc 35 bc bc bc 31 bc bc bc 20 bc bc bc fc ???5???1??? ????
60: bc bc bc 4c bc bc bc 34 bc bc bc 46 bc bc bc 00 ???L???4???F???.
70: bc bc bc 38 bc bc bc 11 bc bc bc 20 bc bc bc 20 ???8??????? ???
80: bc bc bc ff bc bc bc ff bc bc bc ff bc bc bc ff ???.???.???.???.
...
which can lead to:
[drm:drm_edid_block_valid] *ERROR* EDID checksum is invalid, remainder
[drm:drm_edid_block_valid] *ERROR* Raw EDID:
<3>30 30 30 30 30 30 30 32 38 32 30 32 63 63 31 61 000000028202cc1a
<3>28 00 02 8c 00 00 00 00 18 00 00 00 00 00 00 00 (...............
<3>20 4c 61 73 74 20 62 65 61 63 6f 6e 3a 20 33 32 Last beacon: 32
<3>32 30 6d 73 20 61 67 6f 46 00 05 8c 00 00 00 00 20ms agoF.......
<3>36 00 00 00 00 00 00 00 00 0c 57 69 2d 46 69 20 6.........Wi-Fi
<3>52 6f 75 74 65 72 01 08 82 84 8b 96 24 30 48 6c Router......$0Hl
<3>03 01 01 06 02 00 00 2a 01 00 2f 01 00 32 04 0c .......*../..2..
<3>12 18 60 dd 09 00 10 18 02 00 00 01 00 00 18 00 ..`.............
Signed-off-by: David Flynn <davidf@rd.bbc.co.uk>
[ickle: fix up some surrounding checkpatch warnings]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
As we may try to power down the link at various times, it is not
necessarily still coupled with an encoder and so we must be careful not
to depend upon an operation that is only valid when the link is still
attached to a pipe.
Fixes regression in 5bddd17.
Reported-and-tested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org [after applying 5bddd17]
In order for bos to retire eventually, a request must be sent down the
ring. This is expected, for example, by occlusion queries for which mesa
will wait upon (whilst running glean) before issuing more batches and so
the normal activity upon the ring is suspended and we need to emit a
request to clear the idle ring.
Reported-by: Jinjin, Wang <jinjin.wang@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30380
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
I'm still seeing tiling corruption of PutImage and CopyArea (I think)
under mutter on pnv, so obviously the pipelining logic is deeply flawed.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Userspace should not have been declaring that it needed fenced GPU
access with gen4+ as those GPUs have no fenced commands, but to be on
the safe side it is easier to ignore userspace in case they did.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The ability to save the hardware context upon powering down the render
clock through PWRCTXA is only available on a couple of gen4 chipsets.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The workaround is hideous and we are using the STORE_DWORD on all other
generations on all other rings, so use for the gen5 render ring as
well.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Linus Torvalds pointed out that our code was unbalanced when powering on
the panel with respect to the power off sequence in that we were failing
to restore the panel-fitter. The consequence of this would be that
across a simple DPMS off/on for a non-native mode, without an intervening
modeset, the panel fitter would remain disabled and the output would shift
on the panel.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
There's not much we can do here but hope for the best. However the first
failure happens quite frequently and if often remedied by the second
attempt to reset HEAD. So only print the error if that attempt also
fails.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=19802
Reported-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Otherwise we can't really fix the abi-braindeadness of forcing
libva to manually wait for rendering when switching rings. Which
in turn makes implementing hw semaphores a pointless exercise
(at least for ironlake).
[Also added the relaxed fencing param to explain the jump in
numbering - relaxed fencing is in -next.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The bulk of the change is to convert the growing list of rings into an
array so that the relationship between the rings and the semaphore sync
registers can be easily computed.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Previously we enabled this for gen4, only to have to revert it due to it
causing a large number of spurious wakeups. Try again hoping that the
hardware has become more sane in the mean time...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Magic numbers from the specs. This is supposed to allow the PLL some
variance to improve jitter performance and VCO headroom across
manufacturing and environmental variations.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
... it's because setting the Pixel Multiply bits only takes effect once
the PLL is enabled and stable.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Fixes the modesetting on the secondary panel of the Libretto W100 and
presumably many more Ironlake laptops with SDVO LVDS displays.
Reported-and-tested-by: Matthew Willoughby <mattfredwill@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Use the hardware DDA to calculate the ratio with as much accuracy as is
possible.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
If we leave the registers in a conflicting state then when we attempt
to teardown the active mode, we will not disable the pipes and planes
in the correct order -- leaving a plane reading from a disabled pipe and
possibly leading to undefined behaviour.
Reported-and-tested-by: Andy Whitcroft <apw@canonical.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=32078
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
This workaround only applies to Ironlake.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
The pipe is always set to 8BPC, but here we were leaving whatever
previous bits were set by the BIOS in place.
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
As the tracepoint is now decoupled from when the actual register is
assigned and was never complemented by detailing when the object lost
its fence, it has outlived its limited usefulness. Profiling the actual
stalls is a far more profitable venture anyway.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
As the userspace mappings are torn down on every GPU write, we prefer to
track when the buffer is activated (via a fresh i915_gem_fault). This
makes the LRU conceptually simpler. With coherent mappings, the
remaining use-case for set_domain_ioctl is GPU synchronisation.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
With this change, every batchbuffer can use all available fences (save
pinned and scanout, of course) without ever stalling the gpu!
In theory. Currently the actual pipelined update of the register is
disabled due to some stability issues. However, just the deferred update
is a significant win.
Based on a series of patches by Daniel Vetter.
The premise is that before every access to a buffer through the GTT we
have to declare whether we need a register or not. If the access is by
the GPU, a pipelined update to the register is made via the ringbuffer,
and we track the last seqno of the batches that access it. If by the
CPU we wait for the last GPU access and update the register (either
to clear or to set it for the current buffer).
One advantage of being able to pipeline changes is that we can defer the
actual updating of the fence register until we first need to access the
object through the GTT, i.e. we can eliminate the stall on set_tiling.
This is important as the userspace bo cache does not track the tiling
status of active buffers which generate frequent stalls on gen3 when
enabling tiling for an already bound buffer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This makes the various rings more consistent by removing the anomalous
handing of the rendering ring execbuffer dispatch.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This reverts commit 869184a675.
This is required for the Sony Vaio Jesse was working on at the time, but
breaks most other eDP machines - machines that were working in earlier
kernels.
Reported-and-tested-by: Dave Airlie <airlied@redhat.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=31188
Tested-by: Zhao Jian <jian.j.zhao@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
... otherwise the panel-fitter may be left enabled with random settings
and cause unintended filtering (i.e. blurring of native modes on external
panels).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=31942
Reported-and-tested-by: Ben Kohler <bkohler@gmail.com>
Tested-by: Ciprian Docan <docan@eden.rutgers.edu>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
... so that upon first use after resume we will reacquire the fence reg.
Reported-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
As the error occurred on the current object, it means that its state was
not changed and so it should be excluded from the unwind.
Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We don't track gpu flush request in any special way. So even with
obj->write_domain == 0, a gpu flush might be outstanding but no
yet executed. Even worse, the latest request might use the object
only for reading. So and unconditional call to object_wait_rendering
is needed for !pipelined.
Hence revert that patch fully and untangle the flushing from the
synchronization again.
Reported-by: Keith Packard <keithp@keithp.com>
Tested-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Besides the minimal improvement in reducing the execbuffer overhead, the
real benefit is clarifying a few routines.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
A number of dragons have been seen lurking within the execbuffer code.
The first step is then to isolate them from the rest and begin to
scrutinise them in depth. Suggested by Daniel Vetter.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Simply remove our accounting of objects inside the aperture, keeping
only track of what is in the aperture and its current usage. This
removes the over-complication of BUGs that were attempting to keep the
accounting correct and also removes the overhead of the accounting on
the hot-paths.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
With KMS, we can simply relinquish the fence when we idle the GPU and
reassign it upon first use.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Commit d09c23de intended to add a 30ms delay to give the ADD time to
detect any TVs connected. However, it used the sdvo->is_tv flag to do so
which is dependent upon the previous detection result and not whether the
output supports TVs.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Avoid evicting buffers that will be used later in the batch in order to
make room for the initial buffers by pinning all bound buffers in a
single pass before binding (and evicting for) fresh buffer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
On a few devices, like the Mac Mini, the CRT DDC pins are shared between
the analog connector and the digital connector. In this scenario, rely
on the EDID to determine if a digital panel is connected to the digital
connector.
Reported-and-tested-by: Tino Keitel <tino.keitel@tikei.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This used to check the precondition that all fences were to be located
in a mappable area, redundant now as those two parameters are combined
into one.
After pinning, we assert that the buffer is bound into the desired
region.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The pipe control object is allocated by the device for the sole use of the
render ringbuffer. Move this detail from the general code to the render
ring buffer initialisation.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Having seen the effects of erroneous fencing on the batchbuffer, a
useful sanity check is to record the fence registers at the time of an
error.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Combining map_and_fenceable revealed a bug in
i915_gem_object_gtt_size() in that it always computed the appropriate
fence size for the object regardless of tiling state which caused us to
over-allocate linear buffers when binding to the GTT.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This still uses the agp functions to actually reinstate the mappings
(with a gross hack to make agp cooperate), but it wires everything
up correctly for the switchover.
The call to agp_rebind_memory can be dropped because all non-kms drivers
do all their rebinding on EnterVT.
v2: Be more paranoid and flush the chipset cache after restoring gtt
mappings.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This is required to restore gtt mappings on resume when agp is gone.
The right way to do this would be to make sturct drm_mm_node embeddable
and use the allocation list maintained by the drm memory manager. But
that's a bigger project. Getting rid of the per bo agp_mem will save
more memory than this wastes, anyway.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Currently if we hit a pagefault when applying a user relocation for the
execbuffer, we bail and return EFAULT to the application. Instead, we
need to unwind, drop the dev->struct_mutex, copy all the relocation
entries to a vmalloc array (to avoid any potential circular deadlocks
when resolving the pagefault), retake the mutex and then apply the
relocations. Afterwards, we need to again drop the lock and copy the
vmalloc array back to userspace.
v2: Incorporate feedback from Daniel Vetter.
Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The GATT is a write-only set of registers, reading from them in the
manner of i915_gtt_to_phys() is supposed to be undefined. However a
simple solution exists as we allocate linear memory from the stolen
area, we can simply add the block offset to the base register. As a
side-effect we recover all the unused stolen GTT entries and so enlarge
our aperture.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
After a GPU reset, the backlight controller registers may be also reset
to 0. In that case we should restore those to the original values
programmed by the BIOS. Note that we still lack the code to handle the
case where the BIOS failed to program those registers at all...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
As we conflated intel_sdvo->is_hdmi with both having HDMI support on the
ADD along with having HDMI support on the monitor, we would attempt to
use HDMI encodings even if the interface did not support those commands.
Reported-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Reviewed-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
We were reading our 64-bit value in I915_READ64 and returning 32 bits
of it. The restoration of fence regs at resume then had a zero end
value, and the fence had no effect.
Version 2: Split register access functions into per-size versions
Sharing code between different sizes seemed reasonable when we only
needed a single copy, but as 64-bit access requires its own version,
it makes sense to just split them out for each size.
Reported-by: Peter Clifton <pcjc2@cam.ac.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
[ickle: use a macro to create the various read/write routines]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This has proven sufficient to recover from a hang of the GPU using the
gem_bad_blit test while at the KMS console then starting X. When
attempting the same during an X session, the timer doesn't appear to
trigger.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
It isn't used for the hangcheck, which does its work right from the
timer trigger, but hangcheck can lead to error state recording, which
is run off of the workqueue.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
When trying to diagnose mysterious errors on resume, capture the
display register contents as well.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The pinned buffers are useful for diagnosing errors in setting up state
for the chipset, which may not necessarily be 'active' at the time of
the error, e.g. the cursor buffer object.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Under KMS, restoring the cursor is handled upon modeswitch in order to
avoid enabling an undefined set of registers. At the moment, the cursor
is restored before the aperture and modes are fully setup causing some
invalid access during resume, such as:
PGTBL_ER: 0x00040000
Invalid GTT entry during Cursor Fetch
Fix this by only performing cursor register save/restore under UMS where
it is done in the correct sequence.
Reported-by: Arkadiusz Miskiewicz <arekm@maven.pl>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Commit 2549d6c2 removed the vmalloc used for temporary storage of the
relocation lists used during execbuffer. However, our use of vmalloc was
being protected by an integer overflow check which we do want to
preserve!
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Frame buffer compression is broken on Ironlake due to buggy hardware.
Currently it is disabled through chicken bits, but it still consumes
over 1W more than if we simply never attempt to enable the FBC code
paths.
Signed-off-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Both IBX and CPT have an automatic hotplug detection mode which appears to work reliably enough
that we can dispense with the manual force hotplug trigger stuff. This means that
hotplug detection is as simple as reading the current hotplug register values.
The first time the hotplug detection is activated, the code synchronously waits for a hotplug
sequence in case the hardware hasn't bothered to do a detection cycle since being initialized.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We will use this structure in future patches to store CRT specific
information on the encoder.
Split out and tweaked from a patch by Keith Packard.
Signed-off-by: Keith Packard <keithp@kithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Linus Torvalds found that it was rather trivial to trigger a system
freeze:
In fact, with lockdep, I don't even need to do the sysrq-d thing: it
shows the bug as it happens. It's the X server taking the same lock
recursively.
Here's the problem:
=============================================
[ INFO: possible recursive locking detected ]
2.6.37-rc2-00012-gbdbd01a #7
---------------------------------------------
Xorg/2816 is trying to acquire lock:
(&dev->struct_mutex){+.+.+.}, at: [<ffffffff812c626c>] i915_gem_fault+0x50/0x17e
but task is already holding lock:
(&dev->struct_mutex){+.+.+.}, at: [<ffffffff812c403b>] i915_mutex_lock_interruptible+0x28/0x4a
other info that might help us debug this:
2 locks held by Xorg/2816:
#0: (&dev->struct_mutex){+.+.+.}, at: [<ffffffff812c403b>] i915_mutex_lock_interruptible+0x28/0x4a
#1: (&mm->mmap_sem){++++++}, at: [<ffffffff81022d4f>] page_fault+0x156/0x37b
This recursion was introduced by rearranging the locking to avoid the
double locking on the fast path (4f27b5d and fbd5a26d) and the
introduction of the prefault to encourage the fast paths (b5e4f2b). In
order to undo the problem, we rearrange the code to perform the access
validation upfront, attempt to prefault and then fight for control of the
mutex. the best case scenario where the mutex is uncontended the
prefaulting is not wasted.
Reported-and-tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
As we may bind an object with the correct alignment, but with an invalid
size, it may pass the current checks on whether the object may be reused
with a fence.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
g33/pineview doesn't have any alignment constrains for unfenced tiled
buffers. But older chips have. Fix this.
Problem introduced in a00b10c360.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
An old and oft reported bug, is that of the GPU hanging on a
MI_WAIT_FOR_EVENT following a mode switch. The cause is that the GPU is
waiting on a scanline counter on an inactive pipe, and so waits for a
very long time until eventually the user reboots his machine.
We can prevent this either by moving the WAIT into the kernel and
thereby incurring considerable cost on every swapbuffers, or by waiting
for the GPU to retire the last batch that accesses the framebuffer
before installing a new one. As mode switches are much rarer than swap
buffers, this looks like an easy choice.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=28964
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29252
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
We only ever used the PRB0, neglecting the secondary ring buffers, and
now with the advent of multiple engines with separate ring buffers we
need to excise the anachronisms from our code (and be explicit about
which ring we mean where). This is doubly important in light of the
FORCEWAKE required to read ring buffer registers on SandyBridge.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Before reading ring register, set FORCE_WAKE bit to prevent GT core
power down to low power state, otherwise we may read stale values.
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
[ickle: added a udelay which seemed to do the trick on my SNB]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We use i915_gem_object_get_fence_reg() to do LRU tracking of the fence
registers, so stop trying to be too clever when pinning the fb->obj.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Fix many small bugs in I2C adapter registration:
* Properly reject unsupported GPIO pin.
* Fix improper use of I2C_NAME_SIZE (which is the size of
i2c_client.name, not i2c_adapter.name.)
* Prefix adapter names with "i915" so that the user knows what the
I2C channel is connected to.
* Fix swapped characters in the string used to name the GPIO-based
adapter.
* Add missing comma in gmbus name table.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Commit 219adae1 cached the EDID found during LVDS init, but in the
process prevented the init routine from discovering the preferred
fixed-mode for the panel. This was causing us to guess the correct mode,
which sometimes is wide of the mark.
Reported-and-tested-by: Jon Masters <jonathan@jonmasters.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If modeset init failed we attempted to unload the module, before we
finished setting it up and so triggered various oopses.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
As we use POSTING_READ to flush the write to the register before
proceeding, we do not care what the return value is and similar we do
not care for the read to be recorded whilst tracing register
read/writes.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
These registers are written very frequently, are timing sensitive, and
not particularly relevant to any debugging, so remove the tracepoints
from these.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This will be used later to hide the frequently written registers
from debug traces in order to increase the signal-to-noise.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Add two tracepoints at I915_WRITE/READ for tracing down all the
register write and read.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
My Sandybridge only reports 0 for the ring buffer registers, causing it
to hang as soon as we exhaust the available ring. As a workaround, take
advantage of our huge ring buffers and use the auto-reporting mechanism
to update the status page with the HEAD location every 64 KiB.
Cherry-picked from 6aa56062ea.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=31404
Tested-by: Zhao Jian <jian.j.zhao@intel.com>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This is not known to fix any particular bugs we have, but the spec
says to do it, and the BIOS hadn't already set it up on my system.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
... and so prevent a potential circular reference:
[ INFO: possible circular locking dependency detected ]
2.6.37-rc1-uwe1+ #4
-------------------------------------------------------
Xorg/1401 is trying to acquire lock:
(&mm->mmap_sem){++++++}, at: [<c01e4ddb>] might_fault+0x4b/0xa0
but task is already holding lock:
(&dev->struct_mutex){+.+.+.}, at: [<f869c3ac>]
i915_mutex_lock_interruptible+0x3c/0x60 [i915]
which lock already depends on the new lock.
When the locking around the pwrite ioctl was simplified, I did not spot
that the phys path never took any locks and so we introduced this
potential circular reference.
Reported-by: Uwe Helm <uwe.helm@googlemail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The ring buffer registers return 0 whilst idle (for some values of idle)
on early Sandybridge hw. Persevere even when all appears hopeless...
Fortunately the head auto-reporting prevents most hangs.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=31370
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Instead of killing the process, just return no page found and reschedule
the process giving the GPU some time to (hopefully) recover.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
a00b10c360 "Only enforce fence limits inside the GTT" also
added a fenceable/mappable disdinction when binding/pinning buffers.
This only complicates the code with no pratical gain:
- In execbuffer this matters on for g33/pineview, as this is the only
chip that needs fences and has an unmappable gtt area. But fences
are only possible in the mappable part of the gtt, so need_fence
implies need_mappable. And need_mappable is only set independantly
with relocations which implies (for sane userspace) that the buffer
is untiled.
- The overlay code is only really used on i8xx, which doesn't have
unmappable gtt. And it doesn't support tiled buffers, currently.
- For all other buffers it's a bug to pass in a tiled bo.
In short, this disdinction doesn't have any practical gain.
I've also reverted mapping the overlay and context pages as possibly
unmappable. It's not worth being overtly clever here, all the big
gains from unmappable are for execbuf bos.
Also add a comment for a clever optimization that confused me
while reading the original patch by Chris Wilson.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
In a00b10c360 "Only enforce fence limits inside the GTT"
Chris Wilson implemented an optimization to only pin framebuffers
as mappable for crtc_set_base (but not for pageflips). This breaks
the abi, eg: A double buffering mesa client might leave the last
framebuffer in unmappable space on close. A subsequent glReadPix
by a frontbuffer rendering client then goes boom. My pretty anal
mappable/unmappable consistency checking detected this, see
https://bugs.freedesktop.org/show_bug.cgi?id=31286
Chris Wilson tried to fix this in 085ce26437 by pinning
tiled framebuffers into mappable space. This
a) renders the original optimization of not forcing framebuffers
for pageflipping clients into mappable pointless because all our
scanout buffers are tiled by default.
b) doesn't solve the problem for untiled framebuffers.
So kill this. Emperically it's no gain anyway because framebuffers are
being reused by the ddx and hence there's no chance for them to get
constanly bounced between mappable and unmappable.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We should enable FDI normal training on Sandybridge/CPT system
as well.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
[ickle: removed unrelated chunks]
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Fixes issue where i915_gfx_val was reporting values several
orders of magnitude higher than physically possible (without
leaving scorch marks on my thighs at least.)
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
When merging Daniel's full-gtt patches I had a set of tweaks which I
thought I had undone. I was half right...
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=31286
Reported-by: jinjin.wang@intel.com
Reported-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
I presumed that we would be writing to the batch through the GTT having
bound it, so I converted it to use iomem. Even later as I spotted that
we didn't even move the batch to the GTT (now an issue since we default
to uncached memory on SNB) I still didn't realise that using iomem for
kmapped memory was incorrect. Fix it.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Immediate merge to resolve conflicts from applying a stability fix to
both branches.
Conflicts:
drivers/gpu/drm/i915/intel_ringbuffer.c
drivers/gpu/drm/i915/intel_ringbuffer.h
On some stepping of SNB cpu, the first command to be parsed in BLT
command streamer should be MI_BATCHBUFFER_START otherwise the GPU
may hang.
(cherry picked from commit 8d19215be8)
Conflicts:
drivers/gpu/drm/i915/intel_ringbuffer.c
drivers/gpu/drm/i915/intel_ringbuffer.h
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
On some stepping of SNB cpu, the first command to be parsed in BLT
command streamer should be MI_BATCHBUFFER_START otherwise the GPU
may hang.
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
[ickle: rebased for -next]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Part of the issue here was that Eric slipped in a debug hack for
testing the i915 IPS code before the intel_ips.c driver had landed.
This caused the driver to always use the full range of frequencies,
which is only legal when IPS tells us we have the headroom. Once that
hack was removed, there was confusion about the driver's frequency
clamping variables: max_delay is the driver's current limit on the
highest frequency the IPS driver wants us to use, while dev_priv->fmax
is the hardware-reported limit that the IPS driver can increase up to.
Tested with IPS driver loaded or not. Note that on Ironlake systems
without the IPS driver loaded this will result in a performance
reduction, and the inital warmup of frequency limits can impact
benchmarking on systems with IPS loaded.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
[ickle: demoted a debugging printk]
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
2.6.36 appears to respect the 0400 mode we assigned to the parameter
preventing it from being adjusted after loading. However, this is safe
to adjust at runtime.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=31311
Reported-by: Fernando Lemos <fernandotcl@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
In case of an opregion signature mismatch in intel_opregion_setup(),
iounmap the correct address.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Take two passes to evict everything whilst searching for sufficient free
space to bind the batchbuffer. After searching for sufficient free space
using LRU eviction, evict everything that is purgeable and try again.
Only then if there is insufficient free space (or the GTT is too badly
fragmented) evict everything from the aperture and try one last time.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Accessing the uninitialised obj->pages instead of the local page lead to
an OOPs.
Reported-by: Xavier Chantry <chantry.xavier@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
My Sandybridge only reports 0 for the ring buffer registers, causing it
to hang as soon as we exhaust the available ring. As a workaround, take
advantage of our huge ring buffers and use the auto-reporting mechanism
to update the status page with the HEAD location every 64 KiB.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
After switching the MMIO registers to use pci_iomap, remember to dispose
of the mapping with pci_iounmap (for symmetry).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
So long as we adhere to the fence registers rules for alignment and no
overlaps (including with unfenced accesses to linear memory) and account
for the tiled access in our size allocation, we do not have to allocate
the full fenced region for the object. This allows us to fight the bloat
tiling imposed on pre-i965 chipsets and frees up RAM for real use. [Inside
the GTT we still suffer the additional alignment constraints, so it doesn't
magic allow us to render larger scenes without stalls -- we need the
expanded GTT and fence pipelining to overcome those...]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Also spotted by Dan Carpenter.
obj->pin_count is unsigned so the BUG_ON(obj->pin_count<0) will never
trigger.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The error code is only expected during the actual pruning and not during
the first measurement (nr_to_scan == 0) pass.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
It is possible for the active list to only contain a read-only buffer so
that the ring->gpu_write_list remains entry. This leads to an
inconsistency between i915_gpu_is_active() and i915_gpu_idle() causing
an infinite spin during the shrinker and an assertion failure that
i915_gpu_idle() does indeed flush all buffers from the active lists.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
In order to force a page-fault on a GTT mapping after we start using it
from the GPU and so enforce correct CPU/GPU synchronisation, we need to
invalidate the mapping.
Pointed out by Owain G. Ainsworth.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
By using read_cache_page() for individual pages during pwrite/pread we
can eliminate an unnecessary large allocation (and immediate free) of
obj->pages. Also this eliminates any potential nesting of get/put pages,
simplifying the code and preparing the path for greater things.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Since we rarely use the mmap_offset and it is easily computable from the
obj->map_list.hash, remove it.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Eliminate the racy device unload by embedding a shrinker into each
device. Smaller, simpler code.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Play safe and use the common routines which take care of the cachability
of the memory when setting up the iomapping for the PCI registers.
Whilst they should be cacheable for the current generations, actually
honouring what the device requires is a better long term strategy.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This holds error state from the main graphics arbiter mainly involving
the DMA engine and address translation.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This is the same value as before, but it just makes the code slightly
more readable to use the local variable than converting the aperture
size into bytes every time.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
More precisely: For those that _need_ to be mappable. Also add two
BUG_ONs in fault and pin to check the consistency of the mappable
flag.
Changes in v2:
- Add tracking of gtt mappable space (to notice mappable/unmappable
balancing issues).
- Improve the mappable working set tracking by tracking fault and pin
separately.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This way we can make some more educated guesses as to why exactly
we can't use 2G apertures to their full potential ;)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
At least the part that's currently enabled by the BIOS.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
In i915_gem_object_pin obviously unbind only if mappable is true.
This is the last part to enable gtt_mappable_end != gtt_size, which
the next patch will do.
v2: Fences on g33/pineview only work in the mappable part of the
gtt.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Like before add a parameter mappable (also to gem_object_pin) and
set it depending upon the context. Only bos that are brought into
the gtt due to an execbuffer call can be put into the unmappable
part of the gtt, everything else (especially pinned objects) need
to be put into the mappable part of the gtt.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Add a mappable parameter to i915_gem_evict_something to distinguish
the two cases (non-restricted vs. mappable gtt allocations). No
functional changes because the mappable limit is set to the end of
the gtt currently.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Currently, we believe the GPU is idle if just the RENDER ring is idle.
This is obviously wrong if we only using either the BLT or the BSD
rings and so masking genuine hangs.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Preparing the ringbuffer for adding new commands can fail (a timeout
whilst waiting for the GPU to catch up and free some space). So check
for any potential error before overwriting HEAD with new commands, and
propagate that error back to the user where possible.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
"depth" should be signed in case packed_depth_bytes() returns -EINVAL.
This probably doesn't make a difference at runtime. In the original
code we would return -EINVAL later if (rec->offset_Y % 4294967274) is
non-zero.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The ringbuffer keeps a pointer to the parent device, so we can use that
instead of passing around the pointer on the stack.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Hi,
while I looked through your changes in drm-intel git tree (as I've got
a pressure for supporting DisplayPort audio), I stumbled on the
possible bug in the commit a9756bb5b2
Author: Zhenyu Wang <zhenyuw@linux.intel.com>
Date: Sun Sep 19 13:09:06 2010 +0800
drm/i915: Enable DisplayPort audio
In this commit, you changed the return value of g4x_dp_detect()
to "bit", but it should be "status", I suppose.
[ickle: mea culpa.]
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=31094
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
* 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (476 commits)
vmwgfx: Implement a proper GMR eviction mechanism
drm/radeon/kms: fix r6xx/7xx 1D tiling CS checker v2
drm/radeon/kms: properly compute group_size on 6xx/7xx
drm/radeon/kms: fix 2D tile height alignment in the r600 CS checker
drm/radeon/kms/evergreen: set the clear state to the blit state
drm/radeon/kms: don't poll dac load detect.
gpu: Add Intel GMA500(Poulsbo) Stub Driver
drm/radeon/kms: MC vram map needs to be >= pci aperture size
drm/radeon/kms: implement display watermark support for evergreen
drm/radeon/kms/evergreen: add some additional safe regs v2
drm/radeon/r600: fix tiling issues in CS checker.
drm/i915: Move gpu_write_list to per-ring
drm/i915: Invalidate the to-ring, flush the old-ring when updating domains
drm/i915/ringbuffer: Write the value passed in to the tail register
agp/intel: Restore valid PTE bit for Sandybridge after bdd3072
drm/i915: Fix flushing regression from 9af90d19f
drm/i915/sdvo: Remove unused encoding member
i915: enable AVI infoframe for intel_hdmi.c [v4]
drm/i915: Fix current fb blocking for page flip
drm/i915: IS_IRONLAKE is synonymous with gen == 5
...
Fix up conflicts in
- drivers/gpu/drm/i915/{i915_gem.c, i915/intel_overlay.c}: due to the
new simplified stack-based kmap_atomic() interface
- drivers/gpu/drm/vmwgfx/vmwgfx_drv.c: added .llseek entry due to BKL
removal cleanups.
Keep the current interface but ignore the KM_type and use a stack based
approach.
The advantage is that we get rid of crappy code like:
#define __KM_PTE \
(in_nmi() ? KM_NMI_PTE : \
in_irq() ? KM_IRQ_PTE : \
KM_PTE0)
and in general can stop worrying about what context we're in and what kmap
slots might be appropriate for that.
The downside is that FRV kmap_atomic() gets more expensive.
For now we use a CPP trick suggested by Andrew:
#define kmap_atomic(page, args...) __kmap_atomic(page)
to avoid having to touch all kmap_atomic() users in a single patch.
[ not compiled on:
- mn10300: the arch doesn't actually build with highmem to begin with ]
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix up drivers/gpu/drm/i915/intel_overlay.c]
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Miller <davem@davemloft.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
... to prevent flush processing of an idle (or even absent) ring.
This fixes a regression during suspend from 87acb0a5.
Reported-and-tested-by: Alexey Fisher <bug-track@fisher-privat.net>
Tested-by: Peter Clifton <pcjc2@cam.ac.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
When the object has been written to by the gpu it remains on the ring
until its flush has been retired. However, when the object is moving to
the ring and the associated cache needs to be invalidated, we need to
perform the flush on the target ring, not the one it came from (which is
NULL in the reported case and so the flush was entirely absent).
Reported-by: Peter Clifton <pcjc2@cam.ac.uk>
Reported-and-tested-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
This should fix the error along the reset path were we tried to clear the
tail register by setting it to 0, but were in fact setting it to the
current value and complaining when it did not reset to 0.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Whilst moving the code around in 9af90d19f, I dropped the or'ing in of
new write domains which would zero out the write domain for a render
target if later reused as a source later in the batch. This meant that
we might drop a required flush before reading from the render target.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=31043
Reported-by: xunx.fang@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This block is only used when detecting whether the connector is HDMI and
never again, so scope the variable to the detection routine.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This patch enables the sending of AVI infoframes in
drivers/gpu/drm/i915/intel_hdmi.c.
My receiver currently loses sync when the HDMI output on my computer
(DG45FC motherboard) is switched from 800x600 (the BIOS resolution) to
1920x1080 as part of the boot. Fixable by switching inputs on the receiver
a couple of times.
With this patch, my receiver has not lost sync yet (> 40 tries).
Fourth version, now based on drm-intel-next from:
git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel.git
Two questions still remain:
I'm assuming that the sdvo hardware also stores a header ECC byte in
the MSB of the first dword - is this correct?
Does the SDVOB and SDVOC handling in intel_hdmi_set_avi_infoframe()
look correct?
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Block execbuffer for the fb to be flipped away, not the one that is to
be flipped in.
[ickle: rewritten for -next]
Signed-off-by: Chia-I Wu <olvaffe@gmail.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Based on an original patch by Zhenyu Wang, this initializes the BLT ring for
SandyBridge and enables support for user execbuffers.
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
... before someone tries to use it. The code both calls
intel_ring_begin/advance() and open-codes the bookkeeping performed by
those two functions.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
In commit 8187a2b, the number of dwords used in the ringbuffer for
executing the batch buffer was erroneously changed from 2 to 4.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If the userspace driver is using a constant relocation array with a
static buffer, they will pass the same relocation array back to the
kernel. So we *do* need to update the presumed offset value in those
relocations to reflect the current object so that they remain correct
with future batchbuffers and we avoid the necessity of having to suspend
execution and perform redundant relocations.
Fixes the regression introduced by 12f889c for applications using
absolute addressing on trees of buffer (i.e. the current consumers of
libdrm_intel.so).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30996
Reported-by: Wang, Jinjin <jinjin.wang@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
To handle retirements, we need per-ring tracking of active objects.
To handle evictions, we need global tracking of active objects.
As we enable more rings, rebuilding the global list from the individual
per-ring lists quickly grows tiresome and overly complicated. Tracking the
active objects in two lists is the lesser of two evils.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
... by always initialising the empty ringbuffer it is always then safe
to check whether it is active.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The most frequent relocation within a batchbuffer is a contiguous sequence
of vertex buffer relocations, for which we can virtually eliminate the
drm_gem_object_lookup() overhead by caching the last handle to object
translation.
In doing so we refactor the pin and relocate retry loop out of
do_execbuffer into its own helper function and so improve the error
paths.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
One of the primarily consumers of the i915 driver is X, a large signal
driven application. Frequently when writing into the buffers, there is a
pending signal which causes us not to take the interruptible lock but
then we need to take that same lock around the object unreference. By
rearranging the code to do the interruptible lock as the first check, we
can avoid the frequent additional locking around the unreference.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
... to avoid reacquiring it to drop the object reference count on
exit. Note we have to make sure we now drop (and reacquire) the lock
around acquiring the mm semaphore on the slow paths.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
After allocation a handle for the fresh object, we know that we can
safely drop the refcnt without triggering a free so we do not need the
mutex. Strangely, this mutex acquisition is the one that appears on
driver profiles.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Avoid an early eviction of the batch buffer into the uncached GTT
domain, and so do the relocation fixup in cacheable memory.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
... perform an access validation check up front instead and copy them in
on-demand, during i915_gem_object_pin_and_relocate(). As around 20% of
the CPU overhead may be spent inside vmalloc for the relocation entries
when submitting an execbuffer [for x11perf -aa10text], the savings are
considerable and result in around a 10% throughput increase [for glyphs].
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Allow the user to override the detection of the sink's audio capabilities
from EDID. Not all sinks support the required EDID level to specify
whether they handle audio over the display connection, so allow the user
to enable it manually.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Allow the user to override the detection of the sink's audio capabilities
from EDID. Not all sinks support the required EDID level to specify
whether they handle audio over the display connection, so allow the user
to enable it manually.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Allow the user to override the detection of the sink's audio capabilities
from EDID. Not all sinks support the required EDID level to specify
whether they handle audio over the display connection, so allow the user
to enable it manually.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Rely on monitor's audio capability to turn on audio output for HDMI.
Tested-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This will turn on DP audio output by checking monitor's audio
capability.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
[ickle: rebase onto recent changes and rearranged for clarity]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The time between start of the pixel clock and backlight enable is a basic
panel timing constraint. If the Panel Power On/Off registers are found
to be 0, assume we are booting without VBIOS initialization and set these
registers to something reasonable.
Change-Id: Ibed6cc10d46bf52fd92e0beb25ae3525b5eef99d
Signed-off-by: Bryan Freed <bfreed@chromium.org>
[ickle: rearranged into a separate function to distinguish its role from
simply parsing the VBIOS tables.]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If userspace is submitting so many long running batches that the ring
becomes full, throttle by sleeping for a 1ms before checking for free
space. Simply yielding was causing excessive scheduler overhead whilst
making no progress.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
In i2c GPIO fallback, index 6 is reserved for nothing.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
FDI_PLL_BIOS_0 register is for Ironlake only, don't apply to
Sandybridge.
Original-patch-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Since the PLL may still be on, and the training pattern may not be
correct. Fixes suspend/resume on my PCH eDP test system.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: minor merge conflict and silence the compiler]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Freeing the Hardware Status Page was writing to the HWS register in
order to disable the GPU writing to the HWS page. Unfortunately, we were
writing to the mmio register after unmapping the register space, hence
the oops.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This reverts commit 6939a5aca7.
Daniel Vetter supplied a set of fixes for all the module unload bugs he
could trigger on his machines, so let the fun recommence!
The enter argument as implemented by commit 413d45d362 (drm, kdb, kms:
Add an enter argument to mode_set_base_atomic() API) should be more
descriptive as to what it does vs just passing 1 and 0 around.
There is no runtime behavior change as a result of this patch.
Reported-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
CC: David Airlie <airlied@linux.ie>
CC: dri-devel@lists.freedesktop.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
The i915 driver has quite a few module unload bugs, the known ones at
least have fixes that are targeting 2.6.37. However, in order to
maintain a stable kernel, we should prevent this known random memory
corruption following driver unload. This should have very low impact on
normal users who are unlikely to need to unload the i915 driver.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
On Sandybridge, the bit definition for hotplug on SDE has changed, so
update the code to new definition.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30378
Cc: stable@kernel.org
Signed-off-by: Yuanhan Liu <yuanhan.liu@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
After disabling the hotplug interrupts for VGA detection on Ironlake, be
sure to re-enable them again afterwards.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30378
Signed-off-by: Yuanhan Liu <yuanhan.liu@intel.com>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Needed on Ibex Peak and Cougar Point or the panel won't always come on.
Cc: stable@kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We don't use the CPU DP PLL with PCH attached eDP panels, so don't
bother to enable it.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We can skip most of the link training step if we use the VBT provided
values.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cache the first 4 bytes of DPCD data in the eDP case. It's unlikely to
change and can save us some trouble at link training time.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We do this later (and more properly) when we enable FDI, so we don't
need to do it here.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Wait for vblank after enabling a pipe, make the error messages more
informative, and wait for the pipe to turn off when we disable it.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
CPU eDP needs a different reference clock than PCH eDP, which uses the
standard PCH refclk of 120MHz.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Enable SSC on PCH eDP if possible.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: added a posting read of PCH_DREF_CONTROL before the udelay]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We need to use some of these values in eDP configurations, so be sure to
fetch them and store them in the i915 private structure.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The _DSM method on the integrated graphics device can tell us which
connectors are muxable, so add support for making the call and parsing
out the connector info.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: fix compiler warnings for using uninitialized 'result' and
downgrade error message for non-switchable devices]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Enable the panel before adjusting eDP link params, make sure the panel
is idle after powering it on before proceeding with other activity,
delay backlight enable to avoid visible flicker.
Also avoid using VDD per hw team recommendation; it can conflict with
the builtin panel power sequencing logic and lead to panel power
sequencing failures.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
FDI training needs to done and idle for PCH eDP and before we turn the
pipes on, and various eDP checks need to account for PCH attached eDP.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Since we set the output type of PCH attached eDP panels to
INTEL_OUTPUT_eDP this function would never return true when it should.
It's been replaced by working functions.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The display code needs to distinguish between CPU and PCH attached eDP
panels, so add some helpers to handle that.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
With the old check we'd never set lane_count or bpp to different values
on PCH attached eDP panels.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If is_edp is true, is_pch_edp will always be true. So limit the calls
to the latter function to places where the distinction actually matters.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Most of the PCH eDP checks are redundant, so document the functions in
preparation for removing most of the calls.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Currently, if a batch buffer refers to an object with a pending flip,
then we sleep until that pending flip is completed (unpinned and
signalled). This is so that a flip can be queued and the user can
continue rendering to the backbuffer oblivious to whether the buffer is
still pinned as the scan out. (The kernel arbitrating at the last moment
to stall the batch and wait until the buffer is unpinned and replaced as
the front buffer.)
As we only have a queue depth of 1, we can simply wait for the current
pending flip to complete and continue rendering. We can achieve this
with a single WAIT_FOR_EVENT command inserted into the ring buffer prior
to executing the batch, *without* stalling the client.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
A physically mapped hardware status page is allocated at driver load
time but was never freed. Call the existing code to free this page at
driver unload time on hardware which uses this kind.
Signed-off-by: Keith Packard <keithp@keithp.com>
[ickle: call before tearing down registers on KMS-only path, as pointed
out by Dave Airlie]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
since the handle references are all tied to a file_priv, and when it disappears
all the handle refs go with it.
The fbcon ones we'd only notice on unload, but the nouveau notifier one
would would happen on reboot.
nouveau: Reported-by: Marc Dionne <marc.c.dionne@gmail.com>
nouveau: Tested-by: Marc Dionne <marc.c.dionne@gmail.com>
i915 unload: Reported-by: Keith Packard <keithp@keithp.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some devices such as the radeon chips receive information from user
space which needs to be saved when executing an atomic mode set
operation, else the user space would have to be queried again for the
information.
This patch extends the mode_set_base_atomic() call to pass an argument
to indicate if this is an entry or an exit from an atomic kernel mode
set change. Individual drm drivers can properly save and restore
state accordingly.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: David Airlie <airlied@linux.ie>
CC: dri-devel@lists.freedesktop.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel:
drm/i915: Rephrase pwrite bounds checking to avoid any potential overflow
drm/i915: Sanity check pread/pwrite
drm/i915: Use pipe state to tell when pipe is off
drm/i915: vblank status not valid while training display port
drivers/gpu/drm/i915/i915_gem.c: Add missing error handling code
drm/i915: Fix refleak during eviction.
drm/i915: fix GMCH power reporting
lockdep spots that the fb_info->lock takes the dev->struct_mutex during
init (due to the device probing) and so we can not hold
dev->struct_mutex when unregistering the framebuffer. Simply reverse the
order of initialisation during cleanup and so do the intel_fbdev_fini()
before the intel_modeset_cleanup.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The display port DPMS state is tracked internally in the display port
driver so that when a hotplug event comes along, the driver can know
whether to try retraining the link. This doesn't work well if the
driver never sets the DPMS state to ON when the output is enabled.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cancel the output polling work proc before acquiring the struct mutex
to avoid acquiring the work proc mutex with the struct mutex
held. This avoids inverting the lock order seen when the work proc
runs.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Move the access control up from the fast paths, which are no longer
universally taken first, up into the caller. This then duplicates some
sanity checking along the slow paths, but is much simpler.
Tracked as CVE-2010-2962.
Reported-by: Kees Cook <kees@ubuntu.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Instead of waiting for the display line value to settle, we can simply
wait for the pipe configuration register 'state' bit to turn off.
Contrarywise, disabling the plane will not cause the display line
value to stop changing, so instead we wait for the vblank interrupt
bit to get set. And, we only do this when we're not about to wait for
the pipe to turn off.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
While the display port is in training mode, vblank interrupts don't
occur. Because we have to wait for the display port output to turn on
before starting the training sequence, enable the output in 'normal'
mode so that we can tell when a vblank has occurred, then start the
training sequence.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Extend the error handling code with operations found in other nearby error
handling code
A simplified version of the sematic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
@r@
statement S1,S2,S3;
constant C1,C2,C3;
@@
*if (...)
{... S1 return -C1;}
...
*if (...)
{... when != S1
return -C2;}
...
*if (...)
{... S1 return -C3;}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
The return from move_to_gtt_domain() may indicate a pending signal which
needs to handled as opposed to an actual error, for instance, so report
the original return value rather than forcing an EINVAL.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
vmwgfx: Fix fb VRAM pinning failure due to fragmentation
vmwgfx: Remove initialisation of dev::devname
vmwgfx: Enable use of the vblank system
vmwgfx: vt-switch (master drop) fixes
drm/vmwgfx: Fix breakage introduced by commit "drm: block userspace under allocating buffer and having drivers overwrite it (v2)"
drm: Hold the mutex when dropping the last GEM reference (v2)
drm/gem: handlecount isn't really a kref so don't make it one.
drm: i810/i830: fix locked ioctl variant
drm/radeon/kms: add quirk for MSI K9A2GM motherboard
drm/radeon/kms: fix potential segfault in r600_ioctl_wait_idle
drm: Prune GEM vma entries
drm/radeon/kms: fix up encoder info messages for DFP6
drm/radeon: fix PCI ID 5657 to be an RV410
The issue is that we may become stuck executing a long running shader
and continually attempt to reset the GPU. (Or maybe we tickle some bug
and need to break the vicious cycle.) So if we are detect a second hang
within 5 seconds, give up trying to programme the GPU and report it
wedged.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
So far only found registers for i830, i845, i865 and one of those has no
effect on i865!
At this moment in time, attempting to reset i8xx is a little
optimistic...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
When the GPU is reset, the fence registers are invalidated, so release
the objects and clear them out.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Only drm/i915 does the bookkeeping that makes the information useful,
and the information maintained is driver specific, so move it out of the
core and into its single user.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Airlie <airlied@redhat.com>
Now that we hold onto a reference whilst evicting objects, we need to
be sure that we drop all the references taken -- even on the error
paths.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
There were lots of places being inconsistent since handle count
looked like a kref but it really wasn't.
Fix this my just making handle count an atomic on the object,
and have it increase the normal object kref.
Now i915/radeon/nouveau drivers can drop the normal reference on
userspace object creation, and have the handle hold it.
This patch fixes a memory leak or corruption on unload, because
the driver had no way of knowing if a handle had been actually
added for this object, and the fbcon object needed to know this
to clean itself up properly.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Added a function that sets the LVDS values to default settings. This
will be called by intel_init_bios before checking for the VBT (video BIOS
table). The default values are thus loaded regardless of whether a VBT
is found.
The default settings in each parse function have been moved to the new
function. This consolidates all the default settings into one place.
The default dither bit value has been changed from 0 to 1. We can
assume that display devices will want dithering enabled.
Signed-off-by: Simon Que <sque@chromium.org>
Acked-by: Olof Johansson <olof@lixom.net>
[ickle: fixup for -next]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
At that point as the object is no longer in any GPU write domain it must
not be on the list, so the list_del() is redundant.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Just reschedule the retire requests again if the device is currently
busy. The request list will be pruned along other paths so will never
grow unbounded and so we can afford to miss the occasional pruning.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Yuanhan Liu
Chris Wilson
David Flynn
Dave Airlie
Daniel Vetter
Eric Anholt
Keith Packard
Alex Shi
Zou Nan hai
Jean Delvare
Joe Perches
Zhenyu Wang
Zhenyu Wang
Kyle McMartin
Jesse Barnes
Christoph Fritz
Dan Carpenter
Takashi Iwai
Linus Torvalds
Peter Zijlstra
David Härdeman
Chia-I Wu
Andrea Gelmini
Bryan Freed
Jason Wessel
Arnd Bergmann
Yuanhan Liu
Julia Lawall
Simon Que