HT irqs vectors are 8 groups, each group has 32 irqs, Loongson64C CPUs
can use only 4 groups and Loongson64G CPUs can use all 8 groups. So the
number of msi vectors of Loongson64G is 192 (32*8 - 64 = 192).
Fixes: 24af105962 ("MIPS: Loongson64: DeviceTree for LS7A PCH")
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Although currently we're not enabling any ISA device in devicetree,
but this node is required to express the ranges of address reserved
for ISA.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Ranges should express the actual physical address on bus.
Also enlarge the PCI I/O size to the actual hardware limit.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The ROUT (right channel output of audio codec) was connected to INL
(left channel of audio amplifier) instead of INR (right channel of audio
amplifier).
Fixes: 8ddebad15e ("MIPS: qi_lb60: Migrate to devicetree")
Cc: stable@vger.kernel.org # v5.3
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add a devicetree node for the Image Processing Unit (IPU) found in the
JZ4725B. Connect it with graph nodes to the LCD node. The LCD driver
will expect the IPU node to be accessed through graph port #8, as stated
in the bindings documentation.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
1.The CU1000-Neo board actually uses X1000E instead of X1000,
so the wrongly written "ingenic,x1000" in compatible should
be changed to "ingenic,x1000e".
2.Adjust the order of nodes according to the corresponding
address value.
3.Drop unnecessary node in "wlan_pwrseq".
4.Add the leds node to "cu1000-neo.dts".
Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add a device tree and a defconfig for the Ingenic X1830 based
YSH & ATIL CU Neo board.
Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Support the Ingenic X1830 SoC using the code under arch/mips/jz4740.
This is left unselectable in Kconfig until a X1830 based board is
added in a later commit.
Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
From previous commits, the machine names with "loongson3-" prefix have
renamed to "loongson64c-" prefix in documents, but the .dts files have
not been updated as well. So fix it.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Tested-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The RS-90, better known as RetroMini, is a small and pocketable handheld
gaming console from YLMChina. It has little more than a JZ4725B SoC, a
NAND, a screen, some buttons and a speaker.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add preliminary support for boards based on the JZ4725B SoC from
Ingenic.
The JZ4725B SoC is supposed to be older than the JZ4740 SoC, but its
internals are much closer to what can be found on the JZ4750 and newer
SoCs.
It is low-power SoC with a MIPS32r1 SoC running at ~360 MHz, and no FPU.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The size of ioports in the current RS780E dts file is not enough, which
sometimes causes device initialize fail. So we increase the size of ISA/
LPC ioports to 0x4000, and increase the size of PCI ioports to 0x8000.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Loongson-3A R1/R2/R3 and Loongson-3B R1/R2 use the same package naming
in dts, and Loongson-3A R4 will be different. In cpu.h the classic 64bit
Loongson processors are called Loongson64C (C for classic, pre Loongson-
3A R4), and the new 64bit Loongson processors are called Loongson64G (G
for generic, Loongson-3A R4+). To keep consistency and make extensible,
we rename the classic "loongson3" prefix to "loongson64c", and the new
prefix for Loongson-3A R4+ will be "loongson64g".
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Previously marked as active high, but is in reality active low.
Cc: stable@vger.kernel.org
Fixes: b1bfdb6605 ("MIPS: ingenic: DTS: Update GCW0 support")
Signed-off-by: João H. Spies <jhlspies@gmail.com>
Tested-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This patch adds a description of the load/save GPIN pin, used in the
VSC8584 PHY for timestamping operations. The related pinctrl description
is also added.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_MIPS_MALTA is not set but CONFIG_LEGACY_BOARD_SEAD3 is set,
the subdir arch/mips/boot/dts/mti will not be built, so the sead3.dts
which depends on CONFIG_LEGACY_BOARD_SEAD3 in this subdir is also not
built, and then there exists the following build error, fix it.
LD .tmp_vmlinux.kallsyms1
arch/mips/generic/board-sead3.o:(.mips.machines.init+0x4): undefined reference to `__dtb_sead3_begin'
Makefile:1106: recipe for target 'vmlinux' failed
make: *** [vmlinux] Error 1
Additionally, add CONFIG_FIT_IMAGE_FDT_BOSTON check for subdir img to
fix the following build error when CONFIG_MACH_PISTACHIO is not set but
CONFIG_FIT_IMAGE_FDT_BOSTON is set.
FATAL ERROR: Couldn't open "boot/dts/img/boston.dtb": No such file or directory
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Fixes: 41528ba6af ("MIPS: DTS: Only build subdir of current platform")
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add support for the GCW Zero prototype. The only (?) difference is that
it only has 256 MiB of RAM, compared to the 512 MiB of RAM of the retail
device.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add memory info of the GCW Zero in its devicetree. The bootloader
generally provides this information, but since it is fixed to 512 MiB,
it doesn't hurt to have it in devicetree. It allows the kernel to boot
without any parameter passed as argument.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add PCI Host controller node for Loongson64 with RS780E PCH dts.
Note that PCI interrupts are probed via legacy way, as different
machine have different interrupt arrangement, we can't cover all
of them in dt.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add config check in Makefile to only build the subdir of current platform.
E.g. without this patch:
AR arch/mips/built-in.a
AR arch/mips/boot/dts/brcm/built-in.a
AR arch/mips/boot/dts/cavium-octeon/built-in.a
AR arch/mips/boot/dts/img/built-in.a
AR arch/mips/boot/dts/ingenic/built-in.a
AR arch/mips/boot/dts/lantiq/built-in.a
DTC arch/mips/boot/dts/loongson/loongson3_4core_rs780e.dtb
DTB arch/mips/boot/dts/loongson/loongson3_4core_rs780e.dtb.S
AS arch/mips/boot/dts/loongson/loongson3_4core_rs780e.dtb.o
DTC arch/mips/boot/dts/loongson/loongson3_8core_rs780e.dtb
DTB arch/mips/boot/dts/loongson/loongson3_8core_rs780e.dtb.S
AS arch/mips/boot/dts/loongson/loongson3_8core_rs780e.dtb.o
AR arch/mips/boot/dts/loongson/built-in.a
AR arch/mips/boot/dts/mscc/built-in.a
AR arch/mips/boot/dts/mti/built-in.a
AR arch/mips/boot/dts/netlogic/built-in.a
AR arch/mips/boot/dts/ni/built-in.a
AR arch/mips/boot/dts/pic32/built-in.a
AR arch/mips/boot/dts/qca/built-in.a
AR arch/mips/boot/dts/ralink/built-in.a
AR arch/mips/boot/dts/xilfpga/built-in.a
AR arch/mips/boot/dts/built-in.a
With this patch:
AR arch/mips/built-in.a
DTC arch/mips/boot/dts/loongson/loongson3_4core_rs780e.dtb
DTB arch/mips/boot/dts/loongson/loongson3_4core_rs780e.dtb.S
AS arch/mips/boot/dts/loongson/loongson3_4core_rs780e.dtb.o
DTC arch/mips/boot/dts/loongson/loongson3_8core_rs780e.dtb
DTB arch/mips/boot/dts/loongson/loongson3_8core_rs780e.dtb.S
AS arch/mips/boot/dts/loongson/loongson3_8core_rs780e.dtb.o
AR arch/mips/boot/dts/loongson/built-in.a
AR arch/mips/boot/dts/built-in.a
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
schema violation was detected by the dtbs_check
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Fit led nodes to the latest naming schema.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This is an add-on patch to the main SoC Sparx5 series
(Message-ID: <20200513125532.24585-1-lars.povlsen@microchip.com>).
This changes the miim pinctrl function name from "miim1" to "miim" due
to refactoring in the driver, obsoleting the instance number.
The change in the driver was to better fit new platforms, as the
instance number is redundant information. Specifically, support for
the Microchip Sparx5 SoC is being submitted, where this change became
necessary.
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
LLD failed to link vmlinux with 64bit load address for 32bit ELF
while bfd will strip 64bit address into 32bit silently.
To fix LLD build, we should truncate load address provided by platform
into 32bit for 32bit kernel.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/786
Link: https://sourceware.org/bugzilla/show_bug.cgi?id=25784
Reviewed-by: Fangrui Song <maskray@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add support for the face buttons, the ACT8600 PMUC, the LCD panel
with backlight, the rumble, internal/external SD readers, and other
things.
Note that the otg-phy node was dropped in the process as it was neither
useful nor used, and was inside a non-compliant board "bus".
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add support for the RTC, AIC, CODEC, MMC 0/1/2, ADC, GPU, LCD,
USB OTG, USB PHY controllers.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add the TCU nodes to the JZ4780, JZ4770 and JZ4740 devicetree files.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
If N fields of X cells should be provided, then that's what the
devicetree should represent, instead of having one single field of
(N*X) cells.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The driver requires two cells and not just one.
Since these nodes are both disabled as no hardware currently use them,
this fix does not really requires a Fixes: tag.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add ACPI Controller Node for RS780E PCH to fit newly added driver.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
There is a unique MAC address programmed into the eFuses
of the JZ4780 chip in the CI20 factory. By using this
for initializing the DM9000 Ethernet controller, every
CI20 board has an individual - but stable - MAC address
and DHCP can assign stable IP addresses.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This patch brings support for the JZ4780 efuse. Currently it only exposes
a read only access to the entire 8K bits efuse memory and the
ethernet mac address for the davicom dm9000 chip on the CI20 board.
It also changes the nemc ranges definition to give the driver
access to the efuse registers, which are in the middle of the
nemc reg range.
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Here are 3 SPDX patches for 5.7-rc1.
One fixes up the SPDX tag for a single driver, while the other two go
through the tree and add SPDX tags for all of the .gitignore files as
needed.
Nothing too complex, but you will get a merge conflict with your current
tree, that should be trivial to handle (one file modified by two things,
one file deleted.)
All 3 of these have been in linux-next for a while, with no reported
issues other than the merge conflict.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXodg5A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykySQCgy9YDrkz7nWq6v3Gohl6+lW/L+rMAnRM4uTZm
m5AuCzO3Azt9KBi7NL+L
=2Lm5
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull SPDX updates from Greg KH:
"Here are three SPDX patches for 5.7-rc1.
One fixes up the SPDX tag for a single driver, while the other two go
through the tree and add SPDX tags for all of the .gitignore files as
needed.
Nothing too complex, but you will get a merge conflict with your
current tree, that should be trivial to handle (one file modified by
two things, one file deleted.)
All three of these have been in linux-next for a while, with no
reported issues other than the merge conflict"
* tag 'spdx-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx:
ASoC: MT6660: make spdxcheck.py happy
.gitignore: add SPDX License Identifier
.gitignore: remove too obvious comments
* Fix issue where write_cached_data() fails but write() still returns success
* maps: sa1100-flash: Replace zero-length array with flexible-array member
* phram: Fix a double free issue in error path
* Convert fallthrough comments into statements
* MAINTAINERS: Add the IRC channel to the MTD related subsystems
Raw NAND core changes:
* Add support for manufacturer specific suspend/resume operation
* Add support for manufacturer specific lock/unlock operation
* Replace zero-length array with flexible-array member
* Fix a typo ("manufecturer")
* Ensure nand_soft_waitrdy wait period is enough
Raw NAND controller driver changes:
* Brcmnand:
- Add support for flash-edu for dma transfers (+ bindings)
* Cadence:
- Reinit completion before executing a new command
- Change bad block marker size
- Fix the calculation of the avaialble OOB size
- Get meta data size from registers
* Qualcom:
- Use dma_request_chan() instead dma_request_slave_channel()
- Release resources on failure within qcom_nandc_alloc()
* Allwinner:
- Use dma_request_chan() instead dma_request_slave_channel()
* Marvell:
- Use dma_request_chan() instead dma_request_slave_channel()
- Release DMA channel on error
* Freescale:
- Use dma_request_chan() instead dma_request_slave_channel()
* Macronix:
- Add support for Macronix NAND randomizer (+ bindings)
* Ams-delta:
- Rename structures and functions to gpio_nand*
- Make the driver custom I/O ready
- Drop useless local variable
- Support custom driver initialisation
- Add module device tables
- Handle more GPIO pins as optional
- Make read pulses optional
- Don't hardcode read/write pulse widths
- Push inversion handling to gpiolib
- Enable OF partition info support
- Drop board specific partition info
- Use struct gpio_nand_platdata
- Write protect device during probe
* Ingenic:
- Use devm_platform_ioremap_resource()
- Add dependency on MIPS || COMPILE_TEST
* Denali:
- Deassert write protect pin
* ST:
- Use dma_request_chan() instead dma_request_slave_channel()
Raw NAND chip driver changes:
* Toshiba:
- Support reading the number of bitflips for BENAND (Built-in ECC NAND)
* Macronix:
- Add support for deep power down mode
- Add support for block protection
SPI-NAND core changes:
* Do not erase the block before writing a bad block marker
* Explicitly use MTD_OPS_RAW to write the bad block marker to OOB
* Stop using spinand->oobbuf for buffering bad block markers
* Rework detect procedure for different READ_ID operation
SPI-NAND driver changes:
* Toshiba:
- Support for new Kioxia Serial NAND
- Rename function name to change suffix and prefix (8Gbit)
- Add comment about Kioxia ID
* Micron:
- Add new Micron SPI NAND devices with multiple dies
- Add M70A series Micron SPI NAND devices
- identify SPI NAND device with Continuous Read mode
- Add new Micron SPI NAND devices
- Describe the SPI NAND device MT29F2G01ABAGD
- Generalize the OOB layout structure and function names
SPI NOR core changes:
* Move all the manufacturer specific quirks/code out of the core,
to make the core logic more readable and thus ease maintenance.
* Move the SFDP logic out of the core, it provides a better
separation between the SFDP parsing and core logic.
* Trim what is exposed in spi-nor.h. The SPI NOR controllers drivers
must not be able to use structures that are meant just for the
SPI NOR core.
* Use the spi-mem direct mapping API to let advanced controllers
optimize the read/write operations when they support direct mapping.
* Add generic formula for the Status Register block protection
handling. It fixes some long standing locking limitations and eases
the addition of the 4bit block protection support.
* Add block protection support for flashes with 4 block protection
bits in the Status Register.
SPI NOR controller drivers changes:
* The mtk-quadspi driver is replaced by the new spi-mem spi-mtk-nor
driver.
* Merge tag 'mtk-mtd-spi-move' into spi-nor/next to avoid conflicts.
HyperBus changes:
* Print error msg when compatible is wrong or missing
* Move mapping of direct access window from core to individual drivers
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl6GEU8ACgkQJWrqGEe9
VoSQ8gf/WV1vfxfAlgKRQ6WGkdrI+EndmciKx/sqf9KfAu6uNLHx3qcxQeibqvgC
KmIgJbCLXhgCUBZQLqyjqHtO3zImgPI2WWWR/tkieNaT9NT5jrAunYZpiqkCkjVD
HjML4iVcLwDJoHPZWTTTsFWd2cDLA8nFVXJQeaGRgdsx3j3D9OSOnfLGTUGfcg2H
lC0BxA6JRO7tdZlErqzy9BXUasjO5C7rsRzqgTiGT4h/H2yhYmDQhMW+Kz86zWiB
XdZsZJ2qLlTKntQmzR+30vbolId3iZqsO9q0mVkqWd2UQn5TpmmzNqLoYA6ys8KK
lW/1E53E3/Pq0+5ejGbD5m4afff+nw==
=/p2x
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"MTD core changes:
- Fix issue where write_cached_data() fails but write() still returns
success
- maps: sa1100-flash: Replace zero-length array with flexible-array
member
- phram: Fix a double free issue in error path
- Convert fallthrough comments into statements
- MAINTAINERS: Add the IRC channel to the MTD related subsystems
Raw NAND core changes:
- Add support for manufacturer specific suspend/resume operation
- Add support for manufacturer specific lock/unlock operation
- Replace zero-length array with flexible-array member
- Fix a typo ("manufecturer")
- Ensure nand_soft_waitrdy wait period is enough
Raw NAND controller driver changes:
- Brcmnand:
* Add support for flash-edu for dma transfers (+ bindings)
- Cadence:
* Reinit completion before executing a new command
* Change bad block marker size
* Fix the calculation of the avaialble OOB size
* Get meta data size from registers
- Qualcom:
* Use dma_request_chan() instead dma_request_slave_channel()
* Release resources on failure within qcom_nandc_alloc()
- Allwinner:
* Use dma_request_chan() instead dma_request_slave_channel()
- Marvell:
* Use dma_request_chan() instead dma_request_slave_channel()
* Release DMA channel on error
- Freescale:
* Use dma_request_chan() instead dma_request_slave_channel()
- Macronix:
* Add support for Macronix NAND randomizer (+ bindings)
- Ams-delta:
* Rename structures and functions to gpio_nand*
* Make the driver custom I/O ready
* Drop useless local variable
* Support custom driver initialisation
* Add module device tables
* Handle more GPIO pins as optional
* Make read pulses optional
* Don't hardcode read/write pulse widths
* Push inversion handling to gpiolib
* Enable OF partition info support
* Drop board specific partition info
* Use struct gpio_nand_platdata
* Write protect device during probe
- Ingenic:
* Use devm_platform_ioremap_resource()
* Add dependency on MIPS || COMPILE_TEST
- Denali:
* Deassert write protect pin
- ST:
* Use dma_request_chan() instead dma_request_slave_channel()
Raw NAND chip driver changes:
- Toshiba:
* Support reading the number of bitflips for BENAND (Built-in ECC NAND)
- Macronix:
* Add support for deep power down mode
* Add support for block protection
SPI-NAND core changes:
- Do not erase the block before writing a bad block marker
- Explicitly use MTD_OPS_RAW to write the bad block marker to OOB
- Stop using spinand->oobbuf for buffering bad block markers
- Rework detect procedure for different READ_ID operation
SPI-NAND driver changes:
- Toshiba:
* Support for new Kioxia Serial NAND
* Rename function name to change suffix and prefix (8Gbit)
* Add comment about Kioxia ID
- Micron:
* Add new Micron SPI NAND devices with multiple dies
* Add M70A series Micron SPI NAND devices
* identify SPI NAND device with Continuous Read mode
* Add new Micron SPI NAND devices
* Describe the SPI NAND device MT29F2G01ABAGD
* Generalize the OOB layout structure and function names
SPI NOR core changes:
- Move all the manufacturer specific quirks/code out of the core, to
make the core logic more readable and thus ease maintenance.
- Move the SFDP logic out of the core, it provides a better
separation between the SFDP parsing and core logic.
- Trim what is exposed in spi-nor.h. The SPI NOR controllers drivers
must not be able to use structures that are meant just for the SPI
NOR core.
- Use the spi-mem direct mapping API to let advanced controllers
optimize the read/write operations when they support direct
mapping.
- Add generic formula for the Status Register block protection
handling. It fixes some long standing locking limitations and eases
the addition of the 4bit block protection support.
- Add block protection support for flashes with 4 block protection
bits in the Status Register.
SPI NOR controller drivers changes:
- The mtk-quadspi driver is replaced by the new spi-mem spi-mtk-nor
driver.
- Merge tag 'mtk-mtd-spi-move' into spi-nor/next to avoid conflicts.
HyperBus changes:
- Print error msg when compatible is wrong or missing
- Move mapping of direct access window from core to individual
drivers"
* tag 'mtd/for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (103 commits)
mtd: Convert fallthrough comments into statements
mtd: rawnand: toshiba: Support reading the number of bitflips for BENAND (Built-in ECC NAND)
MAINTAINERS: Add the IRC channel to the MTD related subsystems
mtd: Fix issue where write_cached_data() fails but write() still returns success
mtd: maps: sa1100-flash: Replace zero-length array with flexible-array member
mtd: phram: fix a double free issue in error path
mtd: spinand: toshiba: Support for new Kioxia Serial NAND
mtd: spinand: toshiba: Rename function name to change suffix and prefix (8Gbit)
mtd: rawnand: macronix: Add support for deep power down mode
mtd: rawnand: Add support for manufacturer specific suspend/resume operation
mtd: spi-nor: Enable locking for n25q512ax3/n25q512a
mtd: spi-nor: Add SR 4bit block protection support
mtd: spi-nor: Add generic formula for SR block protection handling
mtd: spi-nor: Set all BP bits to one when lock_len == mtd->size
mtd: spi-nor: controllers: aspeed-smc: Replace zero-length array with flexible-array member
mtd: spi-nor: Clear WEL bit when erase or program errors occur
MAINTAINERS: update entry after SPI NOR controller move
mtd: spi-nor: Trim what is exposed in spi-nor.h
mtd: spi-nor: Drop the MFR definitions
mtd: spi-nor: Get rid of the now empty spi_nor_ids[] table
...
Add generic device dts for Loongson-3 devices.
They are currently almost identical but will be different later.
Some PCH devices like PCI Host Bridge is still enabled by platform
code for now.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Co-developed-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
a) add DT node for SW1 as Enter button
The SW1 button can be used as a simple one-button keyboard
and is connected to PD17.
Note: SW1 has a second meaning to change the boot sequence
when pressed while powering on.
b) give eth0_power a defined voltage.
This is a 3.3V power switch (DVNET3.3V).
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The infrared sensor on the CI20 board is connected to a GPIO and can
be operated by using the gpio-ir-recv driver. Add a DT node for the
sensor to allow that driver to be used.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Nand controller v5.0 and v6.0 have nand edu blocks that enable
dma nand flash transfers. This allows for faster read and write
access.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Acked-by: Paul Burton <paulburton@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200122213313.35820-3-kdasu.kdev@gmail.com
Interrupts should not be specified by interrupt line but by
gpio parent and reference.
Fixes: 73f2b94047 ("MIPS: CI20: DTS: Add I2C nodes")
Cc: stable@vger.kernel.org
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
There is a ACT8600 on the CI20 board and the bindings of the
ACT8865 driver have changed without updating the CI20 device
tree. Therefore the PMU can not be probed successfully and
is running in power-on reset state.
Fix DT to match the latest act8865-regulator bindings.
Fixes: 73f2b94047 ("MIPS: CI20: DTS: Add I2C nodes")
Cc: stable@vger.kernel.org
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The devicetree ABI was broken on purpose by commit 6d532143c9
("watchdog: jz4740: Use regmap provided by TCU driver"), and
commit 1d9c307454 ("watchdog: jz4740: Use WDT clock provided
by TCU driver"). The commit message of the latter explains why the ABI
was broken.
However, the current devicetree files were not updated to the new ABI
described in Documentation/devicetree/bindings/timer/ingenic,tcu.txt,
so the watchdog driver would not probe.
Fix this problem by updating the watchdog nodes to comply with the new
ABI.
Fixes: 6d532143c9 ("watchdog: jz4740: Use regmap provided by TCU driver")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Zhou Yanjie <zhouyanjie@wanyeetech.com>
Cc: od@zcrc.me
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: <stable@vger.kernel.org> # v5.5+
The devicetree ABI was broken on purpose by commit 6d532143c9
("watchdog: jz4740: Use regmap provided by TCU driver"), and
commit 1d9c307454 ("watchdog: jz4740: Use WDT clock provided
by TCU driver"). The commit message of the latter explains why the ABI
was broken.
However, the current devicetree files were not updated to the new ABI
described in Documentation/devicetree/bindings/timer/ingenic,tcu.txt,
so the watchdog driver would not probe.
Fix this problem by updating the clock of watchdog node from
"&cgu X1000_CLK_RTCLK" to "&tcu TCU_CLK_WDT" to comply with the new
ABI.
Fixes: 7a16ccd300 ("[v8,1/4] MIPS: Ingenic: Add Ingenic X1000 support.").
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: paul@crapouillou.net
Cc: robh+dt@kernel.org
Cc: mark.rutland@arm.com
Cc: ralf@linux-mips.org
Cc: sernia.zhou@foxmail.com
Cc: zhenwenjin@gmail.com
Cc: dongsheng.qiu@ingenic.com
In old days, the "host-progs" syntax was used for specifying host
programs. It was renamed to the current "hostprogs-y" in 2004.
It is typically useful in scripts/Makefile because it allows Kbuild to
selectively compile host programs based on the kernel configuration.
This commit renames like follows:
always -> always-y
hostprogs-y -> hostprogs
So, scripts/Makefile will look like this:
always-$(CONFIG_BUILD_BIN2C) += ...
always-$(CONFIG_KALLSYMS) += ...
...
hostprogs := $(always-y) $(always-m)
I think this makes more sense because a host program is always a host
program, irrespective of the kernel configuration. We want to specify
which ones to compile by CONFIG options, so always-y will be handier.
The "always", "hostprogs-y", "hostprogs-m" will be kept for backward
compatibility for a while.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
- Support mremap() for the VDSO, primarily to allow CRIU to restore the
VDSO to its checkpointed location.
- Restore the MIPS32 cBPF JIT, after having reverted the enablement of
the eBPF JIT for MIPS32 systems in the 5.5 cycle.
- Improve cop0 counter synchronization behaviour whilst onlining CPUs by
running with interrupts disabled.
- Better match FPU behaviour when emulating multiply-accumulate
instructions on pre-r6 systems that implement IEEE754-2008 style MACs.
- Loongson64 kernels now build using the MIPS64r2 ISA, allowing them to
take advantage of instructions introduced by r2.
- Support for the Ingenic X1000 SoC & the really nice little CU Neo
development board that's using it.
- Support for WMAC on GARDENA Smart Gateway devices.
- Lots of cleanup & refactoring of SGI IP27 (Origin 2*) support in
preparation for introducing IP35 (Origin 3*) support.
- Various Kconfig & Makefile cleanups.
-----BEGIN PGP SIGNATURE-----
iIwEABYIADQWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXjRnpxYccGF1bGJ1cnRv
bkBrZXJuZWwub3JnAAoJED6nn6y1dQDdNYoA/3ZhgKX1L/hwvkPKwu7FxbL41pjB
WAm8IYDaxPvgxkcSAP9FNNepHK+oBPM8I2e3DvDvmcuYjumztdikzYbJ5HuMBA==
=MV2S
-----END PGP SIGNATURE-----
Merge tag 'mips_5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS changes from Paul Burton:
"Nothing too big or scary in here:
- Support mremap() for the VDSO, primarily to allow CRIU to restore
the VDSO to its checkpointed location.
- Restore the MIPS32 cBPF JIT, after having reverted the enablement
of the eBPF JIT for MIPS32 systems in the 5.5 cycle.
- Improve cop0 counter synchronization behaviour whilst onlining CPUs
by running with interrupts disabled.
- Better match FPU behaviour when emulating multiply-accumulate
instructions on pre-r6 systems that implement IEEE754-2008 style
MACs.
- Loongson64 kernels now build using the MIPS64r2 ISA, allowing them
to take advantage of instructions introduced by r2.
- Support for the Ingenic X1000 SoC & the really nice little CU Neo
development board that's using it.
- Support for WMAC on GARDENA Smart Gateway devices.
- Lots of cleanup & refactoring of SGI IP27 (Origin 2*) support in
preparation for introducing IP35 (Origin 3*) support.
- Various Kconfig & Makefile cleanups"
* tag 'mips_5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (60 commits)
MIPS: PCI: Add detection of IOC3 on IO7, IO8, IO9 and Fuel
MIPS: Loongson64: Disable exec hazard
MIPS: Loongson64: Bump ISA level to MIPSR2
MIPS: Make DIEI support as a config option
MIPS: OCTEON: octeon-irq: fix spelling mistake "to" -> "too"
MIPS: asm: local: add barriers for Loongson
MIPS: Loongson64: Select mac2008 only feature
MIPS: Add MAC2008 Support
Revert "MIPS: Add custom serial.h with BASE_BAUD override for generic kernel"
MIPS: sort MIPS and MIPS_GENERIC Kconfig selects alphabetically (again)
MIPS: make CPU_HAS_LOAD_STORE_LR opt-out
MIPS: generic: don't unconditionally select PINCTRL
MIPS: don't explicitly select LIBFDT in Kconfig
MIPS: sync-r4k: do slave counter synchronization with disabled HW interrupts
MIPS: SGI-IP30: Check for valid pointer before using it
MIPS: syscalls: fix indentation of the 'SYSNR' message
MIPS: boot: fix typo in 'vmlinux.lzma.its' target
MIPS: fix indentation of the 'RELOCS' message
dt-bindings: Document loongson vendor-prefix
MIPS: CU1000-Neo: Refresh defconfig to support HWMON and WiFi.
...
Commit 92b34a9763 ("MIPS: boot: add missing targets for vmlinux.*.its")
fixed constant rebuild of *.its files on every make invocation, but due
to typo ("lzmo") it made no sense for vmlinux.lzma.its.
Fixes: 92b34a9763 ("MIPS: boot: add missing targets for vmlinux.*.its")
Cc: <stable@vger.kernel.org> # v4.19+
Signed-off-by: Alexander Lobakin <alobakin@dlink.ru>
[paulburton@kernel.org: s/invokation/invocation/]
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Rob Herring <robh@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
The radio module asserts CTS when its RX buffer has 10 bytes left.
Putting just 8 instead of 16 bytes into the UART1 TX buffer on the Linux
side ensures to not overflow the RX buffer on the radio module side.
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Paul Burton <paul.burton@mips.com>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: linux-mips@vger.kernel.org
This patch enables the WMAC controller on the GARDENA smart Gateway and
configures the board specific factory EEPROM setting for this driver.
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Paul Burton <paul.burton@mips.com>
Cc: John Crispin <john@phrozen.org>
Cc: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: linux-mips@vger.kernel.org
This patch adds the WMAC controller description to the MT7628A dtsi file.
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Paul Burton <paul.burton@mips.com>
Cc: John Crispin <john@phrozen.org>
Cc: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: linux-mips@vger.kernel.org
The ungrafting from PRIO bug fixes in net, when merged into net-next,
merge cleanly but create a build failure. The resolution used here is
from Petr Machata.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add switch node supported by dsa ar9331 driver.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
__sanitizer_cov_trace_pc() is not linked in and causing link
failure if KCOV_INSTRUMENT is enabled. Fix this by disabling
instrumentation for compressed image.
Signed-off-by: Jouni Hogander <jouni.hogander@unikie.com>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Cc: linux-mips@vger.kernel.org
This patch adds support for the GARDENA smart Gateway, which is based on
the MediaTek MT7688 SoC. It is equipped with 128 MiB of DDR and 8 MiB of
flash (SPI NOR) and additional 128MiB SPI NAND storage.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Harvey Hunt <harveyhuntnexus@gmail.com>
Cc: John Crispin <john@phrozen.org>
Cc: linux-mips@vger.kernel.org
This patch adds the I2C controller description to the MT7628A dtsi file.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Harvey Hunt <harveyhuntnexus@gmail.com>
Cc: John Crispin <john@phrozen.org>
Cc: linux-mips@vger.kernel.org
It is two registers each of 4 byte.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
- boot_mem_map is removed, providing a nice cleanup made possible by the
recent removal of bootmem.
- Some fixes to atomics, in general providing compiler barriers for
smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs or
MIPS32 systems using cmpxchg64().
- Conversion to the new generic VDSO infrastructure courtesy of Vincenzo
Frascino.
- Removal of undefined behavior in set_io_port_base(), fixing the
behavior of some MIPS kernel configurations when built with recent
clang versions.
- Initial MIPS32 huge page support, functional on at least Ingenic SoCs.
- pte_special() is now supported for some configurations, allowing among
other things generic fast GUP to be used.
- Miscellaneous fixes & cleanups.
And platform specific changes:
- Major improvements to Ingenic SoC support from Paul Cercueil, mostly
enabled by the inclusion of the new TCU (timer-counter unit) drivers
he's spent a very patient year or so working on. Plus some fixes for
X1000 SoCs from Zhou Yanjie.
- Netgear R6200 v1 systems are now supported by the bcm47xx platform.
- DT updates for BMIPS, Lantiq & Microsemi Ocelot systems.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXYaqpRUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN2JUQD+PQGFIlq9bo/3vLyqsXJffm+DhwVQ
4WSCSeN5brPkO8EA/153sRJBlRtG+KK5p9f7WYKUuBfbcEawuc1uwmKuy7cG
=lWlM
-----END PGP SIGNATURE-----
Merge tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Paul Burton:
"Main MIPS changes:
- boot_mem_map is removed, providing a nice cleanup made possible by
the recent removal of bootmem.
- Some fixes to atomics, in general providing compiler barriers for
smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs
or MIPS32 systems using cmpxchg64().
- Conversion to the new generic VDSO infrastructure courtesy of
Vincenzo Frascino.
- Removal of undefined behavior in set_io_port_base(), fixing the
behavior of some MIPS kernel configurations when built with recent
clang versions.
- Initial MIPS32 huge page support, functional on at least Ingenic
SoCs.
- pte_special() is now supported for some configurations, allowing
among other things generic fast GUP to be used.
- Miscellaneous fixes & cleanups.
And platform specific changes:
- Major improvements to Ingenic SoC support from Paul Cercueil,
mostly enabled by the inclusion of the new TCU (timer-counter unit)
drivers he's spent a very patient year or so working on. Plus some
fixes for X1000 SoCs from Zhou Yanjie.
- Netgear R6200 v1 systems are now supported by the bcm47xx platform.
- DT updates for BMIPS, Lantiq & Microsemi Ocelot systems"
* tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (89 commits)
MIPS: Detect bad _PFN_SHIFT values
MIPS: Disable pte_special() for MIPS32 with RiXi
MIPS: ralink: deactivate PCI support for SOC_MT7621
mips: compat: vdso: Use legacy syscalls as fallback
MIPS: Drop Loongson _CACHE_* definitions
MIPS: tlbex: Remove cpu_has_local_ebase
MIPS: tlbex: Simplify r3k check
MIPS: Select R3k-style TLB in Kconfig
MIPS: PCI: refactor ioc3 special handling
mips: remove ioremap_cachable
mips/atomic: Fix smp_mb__{before,after}_atomic()
mips/atomic: Fix loongson_llsc_mb() wreckage
mips/atomic: Fix cmpxchg64 barriers
MIPS: Octeon: remove duplicated include from dma-octeon.c
firmware: bcm47xx_nvram: Allow COMPILE_TEST
firmware: bcm47xx_nvram: Correct size_t printf format
MIPS: Treat Loongson Extensions as ASEs
MIPS: Remove dev_err() usage after platform_get_irq()
MIPS: dts: mscc: describe the PTP ready interrupt
MIPS: dts: mscc: describe the PTP register range
...
CONFIG_SHELL falls back to sh when bash is not installed on the system,
but nobody is testing such a case since bash is usually installed.
So, shell scripts invoked by CONFIG_SHELL are only tested with bash.
It makes it difficult to test whether the hashbang #!/bin/sh is real.
For example, #!/bin/sh in arch/powerpc/kernel/prom_init_check.sh is
false. (I fixed it up)
Besides, some shell scripts invoked by CONFIG_SHELL use bash-extension
and #!/bin/bash is specified as the hashbang, while CONFIG_SHELL may
not always be set to bash.
Probably, the right thing to do is to introduce BASH, which is bash by
default, and always set CONFIG_SHELL to sh. Replace $(CONFIG_SHELL)
with $(BASH) for bash scripts.
If somebody tries to add bash-extension to a #!/bin/sh script, it will
be caught in testing because /bin/sh is a symlink to dash on some major
distributions.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Merge the Ingenic TCU patchset from the ingenic-tcu-v5.4 branch which
was created to enable follow-on changes in other subsystems.
Signed-off-by: Paul Burton <paul.burton@mips.com>
The default clock (12 MHz) is too fast for the system timer.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Cc: od@zcrc.me
The default clock (48 MHz) is too fast for the system timer.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Cc: od@zcrc.me
The default clock (12 MHz) is too fast for the system timer, which fails
to report time accurately.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Cc: od@zcrc.me
Add DTS nodes for the JZ4780, JZ4770 and JZ4740 devicetree files.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Cc: od@zcrc.me
Move all the platform data to devicetree.
The only bit dropped is the PWM beeper, which requires the PWM driver
to be updated. I figured it's okay to remove it here since it's really
a non-critical device, and it'll be re-introduced soon enough.
The other change is the CS line of the SPI is now set as active low. The
SPI core would have forced "active low" anyway, unless the 'spi-cs-high'
property is set.
In the process of moving to devicetree, we also switched to new drivers:
- We use the simple-audio-card and simple-amplifier drivers instead of
the custom ASoC code;
- We use the new Ingenic DRM driver coupled with the GiantPlus GPM940B0
DRM panel driver instead of the old framebuffer driver;
- We use the new jz4780-dma driver instead of the old jz4740-dma one;
- We use the ingenic-nand and jz4740-ecc drivers instead of the old
jz4740-nand driver;
- We use ingenic-battery instead of jz4740-battery;
- We use iio-hwmon instead of jz4740-hwmon;
- We use ingenic-iio instead of the old jz4740-adc MFD driver.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
[paul.burton@mips.com:
Drop the unused & undocumented ili8960 spi@0 node.]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Add nodes for the MMC, AIC, ADC, CODEC, MUSB, LCD, memory,
and BCH controllers.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Move the MMC configuration from the board C file to devicetree.
The 'power' GPIO was removed and instead the vmmc regulator is used,
to follow the changes introduced in the jz4740-mmc driver.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Now that we have a driver for the clock controller, add nodes to allow
devices to make use of it.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-clk@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
- Removal of readq & writeq for MIPS32 kernels where they would simply
BUG() anyway, allowing drivers or other code that #ifdefs on their
presence to work properly.
- Improvements for Ingenic JZ4740 systems, including support for the
external memory controller & pinmuxing fixes for qi_lb60/NanoNote
systems.
- Improvements for Lantiq systems, in particular around SMP & IPIs.
- DT updates for ralink/MediaTek MT7628a systems to probe & configure a
bunch more devices.
- Miscellaneous cleanups & build fixes.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXS85dBUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN2yJwEA6SUzzTXdywxEy78Ala3tzghMjkD5
818q6a9DREGofyIA/ie08di/MIYS9++ETsaQemVXoe7KT333+SgTeXCb1lIJ
=RiKE
-----END PGP SIGNATURE-----
Merge tag 'mips_5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Paul Burton:
"A light batch this time around but significant improvements for
certain systems:
- Removal of readq & writeq for MIPS32 kernels where they would
simply BUG() anyway, allowing drivers or other code that #ifdefs on
their presence to work properly.
- Improvements for Ingenic JZ4740 systems, including support for the
external memory controller & pinmuxing fixes for qi_lb60/NanoNote
systems.
- Improvements for Lantiq systems, in particular around SMP & IPIs.
- DT updates for ralink/MediaTek MT7628a systems to probe & configure
a bunch more devices.
- Miscellaneous cleanups & build fixes"
* tag 'mips_5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (30 commits)
MIPS: fix some more fall through errors in arch/mips
MIPS: perf events: handle switch statement falling through warnings
mips/kprobes: Export kprobe_fault_handler()
MAINTAINERS: Add myself as Ingenic SoCs maintainer
MIPS: ralink: mt7628a.dtsi: Add watchdog controller DT node
MIPS: ralink: mt7628a.dtsi: Add SPI controller DT node
MIPS: ralink: mt7628a.dtsi: Add GPIO controller DT node
MIPS: ralink: mt7628a.dtsi: Add pinctrl DT properties to the UART nodes
MIPS: ralink: mt7628a.dtsi: Add pinmux DT node
MIPS: ralink: mt7628a.dtsi: Add SPDX GPL-2.0 license identifier
MIPS: lantiq: Add SMP support for lantiq interrupt controller
MIPS: lantiq: Shorten register names, remove unused macros
MIPS: lantiq: Fix bitfield masking
MIPS: lantiq: Remove unused macros
MIPS: lantiq: Fix attributes of of_device_id structure
MIPS: lantiq: Change variables to the same type as the source
MIPS: lantiq: Move macro directly to iomem function
mips: Remove q-accessors from non-64bit platforms
FDDI: defza: Include linux/io-64-nonatomic-lo-hi.h
MIPS: configs: Remove useless UEVENT_HELPER_PATH
...
Pull networking updates from David Miller:
"Some highlights from this development cycle:
1) Big refactoring of ipv6 route and neigh handling to support
nexthop objects configurable as units from userspace. From David
Ahern.
2) Convert explored_states in BPF verifier into a hash table,
significantly decreased state held for programs with bpf2bpf
calls, from Alexei Starovoitov.
3) Implement bpf_send_signal() helper, from Yonghong Song.
4) Various classifier enhancements to mvpp2 driver, from Maxime
Chevallier.
5) Add aRFS support to hns3 driver, from Jian Shen.
6) Fix use after free in inet frags by allocating fqdirs dynamically
and reworking how rhashtable dismantle occurs, from Eric Dumazet.
7) Add act_ctinfo packet classifier action, from Kevin
Darbyshire-Bryant.
8) Add TFO key backup infrastructure, from Jason Baron.
9) Remove several old and unused ISDN drivers, from Arnd Bergmann.
10) Add devlink notifications for flash update status to mlxsw driver,
from Jiri Pirko.
11) Lots of kTLS offload infrastructure fixes, from Jakub Kicinski.
12) Add support for mv88e6250 DSA chips, from Rasmus Villemoes.
13) Various enhancements to ipv6 flow label handling, from Eric
Dumazet and Willem de Bruijn.
14) Support TLS offload in nfp driver, from Jakub Kicinski, Dirk van
der Merwe, and others.
15) Various improvements to axienet driver including converting it to
phylink, from Robert Hancock.
16) Add PTP support to sja1105 DSA driver, from Vladimir Oltean.
17) Add mqprio qdisc offload support to dpaa2-eth, from Ioana
Radulescu.
18) Add devlink health reporting to mlx5, from Moshe Shemesh.
19) Convert stmmac over to phylink, from Jose Abreu.
20) Add PTP PHC (Physical Hardware Clock) support to mlxsw, from
Shalom Toledo.
21) Add nftables SYNPROXY support, from Fernando Fernandez Mancera.
22) Convert tcp_fastopen over to use SipHash, from Ard Biesheuvel.
23) Track spill/fill of constants in BPF verifier, from Alexei
Starovoitov.
24) Support bounded loops in BPF, from Alexei Starovoitov.
25) Various page_pool API fixes and improvements, from Jesper Dangaard
Brouer.
26) Just like ipv4, support ref-countless ipv6 route handling. From
Wei Wang.
27) Support VLAN offloading in aquantia driver, from Igor Russkikh.
28) Add AF_XDP zero-copy support to mlx5, from Maxim Mikityanskiy.
29) Add flower GRE encap/decap support to nfp driver, from Pieter
Jansen van Vuuren.
30) Protect against stack overflow when using act_mirred, from John
Hurley.
31) Allow devmap map lookups from eBPF, from Toke Høiland-Jørgensen.
32) Use page_pool API in netsec driver, Ilias Apalodimas.
33) Add Google gve network driver, from Catherine Sullivan.
34) More indirect call avoidance, from Paolo Abeni.
35) Add kTLS TX HW offload support to mlx5, from Tariq Toukan.
36) Add XDP_REDIRECT support to bnxt_en, from Andy Gospodarek.
37) Add MPLS manipulation actions to TC, from John Hurley.
38) Add sending a packet to connection tracking from TC actions, and
then allow flower classifier matching on conntrack state. From
Paul Blakey.
39) Netfilter hw offload support, from Pablo Neira Ayuso"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2080 commits)
net/mlx5e: Return in default case statement in tx_post_resync_params
mlx5: Return -EINVAL when WARN_ON_ONCE triggers in mlx5e_tls_resync().
net: dsa: add support for BRIDGE_MROUTER attribute
pkt_sched: Include const.h
net: netsec: remove static declaration for netsec_set_tx_de()
net: netsec: remove superfluous if statement
netfilter: nf_tables: add hardware offload support
net: flow_offload: rename tc_cls_flower_offload to flow_cls_offload
net: flow_offload: add flow_block_cb_is_busy() and use it
net: sched: remove tcf block API
drivers: net: use flow block API
net: sched: use flow block API
net: flow_offload: add flow_block_cb_{priv, incref, decref}()
net: flow_offload: add list handling functions
net: flow_offload: add flow_block_cb_alloc() and flow_block_cb_free()
net: flow_offload: rename TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_*
net: flow_offload: rename TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND
net: flow_offload: add flow_block_cb_setup_simple()
net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC
net: hisilicon: Add an rx_desc to adapt HI13X1_GMAC
...
- Fix a silly typo in virt_addr_valid which led to completely bogus
behavior (that happened to stop tripping up hardened usercopy despite
being broken).
- Fix UART parity setup on AR933x systems.
- A build fix for non-Linux build machines.
- Have the 'all' make target build DTBs, primarily to fit in with the
behavior of scripts/package/builddeb.
- Handle an execution hazard in TLB exceptions that use KScratch
registers, which could inadvertently clobber the $1 register on some
generally higher-end out-of-order CPUs.
- A MAINTAINERS update to fix the path to the NAND driver for Ingenic
systems.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXSDJfhUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN35ygEA30KckazfjbtmW0EqD+C19sgtbSS3
eCAiweHHwLJoyUUBAJ/HzlZ8ap2X9ilZuFdzKEf1igj5WsLIyrkl6kkauUEA
=DRYO
-----END PGP SIGNATURE-----
Merge tag 'mips_fixes_5.2_2' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Paul Burton:
"A few more MIPS fixes:
- Fix a silly typo in virt_addr_valid which led to completely bogus
behavior (that happened to stop tripping up hardened usercopy
despite being broken).
- Fix UART parity setup on AR933x systems.
- A build fix for non-Linux build machines.
- Have the 'all' make target build DTBs, primarily to fit in with the
behavior of scripts/package/builddeb.
- Handle an execution hazard in TLB exceptions that use KScratch
registers, which could inadvertently clobber the $1 register on
some generally higher-end out-of-order CPUs.
- A MAINTAINERS update to fix the path to the NAND driver for Ingenic
systems"
* tag 'mips_fixes_5.2_2' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MAINTAINERS: Correct path to moved files
MIPS: Add missing EHB in mtc0 -> mfc0 sequence.
MIPS: have "plain" make calls build dtbs for selected platforms
MIPS: fix build on non-linux hosts
MIPS: ath79: fix ar933x uart parity mode
MIPS: Fix bounds check virt_addr_valid
This patch adds the watchdog controller description to the MT7628A dtsi
file.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Harvey Hunt <harveyhuntnexus@gmail.com>
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
This patch adds the SPI controller description to the MT7628A dtsi file.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Harvey Hunt <harveyhuntnexus@gmail.com>
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
This patch adds the GPIO controller description to the MT7628A dtsi file.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Harvey Hunt <harveyhuntnexus@gmail.com>
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Now that pinmux is available, let's use it for the UART DT nodes.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Harvey Hunt <harveyhuntnexus@gmail.com>
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
This patch adds the pinmux DT node using the generic "pinctrl-single"
pinmux driver. For this the system-controller register area needs to be
changed to not overlap with the pinmux registers.
This patch is based on work done by John Crispin.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Harvey Hunt <harveyhuntnexus@gmail.com>
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
As done in commit b24413180f ("License cleanup: add SPDX GPL-2.0
license identifier to files with no license"), this patch adds the SPDX
license identifier to mt7628a.dtsi, which is currently still missing
this identifier.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Harvey Hunt <harveyhuntnexus@gmail.com>
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
calc_vmlinuz_load_addr.c requires SZ_64K to be defined for alignment
purposes. It included "../../../../include/linux/sizes.h" to define
that size, however "sizes.h" tries to include <linux/const.h> which
assumes linux system headers. These may not exist eg. the following
error was encountered when building Linux for OpenWrt under macOS:
In file included from arch/mips/boot/compressed/calc_vmlinuz_load_addr.c:16:
arch/mips/boot/compressed/../../../../include/linux/sizes.h:11:10: fatal error: 'linux/const.h' file not found
^~~~~~~~~~
Change makefile to force building on local linux headers instead of
system headers. Also change eye-watering relative reference in include
file spec.
Thanks to Jo-Philip Wich & Petr Štetiar for assistance in tracking this
down & fixing.
Suggested-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ACL support using the TCAM. Using ACL it is possible to create rules
in hardware to filter/redirect frames.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add ethernet nodes supported by ag71xx driver.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- do not generate unneeded top-level built-in.a
- let git ignore O= directory entirely
- optimize scripts/kallsyms slightly
- exclude DWARF info from *.s regardless of config options
- fix GCC toolchain search path for Clang to prepare ld.lld support
- do not generate modules.order when CONFIG_MODULES is disabled
- simplify single target rules and remove VPATH for external module build
- allow to add optional flags to dpkg-buildpackage when building deb-pkg
- move some compiler option tests from Makefile to Kconfig
- various Makefile cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJcgxYUAAoJED2LAQed4NsGr7YQAJq4LmN/aZDI9Mt0YAQjEyyA
PCpm8J2HI9HO1sMoY7J/ksWmV0BU25G+uspKD7dXAQo3l9fmahQM5e4dsyZ4Xqs8
DyyYSGtJJnMJaWmupIZNA4UKDCVtwPoVW8YeuK9rwADVokCux9avogof9O1OoA/E
Pylo+I4UCM82kbpZSd+UxnCx6B0v8XGtW+d31Q4yZXCkw5nw14chrlaprcqB3UgB
+7C3xOnDWCi7gyxaTqmD7dLay2DM8KCDlznEvBL733Y/cK3to1fywzEPzp0JQCLX
BLgmmpW13NF++q5BCoTW6sFjZAhBVbiYZwesMrCi75Y32T8zt4G5l4pkvGkSuGF/
UQh5aoCxaMIp70VPj/loZ0lh78nwVGTok9zRb0rfztM0X4DbmiPi5MNiHRzRpIeE
1jjEa/GK1t0TDnXc/MuDFK8cWwdhttIqUL5yWfAxjXbtP27eLtsopQUdW7EPHs7d
sMnfuSUuhOC28yByVxIkBcwawLyYrcWRphJ3ixCO70CoJWt2DT6aOKxcFJefoJix
Pto6Oo3oQ4iypMM5M9/0Uo+AK2TKRejWIqtZdbo+ir70tNxVH3WDZq++fG0drXOB
r2I/GY6nRjuzLOe2jzEqywFTFd2xpk4Qo84LGb1R3U6aU5qS2gA0W/q00JS5c2qU
R8uReJ7bvmLmrVNZ/NI4
=y9YG
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- do not generate unneeded top-level built-in.a
- let git ignore O= directory entirely
- optimize scripts/kallsyms slightly
- exclude DWARF info from *.s regardless of config options
- fix GCC toolchain search path for Clang to prepare ld.lld support
- do not generate modules.order when CONFIG_MODULES is disabled
- simplify single target rules and remove VPATH for external module
build
- allow to add optional flags to dpkg-buildpackage when building
deb-pkg
- move some compiler option tests from Makefile to Kconfig
- various Makefile cleanups
* tag 'kbuild-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (40 commits)
kbuild: remove scripts/basic/% build target
kbuild: use -Werror=implicit-... instead of -Werror-implicit-...
kbuild: clean up scripts/gcc-version.sh
kbuild: remove cc-version macro
kbuild: update comment block of scripts/clang-version.sh
kbuild: remove commented-out INITRD_COMPRESS
kbuild: move -gsplit-dwarf, -gdwarf-4 option tests to Kconfig
kbuild: [bin]deb-pkg: add DPKG_FLAGS variable
kbuild: move ".config not found!" message from Kconfig to Makefile
kbuild: invoke syncconfig if include/config/auto.conf.cmd is missing
kbuild: simplify single target rules
kbuild: remove empty rules for makefiles
kbuild: make -r/-R effective in top Makefile for old Make versions
kbuild: move tools_silent to a more relevant place
kbuild: compute false-positive -Wmaybe-uninitialized cases in Kconfig
kbuild: refactor cc-cross-prefix implementation
kbuild: hardcode genksyms path and remove GENKSYMS variable
scripts/gdb: refactor rules for symlink creation
kbuild: create symlink to vmlinux-gdb.py in scripts_gdb target
scripts/gdb: do not descend into scripts/gdb from scripts
...
- Support for the MIPSr6 MemoryMapID register & Global INValidate TLB
(GINVT) instructions, allowing for more efficient TLB maintenance when
running on a CPU such as the I6500 that supports these.
- Enable huge page support for MIPS64r6.
- Optimize post-DMA cache sync by removing that code entirely for kernel
configurations in which we know it won't be needed.
- The number of pages allocated for interrupt stacks is now calculated
correctly, where before we would wastefully allocate too much memory
in some configurations.
- The ath79 platform migrates to devicetree.
- The bcm47xx platform sees fixes for the Buffalo WHR-G54S board.
- The ingenic/jz4740 platform gains support for appended devicetrees.
- The cavium_octeon, lantiq, loongson32 & sgi-ip27 platforms all see
cleanups as do various pieces of core architecture code.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXH3BQxUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN1+4wD+Oh4JTfZN/NEOQMlrSkXxjEHqjX3u
1Y6CiiPCs+q2UnYBANb+ic+ZH5MnvJxxmcvlYI2q3rIh4b8TDriip4KMUTUP
=Sw9X
-----END PGP SIGNATURE-----
Merge tag 'mips_5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Paul Burton:
- Support for the MIPSr6 MemoryMapID register & Global INValidate TLB
(GINVT) instructions, allowing for more efficient TLB maintenance
when running on a CPU such as the I6500 that supports these.
- Enable huge page support for MIPS64r6.
- Optimize post-DMA cache sync by removing that code entirely for
kernel configurations in which we know it won't be needed.
- The number of pages allocated for interrupt stacks is now calculated
correctly, where before we would wastefully allocate too much memory
in some configurations.
- The ath79 platform migrates to devicetree.
- The bcm47xx platform sees fixes for the Buffalo WHR-G54S board.
- The ingenic/jz4740 platform gains support for appended devicetrees.
- The cavium_octeon, lantiq, loongson32 & sgi-ip27 platforms all see
cleanups as do various pieces of core architecture code.
* tag 'mips_5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (66 commits)
MIPS: lantiq: Remove separate GPHY Firmware loader
MIPS: ingenic: Add support for appended devicetree
MIPS: SGI-IP27: rework HUB interrupts
MIPS: SGI-IP27: do boot CPU init later
MIPS: SGI-IP27: do xtalk scanning later
MIPS: SGI-IP27: use pr_info/pr_emerg and pr_cont to fix output
MIPS: SGI-IP27: clean up bridge access and header files
MIPS: SGI-IP27: get rid of volatile and hubreg_t
MIPS: irq: Allocate accurate order pages for irq stack
MIPS: dma-noncoherent: Remove bogus condition in dma_sync_phys()
MIPS: eBPF: Remove REG_32BIT_ZERO_EX
MIPS: eBPF: Always return sign extended 32b values
MIPS: CM: Fix indentation
MIPS: BCM47XX: Fix/improve Buffalo WHR-G54S support
MIPS: OCTEON: program rx/tx-delay always from DT
MIPS: OCTEON: delete board-specific link status
MIPS: OCTEON: don't lie about interface type of CN3005 board
MIPS: OCTEON: warn if deprecated link status is being used
MIPS: OCTEON: add fixed-link nodes to in-kernel device tree
MIPS: Delete unused flush_cache_sigtramp()
...
Program rx/tx-delay always from DT.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Currently OCTEON ethernet falls back to phyless operation on
boards where we have no known PHY address or a fixed-link node.
Add fixed-link support for boards that need it, so we can clean up
the platform code and ethernet driver from some legacy code.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
DTC introduced an i2c_bus_reg check in v1.4.7, used since Linux v4.20,
which complains about upper case addresses used in the unit name.
nexys4ddr.dts names an I2C device node "ad7420@4B", leading to:
arch/mips/boot/dts/xilfpga/nexys4ddr.dts:109.16-112.8: Warning
(i2c_bus_reg): /i2c@10A00000/ad7420@4B: I2C bus unit address format
error, expected "4b"
Fix this by switching to lower case addresses throughout the file, as is
*mostly* the case in the file already & fairly standard throughout the
tree.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: stable@vger.kernel.org # v4.20+
Cc: linux-mips@vger.kernel.org
In Kbuild, if_changed and friends must have FORCE as a prerequisite.
Hence, $(filter-out FORCE,$^) or $(filter-out $(PHONY),$^) is a common
idiom to get the names of all the prerequisites except phony targets.
Add real-prereqs as a shorthand.
Note:
We cannot replace $(filter %.o,$^) in cmd_link_multi-m because $^ may
include auto-generated dependencies from the .*.cmd file when a single
object module is changed into a multi object module. Refer to commit
69ea912fda ("kbuild: remove unneeded link_multi_deps"). I added some
comment to avoid accidental breakage.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
The interrupt number set in the devicetree node of the DMA driver was
wrong.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Remove the Malta display platform code in favour of probing the
img-ascii-lcd driver via device tree. This reduces the amount of
platform code & the img-ascii-lcd driver offers us advantages in terms
of code sharing with other boards & functionality such as changing the
displayed message via sysfs. Defconfigs are untouched because the driver
already defaults y on when CONFIG_MIPS_MALTA=y.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21182/
Cc: linux-mips@linux-mips.org
KEXEC needs the new kernel's load address to be aligned on a page
boundary (see sanity_check_segment_list()), but on MIPS the default
vmlinuz load address is only explicitly aligned to 16 bytes.
Since the largest PAGE_SIZE supported by MIPS kernels is 64KB, increase
the alignment calculated by calc_vmlinuz_load_addr to 64KB.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21131/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <james.hogan@mips.com>
Cc: Steven J . Hill <Steven.Hill@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: <stable@vger.kernel.org> # 2.6.36+
The Intel EG20T Platform Controller Hub used on the MIPS Boston
development board supports prefetching memory to optimize DMA transfers.
Unfortunately for unknown reasons this doesn't work well with some MIPS
CPUs such as the P6600, particularly when using an I/O Coherence Unit
(IOCU) to provide cache-coherent DMA. In these systems it is common for
DMA data to be lost, resulting in broken access to EG20T devices such as
the MMC or SATA controllers.
Support for a DT property to configure the prefetching was added a while
back by commit 549ce8f134 ("misc: pch_phub: Read prefetch value from
device tree if passed") but we never added the DT snippet to make use of
it. Add that now in order to disable the prefetching & fix DMA on the
affected systems.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21068/
Cc: linux-mips@linux-mips.org
- kexec support for the generic MIPS platform when running on a CPU
including the MIPS Coherence Manager & related hardware.
- Improvements to the definition of memory barriers used around MMIO
accesses, and fixes in their use.
- Switch to CONFIG_NO_BOOTMEM from Mike Rapoport, finally dropping
reliance on the old bootmem code.
- A number of fixes & improvements for Loongson 3 systems.
- DT & config updates for the Microsemi Ocelot platform.
- Workaround to enable USB power on the Netgear WNDR3400v3.
- Various cleanups & fixes.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCW9NfwRUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN1LNgD9Hy73DkYnnYeLNLcCe+5QMCr+NO2C
kwIs7kAI40X+/LQA/RgCcg6z4rUSH38hfNEobD6VXva7QiFhiYcJj5rCFH8O
=nDQg
-----END PGP SIGNATURE-----
Merge tag 'mips_4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Paul Burton:
- kexec support for the generic MIPS platform when running on a CPU
including the MIPS Coherence Manager & related hardware.
- Improvements to the definition of memory barriers used around MMIO
accesses, and fixes in their use.
- Switch to CONFIG_NO_BOOTMEM from Mike Rapoport, finally dropping
reliance on the old bootmem code.
- A number of fixes & improvements for Loongson 3 systems.
- DT & config updates for the Microsemi Ocelot platform.
- Workaround to enable USB power on the Netgear WNDR3400v3.
- Various cleanups & fixes.
* tag 'mips_4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (51 commits)
MIPS: Cleanup DSP ASE detection
MIPS: dts: Change upper case to lower case
MIPS: generic: Add Network, SPI and I2C to ocelot_defconfig
MIPS: Loongson-3: Fix BRIDGE irq delivery problem
MIPS: Loongson-3: Fix CPU UART irq delivery problem
MIPS: Remove unused PREF, PREFE & PREFX macros
MIPS: lib: Use kernel_pref & user_pref in memcpy()
MIPS: Remove unused CAT macro
MIPS: Add kernel_pref & user_pref helpers
MIPS: Remove unused TTABLE macro
MIPS: Remove unused PIC macros
MIPS: Remove unused MOVN & MOVZ macros
MIPS: Provide actually relaxed MMIO accessors
MIPS: Enforce strong ordering for MMIO accessors
MIPS: Correct `mmiowb' barrier for `wbflush' platforms
MIPS: Define MMIO ordering barriers
MIPS: mscc: add PCB120 to the ocelot fitImage
MIPS: mscc: add DT for Ocelot PCB120
MIPS: memset: Limit excessive `noreorder' assembly mode use
MIPS: memset: Fix CPU_DADDI_WORKAROUNDS `small_fixup' regression
...
Change this time round are:
- Support for ColdFire mcf5441x edma controller
- Support for link list mode in sprd dma
- More users of managed dmaenginem_async_device_register API
- Cyclic mode support in owl dma driver
- DT updates for renesas drivers, dma-jz4780 updates and support for
JZ4770, JZ4740 and JZ4725B controllers
- Removal of deprecated dma_slave_config direction in dmaengine drivers,
few more users will be removed in next cycle and eventually users.
- Minor updates to idma64, ioat, pxa, ppc drivers
-----BEGIN PGP SIGNATURE-----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=/pTg
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.20-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
- Support for ColdFire mcf5441x edma controller
- Support for link list mode in sprd dma
- More users of managed dmaenginem_async_device_register API
- Cyclic mode support in owl dma driver
- DT updates for renesas drivers, dma-jz4780 updates and support for
JZ4770, JZ4740 and JZ4725B controllers
- Removal of deprecated dma_slave_config direction in dmaengine
drivers, few more users will be removed in next cycle and eventually
removed.
- Minor updates to idma64, ioat, pxa, ppc drivers
* tag 'dmaengine-4.20-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (66 commits)
dmaengine: ppc4xx: fix off-by-one build failure
dmaengine: owl: Fix warnings generated during build
dmaengine: fsl-edma: remove dma_slave_config direction usage
dmaengine: rcar-dmac: set scatter/gather max segment size
dmaengine: mmp_tdma: remove dma_slave_config direction usage
dmaengine: ep93xx_dma: remove dma_slave_config direction usage
dmaengine: k3dma: remove dma_slave_config direction usage
dmaengine: k3dma: dont use direction for memcpy
dmaengine: imx-dma: remove dma_slave_config direction usage
dmaengine: idma: remove dma_slave_config direction usage
dmaengine: hsu: remove dma_slave_config direction usage
dmaengine: dw: remove dma_slave_config direction usage
dmaengine: jz4740: remove dma_slave_config direction usage
dmaengine: coh901318: remove dma_slave_config direction usage
dmaengine: bcm2835: remove dma_slave_config direction usage
dmaengine: at_hdmac: remove dma_slave_config direction usage
dmaengine: owl: Add Slave and Cyclic mode support for Actions Semi Owl S900 SoC
dmaengine: ioat: fix prototype of ioat_enumerate_channels
dmaengine: stm32-dma: check whether length is aligned on FIFO threshold
dt-bindings: dmaengine: usb-dmac: Add binding for r8a7744
...
All the upper case in unit-address and hex constants are
changed to lower case according to the DT conventions.
Signed-off-by: Songjun Wu <songjun.wu@linux.intel.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Patchwork: https://patchwork.linux-mips.org/patch/20768/
Cc: yixin.zhu@linux.intel.com
Cc: chuanhua.lei@linux.intel.com
Cc: hauke.mehrtens@intel.com
Cc: devicetree@vger.kernel.org
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
The Microsemi Ocelot has a set of register for SerDes/switch port muxing
as well as PCIe muxing for a specific SerDes, so let's add the device
and all SerDes in the Device Tree.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HSIO contains registers for PLL5 configuration, SerDes/switch port
muxing and a thermal sensor, hence we can't keep it in the switch DT
node.
Acked-by: Paul Burton <paul.burton@mips.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the devicetree nodes for the DMA core of the JZ4740 SoC, disabled
by default, as currently there are no clients for the DMA driver
(until the MMC driver and/or others get a devicetree node).
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add the two devicetree nodes for the two DMA cores of the JZ4770 SoC,
disabled by default, as currently there are no clients for the DMA
driver (until the MMC driver and/or others get a devicetree node).
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver now accepts two memory resources, the first one for the
channel-specific registers, the second one for the controller-specific
registers.
Note that older devicetrees, without this commit, will still work with
the jz4780-dma driver.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Enable the i2c controller on ocelot PCB123. While there are no i2c devices
on the board itself, it can be used to control the SFP transceivers.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20352/
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: linux-i2c@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Allan Nielsen <allan.nielsen@microchip.com>
Ocelot has an i2c controller, add it. There is only one possible pinmux
configuration so add it as well.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20353/
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: linux-i2c@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Allan Nielsen <allan.nielsen@microchip.com>
Commit a0f97e06a4 ("kbuild: enable 'make CFLAGS=...' to add
additional options to CC") renamed CFLAGS to KBUILD_CFLAGS.
Commit 222d394d30 ("kbuild: enable 'make AFLAGS=...' to add
additional options to AS") renamed AFLAGS to KBUILD_AFLAGS.
Commit 06c5040cdb ("kbuild: enable 'make CPPFLAGS=...' to add
additional options to CPP") renamed CPPFLAGS to KBUILD_CPPFLAGS.
For some reason, LDFLAGS was not renamed.
Using a well-known variable like LDFLAGS may result in accidental
override of the variable.
Kbuild generally uses KBUILD_ prefixed variables for the internally
appended options, so here is one more conversion to sanitize the
naming convention.
I did not touch Makefiles under tools/ since the tools build system
is a different world.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
The binding for the USB PHY went thru before the driver. However the
new version of the driver now use the PHY core support for reset, and
this expect the reset to be named "phy". So remove the "usb-" prefix
from the the reset names.
Signed-off-by: Alban Bedel <albeu@free.fr>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/15282/
Cc: linux-kernel@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Antony Pavlov <antonynpavlov@gmail.com>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Ocelot now has a u-boot port, allow building FIT images instead of relying
on the legacy detection and builtin DTB.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19632/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Make use of the spi-gpio driver to provide SPI support on the Ingenic
JZ4780 SoC using the pins that can be used with the SSI0 device as
GPIOs, until such time as we have support for the Ingenic SPI/SSI
controller.
[paul.burton@mips.com: Rewrite commit message.]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19489/
Cc: James Hogan <jhogan@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
prom_putchar() is used centrally in early printk infrastructure therefore
at least MIPS should agree on the function return type.
[paul.burton@mips.com:
- Include linux/types.h in asm/setup.h to gain the bool typedef before
we start include asm/setup.h elsewhere.
- Include asm/setup.h in all files that use or define prom_putchar().
- Also standardise on signed rather than unsigned char argument.]
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19842/
Cc: linux-mips@linux-mips.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Merge the build rule of vmlinux.{gz,bz2,lzma,lzo}.itb, and also move
'targets' close to the related code.
[paul.burton@mips.com:
- Remove leading tabs from assignments to itb_addr_cells, since after
this patch moves the additions to the 'targets' variable the
assignments to itb_addr_cells wound up being treated as part of the
uImage rule above them, causing the .its to incorrectly be generated
with empty ADDR_CELLS.]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Patchwork: https://patchwork.linux-mips.org/patch/19095/
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: linux-kernel@vger.kernel.org
The build rule of vmlinux.*.its is invoked by $(call if_changed,...)
but it always rebuilds the target needlessly due to missing targets.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Patchwork: https://patchwork.linux-mips.org/patch/19092/
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: linux-kernel@vger.kernel.org
As Documentation/kbuild/makefile.txt says, it is a typical mistake
to forget the FORCE prerequisite for the rule invoked by if_changed.
Add the FORCE to the prerequisite, but it must be filtered-out from
the files passed to the 'cat' command. Because this rule generates
.vmlinux.its.S.cmd, vmlinux.its.S must be specified as targets so
that the .cmd file is included.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Patchwork: https://patchwork.linux-mips.org/patch/19097/
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: linux-kernel@vger.kernel.org
$(CPP) is used here to perform macro replacement in ITS. Do not
pass $(cpp_flags) because it pulls in more options for dependency
file generation etc. but none of which is necessary here. ITS files
do not include any header file, so $(call if_change,...) is enough.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Patchwork: https://patchwork.linux-mips.org/patch/19093/
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: linux-kernel@vger.kernel.org
This reverts commit 0f9da844d8.
It is true that commit 0f9da844d8 ("MIPS: boot: Define __ASSEMBLY__
for its.S build") fixed the build error, but it should not have
defined __ASSEMBLY__ just for textual substitution in arbitrary data.
The file is image tree source in this case, but the purpose of using
CPP is to replace some macros.
I merged a better solution, commit a95b37e20d ("kbuild: get
<linux/compiler_types.h> out of <linux/kconfig.h>"). The original
fix-up is no longer needed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Patchwork: https://patchwork.linux-mips.org/patch/19096/
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: linux-kernel@vger.kernel.org
Use fixed width integer types for ecoff structs to make elf2ecoff work
on 64bit host machines.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Reviewed-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19483/
Signed-off-by: Paul Burton <paul.burton@mips.com>
- Decrease polling rate for erase/trim/discard
- Allow non-sleeping GPIOs for card detect
- Improve mmc block removal path
- Enable support for mmc_sw_reset() for SDIO cards
- Add mmc_sw_reset() to allow users to do a soft reset of the card
- Allow power delay to be tunable via DT
- Allow card detect debounce delay to be tunable via DT
- Enable new quirk to limit clock rate for Marvell 8887 chip
- Don't show eMMC RPMB and BOOT areas in /proc/partitions
- Add capability to avoid 3.3V signaling for fragile HWs
MMC host:
- Improve/fixup support for handle highmem pages
- Remove depends on HAS_DMA in case of platform dependency
- mvsdio: Enable support for erase/trim/discard
- rtsx_usb: Enable support for erase/trim/discard
- renesas_sdhi: Fix WP logic regressions
- renesas_sdhi: Add r8a77965 support
- renesas_sdhi: Add R8A77980 to whitelist
- meson: Add optional support for device reset
- meson: Add support for the Meson-AXG platform
- dw_mmc: Add new driver for BlueField DW variant
- mediatek: Add support for 64G DRAM DMA
- sunxi: Deploy runtime PM support
- jz4740: Add support for JZ4780
- jz4740: Enable support for DT based platforms
- sdhci: Various improvement to timeout handling
- sdhci: Disable support for HS200/HS400/UHS when no 1.8V support
- sdhci-omap: Add support for controller in k2g SoC
- sdhci-omap: Add workarounds for a couple of Erratas
- sdhci-omap: Enable support for generic sdhci DT properties
- sdhci-cadence: Re-send tune request to deal with errata
- sdhci-pci: Fix 3.3V voltage switch for some BYT-based Intel controllers
- sdhci-pci: Avoid 3.3V signaling on some NI 904x
- sdhci-esdhc-imx: Use watermark levels for PIO access
- sdhci-msm: Improve card detection handling
- sdhci-msm: Add support voltage pad switching
-----BEGIN PGP SIGNATURE-----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=MwCT
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Decrease polling rate for erase/trim/discard
- Allow non-sleeping GPIOs for card detect
- Improve mmc block removal path
- Enable support for mmc_sw_reset() for SDIO cards
- Add mmc_sw_reset() to allow users to do a soft reset of the card
- Allow power delay to be tunable via DT
- Allow card detect debounce delay to be tunable via DT
- Enable new quirk to limit clock rate for Marvell 8887 chip
- Don't show eMMC RPMB and BOOT areas in /proc/partitions
- Add capability to avoid 3.3V signaling for fragile HWs
MMC host:
- Improve/fixup support for handle highmem pages
- Remove depends on HAS_DMA in case of platform dependency
- mvsdio: Enable support for erase/trim/discard
- rtsx_usb: Enable support for erase/trim/discard
- renesas_sdhi: Fix WP logic regressions
- renesas_sdhi: Add r8a77965 support
- renesas_sdhi: Add R8A77980 to whitelist
- meson: Add optional support for device reset
- meson: Add support for the Meson-AXG platform
- dw_mmc: Add new driver for BlueField DW variant
- mediatek: Add support for 64G DRAM DMA
- sunxi: Deploy runtime PM support
- jz4740: Add support for JZ4780
- jz4740: Enable support for DT based platforms
- sdhci: Various improvement to timeout handling
- sdhci: Disable support for HS200/HS400/UHS when no 1.8V support
- sdhci-omap: Add support for controller in k2g SoC
- sdhci-omap: Add workarounds for a couple of Erratas
- sdhci-omap: Enable support for generic sdhci DT properties
- sdhci-cadence: Re-send tune request to deal with errata
- sdhci-pci: Fix 3.3V voltage switch for some BYT-based Intel controllers
- sdhci-pci: Avoid 3.3V signaling on some NI 904x
- sdhci-esdhc-imx: Use watermark levels for PIO access
- sdhci-msm: Improve card detection handling
- sdhci-msm: Add support voltage pad switching"
* tag 'mmc-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (104 commits)
mmc: renesas_sdhi: really fix WP logic regressions
mmc: mvsdio: Enable MMC_CAP_ERASE
mmc: mvsdio: Respect card busy time out from mmc core
mmc: sdhci-msm: Remove NO_CARD_NO_RESET quirk
mmc: sunxi: Use ifdef rather than __maybe_unused
mmc: mxmmc: Use ifdef rather than __maybe_unused
mmc: mxmmc: include linux/highmem.h
mmc: sunxi: mark PM functions as __maybe_unused
mmc: Throttle calls to MMC_SEND_STATUS during mmc_do_erase()
mmc: au1xmmc: handle highmem pages
mmc: Allow non-sleeping GPIO cd
mmc: sdhci-*: Don't emit error msg if sdhci_add_host() fails
mmc: sd: Define name for default speed dtr
mmc: core: Move calls to ->prepare_hs400_tuning() closer to mmc code
mmc: sdhci-xenon: use match_string() helper
mmc: wbsd: handle highmem pages
mmc: ushc: handle highmem pages
mmc: mxcmmc: handle highmem pages
mmc: atmel-mci: use sg_copy_{from,to}_buffer
mmc: android-goldfish: use sg_copy_{from,to}_buffer
...
Add phy to switch port connections for PCB123 for internal PHYs.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: linux-mips@linux-mips.org
Cc: netdev@vger.kernel.org
Signed-off-by: James Hogan <jhogan@kernel.org>
Ocelot has an integrated switch, add support for it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: linux-mips@linux-mips.org
Cc: netdev@vger.kernel.org
Signed-off-by: James Hogan <jhogan@kernel.org>
- The previous node requested a memory area of 0x100 bytes, while the
driver only manipulates four registers present in the first 0x10 bytes.
- The driver requests for the "rtc" clock, but the previous node did not
provide any.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Mathieu Malaterre <malat@debian.org>
Acked-by: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-watchdog@vger.kernel.org
Signed-off-by: James Hogan <jhogan@kernel.org>
Also remove the watchdog platform_device from platform.c, since it
wasn't used anywhere anyway.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: linux-mips@linux-mips.org
Cc: linux-watchdog@vger.kernel.org
Cc: devicetree@vger.kernel.org
[jhogan@kernel.org: Drop jz4740_wdt_device declaration from header]
Signed-off-by: James Hogan <jhogan@kernel.org>
A dtb.o is generated from nexys4ddr.dts but this is never used since it
has been moved to mips/generic with commit b35565bb16 ("MIPS: generic:
Add support for MIPSfpga").
Fixes: b35565bb16 ("MIPS: generic: Add support for MIPSfpga")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.15+
Patchwork: https://patchwork.linux-mips.org/patch/19244/
Signed-off-by: James Hogan <jhogan@kernel.org>
The debug definitions were missing for MACH_JZ4770, resulting in a build
failure when DEBUG_ZBOOT was set.
Since the UART addresses are the same across all Ingenic SoCs, we just
use a #ifdef CONFIG_MACH_INGENIC instead of checking for individual
Ingenic SoCs.
Additionally, I added a #define for the UART0 address in-code and
dropped the <asm/mach-jz4740/base.h> include, for the reason that this
include file is slowly being phased out as the whole platform is being
moved to devicetree.
Fixes: 9be5f3e92e ("MIPS: ingenic: Initial JZ4770 support")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.16
Patchwork: https://patchwork.linux-mips.org/patch/18957/
Signed-off-by: James Hogan <jhogan@kernel.org>
Now that we have support for JZ480 SoCs in the MMC driver,
let's enable it on the devicetree.
Acked-by: James Hogan <jhogan@kernel.org>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add the devicetree node to support the MMC host controller
available in JZ480 SoCs.
Acked-by: James Hogan <jhogan@kernel.org>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add the devicetree node to support the DMA controller found
in JZ480 SoCs.
Tested-by: Mathieu Malaterre <malat@debian.org>
Acked-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for removing some of the MIPS compiler intrinsics from
arch/mips/lib, first update the build of vmlinuz to use the generic
ashldi3 from lib.
Both ashldi3 and bswapsi objects need to be built with different CFLAGS
for inclusion to vmlinuz rather than simply including the object built
for the main kernel image. The objects cannot be built directly from
source, since CONFIG_MODVERSIONS changes cmd_cc_o_c to prevent this.
Split the rule to ship ashldi3 and bswapsi from the relevant source
locations.
These files make no reference to other files in their directory, so the
additional CFLAGS are apparently unnecessary - remove them as well.
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Antony Pavlov <antonynpavlov@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/19050/
[jhogan@kernel.org: Add if_changed and FORCE to fix build failure when
arch/mips/boot/compressed/ashldi3.c is already generated but there is
no .ashldi3.c.cmd file yet]
Signed-off-by: James Hogan <jhogan@kernel.org>
arch/mips/boot/dts/Makefile collects objects from sub-directories into
built-in.a only when CONFIG_BUILTIN_DTB is enabled. Reflect it also to
the sub-directory Makefiles. This suppresses unneeded built-in.a
creation in arch/mips/boot/dts/*/ directories.
While I am here, I replaced $(patsubst %.dtb, %.dtb.o, $(dtb-y)) with
$(addsuffix .o, $(dtb-y)) to simplify the code a little bit.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/19099/
Signed-off-by: James Hogan <jhogan@kernel.org>
These are the main MIPS changes for 4.17. Rough overview:
(1) generic platform: Add support for Microsemi Ocelot SoCs
(2) crypto: Add CRC32 and CRC32C HW acceleration module
(3) Various cleanups and misc improvements
Miscellaneous:
- Hang more efficiently on halt/powerdown/restart
- pm-cps: Block system suspend when a JTAG probe is present
- Expand make help text for generic defconfigs
- Refactor handling of legacy defconfigs
- Determine the entry point from the ELF file header to fix microMIPS
for certain toolchains
- Introduce isa-rev.h for MIPS_ISA_REV and use to simplify other code
Minor cleanups:
- DTS: boston/ci20: Unit name cleanups and correction
- kdump: Make the default for PHYSICAL_START always 64-bit
- Constify gpio_led in Alchemy, AR7, and TXX9
- Silence a couple of W=1 warnings
- Remove duplicate includes
Platform support:
ath79:
- Fix AR724X_PLL_REG_PCIE_CONFIG offset
BCM47xx:
- FIRMWARE: Use mac_pton() for MAC address parsing
- Add Luxul XAP1500/XWR1750 WiFi LEDs
- Use standard reset button for Luxul XWR-1750
BMIPS:
- Enable CONFIG_BRCMSTB_PM in bmips_stb_defconfig for build coverage
- Add STB PM, wake-up timer, watchdog DT nodes
Generic platform:
- Add support for Microsemi Ocelot
- dt-bindings: Add vendor prefix for Microsemi Corporation
- dt-bindings: Add bindings for Microsemi SoCs
- Add ocelot SoC & PCB123 board DTS files
- MAINTAINERS: Add entry for Microsemi MIPS SoCs
- Enable crc32-mips on r6 configs
Octeon:
- Drop '.' after newlines in printk calls
ralink:
- pci-mt7621: Enable PCIe on MT7688
-----BEGIN PGP SIGNATURE-----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=4vUc
-----END PGP SIGNATURE-----
Merge tag 'mips_4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips
Pull MIPS updates from James Hogan:
"These are the main MIPS changes for 4.17. Rough overview:
(1) generic platform: Add support for Microsemi Ocelot SoCs
(2) crypto: Add CRC32 and CRC32C HW acceleration module
(3) Various cleanups and misc improvements
More detailed summary:
Miscellaneous:
- hang more efficiently on halt/powerdown/restart
- pm-cps: Block system suspend when a JTAG probe is present
- expand make help text for generic defconfigs
- refactor handling of legacy defconfigs
- determine the entry point from the ELF file header to fix microMIPS
for certain toolchains
- introduce isa-rev.h for MIPS_ISA_REV and use to simplify other code
Minor cleanups:
- DTS: boston/ci20: Unit name cleanups and correction
- kdump: Make the default for PHYSICAL_START always 64-bit
- constify gpio_led in Alchemy, AR7, and TXX9
- silence a couple of W=1 warnings
- remove duplicate includes
Platform support:
Generic platform:
- add support for Microsemi Ocelot
- dt-bindings: Add vendor prefix for Microsemi Corporation
- dt-bindings: Add bindings for Microsemi SoCs
- add ocelot SoC & PCB123 board DTS files
- MAINTAINERS: Add entry for Microsemi MIPS SoCs
- enable crc32-mips on r6 configs
ath79:
- fix AR724X_PLL_REG_PCIE_CONFIG offset
BCM47xx:
- firmware: Use mac_pton() for MAC address parsing
- add Luxul XAP1500/XWR1750 WiFi LEDs
- use standard reset button for Luxul XWR-1750
BMIPS:
- enable CONFIG_BRCMSTB_PM in bmips_stb_defconfig for build coverage
- add STB PM, wake-up timer, watchdog DT nodes
Octeon:
- drop '.' after newlines in printk calls
ralink:
- pci-mt7621: Enable PCIe on MT7688"
* tag 'mips_4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips: (37 commits)
MIPS: BCM47XX: Use standard reset button for Luxul XWR-1750
MIPS: BCM47XX: Add Luxul XAP1500/XWR1750 WiFi LEDs
MIPS: Make the default for PHYSICAL_START always 64-bit
MIPS: Use the entry point from the ELF file header
MAINTAINERS: Add entry for Microsemi MIPS SoCs
MIPS: generic: Add support for Microsemi Ocelot
MIPS: mscc: Add ocelot PCB123 device tree
MIPS: mscc: Add ocelot dtsi
dt-bindings: mips: Add bindings for Microsemi SoCs
dt-bindings: Add vendor prefix for Microsemi Corporation
MIPS: ath79: Fix AR724X_PLL_REG_PCIE_CONFIG offset
MIPS: pci-mt7620: Enable PCIe on MT7688
MIPS: pm-cps: Block system suspend when a JTAG probe is present
MIPS: VDSO: Replace __mips_isa_rev with MIPS_ISA_REV
MIPS: BPF: Replace __mips_isa_rev with MIPS_ISA_REV
MIPS: cpu-features.h: Replace __mips_isa_rev with MIPS_ISA_REV
MIPS: Introduce isa-rev.h to define MIPS_ISA_REV
MIPS: Hang more efficiently on halt/powerdown/restart
FIRMWARE: bcm47xx_nvram: Replace mac address parsing
MIPS: BMIPS: Add Broadcom STB watchdog nodes
...
Huacai Chen
Jiaxun Yang
Paul Cercueil
周琰杰 (Zhou Yanjie)
David S. Miller
João H. Spies
Quentin Schulz
Tiezhu Yang
Oleksij Rempel
Lars Povlsen
H. Nikolaus Schaller
PrasannaKumar Muralidharan
Linus Torvalds
Masahiro Yamada
Alex Smith
Kamal Dasu
Alexander Lobakin
Reto Schneider
Jouni Hogander
Alexandre GRIVEAUX
Stefan Roese
Masahiro Yamada
Antoine Tenart
Paul Burton
Jonas Gorski
Kevin Darbyshire-Bryant
Thomas Gleixner
Horatiu Vultur
Aaro Koskinen
Zhou Yanjie
Songjun Wu
Alexandre Belloni
Alban Bedel
Mathieu Malaterre
Alexander Sverdlin
Thomas Bogendoerfer
Ezequiel Garcia
Matt Redfearn