Just like every other family BCM4908 should get its own enum value. That
is required to properly handle it in chipset conditional code.
The real change is excluding BCM4908 from the PLL reprogramming code
(see brcmusb_usb3_pll_54mhz()). I'm not sure what's the BCM4908
reference clock frequency but:
1. BCM4908 custom driver from Broadcom's SDK doesn't reprogram PLL
2. Doing that in Linux driver stopped PHY handling some USB 3.0 devices
This change makes USB 3.0 PHY recognize e.g.:
1. 04e8:6860 - Samsung Electronics Co., Ltd Galaxy series, misc. (MTP mode)
2. 1058:259f - Western Digital My Passport 259F
Broadcom's STB SoCs come with a set of SUN_TOP_CTRL_* registers that
allow reading chip family and product ids. Such a block & register is
missing on BCM4908 so this commit introduces "compatible" string
specific binding.
Fixes: 4b402fa8e0 ("phy: phy-brcm-usb: support PHY on the BCM4908")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220218172459.10431-1-zajec5@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Some Android x86 tablets with a Bay Trail (BYT) SoC and a Crystal Cove
PMIC, which does not support charger-detection, rely on a TUSB1211
phy for charger-detection.
Add support for charger detection on TUSB1211 phy-s and export
the information about the detected charger through the standard
power_supply class interface. power_supply class charger IC drivers
like the bq24190_charger.c driver will then pick this up and set
their input_current_limit based on this.
Note the "linux,phy_charger_detect" property used to enable this is
a special kernel-internal (so not part of the dt-bindings) property
used by dwc3 platform code to indicate that the phy needs to do
charger-detection.
Changes by Hans de Goede:
- Use "linux,phy_charger_detect" property to enable charger-detect
- Switch from a linear flow to a state-machine, with retries on
ulpi communication errors
- Use SW_CONTROL bit to disable the FSM when detection is finished
- Do a phy-reset on disconnect to work around the phy often refusing
ulpi_read()/_write() commands after a disconnect
- Use power_supply_reg_notifier() for Vbus monitoring
- Export the detection result through a power_supply class device
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Co-developed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220213130524.18748-10-hdegoede@redhat.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Now that we actually log errors on ulpi_write failures it becomes clear
that the ulpi_write() restoring the phy-parameters on power-on is failing
after a suspend/resume add a short delay after driving the cs line high
to fix this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220213130524.18748-9-hdegoede@redhat.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Since commit eb445a15fa ("phy: tusb1210: use bitmasks to set
VENDOR_SPECIFIC2") tusb->vendor_specific2 always contains a valid value
so there no need to check that it is set.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220213130524.18748-8-hdegoede@redhat.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
ulpi_read() and ulpi_write() calls can fail. Add wrapper functions to log
errors when this happens and add error checking to the read + write of
the phy parameters from the TUSB1210_VENDOR_SPECIFIC2 register.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220213130524.18748-7-hdegoede@redhat.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
According to the comment of the function phy_mipi_dphy_get_default_config(),
it uses minimum D-PHY timings based on MIPI D-PHY specification. They are
derived from the valid ranges specified in Section 6.9, Table 14, Page 41
of the D-PHY specification (v1.2). The table 14 explicitly mentions that
the minimum T-LPX parameter is 50 nanoseconds and the minimum TA-SURE
parameter is T-LPX nanoseconds. Likewise, the kernel doc of the 'lpx' and
'ta_sure' members of struct phy_configure_opts_mipi_dphy mentions that
the minimum values are 50000 picoseconds and @lpx picoseconds respectively.
Also, the function phy_mipi_dphy_config_validate() checks if cfg->lpx is
less than 50000 picoseconds and if cfg->ta_sure is less than cfg->lpx,
which hints the same minimum values.
Without this patch, the function phy_mipi_dphy_get_default_config()
wrongly sets cfg->lpx to 60000 picoseconds and cfg->ta_sure to 2 * cfg->lpx.
So, let's correct them to 50000 picoseconds and cfg->lpx respectively.
Note that I've only tested the patch with RM67191 DSI panel on i.MX8mq EVK.
Help is needed to test with other i.MX8mq, Meson and Rockchip platforms,
as I don't have the hardwares.
Fixes: dddc97e823 ("phy: dphy: Add configuration helpers")
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Link: https://lore.kernel.org/r/20220216071257.1647703-1-victor.liu@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add "wake on" support for the newer Synopsis based XHCI only controller.
This works on the 72165 and 72164 and newer chips and does not work
on 7216 based systems. Also switch the USB sysclk to a slower clock
on suspend to save additional power in S2. The clock switch will only
save power on the 72165b0 and newer chips and is a nop on older chips.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220215032422.5179-1-f.fainelli@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
D1 has a register layout like A100 and H616, with the moved SIDDQ bit.
Unlike H616 it does not have any dependencies between PHY instances.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220203013558.11490-4-samuel@sholland.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
As Icenowy pointed out, newer manuals (starting with H6) actually
document the register block at offset 0x800 as "HCI controller and PHY
interface", also describe the bits in our "PMU_UNK1" register.
Let's put proper names to those "unknown" variables and symbols.
While we are at it, generalise the existing code by allowing a bitmap
of bits to clear and set, to cover newer SoCs: The A100 and H616 use a
different bit for the SIDDQ control.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220203013558.11490-3-samuel@sholland.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch implements a combo phy driver for Rockchip SoCs
with NaNeng IP block. This phy can be used as pcie-phy, usb3-phy,
sata-phy or sgmii-phy.
Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://lore.kernel.org/r/20220208091326.12495-4-yifeng.zhao@rock-chips.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Some legacy eDP sinks may not support SSC. The support for SSC is
indicated through an opts flag from the controller driver. This
change will enable SSC only if the sink supports it.
Signed-off-by: Sankeerth Billakanti <quic_sbillaka@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20220207161612.REPOST.v1.3.Ie81d594ec2327dae6410db359cc492484bab171f@changeid
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The sc7280 platform supports native eDP controller and PHY.
This change will add support for the eDP PHY on sc7280.
Signed-off-by: Sankeerth Billakanti <quic_sbillaka@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20220207161612.REPOST.v1.2.Iff75c0ea8499f0baf2aa5800f2c45c4128e2415a@changeid
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In some cases, a single SerDes instance can be shared between two different
processors, each using a separate link. In these cases, the SerDes
configuration is done in an earlier boot stage. Therefore, add support to
skip reconfiguring, if it is was already configured beforehand.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20220128072642.29188-1-a-govindraju@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fixes for bunch of drivers:
- clk params for dphy
- arg fix for mtk-tphy
- refcount leak fix for stm32
- bus width fix for zynqmp
- sentinel fix ti
- PHY_BRCM_USB Kconfig fix
- clk fix for usb phy
-----BEGIN PGP SIGNATURE-----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=Av3W
-----END PGP SIGNATURE-----
Merge tag 'phy-fixes-5.17' into next
Merge phy fixes for 5.17 into next branch to resolve the conflict
between fixes and next for upcoming patches
The D-PHY specification (v1.2) explicitly mentions that the T-CLK-PRE
parameter's unit is Unit Interval(UI) and the minimum value is 8. Also,
kernel doc of the 'clk_pre' member of struct phy_configure_opts_mipi_dphy
mentions that it should be in UI. However, the dphy core driver wrongly
sets 'clk_pre' to 8000, which seems to hint that it's in picoseconds.
So, let's fix the dphy core driver to correctly reflect the T-CLK-PRE
parameter's minimum value according to the D-PHY specification.
I'm assuming that all impacted custom drivers shall program values in
TxByteClkHS cycles into hardware for the T-CLK-PRE parameter. The D-PHY
specification mentions that the frequency of TxByteClkHS is exactly 1/8
the High-Speed(HS) bit rate(each HS bit consumes one UI). So, relevant
custom driver code is changed to program those values as
DIV_ROUND_UP(cfg->clk_pre, BITS_PER_BYTE), then.
Note that I've only tested the patch with RM67191 DSI panel on i.MX8mq EVK.
Help is needed to test with other i.MX8mq, Meson and Rockchip platforms,
as I don't have the hardwares.
Fixes: 2ed869990e ("phy: Add MIPI D-PHY configuration options")
Tested-by: Liu Ying <victor.liu@nxp.com> # RM67191 DSI panel on i.MX8mq EVK
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> # for phy-meson-axg-mipi-dphy.c
Tested-by: Neil Armstrong <narmstrong@baylibre.com> # for phy-meson-axg-mipi-dphy.c
Tested-by: Guido Günther <agx@sigxcpu.org> # Librem 5 (imx8mq) with it's rather picky panel
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Link: https://lore.kernel.org/r/20220124024007.1465018-1-victor.liu@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix following coccicheck warning:
./drivers/phy/mediatek/phy-mtk-tphy.c:994:6-29: duplicated argument
to && or ||
The efuse_rx_imp is duplicate. Here should be efuse_tx_imp.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220107025050.787720-1-wanjiabing@vivo.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use reset_control_rearm() call if an error occurs in case
phy_meson8b_usb2_power_on() fails after reset() has been called, or in
case phy_meson8b_usb2_power_off() is called i.e the resource is no longer
used and the reset line may be triggered again by other devices.
reset_control_rearm() keeps use of triggered_count sane in the reset
framework, use of reset_control_reset() on shared reset line should
be balanced with reset_control_rearm().
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Reported-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220111095255.176141-4-aouledameur@baylibre.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use the existing dev_err_probe() helper instead of open-coding the same
operation.
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Reported-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220111095255.176141-3-aouledameur@baylibre.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use reset_control_rearm() call if an error occurs in case
phy_meson_gxl_usb2_init() fails after reset() has been called ; or in case
phy_meson_gxl_usb2_exit() is called i.e the resource is no longer used
and the reset line may be triggered again by other devices.
reset_control_rearm() keeps use of triggered_count sane in the reset
framework. Therefore, use of reset_control_reset() on shared reset line
should be balanced with reset_control_rearm().
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Reported-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220111095255.176141-2-aouledameur@baylibre.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Freescale/NXP i.MX8 USB3, MIPI DSI, and PCIE PHYs are only present
on the NXP i.MX8 family of SoCs. Hence wrap the config symbols for
these PHYs inside a check for ARCH_MXC && ARM64, to prevent asking the
user about these drivers when configuring a kernel without NXP i.MX SoC
family support.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Link: https://lore.kernel.org/r/393868affd830016d35f0d9aba32ccd7098c8073.1641987369.git.geert+renesas@glider.be
Signed-off-by: Vinod Koul <vkoul@kernel.org>
TX_PROT_BUS_WIDTH and RX_PROT_BUS_WIDTH are single registers with
separate bit fields for each lane. The code in xpsgtr_phy_init_sgmii was
not preserving the existing register value for other lanes, so enabling
the PHY in SGMII mode on one lane zeroed out the settings for all other
lanes, causing other PS-GTR peripherals such as USB3 to malfunction.
Use xpsgtr_clr_set to only manipulate the desired bits in the register.
Fixes: 4a33bea003 ("phy: zynqmp: Add PHY driver for the Xilinx ZynqMP Gigabit Transceiver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20220126001600.1592218-1-robert.hancock@calian.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There are two bugs in the error handling:
1: If devm_of_phy_provider_register() fails then there was no cleanup.
2: The error handling called of_node_put(child) improperly leading to
a use after free. We are only holding the reference inside the loop
so the last two gotos after the loop lead to a use after free bug.
Fix this by cleaning up the partial allocations (or partial iterations)
in the loop before doing the goto.
Fixes: a43f72ae13 ("phy: cadence: Sierra: Change MAX_LANES of Sierra to 16")
Fixes: 44d30d6228 ("phy: cadence: Add driver for Sierra PHY")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20220115115146.GC7552@kili
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The previous commit 4b402fa8e0 ("phy: phy-brcm-usb: support PHY on
the BCM4908") added a second "default" line for ARCH_BCM_4908 above
the original "default" line for ARCH_BRCMSTB. When two "default"
lines are used, only the first is used and this change stopped
the PHY_BRCM_USB option for being enabled for ARCH_BRCMSTB.
The fix is to use one "default line with "||".
Fixes: 4b402fa8e0 ("phy: phy-brcm-usb: support PHY on the BCM4908")
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211201180653.35097-4-alcooperx@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The PHY client driver does a phy_exit() call on suspend or rmmod and
the PHY driver needs to know the difference because some clocks need
to be kept running for suspend but can be shutdown on unbind/rmmod
(or if there are no PHY clients at all).
The fix is to use a PM notifier so the driver can tell if a PHY
client is calling exit() because of a system suspend or a driver
unbind/rmmod.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211201180653.35097-2-alcooperx@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Here is the large set of char, misc, and other "small" driver subsystem
changes for 5.17-rc1.
Lots of different things are in here for char/misc drivers such as:
- habanalabs driver updates
- mei driver updates
- lkdtm driver updates
- vmw_vmci driver updates
- android binder driver updates
- other small char/misc driver updates
Also smaller driver subsystems have also been updated, including:
- fpga subsystem updates
- iio subsystem updates
- soundwire subsystem updates
- extcon subsystem updates
- gnss subsystem updates
- phy subsystem updates
- coresight subsystem updates
- firmware subsystem updates
- comedi subsystem updates
- mhi subsystem updates
- speakup subsystem updates
- rapidio subsystem updates
- spmi subsystem updates
- virtual driver updates
- counter subsystem updates
Too many individual changes to summarize, the shortlog contains the full
details.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYeGNAQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymoVgCg1CPjMu8/SDj3Sm3a1UMQJn9jnl8AnjQcEp3z
hMr9mISG4r6g4PvjrJBj
=9May
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver updates from Greg KH:
"Here is the large set of char, misc, and other "small" driver
subsystem changes for 5.17-rc1.
Lots of different things are in here for char/misc drivers such as:
- habanalabs driver updates
- mei driver updates
- lkdtm driver updates
- vmw_vmci driver updates
- android binder driver updates
- other small char/misc driver updates
Also smaller driver subsystems have also been updated, including:
- fpga subsystem updates
- iio subsystem updates
- soundwire subsystem updates
- extcon subsystem updates
- gnss subsystem updates
- phy subsystem updates
- coresight subsystem updates
- firmware subsystem updates
- comedi subsystem updates
- mhi subsystem updates
- speakup subsystem updates
- rapidio subsystem updates
- spmi subsystem updates
- virtual driver updates
- counter subsystem updates
Too many individual changes to summarize, the shortlog contains the
full details.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (406 commits)
counter: 104-quad-8: Fix use-after-free by quad8_irq_handler
dt-bindings: mux: Document mux-states property
dt-bindings: ti-serdes-mux: Add defines for J721S2 SoC
counter: remove old and now unused registration API
counter: ti-eqep: Convert to new counter registration
counter: stm32-lptimer-cnt: Convert to new counter registration
counter: stm32-timer-cnt: Convert to new counter registration
counter: microchip-tcb-capture: Convert to new counter registration
counter: ftm-quaddec: Convert to new counter registration
counter: intel-qep: Convert to new counter registration
counter: interrupt-cnt: Convert to new counter registration
counter: 104-quad-8: Convert to new counter registration
counter: Update documentation for new counter registration functions
counter: Provide alternative counter registration functions
counter: stm32-timer-cnt: Convert to counter_priv() wrapper
counter: stm32-lptimer-cnt: Convert to counter_priv() wrapper
counter: ti-eqep: Convert to counter_priv() wrapper
counter: ftm-quaddec: Convert to counter_priv() wrapper
counter: intel-qep: Convert to counter_priv() wrapper
counter: microchip-tcb-capture: Convert to counter_priv() wrapper
...
- New support:
- Qualcomm eDP PHY driver
- Qualcomm SM8450 UFS, USB2, USB3, PCIe0 and PCIe1 phy support
- Lan966x ethernet serdes PHY driver
- Support for uniphier NXI & Pro4 SoC
- Qualcomm SM6350 USB2 support
- Amlogic Meson8 HDMI TX PHY driver
- Rockchip rk3568 usb2 support
- Intel Thunder Bay eMMC PHY driver
- Freescale IMX8 PCIe phy driver
- Updates:
- Cadence Sierra driver updates for multilink configurations
- Bcm usb2 updates for Phy reg space
-----BEGIN PGP SIGNATURE-----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=29yF
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy into char-misc-next
Vinod writes:
phy-for-5.17
- New support:
- Qualcomm eDP PHY driver
- Qualcomm SM8450 UFS, USB2, USB3, PCIe0 and PCIe1 phy support
- Lan966x ethernet serdes PHY driver
- Support for uniphier NXI & Pro4 SoC
- Qualcomm SM6350 USB2 support
- Amlogic Meson8 HDMI TX PHY driver
- Rockchip rk3568 usb2 support
- Intel Thunder Bay eMMC PHY driver
- Freescale IMX8 PCIe phy driver
- Updates:
- Cadence Sierra driver updates for multilink configurations
- Bcm usb2 updates for Phy reg space
* tag 'phy-for-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (72 commits)
phy: cadence: Sierra: Add support for derived reference clock output
dt-bindings: phy: cadence-sierra: Add clock ID for derived reference clock
phy: cadence: Sierra: Add PCIe + QSGMII PHY multilink configuration
phy: cadence: Sierra: Add support for PHY multilink configurations
phy: cadence: Sierra: Fix to get correct parent for mux clocks
phy: cadence: Sierra: Update single link PCIe register configuration
phy: cadence: Sierra: Check PIPE mode PHY status to be ready for operation
phy: cadence: Sierra: Check cmn_ready assertion during PHY power on
phy: cadence: Sierra: Add PHY PCS common register configurations
phy: cadence: Sierra: Rename some regmap variables to be in sync with Sierra documentation
phy: cadence: Sierra: Add support to get SSC type from device tree
dt-bindings: phy: cadence-sierra: Add binding to specify SSC mode
dt-bindings: phy: cadence-torrent: Rename SSC macros to use generic names
phy: cadence: Sierra: Prepare driver to add support for multilink configurations
phy: cadence: Sierra: Use of_device_get_match_data() to get driver data
phy: mediatek: Fix missing check in mtk_mipi_tx_probe
phy: uniphier-usb3ss: fix unintended writing zeros to PHY register
phy: phy-mtk-tphy: use new io helpers to access register
phy: phy-mtk-xsphy: use new io helpers to access register
phy: mediatek: add helpers to update bits of registers
...
Sierra has derived differential reference clock output which is sourced
after the spread spectrum generation has been added. Add support to drive
derived reference clock out of serdes. Model this derived clock as a
"clock" so that platforms using this can enable it.
Sierra Main LC VCO PLL divider 1 clock is programmed to output 100MHz
clock output.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20211223060137.9252-16-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add register sequences for PCIe + QSGMII PHY multilink configuration.
PHY configuration for multi-link operation is done in two steps.
e.g. Consider a case for a 4 lane PHY with PCIe using 2 lanes and QSGMII
other 2 lanes. Sierra PHY has 2 PLLs, viz. PLLLC and PLLLC1. So in this
case, PLLLC is used for PCIe and PLLLC1 is used for QSGMII.
PHY is configured in two steps as described below.
[1] For first step, the register values are selected as
[TYPE_PCIE][TYPE_QSGMII][ssc].
This will configure PHY registers associated for PCIe involving PLLLC
registers and registers for first 2 lanes of PHY.
[2] In second step, the register values are selected as
[TYPE_QSGMII][TYPE_PCIE][ssc].
This will configure PHY registers associated for QSGMII involving
PLLLC1 registers and registers for other 2 lanes of PHY.
This completes the PHY configuration for multilink operation.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20211223060137.9252-14-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for multilink configuration of Sierra PHY. Currently,
maximum two links are supported.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20211223060137.9252-13-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix get_parent() callback to return the correct index of the parent for
PLL_CMNLC1 clock. Add a separate table of register values corresponding
to the parent index for PLL_CMNLC1. Update set_parent() callback
accordingly.
Fixes: 28081b7285 ("phy: cadence: Sierra: Model PLL_CMNLC and PLL_CMNLC1 as clocks (mux clocks)")
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20211223060137.9252-12-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add single link PCIe register configurations for no SSC and internal
SSC. Also, add missing PMA lane registers for external SSC.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20211223060137.9252-11-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
PIPE phy status is used to communicate the completion of several PHY
functions. Check if PHY is ready for operation while configured for
PIPE mode during startup.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20211223060137.9252-10-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Check if PMA cmn_ready is set indicating the startup process is complete.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20211223060137.9252-9-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Sierra driver currently supports single link configurations only. Prepare
driver to support multilink multiprotocol configurations along with
different SSC modes.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20211223060137.9252-3-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use of_device_get_match_data() to get driver data instead of boilerplate
code.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20211223060137.9252-2-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The of_device_get_match_data() function may return NULL.
Add check to prevent potential null dereference.
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20211224082103.7658-1-linmq006@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Due to some SoCs have a bit shift issue that will drop a bit for usb3
phy or pcie phy, fix it by adding software efuse reading and setting,
but only support it optionally for version 2/3.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20211218082802.5256-2-chunfeng.yun@mediatek.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There are two different PCIe PHYs on SM8450, one having one lane (v5)
and another with two lanes (v5.20). This commit adds support for the
second PCIe phy.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211218141754.503661-3-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The rk3568 usb2phy is a standalone device with a single muxed interrupt.
Add support for the registers to the usb2phy driver.
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Michael Riesch <michael.riesch@wolfvision.net>
Link: https://lore.kernel.org/r/20211215210252.120923-7-pgwipeout@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The rk3568 usb2phy has a single muxed interrupt that handles all
interrupts.
Allow the driver to plug in only a single interrupt as necessary.
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Michael Riesch <michael.riesch@wolfvision.net>
Link: https://lore.kernel.org/r/20211215210252.120923-6-pgwipeout@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
New Rockchip devices have the usb2 phy devices as standalone nodes
instead of children of the grf node.
Allow the driver to find the grf node from a phandle.
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Michael Riesch <michael.riesch@wolfvision.net>
Link: https://lore.kernel.org/r/20211215210252.120923-5-pgwipeout@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
New Rockchip devices have the usb phy nodes as standalone devices.
These nodes have register nodes with #address_cells = 2, but only use 32
bit addresses.
Adjust the driver to check if the returned address is "0", and adjust
the index in that case.
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Michael Riesch <michael.riesch@wolfvision.net>
Link: https://lore.kernel.org/r/20211215210252.120923-4-pgwipeout@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There are two different PCIe PHYs on SM8450, one having one lane (v5)
and another with two lanes (v5.20). This commit adds support for the
first PCIe phy only, support for the second PCIe PHY is coming in next
commits.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211214225846.2043361-4-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for the USB DP & UNI PHYs found on SM8450. This is same as
the phy version used on SM8350 and sequences turned out to be same, so
use the same table from SM8350 for this as well.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211213131450.535775-3-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
kernel test robot complains about missing FIELD_PREP, so include
bitfield.h for that
drivers/phy/freescale/phy-fsl-imx8m-pcie.c:41:37: error: implicit declaration of function 'FIELD_PREP' [-Werror=implicit-function-declaration]
drivers/phy/freescale/phy-fsl-imx8m-pcie.c:41:41: error: implicit declaration of function 'FIELD_PREP' [-Werror=implicit-function-declaration]
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 1aa97b0022 ("phy: freescale: pcie: Initialize the imx8 pcie standalone phy driver")
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Link: https://lore.kernel.org/r/20211215060834.921617-1-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Variable delay is being assigned to zero and the code falls through to
the next case in a switch statement that returns out of the function.
The variable is never read in this scenario and so the assignment is
redundant and can be removed.
Cleans up scan-build static analysis warning:
drivers/phy/rockchip/phy-rockchip-inno-usb2.c:753:3: warning: Value
stored to 'delay' is never read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20211211180054.525368-1-colin.i.king@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Remove the set_speed function and allow the driver to figure out the
speed at which needs to configure the serdes based on the interface type.
Fixes: 305524902a ("phy: Add lan966x ethernet serdes PHY driver")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20211211214717.1284306-1-horatiu.vultur@microchip.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
callers of tegra_xusb_find_port_node() function only do NULL checking for
the return value. return NULL instead of ERR_PTR(-ENOMEM) to keep
consistent.
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20211213020507.1458-1-linmq006@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use struct_size() to get the accurate size of `clk_hw_onecell_data`
with a variable size array, instead of sizeof(data) to get the size
of a pointer.
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Guo Zhengkui <guozhengkui@vivo.com>
Fixes: f199223cb4 ("phy: qcom: Introduce new eDP PHY driver")
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211209032114.9416-1-guozhengkui@vivo.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
SM8450 UFS seems to use same sequence as SM8350, so reuse the sequence
from SM8450. Add the new clock list for this phy and the new compatible
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Co-developed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20211201074456.3969849-4-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Currently the driver is supporting only the interfaces QSGMII, SGMII,
RGMII and GMII. This patch extend the supported interfaces with
1000BASE-X and 2500BASE-X.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20211130101015.164916-1-horatiu.vultur@microchip.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Link: https://lore.kernel.org/r/1637822289-24534-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Change stm32-usbphyc driver to use dev_err_probe(), to benefit of
devices_deferred debugfs in case of probe deferral.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Reviewed-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/1635172265-26219-1-git-send-email-fabrice.gasnier@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Improve message & use dev_err_probe() helper which prints actual error
(helpful for debugging) and deals with -EPROBE_DEFER.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211123221521.25323-1-zajec5@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for PHY_INTERFACE_MODE_5GBASER mode within the Marvell CP110
common PHY driver.
This is currently only supported via SMC calls to TF-A. Legacy support
may be added later, if needed.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support of eMMC PHY for Intel Thunder Bay SoC,
uses the Arasan eMMC phy
Signed-off-by: Rashmi A <rashmi.a@intel.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20211027115516.4475-5-rashmi.a@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In some cases the standby/enable gpio can be pulled low/high and would not
be connected to a gpio. The current driver implementation will return an
error in these cases. Therefore, make devm_gpiod_get optional.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20211102112120.23637-1-a-govindraju@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use the macro 'swap()' defined in 'include/linux/minmax.h' to avoid
opencoding it.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Yang Guang <yang.guang5@zte.com.cn>
Link: https://lore.kernel.org/r/20211104065233.1833499-1-yang.guang5@zte.com.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for PHY interface built into ahci controller implemented
in UniPhier Pro4 SoC.
Pro4 SoC distinguishes it from other SoCs as "legacy" SoC, which has GIO
clock line. And Pro4 AHCI-PHY needs to control additional reset lines
("pm", "tx", and "rx").
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1635503947-18250-9-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Amlogic Meson8/8b/8m2 have a built-in HDMI PHY in the HHI register
region. Unfortunately only few register bits are documented. For
HHI_HDMI_PHY_CNTL0 the magic numbers are taken from the 3.10 vendor
kernel.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20211020195107.1564533-3-martin.blumenstingl@googlemail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This should check ">pmctrl" instead of "->sysctrl". This bug could
potentially lead to a crash if we dereference the error pointer.
Fixes: 73075011ff ("phy: HiSilicon: Add driver for Kirin 970 PCIe PHY")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/20211117074843.GE5237@kili
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Many recent Qualcomm platforms comes with native DP and eDP support.
This consists of a controller in the MDSS and a QMP-like PHY.
While similar to the well known QMP block, the eDP PHY only has TX lanes
and the programming sequences are slightly different. Rather than
continuing the trend of parameterize the QMP driver to pieces, this
introduces the support as a new driver.
The registration of link and pixel clocks are borrowed from the QMP
driver. The non-DP link frequencies are omitted for now.
The eDP PHY is very similar to the dedicated (non-USB) DP PHY, but only
the prior is supported for now.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20211103234410.1352424-2-bjorn.andersson@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The documentation uses incorrect style, so fix that.
drivers/phy/ti/phy-omap-usb2.c:102: warning: Function parameter or member 'comparator' not described in 'omap_usb2_set_comparator'
While at it, use a single line for function description
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Liam Beguin <liambeguin@gmail.com>
Link: https://lore.kernel.org/r/20211120061531.410771-2-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The functions are documented but there were style issues, so fix
the style and add missing description for phy_dwc3
drivers/phy/qualcomm/phy-qcom-ipq806x-usb.c:130:
drivers/phy/qualcomm/phy-qcom-ipq806x-usb.c:174:
drivers/phy/qualcomm/phy-qcom-ipq806x-usb.c:212: warning:
This comment starts with '/**', but isn't a kernel-doc comment.
Refer Documentation/doc-guide/kernel-doc.rst
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211120061531.410771-1-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Updated DT binding maps just a PHY's register space instead of the whole
DMU block. Accessing a common CRU reg is handled using syscon &
regmap.
The old binding has been deprecated and remains supported as a fallback
method.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20211026093716.5567-1-zajec5@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The comment is not kernel-doc one and starts with /**, so fix that.
drivers/phy/ti/phy-tusb1210.c:16: warning: expecting prototype for tusb1210.c(). Prototype was for TUSB1210_VENDOR_SPECIFIC2() instead
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Liam Beguin <liambeguin@gmail.com>
Link: https://lore.kernel.org/r/20211116103951.34482-6-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The comment is not kernel-doc one and starts with /**, so fix that.
drivers/phy/qualcomm/phy-qcom-usb-hsic.c:3: warning:
This comment starts with '/**', but isn't a kernel-doc comment.
Refer Documentation/doc-guide/kernel-doc.rst
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211116103951.34482-4-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
dp-* members were added to qmp_phy_combo_cfg but documentation was
missed, so add that.
drivers/phy/qualcomm/phy-qcom-qmp.c:2995: warning: Function parameter or member 'dp_aux_cfg' not described in 'qmp_phy'
drivers/phy/qualcomm/phy-qcom-qmp.c:2995: warning: Function parameter or member 'dp_opts' not described in 'qmp_phy'
drivers/phy/qualcomm/phy-qcom-qmp.c:2995: warning: Function parameter or member 'dp_clks' not described in 'qmp_phy'
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211116103951.34482-3-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix the format and add description for ops to fix the below warnings:
drivers/phy/marvell/phy-mvebu-cp110-utmi.c:94: warning: Function parameter or member 'syscon' not described in 'mvebu_cp110_utmi'
drivers/phy/marvell/phy-mvebu-cp110-utmi.c:94: warning: Function parameter or member 'ops' not described in 'mvebu_cp110_utmi'
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20211116103951.34482-1-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Do not use "/**" to begin a non-kernel-doc comment.
Fixes these build warnings:
drivers/phy/ti/phy-am654-serdes.c:3: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* PCIe SERDES driver for AM654x SoC
drivers/phy/ti/phy-j721e-wiz.c:3: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Wrapper driver for SERDES used in J721E
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: linux-phy@lists.infradead.org
Link: https://lore.kernel.org/r/20211115030559.13994-1-rdunlap@infradead.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
st,decrease-hs-slew-rate is described in phy-stm32-usbphyc.yaml. Then
fix the property name in driver.
Fixes: 2f5e9f815a ("phy: stm32: add phy tuning support")
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211026154817.198937-1-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Here is the big set of char and misc and other tiny driver subsystem
updates for 5.16-rc1.
Loads of things in here, all of which have been in linux-next for a
while with no reported problems (except for one called out below.)
Included are:
- habanana labs driver updates, including dma_buf usage,
reviewed and acked by the dma_buf maintainers
- iio driver update (going through this tree not staging as they
really do not belong going through that tree anymore)
- counter driver updates
- hwmon driver updates that the counter drivers needed, acked by
the hwmon maintainer
- xillybus driver updates
- binder driver updates
- extcon driver updates
- dma_buf module namespaces added (will cause a build error in
arm64 for allmodconfig, but that change is on its way through
the drm tree)
- lkdtm driver updates
- pvpanic driver updates
- phy driver updates
- virt acrn and nitr_enclaves driver updates
- smaller char and misc driver updates
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYYPX2A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymUUgCbB4EKysgLuXYdjUalZDx+vvZO4k0AniS14O4k
F+2dVSZ5WX6wumUzCaA6
=bXQM
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char and misc and other tiny driver subsystem
updates for 5.16-rc1.
Loads of things in here, all of which have been in linux-next for a
while with no reported problems (except for one called out below.)
Included are:
- habanana labs driver updates, including dma_buf usage, reviewed and
acked by the dma_buf maintainers
- iio driver update (going through this tree not staging as they
really do not belong going through that tree anymore)
- counter driver updates
- hwmon driver updates that the counter drivers needed, acked by the
hwmon maintainer
- xillybus driver updates
- binder driver updates
- extcon driver updates
- dma_buf module namespaces added (will cause a build error in arm64
for allmodconfig, but that change is on its way through the drm
tree)
- lkdtm driver updates
- pvpanic driver updates
- phy driver updates
- virt acrn and nitr_enclaves driver updates
- smaller char and misc driver updates"
* tag 'char-misc-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (386 commits)
comedi: dt9812: fix DMA buffers on stack
comedi: ni_usb6501: fix NULL-deref in command paths
arm64: errata: Enable TRBE workaround for write to out-of-range address
arm64: errata: Enable workaround for TRBE overwrite in FILL mode
coresight: trbe: Work around write to out of range
coresight: trbe: Make sure we have enough space
coresight: trbe: Add a helper to determine the minimum buffer size
coresight: trbe: Workaround TRBE errata overwrite in FILL mode
coresight: trbe: Add infrastructure for Errata handling
coresight: trbe: Allow driver to choose a different alignment
coresight: trbe: Decouple buffer base from the hardware base
coresight: trbe: Add a helper to pad a given buffer area
coresight: trbe: Add a helper to calculate the trace generated
coresight: trbe: Defer the probe on offline CPUs
coresight: trbe: Fix incorrect access of the sink specific data
coresight: etm4x: Add ETM PID for Kryo-5XX
coresight: trbe: Prohibit trace before disabling TRBE
coresight: trbe: End the AUX handle on truncation
coresight: trbe: Do not truncate buffer on IRQ
coresight: trbe: Fix handling of spurious interrupts
...
In case of error, the function devm_ioremap() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value
check should be replaced with NULL test.
Fixes: 2ff8a1eeb5 ("phy: Add Sparx5 ethernet serdes PHY driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210909072149.2934047-1-yangyingliang@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The FSEL_MASK which selects the refclock is defined incorrectly.
It should be [4:6] not [5:7]. Due to this incorrect definition, the BIT(7)
in USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON0 is reset which keeps PHY analog
blocks ON during suspend.
Fix this issue by correctly defining the FSEL_MASK.
Fixes: 51e8114f80 ("phy: qcom-snps: Add SNPS USB PHY driver for QCOM based SOCs")
Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
Link: https://lore.kernel.org/r/1635135575-5668-1-git-send-email-quic_c_sanm@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix following coccicheck warning:
./drivers/phy/hisilicon/phy-hisi-inno-usb2.c:138:1-23: WARNING: Function
for_each_child_of_node should have of_node_put() before break
Early exits from for_each_child_of_node should decrement the
node reference counter.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Link: https://lore.kernel.org/r/20211015080154.16016-1-wanjiabing@vivo.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit f839f14e24 ("phy: qcom-qmp: Add sc8180x PCIe support") added
SC8180X PCIe tables, but used sm8250_qmp_pcie_serdes_tbl as a serdes
table because of the copy paste error. Commit bfccd9a71a ("phy:
qcom-qmp: Fix sc8180x PCIe definition") corrected part of this mistake
by pointing serdes_tbl to sc8180x_qmp_pcie_serdes_tbl, however the
serdes_tbl_num field was not updated to use sc8180x table. So let's now
fix the serdes_tbl_num field too.
Fixes: bfccd9a71a ("phy: qcom-qmp: Fix sc8180x PCIe definition")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211020155604.1374530-1-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support to output received reference clock. Model the received
reference clock as an alternate parent of reference clock driver
clock. When received refclk is selected to output on cmn_refclk_p/m,
this is the internal reference clock driven on the pma_cmn_refclk_int.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Link: https://lore.kernel.org/r/20210922123735.21927-5-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When reference clock driver is enabled, either derived or received refclk
is output on cmn_refclk_p/m. Update the reference clock driver
implementation by modelling reference clock driver as a "clock" with
derived reference clock set as its default parent. The support for
received reference clock will be added in a separate patch.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Link: https://lore.kernel.org/r/20210922123735.21927-4-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Smatch complains that if of_get_address() returns NULL, then "size"
isn't initialized. Also it would lead to an Oops.
Fixes: 7f78322cdd ("phy: ti: gmii-sel: retrieve ports number and base offset from dt")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20210914110038.GB11657@kili
Signed-off-by: Vinod Koul <vkoul@kernel.org>
It can be necessary to adjust the phys settings to compensate parasitics.
This patch adds support of new optional properties to configure the tune
interface of the phys of stm32-usbphyc.
Properties are optional, that's why each property is skipped if not
found (-EINVAL).
Phy tuning is restored on resume because if deep low power state is
achieved, phy tuning configuration is reset.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211015161427.220784-4-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
UTMI switch value can be lost during suspend/resume, depending on the power
state reached.
This patch adds resume function to usbphyc, to reconfigure utmi switch
after suspend.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211015161427.220784-2-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This converts users of mdiobus to mdiodev using the following semantic
patch:
@@
identifier mdiodev;
expression regnum;
@@
- mdiobus_read(mdiodev->bus, mdiodev->addr, regnum)
+ mdiodev_read(mdiodev, regnum)
@@
identifier mdiodev;
expression regnum, val;
@@
- mdiobus_write(mdiodev->bus, mdiodev->addr, regnum, val)
+ mdiodev_write(mdiodev, regnum, val)
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per downstream kernel, beside vdda-pll and vdda-phy-dpdm, vdd is also a
required supply for QUSB2 PHY digital circuit operation. The driver
works right now likely because firmware already sets it up. Add it for
correctness and completeness.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210928022002.26286-3-shawn.guo@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The helper function devm_add_action_or_reset() will internally
call devm_add_action(), and gif devm_add_action() fails then it will
execute the action mentioned and return the error code. So
use devm_add_action_or_reset() instead of devm_add_action()
to simplify the error handling, reduce the code.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20210922130024.745-1-caihuoqing@baidu.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The helper function devm_add_action_or_reset() will internally
call devm_add_action(), and gif devm_add_action() fails then it will
execute the action mentioned and return the error code. So
use devm_add_action_or_reset() instead of devm_add_action()
to simplify the error handling, reduce the code.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210922130017.692-1-caihuoqing@baidu.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Adding a configuration menu to hold many Broadcom phy drivers
helps to make the menu display more concise.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210923025013.189-1-caihuoqing@baidu.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Kirin 970 PHY is somewhat similar to the Kirin 960, but it
does a lot more. Add the needed bits for PCIe to start working on
HiKey 970 boards.
Co-developed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/b7a4ff41b57d861b003f1a00cae81f3d226fbe18.1632814194.git.mchehab+huawei@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We use everywhere "Samsung" and "Exynos", not the uppercase versions.
Describe better which driver applies to which SoC, to make configuring
kernel for Samsung SoC easier.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210924132658.109814-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Merge more updates from Andrew Morton:
"147 patches, based on 7d2a07b769.
Subsystems affected by this patch series: mm (memory-hotplug, rmap,
ioremap, highmem, cleanups, secretmem, kfence, damon, and vmscan),
alpha, percpu, procfs, misc, core-kernel, MAINTAINERS, lib,
checkpatch, epoll, init, nilfs2, coredump, fork, pids, criu, kconfig,
selftests, ipc, and scripts"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (94 commits)
scripts: check_extable: fix typo in user error message
mm/workingset: correct kernel-doc notations
ipc: replace costly bailout check in sysvipc_find_ipc()
selftests/memfd: remove unused variable
Kconfig.debug: drop selecting non-existing HARDLOCKUP_DETECTOR_ARCH
configs: remove the obsolete CONFIG_INPUT_POLLDEV
prctl: allow to setup brk for et_dyn executables
pid: cleanup the stale comment mentioning pidmap_init().
kernel/fork.c: unexport get_{mm,task}_exe_file
coredump: fix memleak in dump_vma_snapshot()
fs/coredump.c: log if a core dump is aborted due to changed file permissions
nilfs2: use refcount_dec_and_lock() to fix potential UAF
nilfs2: fix memory leak in nilfs_sysfs_delete_snapshot_group
nilfs2: fix memory leak in nilfs_sysfs_create_snapshot_group
nilfs2: fix memory leak in nilfs_sysfs_delete_##name##_group
nilfs2: fix memory leak in nilfs_sysfs_create_##name##_group
nilfs2: fix NULL pointer in nilfs_##name##_attr_release
nilfs2: fix memory leak in nilfs_sysfs_create_device_group
trap: cleanup trap_init()
init: move usermodehelper_enable() to populate_rootfs()
...
HZ unit conversion macros are available in units.h, use them and remove
the duplicate definition.
Link: https://lkml.kernel.org/r/20210816114732.1834145-11-daniel.lezcano@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Christian Eggers <ceggers@arri.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Lukasz Luba <lukasz.luba@arm.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=mKyO
-----END PGP SIGNATURE-----
Merge tag 'mips_5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
- converted Pistachio platform to use MIPS generic kernel
- fixes and cleanups
* tag 'mips_5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (29 commits)
MIPS: Malta: fix alignment of the devicetree buffer
MIPS: ingenic: Unconditionally enable clock of CPU #0
MIPS: mscc: ocelot: mark the phy-mode for internal PHY ports
MIPS: mscc: ocelot: disable all switch ports by default
MAINTAINERS: adjust PISTACHIO SOC SUPPORT after its retirement
MIPS: Return true/false (not 1/0) from bool functions
MIPS: generic: Return true/false (not 1/0) from bool functions
MIPS: Make a alias for pistachio_defconfig
MIPS: Retire MACH_PISTACHIO
MIPS: config: generic: Add config for Marduk board
pinctrl: pistachio: Make it as an option
phy: pistachio-usb: Depend on MIPS || COMPILE_TEST
clocksource/drivers/pistachio: Make it selectable for MIPS
clk: pistachio: Make it selectable for generic MIPS kernel
MIPS: DTS: Pistachio add missing cpc and cdmm
MIPS: generic: Allow generating FIT image for Marduk board
MIPS: locking/atomic: Fix atomic{_64,}_sub_if_positive
MIPS: loongson2ef: don't build serial.o unconditionally
MIPS: Replace deprecated CPU-hotplug functions.
MIPS: Alchemy: Fix spelling contraction "cant" -> "can't"
...
Here is the big set of char/misc driver changes for 5.15-rc1.
Lots of different driver subsystems are being updated in here, notably:
- mhi subsystem update
- fpga subsystem update
- coresight/hwtracing subsystem update
- interconnect subsystem update
- nvmem subsystem update
- parport drivers update
- phy subsystem update
- soundwire subsystem update
and there are some other char/misc drivers being updated as well:
- binder driver additions
- new misc drivers
- lkdtm driver updates
- mei driver updates
- sram driver updates
- other minor driver updates.
Note, there are no habanna labs driver updates in this pull request,
that will probably come later before -rc1 is out in a different request.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYS+Kyw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymlpACg0JM+hSeo8T5GtwZksZ1QXXQfh8sAoK6Dt6xF
e62OQuuMFT0Un0qOflZk
=emH+
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver updates from Greg KH:
"Here is the big set of char/misc driver changes for 5.15-rc1.
Lots of different driver subsystems are being updated in here,
notably:
- mhi subsystem update
- fpga subsystem update
- coresight/hwtracing subsystem update
- interconnect subsystem update
- nvmem subsystem update
- parport drivers update
- phy subsystem update
- soundwire subsystem update
and there are some other char/misc drivers being updated as well:
- binder driver additions
- new misc drivers
- lkdtm driver updates
- mei driver updates
- sram driver updates
- other minor driver updates.
Note, there are no habanalabs driver updates in this pull request,
that will probably come later before -rc1 is out in a different
request.
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (169 commits)
Revert "bus: mhi: Add inbound buffers allocation flag"
misc/pvpanic: fix set driver data
VMCI: fix NULL pointer dereference when unmapping queue pair
char: mware: fix returnvar.cocci warnings
parport: remove non-zero check on count
soundwire: cadence: do not extend reset delay
soundwire: intel: conditionally exit clock stop mode on system suspend
soundwire: intel: skip suspend/resume/wake when link was not started
soundwire: intel: fix potential race condition during power down
phy: qcom-qmp: Add support for SM6115 UFS phy
dt-bindings: phy: qcom,qmp: Add SM6115 UFS PHY bindings
phy: qmp: Provide unique clock names for DP clocks
lkdtm: remove IDE_CORE_CP crashpoint
lkdtm: replace SCSI_DISPATCH_CMD with SCSI_QUEUE_RQ
coresight: Replace deprecated CPU-hotplug functions.
Documentation: coresight: Add documentation for CoreSight config
coresight: syscfg: Add initial configfs support
coresight: config: Add preloaded configurations
coresight: etm4x: Add complex configuration handlers to etmv4
coresight: etm-perf: Update to activate selected configuration
...
Armada 3700 does not support RXAUI, XFI and neither SFI. Remove unused
macros for these unsupported modes.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 9695375a3f ("phy: add A3700 COMPHY support")
Signed-off-by: David S. Miller <davem@davemloft.net>
Comphy phy mode 0x3 is incorrectly named. It is not SGMII but rather
2500Base-X mode which runs at 3.125 Gbps speed.
Rename macro names and comments to 2500Base-X.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 9695375a3f ("phy: add A3700 COMPHY support")
Signed-off-by: David S. Miller <davem@davemloft.net>
Comphy phy mode 0x3 is incorrectly named. It is not SGMII but rather
2500Base-X mode which runs at 3.125 Gbps speed.
Rename macro names and comments to 2500Base-X.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: eb6a1fcb53 ("phy: mvebu-cp110-comphy: Add SMC call support")
Fixes: c2afb2fef5 ("phy: mvebu-cp110-comphy: Rename the macro handling only Ethernet modes")
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the tables and constants for init sequences for UFS QMP phy found in
SM4250/6115 SoC. The phy is a variation of the v2 phy, but is mistakenly
labeled as v3-660 in downstream sources.
QSERDES COM, RX, TX registers match fully existing v2 registers, with
a few additions. PCS registers don't have much in common, but there are
no clashes with existing ones so new registers were added to existing v2
PCS pack.
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Link: https://lore.kernel.org/r/20210821155657.893165-3-iskren.chernev@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The USB/DP combo PHY exposes the "qmp_dp_phy_pll_link_clk" and
"qmp_dp_phy_pll_vco_div_clk" clocks, that are consumed by the display
clock controller. But for boards with multiple enabled QMP USB/DP combo
instances the hard coded names collides - and hence only the first
probed device is allowed to register.
Given that clocks are no longer reference globally by name and it's
possible to replace the hard coded names by something unique, but still
user friendly.
The two new clock names are based on dev_name() and results in names
such as "88ee000.phy::link_clk" and "88ee000.phy::vco_div_clk".
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210722030738.3385821-1-bjorn.andersson@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
PHY initialization for USB is required on linux boot or when
gt lane is changed from the current one and it is applicable
on PLL lock too.
Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
Link: https://lore.kernel.org/r/20210818084311.2643986-1-piyush.mehta@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
devm_phy_create can return -EPROBE_DEFER if the vbus-supply is not ready
yet. Silence this warning as the driver framework will re-attempt
registering the PHY. Use dev_err_probe() for phy resources to indicate
the deferral reason when waiting for the resource to come up.
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Link: https://lore.kernel.org/r/20210817041548.1276-7-linux.amoon@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Power off the PHY by putting it into reset mode.
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Link: https://lore.kernel.org/r/20210817041548.1276-6-linux.amoon@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
PIPE PHY status is used to communicate the completion of several PHY
functions. Check if PHY is ready for operation while configured for
PIPE mode during startup.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Link: https://lore.kernel.org/r/20210728145454.15945-10-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add debug information in probe regarding PHY configuration parameters
like single link or multilink protocol along with number of lanes
used for each protocol link.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Link: https://lore.kernel.org/r/20210728145454.15945-9-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Torrent PHY driver currently supports single link DP configuration.
Prepare driver to support multilink DP configurations by adding
separate functions for common initialization sequence.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210728145454.15945-8-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add PHY registers for single link DP in array format to simplify
code and to improve readability. This supports already supported
frequencies for DP of 19.2MHz and 25MHz.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Link: https://lore.kernel.org/r/20210728145454.15945-6-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Torrent PHY supports multiple serdes standards with different input
reference clock frequencies. PHY register values differ based on the
reference clock rate. Add PHY input reference clock frequency as a
new dimension to select proper register configuration. No functional
change is intended.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Link: https://lore.kernel.org/r/20210728145454.15945-5-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Torrent PHY supports different input reference clock frequencies.
Register configurations will be different based on reference clock value.
Prepare driver to support such multiple reference clock frequencies.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210728145454.15945-4-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
So it will be avilable for generic MIPS kernel.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This patch adds USB2.0 PHY support for RZ/G2L SoC.
We need to use a different compatible string due to some differences
with R-Car Gen3 USB2.0 PHY. It uses line ctrl register for OTG_ID
pin changes and different OTG-BC interrupt bit for device recognition.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> # on R-Car
Link: https://lore.kernel.org/r/20210727185527.19907-4-biju.das.jz@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Since commit 88d26136a2 ("PM: Prevent runtime suspend during system
resume"), PM runtime will not let devices idle during system suspend.
This is because of the pm_runtime_get_noresume() call done in
device_prepare() that is not released until at device_complete() after
resume.
We must now disable the USB PHY in suspend if no USB cable is connected.
Cc: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210727104512.52968-1-tony@atomide.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The controller is designed to use use PLL integer mode, but
in fact used fractional mode for some ones on mt8195, this
causes signal degradation (e.g. eye diagram test fail), fix
it by switching PLL to 26Mhz from default 48Mhz to improve
signal quality.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1627028562-23584-3-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The PHYA arch is updated, and doesn't support slew rate calibrate
anymore on 7nm or advanced process, add a new version number to
support it.
Note: the FreqMeter bank is not used but reserved.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1627028562-23584-2-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix errant use of "/**" to begin a comment although the comment
is not kernel-doc notation. Just use "/*" instead.
Fixes this kernel-doc warning:
drivers/phy/qualcomm/phy-qcom-usb-hs.c:3: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Copyright (C) 2016 Linaro Ltd
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: linux-phy@lists.infradead.org
Link: https://lore.kernel.org/r/20210723022548.25695-1-rdunlap@infradead.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For_each_available_child_of_node should have of_node_put()
before break around line 1184. The other jumps out of the
loop do contain the put.
Generated by: scripts/coccinelle/iterators/for_each_child.cocci
CC: Sumera Priyadarsini <sylphrenadin@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: kernel test robot <lkp@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@inria.fr>
Link: https://lore.kernel.org/r/alpine.DEB.2.22.394.2106231617540.99238@hadrien
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When these are not referenced, gcc prints a harmless warning:
drivers/phy/tegra/xusb.c:1286:12: error: 'tegra_xusb_padctl_resume_noirq' defined but not used [-Werror=unused-function]
1286 | static int tegra_xusb_padctl_resume_noirq(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/phy/tegra/xusb.c:1276:12: error: 'tegra_xusb_padctl_suspend_noirq' defined but not used [-Werror=unused-function]
1276 | static int tegra_xusb_padctl_suspend_noirq(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: c545a90567 ("phy: tegra: xusb: Add sleepwalk and suspend/resume")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210721152550.2976003-1-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
A copy paste error was snuck into the patch going upstream that made the
SC8180x PCIe PHY use the SM8250 serdes table, but while this works
there's some differences in the tables (and the SC8180x was left
dangling). So correct the SC8180x definition to use the SC8180x serdes
table.
Fixes: f839f14e24 ("phy: qcom-qmp: Add sc8180x PCIe support")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210721163029.2813497-1-bjorn.andersson@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch adds to support phy-exynosautov9-ufs driver for ExynosAuto v9
series SoCs. The patch adds "samsung,exynosautov9-ufs-phy" compatible.
Unlike previous exynos ufs phy, the chip uses 0x50 offset as
PHY_TRSV_REG_CFG_OFFSET.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210709094524.110193-3-chanho61.park@samsung.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Instead of using exynos7 ufs definition in phy-exynos7-ufs.h, we should
put it into phy-exynos7-ufs.c to be included different objects or units.
Suggested-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210709094524.110193-2-chanho61.park@samsung.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Qualcomm SC8180x platform has 4 PCIe controllers and PHYs, typically
used to connect things such as a modem or NVME storage device. Add the
programming sequence to get the PHYs up and running.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210629004509.1788286-2-bjorn.andersson@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Here is the big set of USB and Thunderbolt patches for 5.14-rc1.
Nothing major here just lots of little changes for new hardware and
features. Highlights are:
- more USB 4 support added to the thunderbolt core
- build warning fixes all over the place
- usb-serial driver updates and new device support
- mtu3 driver updates
- gadget driver updates
- dwc3 driver updates
- dwc2 driver updates
- isp1760 host driver updates
- musb driver updates
- lots of other tiny things.
Full details are in the shortlog.
All of these have been in linux-next for a while now with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM3EA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynGewCeMg7YvtCnqFBNebC+GfKpFTgWxO4AnAppjSrZ
RPGQgfZdWmx7daCXWbSK
=u68a
-----END PGP SIGNATURE-----
Merge tag 'usb-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt patches for 5.14-rc1.
Nothing major here just lots of little changes for new hardware and
features. Highlights are:
- more USB 4 support added to the thunderbolt core
- build warning fixes all over the place
- usb-serial driver updates and new device support
- mtu3 driver updates
- gadget driver updates
- dwc3 driver updates
- dwc2 driver updates
- isp1760 host driver updates
- musb driver updates
- lots of other tiny things.
Full details are in the shortlog.
All of these have been in linux-next for a while now with no reported
issues"
* tag 'usb-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (223 commits)
phy: qcom-qusb2: Add configuration for SM4250 and SM6115
dt-bindings: phy: qcom,qusb2: document sm4250/6115 compatible
dt-bindings: usb: qcom,dwc3: Add bindings for sm6115/4250
USB: cdc-acm: blacklist Heimann USB Appset device
usb: xhci-mtk: allow multiple Start-Split in a microframe
usb: ftdi-elan: remove redundant continue statement in a while-loop
usb: class: cdc-wdm: return the correct errno code
xhci: remove redundant continue statement
usb: dwc3: Fix debugfs creation flow
usb: gadget: hid: fix error return code in hid_bind()
usb: gadget: eem: fix echo command packet response issue
usb: gadget: f_hid: fix endianness issue with descriptors
Revert "USB: misc: Add onboard_usb_hub driver"
Revert "of/platform: Add stubs for of_platform_device_create/destroy()"
Revert "usb: host: xhci-plat: Create platform device for onboard hubs in probe()"
Revert "arm64: dts: qcom: sc7180-trogdor: Add nodes for onboard USB hub"
xhci: solve a double free problem while doing s4
xhci: handle failed buffer copy to URB sg list and fix a W=1 copiler warning
xhci: Add adaptive interrupt rate for isoch TRBs with XHCI_AVOID_BEI quirk
xhci: Remove unused defines for ERST_SIZE and ERST_ENTRIES
...
Here is the big set of IIO and staging driver patches for 5.14-rc1.
Loads of IIO driver updates and additions in here, the shortlog has the
full details.
For the staging side, we moved a few drivers out of staging, and deleted
the kpc2000 drivers as the original developer asked us to because no one
was working on them anymore.
Also in here are loads of coding style cleanups due to different intern
projects focusing on the staging tree to try to get experience doing
kernel development.
All of these have been in the linux-next tree for a while with no
reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM50w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykZ4wCeK/JreZijlAy0O5Gq1equvRx1jJoAoJmmt7UY
bx6qpcmUM7c53cMXr/kh
=6suo
-----END PGP SIGNATURE-----
Merge tag 'staging-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging / IIO driver updates from Greg KH:
"Here is the big set of IIO and staging driver patches for 5.14-rc1.
Loads of IIO driver updates and additions in here, the shortlog has
the full details.
For the staging side, we moved a few drivers out of staging, and
deleted the kpc2000 drivers as the original developer asked us to
because no one was working on them anymore.
Also in here are loads of coding style cleanups due to different
intern projects focusing on the staging tree to try to get experience
doing kernel development.
All of these have been in the linux-next tree for a while with no
reported problems"
* tag 'staging-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (744 commits)
staging: hi6421-spmi-pmic: cleanup some macros
staging: hi6421-spmi-pmic: change identation of a table
staging: hi6421-spmi-pmic: change a return code
staging: hi6421-spmi-pmic: better name IRQs
staging: hi6421-spmi-pmic: use devm_request_threaded_irq()
staging: hisilicon,hi6421-spmi-pmic.yaml: cleanup descriptions
spmi: hisi-spmi-controller: move driver from staging
phy: phy-hi3670-usb3: move driver from staging into phy
staging: rtl8188eu: remove include/rtw_debug.h header
staging: rtl8188eu: remove GlobalDebugLevel variable
staging: rtl8188eu: remove DRIVER_PREFIX preprocessor definition
staging: rtl8188eu: remove RT_TRACE macro
staging: rtl8188eu: remove all RT_TRACE calls from hal/rtl8188eu_recv.c
staging: rtl8188eu: remove all RT_TRACE calls from hal/hal_intf.c
staging: rtl8188eu: remove all RT_TRACE calls from hal/rtl8188eu_xmit.c
staging: rtl8188eu: remove all RT_TRACE calls from core/rtw_xmit.c
staging: rtl8188eu: remove all RT_TRACE calls from core/rtw_pwrctrl.c
staging: rtl8188eu: remove all RT_TRACE calls from core/rtw_recv.c
staging: rtl8188eu: remove all RT_TRACE calls from core/rtw_ioctl_set.c
staging: rtl8188eu: remove all RT_TRACE calls from core/rtw_ieee80211.c
...
Here is the big set of char / misc and other driver subsystem updates
for 5.14-rc1. Included in here are:
- habanna driver updates
- fsl-mc driver updates
- comedi driver updates
- fpga driver updates
- extcon driver updates
- interconnect driver updates
- mei driver updates
- nvmem driver updates
- phy driver updates
- pnp driver updates
- soundwire driver updates
- lots of other tiny driver updates for char and misc drivers
This is looking more and more like the "various driver subsystems mushed
together" tree...
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM8jQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymECgCg0yL+8WxDKO5Gg5llM5PshvLB1rQAn0y5pDgg
nw78LV3HQ0U7qaZBtI91
=x+AR
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver updates from Greg KH:
"Here is the big set of char / misc and other driver subsystem updates
for 5.14-rc1. Included in here are:
- habanalabs driver updates
- fsl-mc driver updates
- comedi driver updates
- fpga driver updates
- extcon driver updates
- interconnect driver updates
- mei driver updates
- nvmem driver updates
- phy driver updates
- pnp driver updates
- soundwire driver updates
- lots of other tiny driver updates for char and misc drivers
This is looking more and more like the "various driver subsystems
mushed together" tree...
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (292 commits)
mcb: Use DEFINE_RES_MEM() helper macro and fix the end address
PNP: moved EXPORT_SYMBOL so that it immediately followed its function/variable
bus: mhi: pci-generic: Add missing 'pci_disable_pcie_error_reporting()' calls
bus: mhi: Wait for M2 state during system resume
bus: mhi: core: Fix power down latency
intel_th: Wait until port is in reset before programming it
intel_th: msu: Make contiguous buffers uncached
intel_th: Remove an unused exit point from intel_th_remove()
stm class: Spelling fix
nitro_enclaves: Set Bus Master for the NE PCI device
misc: ibmasm: Modify matricies to matrices
misc: vmw_vmci: return the correct errno code
siox: Simplify error handling via dev_err_probe()
fpga: machxo2-spi: Address warning about unused variable
lkdtm/heap: Add init_on_alloc tests
selftests/lkdtm: Enable various testable CONFIGs
lkdtm: Add CONFIG hints in errors where possible
lkdtm: Enable DOUBLE_FAULT on all architectures
lkdtm/heap: Add vmalloc linear overflow test
lkdtm/bugs: XFAIL UNALIGNED_LOAD_STORE_WRITE
...
Since the EMMC clock was changed from 200Mhz to 175Mhz in FIP,
there were some warnings introduced, as the frequency values
being checked was still wrt 200Mhz in code. Hence, the frequency
checks are now updated based on the current 175Mhz EMMC clock changed
in FIP.
Spamming kernel log msg:
"phy phy-20290000.mmc_phy.2: Unsupported rate: 43750000"
Signed-off-by: Rashmi A <rashmi.a@intel.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210603182242.25733-3-rashmi.a@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The phy USB3 driver for Hisilicon 970 (hi3670) is ready
for mainstream. Mode it from staging into the main driver's
phy/ directory.
Acked-by: Rob Herring <robh@kernel.org>
Acked-By: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/dcf66a01aaeaab93cda52f9a283ecbdf9fa71bb8.1624606660.git.mchehab+huawei@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SM4250 and SM6115 uses the same register layout as MSM8996, but the
tune sequence is a bit different.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Link: https://lore.kernel.org/r/20210622203240.559979-4-iskren.chernev@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Updates:
- Yaml conversion for renesas,rcar-gen3 pcie phy and
rockchip-usb-phy bindings
- Support for devm_phy_get() taking NULL phy name
- New support:
- PCIe phy for Qualcomm IPQ60xx
- PCIe phy for Qualcomm SDX55
- USB phy for RK3308
- CAN transceivers phy for TI TCAN104x
- Innosilicon-based CSI dphy for rockchip
-----BEGIN PGP SIGNATURE-----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=Col+
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.14_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy into char-misc-next
Vinod writes:
phy-for-5.14 version 2
- Updates:
- Yaml conversion for renesas,rcar-gen3 pcie phy and
rockchip-usb-phy bindings
- Support for devm_phy_get() taking NULL phy name
- New support:
- PCIe phy for Qualcomm IPQ60xx
- PCIe phy for Qualcomm SDX55
- USB phy for RK3308
- CAN transceivers phy for TI TCAN104x
- Innosilicon-based CSI dphy for rockchip
* tag 'phy-for-5.14_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (36 commits)
phy: Revert "phy: ralink: Kconfig: convert mt7621-pci-phy into 'bool'"
phy: ti: dm816x: Fix the error handling path in 'dm816x_usb_phy_probe()
phy: uniphier-pcie: Fix updating phy parameters
phy/rockchip: add Innosilicon-based CSI dphy
dt-bindings: phy: add yaml binding for rockchip-inno-csi-dphy
phy: rockchip: remove redundant initialization of pointer cfg
phy: phy-can-transceiver: Add support for generic CAN transceiver driver
dt-bindings: phy: Add binding for TI TCAN104x CAN transceivers
phy: core: Reword the comment specifying the units of max_link_rate to be Mbps
phy: phy-mtk-hdmi: Remove redundant dev_err call in mtk_hdmi_phy_probe()
phy: phy-mtk-mipi-dsi: Remove redundant dev_err call in mtk_mipi_tx_probe()
phy: phy-mmp3-hsic: Remove redundant dev_err call in mmp3_hsic_phy_probe()
phy: bcm-ns-usb3: Remove redundant dev_err call in bcm_ns_usb3_mdio_probe()
MAINTAINERS: update marvell,armada-3700-utmi-phy.yaml reference
phy: phy-twl4030-usb: use DEVICE_ATTR_RO macro
dt-bindings: phy: convert rockchip-usb-phy.txt to YAML
phy: phy-rockchip-inno-usb2: add support for RK3308 USB phy
dt-bindings: phy: rockchip-inno-usb2: add compatible for rk3308 USB phy
phy: stm32: manage optional vbus regulator on phy_power_on/off
dt-bindings: phy: add vbus-supply optional property to phy-stm32-usbphyc
...
This reverts commit 6eded551ce ("phy: ralink: Kconfig: convert
mt7621-pci-phy into 'bool'") as we don't want drivers to be built in and
should be a module instead
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The current driver uses a value from register TEST_O as the original
value for register TEST_I, though, the value is overwritten by "param",
so there is a bug that the original value isn't no longer used.
The value of TEST_O[7:0] should be masked with "mask", replaced with
"param", and placed in the bitfield TESTI_DAT_MASK as new TEST_I value.
Fixes: c6d9b13241 ("phy: socionext: add PCIe PHY driver support")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1623037842-19363-1-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The CSI dphy found for example on the rk3326/px30 and rk3368 is based
on an IP design from Innosilicon. Add a driver for it.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Link: https://lore.kernel.org/r/20210610212935.3520341-3-heiko@sntech.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The pointer cfg is being initialized with a value that is never read and
it is being updated later with a new value. The initialization is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210609113901.185230-1-colin.king@canonical.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver adds support for generic CAN transceivers. Currently
the modes supported by this driver are standby and normal modes for TI
TCAN1042 and TCAN1043 CAN transceivers.
The transceiver is modelled as a phy with pins controlled by gpios, to put
the transceiver in various device functional modes. It also gets the phy
attribute max_link_rate for the usage of CAN drivers.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20210510051006.11393-4-a-govindraju@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: He Ying <heying24@huawei.com>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20210408115530.15673-1-heying24@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: He Ying <heying24@huawei.com>
Link: https://lore.kernel.org/r/20210408114850.14422-1-heying24@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: He Ying <heying24@huawei.com>
Link: https://lore.kernel.org/r/20210408090806.247325-1-heying24@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: He Ying <heying24@huawei.com>
Link: https://lore.kernel.org/r/20210408090808.247368-1-heying24@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
To support XUSB host controller ELPG, this commit moves VBUS control
.phy_power_on()/.phy_power_off() to .phy_init()/.phy_exit().
When XUSB host controller enters ELPG, host driver invokes
.phy_power_off(), VBUS should remain ON so that USB devices will not
disconnect. VBUS can be turned OFF when host driver invokes
.phy_exit() which indicates disabling a USB port.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit implements Tegra210 XUSB PADCTL wake and sleepwalk
routines. Sleepwalk logic is in PMC (always-on) hardware block.
PMC driver provides managed access to the sleepwalk registers
via regmap framework.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit adds sleepwalk/wake and suspend/resume interfaces
to Tegra XUSB PHY driver.
Tegra XUSB host controller driver makes use of sleepwalk functions
to enable/disable sleepwalk circuit which is in always-on partition
and can respond to USB resume signals when controller is not powered.
Sleepwalk can be enabled/disabled for any USB UPHY individually.
- tegra_xusb_padctl_enable_phy_sleepwalk()
- tegra_xusb_padctl_disable_phy_sleepwalk()
Tegra XUSB host controller driver makes use of wake functions to
enable/disable/query wake circuit which is in always-on partition
can wake system up when USB resume happens.
Wake circuit can be enabled/disabled for any USB PHY individually.
- tegra_xusb_padctl_enable_phy_wake()
- tegra_xusb_padctl_disable_phy_wake()
- tegra_xusb_padctl_remote_wake_detected()
This commit also adds two system suspend stubs that can be used to
save and restore XUSB PADCTL context during system suspend and
resume.
- tegra_xusb_padctl_suspend_noirq()
- tegra_xusb_padctl_resume_noirq()
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
As per Tegra210 TRM, before changing lane assignments, driver should
keep lanes in IDDQ and sleep state; after changing lane assignments,
driver should bring lanes out of IDDQ.
This commit implements the required operations.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit is a preparation for enabling XUSB SC7 support.
It rearranges Tegra210 XUSB PADCTL UPHY initialization sequence,
for the following reasons:
1. PLLE hardware power sequencer has to be enabled only after both
PEX UPHY PLL and SATA UPHY PLL are initialized.
tegra210_uphy_init() -> tegra210_pex_uphy_enable()
-> tegra210_sata_uphy_enable()
-> tegra210_plle_hw_sequence_start()
-> tegra210_aux_mux_lp0_clamp_disable()
2. At cold boot and SC7 exit, the following bits must be cleared after
PEX/SATA lanes are out of IDDQ (IDDQ_DISABLE=1).
a. XUSB_PADCTL_ELPG_PROGRAM1_AUX_MUX_LP0_CLAMP_EN,
b. XUSB_PADCTL_ELPG_PROGRAM1_AUX_MUX_LP0_CLAMP_EN_EARLY
c. XUSB_PADCTL_ELPG_PROGRAM1_AUX_MUX_LP0_VCORE_DOWN
tegra210_pex_uphy_enable() and tegra210_sata_uphy_enable() are in
charge of bringing lanes out of IDDQ, and then AUX_MUX_LP0_* bits
will be cleared by tegra210_aux_mux_lp0_clamp_disable().
3. Once UPHY PLL hardware power sequencer is enabled, do not assert
reset to PEX/SATA PLLs, otherwise UPHY PLL operation will be broken.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The programming sequence in tegra210_usb3_port_enable() is required
for both cold boot and SC7 exit, and must be performed only after
PEX/SATA UPHY is initialized. Therefore, this commit moves the
programming sequence to tegra210_usb3_phy_power_on(). PCIE/SATA phy
.power_on() stub will invoke tegra210_usb3_phy_power_on() if the lane
is assigned for XUSB super-speed.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The of_device_id is included unconditionally by of.h header and used
in the driver as well. Remove of_match_ptr to fix W=1 compile test
warning with !CONFIG_OF:
drivers/phy/ralink/phy-mt7621-pci.c:341:34: warning: unused variable 'mt7621_pci_phy_ids' [-Wunused-const-variable]
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210603043219.32646-1-sergio.paracuellos@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When the code execute this if statement, the value of ret is 0.
However, we can see from the dev_err() log that the value of
ret should be -EINVAL.
Clean up smatch warning:
drivers/phy/ti/phy-j721e-wiz.c:1216 wiz_probe() warn: missing error code 'ret'
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Fixes: c9f9eba066 ("phy: ti: j721e-wiz: Manage typec-gpio-dir")
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/1621939832-65535-1-git-send-email-yang.lee@linux.alibaba.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use DEVICE_ATTR_RO helper instead of plain DEVICE_ATTR,
which makes the code a bit shorter and easier to read.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20210520135132.37628-1-yuehaibing@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The RK3308 SoC uses a slightly different USB phy than other Rockchip
parts.
This commit adds support for that phy.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Link: https://lore.kernel.org/r/20210514150044.2099298-3-t.schramm@manjaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch adds support for optional vbus regulator.
It is managed on phy_power_on/off calls and may be needed for host mode.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20210517120821.26466-3-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
A * has been added at the starting of new line
The closing */ of multi line comment shifted to new line
This is done to maintain code uniformity.
Signed-off-by: Shubhankar Kuranagatti <shubhankarvk@gmail.com>
Link: https://lore.kernel.org/r/20210428165515.o47o5awzdxirxkqi@kewl-virtual-machine
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use clk_disable_unprepare() in the error path of mtk_phy_init() to fix
some resource leaks.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1621420659-15858-1-git-send-email-yangtiezhu@loongson.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: a43f72ae13 ("phy: cadence: Sierra: Change MAX_LANES of Sierra to 16")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Wensheng <wangwensheng4@huawei.com>
Link: https://lore.kernel.org/r/20210517015749.127799-1-wangwensheng4@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The PCIe PHY version used in SDX55 is v4.20 which has different register
offsets compared to the v4.0x PHYs. So separate register defines are
used for init sequence and PHY status.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210427065400.18958-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation of the support for v4.20 PCIe PHY in SDX55, use a
separate "phy_status" field for the status bit offset. This is needed
because, the v4.20 PHY uses a different offset for the PHY Status.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210427065400.18958-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The rest of the code refers to version 1.2 of the MIPI D-PHY
specification. But this comment refers to 2.1, while a sub comment of
the function refers to 1.2 again. Replace 2.1 with 1.2.
Signed-off-by: Sebastian Fricke <sebastian.fricke@posteo.net>
Link: https://lore.kernel.org/r/20210421041740.8451-1-sebastian.fricke@posteo.net
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For a single PHY, there's no reason to have a phy-names entry in DT.
The DT specific get functions allow for this already, but devm_phy_get()
WARNs in this case. Other subsystems also don't warn in their get
functions. Let's drop the WARN for DT case in devm_phy_get().
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210414135525.3535787-1-robh@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
While IS_ENABLED() is perfectly fine for CONFIG_* symbols, it is not
for other symbols such as __BIG_ENDIAN that is provided directly by
the compiler.
Switch to use CONFIG_CPU_BIG_ENDIAN instead of __BIG_ENDIAN.
Signed-off-by: Chen Li <chenli@uniontech.com>
Reviewed-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes: 94583a4104 ("phy: usb: Restructure in preparation for adding 7216 USB support")
Link: https://lore.kernel.org/r/87czuggpra.wl-chenli@uniontech.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The way of printing the pointer address for the 'port_base'
address got into compile warnings on some architectures
[-Wpointer-to-int-cast]. Instead of use '%08x' and cast
to an 'unsigned int' just make use of '%px' and avoid the
cast. To avoid not really needed driver verbosity on normal
behaviour change also from 'dev_info' to 'dev_dbg'.
Fixes: d87da32372 ("phy: ralink: Add PHY driver for MT7621 PCIe PHY")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210508070930.5290-7-sergio.paracuellos@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Rafał Miłecki
Stephan Gerhold
Hans de Goede
Liu Ying
Al Cooper
Minghao Chi (CGEL ZTE)
Samuel Holland
Andre Przywara
Yifeng Zhao
Sankeerth Billakanti
Aswath Govindraju
Vinod Koul
Wan Jiabing
Amjad Ouled-Ameur
Geert Uytterhoeven
Dan Carpenter
Luca Weiss
Marcel Ziswiler
Robert Hancock
Ansuel Smith
Kishon Vijay Abraham I
Linus Torvalds
Greg Kroah-Hartman
Swapnil Jakhade
Miaoqian Lin
Ryuta NAKANISHI
Chunfeng Yun
Dmitry Baryshkov
Peter Geis
Jakub Kicinski
Richard Zhu
Colin Ian King
Horatiu Vultur
Guo Zhengkui
Zou Wei
Fabrice Gasnier
Marek Behún
Rashmi A
Yang Guang
Kunihiko Hayashi
Martin Blumenstingl
Bjorn Andersson
Randy Dunlap
Amelie Delaunay
Yang Yingliang
Sandeep Maheswaram
Vladimir Zapolskiy
Shawn Guo
Sean Anderson
Cai Huoqing
Mauro Carvalho Chehab
Krzysztof Kozlowski
Daniel Lezcano
Pali Rohár
Iskren Chernev
Piyush Mehta
Anand Moon
Jiaxun Yang
Baruch Siach
Biju Das
Tony Lindgren
kernel test robot
Arnd Bergmann
Chanho Park
Christophe JAILLET
Heiko Stuebner
Colin Ian King
He Ying
JC Kuo
Sergio Paracuellos
Yang Li
YueHaibing
Tobias Schramm
Shubhankar Kuranagatti
Tiezhu Yang
Wang Wensheng
Manivannan Sadhasivam
Sebastian Fricke
Rob Herring
Chen Li
Selvam Sathappan Periakaruppan