The commit df59fa7f4b "spi: orion: support armada extended baud
rates" was too optimistic for the maximum baud rate that the Armada
SoCs can support. According to the hardware datasheet the maximum
frequency supported by the Armada 370 SoC is tclk/4. But for the
Armada XP, Armada 38x and Armada 39x SoCs the limitation is 50MHz and
for the Armada 375 it is tclk/15.
Currently the armada-370-spi compatible is only used by the Armada 370
and the Armada XP device tree. On Armada 370, tclk cannot be higher
than 200MHz. In order to be able to handle both SoCs, we can take the
minimum of 50MHz and tclk/4.
A proper solution is adding a compatible string for each SoC, but it
can't be done as a fix for compatibility reason (we can't modify
device tree that have been already released) and it will be part of a
separate patch.
Fixes: df59fa7f4b (spi: orion: support armada extended baud rates)
Reported-by: Kostya Porotchkin <kostap@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
If a valid GPIO is specified but cannot be requested by the driver, print a
message and error out of omap2_mcspi_setup.
Signed-off-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The OMAP2_MCSPI_CHCONF_FORCE must be toggled even when using GPIO
chip selects. This patch conditionally calls the omap2_mcspi_set_cs
function to do so when using GPIO chip selects.
Signed-off-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The core spi driver swaps the polarity of the enable based on SPI_CS_HIGH.
The omap2 controller has an internal configuration register bit called
OMAP2_MCSPI_CHCONF_EPOL to handle active high chip selects as well.
So we have to revert swap the polarity back for the correct setting of the
OMAP2_MCSPI_CHCONF_FORCE bit in omap2_mcspi_set_cs.
Signed-off-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The core spi driver handles the delay between transactions.
This is a remanant from the transfer_one conversion.
Signed-off-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Incorrect condition is used in spin_event_timeout(). When the TX is
done, the SPIE_NF bit in ESPI_SPIE register is set to 1 to indicate the
Tx FIFO is not full. If the bit is 0, it indicates the Tx FIFO is full.
Due to this error, if the Tx FIFO is full at the beginning, but becomes
not full after handling the Rx FIFO (the SPIE_NF bit is set), the
spin_event_timeout() returns with timeout occurred. It causes the
interrupt handler not to send completion notification to the thread that
called wait_for_complete() waiting for the notification.
Signed-off-by: Jane Wan <Jane.Wan@gainspeed.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI chip select signal need to keep asserted between several
spi_transfer in the same spi_message usually.
But the driver will de-assert CS signal and the assert it between
serval spi_transfer in the same spi_message under some condiations.
This patch fix the bug.
Here is an example:
Assume you have two variables like the following,
struct spi_transfer a;
struct spi_transfer b;
if you send a spi_message only includes 'a' first,
and then you send a spi_message includes 'a' and 'b'
but without resetting 'a'.
Driver will de-assert CS and then assert CS between 'a' and 'b'.
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
USP is a general purpose serial port in SiRFSoC, which can work as SPI.
the most data flow of USP and pure SPI is same with main differences
in registers layout.
this patch moves registers layout to private data, and use flags to
differentiate other minor differences between prima2-spi, prima2-usp
and atlas7-usp for hardware configuration.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
GPIO chip select patch series appears to have broken the native chip select
support. This patch pulls the manual native chip select toggling out of
the transfer_one routine and adds a set_cs routine.
Tested natively on AM3354 with SPI serial flash on spi0cs0.
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Michael Welling <mwelling@ieee.org>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
fixes several warnings/error emmitted by the kbuild system:
* warn: cast from pointer to integer of different size
using size_t instead of u32
* error: 'SZ_4K' undeclared
moved to PAGE_SIZE and PAGE_MASK instead
Review showed also a typo in the same code where tx_buff
was checked twice instead of checking both rx and tx_buff.
Reported by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Conditions per spi_transfer are:
* transfer.len >= 96 bytes (to avoid mapping overhead costs)
* transfer.len < 65536 bytes (limitaion by spi-hw block - could get extended)
* an individual scatter/gather transfer length must be a multiple of 4
for anything but the last transfer - spi-hw block limit.
(some shortcut has been taken in can_dma to avoid unnecessary mapping of
pages which, for which there is a chance that there is a split with a
transfer length not a multiple of 4)
If it becomes a necessity these restrictions can get removed by additional
code.
Note that this patch requires a patch to dma-bcm2835.c by Noralf to
enable scatter-gather mode inside the dmaengine, which has not been
merged yet.
That is why no patch to arch/arm/boot/dts/bcm2835.dtsi is included - the
code works as before without dma when tx/rx are not set, but it writes
a message warning about dma not used:
spi-bcm2835 20204000.spi: no tx-dma configuration found - not using dma mode
To enable dma-mode add the following lines to the device-tree:
dmas = <&dma 6>, <&dma 7>;
dma-names = "tx", "rx";
Tested-by: Noralf Trønnes <noralf@tronnes.org> (private communication)
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix a race (with some kernel configurations) where a queued
master->pump_messages runs and frees dummy_tx/rx before
spi_unmap_msg is running (or is finished).
This results in the following messages:
BUG: Bad page state in process
page:db7ba030 count:0 mapcount:0 mapping: (null) index:0x0
flags: 0x200(arch_1)
page dumped because: PAGE_FLAGS_CHECK_AT_PREP flag set
...
Reported-by: Noralf Trønnes <noralf@tronnes.org>
Suggested-by: Noralf Trønnes <noralf@tronnes.org>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
A few driver fixes plus two changes for the core, one to make the
setup_transfer() callback optional which fixes crashes in some drivers
which were updated to use new interfaces without apparent testing and
one to ensure we don't expose the data buffers we use for dummy
transfers to drivers which avoids potential issues with multiple
accesses to them or reuse.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVO2WTAAoJECTWi3JdVIfQ19wH/2c3NnRGoj5Oz6ltE2Yv2fXd
MZJa/pmb7rUsxB7lwffnmOZj2XZucYg05hChdYnAIV5NtwZlf2xd+s7/kWbhTOdJ
YeFdENjODrfnfBI4Ka82T2wIjFi1KEIDYMY5SyotGRdgl7NyK2atjna/2j/iAggm
PJljJOzzibHGx8tvQcLGNDOeoHXLzUTBg4bOcESTs63447+bn4UQgKVolEC6FY4f
d61T7NVbdWUpwInsj5lFmjkl/w02N5WHNrpChE+AbBk++rBbE2TrJxuRUF2DstVF
LLT5LKGygZVuTjshnlJwMYKT3m3s9qeSGUJJ5u2NIfLe0L2dp/1pZV84OOPFiN4=
=c+gA
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.1-rc1' into spi-linus
spi: Fixes for v4.1
A few driver fixes plus two changes for the core, one to make the
setup_transfer() callback optional which fixes crashes in some drivers
which were updated to use new interfaces without apparent testing and
one to ensure we don't expose the data buffers we use for dummy
transfers to drivers which avoids potential issues with multiple
accesses to them or reuse.
# gpg: Signature made Sat 25 Apr 2015 10:59:47 BST using RSA key ID 5D5487D0
# gpg: key CD7BEEBC: no public key for trusted key - skipped
# gpg: key CD7BEEBC marked as ultimately trusted
# gpg: key AF88CD16: no public key for trusted key - skipped
# gpg: key AF88CD16 marked as ultimately trusted
# gpg: key 16005C11: no public key for trusted key - skipped
# gpg: key 16005C11 marked as ultimately trusted
# gpg: key 5621E907: no public key for trusted key - skipped
# gpg: key 5621E907 marked as ultimately trusted
# gpg: key 5C6153AD: no public key for trusted key - skipped
# gpg: key 5C6153AD marked as ultimately trusted
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
Remove unneeded variable used to store return value.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/returnvar.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If GPIO chip select is specified, request the GPIO in the setup function
and release it in the cleanup function.
Signed-off-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Switches from transfer_one_message to transfer_one to prepare driver for
use of GPIO chip selects.
Signed-off-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
To reduce indentation and complexity of code, insteeds of returning zero
the function rspi_dma_check_then_transfer should return rspi_dma_transfer
directly after checking error.
Signed-off-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
move spi controller's gpio request work out from probe() to spi device
register stage, so after spi device register spi controller can deactive
device's gpio chipselect. old code can't do it because gpio request has
not be done until device register is finised in spi_bitbang_start.
and add cleanup function to free CS gpio.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
I got following error on CONFIG_GPIOLIB=n.
drivers/spi/spi-bcm2835.c: In function 'chip_match_name':
drivers/spi/spi-bcm2835.c:356:21: error: dereferencing pointer to incomplete type 'struct gpio_chip'
return !strcmp(chip->label, data);
^
drivers/spi/spi-bcm2835.c: In function 'bcm2835_spi_setup':
drivers/spi/spi-bcm2835.c:382:9: error: implicit declaration of function 'gpiochip_find' [-Werror=implicit-function-declaration]
chip = gpiochip_find("pinctrl-bcm2835", chip_match_name);
^
drivers/spi/spi-bcm2835.c:382:7: warning: assignment makes pointer from integer without a cast [-Wint-conversion]
chip = gpiochip_find("pinctrl-bcm2835", chip_match_name);
^
drivers/spi/spi-bcm2835.c: In function 'chip_match_name':
drivers/spi/spi-bcm2835.c:357:1: warning: control reaches end of non-void function [-Wreturn-type]
}
^
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
return error for unsupported bits-per-word format, BUG() is not right
for this scenerios as we are not an ASSERT but an error handler.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <baohua.song@csr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The polling mode of the driver is designed for transfers that run
less than 30us - it will only execute under those circumstances.
So it should run comfortably without getting interrupted by the
scheduler.
But there are situations where the raspberry pi is so overloaded
that it can take up to 80 jiffies until the polling thread gets
rescheduled - this has been observed especially under heavy
IO situations.
In such a situation we now fall back to the interrupt handler and
log the situation at debug level.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The way that the timeout code is written in the polling function
the timeout does also trigger when interrupted or rescheduled while
in the polling loop.
This patch changes the timeout from effectively 20ms (=2 jiffies) to
1 second and removes the time that the transfer really takes out of
the computation, as - per design - this is <30us and the jiffie resolution
is 10ms so that does not make any difference what so ever.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The internal chip select CS0 wasn't initialized properly to work with
CS HIGH chips.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Clocks should be prepared and unprepared, fix this by using
clk_prepare_enable() and clk_disable_unprepare() instead of
clk_enable() and clk_disable().
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the OF node of the spi controller and use the generic GPIO based
chip select instead of the custom controller data. As the controller
data isn't used by any board just drop it.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch makes possible for protocol drivers to do full-duplex SPI
transfers properly. Until now this driver could only be used for
half-duplex transfers, since it always expected an spi_transfer with
non-null tx_buf to be only used for TX, and those with non-null rx_buf
to be only used for RX.
The fix consists in correcting the fsl_espi_transfer length by taking
into consideration duplex spi_transfers, and not just by adding n_tx
and n_rx.
Furthermore, this correction has exposed an inconsistency in the
protocol driver <-> controller driver interaction. The spi-fsl-espi
driver artificially inserts TX bytes when message fragmentation is
necessary (due to SPCOM_TRANLEN_MAX) instead of informing the
protocol driver of the hardware limitation. This was tested with the
m25p80 NOR flash protocol driver. Since fixing this issue may cause
other client drivers to malfunction, it was left as is.
Signed-off-by: Jonatas Rech <jonatas.rech@datacom.ind.br>
Signed-off-by: Mark Brown <broonie@kernel.org>
devm_ioremap_resource() doesn't return NULL but an ERR_PTR on error.
Reported-by: Jonas Gorsky <jogo@openwrt.org>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
LS1021A chip also has the DSPI module.
Add it to the dependence.
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is unnecessary for DSPI to enable/disable clk when access DSPI register.
And it will reduce efficiency.
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi queue waits forever for spi_finalize_current_message() to be
called, blocking the bus. Ensure that all error paths from
omap2_mcspi_transfer_one_message() call spi_finalize_current_message().
Signed-off-by: Fionn Cleary <fionn.cleary@streamunlimited.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This has the benefit that the "optimization" of the framework in regards
to spi_sync will also benefit spidev users directly and allow running
spi transfers without a necessary context-switch to message-pump.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
On CPM2, the SPI parameter RAM is dynamically allocated in the
dualport RAM whereas in CPM1, it is statically allocated to a default
address with capability to relocate it somewhere else via the use of
CPM micropatch. The address of the parameter RAM is given by the boot
loader and expected to be mapped via devm_ioremap_resource()
In the current implementation, in function fsl_spi_cpm_get_pram()
there is a confusion between the SPI_BASE register and the base of the
SPI parameter RAM. Fortunatly, it is working properly with MPC866 and
MPC885 because they do set SPI_BASE, but on MPC860 and other old
MPC8xx that doesn't set SPI_BASE, pram_ofs is not properly set.
Also, the parameter RAM is not properly mapped with
devm_ioremap_resource() as it should but still gets accessible by
chance through the full RAM which is mapped from somewhere else.
This patch applies to the SPI driver the same principle as for the
CPM UART: when the CPM is of type CPM1, we simply do an
devm_ioremap_resource() of the area provided via the device tree.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
As it turns out, the set_cs() enable parameter refers to the logic level
on the CS pin, not the state of chip selection.
This broke functionality of the LEDs behind the CPLD, or at least delayed
the commands until another one came in to toggle CS.
Signed-off-by: Bert Vermeulen <bert@biot.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver mediates access between the connected CPLD and other devices
on the bus.
The m25p80-compatible boot flash and (some models) MMC use regular SPI,
bitbanged as required by the SoC. However the SPI-connected CPLD has
a two-wire mode, in which two bits are transferred per SPI clock
cycle. The second bit is transmitted with the SoC's CS2 pin.
Signed-off-by: Bert Vermeulen <bert@biot.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some controller drivers have no need of this callback (spi-altera even
causes a NULL pointer dereference because it doesn't register the callback,
falsely assuming that it is already optional).
Fixes: 30af9b558a ("spi/bitbang: Drop empty setup() functions")
Signed-off-by: Pelle Nilsson <per.nilsson@xelmo.com>
Reviewed-by: Ezequiel Garcia <ezequiel.garcia@vanguardiasur.com.ar>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some spi device drivers use the same tx_buf and rx_buf repeatly for better
performance such as driver/input/touchsreen/ads7846.c, but spi core grab tx_buf
/rx_buf of transfer and set them as dummy_tx/dummy_rx once they are NULL. Thus,
in the second time the tx_buf/rx_buf will be replaced by dummy_tx/dummy_rx and
the data which produced by the last tx or rx may be wrongly sent to the device
or handled by the upper level protocol. This patch just keep the orignal value
of tx_buf/rx_buf if they are NULL after this transfer processed.
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The way that the timeout code is written in the polling function
the timeout does also trigger when interrupted or rescheduled while
in the polling loop.
This patch changes the timeout from effectively 20ms (=2 jiffies) to
1 second and removes the time that the transfer really takes out of
the computation, as - per design - this is <30us and the jiffie resolution
is 10ms so that does not make any difference what so ever.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix:
drivers/spi/spi-bcm2835.c: In function 'chip_match_name':
drivers/spi/spi-bcm2835.c:356:21: error:
dereferencing pointer to incomplete type
drivers/spi/spi-bcm2835.c: In function 'bcm2835_spi_setup':
drivers/spi/spi-bcm2835.c:382:2: error:
` implicit declaration of function 'gpiochip_find'
drivers/spi/spi-bcm2835.c:387:21: error:
dereferencing pointer to incomplete type
by adding the now mandatory GPIOLIB dependency.
Fixes: a30a555d74 ("spi: bcm2835: transform native-cs to gpio-cs
on first spi_setup")
Cc: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
In cases of short transfer times the CPU is spending lots of time
in the interrupt handler and scheduler to reschedule the worker thread.
Measurements show that we have times where it takes 29.32us to between
the last clock change and the time that the worker-thread is running again
returning from wait_for_completion_timeout().
During this time the interrupt-handler is running calling complete()
and then also the scheduler is rescheduling the worker thread.
This time can vary depending on how much of the code is still in
CPU-caches, when there is a burst of spi transfers the subsequent delays
are in the order of 25us, so the value of 30us seems reasonable.
With polling the whole transfer of 4 bytes at 10MHz finishes after 6.16us
(CS down to up) with the real transfer (clock running) taking 3.56us.
So the efficiency has much improved and is also freeing CPU cycles,
reducing interrupts and context switches.
Because of the above 30us seems to be a reasonable limit for polling.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Transforms the bcm-2835 native SPI-chip select to their gpio-cs equivalent.
This allows for some support of some optimizations that are not
possible due to HW-gliches on the CS line - especially filling
the FIFO before enabling SPI interrupts (by writing to CS register)
while the transfer is already in progress (See commit: e3a2be3030)
This patch also works arround some issues in bcm2835-pinctrl which does not
set the value when setting the GPIO as output - it just sets up output and
(typically) leaves the GPIO as low. When a fix for this is merged then this
gpio_set_value can get removed from bcm2835_spi_setup.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the CONTINUE bit is set, the interrupt status we are polling to
identify if a transaction has finished can be sporadic. Even though
the transfer has finished, the interrupt status may erroneously
indicate that there is still data in the FIFO. This behaviour causes
random timeouts in large PIO transfers.
Instead of using the CONTINUE bit to control the CS lines, use the SPI
core's CS GPIO handling. Also, now that the CONTINUE bit is not being
used, we can poll for the ALLDONE interrupt to indicate transfer
completion.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Imagination has recommended that the SPFI controller be reset after
each message, regardless of success or failure. Do this in an
unprepare_message() callback.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver can be greatly simplified by moving the transfer timeout
handling to a handle_err() callback.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Setting the transfer length in the TRANSACTION register after the
CONTROL register is programmed causes intermittent timeout issues in
SPFI transfers when using the SPI framework to control the CS GPIO
lines. To avoid this issue, set transfer length before programming
the CONTROL register.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If a driver doesn't implement the master->handle_err() callback and an
SPI transfer fails, the kernel will crash with a NULL pointer
dereference:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0003000
[00000000] *pgd=80000040004003, *pmd=00000000
Internal error: Oops: 80000206 [#1] SMP ARM
Modules linked in:
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 4.0.0-rc7-koelsch-05861-g1fc9fdd4add4f783 #1046
Hardware name: Generic R8A7791 (Flattened Device Tree)
task: eec359c0 ti: eec54000 task.ti: eec54000
PC is at 0x0
LR is at spi_transfer_one_message+0x1cc/0x1f0
Make the master->handle_err() callback optional to avoid the crash.
Also fix a spelling mistake in the callback documentation while we're at
it.
Fixes: b716c4ffc6 ("spi: introduce master->handle_err() callback")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Although the SPFI BITCLK divider supports a value of up to 255, only
values up to 128 are usable. This results in a maximum possible bit
clock rate of 1/4th the input clock rate.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation for switching to using the SPI core's CS GPIO handling,
move setup of the PORT_STATE register, which must be configured before
CS is asserted, to a prepare_message() callback.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add delay between chip select and clock signals, before clock starts and
after clock stops.
Signed-off-by: Aaron Brice <aaron.brice@datasoft.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Previous algorithm had an outer loop with the values {2,3,5,7} and an
inner loop with {2,4,6,8,16,32,...,32768}, and would pick the first
value over the required scaling value (where the total scale was the two
numbers multiplied).
Since the inner loop went up to 32768 it would always pick a value of 2
for PBR and a much higher than necessary value for BR. The desired
scale factor was being divided by two I believe to compensate for the
much higher scale factors (the divide by two not specified in the
reference manual).
Updated to check all values and find the smallest scale factor possible
without going over the desired clock rate.
Signed-off-by: Aaron Brice <aaron.brice@datasoft.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need "ret" to be unsigned for the error handling to work. The
signedness of "i" and "n" don't matter but qspi_set_send_trigger()
returns an int so I've changed them to int as well.
Fixes: 4b6fe3edcb ('spi: Using Trigger number to transmit/receive data')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
They are used to decide if the controller can do DMA on a buffer
of a specific length and thus are needed before any transfer is attempted.
This fixes a memory leak where the SPI core uses the drivers can_dma()
callback to determine if a buffer needs to be mapped. As the watermark
levels aren't correct at that point the driver falsely claims to be able to
DMA the buffer when it fact it isn't.
After the transfer has been done the core uses the same callback to
determine if it needs to unmap the buffers. As the driver now correctly
claims to not being able to DMA the buffer the core doesn't attempt to
unmap the buffer which leaves the SGT leaking.
Fixes: f62caccd12 (spi: spi-imx: add DMA support)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
cr_width may be not initialized before using by cr, the related warning
(with defconfig under blackfin by gcc5):
CC drivers/spi/spi-bfin5xx.o
drivers/spi/spi-bfin5xx.c: In function 'bfin_spi_pump_transfers':
drivers/spi/spi-bfin5xx.c:655:5: warning: 'cr_width' may be used uninitialized in this function [-Wmaybe-uninitialized]
cr |= cr_width;
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current implementation of bitbang_txrx_be_cpha0 and
bitbang_txrx_be_cpha1 always call setmosi. That runs into several
unnecessary calls into the gpiolib when the level of the GPIO actually
has not to be changed.
This patch changes the routines to remember the last GPIO level
and only calls setmosi if an change has to be made. This
way it improves the transfer throughput.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
We refactored this code but accidentally left out a break statement so
QUARK_X1000_SSP isn't handled correctly.
Fixes: 025ffe88ee ('spi: pxa2xx: shift clk_div in one place')
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Previous algorithm had an outer loop with the values {2,3,5,7} and an
inner loop with {2,4,6,8,16,32,...,32768}, and would pick the first
value over the required scaling value (where the total scale was the two
numbers multiplied).
Since the inner loop went up to 32768 it would always pick a value of 2
for PBR and a much higher than necessary value for BR. The desired
scale factor was being divided by two I believe to compensate for the
much higher scale factors (the divide by two not specified in the
reference manual).
Updated to check all values and find the smallest scale factor possible
without going over the desired clock rate.
Signed-off-by: Aaron Brice <aaron.brice@datasoft.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to transmit and receive data when have 32 bytes of data that
ready has prepared on Transmit/Receive Buffer to transmit or receive.
Instead transmits/receives a byte data using Transmit/Receive Buffer
Data Triggering Number will improve the speed of transfer data.
Signed-off-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
To reduce the number of interrupts/message we fill the FIFO before
enabling interrupts - for short messages this reduces the interrupt count
from 2 to 1 interrupt.
There have been rare cases where short (<200ns) chip-select switches with
native CS have been observed during such operation, this is why this
optimization is only enabled for GPIO-CS.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Tested-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since spidev is a detail of how Linux controls a device rather than a
description of the hardware in the system we should never have a node
described as "spidev" in DT, any SPI device could be a spidev so this
is just not a useful description.
In order to help prevent users from writing such device trees generate a
warning if spidev is instantiated as a DT node without an ID in the match
table.
Signed-off-by: Mark Brown <broonie@kernel.org>
This also allows for GPIO-CS to get used removing the limitation of
2/3 SPI devises on the SPI bus.
Fixes: spi-cs-high with native CS with multiple devices on the spi-bus
resetting the chip selects to "normal" polarity after a finished
transfer.
No other functionality/improvements added.
Tested with the following 4 devices on the spi-bus:
* mcp2515 with native CS
* mcp2515 with gpio CS
* fb_st7735r with native CS
(plus spi-cs-high via transistor inverting polarity)
* enc28j60 with gpio-CS
Tested-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We have found that we can sometimes see read failures on boards with
high-capacitance SPI lines. It seems that the controller samples the Rx
data line too early, and its register interface has an "Rx Sample Delay"
setting to fine-tune against this issue.
This patch adds a new optional device tree entry that can configure this
delay in terms of nanoseconds. The kernel will calculate the
best-fitting amount of parent clock ticks to program the controller with
based on that.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Rockchip SPI driver currently calculates its clock rate divisor by
integer dividing the parent rate by the target rate, and then rounding
the result up to the next even number (since the divisor must be
even).
Clock rate divisors should always be rounded up, so that the resulting
frequency is lower or equal to the target. This is correctly done in the
second step here but not in the first, so we still have a risk of
exceeding the desired target frequency (e.g. setting spi-max-frequency
to 40000000 with a parent clock of 99000000 could lead to a divisor of
99000000 / 40000000 == 2 (which is even) that then results in an
effective frequency of 99000000 / 2 == 49500000 (potentially exceeding
the flash chip's specifications).
This patch changes the division to round up to fix this problem.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Trying to register an SPI device asynchronously (via async_schedule() call)
results in an ugly complaint from request_module() warning about potential
deadlock (because request_module tries to wait for async works to
complete, the caller is also an async work in this case).
While we could try to switch to using request_module_nowait(), other buses,
as well as SPI itself when not using device tree, do not try to load
modules explicitly, but rather rely on the standard infrastructure (such as
udev) to execute module loading. There is no reason why SPI OF-described
devices should be treated differently.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The commit 1a7b7ee72c (spi: Ensure that CS line is in non-active state after
spi_setup()) introduces an unconditional call of spi_set_cs() before ->setup().
The dw_spi_set_cs() relies on that fact that ->setup() is already called, but
it doesn't now. This patch fixes the crash by adding an additional check to
dw_spi_set_cs().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Quark SoC data sheet describes the baud rate setting using fractional
divider. The subset of possible values represented by a table suggests that the
divisor has one block that could divide by 5. This explains the number of the
beast in some cases in the table. Thus, in this particular case the divisor can
be evaluated as
5^i * 2^j * 2 * k,
where
i = [0, 1]
j = [0, 23]
k = [1, 256]
There are few cases as mentioned in the data sheet, i.e. better form of the
clock signal will be in case if DDS_CLK_RATE either 2^n or 2/5. It's also
possible to use any value that is less or equal to 0x33333 (1/5/16 = 1/80).
All three cases are compared to each other and the one that suits better is
chosen by the approximation algorithm. Anyone can play with the script [1] that
represents the algorithm.
[1] https://gist.github.com/06b084488b3629898121
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch refactors ssp_get_clk_div() and pxa2xx_ssp_get_clk_div() to align
clk_div calculations, i.e. ssp_get_clk_div() and quark_x1000_set_clk_regvals()
will return plain clk_div and it will be shifted to proper position in
pxa2xx_ssp_get_clk_div().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
`spidev_message()` sums the lengths of the individual SPI transfers to
determine the overall SPI message length. It restricts the total
length, returning an error if too long, but it does not check for
arithmetic overflow. For example, if the SPI message consisted of two
transfers and the first has a length of 10 and the second has a length
of (__u32)(-1), the total length would be seen as 9, even though the
second transfer is actually very long. If the second transfer specifies
a null `rx_buf` and a non-null `tx_buf`, the `copy_from_user()` could
overrun the spidev's pre-allocated tx buffer before it reaches an
invalid user memory address. Fix it by checking that neither the total
nor the individual transfer lengths exceed the maximum allowed value.
Thanks to Dan Carpenter for reporting the potential integer overflow.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The official documentation is wrong in this respect.
Has been tested empirically for dividers 2-1024
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Implement the recommendation from the BCM2835 data-sheet
with regards to polling drivers to fill/drain the FIFO as much data as possible
also for the interrupt-driven case (which this driver is making use of).
This means that for long transfers (>64bytes) we need one interrupt
every 64 bytes instead of every 12 bytes, as the FIFO is 16 words (not bytes) wide.
Tested with mcp251x (can bus), fb_st7735 (TFT framebuffer device)
and enc28j60 (ethernet) drivers.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
asm/irq.h is already included by linux/interrupt.h.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These asm/io.h, asm/irq.h and asm/delay.h are needless since they are
already included by linux/io.h via drivers/spi/spi-pxa2xx.h,
linux/interrupt.h and linux/delay.h.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the endian agnositc IO functions instead of the __raw ones for when
the driver is in use on big-endian systems.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The following errors/warnings issued by checkpatch.pl --strict have been fixed:
drivers/spi/spi-bcm2835.c:182: CHECK: Alignment should match open parenthesis
drivers/spi/spi-bcm2835.c:191: CHECK: braces {} should be used on all arms of this statement
drivers/spi/spi-bcm2835.c:234: CHECK: Alignment should match open parenthesis
drivers/spi/spi-bcm2835.c:256: CHECK: Alignment should match open parenthesis
drivers/spi/spi-bcm2835.c:271: CHECK: Alignment should match open parenthesis
drivers/spi/spi-bcm2835.c:346: CHECK: Alignment should match open parenthesis
total: 0 errors, 0 warnings, 6 checks, 403 lines checked
In 2 locations the arguments had to get split/moved to the next line so that the
line width stays below 80 chars.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
With spidev the mesg->complete callback points to spidev_complete.
Calling this unblocks spidev_sync and so spidev_sync_write finishes. As
the struct spi_message just read is a local variable in
spidev_sync_write and recording the trace event accesses this message
the recording is better done first. The same can happen for
spidev_sync_read.
This fixes an oops observed on a 3.14-rt system with spidev activity
after
echo 1 > /sys/kernel/debug/tracing/events/spi/enable
.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Altera's Arria10 SoC interconnect requires a 32-bit write for APB
peripherals. The current spi-dw driver uses 16-bit accesses in
some locations. This patch converts all the 16-bit reads and
writes to 32-bit reads and writes.
Additional Documentation to Support this Change:
The DW_apb_ssi databook states:
"All registers in the DW_apb_ssi are addressed at 32-bit boundaries
to remain consistent with the AHB bus. Where the physical size of
any register is less than 32-bits wide, the upper unused bits of
the 32-bit boundary are reserved. Writing to these bits has no
effect; reading from these bits returns 0." [1]
[1] Section 6.1 of dw_apb_ssi.pdf (version 3.22a)
Request for test with platforms using the DesignWare SPI IP.
Tested On:
Altera CycloneV development kit
Altera Arria10 development kit
Compile tested for build errors on x86_64 (allyesconfigs)
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Reviewed-and-tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the omap100k driver uses prepare and unprepare transfer hardware
to enable and disable clocks for the IP block. Since these functions are
called along with runtime PM and end up duplicating its functionality in a
less flexible fashion we are trying to phase them out so convert this
driver to do runtime PM instead.
While doing so add missing error handling and remove a redundant NULL
assignment.
Signed-off-by: Mark Brown <broonie@kernel.org>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some devices samples state of the chip select signal during power up
and act differently based on this state, so SPI core should ensure
that CS line is driven in non-active state after spi_setup().
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of clearing the RxU, RxO, and TxO IRQs individually with
3 register reads, a single read of the ICR register will do the
same thing.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
intel_mid_dma seems to be unmaintained for a long time. Moreover, the IP block
of DMA itself is the same in both dw_dmac and intel_mid_dma. This patch moves
spi-dw-midpci to use dw_dmac driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI core has a comprehensive function set to map and unmap a message when it's
needed. This patch converts driver to use that advantage.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch shuts up any ongoing DMA transfer in case of error.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In according to documentation SPI in DMA mode may encounter underrun/overrun
failures in rare cases. When such failure occurs, an error recovery protocol is
expected to be implemented in the device driver so that the failed transaction
can be restarted.
This patch enables FIFO overrun / underrun interrupts in DMA case and adds a
handler for that.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch splits DMA preparatory code to dma_setup() callback. The change also
converts transfer_one() to program DMA whenever the transfer is DMA mapped. The
change is a follow up of the converion to use SPI core transfer_one_message().
Since the DMA mapped transfers can be interleaved with PIO ones the DMA related
configuration should respect that.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DMAEngine has a specific type to be used for bus width. This patch converts the
code to use the values of the specific type when configure DMA transfer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove Kconfig dependency and enable driver for
all ARCHs.
Also update help description.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All SPI drivers have been converted from legacy suspend/resume callbacks to
dev_pm_ops. So we can finally remove support for legacy PM from the SPI
core.
Since there aren't any special bus specific things to do during
suspend/resume and since the PM core will automatically fallback directly to
using the device's PM ops if no bus PM ops are specified there is no need to
have any special SPI bus PM ops.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The logic of DMA completion is broken now since test_and_clear_bit() never
returns the other bit is set. It means condition are always false and we have
spi_finalize_current_transfer() called per each DMA completion which is wrong.
The patch fixes logic by clearing BUSY bit first and then check for the other
one.
Fixes: 30c8eb52cc (spi: dw-mid: split rx and tx callbacks when DMA)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This patch adds DMA capabilities to the spi-qup driver. If DMA channels are
present, the QUP will use DMA instead of block mode for transfers to/from SPI
peripherals for transactions larger than the length of a block.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Ivan T. Ivanov <iivanov@mm-sol.com
Signed-off-by: Mark Brown <broonie@kernel.org>
num-cs is 32 bit property, don't read just upper 16 bits.
Fixes: 4a8573abe9 (spi: qup: Remove chip select function)
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This patch removes a lot of duplicate code since SPI core provides a nice
message handling.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch refactors the code in pump_transfers() to reprogram the registers
immediately when we have a new configuration data. The behaviour is slightly
modified:
- chip is always disabled and reenabled
- CTRL0 is always reprogrammed
This change allows to do a further refactoring and simplier conversion to use
SPI core DMA routines in the future.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The error handling is partially broken since the controller is disabled on
error and is not re-enabled until condition occurs, i.e. mode (poll, PIO/DMA),
chip (cs_change), or speed (clk_div) is changed. In the result of these changes
we will have a predictable state of the SPi controller independently on how
successfull was a previous transfer.
The patch disables interrupts and re-enables the SPI controller wherever it
needs to be done. Thus most of the time the SPI controller is kept enabled. The
runtime PM, when it will be implemented, must take care of the controller
disabling and re-enabling.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit fd316941c ("spi/pl022: disable port when unused") introduced a race,
which leads to possible driver lock up (easily reproducible on SMP).
The problem happens in giveback() function where the completion of the transfer
is signalled to SPI subsystem and then the HW SPI controller is disabled. Another
transfer might be setup in between, which brings driver in locked-up state.
Exact event sequence on SMP:
core0 core1
=> pump_transfers()
/* message->state == STATE_DONE */
=> giveback()
=> spi_finalize_current_message()
=> pl022_unprepare_transfer_hardware()
=> pl022_transfer_one_message
=> flush()
=> do_interrupt_dma_transfer()
=> set_up_next_transfer()
/* Enable SSP, turn on interrupts */
writew((readw(SSP_CR1(pl022->virtbase)) |
SSP_CR1_MASK_SSE), SSP_CR1(pl022->virtbase));
...
=> pl022_interrupt_handler()
=> readwriter()
/* disable the SPI/SSP operation */
=> writew((readw(SSP_CR1(pl022->virtbase)) &
(~SSP_CR1_MASK_SSE)), SSP_CR1(pl022->virtbase));
Lockup! SPI controller is disabled and the data will never be received. Whole
SPI subsystem is waiting for transfer ACK and blocked.
So, only signal transfer completion after disabling the controller.
Fixes: fd316941c (spi/pl022: disable port when unused)
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
"flag" variable does nothing, remove it.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
PL022 Programmers model explicitely states "do not modify undefined register
bits". Correct the "all enable" interrupt mask so that it only enables defined
ones.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to PL022 specification, TNF bit states for "Transmit FIFO Not full".
So the logic here is inverted. But "Receive Overrun Interrupt", which is handled
here, is only triggered on Rx errors. So instead of fixing the if statement,
remove the whole message.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There was handle_err() callback introduced that is dedicated for error
handling. The patch moves error handling to this callback.
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This callback would be useful to handle an error that occurs in the generic
implementation of transfer_one_message(). The good candidate for this is to
drain FIFO and / or to terminate DMA transfers when timeout happened.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When DMA descriptor allocation fails we should not try to assign any fields in
the bad descriptor. The patch adds the necessary checks for that.
Fixes: 7063c0d942 (spi/dw_spi: add DMA support)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Removing the udelay between setting and clearing the soft reset bit in
the spfi control register as it is not required.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Maximum transfer length supported by SPFI is 65535, this is limited
by the number of bits available in SPFI TSize register to represent
the transfer size.
For transfer requests larger than the maximum supported the driver
will return an invalid argument error.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The fourth argument of dmaengine_prep_slave_sg needs to be of the
enumeration type dma_transfer_direction instead of dma_data_direction.
Since the used enumeration values actually stay the same, this is not
an actual issue at runtime.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Mark Brown <broonie@kernel.org>
Additionally to the current DMA transfer the PDC allows to set up a next DMA
transfer. This is useful for larger SPI transfers.
The driver currently waits for ENDRX as end of the transfer. But ENDRX is set
when the current DMA transfer is done (RCR = 0), i.e. it doesn't include the
next DMA transfer.
Thus a subsequent SPI transfer could be started although there is currently a
transfer in progress. This can cause invalid accesses to the SPI slave devices
and to SPI transfer errors.
This issue has been observed on a hardware with a M25P128 SPI NOR flash.
So instead of ENDRX we should wait for RXBUFF. This flag is set if there is
no more DMA transfer in progress (RCR = RNCR = 0).
Signed-off-by: Torsten Fleischer <torfl6749@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The commit d297933cc7 (spi: dw: Fix detecting FIFO depth) tries to fix the
logic of the FIFO detection based on the description on the comments. However,
there is a slight difference between numbers in TX Level and TX FIFO size.
So, by specification the FIFO size would be in a range 2-256 bytes. From TX
Level prospective it means we can set threshold in the range 0-(FIFO size - 1)
bytes. Hence there are currently two issues:
a) FIFO size 2 bytes is actually skipped since TX Level is 1 bit and could be
either 0 or 1 byte;
b) FIFO size is incorrectly decreased by 1 which already done by meaning of
TX Level register.
This patch fixes it eventually right.
Fixes: d297933cc7 (spi: dw: Fix detecting FIFO depth)
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Instead of an additional reading from the register let's update it even if the
value is kept the same.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch does the following changes:
a) the calculation of clk_div is simplified to oneliner;
b) chip->clk_div is updated if clk_div is not zero, therefore the condition is
simplified by using chip->clk_div in both cases;
c) while here, the redundant parentheses are removed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to have an additional variable to get a TX level. The patch
refactors this piece of code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no sense to keep a member assignment in the internal structure inside
the condition which reprograms HW. It makes code readability better if kept
outside of the condition.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The commit d58cf5ff65 brought a second controller to the list of supported
devices and changed a number of the chip selects. Besides the previous number
was wrong anyway the mentioned patch makes it wrong again meanwhile has a
proper numbers in the commit message. Indeed, SPI1 has 5 bits and SPI2 has 2
bits, but it does not mean to have power of two of this bits as a possible
number of the chip selects. So, this patch fixes it eventually.
Fixes: d58cf5ff65 (spi: dw-pci: describe Intel MID controllers better)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This patch changes the way space is reserved in spidev's pre-allocated
TX and RX bounce buffers to avoid wasting space in the buffers for an
SPI message consisting of multiple, half-duplex transfers in different
directions.
Background:
spidev data structures have separate, pre-allocated TX and RX bounce
buffers (`spidev->tx_buffer` and `spidev->rx_buffer`) of fixed size
(`bufsiz`). The `SPI_IOC_MESSAGE(N)` ioctl processing uses a kernel
copy of the N `struct spi_ioc_transfer` elements copied from the
userspace ioctl arg pointer. In these elements: `.len` is the length of
transfer in bytes; `.rx_buf` is either a userspace pointer to a buffer
to copy the RX data to or is set to 0 to discard the data; and `.tx_buf`
is either a userspace pointer to TX data supplied by the user or is set
to 0 to transmit zeros for this transfer.
`spidev_message()` uses the array of N `struct spi_ioc_transfer`
elements to construct a kernel SPI message consisting of a `struct
spi_message` containing a linked list (allocated as an array) of N
`struct spi_transfer` elements. This involves iterating through the
`struct spi_ioc_transfer` and `struct spi_transfer` elements (variables
`u_tmp` and `k_tmp` respectively). Before the first iteration,
variables `tx_buf` and `rx_buf` point to the start of the TX and RX
bounce buffers `spidev->tx_buffer` and `spidev->rx_buffer` and variable
`total` is set to 0. These variables keep track of the next available
space in the bounce buffers and the total length of the SPI message.
Each iteration checks that there is enough room left in the buffers for
the transfer. If `u_tmp->rx_buf` is non-zero, `k_tmp->rx_buf` is set to
`rx_buf`, otherwise it remains set to NULL. If `u_tmp->tx_buf` is
non-zero, `k_tmp->tx_buf` is set to `tx_buf` and the userspace TX data
copied there, otherwise it remains set to NULL. The variables `total`,
`rx_buf` and `tx_buf` are advanced by the length of the transfer.
The "problem":
While iterating through the transfers, the local bounce buffer "free
space" pointer variables `tx_buf` and `rx_buf` are always advanced by
the length of the transfer. If `u_tmp->rx_buf` is 0 (so `k_tmp->rx_buf`
is NULL), then `rx_buf` is advanced unnecessarily and that part of
`spidev->rx_buffer` is wasted. Similarly, if `u_tmp->tx_buf` is 0 (so
`k_tmp->tx_buf` is NULL), part of `spidev->tx_buffer` is wasted.
What this patch does:
To avoid wasting space unnecessarily in the RX bounce buffer, only
advance `rx_buf` by the transfer length if `u_tmp->rx_buf` is non-zero.
Similarly, to avoid wasting space unnecessarily in the TX bounce buffer,
only advance `tx_buf` if `u_tmp->tx_buf is non-zero. To avoid pointer
subtraction, use new variables `rx_total` and `tx_total` to keep track
of the amount of space allocated in each of the bounce buffers. If
these exceed the available space, a `-EMSGSIZE` error will be returned.
Limit the total length of the transfers (tracked by variable `total`) to
`INT_MAX` instead of `bufsiz`, returning an `-EMSGSIZE` error if
exceeded. The total length is returned by `spidev_message()` on success
and we want that to be non-negative. The message size limits for the
`SPI_IOC_MESSAGE(N)` ioctl are now as follows:
(a) total length of transfers is <= INTMAX;
(b) total length of transfers with non-NULL rx_buf is <= bufsiz;
(c) total length of transfers with non-NULL tx_buf is <= bufsiz.
Some transfers may have NULL rx_buf and NULL tx_buf.
If the transfer is completed successfully by the SPI core,
`spidev_message()` iterates through the transfers to copy any RX data
from the bounce buffer back to userspace on those transfers where
`u_tmp->rx_buf` is non-zero. The variable `rx_buf` is again used to
keep track of the corresponding positions in the bounce buffer. Now it
is only advanced for those transfers that use the RX bounce buffer.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Exynos 7 arm64 support now allows the S3C64xx SPI driver to be
compiled into an ARM64 kernel, so the cast from the [rt]x_dmach int
variable to a void* in this driver now triggers a warning.
Add a long cast to silence the compiler.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current sh-msiof sets dma_slave_config :: slave_id field for DMAEngine,
but it is no longer needed. Let's remove it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Current rspi sets dma_slave_config :: slave_id field for DMAEngine,
but it is no longer needed. Let's remove it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Data corruption is seen while reading/writing large data from/to qspi
device because the data register is over written or read before data
is ready which is denoted by busy bit in status register. SO adding
a busy bit check before writing/reading data to/from qspi device.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull kconfig updates from Michal Marek:
"Yann E Morin was supposed to take over kconfig maintainership, but
this hasn't happened. So I'm sending a few kconfig patches that I
collected:
- Fix for missing va_end in kconfig
- merge_config.sh displays used if given too few arguments
- s/boolean/bool/ in Kconfig files for consistency, with the plan to
only support bool in the future"
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kconfig: use va_end to match corresponding va_start
merge_config.sh: Display usage if given too few arguments
kconfig: use bool instead of boolean for type definition attributes
Use the normal {} instead of a macro to terminate an array.
Remove the macro too.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently only supports a single device per I2C bus since it uses
the I2C bus number to set the SPI bus number. This makes it impossible to
connect more than one chip to a single I2C bus.
We don't want to use dynamic bus numbers unconditionally since this would
result in every instantiation getting a different bus number starting with
65,535 counting down unless devicetree is configured. If devicetree is
configured, however, the SPI bus number is obtained from devicetree
data. So we can use dynamic SPI bus numbers in this case.
Reported-and-Tested-by: Marco Menchise <marco.menchise@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Converting milliseconds to jiffies by "val * HZ / 1000" is technically
ok but msecs_to_jiffies(val) is the cleaner solution and handles all
corner cases correctly.
This is only an API consolidation and should make things more readable
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
return type of wait_for_completion_timeout is unsigned long not int, this
patch uses the return value of wait_for_completion_timeout in the condition
directly rather than adding a additional appropriately typed variable.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
return type of wait_for_completion_timeout is unsigned long not int, this
patch uses the return value of wait_for_completion_timeout in the condition
directly rather than assigning it to an incorrect type variable.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
return type of wait_for_completion_timeout is unsigned long not int and
always returns >=0 , this patch adds a suitable return variable and
simplifies the return value checking as there is no < 0 case.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
return type of wait_for_completion_timeout is unsigned long not int, this
patch uses the return value of wait_for_completion_timeout in the condition
directly rather than assigning it to an incorrect type variable.
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Mark Brown <broonie@kernel.org>
return type of wait_for_completion_timeout is unsigned long not int, this
patch changes the type of m from int to unsigned long.
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the include of mach/dma.h to the legacy PXA DMA code where it is used.
This enables building spi-pxa2xx on ARM64.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
return type of wait_for_completion_timeout is unsigned long not int, this
patch adds an appropriate variable and fixes up the assignment. It removes
the else branch as the only thing it was doing is assigning ret = 0; - but
ret is never used thereafter so that is not needed. As the string in
dev_err already states "timeout" there is little point in printing the 0.
A typo in "trasfer" -> transfer is also fixed.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For TKT238285 hardware issue which may cause txfifo store data twice can only
be caught on i.mx6dl, we use pio mode instead of DMA mode on i.mx6dl.
Fixes: f62caccd12 (spi: spi-imx: add DMA support)
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Move the check for spi->bits_per_word
before allocation, to avoid memory leak.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sh-msiof of frequency dividing does not perform the calculation, driver have
to manage setting value in the table. It is not possible to set frequency
dividing value close to the actual data in this way. This changes from
frequency dividing of table management to setting by calculation.
This driver is able to set a value close to the actual data.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI_IOC_MESSAGE(n) ioctl commands' argument points to an array of n
struct spi_ioc_transfer elements. The spidev's compat_ioctl handler
just converts this pointer and passes it on to the unlocked_ioctl
handler to process it.
The tx_buf and rx_buf members of struct spi_ioc_transfer are of type
__u64 and hold pointer values. A 32-bit userspace application running
in a 64-bit kernel might not have widened the 32-bit pointers correctly
for the kernel. The application might have sign-extended the pointer to
when the kernel expects it to be zero-extended, or vice versa, leading
to an -EFAULT being returned by spidev_message() if the widened pointer
is invalid.
Handle the SPI_IOC_MESSAGE(n) ioctl commands specially in the
compat_ioctl handler, calling new function spidev_compat_ioctl_message()
to handle them. This processes them in the same way as the
unlocked_ioctl handler except that it uses compat_ptr() to convert the
tx_buf and rx_buf members of each struct spi_ioc_transfer element.
To save code, factor out part of the unlocked_ioctl handler into a new
function spidev_get_ioc_message(). This checks the ioctl command code
is a valid SPI_IOC_MESSAGE(n), determines n and copies the array of n
struct spi_ioc_transfer elements from userspace into dynamically
allocated memory, returning either a pointer to the memory, an
ERR_PTR(-err) value, or NULL (for SPI_IOC_MESSAGE(0)).
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
On 1 and 2 bytes per word, the transfer of the 3 last bytes will access
memory outside tx_ptr.
Although this has not trigger any error on real hardware, we should
better fix this.
Fixes: 24ba5e593f (Remove rx_fn and tx_fn pointer)
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit 99082eab63 since it
breaks the build due to differing implementations of iowrite() and
ioread().
Signed-off-by: Mark Brown <broonie@kernel.org>
The core only supports up to 32 slaves, and the chipselect function
expects the same.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Small transfers generally can be accomplished faster in polling mode.
This patch select the transfer which size is bellow the buffer size to
be done on polling mode
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The variable never leaves the scope of txrx_bufs.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify the code by using the unit used on most of the code logic.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify the code by using the unit used on most of the code logic.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
spi_rx handles the case where the buffer is null. Nevertheless spi_tx
did not handle it, and was handled by the caller function.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify the code by removing the tx and and rx function pointers and
substitute them by a single function.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The core controls the chip select lines individually.
By default, all the lines are consider active_low. After
spi_setup_transfer, it has its real value.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When no irq is used, there is no need to inhibit the transmission for
every transaction. This inhibition was implemented to avoid a race
condition with the irq handler.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The core can run in polling mode. In fact, the performance of the core
is similar (or even better), due to the fact most of the spi
transactions are just a couple of bytes and there is one irq per
transactions.
When an mtd device is connected via spi, reading 8MB of data produces
more than 80K interrupts (with irq disabling, context swith....)
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The control register has not changed since the previous access.
Therefore we can use the cached value and safe one bus access.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On the transmission loop, check for remaining bytes at the loop
condition.
This way we can handle transmissions of 0 bytes and clean the code.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of enabling the IRQ and disabling it for every transaction.
Specially the small transactions (1,2 words) benefit from removing 3 bus
accesses.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of checking the TX_FULL flag for every transaction, find out the
size of the buffer at probe time and use it.
To avoid situations where the core had some data on the buffer before
initialization, the core is reseted before the buffer size is detected
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DSPI module need cs change information in
a spi transfer. According to cs change, DSPI
will give last data the right flag. Bitbang
provide cs change behind the last data in
a transfer. So DSPI can not deal the last
data in every transfer properly, so remove
the bitbang in the driver.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The pl08x driver originally selected S3C64XX_PL080 to avoid having
the legacy Samsung DMA interfaces. Those are now gone, so the
select is no longer needed, but it now causes problems when
CONFIG_DMA_ENGINE is disabled:
arch/arm/plat-samsung/built-in.o: In function `s3c64xx_spi0_set_platdata':
:(.init.text+0x518): undefined reference to `pl08x_filter_id'
This simply removes the 'select' to avoid this problem.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
We currently get a warning about potentially uninitialized variables
in the rockchip spi driver, at least in certain toolchain versions:
spi/spi-rockchip.c: In function 'rockchip_spi_prepare_dma':
include/linux/dmaengine.h:796:2: warning: 'txdesc' may be used uninitialized in this function
include/linux/dmaengine.h:796:2: warning: 'rxdesc' may be used uninitialized in this function
The reason seems to be that gcc cannot know whether the value
of the rs->rx and rs->tx variables change between the two points
these are accessed.
The code is actually correct, but to make this clearer to the
compiler, this changes the conditionals to test for the local
rxdesc/txdesc variables instead, which it knows won't change.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 7566bcc76b ("spi: pxa2xx: Move is_lpss_ssp() tests to caller") did
not check LPSS before calling lpss_ssp_setup() in pxa2xx_spi_resume().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
devm_* API was supposed to be used only in probe function call.
Memory is allocated at 'probe' and free automatically at 'remove'.
Usage of devm_* functions outside probe sometimes leads to memory leak.
Avoid using devm_kzalloc in dspi_setup_transfer and use kzalloc instead.
Also add the dspi_cleanup function to free the controller data upon
cleanup.
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The number of words in the read buffer will be exactly the same as the
number of words written on write buffer, once the transaction has
finished.
Instead of cheking the rx_empty flags for every word simply save the
number of words written by fill_tx_fifo.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The clock information is being kept in the custom register on Intel MID
platforms. Each controller has its own dedicated custom register for that.
Thus, to get a proper frequency we have to read value from the specific offset
to the register block. This patch makes this happen.
Fixes: d58cf5ff65 (spi: dw-pci: describe Intel MID controllers better)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Hardware supports LOOP mode. Support it also in the driver.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Hardware supports LSB_FIRST mode. Support it also in the driver.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This commit adds support for multiple hardware chip selects to spi-orion.
Different SoCs support different number of chip selects (up to
8 on some platforms). The driver allows up to this number, and it is up
to the implementer to only use the chip selects that are available.
Signed-off-by: Ken Wilson <ken.wilson@opengear.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
spi_setup() will test unsupported mode bits before calling spi->master->setup.
Thus remove duplicate code to test unsupported mode bits in spi_st_setup().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This commit changes spi-orion to provide setup, set_cs, and transfer_one
functions instead of transfer_one_message. This allows chip select support
for both native and GPIO chip selects to be added.
Signed-off-by: Ken Wilson <ken.wilson@opengear.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are more that one SPI controller on the Intel MID boards. This patch
describes the status and IDs of them. From now on we also have to care about
bus number that must be unique per host.
According to the specification the SPI1 has 5 bits for chip selects and SPI2
only 2 bits. The patch makes it depend to PCI ID.
The first controller (SPI1) is DMA capable, meanwhile SPI2 can share same
channels (via software switch) such functionality is not in the scope of this
patch. Thus, attempt to init DMA for SPI2 will always fail for now.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When autodetection is used it would be useful to know what the FIFO size is.
The patch adds a debug message for this purpose.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of warning message in ->probe() we have to use HW device name instead
of master because last is not defined yet.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There's no need to use the synchronous version.
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Support for keyword 'boolean' will be dropped later on.
No functional change.
Reference: http://lkml.kernel.org/r/cover.1418003065.git.cj@linux.com
Signed-off-by: Christoph Jaeger <cj@linux.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
"sirf,marco-spi" is redundant as all SPI controllers in CSR SiRFSoC are
compatible with prima2-spi.
at the same time, the whole marco project was dropped and its replacement
atlas7 is also compatible with prima2 in SPI.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes the following kbuild test robot warnings:
>> drivers/spi/spi-dln2.c:124:1-4: WARNING: end returns can be simplified if negative or 0 value
>> drivers/spi/spi-dln2.c:656:1-4: WARNING: end returns can be simplified if negative or 0 value
Additionally, fix a comment after switching from CONFIG_PM_RUNTIME to
CONFIG_PM.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the FLD bit field is bit[3:2], the MDR1_FLD_MASK value should
be 0x0000000c.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
The FIFO size is 40 accordingly to the specifications, but this means 0x40,
i.e. 64 bytes. This patch fixes the typo and enables FIFO size autodetection
for Intel MID devices.
Fixes: 7063c0d942 (spi/dw_spi: add DMA support)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current code tries to find the highest valid fifo depth by checking the value
it wrote to DW_SPI_TXFLTR. There are a few problems in current code:
1) There is an off-by-one in dws->fifo_len setting because it assumes the latest
register write fails so the latest valid value should be fifo - 1.
2) We know the depth could be from 2 to 256 from HW spec, so it is not necessary
to test fifo == 257. In the case fifo is 257, it means the latest valid
setting is fifo = 256. So after the for loop iteration, we should check
fifo == 2 case instead of fifo == 257 if detecting the FIFO depth fails.
This patch fixes above issues.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-and-tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The irq number is only used inside the probe function, so there is really no
need to store it in the private structure.
Use a local 'irq' variable to hold the the irq number instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Device support SPI_CPOL, but driver have missed to add
support for this configuration.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Once the current message is finished, the driver notifies SPI core about
this by calling spi_finalize_current_message(). This function queues next
message to be transferred. If there are more messages in the queue, it is
possible that the driver is asked to transfer the next message at this
point.
When spi_finalize_current_message() returns the driver clears the
drv_data->cur_chip pointer to NULL. The problem is that if the driver
already started the next message clearing drv_data->cur_chip will cause
NULL pointer dereference which crashes the kernel like:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000048
IP: [<ffffffffa0022bc8>] cs_deassert+0x18/0x70 [spi_pxa2xx_platform]
PGD 78bb8067 PUD 37712067 PMD 0
Oops: 0000 [#1] SMP
Modules linked in:
CPU: 1 PID: 11 Comm: ksoftirqd/1 Tainted: G O 3.18.0-rc4-mjo #5
Hardware name: Intel Corp. VALLEYVIEW B3 PLATFORM/NOTEBOOK, BIOS MNW2CRB1.X64.0071.R30.1408131301 08/13/2014
task: ffff880077f9f290 ti: ffff88007a820000 task.ti: ffff88007a820000
RIP: 0010:[<ffffffffa0022bc8>] [<ffffffffa0022bc8>] cs_deassert+0x18/0x70 [spi_pxa2xx_platform]
RSP: 0018:ffff88007a823d08 EFLAGS: 00010202
RAX: 0000000000000008 RBX: ffff8800379a4430 RCX: 0000000000000026
RDX: 0000000000000000 RSI: 0000000000000246 RDI: ffff8800379a4430
RBP: ffff88007a823d18 R08: 00000000ffffffff R09: 000000007a9bc65a
R10: 000000000000028f R11: 0000000000000005 R12: ffff880070123e98
R13: ffff880070123de8 R14: 0000000000000100 R15: ffffc90004888000
FS: 0000000000000000(0000) GS:ffff880079a80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000048 CR3: 000000007029b000 CR4: 00000000001007e0
Stack:
ffff88007a823d58 ffff8800379a4430 ffff88007a823d48 ffffffffa0022c89
0000000000000000 ffff8800379a4430 0000000000000000 0000000000000006
ffff88007a823da8 ffffffffa0023be0 ffff88007a823dd8 ffffffff81076204
Call Trace:
[<ffffffffa0022c89>] giveback+0x69/0xa0 [spi_pxa2xx_platform]
[<ffffffffa0023be0>] pump_transfers+0x710/0x740 [spi_pxa2xx_platform]
[<ffffffff81076204>] ? pick_next_task_fair+0x744/0x830
[<ffffffff81049679>] tasklet_action+0xa9/0xe0
[<ffffffff81049a0e>] __do_softirq+0xee/0x280
[<ffffffff81049bc0>] run_ksoftirqd+0x20/0x40
[<ffffffff810646df>] smpboot_thread_fn+0xff/0x1b0
[<ffffffff810645e0>] ? SyS_setgroups+0x150/0x150
[<ffffffff81060f9d>] kthread+0xcd/0xf0
[<ffffffff81060ed0>] ? kthread_create_on_node+0x180/0x180
[<ffffffff8187a82c>] ret_from_fork+0x7c/0xb0
Fix this by clearing drv_data->cur_chip before we call spi_finalize_current_message().
Reported-by: Martin Oldfield <m@mjoldfield.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The MSIOF controller has DTDL and SYNCDL in SITMDR1 register. So,
this patch adds new properties like the following commit:
d0fb47a523
(spi: fsl-espi: Configure FSL eSPI CSBEF and CSAFT)
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the 32-bit FIFO is deeper (64 bytes) than the 8-bit FIFO (16 bytes),
use the 32-bit FIFO when there are at least 32 bits remaining to be
transferred in PIO mode or when the transfer length is 32-bit aligned
in DMA mode.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
A 1-byte burst size is rather inefficient and has been shown to cause
TX issues during testing. Increase the DMA burst size to 4-bytes for
both RX and TX DMA when using the 8-bit FIFO.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The double call to init_completion(&mpc8xxx_spi->done); is not needed
presumably this is a editing mistake only.
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently SSP registers are accessed by having an own read and write macros
for each register. For instance read_SSSR(iobase) and write_SSSR(iobase).
In my opinion this hurts readability and requires new macros to be defined
for each new added register. Let's define and use instead common
pxa2xx_spi_read() and pxa2xx_spi_write() accessors.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pass pointer to struct driver_data instead of ioaddr to wait_ssp_rx_stall()
for preparing to register access macro cleanup.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move is_lpss_ssp() tests from functions to caller. Although this aims to
improve readability it also saves a few code bytes on x86.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds support for Diolan DLN2 USB-SPI adapter.
Information about the USB protocol interface can be found in the
Programmer's Reference Manual [1], see section 5.4.6 for the SPI
master module commands and responses.
[1] https://www.diolan.com/downloads/dln-api-manual.pdf
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for the SPI portion of ST's SSC device.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is recommended that the SPFI controller be enabled (i.e. setting
SPFI_EN in SPFI_CONTROL) before TX DMA begins.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
A couple of new CONFIG_PM_RUNTIME users have been added recently
in the SPI subsystem.
However, after commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if
PM_SLEEP is selected) PM_RUNTIME is always set if PM is set, so
#ifdef blocks depending on CONFIG_PM_RUNTIME may now be changed to
depend on CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under
drivers/spi/ (again).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by
the driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken
into account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should
have used from the start and drop some other unuseful KERN_ERR
messages printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool
(Prarit Bhargava).
- Fix two regressions introduced by recent commits in the OPP
library and clean up some existing minor issues in that code
(Viresh Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout
the tree (or drop it where that can be done) in order to make
it possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki,
Ulf Hansson, Ludovic Desroches). There will be one more
"CONFIG_PM_RUNTIME removal" batch after this one, because some
new uses of it have been introduced during the current merge
window, but that should be sufficient to finally get rid of it.
- Make the ACPI EC driver more robust against race conditions
related to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to
disable GPEs that it has not enabled which confuses ACPICA
and makes it report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver
to make it possible to override the blacklisting of some
systems in that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS
entry for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces
witn names that reflect the IDs of the ACPI device objects
they are associated with, except for "generic" ACPI fans
(PNP ID "PNP0C0B"). That's necessary for user space thermal
management tools to be able to connect the fans with the
parts of the system they are supposed to be cooling properly.
From Srinivas Pandruvada.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5fo2
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are regression fixes (leds-gpio, ACPI backlight driver,
operating performance points library, ACPI device enumeration
messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
PM), some cleanups in the operating performance points (OPP)
framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
minor intel_pstate driver changes, a new MAINTAINERS entry for it and
an ACPI fan driver change needed for better support of thermal
management in user space.
Specifics:
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by the
driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken into
account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should have
used from the start and drop some other unuseful KERN_ERR messages
printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool (Prarit
Bhargava).
- Fix two regressions introduced by recent commits in the OPP library
and clean up some existing minor issues in that code (Viresh
Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
tree (or drop it where that can be done) in order to make it
possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
Hansson, Ludovic Desroches).
There will be one more "CONFIG_PM_RUNTIME removal" batch after this
one, because some new uses of it have been introduced during the
current merge window, but that should be sufficient to finally get
rid of it.
- Make the ACPI EC driver more robust against race conditions related
to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to disable
GPEs that it has not enabled which confuses ACPICA and makes it
report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver to
make it possible to override the blacklisting of some systems in
that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS entry
for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces witn
names that reflect the IDs of the ACPI device objects they are
associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").
That's necessary for user space thermal management tools to be able
to connect the fans with the parts of the system they are supposed
to be cooling properly. From Srinivas Pandruvada"
* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
MAINTAINERS: add entry for intel_pstate
ACPI / video: update the skip case for acpi_video_device_in_dod()
power / PM: Eliminate CONFIG_PM_RUNTIME
NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / EC: Fix unexpected ec_remove_handlers() invocations
Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
ACPI / utils: Drop error messages from acpi_evaluate_reference()
...
SH-MSIOF driver is enabled autosuspend API of spi framework.
But autosuspend framework doesn't work during initializing.
So runtime PM lock is added in SH-MSIOF driver initializing.
Fixes: e2a0ba547b (spi: sh-msiof: Convert to spi core auto_runtime_pm framework)
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under
drivers/spi/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Lots of activity in the devicetree code for v3.18. Most of it is related
to getting all of the overlay support code in place, but there are other
important things in there.
There are a few trivial merge conflicts. They shouldn't give you any
trouble.
Highlights:
- OF_RECONFIG notifiers for SPI, I2C and Platform devices. Those
subsystems can now respond to live changes to the device tree.
- CONFIG_OF_OVERLAY method for applying live changes to the device tree
- Removal of the of_allnodes list. This used to be used to iterate over
all the nodes in the device tree, but it is unnecessary because the
same thing can be done by iterating over the list of child pointers.
Getting rid of of_allnodes saves some memory and avoids the
possibility of of_allnodes being sorted differently from the child
lists.
- Support for retrieving original DTB blob via sysfs. Needed by kexec.
- More unittests
- Documentation and minor bug fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ak0A
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux
Pull devicetree changes from Grant Likely:
"Lots of activity in the devicetree code for v3.18. Most of it is
related to getting all of the overlay support code in place, but there
are other important things in there.
Highlights:
- OF_RECONFIG notifiers for SPI, I2C and Platform devices. Those
subsystems can now respond to live changes to the device tree.
- CONFIG_OF_OVERLAY method for applying live changes to the device
tree
- Removal of the of_allnodes list. This used to be used to iterate
over all the nodes in the device tree, but it is unnecessary
because the same thing can be done by iterating over the list of
child pointers. Getting rid of of_allnodes saves some memory and
avoids the possibility of of_allnodes being sorted differently from
the child lists.
- Support for retrieving original DTB blob via sysfs. Needed by
kexec.
- More unittests
- Documentation and minor bug fixes"
* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux: (42 commits)
of: Delete unnecessary check before calling "of_node_put()"
of: Drop ->next pointer from struct device_node
spi: Check for spi_of_notifier when CONFIG_OF_DYNAMIC=y
of: support passing console options with stdout-path
of: add optional options parameter to of_find_node_by_path()
of: Add bindings for chosen node, stdout-path
of: Remove unneeded and incorrect MODULE_DEVICE_TABLE
ARM: dt: fix up PL011 device tree bindings
of: base, fix of_property_read_string_helper kernel-doc
of: remove select of non-existant OF_DEVICE config symbol
spi/of: Add OF notifier handler
spi/of: Create new device registration method and accessors
i2c/of: Add OF_RECONFIG notifier handler
i2c/of: Factor out Devicetree registration code
of/overlay: Add overlay unittests
of/overlay: Introduce DT overlay support
of/reconfig: Add OF_DYNAMIC notifier for platform_bus_type
of/reconfig: Always use the same structure for notifiers
of/reconfig: Add debug output for OF_RECONFIG notifiers
of/reconfig: Add empty stubs for the of_reconfig methods
...
Not a huge amount going on this release, mainly new drivers (there's a
couple more waiting that didn't quite make the cut for this release
too):
- An interface for querying if the current transfer is the last in a
message, allowing controllers that need special handling for the
final transfer to use the core message parsing.
- Support for Amlogic Meson SPIFC, Imagination Technologies SFPI, Intel
Quark X1000 and Samsung Exynos 7 controllers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUh0aVAAoJECTWi3JdVIfQ/eMH/06iz3nPi0/bkv/1bW72QbUf
glk/dT/AAPzoXPdwtxqbiHGdvt0QrarXs0nsQgqmvIA0SQRuTNvncon8UmJ9+N2B
OaCfUByC9C8hYpyc4KB4HxzN/sFx9W+F81JRLCk5+zAmn43Gofas9v2AfAy4iksD
BdIpGbcfn/0gmXqObjqfiWh2W8Sqv13goI4bHCAg5v6m58Zht9IV9vn4TSWAWB34
lq4Htn0QxMBRmzj/9iWqAzdfhZGMP1bABqpJrrGzJAws+TzFqytVXPC4iYID6RVW
u4TvOSKq9fkHkbmgapuhR2E7H4P/kYcwtEIJdT/fcUxeDF4w4s0lYNweh6tdk3I=
=wBDI
-----END PGP SIGNATURE-----
Merge tag 'spi-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Not a huge amount going on this release, mainly new drivers (there's a
couple more waiting that didn't quite make the cut for this release
too):
- An interface for querying if the current transfer is the last in a
message, allowing controllers that need special handling for the
final transfer to use the core message parsing.
- Support for Amlogic Meson SPIFC, Imagination Technologies SFPI,
Intel Quark X1000 and Samsung Exynos 7 controllers"
* tag 'spi-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (38 commits)
spi/s3c64xx: Remove redundant runtime PM management
spi: fsl-spi: remove unused variable assignment
spi: spi-fsl-spi: Return an error code in fsl_spi_do_one_msg()
spi: core: Do not mangle error code from kthread_run()
spi: fsl-espi: add (un)prepare_transfer_hardware calls to save power if SPI is not in use
spi: fsl-(e)spi: migrate to generic master queueing
spi/txx9: Deletion of an unnecessary check before the function call "clk_disable"
spi: cadence: Fix 3-to-8 mux mode
spi: cadence: Init HW after reading devicetree attributes
spi: meson: Select REGMAP_MMIO
spi: s3c64xx: add support for exynos7 SPI controller
spi: spi-pxa2xx: SPI support for Intel Quark X1000
spi: meson: meson_spifc_setup_speed() can be static
spi: spi-pxa2xx: Add helpers for regiseters' accessing
spi: spi-mxs: Fix mapping from vmalloc-ed buffer to scatter list
spi: atmel: introduce probe deferring
spi: atmel: remove compat for non DT board when requesting dma chan
spi: meson: Add support for Amlogic Meson SPIFC
spi: meson: Add device tree bindings documentation for SPIFC
spi: core: Add spi_transfer_is_last() helper
...
In order to avoid the situation where the kthread is waiting for another
context to make the hardware idle let the message pump know if it's being
called from the worker thread context and if it isn't then defer to the
worker thread instead of idling the hardware immediately. This will ensure
that if this situation happens we block rather than busy waiting.
Signed-off-by: Mark Brown <broonie@kernel.org>
If we are using the standard SPI message pump (which all drivers should be
transitioning over to) then special case the message enqueue and instead of
starting the worker thread to push messages to the hardware do so in the
context of the caller if the controller is idle. This avoids a context
switch in the common case where the controller has a single user in a
single thread, for short PIO transfers there may be no need to context
switch away from the calling context to complete the transfer.
The code is a bit more complex than is desirable in part due to the need
to handle drivers not using the standard queue and in part due to handling
the various combinations of bus locking and asynchronous submission in
interrupt context.
It is still suboptimal since it will still wake the message pump for each
transfer in order to schedule idling of the hardware and if multiple
contexts are using the controller simultaneously a caller may end up
pumping a message for some random other thread rather than for itself,
and if the thread ends up deferring due to another context idling the
hardware then it will just busy wait. It can, however, have the benefit
of aggregating power up and down of the hardware when a caller performs
a series of transfers back to back without any need for the use of
spi_async().
Signed-off-by: Mark Brown <broonie@kernel.org>
cur_msg is updated under the queue lock and holds the message we are
currently processing. Since currently we only ever do removals in the
pump kthread it doesn't matter in what order we do things but we want
to be able to push things out from the submitting thread so pull the
check to see if we're currently handling a message before we check to
see if the queue is idle.
Signed-off-by: Mark Brown <broonie@kernel.org>
Since most devices now do use the standard queue and in order to avoid
initialisation ordering issues being introduced by further refactorings
to improve performance move the initialisation of the queue and the lock
for it to the main master allocation.
Signed-off-by: Mark Brown <broonie@kernel.org>
The device already asks the core to hold a runtime PM reference while it
is active so it is redundant to open code that in the driver itself.
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit c592becbe7 ("spi: fsl-(e)spi: migrate to generic master
queueing") the function fsl_spi_do_one_msg() is not void anymore, so return
an error code to avoid the following buid warning:
drivers/spi/spi-fsl-spi.c: In function 'fsl_spi_do_one_msg':
>> drivers/spi/spi-fsl-spi.c:374:4: warning: 'return' with no value, in function returning non-void [-Wreturn-type]
return;
^
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
kthread_run() could return ERR_PTR(-EINTR) from kthread_create_on_node().
Return the actual error code in spi_init_queue() instead of mangling it to
-ENOMEM.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SET_PM_RUNTIME_PM_OPS() and SET_RUNTIME_PM_OPS() macros are
identical except that one of them is not empty for CONFIG_PM set,
while the other one is not empty for CONFIG_PM_RUNTIME set,
respectively.
However, after commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if
PM_SLEEP is selected) PM_RUNTIME is always set if PM is set, so one
of these macros is now redundant.
For this reason, replace SET_PM_RUNTIME_PM_OPS() with
SET_RUNTIME_PM_OPS() everywhere and redefine the SET_PM_RUNTIME_PM_OPS
symbol as SET_RUNTIME_PM_OPS in case new code is starting to use the
macro being removed here.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use (un)prepare_transfer_hardware calls to set fsl-espi to
low-power idle if not in use. Reference manual states:
"The eSPI is in a idle state and consumes minimal power.
The eSPI BRG is not functioning and the input clock is disabled"
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Migrates the fsl-(e)spi driver to use the generic master queuing.
Avoids the "master is unqueued, this is deprecated" warning.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The clk_disable() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
In 3-to-8 mux mode for the CS pins we need to set the PERI_SEL bit in the
control register. Currently the driver never sets this bit even when
configured for 3-to-8 mux mode. This patch adds code which sets the bit
during device initialization when necessary.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This will make it possible to use the settings specified in the devicetree
to configure the hardware.
Signed-off-by: Paul Cercueil <paul.cercueil@analog.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Meson SPIFC driver uses regmap mmio functions and so it must
select REGMAP_MMIO to avoid the following build error:
spi-meson-spifc.c: undefined reference to `devm_regmap_init_mmio_clk'
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Exynos7 SPI controller supports only the auto Selection of
CS toggle mode and Exynos7 SoC includes six SPI controllers.
Add support for these changes in Exynos7 SPI controller driver.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are two SPI controllers exported by PCI subsystem for Intel Quark X1000.
The SPI memory mapped I/O registers supported by Quark are different from
the current implementation, and Quark only supports the registers of 'SSCR0',
'SSCR1', 'SSSR', 'SSDR', and 'DDS_RATE'. This patch is to enable the SPI for
Intel Quark X1000.
This piece of work is derived from Dan O'Donovan's initial work for Intel Quark
X1000 SPI enabling.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Weike Chen <alvin.chen@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add OF notifier handler needed for creating/destroying spi devices
according to dynamic runtime changes in the DT live tree. This code is
enabled when CONFIG_OF_DYNAMIC is selected.
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Cc: <linux-spi@vger.kernel.org>
Dynamically inserting spi device nodes requires the use of a single
device registration method. Refactor the existing
of_register_spi_devices() to split out the core functionality for a
single device into a separate function; of_register_spi_device(). This
function will be used by the OF_DYNAMIC overlay code to make live
modifications to the tree.
Methods to lookup a device/master using a device node are added
as well, of_find_spi_master_by_node() & of_find_spi_device_by_node().
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
[grant.likely] Split patch into two pieces for clarity
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Cc: <linux-spi@vger.kernel.org>
drivers/spi/spi-meson-spifc.c:171:6: sparse: symbol 'meson_spifc_setup_speed' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are several registers for SPI, and the registers of 'SSCR0' and 'SSCR1'
are accessed frequently. This path is to introduce helper functions to
simplify the accessing of 'SSCR0' and 'SSCR1'.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Weike Chen <alvin.chen@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We can only use page_address on memory that has been mapped using kmap,
when the buffer passed to the SPI has been allocated by vmalloc the page
has not necessarily been mapped through kmap. This means sometimes
page_address will return NULL causing the pointer we pass to sg_init_one
to be invalid. Currently, this issue doesn't show up on the MXS
architecture as the defconfig defines CONFIG_HIGHMEM=n which means all
pages are mapped. For the sake of robustness though it is best to
correct the issue.
As we only call page_address so that we can pass a virtual address to
sg_init_one which will eventually call virt_to_page on it, fix this
by calling sg_set_page directly rather then relying on the sg_init_one
helper.
Note this patch is only build tested as I don't have an MXS system to
test on.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return probe defer if requesting a dma channel without a dma controller
probed.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All boards with a dma controller have DT support so using
dma_request_slave_channel_compat is no more needed.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a driver for the Amlogic Meson SPIFC (SPI flash controller),
which is one of the two SPI controllers available on the SoC. It
doesn't support DMA and has a 64-byte unified transmit/receive buffer.
The device is optimized for interfacing with SPI NOR memories and
allows the execution of standard operations such as read, page
program, sector erase, etc. in a simplified way, toggling a bit in a
dedicated register. The driver doesn't use those predefined commands
and relies only on custom transfers.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On CPM1, when the SPI parameter RAM is relocated to somewhere else than the
default location, in accordance with freescale documentation
(refer micropatch SPI application note EB662), init RX/TX params command shall
not be used because it doesn't take into account the new location, and
overwrites data that is in original location of SPI param ram at addresses
SCC2 param base + (u32*)0x88 (u16*)0x90 (u32*)0x98 (u16*)0xA0, hence breaking
activity on SCC2 if SCC2 is used in a mode like QMC for instance.
Therefore, the action shall be done manually as described by freescale and as
was already partly done by the driver.
Reported-by: Patrick Vasseur <patrick.vasseur@c-s.fr>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Tested-by: Patrick Vasseur <patrick.vasseur@c-s.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
in SPI boot mode, romcode uses SPI controller to fetch data from NOR
flash. Here we need to reset the hardware IP to restore its state.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
if spi device has no frequency, spi core will setup the default frequency
to max_speed_hz of spi_master according to
int spi_setup(struct spi_device *spi)
{
...
if (!spi->max_speed_hz)
spi->max_speed_hz = spi->master->max_speed_hz;
...
}
this patch moves CSR SiRFSoC SPI frequency set to follow SPI core behaviour.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 8c328a262f ("spi: sirf: Avoid duplicate code in various
bits_per_word cases") is wrong in setting data width register of
fifo is not right, it should use sspi->word_width >> 1 to set
related bits. According to hardware spec, the mapping between
register value and data width:
0 - byte
1 - WORD
2 - DWORD
Fixes: 8c328a262f ("spi: sirf: Avoid duplicate code in various bits_per_word cases") is wrong in setting data width register of
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Add support for the Synchronous Peripheral Flash Interface (SPFI) master
controller found on IMG SoCs. The SPFI controller supports 5 chip-select
lines and single/dual/quad mode SPI transfers.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We can only use page_address on memory that has been mapped using kmap,
when the buffer passed to the SPI has been allocated by vmalloc the page
has not necessarily been mapped through kmap. This means sometimes
page_address will return NULL causing the pointer we pass to sg_set_buf
to be invalid.
As we only call page_address so that we can pass a virtual address to
sg_set_buf which will then immediately call virt_to_page on it, fix this
by calling sg_set_page directly rather then relying on the sg_set_buf
helper.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The call to spi_master_put() in rockchip_spi_remove() is redundant since
the master is registered using devm_. This patch removes it.
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently spidev allows callers to set the default speed by overriding the
max_speed_hz in the underlying device. This achieves the immediate goal but
is not what devices expect and can easily lead to userspace trying to set
unsupported speeds and succeeding, apart from anything else drivers can't
set a limit on the speed using max_speed_hz as they'd expect and any other
devices on the bus will be affected.
Instead store the default speed in the spidev struct and fill this in on
each transfer.
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of registering the irq name with the driver name, it's better to pass
the device name so that we have a more explicit indication as to what spi
instance the irq is related:
$ cat /proc/interrupts
CPU0
...
27: 0 - 98 80014000.ssp
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The assignment of SPI_GPIO_NO_CHIPSELECT to cs_gpios[0] causes the following
compiler warning, when building for 64 bit systems:
"warning: overflow in implicit constant conversion [-Woverflow]".
This is because the SPI_GPIO_NO_CHIPSELECT flag is a '-1' type casted to
unsigned long and cs_gpios is of the type int.
Furthermore the chip select's GPIO number is locally stored as unsigned int
and compared with SPI_GPIO_NO_CHIPSELECT. Thus the result of the comparison
is always false, if unsigned long and unsigned int have a different size.
As part of the fix this patch adds a check for the device tree's cs-gpios
property.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Torsten Fleischer <torfl6749@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
An IOCTL call that calls spi_setup() and then dw_spi_setup() will
overwrite the persisted last transfer speed. On each transfer, the
SPI speed is compared to the last transfer speed to determine if the
clock divider registers need to be updated (did the speed change?).
This bug was observed with the spidev driver using spi-config to
update the max transfer speed.
This fix: Don't overwrite the persisted last transaction clock speed
when updating the SPI parameters in dw_spi_setup(). On the next
transaction, the new speed won't match the persisted last speed
and the hardware registers will be updated.
On initialization, the persisted last transaction clock
speed will be 0 but will be updated after the first SPI
transaction.
Move zeroed clock divider check into clock change test because
chip->clk_div is zero on startup and would cause a divide-by-zero
error. The calculation was wrong as well (can't support odd #).
Reported-by: Vlastimil Setka <setka@vsis.cz>
Signed-off-by: Vlastimil Setka <setka@vsis.cz>
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
If PM_RUNTIME is enabled, it is easy to trigger the following backtrace
on pxa2xx hosts:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at /home/lumag/linux/arch/arm/mach-pxa/clock.c:35 clk_disable+0xa0/0xa8()
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 3.17.0-00007-g1b3d2ee-dirty #104
[<c000de68>] (unwind_backtrace) from [<c000c078>] (show_stack+0x10/0x14)
[<c000c078>] (show_stack) from [<c001d75c>] (warn_slowpath_common+0x6c/0x8c)
[<c001d75c>] (warn_slowpath_common) from [<c001d818>] (warn_slowpath_null+0x1c/0x24)
[<c001d818>] (warn_slowpath_null) from [<c0015e80>] (clk_disable+0xa0/0xa8)
[<c0015e80>] (clk_disable) from [<c02507f8>] (pxa2xx_spi_suspend+0x2c/0x34)
[<c02507f8>] (pxa2xx_spi_suspend) from [<c0200360>] (platform_pm_suspend+0x2c/0x54)
[<c0200360>] (platform_pm_suspend) from [<c0207fec>] (dpm_run_callback.isra.14+0x2c/0x74)
[<c0207fec>] (dpm_run_callback.isra.14) from [<c0209254>] (__device_suspend+0x120/0x2f8)
[<c0209254>] (__device_suspend) from [<c0209a94>] (dpm_suspend+0x50/0x208)
[<c0209a94>] (dpm_suspend) from [<c00455ac>] (suspend_devices_and_enter+0x8c/0x3a0)
[<c00455ac>] (suspend_devices_and_enter) from [<c0045ad4>] (pm_suspend+0x214/0x2a8)
[<c0045ad4>] (pm_suspend) from [<c04b5c34>] (test_suspend+0x14c/0x1dc)
[<c04b5c34>] (test_suspend) from [<c000880c>] (do_one_initcall+0x8c/0x1fc)
[<c000880c>] (do_one_initcall) from [<c04aecfc>] (kernel_init_freeable+0xf4/0x1b4)
[<c04aecfc>] (kernel_init_freeable) from [<c0378078>] (kernel_init+0x8/0xec)
[<c0378078>] (kernel_init) from [<c0009590>] (ret_from_fork+0x14/0x24)
---[ end trace 46524156d8faa4f6 ]---
This happens because suspend function tries to disable a clock that is
already disabled by runtime_suspend callback. Add if
(!pm_runtime_suspended()) checks to suspend/resume path.
Fixes: 7d94a50585 (spi/pxa2xx: add support for runtime PM)
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Reported-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
In order to describe a single slave device that has no chip select line
the 'num-chipselects' property has to be <0> and the 'cs-gpios' property
doesn't need to be set.
Signed-off-by: Torsten Fleischer <torfl6749@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are only 4 CTAR registers (CTAR0 - CTAR3) so we can only use the
lower 2 bits of the chip select to select a CTAR register.
SPI_PUSHR_CTAS used the lower 3 bits which would result in wrong bit values
if the chip selects 4/5 are used. For those chip selects SPI_CTAR even
calculated offsets of non-existing registers.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Currently driver wouldn't work properly if user asked for simplex transfer. The
patch separates DMA rx and tx callbacks and finishes transfer correctly in any
case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch splits few helpers, namely dw_spi_dma_prepare_rx(),
dw_spi_dma_prepare_tx(), and dw_spi_dma_setup() which will be useful for the
consequent improvements.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It's possible that the call to of_match_device() (introduced in commit
df59fa7f ["spi: orion: support armada extended baud rates"]) may return
a NULL if there is no match in the device tree (or perhaps no device tree
at all). Check the return pointer and set the local device data to the
lowest common denominator orion device data if it is NULL.
Reported-by: Karl Beldan <karl.beldan@gmail.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
To make it cleaner, the system suspend/resume directly call
the runtime suspend/resume functions
and remove the wapper of CONFIG_PM_RUNTIME, CONFIG_PM_SLEEP.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since we are using regmap framework's internal locks, so the
lock_arg for dspi_regmap_config is redundant here.
This patch just remove it, and then the dspi_regmap_config could
be const type.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
drivers/spi/spi-atmel.c:1518:1-4: WARNING: end returns can be simpified and declaration on line 1514 can be dropped
Simplify a trivial if-return sequence. Possibly combine with a
preceding function call.
Generated by: scripts/coccinelle/misc/simple_return.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Drivers should put the device into low power states proactively whenever the
device is not in use. Thus implement support for runtime PM and use the
autosuspend feature to make sure that we can still perform well in case we see
lots of SPI traffic within short period of time.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The drivers should use dmaengine_terminate_all() API instead of
accessing the device_control which will be deprecated soon
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull slave-dmaengine updates from Vinod Koul:
"For dmaengine contributions we have:
- designware cleanup by Andy
- my series moving device_control users to dmanegine_xxx APIs for
later removal of device_control API
- minor fixes spread over drivers mainly mv_xor, pl330, mmp, imx-sdma
etc"
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (60 commits)
serial: atmel: add missing dmaengine header
dmaengine: remove FSLDMA_EXTERNAL_START
dmaengine: freescale: remove FSLDMA_EXTERNAL_START control method
carma-fpga: move to fsl_dma_external_start()
carma-fpga: use dmaengine_xxx() API
dmaengine: freescale: add and export fsl_dma_external_start()
dmaengine: add dmaengine_prep_dma_sg() helper
video: mx3fb: use dmaengine_terminate_all() API
serial: sh-sci: use dmaengine_terminate_all() API
net: ks8842: use dmaengine_terminate_all() API
mtd: sh_flctl: use dmaengine_terminate_all() API
mtd: fsmc_nand: use dmaengine_terminate_all() API
V4L2: mx3_camer: use dmaengine_pause() API
dmaengine: coh901318: use dmaengine_terminate_all() API
pata_arasan_cf: use dmaengine_terminate_all() API
dmaengine: edma: check for echan->edesc => NULL in edma_dma_pause()
dmaengine: dw: export probe()/remove() and Co to users
dmaengine: dw: enable and disable controller when needed
dmaengine: dw: always export dw_dma_{en,dis}able
dmaengine: dw: introduce dw_dma_on() helper
...
In rx mode, dma must be prepared before spi is enabled.
But in tx and tr mode, spi must be enabled first.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Because the minimum divisor in rk3x's spi controller is 2,
if spi_clk is less than 2 * sclk_out, we can't get the right divisor.
So we must set spi_clk again to match slave request.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When mapped RX DMA entries are unmapped in an error condition when DMA
is firstly configured in the driver, the number of TX DMA entries was
passed in, which is incorrect
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
By using separate TX and RX bounce buffers, we avoid potential cache
flush and invalidation sequence issue that may be encountered when a
single bounce buffer is shared between TX and RX
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: JD (Jiandong) Zheng <jdzheng@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Rework the handling of wakeup IRQs by the IRQ core such that
all of them will be switched over to "wakeup" mode in
suspend_device_irqs() and in that mode the first interrupt
will abort system suspend in progress or wake up the system
if already in suspend-to-idle (or equivalent) without executing
any interrupt handlers. Among other things that eliminates the
wakeup-related motivation to use the IRQF_NO_SUSPEND interrupt
flag with interrupts which don't really need it and should not
use it (Thomas Gleixner and Rafael J Wysocki).
- Switch over ACPI to handling wakeup interrupts with the help
of the new mechanism introduced by the above IRQ core rework
(Rafael J Wysocki).
- Rework the core generic PM domains code to eliminate code that's
not used, add DT support and add a generic mechanism by which
devices can be added to PM domains automatically during
enumeration (Ulf Hansson, Geert Uytterhoeven and Tomasz Figa).
- Add debugfs-based mechanics for debugging generic PM domains
(Maciej Matraszek).
- ACPICA update to upstream version 20140828. Included are updates
related to the SRAT and GTDT tables and the _PSx methods are in
the METHOD_NAME list now (Bob Moore and Hanjun Guo).
- Add _OSI("Darwin") support to the ACPI core (unfortunately, that
can't really be done in a straightforward way) to prevent
Thunderbolt from being turned off on Apple systems after boot
(or after resume from system suspend) and rework the ACPI Smart
Battery Subsystem (SBS) driver to work correctly with Apple
platforms (Matthew Garrett and Andreas Noever).
- ACPI LPSS (Low-Power Subsystem) driver update cleaning up the
code, adding support for 133MHz I2C source clock on Intel Baytrail
to it and making it avoid using UART RTS override with Auto Flow
Control (Heikki Krogerus).
- ACPI backlight updates removing the video_set_use_native_backlight
quirk which is not necessary any more, making the code check the
list of output devices returned by the _DOD method to avoid
creating acpi_video interfaces that won't work and adding a quirk
for Lenovo Ideapad Z570 (Hans de Goede, Aaron Lu and Stepan Bujnak).
- New Win8 ACPI OSI quirks for some Dell laptops (Edward Lin).
- Assorted ACPI code cleanups (Fabian Frederick, Rasmus Villemoes,
Sudip Mukherjee, Yijing Wang, and Zhang Rui).
- cpufreq core updates and cleanups (Viresh Kumar, Preeti U Murthy,
Rasmus Villemoes).
- cpufreq driver updates: cpufreq-cpu0/cpufreq-dt (driver name
change among other things), ppc-corenet, powernv (Viresh Kumar,
Preeti U Murthy, Shilpasri G Bhat, Lucas Stach).
- cpuidle support for DT-based idle states infrastructure, new
ARM64 cpuidle driver, cpuidle core cleanups (Lorenzo Pieralisi,
Rasmus Villemoes).
- ARM big.LITTLE cpuidle driver updates: support for DT-based
initialization and Exynos5800 compatible string (Lorenzo Pieralisi,
Kevin Hilman).
- Rework of the test_suspend kernel command line argument and
a new trace event for console resume (Srinivas Pandruvada,
Todd E Brandt).
- Second attempt to optimize swsusp_free() (hibernation core) to
make it avoid going through all PFNs which may be way too slow on
some systems (Joerg Roedel).
- devfreq updates (Paul Bolle, Punit Agrawal, Ãrjan Eide).
- rockchip-io Adaptive Voltage Scaling (AVS) driver and AVS
entry update in MAINTAINERS (Heiko Stübner, Kevin Hilman).
- PM core fix related to clock management (Geert Uytterhoeven).
- PM core's sysfs code cleanup (Johannes Berg).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=sIv/
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"Features-wise, to me the most important this time is a rework of
wakeup interrupts handling in the core that makes them work
consistently across all of the available sleep states, including
suspend-to-idle. Many thanks to Thomas Gleixner for his help with
this work.
Second is an update of the generic PM domains code that has been in
need of some care for quite a while. Unused code is being removed, DT
support is being added and domains are now going to be attached to
devices in bus type code in analogy with the ACPI PM domain. The
majority of work here was done by Ulf Hansson who also has been the
most active developer this time.
Apart from this we have a traditional ACPICA update, this time to
upstream version 20140828 and a few ACPI wakeup interrupts handling
patches on top of the general rework mentioned above. There also are
several cpufreq commits including renaming the cpufreq-cpu0 driver to
cpufreq-dt, as this is what implements generic DT-based cpufreq
support, and a new DT-based idle states infrastructure for cpuidle.
In addition to that, the ACPI LPSS driver is updated, ACPI support for
Apple machines is improved, a few bugs are fixed and a few cleanups
are made all over.
Finally, the Adaptive Voltage Scaling (AVS) subsystem now has a tree
maintained by Kevin Hilman that will be merged through the PM tree.
Numbers-wise, the generic PM domains update takes the lead this time
with 32 non-merge commits, second is cpufreq (15 commits) and the 3rd
place goes to the wakeup interrupts handling rework (13 commits).
Specifics:
- Rework the handling of wakeup IRQs by the IRQ core such that all of
them will be switched over to "wakeup" mode in suspend_device_irqs()
and in that mode the first interrupt will abort system suspend in
progress or wake up the system if already in suspend-to-idle (or
equivalent) without executing any interrupt handlers. Among other
things that eliminates the wakeup-related motivation to use the
IRQF_NO_SUSPEND interrupt flag with interrupts which don't really
need it and should not use it (Thomas Gleixner and Rafael Wysocki)
- Switch over ACPI to handling wakeup interrupts with the help of the
new mechanism introduced by the above IRQ core rework (Rafael Wysocki)
- Rework the core generic PM domains code to eliminate code that's
not used, add DT support and add a generic mechanism by which
devices can be added to PM domains automatically during enumeration
(Ulf Hansson, Geert Uytterhoeven and Tomasz Figa).
- Add debugfs-based mechanics for debugging generic PM domains
(Maciej Matraszek).
- ACPICA update to upstream version 20140828. Included are updates
related to the SRAT and GTDT tables and the _PSx methods are in the
METHOD_NAME list now (Bob Moore and Hanjun Guo).
- Add _OSI("Darwin") support to the ACPI core (unfortunately, that
can't really be done in a straightforward way) to prevent
Thunderbolt from being turned off on Apple systems after boot (or
after resume from system suspend) and rework the ACPI Smart Battery
Subsystem (SBS) driver to work correctly with Apple platforms
(Matthew Garrett and Andreas Noever).
- ACPI LPSS (Low-Power Subsystem) driver update cleaning up the code,
adding support for 133MHz I2C source clock on Intel Baytrail to it
and making it avoid using UART RTS override with Auto Flow Control
(Heikki Krogerus).
- ACPI backlight updates removing the video_set_use_native_backlight
quirk which is not necessary any more, making the code check the
list of output devices returned by the _DOD method to avoid
creating acpi_video interfaces that won't work and adding a quirk
for Lenovo Ideapad Z570 (Hans de Goede, Aaron Lu and Stepan Bujnak)
- New Win8 ACPI OSI quirks for some Dell laptops (Edward Lin)
- Assorted ACPI code cleanups (Fabian Frederick, Rasmus Villemoes,
Sudip Mukherjee, Yijing Wang, and Zhang Rui)
- cpufreq core updates and cleanups (Viresh Kumar, Preeti U Murthy,
Rasmus Villemoes)
- cpufreq driver updates: cpufreq-cpu0/cpufreq-dt (driver name change
among other things), ppc-corenet, powernv (Viresh Kumar, Preeti U
Murthy, Shilpasri G Bhat, Lucas Stach)
- cpuidle support for DT-based idle states infrastructure, new ARM64
cpuidle driver, cpuidle core cleanups (Lorenzo Pieralisi, Rasmus
Villemoes)
- ARM big.LITTLE cpuidle driver updates: support for DT-based
initialization and Exynos5800 compatible string (Lorenzo Pieralisi,
Kevin Hilman)
- Rework of the test_suspend kernel command line argument and a new
trace event for console resume (Srinivas Pandruvada, Todd E Brandt)
- Second attempt to optimize swsusp_free() (hibernation core) to make
it avoid going through all PFNs which may be way too slow on some
systems (Joerg Roedel)
- devfreq updates (Paul Bolle, Punit Agrawal, Ãrjan Eide).
- rockchip-io Adaptive Voltage Scaling (AVS) driver and AVS entry
update in MAINTAINERS (Heiko Stübner, Kevin Hilman)
- PM core fix related to clock management (Geert Uytterhoeven)
- PM core's sysfs code cleanup (Johannes Berg)"
* tag 'pm+acpi-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (105 commits)
ACPI / fan: printk replacement
PM / clk: Fix crash in clocks management code if !CONFIG_PM_RUNTIME
PM / Domains: Rename cpu_data to cpuidle_data
cpufreq: cpufreq-dt: fix potential double put of cpu OF node
cpufreq: cpu0: rename driver and internals to 'cpufreq_dt'
PM / hibernate: Iterate over set bits instead of PFNs in swsusp_free()
cpufreq: ppc-corenet: remove duplicate update of cpu_data
ACPI / sleep: Rework the handling of ACPI GPE wakeup from suspend-to-idle
PM / sleep: Rename platform suspend/resume functions in suspend.c
PM / sleep: Export dpm_suspend_late/noirq() and dpm_resume_early/noirq()
ACPICA: Introduce acpi_enable_all_wakeup_gpes()
ACPICA: Clear all non-wakeup GPEs in acpi_hw_enable_wakeup_gpe_block()
ACPI / video: check _DOD list when creating backlight devices
PM / Domains: Move dev_pm_domain_attach|detach() to pm_domain.h
cpufreq: Replace strnicmp with strncasecmp
cpufreq: powernv: Set the cpus to nominal frequency during reboot/kexec
cpufreq: powernv: Set the pstate of the last hotplugged out cpu in policy->cpus to minimum
cpufreq: Allow stop CPU callback to be used by all cpufreq drivers
PM / devfreq: exynos: Enable building exynos PPMU as module
PM / devfreq: Export helper functions for drivers
...
The of_node element must be initialized to enable discovery of node
children which takes place in the of_register_spi_devices() function.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Though intel-mid-dma does not follow a new DMA workflow (*) let's prepare SPI
DW driver for that.
(*) The client is obliged to call dma_async_issue_pending() which starts the
actual transfers. Old DMA drivers do not follow this, since requirement was
introduced in the discussion of [1].
[1] http://www.spinics.net/lists/arm-kernel/msg125987.html
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of direct dereference to dmaengine callbacks we are going to use
DMAengine wrappers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of using magic numbers in the code we create a bit map definition of
the DMACR register and use it.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Armada SoC family implementation of this SPI hardware module has
extended the configuration register to allow for a wider range of SPI
clock rates. Specifically the Serial Baud Rate Pre-selection bits in the
SPI Interface Configuration Register now also use bits 6 and 7 as well.
Modify the baud rate calculation to handle these differences for the
Armada case. Potentially a baud rate can be setup using a number of
different pre-scalar and scalar combinations. This code tries all
possible pre-scalar divisors (8 in total) to try and find the most
accurate set.
This change introduces (and documents) a new device tree compatible
device name "armada-370-spi" to support this.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The commit 46420dd73b (PM / Domains: Add APIs to attach/detach a PM
domain for a device) started using errno values in pm.h header file.
It also failed to include the header for these, thus it caused
compiler errors.
Instead of including the errno header to pm.h, let's move the functions
to pm_domain.h, since it's a better match.
Fixes: 46420dd73b (PM / Domains: Add APIs to attach/detach a PM domain for a device)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Sort all the include headers alphabetically for the freescale
spi drivers. If the inlcude headers sorted out of order, maybe
the best logical choice is to append new ones after the exist
ones, while this may create a lot of potential for duplicates
and conflicts for each diffenent changes will add new headers
in the same location.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mainly to fix missing MODULE_LICENSE.
Also add MODULE_DESCRIPTION and MODULE_AUTHOR.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
config SPI_BCM53XX needs to depend on BCMA_POSSIBLE and select BCMA.
This fixes below build error:
ERROR: "bcma_driver_unregister" [drivers/spi/spi-bcm53xx.ko] undefined!
ERROR: "__bcma_driver_register" [drivers/spi/spi-bcm53xx.ko] undefined!
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In my test on RK3288-pinky board, if spi is enabled, it will begin to
read data from slave regardless of whether the DMA is ready. So we
need prepare DMA before spi is enable.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Remove the probe info message which also has wrong output. No need to add
KERN_INFO to pr_info. Output was:
6Freescale DSPI master initialized
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for a extended PL022 which has an extra register for controlling up
to five chip select signals. This controller is found on the AXM5516 SoC.
Unfortunately the PrimeCell identification registers are identical to a
standard ARM PL022. To work around this, the peripheral ID must be overridden
in the device tree using the "arm,primecell-periphid" property with the value
0x000b6022.
Signed-off-by: Anders Berg <anders.berg@avagotech.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since we cannot make sure the 'n' will always be none zero here, and
then if either equal to zero, the kzalloc() will return ZERO_SIZE_PTR,
which equals to ((void *)16).
So this patch fix this with just doing the zero check before calling
kzalloc().
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make comments be surrounded by spaces and move part of code to one line where
it suits 80 characters.
There is no functional changes.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For testing purposes it's good to have a loopback mode enabled. The patch adds
necessary bits for that.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Do full clean up at exit, means terminate all ongoing DMA transfers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
In case of 8 bit mode and DMA usage we end up with every second byte written as
0. We have to respect bits_per_word settings what this patch actually does.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Currently clps711x arch have a fully functional CLK driver.
This patch migrates clps711x-spi driver to use the new CLK subsystem.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
Previously only the ACPI PM domain was supported by the spi bus.
Let's convert to the common attach/detach functions for PM domains,
which currently means we are extending the support to include the
generic PM domain as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently this driver is missing a check on the return value of devm_kzalloc,
which would cause a NULL pointer dereference in a OOM situation.
This patch adds a missing check.
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of one port we have 3 ports and all of them can take advantage of
the shared DMA controller.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
That field has been deprecated in favour of getting the necessary
information from ACPI/DT.
However, we still need to deal systems that are PCI only (no ACPI to back
up). In order to support such systems, we allow the DMA filter function and
its corresponding parameter via pxa2xx_spi_master platform data. Then when
the pxa2xx_spi_dma_setup() doesn't find the channel via ACPI, it falls back
to use the given filter function.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Enable DMA support on i.mx6. The read speed can increase from 600KB/s
to 1.2MB/s on i.mx6q. You can disable or enable dma function in dts.
If not set "dma-names" in dts, spi will use PIO mode. This patch only
validate on i.mx6, not i.mx5, but encourage ones to apply this patch
on i.mx5 since they share the same IP.
Note:
Sometime, there is a weid data in rxfifo after one full tx/rx
transfer finish by DMA on i.mx6dl, so we disable dma functhion on
i.mx6dl.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Robin Gong <b38343@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds ability to configure delay between transmission of
words over SPI bus if it's required by SPI slave devices.
New optional SPI slave property:
- ti,spi-word-delay : delay between transmission of words
(SPIFMTn.WDELAY, SPIDAT1.WDEL)
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove empty function davinci_spi_cleanup().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now CS GPIOs are requested from struct spi_master.setup() callback
and that causes failures when Client SPI device is getting accessed
through SPIDEV driver. The failure happens, because .setup() callback
may be called many times from IOCTL handler and when it's called
second time gpio_request() will fail and return -EBUSY.
Hence, fix it by moving CS GPIOs requesting code in .probe().
Reported-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since driver is used on other platforms and debugfs stuff would be useful there
as well let's substitute mrst_ by dw_ where it suits. Additionally let's use
SPI master device name when print registers dump.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The FSF address is subject to change, thus remove it from the file. While here,
update a copyright line.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of using that member we prefer to use dma_dev which represents actual
struct device of the DMA device.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Gregory CLEMENT
Michael Welling
Jane Wan
Haikun Wang
Qipan Li
kbuild test robot
Martin Sperl
Mark Brown
Fabio Estevam
Hiep Cao Minh
Geert Uytterhoeven
Yoshinori Sato
Krzysztof Kozlowski
Axel Lin
Alban Bedel
Jonatas Rech
Linus Torvalds
Christophe Leroy
Fionn Cleary
Bert Vermeulen
Pelle Nilsson
Robin Gong
Guenter Roeck
Ezequiel Garcia
Andrew Bresticker
Sifan Naeem
Geert Uytterhoeven
Aaron Brice
Dan Carpenter
Lucas Stach
Chen Gang
Michael Grzeschik
Julius Werner
Dmitry Torokhov
Andy Shevchenko
Ian Abbott
Jarkko Nikula
Ben Dooks
Uwe Kleine-König
Thor Thayer
Fabian Frederick
Ivan T. Ivanov
Michal Simek
Lars-Peter Clausen
Andy Gross
Alexander Sverdlin
Stefan Agner
Torsten Fleischer
Andre Przywara
Arnd Bergmann
Mugunthan V N
Joe Perches
Nicholas Mc Guire
Nicholas Mc Guire
Rob Herring
Bhuvanchandra DV
Nobuhiro Iwamatsu
Ricardo Ribalda Delgado
Chao Fu
Ken Wilson
Christoph Jaeger
Barry Song
Esben Haabendal
Laurentiu Palcu
Yoshihiro Shimoda
Krzysztof Kozlowski
Nizam Haider
Mika Westerberg
Lee Jones
Rafael J. Wysocki
Hisashi Nakamura
Heiner Kallweit
Markus Elfring
Paul Cercueil
Beniamino Galvani
Padmavathi Venna
Weike Chen
Pantelis Antoniou
Charles Keepax
Ludovic Desroches
Dmitry Eremin-Solenikov
Alexander Stein
Greg Kroah-Hartman
Greg Ungerer
Wenyou Yang
Wolfram Sang
Xiubo Li
Vinod Koul
Addy Ke
Ray Jui
Michael Heimpold
Ulf Hansson
Anders Berg
Alexander Shiyan
Kiran Padwal
Murali Karicheri
Grygorii Strashko