Split up the pins for each fan. This is needed in order to control them
Fixes: ced8025b56 ("ARM: dts: armada388-helios4")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Newer Linksys boards might come with a Winbond W29N02GV which can be
configured in different ways. Make sure we configure it the same way
as the older chips so everything keeps working.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
usbphyc is a 48Mhz clock provider: the clock can be used as clock source
for USB OTG. Add #clock-cells property to usbphyc node to reflect this
capability.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
vdda1v1 and vdda1v8 supplies are required by USB PLL, not by the PHYs.
Remove them from usbphyc child phy nodes now that they are managed in
usbphyc parent node at SoC level.
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
vdda1v1 and vdda1v8 supplies are required by USB PLL. Add them in usbphyc
node.
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add SDA/SCL pinmux lines for I2C6 on STM32MP1.
This support adds both in default and sleep states.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Increase the SmartEEE Tw parameter for Atheros PHYs to stop gigabit
links from sporadically dropping. Jon Nettleton found that a value
of 23 was the minimum to give a stable link, but testing with the
Com Express 7 module shows 24 is the minimum - so 23 may still be on
the margins. Use 24 instead for consistency across SolidRun platforms.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The CEC and hotplug interrupts go through an interrupt controller shared
between the two HDMI controllers.
Let's add that interrupt controller and the interrupts for both HDMI
controllers
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20210111142309.193441-16-maxime@cerno.tech
The recent changes to switch SoCs to boot with ti-sysc interconnect
target module driver and genpd caused few regressions:
- The omap_prm reset driver needs to clear any reset bits deasserted by
the bootloader or kexec boot for the three reset bit cases. Otherwise
we can have an oops with accelerators starting to boot with potentially
unconfigured MMU for example
- Custom kernel configs are not automatically selecting simple-pm-bus
driver that we now need to probe interconnects so we need to select it
always
- We are not passing legacy platform data in auxdata with simple-pm-bus
like we do for simple-bus. We need to pass auxdata to simple-pm-bus so
it can pass it to of_platform_populate()
Then recent RCU changes started causing splats for cpuidle44xx that now
need RCU_NONIDLE added to the calls in several places
And then we have few device specific fixes:
- We need to remove legacy spi-cs-hig for gta04 display to work, and
set the gpio to active low
- Omap1 specific ohci-omap needs to call gpio_free()
- Droid4 needs to use padconf interrupt for the slider as the edge
gpio interrupts may be lost for deeper idle states
-----BEGIN PGP SIGNATURE-----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=KgUu
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.11/fixes-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.11-rc cycle
The recent changes to switch SoCs to boot with ti-sysc interconnect
target module driver and genpd caused few regressions:
- The omap_prm reset driver needs to clear any reset bits deasserted by
the bootloader or kexec boot for the three reset bit cases. Otherwise
we can have an oops with accelerators starting to boot with potentially
unconfigured MMU for example
- Custom kernel configs are not automatically selecting simple-pm-bus
driver that we now need to probe interconnects so we need to select it
always
- We are not passing legacy platform data in auxdata with simple-pm-bus
like we do for simple-bus. We need to pass auxdata to simple-pm-bus so
it can pass it to of_platform_populate()
Then recent RCU changes started causing splats for cpuidle44xx that now
need RCU_NONIDLE added to the calls in several places
And then we have few device specific fixes:
- We need to remove legacy spi-cs-hig for gta04 display to work, and
set the gpio to active low
- Omap1 specific ohci-omap needs to call gpio_free()
- Droid4 needs to use padconf interrupt for the slider as the edge
gpio interrupts may be lost for deeper idle states
* tag 'omap-for-v5.11/fixes-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap4-droid4: Fix lost keypad slide interrupts for droid4
drivers: bus: simple-pm-bus: Fix compatibility with simple-bus for auxdata
ARM: OMAP2+: Fix booting for am335x after moving to simple-pm-bus
ARM: OMAP2+: Fix suspcious RCU usage splats for omap_enter_idle_coupled
ARM: dts; gta04: SPI panel chip select is active low
soc: ti: omap-prm: Fix boot time errors for rst_map_012 bits 0 and 1
ARM: OMAP1: OSK: fix ohci-omap breakage
DTS: ARM: gta04: remove legacy spi-cs-high to make display work again
Link: https://lore.kernel.org/r/pull-1611818709-243493@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit 7536c7e03e ("of/fdt: Remove redundant kbasename function
call") exposed a bug creating DT nodes in the ATAGS to DT fixup code.
Non-existent nodes would mistaken get created with a leading '/'. The
problem was fdt_path_offset() takes a full path while creating a node
with fdt_add_subnode() takes just the basename.
Since this we only add root child nodes, we can just skip over the '/'.
Fixes: 7536c7e03e ("of/fdt: Remove redundant kbasename function call")
Reported-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Qi Zheng <arch0.zheng@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Rob Herring <robh@kernel.org>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20210126023905.1631161-1-robh@kernel.org
This patch adds basic support for MYIR Tech MYC-AM335X CPU Module:
- Up to 1GHz TI AM335X Series ARM Cortex-A8 Processors
- Up to 512MB DDR3 SDRAM
- Up to 512MB Nand Flash
and MYD-AM335X Development Board:
- MYC-AM335X CPU Module as Controller Board
- Serial ports, 4 x USB Host, OTG, 2 x Gigabit Ethernet, CAN, RS485,
TF, Audio
- Supports HDMI and LCD Display
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Tony Lindgren <tony@atomide.com>
I've switched employer a long time ago and the mentioned email address no
longer exists. Use my personal address to prevent the issue in the future.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Previously, the 1GHz variants were marked as a turbo,
because that variant has reduced thermal operating range.
Now that the thermal throttling is in place, it should be
safe to remove the turbo-mode from the 1GHz variants, because
the CPU will automatically slow if the thermal limit is reached.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Android vendor kernel uses 307.2MHz or a divider ratio of /5 while active
153600000 or /10 is only used when the sgx core is inactive.
Signed-off-by: Carl Philipp Klemm <philipp@uvos.xyz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omap4430 HS HIGH performance devces support 1.2GHz opp, lower speed
variants do not. However for mapphone devices Motorola seems to have
decided that this does not really matter for the SoC variants they have
tested to use, and decided to clock all devices, including the ones with
STANDARD performance chips at 1.2GHz upon release of the 3.0.8 vendor
kernel shiped with Android 4.0. Therefore it seems safe to do the same,
but let's only do it for Motorola devices as the others have not been
tested.
Note that we prevent overheating with the passive cooling device
cpu_alert0 configured in the dts file that starts lowering the speed as
needed.
This also removes the "failed to find current OPP for freq 1200000000"
warning.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Carl Philipp Klemm <philipp@uvos.xyz>
[tony@atomide.com: made motorola specific, updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The current cooling device temperature is too high at 100C as we have a
battery on the device right next to the SoC as pointed out by Carl Philipp
Klemm <philipp@uvos.xyz>. Let's configure the max temperature to 80C.
As we only have a tshut interrupt and no talert interrupt on 4430, we have
a passive cooling device configured for 4430. However, we want the poll
interval to be 10 seconds instead of 1 second for power management. The
value of 10 seconds seems like plenty of time to notice the temperature
increase above the 75C temperatures. Having the bandgap temperature change
seems to take several tens of seconds because of heat dissipation above
75C range as monitored with a full CPU load.
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Suggested-by: Carl Philipp Klemm <philipp@uvos.xyz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We have gpio_86 wired internally to the bandgap thermal shutdown
interrupt on 4430 like we have it on 4460 according to the TRM.
This can be found easily by searching for TSHUT.
For some reason the thermal shutdown interrupt was never added
for 4430, let's add it. I believe this is needed for the thermal
shutdown interrupt handler ti_bandgap_tshut_irq_handler() to call
orderly_poweroff().
Fixes: aa9bb4bb88 ("arm: dts: add omap4430 thermal data")
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds audio playback to the first generation Amazon Echo
Signed-off-by: André Hentschel <nerv@dawncrow.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Recently introduced async probe on mmc devices can shuffle block IDs.
Pin them to fixed values to ease booting in environments where UUIDs are
not practical. Use newly introduced aliases for mmcblk devices from [1].
The sort order is based on reg address.
[1] https://patchwork.kernel.org/patch/11747669/
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210118155242.7172-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Recently introduced async probe on mmc devices can shuffle block IDs.
Pin them to fixed values to ease booting in environments where UUIDs are
not practical. Use newly introduced aliases for mmcblk devices from [1].
The sort order is based on reg address.
[1] https://patchwork.kernel.org/patch/11747669/
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210118155242.7172-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The "amba" bus nodes wrapping all the DMA-330 nodes serve no useful
purpose, and certainly bear no relation at all to the actual underlying
interconnect topology. They appear to be cargo-cult copying from a
design misstep in the very early days of FDT adoption on ARM, which was
righted with the "arm,primecell" compatible, and the last trace of the
idea finally purged by commit 2ef7d5f342 ("ARM, ARM64: dts: drop
"arm,amba-bus" in favor of "simple-bus"").
As such, they can simply be removed and the DMA-330 nodes fitted into
the normal sort order.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/e682edd25133bde2ed8198138febc90071530a51.1611186142.git.robin.murphy@arm.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Fix checkpatch warning:
WARNING: please, no spaces at the start of a line
Signed-off-by: Stanislav Jakubek <stano.jakubek@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The BSC controllers used for the HDMI DDC have an interrupt controller
shared between both instances. Let's add it to avoid polling.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20210111142309.193441-1-maxime@cerno.tech
RPi4's co-processor will copy the board's bootloader[1] configuration
into memory for the OS to consume. Specifically, for the bootloader
configuration and upgrade user-space routines to query it through
nvmem's sysfs interface.
Introduce a reserved-memory area template for the co-processor to edit
before booting the system so as for Linux not to overwrite that memory
and to expose it as an nvmem device.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Tim Gover <tim.gover@raspberrypi.com>
Link: https://lore.kernel.org/r/e8ca9365-a1f2-1f9d-377c-13bf97883cce@linaro.org
[1] https://www.raspberrypi.org/documentation/hardware/raspberrypi/bcm2711_bootloader_config.md
Updates the compatible string for DSI1 on BCM2711 to
differentiate it from BCM2835.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20201203132543.861591-9-maxime@cerno.tech
The vendor kernel uses the following thermal-zone settings:
<= 70°C:
- CPU frequency limited to 1.488GHz
- GPU limited to 511MHz and 2 cores (pixel processors)
<= 80°C:
- CPU frequency limited to 1.2GHz
- GPU limited to 435MHz and 2 cores (pixel processors)
<= 90°C:
- CPU frequency limited to 0.804GHz
- GPU limited to 328MHz and 1 core (pixel processor)
Add simplified thermal configuration which is taken from the
GXBB/GXL/GXM SoC family (which uses the same manufacturing process and
has the same maximum junction temperature of 125°C). With this the
thermal framework will try to keep the SoC temperature at or below 80°C
which is identical to the vendor kernel (with the exception of one CPU
frequency step from 1.488GHz to 1.536GHz).
The number of GPU cores are not taken into account as this is not
supported.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201221181306.904272-5-martin.blumenstingl@googlemail.com
The vendor kernel uses the following thermal-zone settings:
<= 70°C:
- CPU frequency limited to 1.608GHz
- GPU limited to 511MHz and 5 cores (pixel processors)
<= 80°C:
- CPU frequency limited to 1.2GHz
- GPU limited to 435MHz and 4 cores (pixel processors)
<= 90°C:
- CPU frequency limited to 0.804GHz
- GPU limited to 328MHz and 3 cores (pixel processors)
Add simplified thermal configuration which is taken from the
GXBB/GXL/GXM SoC family (which uses the same manufacturing process and
has the same maximum junction temperature of 125°C). With this the
thermal framework will try to keep the SoC temperature at or below 80°C
which is identical to the vendor kernel (with the exception of one GPU
pixel processor).
The number of GPU cores are not taken into account as this is not
supported.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201221181306.904272-4-martin.blumenstingl@googlemail.com
The SoC temperature can be retrieved from ADC channel 8 on all 32-bit
SoCs (Meson6, Meson8, Meson8b and Meson8m2). Add a "generic-adc-thermal"
instance to meson.dtsi so the thermal sensor is available for all SoCs.
If the temperature sensor calibration data is missing for a board then
the "generic-adc-thermal" will not probe and not register a thermal
sensor.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201221181306.904272-3-martin.blumenstingl@googlemail.com
The SoC temperature can be retrieved from ADC channel 8 on all 32-bit
SoCs (Meson6, Meson8, Meson8b and Meson8m2). Move the iio-hwmon instance
to meson.dtsi instead of duplicating it in all board.dts.
If the temperature sensor calibration data is missing for a board then
iio-hwmon will simply not probe.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201221181306.904272-2-martin.blumenstingl@googlemail.com
Since we now have driver for the SDHCI VQMMC LDO needed
for I/0 voltage levels lets introduce the necessary node for it.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Link: https://lore.kernel.org/r/20200907101937.10155-1-robert.marko@sartura.hr
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The DHCOM SoM uSD slot has an optional voltage level translator, add
DT bindings which permit the MMCI driver to detect the translator
automatically.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Ludovic Barre <ludovic.barre@st.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-stm32@st-md-mailman.stormreply.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add "init" mux option for SDMMC1, where the CMD, CK, CKIN lines are not
configured, so they can be claimed as GPIOs early on in driver probe().
This is used for probing optional voltage level translator.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Ludovic Barre <ludovic.barre@st.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-stm32@st-md-mailman.stormreply.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
We may lose edge interrupts for gpio banks other than the first gpio
bank as they are not always powered. Instead, we must use the padconf
interrupt as that is always powered.
Note that we still also use the gpio for reading the pin state as that
can't be done with the padconf device.
Signed-off-by: Tony Lindgren <tony@atomide.com>
In accordance with the DWC USB3 bindings the corresponding node
name is suppose to comply with the Generic USB HCD DT schema, which
requires the USB nodes to have the name acceptable by the regexp:
"^usb(@.*)?" . Make sure the "snps,dwc3"-compatible nodes are correctly
named.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Syonpsys IP cores are supposed to be defined with "snps" vendor-prefix.
Use it instead of the deprecated "synopsys" one.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmAOFRIeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG4lcH/jFAG+AXR6T2K3dG
adJmdAWQKdDj71Ruoyefx5GSbD0B+rM1UcxOQgmZem2127RJgfDBBVYyjSwh7H1F
LRJdN6+NKReL2OW/HMnufvpVMvWICTWHInyvsqKqp+Yo4GC5z46OtsmzSayYgTaP
v2G9auC/rSUlzmQux9EAbTKDeNGMum3dt2rfsmnIDymBSHoPbizXF93/2hoo9jwx
BZQCq0nYBCa9pEdsmgvqKkb/Y5+CSFoe02qdUZFIuwh6qd/XPfeDPSu4O3z4J9g6
x8G+f7doeU0nzsAP+K0lG7ulAygxRHm5Bn2rwVdlYfihAuPNyF+Ua3duxBvjOBEY
7w/UQ64=
=ZWS9
-----END PGP SIGNATURE-----
Merge tag 'v5.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux into drm-next
Backmerge v5.11-rc5 into drm-next to clean up a bunch of conflicts we are dragging around.
Signed-off-by: Dave Airlie <airlied@redhat.com>
- A new DTS file for the Samsung GT-I9070 (Janice)
- Fix up ADC channel name attributes
- Add charger interrupts
- Add thermistors to the HREF boards
- Remove the non-existing AB8505 HW ADC IRQ
- Push down the VMMCI setting to each board
- Add the die temperature channel to teh AB8505
- Fix up the MMC host names to follow the standard
naming convention
-----BEGIN PGP SIGNATURE-----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=zDx3
-----END PGP SIGNATURE-----
Merge tag 'ux500-dts-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into arm/dt
Ux500 DTS updates for the v5.12 kernel cycle:
- A new DTS file for the Samsung GT-I9070 (Janice)
- Fix up ADC channel name attributes
- Add charger interrupts
- Add thermistors to the HREF boards
- Remove the non-existing AB8505 HW ADC IRQ
- Push down the VMMCI setting to each board
- Add the die temperature channel to teh AB8505
- Fix up the MMC host names to follow the standard
naming convention
* tag 'ux500-dts-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: Fix up MMC host node names
ARM: dts: ux500: Add die temperature to AB8505
ARM: dts: ux500: Push VMMCI down to each tree
ARM: dts: ux500: Remove the GPADC HW IRQ
ARM: dts: ux500: Add thermistors to the HREF
ARM: dts: ux500: Add interrupts to charger
ARM: dts: ux500: Fix channel names attributes
ARM: dts: ux500: Add a device tree for Janice
Link: https://lore.kernel.org/r/CACRpkdbn=P63V9aEO2wKu2DwvVUcbjwCEV_JvKwWZ0netT75ig@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The standard mandates that these nodes be named
mmc@... not sdi_foo@...
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
While the DT parser recognizes "ok" as a valid value for the
"status" property, it is actually mentioned nowhere. Use the
proper value "okay" instead, as done in the majority of files
already.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Link: https://lore.kernel.org/r/20200830191643.20717-1-freifunk@adrianschmutzler.de
[bjorn: Rebased and included fixup of sdx55-mtp]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This adds some additional DT labels which are handy when referring
to the nodes in derived DTS(I) files. It will also make the
definitions more consistent, e.g. by adding gsbi2_serial and
gsbi5_serial where we previously "only" had gsbi4_serial defined.
While at it, add missing spaces after some DT labels and remove one
useless empty line.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Link: https://lore.kernel.org/r/20200902165159.7733-1-freifunk@adrianschmutzler.de
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
ALFA Network AP120C-AC is a dual-band ceiling AP, based on Qualcomm
IPQ4018 + QCA8075 platform.
Specification:
- Qualcomm IPQ4018 (717 MHz)
- 256 MB of RAM (DDR3)
- 16 MB (SPI NOR) + 128 or 512 MB (SPI NAND) of flash
- 2x Gbps Ethernet, with 802.3af PoE support in one port
- 2T2R 2.4/5 GHz (IPQ4018), with ext. FEMs (QFE1952, QFE1922)
- 3x U.FL connectors
- 1x 1.8 dBi (Bluetooth) and 2x 3/5 dBi dual-band (Wi-Fi) antennas
- Atmel/Microchip AT97SC3205T TPM module (I2C bus)
- TI CC2540 Bluetooth LE module (USB 2.0 bus)
- 1x button (reset)
- 1x USB 2.0
- DC jack for main power input (12 V)
- UART header available on PCB (2.0 mm pitch)
This adds DTS for both the generic and custom Bit edition for Sartura.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Link: https://lore.kernel.org/r/20200909195640.3127341-4-robert.marko@sartura.hr
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Lets add labels to more commonly used nodes for easier modification in board DTS files.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Link: https://lore.kernel.org/r/20200909195640.3127341-2-robert.marko@sartura.hr
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Since we now have driver for the USB PHY, and USB controller is already supported by the DWC3 driver lets add the necessary nodes to DTSI.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200909163831.1894142-1-robert.marko@sartura.hr
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add support for pshold block to drive pshold towards the PMIC, which is
used to trigger a configurable event such as reboot or poweroff of the
SDX55 platform.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210118051005.55958-7-manivannan.sadhasivam@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The BreadBee and the BreadBee Crust are the same PCB with a different
SoC mounted. There are two top level dts to handle this.
To avoid deduplicating the parts that are more related to the PCB than
the SoC (i.e. the voltage regs and LEDs) add a common dtsi that can
be included in both top level dts.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Link: https://lore.kernel.org/r/20201224020354.2212037-1-daniel@0x0f.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- removing a property never documented nor used
- adding i2c recovery GPI for one more board
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEEAbEK3+sX+gUxe5RcpMrf1MU8doFAmAK5coACgkQcpMrf1MU
8druSxAAzhEzmkWMV9ApibcL9txr8FZcZQKIoML00mnfecxbS86xrR7YOrv078jK
lDkmxJ8NUJiYtU54q398jFeHyYQMQTcwu2q9/IwP/qC8vo+43DMR9uGZ7YiMN9j7
ERRmuvBF6tU5Gbr8BJ6w2Zn7I7V5HhXwq2oHnxvgHLZ7jH8z1THEUZgkD87I5wzX
oV0dEKznTaon0DsStcQMyMvnGlbsPHtYunc12hzfiMRPv961hX1mHG+yWqV/t86P
Zw87cIrCWzkBqE9bUK0JyB/ltIXfSk/28iRI+YOHSANmvx2sE4Ulss7g6qlacds0
g0MBRcCpteTw0ZM9wMClpsEzyWR961HAbehGakkTjmdpuEtd6fl03iAQHcEE6szN
xP5BEd6PS6auEmXf0yBa84tDnaOJ8D+13w5u0DiapMl4Wm85Y9ecl9gvmmkNJJ/4
mtZa5A8DkydFKBjfZwOYbzieVw2edN4rZQdRutnbXf4KuJw2phd0lV99TPSljYe1
DpI59quMr7txnlsCpd50FxNFb2wU4HRWDUv7k6g8YmQ2WgSxWuS/pyh8JJq/pL/U
R2ldSO2S/0CnxKi5tFN+TQWXxd2a+tnloIx7BmWsYGHazkk9A5yhrshsQMSvrzc6
xruSunjssd15gFLtMZiIAfQDPMPKvcZkRm4PzDcUx8B37gvWm6M=
=SfGI
-----END PGP SIGNATURE-----
Merge tag 'at91-dt-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/dt
AT91 DT for 5.12:
- removing a property never documented nor used
- adding i2c recovery GPI for one more board
* tag 'at91-dt-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: at91: sama5d2: remove atmel,wakeup-type references
ARM: dts: at91-sama5d27_wlsom1: add i2c recovery
Link: https://lore.kernel.org/r/20210122145056.171283-1-nicolas.ferre@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Ericsson U300 platform was one of two ARM929 based SoC platforms for
mobile phones in ST-Ericsson after the merger of Ericsson with ST-NXP
into ST-Ericsson, the other one being the ST Nomadik.
The platform was not widely adopted in Linux based systems and was
replaced with the far superior ST-Ericsson U8500 in 2011, but Linus
Walleij kept maintaining the code for the whole time.
Linus continues to use the Nomadik machine, but decided to drop
u300 from the kernel as part of this year's spring cleaning.
Thanks for having maintained it all these years.
Cc: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/lkml/CACRpkdbJkiHR9FSfJTH_5d_qRU1__dRXHM1TL40iqNRKbGQfrQ@mail.gmail.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The smp8758 (tango4) SoC was the last generation of set-top-box chips
to come out of Sigma Designs, and support was added by Marc Gonzalez
and Måns Rullgård between 2015 and 2017, before the company went out of
business and the products were abandoned.
The chip is used in some set-top-boxes such as the Popcorn Hour A-500,
which could have seen some adoption by hobbyists. This has not happened
in the past four years, and support for the more widely used MIPS based
SoCs was never merged at all.
Thanks to Marc and Måns for maintaining for the past years even after the
death of the platform.
Cc: Marc Gonzalez <marc.w.gonzalez@free.fr>
Cc: Mans Rullgard <mans@mansr.com>
Link: https://lore.kernel.org/lkml/2d643ebc-09af-a809-eb3f-2aec8ecee501@free.fr/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The ZTE ZX set-top-box SoC platform was added in 2015 by Jun Nie, with
Baoyou Xie and Shawn Guo subsequently becoming maintainers after the
addition of the 64-bit variant.
However, the only machines that were ever supported upstream are the
reference designs, not actual set-top-box devices that would benefit
from this support. All ZTE set-top-boxes from the past few years seem
to be based on third-party SoCs. While there is very little information
about zx296702 and zx296718 on the web, I found some references to other
chips from the same family, such as zx296716 and zx296719, which were
never submitted for upstream support. Finally, there is no support for
the GPU on either of them, with the lima and panfrost device drivers
having been added after work on the zx platform had stopped.
Shawn confirmed that he has not seen any interest in this platform for
the past four years, and that it can be removed.
Thanks to Jun and Shawn for maintaining this platform over the past
five years.
Cc: Jun Nie <jun.nie@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The SiRF Prima2 and Atlas platform code was contributed by Cambridge
Silicon Radio (CSR) after aquiring the original SiRF company, and
maintained by Barry Song. CSR was subsequently acquired by Qualcomm,
who no longer have an interest in maintaining the SoC platform but
instead have released more recent SoCs for the same market in the
Snapdragon family.
As Barry is no longer working for the company, nobody else there
wants to maintain it, and there are no third-party users, the
best way forward seems to be to completely remove it.
Thanks to Barry for maintaining the platform for the past ten years.
Cc: Barry Song <baohua@kernel.org>
Link: https://lore.kernel.org/lkml/c969392572604b98bcb3be44048c3165@hisilicon.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A test with the command below gives for example this error:
/arch/arm/boot/dts/rk3288-tinker.dt.yaml:
thermal-zones: 'cpu_thermal', 'gpu_thermal', 'reserve_thermal'
do not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-]{1,12}-thermal$', 'pinctrl-[0-9]+'
Rename Rockchip rk3288 thermal subnodes
so that it ends with "-thermal"
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/
thermal/thermal-zones.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210117150953.16475-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The CPU thermal zone is called on most of the older DTSI cpu_thermal.
However, the underscore is an invalid character for a node name and the
thermal zone binding explicitly requires that zones are called
*-thermal. Let's fix it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20210114113538.1233933-8-maxime@cerno.tech
The pwm-backlight binding requires a power supply. Make sure we provide
one.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20210114113538.1233933-7-maxime@cerno.tech
According to the LED bindings, the LED node names are supposed to be led
plus an optional suffix. Let's fix our users to use that new scheme.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20210114113538.1233933-6-maxime@cerno.tech
Here are few more late changes that would be nice to get into v5.11:
- More updates to use cpsw switchdev driver
- Enable gta04 PMIC power management
- Updates for dra7 for ECC support, 1.8GHz speed and keep the
ldo0 regulator always on as specified in the data manual
-----BEGIN PGP SIGNATURE-----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=XKaK
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.11/dt-late-signed' into omap-for-v5.12-dt
Late devicetree changes for omaps for v5.11 merge window
Here are few more late changes that would be nice to get into v5.11:
- More updates to use cpsw switchdev driver
- Enable gta04 PMIC power management
- Updates for dra7 for ECC support, 1.8GHz speed and keep the
ldo0 regulator always on as specified in the data manual
The PHY address bit 2 is configured by the LED pin. Attaching a LED
to this pin is not sufficient to guarantee this configuration pin is
correctly read. This leads to some platforms having their PHY at
address 0 and others at address 4.
If there is no phy-handle specified, the FEC driver will scan the PHY
bus for a PHY and use that. Consequently, adding the DT configuration
of the PHY and the phy properties to the FEC driver broke some boards.
Fix this by removing the phy-handle property, and listing two PHY
entries for both possible PHY addresses, so that the DT configuration
for the PHY can be found by the PHY driver.
Fixes: 86b08bd5b9 ("ARM: dts: imx6-sr-som: add ethernet PHY configuration")
Reported-by: Christoph Mattheis <christoph.mattheis@arcor.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is another uart next to the console uart used by vendor uboot and
kernel, enable it and document its location.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Configuration was correct enough to work with the pre-configuration done by
uboot. While at it, also document the location.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is another uart next to the console uart used by vendor uboot and
kernel, enable it and document its location.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Configuration was correct enough to work with the pre-configuration done by
uboot. While at it, also document the location.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
RTC pcf2127 device driver has changed default behaviour of the watchdog
feature in v5.11-rc1. Now you need to explicitly enable it with a
device tree property, "reset-source", when used in the board design.
Fixes: 71ac13457d ("rtc: pcf2127: only use watchdog when explicitly available")
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Cc: Bruno Thomsen <bth@kamstrup.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
VICTGO is the Kverneland TGO IsoBus universal terminal for agricultural
applications on tractors
Co-Developed-by: David Jander <david@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
VICUT1(Q,P) is the Kverneland UT1(Q,P) IsoBus universal terminal for agricultural
applications on tractors.
Co-Developed-by: David Jander <david@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds a device-tree definition for the CSI0 MCLK pin,
which can be used for feeding MIPI CSI-2 sensors.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
There are two KSZ8081 on the imx6ul-14x14-evk: one has the reset line
controlled by the Q1 output of the 74LV595PW expander, and the other
by the Q2 output.
The KSZ8081 datasheet states that the tsr parameter (Stable supply
voltage (VDDIO, VDDA_3.3) to reset high) to be 10ms minimum and
"After the de-assertion of reset, wait a minimum of 100 µs before
starting programming on the MIIM (MDC/MDIO) interface."
Describe these parameters in the devicetree.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently the 74LV595PW GPIO expander is not functional because its OE
pin is not driven low.
Make it funcional by passing the 'enable-gpios' property inside the
GPIO expander node.
After putting the OE pin in low state, the outputs of the 74LV595PW all
go low.
The two KSZ8081 Ethernet PHYs reset lines are driven from the
the GPIO expander and as they remain low, this causes the Ethernet
PHYs not to be detected.
There is one solution to this problem as suggested by Andrew Lunn:
"Some devices will respond to MDIO while held in reset, some don't.
If your PHYs don't you need to add a compatible of the form
ethernet-phy-id[a-f0-9]{4}\\.[a-f0-9]{4}$ with the PHY ID. The PHY
will then be probed, independent of if it can be found on the bus or
not, and that probing will enable the GPIO."
So pass the "ethernet-phy-id0022.1560" for the KSZ8081 PHYs so that they
both can be functional after 74LV595PW is activated.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GPIO expander SPI chipselect is active low. Mark it as such to avoid
the following warning:
[ 6.839213] gpio@0 enforce active low on chipselect handle
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is no firmware to initialize the arch timer register on all iMX7
systems, add arm,cpu-registers-not-fw-configured to let Linux do it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Ux500 platforms have some memory carveouts set aside for
communicating with the modem and for the initial secure software
(ISSW). These areas are protected by the memory controller
and will result in an external abort if accessed like common
read/write memory.
On the legacy boot loaders, these were set aside by using
cmdline arguments such as this:
mem=96M@0 mem_mtrace=15M@96M mem_mshared=1M@111M
mem_modem=16M@112M mali.mali_mem=32M@128M mem=96M@160M
hwmem=127M@256M mem_issw=1M@383M mem_ram_console=1M@384M
mem=638M@385M
Reserve the relevant areas in the device tree instead. The
"mali", "hwmem", "mem_ram_console" and the trailing 1MB at the
end of the memory reservations in the list are not relevant for
the upstream kernel as these are nowadays replaced with
upstream technologies such as CMA. The modem and ISSW
reservations are necessary.
This was manifested in a bug that surfaced in response to
commit 7fef431be9 ("mm/page_alloc: place pages to tail in __free_pages_core()")
which changes the behaviour of memory allocations
in such a way that the platform will sooner run into these
dangerous areas, with "Unhandled fault: imprecise external
abort (0xc06) at 0xb6fd83dc" or similar: the real reason
turns out to be that the PTE is pointing right into one of
the reserved memory areas. We were just lucky until now.
We need to augment the DB8500 and DB8520 SoCs similarly
and also create a new include for the DB9500 used in the
Snowball since this does not have a modem and thus does
not need the modem memory reservation, albeit it needs
the ISSW reservation.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Cc: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/20201213225517.3838501-1-linus.walleij@linaro.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Fix backlight pwm on imx6qdl-kontron-samx6i which is lost from
#pwm-cells conversion.
- Fix duplicated bus node name for i.MX8MN SoC.
- Fix reset register offset on LS1028A SoC.
- Rename MMC node aliases for imx6q-tbs2910 to keep the MMC device
index consistent with previous kernel version.
- Selecting ARM_GIC_V3 on non-CP15 processors to fix one build failure
with i.MX8M SoC driver.
- Fix typos with status property on imx6qdl-kontron-samx6i board.
- Fix duplicated regulator-name on imx6qdl-gw52xx board.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl/9n4AUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM5pmQf+O0hRAVWaMXk4SCs/CsQ4Z6XNPSfz
7DSnkz0Rg53uykv+oe57sryBHGI46vy/hJeD6/OX4XgnlxaKXwmdaE+sek85D01h
C/Gzg7lKDvr8vWKZcOzhTQhs9F+EuHSsS2zW9StUBBSlXx3r2h9f+kJOLihFwvQp
CCWU+eGXgRIqZme5tIX9tFqPP1PmNRfIbZWgLwx9e/foCMl64fJSIe45ik4WePeV
+WCB3xMP38q2bfhZQv164uIw8m5/nEb8dp9O+zNamy/RN1hQqRaq1sPAwrjcqs2z
whaVS3iaGRM/RyAdbxy1JCxM+yDNM0Vnby/txVgsEOE+a9mfl2D2upQ1NA==
=+e1G
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.11:
- Fix backlight pwm on imx6qdl-kontron-samx6i which is lost from
#pwm-cells conversion.
- Fix duplicated bus node name for i.MX8MN SoC.
- Fix reset register offset on LS1028A SoC.
- Rename MMC node aliases for imx6q-tbs2910 to keep the MMC device
index consistent with previous kernel version.
- Selecting ARM_GIC_V3 on non-CP15 processors to fix one build failure
with i.MX8M SoC driver.
- Fix typos with status property on imx6qdl-kontron-samx6i board.
- Fix duplicated regulator-name on imx6qdl-gw52xx board.
* tag 'imx-fixes-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6qdl-gw52xx: fix duplicate regulator naming
ARM: dts: imx6qdl-kontron-samx6i: fix i2c_lcd/cam default status
ARM: imx: fix imx8m dependencies
ARM: dts: tbs2910: rename MMC node aliases
arm64: dts: ls1028a: fix the offset of the reset register
arm64: dts: imx8mn: Fix duplicate node name
ARM: dts: imx6qdl-kontron-samx6i: fix pwms for lcd-backlight
Link: https://lore.kernel.org/r/20210112131224.GI28365@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
I didn't touch this code since it served as a platform to introduce
ARMv7-M support to Linux. The only known machine that runs Linux has only
4 MiB of RAM (that originally only exists to hold the display's framebuffer).
There are no known users and no further use foreseeable, so drop the
code.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20210115155130.185010-2-u.kleine-koenig@pengutronix.de'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The PicoITX has only one ethernet routed out, so the KS8851 is not used
at all. Disable the KS8851 and the entire FMC controller.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The node names for devices using the pwm-leds driver follow a certain
naming scheme (now). Parent node name is not enforced, but recommended
by DT project.
DTC arch/arm/boot/dts/stm32mp157c-lxa-mc1.dt.yaml
CHECK arch/arm/boot/dts/stm32mp157c-lxa-mc1.dt.yaml
/home/alex/build/linux/arch/arm/boot/dts/stm32mp157c-lxa-mc1.dt.yaml: led-rgb: 'led-blue', 'led-green', 'led-red' do not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: /home/alex/src/linux/leds/Documentation/devicetree/bindings/leds/leds-pwm.yaml
Signed-off-by: Alexander Dahl <post@lespocky.de>
Acked-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The STM32MP1 DHCOM SoM can be built with either bus voltage level shifter
or without one on the SDMMC1 interface. Because the SDMMC1 interface is
limited to 50 MHz and hence SD high-speed anyway, disable the SD feedback
clock to permit operation of the same U-Boot image on both SoM with and
without voltage level shifter.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The default state of SD bus and clock line is logical HI. SD card IO is
open-drain and pulls the bus lines LO. Always enable the SD bus pull ups
to guarantee this behavior on DHCOM SoM. Note that on SoMs with SD bus
voltage level shifter, the pull ups are built into the level shifter,
however that has no negative impact.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The GPIO hog flags are ignored by gpiolib-of.c now, set the flags to 0.
Since GPIO_ACTIVE_HIGH is defined as 0, this change only increases the
correctness of the DT.
Fixes: fde180f06d ("ARM: dts: stm32: Add DHSOM based DRC02 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The GPIO hog flags are ignored by gpiolib-of.c now, set the flags to 0.
Due to a change in gpiolib-of.c, setting flags to GPIO_ACTIVE_LOW and
using output-low DT property leads to the GPIO being set high instead.
Fixes: ac68793f49 ("ARM: dts: stm32: Add DHCOM based PicoITX board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The GPIO hog node name should match regex '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$',
make it so and fix the following two make dtbs_check warnings:
arch/arm/boot/dts/stm32mp157c-dhcom-picoitx.dt.yaml: hog-usb-port-power: $nodename:0: 'hog-usb-port-power' does not match '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$'
arch/arm/boot/dts/stm32mp153c-dhcom-drc02.dt.yaml: hog-usb-hub: $nodename:0: 'hog-usb-hub' does not match '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$'
Fixes: ac68793f49 ("ARM: dts: stm32: Add DHCOM based PicoITX board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The DRC02 has no use for the on-SoM touchscreen controller, and the
on-SoM touchscreen controller may not even be populated, which then
results in error messages in kernel log. Disable the touchscreen
controller in DT.
Fixes: fde180f06d ("ARM: dts: stm32: Add DHSOM based DRC02 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The DHCOM SoM uSD slot card detect signal is connected to GPIO PG1,
describe it in the DT.
Fixes: 34e0c7847d ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The uSD card detect signal on the DH DRC02 is active-high, with
a default pull down resistor on the board. Invert the polarity.
Fixes: fde180f06d ("ARM: dts: stm32: Add DHSOM based DRC02 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
--
Note that this could not be tested on prototype SoMs, now that it is
tested, this issue surfaced, so it needs to be fixed.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The AB8505 mixed signal ASIC variant has a die temperature
channel that is missing in the AB8500 variant. Add it to
the DTSI.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The setting of VMMCI differs so much between different
boards that we need to handle it on a per-board basis
rather that complicating things by overriding stuff from
the included DTSI:s. Push it down into top-level tree
instead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the two temperature-monitoring thermistors to the
HREF reference design, defines a thermal zone for the
chassis and sets some reasonable thermal limits.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The different charger nodes in the AB8500 and AB8505
includes was missing the interrupt assignments for the
interrupts necessary to drive the AB8500/AB8505 charging
state machine.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The AB8500/AB8505 is providing ADC channels and do so
using the standard property "io-channel-names" not the
mistakenly singular form "io-channel-name".
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The A10s/A13 mali gpu was not defined in device tree
Add A10 mali gpu as a fallback for A10s/A13
Tested with Olimex-A13-SOM / Olimex-A13-OlinuXino-MICRO
"kmscube" 3d cube on screen (60fps / 10%cpu)
Versions: Lima:1.1.0 EGL:1.4 OpenGLES:2.0 Mesa:20.2.2
Signed-off-by: Sergio Sota <sergiosota@fanamoel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210108103819.322901-1-sergiosota@fanamoel.com
In preparation for the conversion of the DWC HDMI TX device tree
bindings to YAML, move the HDMI encoder's 'port' nodes under a 'ports'
node. The 'ports' node is optional in the OF graph implementation, but
YAML bindings require it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
to be consistent with kernel versions up to v5.9 (mmc aliases not used here).
usdhc1 is not wired up on this board and therefore cannot be used.
Start mmc aliases with usdhc2.
Signed-off-by: Soeren Moch <smoch@web.de>
Cc: stable@vger.kernel.org # 5.10.x
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The wlf,wm8962 driver does not use the clock-names property.
Drop it.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
With the conversion of syscon.yaml minItems for compatibles
was set to 2. Current Rockchip dtsi files only use "syscon" for
QoS registers. Add Rockchip QoS compatibles for rk3288
to reduce notifications produced with:
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/mfd/syscon.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20201206103711.7465-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
With the conversion of syscon.yaml minItems for compatibles
was set to 2. Current Rockchip dtsi files only use "syscon" for
QoS registers. Add Rockchip QoS compatibles for rk3066/rk3188
to reduce notifications produced with:
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/mfd/syscon.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20201206103711.7465-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
These are a small number of bug fixes that all came in before or during
the merge window, most for the omap platform:
- One boot regression fix for Nokia N9 (OMAP3).
- Two small defconfig changes for omap2, to reflect changes in drivers
- Warning fixes for DT issues on omap2, picoxcell and bitmap SoCs.
The picoxcell platform will be removed in v5.12, but fixing it
first makes it easier to backport to the fix to stable kernels
and get a clean build with new dtc versions
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAl/4j/QACgkQmmx57+YA
GNmQHg//S1z56rKC8Qj3xiMSVCeK/Imua0i1ZDRFsXMdT4X7CSyWuJCpFosrKC0T
cN9By1FozJOpXZZtDsRHjvEhtYayhoBMtilRfzUys7Zl4WsDCgVThrtWe3h8mCxu
xiluR62IIiC1FGfNn7QBBBDkov+35i8qu2LZaAkvYEYGxuI58reyZb6+EOUzLfRB
1LCTz1/SaGV43hwyr5CUmfsybnDfy6HiG/WFrZlve7yRRvkjY0h9oJL4EstLMLZx
dHOCj8xkzCHd1qA66L4jz731TDPqupXZAJjoHB/eTG0Wuv0mcs4vb7SKY0psOaNU
rSgc4kRPQ5w/8Bqed23fTjUCaNQTDQ8NoPKKFi2vUhO9iJ9Cptd9Id6HyiWU7URP
ShmS4YxKQZjmJA8TjycUYsTnMVQGSCW2iWorUJ5Z2k8RW0EgLwSSbJbkoxrgv1zh
D5lqKotJZh+QpC68a8kUqfMsq9LpfAWOuAsE71CxuJrL0TXNDgvVS9YXq8b+E/3b
Tqvkt7tY+KNHk0FaB8hratNqTMIH3r5T4TAWERKFutqQRFRJalgBqwWyqD6aimgz
lfAARXXw1A+2NrDw9a2CeGAOFt7lPBJ/2SGppJWTNwo7HsXeK+Xm0qxAC9oIwFxK
RQP8pxelp25C3jlsViFpTXKaWHBgg372x4voQLXh0ECcgW5A5Pg=
=gv6R
-----END PGP SIGNATURE-----
Merge tag 'arm-fixes-5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"These are a small number of bug fixes that all came in before or
during the merge window, most for the omap platform:
- One boot regression fix for Nokia N9 (OMAP3).
- Two small defconfig changes for omap2, to reflect changes in
drivers
- Warning fixes for DT issues on omap2, picoxcell and bitmap SoCs.
The picoxcell platform will be removed in v5.12, but fixing it
first makes it easier to backport to the fix to stable kernels and
get a clean build with new dtc versions"
* tag 'arm-fixes-5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: picoxcell: fix missing interrupt-parent properties
ARM: dts: ux500/golden: Set display max brightness
arm64: dts: bitmain: Use generic "ngpios" rather than "snps,nr-gpios"
ARM: omap2: pmic-cpcap: fix maximum voltage to be consistent with defaults on xt875
ARM: omap2plus_defconfig: enable SPI GPIO
ARM: OMAP2+: omap_device: fix idling of devices during probe
ARM: dts: OMAP3: disable AES on N950/N9
ARM: omap2plus_defconfig: drop unused POWER_AVS option
PicoXcell has had nothing but treewide cleanups for at least the last 8
years and no signs of activity. The most recent activity is a yocto vendor
kernel based on v3.0 in 2015.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Jamie Iles <jamie@jamieiles.com>
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20201210200315.2965567-2-robh@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
dtc points out that the interrupts for some devices are not parsable:
picoxcell-pc3x2.dtsi:45.19-49.5: Warning (interrupts_property): /paxi/gem@30000: Missing interrupt-parent
picoxcell-pc3x2.dtsi:51.21-55.5: Warning (interrupts_property): /paxi/dmac@40000: Missing interrupt-parent
picoxcell-pc3x2.dtsi:57.21-61.5: Warning (interrupts_property): /paxi/dmac@50000: Missing interrupt-parent
picoxcell-pc3x2.dtsi:233.21-237.5: Warning (interrupts_property): /rwid-axi/axi2pico@c0000000: Missing interrupt-parent
There are two VIC instances, so it's not clear which one needs to be
used. I found the BSP sources that reference VIC0, so use that:
https://github.com/r1mikey/meta-picoxcell/blob/master/recipes-kernel/linux/linux-picochip-3.0/0001-picoxcell-support-for-Picochip-picoXcell-SoC.patch
Acked-by: Jamie Iles <jamie@jamieiles.com>
Link: https://lore.kernel.org/r/20201230152010.3914962-1-arnd@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
UAPI Changes:
- Not necessarily one, but we document that userspace needs to force probe connectors.
Cross-subsystem Changes:
- Require FB_ATY_CT for aty on sparc64.
- video: Fix documentation, and a few compiler warnings.
- Add devicetree bindings for DP connectors.
- dma-buf: Update kernel-doc, and add might_lock for resv objects in begin/end_cpu_access.
Core Changes:
- ttm: Warn when releasing a pinned bo.
- ttm: Cleanup bo size handling.
- cma-helper: Remove prime infix, and implement mmap as GEM CMA functions.
- Split drm_prime_sg_to_page_addr_arrays into 2 functions.
- Add a new api to install irq using devm.
- Update panel kerneldoc to inline style.
- Add DP support to drm/bridge.
- Assorted small fixes to ttm, fb-helper, scheduler.
- Add atomic_commit_setup function callback.
- Automatically use the atomic gamma_set, instead of forcing drivers to declare the default atomic version.
- Allow using degamma for legacy gamma if gamma is not available.
- Clarify that primary/cursor planes are not tied to 1 crtc (depending on possible_crtcs).
- ttm: Cleanup the lru handler.
Driver Changes:
- Add pm support to ingenic.
- Assorted small fixes in radeon, via, rockchip, omap2fb, kmb, gma500, nouveau, virtio, hisilicon, ingenic, s6e63m0 panel, ast, udlfb.
- Add BOE NV110WTM-N61, ys57pss36bh5gq, Khadas TS050 panels.
- Stop using pages with drm_prime_sg_to_page_addr_arrays, and switch all callers to use ttm_sg_tt_init.
- Cleanup compiler and docbook warnings in a lot of fbdev devices.
- Use the drmm_vram_helper in hisilicon.
- Add support for BCM2711 DSI1 in vc4.
- Add support for 8-bit delta RGB panels to ingenic.
- Add documentation on how to test vkms.
- Convert vc4 to atomic helpers.
- Use degamma instead of gamma table in omap, to add support for CTM and color encoding/range properties.
- Rework omap DSI code, and merge all omapdrm modules now that the last omap panel is now a drm panel.
- More refactoring of omap dsi code.
- Enable 10/12 bpc outputs in vc4.
-----BEGIN PGP SIGNATURE-----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=orEC
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2020-12-17' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.12:
UAPI Changes:
- Not necessarily one, but we document that userspace needs to force probe connectors.
Cross-subsystem Changes:
- Require FB_ATY_CT for aty on sparc64.
- video: Fix documentation, and a few compiler warnings.
- Add devicetree bindings for DP connectors.
- dma-buf: Update kernel-doc, and add might_lock for resv objects in begin/end_cpu_access.
Core Changes:
- ttm: Warn when releasing a pinned bo.
- ttm: Cleanup bo size handling.
- cma-helper: Remove prime infix, and implement mmap as GEM CMA functions.
- Split drm_prime_sg_to_page_addr_arrays into 2 functions.
- Add a new api to install irq using devm.
- Update panel kerneldoc to inline style.
- Add DP support to drm/bridge.
- Assorted small fixes to ttm, fb-helper, scheduler.
- Add atomic_commit_setup function callback.
- Automatically use the atomic gamma_set, instead of forcing drivers to declare the default atomic version.
- Allow using degamma for legacy gamma if gamma is not available.
- Clarify that primary/cursor planes are not tied to 1 crtc (depending on possible_crtcs).
- ttm: Cleanup the lru handler.
Driver Changes:
- Add pm support to ingenic.
- Assorted small fixes in radeon, via, rockchip, omap2fb, kmb, gma500, nouveau, virtio, hisilicon, ingenic, s6e63m0 panel, ast, udlfb.
- Add BOE NV110WTM-N61, ys57pss36bh5gq, Khadas TS050 panels.
- Stop using pages with drm_prime_sg_to_page_addr_arrays, and switch all callers to use ttm_sg_tt_init.
- Cleanup compiler and docbook warnings in a lot of fbdev devices.
- Use the drmm_vram_helper in hisilicon.
- Add support for BCM2711 DSI1 in vc4.
- Add support for 8-bit delta RGB panels to ingenic.
- Add documentation on how to test vkms.
- Convert vc4 to atomic helpers.
- Use degamma instead of gamma table in omap, to add support for CTM and color encoding/range properties.
- Rework omap DSI code, and merge all omapdrm modules now that the last omap panel is now a drm panel.
- More refactoring of omap dsi code.
- Enable 10/12 bpc outputs in vc4.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/78381a4f-45fd-aed4-174a-94ba051edd37@linux.intel.com
R40 contains deinterlace core compatible to that in H3. One peculiarity
is that RAM gate is shared with CSI1. User manual states it's separate
but that's not true. Shared gate was verified with BSP Linux code check
and with runtime tests (CPU crashed if CSI1 gate was not ungated).
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210106181901.1324075-3-jernej.skrabec@siol.net
Plymovent BAS is a base system controller produced for the Plymovent filter
systems.
Co-Developed-by: David Jander <david@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Plymovent M2M is a control interface produced for the Plymovent filter
systems.
Co-Developed-by: David Jander <david@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add qpic_nand node to support QPIC NAND controller on SDX55 platform.
Since there is no "aon" clock in SDX55, a dummy clock is provided.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210106125322.61840-11-manivannan.sadhasivam@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add a node for the ARM SMMU found in the SDX55.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210106125322.61840-7-manivannan.sadhasivam@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add devicetree support for SDHCI controller found in Qualcomm SDX55
platform. The SDHCI controller is based on the MSM SDHCI v5 IP.
Hence, the support is added by reusing the existing sdhci driver with
"qcom,sdhci-msm-v5" as the fallback.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210106125322.61840-5-manivannan.sadhasivam@linaro.org
[bjorn: added include of qcom,gcc-sdx55.h]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The SL631 is a family of Allwinner V3 action cameras sold under
various names, such as SJCAM SJ4000 Air or F60 Action Camera.
Devices in this family share a common board design but can be found
with different image sensors, including the IMX179 and the OV4689.
This adds support for a common dtsi for the SL631 family as well as
a specific dts for the IMX179 fashion, which will later be populated
with an IMX179 node when a driver is available.
Features that were tested on the device include:
- UART debug
- MMC
- USB peripheral (e.g. g_ether)
- Buttons
- SPI NOR flash
Note that the exact designer/vendor of these boards is unknown.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201206165131.1041983-6-contact@paulk.fr
Arnd Bergmann
Rosen Penev
Amelie Delaunay
Jagan Teki
Russell King
Shawn Guo
Florian Fainelli
Maxime Ripard
Rob Herring
Alexander Shiyan
Javier Martinez Canillas
Adam Ford
Carl Philipp Klemm
Tony Lindgren
André Hentschel
Johan Jonker
Robin Murphy
Stanislav Jakubek
Nicolas Saenz Julienne
Dave Stevenson
Martin Blumenstingl
Robert Marko
Marek Vasut
Serge Semin
Dave Airlie
Linus Walleij
Adrian Schmutzler
John Crispin
Jonathan McDowell
Manivannan Sadhasivam
Daniel Palmer
Claudiu Beznea
Nicolas Ferre
Alexey Minnekhanov
Yifeng Zhao
Joakim Zhang
Andreas Kemnade
Bruno Thomsen
Oleksij Rempel
Paul Kocialkowski
Fabio Estevam
Uwe Kleine-König
Alexander Dahl
Sergio Sota
Koen Vandeputte
Laurent Pinchart
Marco Felsch
Soeren Moch
Demetris Ierokipides
Linus Torvalds
Dinh Nguyen
Daniel Vetter
Jernej Skrabec
Mans Rullgard
Vinod Koul
Bjorn Andersson
Michael Klein