The PFVF protocol defines messages composed of a number of control
bitfields. Replace all the code setting and retrieving such bits
with the utilities from bitfield.h, to improve code quality and
readability.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This implementation of the PFVF protocol was designed around the GEN2
devices and its CSR format. In order to support future generations,
which come with differently sized fields, change the definition of the PFVF
message and make it abstract by means of a new pfvf_message struct. Also,
introduce some utilities to translate to and from the new message format
and the device specific CSR format.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In this implementation of the PFVF protocol every egressing message must
include the ADF_PFVF_MSGORIGIN_SYSTEM flag. However, this flag can be set
on all the outbound messages just before sending them rather than at
message build time, as currently done.
Remove the unnecessary code duplication by setting the
ADF_PFVF_MSGORIGIN_SYSTEM flag only once at send time in
adf_gen2_pfvf_send().
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Currently PF and VF share the same send and receive logic for the PFVF
protocol. However, the inner behaviour still depends on the specific
direction, requiring a test to determine the if the sender is a PF or a
VF. Moreover the vf_nr parameter is only required for PF2VF messages and
ignored for the opposite direction.
Make the GEN2 send and recv completely direction agnostic, by calculating
and determining any direction specific input in the caller instead, and
feeding the send and the receive functions with the same arguments for
both PF and VF. In order to accommodate for this change, the API of the
pfvf_ops send and recv has been modified to remove any reference to vf_nr.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Currently PFVF messages are created upfront in the CSR format, that is
PF2VF messages starting from bit 0 and VF2PF from bit 16, and passed
along unmodified to the PFVF send function.
Refactor the code to allow the VF2PF messages to be built starting from
bit 0, as for the PF2VF messages. Shift the VF to PF messages just
before sending them, and refactor the send logic to handle messages
properly depending on the direction.
As a result all the messages are composed the same way regardless of
the direction.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add and use the new helper function adf_get_pmisc_base() where convenient.
Also:
- remove no longer shared variables
- leverage other utilities, such as GET_PFVF_OPS(), as a consequence
- consistently use the "pmisc_addr" name for the returned value of this
new helper
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for triggering a HW reset of a specific ring pair.
Being a device specific feature, add it to the hw_device_data struct.
This feature is supported only by QAT GEN4 devices.
This patch is based on earlier work done by Zelin Deng.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Extended the capability detection logic for 4xxx devices.
Mask out unsupported algorithms and services based on the value read in
the fuse register.
This includes only capabilities for the crypto service.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Reviewed-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Enhance the device capability detection for QAT GEN2 devices to detect if
a device supports the compression service.
This is done by checking both the fuse and the strap registers for c62x
and c3xxx and only the fuse register for dh895xcc.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Reviewed-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Set the CIPHER capability for QAT GEN2 devices if the hardware supports
it. This is done if both the CIPHER and the AUTHENTICATION engines are
available on the device.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Reviewed-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Get compression extended capabilities mask from firmware through the
init/admin channel.
These capabilities are stored in the accel_dev structure and will be
communicated to VF through the PFVF channel.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Reviewed-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Give the same priority of OMAP DES/3DES than OMAP AES for being sure it
is picked before software implementation.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Enable deflate/lz77_zstd algorithm for uacce device on Kunpeng930.
Signed-off-by: Yang Shen <shenyang39@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If the hardware reports the 'CQ' overflow or 'CQE' error by the abnormal
interrupt, disable the queue and stop tasks send to hardware.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If the hardware reports the event queue overflow by the abnormal interrupt,
the driver needs to reset the function and re-enable the event queue
interrupt and abnormal interrupt.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The abnormal interrupt method needs to be changed, and the changed method
needs to be locked in order to maintain atomicity. Therefore,
replace request_irq() with request_threaded_irq().
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
After processing an interrupt event and the interrupt function is
enabled by writing the QM_DOORBELL_CMD_AEQ register, the hardware
may generate new interrupt events due to processing other user's task
when the subsequent interrupt events have not been processed. The new
interrupt event will disrupt the current normal processing flow and
cause other problems.
Therefore, the operation of writing the QM_DOORBELL_CMD_AEQ doorbell
register needs to be placed after all interrupt events processing
are completed.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch does not change any code, just code movement. Preparing for
next patch.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The internal memory of the device needs to be reset only when
the device is globally initialized. Other scenarios, such as
function reset, do not need to perform reset.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When remove the driver and executing the task occur at the same time,
the following deadlock will be triggered:
Chain exists of:
sva_lock --> uacce_mutex --> &qm->qps_lock
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&qm->qps_lock);
lock(uacce_mutex);
lock(&qm->qps_lock);
lock(sva_lock);
And the lock 'qps_lock' is used to protect qp. Therefore, it's reasonable
cycle is to continue until the qp memory is released. So move the release
lock infront of 'uacce_remove'.
Signed-off-by: Yang Shen <shenyang39@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
For Kunpeng 920, the bit 0 of register 'HZIP_SGL_RUSER_32_63' stand for
whether the ssid is valid. So this bit should be set as valid for sva mode.
Signed-off-by: Yang Shen <shenyang39@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
hpre_curve25519_src_init() allocates memory for 'ptr' before calling
memcmp(). If memcmp() returns 0, the function will return '-EINVAL'
without freeing memory.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use 2-factor multiplication argument form kcalloc() instead
of kzalloc().
Link: https://github.com/KSPP/linux/issues/162
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use 2-factor multiplication argument form kcalloc() instead
of kzalloc().
Link: https://github.com/KSPP/linux/issues/162
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add new module parameter to allow users to use SEV_INIT_EX instead of
SEV_INIT. This helps users who lock their SPI bus to use the PSP for SEV
functionality. The 'init_ex_path' parameter defaults to NULL which means
the kernel will use SEV_INIT, if a path is specified SEV_INIT_EX will be
used with the data found at the path. On certain PSP commands this
file is written to as the PSP updates the NV memory region. Depending on
file system initialization this file open may fail during module init
but the CCP driver for SEV already has sufficient retries for platform
initialization. During normal operation of PSP system and SEV commands
if the PSP has not been initialized it is at run time. If the file at
'init_ex_path' does not exist the PSP will not be initialized. The user
must create the file prior to use with 32Kb of 0xFFs per spec.
Signed-off-by: David Rientjes <rientjes@google.com>
Co-developed-by: Peter Gonda <pgonda@google.com>
Signed-off-by: Peter Gonda <pgonda@google.com>
Reviewed-by: Marc Orr <marcorr@google.com>
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Brijesh Singh <brijesh.singh@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Marc Orr <marcorr@google.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Rientjes <rientjes@google.com>
Cc: John Allen <john.allen@amd.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: linux-crypto@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add psp_init_on_probe module parameter that allows for skipping the
PSP's SEV platform initialization during module init. User may decouple
module init from PSP init due to use of the INIT_EX support in upcoming
patch which allows for users to save PSP's internal state to file. The
file may be unavailable at module init.
Also moves the PSP ABI version log message to after successful PSP init
instead of module init in case this new parameter is used.
Signed-off-by: Peter Gonda <pgonda@google.com>
Acked-by: Brijesh Singh <brijesh.singh@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Marc Orr <marcorr@google.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Rientjes <rientjes@google.com>
Cc: John Allen <john.allen@amd.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: linux-crypto@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Create a helper function sev_fw_alloc() which can be used to allocate
aligned memory regions for use by the PSP firmware. Currently only used
for the SEV-ES TMR region but will be used for the SEV_INIT_EX NV memory
region.
Signed-off-by: Peter Gonda <pgonda@google.com>
Reviewed-by: Marc Orr <marcorr@google.com>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Brijesh Singh <brijesh.singh@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Marc Orr <marcorr@google.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Rientjes <rientjes@google.com>
Cc: John Allen <john.allen@amd.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: linux-crypto@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move the data corrupted retry of SEV_INIT into the
__sev_platform_init_locked() function. This is for upcoming INIT_EX
support as well as helping direct callers of
__sev_platform_init_locked() which currently do not support the
retry.
Signed-off-by: Peter Gonda <pgonda@google.com>
Reviewed-by: Marc Orr <marcorr@google.com>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Acked-by: Brijesh Singh <brijesh.singh@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Marc Orr <marcorr@google.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Rientjes <rientjes@google.com>
Cc: John Allen <john.allen@amd.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: linux-crypto@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Currently only the firmware error code is printed. This is incomplete
and also incorrect as error cases exists where the firmware is never
called and therefore does not set an error code.
Signed-off-by: Peter Gonda <pgonda@google.com>
Reviewed-by: Marc Orr <marcorr@google.com>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Acked-by: Brijesh Singh <brijesh.singh@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Marc Orr <marcorr@google.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Rientjes <rientjes@google.com>
Cc: John Allen <john.allen@amd.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: linux-crypto@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The QAT driver does not have support for PFVF interrupts for GEN4
devices, therefore report the vf2pf sources as 0.
This prevents a NULL pointer dereference in the function
adf_msix_isr_ae() if the device triggers a spurious interrupt.
Fixes: 993161d36a ("crypto: qat - fix handling of VF to PF interrupts")
Reported-by: Adam Guerin <adam.guerin@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When hisi_qm_resume() returns 0, it indicates that the device has started
successfully. If the device fails to start, hisi_qm_resume() needs to
return the actual error code to the caller instead of 0.
Fixes: d7ea53395b ("crypto: hisilicon - add runtime PM ops")
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Added devlink parameters to create and delete custom CPT engine groups.
Example:
devlink dev param set pci/0002:20:00.0 name egrp_create value \
"se:32;se.out" cmode runtime
devlink dev param set pci/0002:20:00.0 name egrp_delete value \
"egrp:1" cmode runtime
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Shijith Thotton <sthotton@marvell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Octeon TX2 CPT has three type of engines to handle symmetric, asymmetric
and ipsec specific workload. For better utilization, these engines can
be grouped to custom groups at runtime.
This patch adds APIs to create and delete custom CPT engine groups.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Shijith Thotton <sthotton@marvell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
We should not call pm_runtime_resume_and_get where the reference
count is expected to be incremented unconditionally. This patch
reverts these calls to the original unconditional get_sync call.
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: 747bf30fd9 ("crypto: stm32/cryp - Fix PM reference leak...")
Fixes: 1cb3ad7019 ("crypto: stm32/hash - Fix PM reference leak...")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The CRYP IP checks the written key depending of the configuration, it's
safer to write the whole configuration to hardware then the key to avoid
unexpected key rejection.
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Extra crypto manager auto test were crashing or failling due
to 2 reasons:
- block in a dead loop (dues to issues in cipher end process management)
- crash due to read/write unmapped memory (this crash was also reported
when using openssl afalg engine)
Rework interrupt management, interrupts are masked as soon as they are
no more used: if input buffer is fully consumed, "Input FIFO not full"
interrupt is masked and if output buffer is full, "Output FIFO not
empty" interrupt is masked.
And crypto request finish when input *and* outpout buffer are fully
read/write.
About the crash due to unmapped memory, using scatterwalk_copychunks()
that will map and copy each block fix the issue.
Using this api and copying full block will also fix unaligned data
access, avoid early copy of in/out buffer, and make useless the extra
alignment constraint.
Fixes: 9e054ec21e ("crypto: stm32 - Support for STM32 CRYP crypto module")
Reported-by: Marek Vasut <marex@denx.de>
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This fixes the lrw autotest if lrw uses the CRYP as the AES block cipher
provider (as ecb(aes)). At end of request, CRYP should not update the IV
in case of ECB chaining mode. Indeed the ECB chaining mode never uses
the IV, but the software LRW chaining mode uses the IV field as
a counter and due to the (unexpected) update done by CRYP while the AES
block process, the counter get a wrong value when the IV overflow.
Fixes: 5f49f18d27 ("crypto: stm32/cryp - update to return iv_out")
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Some auto tests failed because driver wasn't returning the expected
error with some input size/iv value/tag size.
Now:
Return 0 early for empty buffer. (We don't need to start the engine for
an empty input buffer).
Accept any valid authsize for gcm(aes).
Return -EINVAL if iv for ccm(aes) is invalid.
Return -EINVAL if buffer size is a not a multiple of algorithm block size.
Fixes: 9e054ec21e ("crypto: stm32 - Support for STM32 CRYP crypto module")
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Don't erase key:
If key is erased before the crypto_finalize_.*_request() call, some
pending process will run with a key={ 0 }.
Moreover if the key is reset at end of request, it breaks xts chaining
mode, as for last xts block (in case input len is not a multiple of
block) a new AES request is started without calling again set_key().
Fixes: 9e054ec21e ("crypto: stm32 - Support for STM32 CRYP crypto module")
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
STM32 CRYP hardware doesn't manage CTR counter bigger than max U32, as
a workaround, at each block the current IV is saved, if the saved IV
lower u32 is 0xFFFFFFFF, the full IV is manually incremented, and set
in hardware.
Fixes: bbb2832620 ("crypto: stm32 - Fix sparse warnings")
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Change driver to not print an error message when the device
probe is deferred for a clock resource.
Signed-off-by: Etienne Carriere <etienne.carriere@foss.st.com>
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Change stm32 CRYP driver to defer its probe operation when
reset controller device is registered but has not been probed yet.
Signed-off-by: Etienne Carriere <etienne.carriere@foss.st.com>
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add an implementation of the ChaCha20 stream cipher (see e.g. RFC 7539)
that makes use of z13's vector instruction set extension.
The original implementation is by Andy Polyakov which is
adapted for kernel use.
Four to six blocks are processed in parallel resulting in a performance
gain for inputs >= 256 bytes.
chacha20-generic
1 operation in 622 cycles (256 bytes)
1 operation in 2346 cycles (1024 bytes)
chacha20-s390
1 operation in 218 cycles (256 bytes)
1 operation in 647 cycles (1024 bytes)
Cc: Andy Polyakov <appro@openssl.org>
Reviewed-by: Harald Freudenberger <freude@de.ibm.com>
Signed-off-by: Patrick Steuer <patrick.steuer@de.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
If kstrtoint() fails then "lfs_num" is uninitialized and the warning
doesn't make any sense. Just delete it.
Fixes: 8ec8015a31 ("crypto: octeontx2 - add support to process the crypto request")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use the FIELD_PREP() helper, instead of open-coding the same operation.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When caam queue is full (-ENOSPC), caam frees descriptor memory.
crypto-engine checks if retry support is true and h/w queue
is full(-ENOSPC), then requeue the crypto request.
During processing the requested descriptor again, caam gives below error.
(caam_jr 30902000.jr: 40000006: DECO: desc idx 0: Invalid KEY Command).
This patch adds a check to return when caam input ring is full
and retry support is true. so descriptor memory is not freed
and requeued request can be processed again.
Fixes: 2d653936eb ("crypto: caam - enable crypto-engine retry mechanism")
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Some optimize for the calculation of qos shaper parameters.
and modify the comments.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
1. Optimize overly long functions.
2. Fix the format symbol does not match the actual type.
3. Use the PCI_DEVFN to get the function id.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The value of qos should be reset after flr resetting or device
resetting. So set the max of qos value for every function. Then
update the value of qos when user writing the alg_qos.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The Allwinner D1 SoC has a crypto engine compatible with sun8i-ce.
Add support for it.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Improve and simplify logging of PFVF messages.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
PFVF debug messages use a mix of zero and one based VF IDs.
Switch to zero based VF numbers in all log messages.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Remove min_iov_compat_ver field as for now all versions are compatible.
Compatibility is determined by a series of rules and dynamic conditions
such as specific configurations.
In any case the minimum version requirement for compatibility is
an inadequate and obsolete approach which should be removed.
At this time compatibility can be assured across the currently available
versions.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Refactor version handling logic for ADF_VF2PF_MSGTYPE_COMPAT_VER_REQ
and ADF_VF2PF_MSGTYPE_VERSION_REQ on the PF.
Response messages are now filled only after fully parsing the request,
in a consisted way with the rest of the PFVF codebase.
This patch also fixes a harmless double setting for VERSION in the
response for ADF_VF2PF_MSGTYPE_VERSION_REQ.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Currently, any PF response to a VF request is fully parsed during the
interrupt handling. This way the individual response values are stored
into the accel_dev structure, preventing the caller to access and decode
the full response message itself.
Change this behavior, by letting the API return back the entire message
to the caller, in order to:
- keep correlated code together, that is, the (building of the)
request and the (decoding of the) response;
- avoid polluting the accel_dev data structure with unnecessary and at
times temporary values; only the entire message is stored in a
temporary buffer.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Replace PFVF constants with enumerations for valid protocol codes.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Organize PFVF protocol definitions by type rather than direction, by
keeping related fields close.
Also, make sure the order is consistent for both PF and VF definitions.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reorganize the structure of the PFVF code by moving the content of
adf_pf2vf_msg.c and adf_vf2pf_msg.c.
The logic that handles high level messages has been moved to
adf_pfvf_pf_msg.c and adf_pfvf_vf_msg.c.
The implementation of low level communication primitives and the
protocol is now included in adf_pfvf_pf_proto.c and adf_pfvf_vf_proto.c.
In addition, the file adf_pf2vf_msg.h has been renamed in adf_pfvf_msg.h
since it common to PF and VF and the copyright date for the touched
files has been updated.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Refactor the PFVF receive logic so it is common between PF and VF and
make it device specific.
This is in preparation for the introduction of PFVF support in the
qat_4xxx driver since the receive logic differs between QAT GEN2 and
QAT GEN4 devices.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Co-developed-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Make the PFVF send function device specific.
This is in preparation for the introduction of PFVF support in the
qat_4xxx driver since the send logic differs between QAT GEN2 and
QAT GEN4 devices.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add the function get_vf2pf_offset() to adf_pfvf_ops to differentiate the
CSRs used for pf2vf and vf2pf.
Offsets may or may not be direction specific depending on QAT
generation. Since in QAT GEN2 the CSR is not direction specific, i.e.
there is a single mailbox register shared for pf2vf and vf2pf, both
get_vf2pf_offset() and get_vf2pf_offset() will return the same offset.
This change is to make the direction explicit, so it is easier to
understand and debug and also in preparation for the introduction of
PFVF support in the qat_4xxx driver since QAT GEN4 devices have a
separate CSR for pf2vf and vf2pf communications.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add pfvf_ops structure to isolate PFVF related functions inside the
adf_hw_device_data structure.
For GEN2, the structure is populated using one of the two helper
functions, adf_gen2_init_pf_pfvf_ops() or adf_gen2_init_vf_pfvf_ops(),
for the PF and VF driver respectively.
For the DH895XCC PF driver, the structure is populated using
adf_gen2_init_pf_pfvf_ops() but some of the functions are then
overwritten.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move the function pfvf_comms_disabled() from the qat_4xxx module to
intel_qat as it will be used by other components to keep the PFVF
feature disabled.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move device specific PFVF logic related to the VF to the newly created
adf_gen2_pfvf.c.
This refactory is done to isolate the GEN2 PFVF code into its own file
in preparation for the introduction of support for PFVF for GEN4
devices.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move device specific PFVF logic related to the PF to the newly created
adf_gen2_pfvf.c.
This refactory is done to isolate the GEN2 PFVF code into its own file
in preparation for the introduction of support for PFVF for GEN4
devices.
In addition the PFVF PF logic for dh895xcc has been isolated to
adf_dh895xcc_hw_data.c.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Rework __adf_iov_putmsg() to handle retries due to collisions
internally, removing the need for an external retry loop.
The functions __adf_iov_putmsg() and adf_iov_putmsg() have been merged
together maintaining the adf_iov_putmsg() name.
This will allow to use this function only for GEN2 devices, since
collision are peculiar of this generation and therefore should be
confined to the actual implementation of the transport/medium access.
Note that now adf_iov_putmsg() will retry to send a message only in case
of collisions and will now fail if an ACK is not received from the
remote function.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Refactor the receive and handle logic to separate the parsing and
handling of the PFVF message from the initial retrieval and ACK.
This is to allow the intoduction of the recv function in a subsequent
patch.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If a PFVF message with MSGORIGIN_SYSTEM not set is received, re-enable
interrupts allowing the processing of new messages.
This is to simplify the refactoring of the recv function in a subsequent
patch.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Change the PFVF receipt flow on the VF side to read, ack and handle the
message instead of read, handle and ack.
This is done for (1) consistency with the PF side, see the function
adf_recv_and_handle_vf2pf_msg() in adf_pf2vf_msg.c, and (2) performance
reasons, to avoid keeping the CSR busy while parsing the message.
In addition, do not ACK PFVF legacy messages, as this driver is not
capable of handling PFVF legacy messages.
If a PFVF message with MSGORIGIN not set is received, do nothing.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move the interrupt handling call from the PF specific protocol file,
adf_pf2vf_msg.c, to adf_sriov.c to maintain the PFVF files focused on
the protocol handling.
The function adf_vf2pf_req_hndl() has been renamed as
adf_recv_and_handle_vf2pf_msg() to reflect its actual purpose and
maintain consistency with the VF side. This function now returns a
boolean indicating to the caller if interrupts need to be re-enabled or
not.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move the reading and parsing of a PF2VF message from the bottom half
function in adf_vf_isr.c, adf_pf2vf_bh_handler(), to the PFVF protocol
file adf_vf2pf_msg.c, for better code organization.
The receive and handle logic has been moved to a new function called
adf_recv_and_handle_pf2vf_msg() which returns a boolean indicating if
interrupts need to be re-enabled or not.
A slight refactoring has been done to avoid calculating the PF2VF CSR
offset twice and repeating the clearing of the PF2VFINT bit.
The "PF restarting" logic, now defined in the function
adf_pf2vf_handle_pf_restaring(), has been kept in adf_vf_isr.c due to
the dependencies with the adf_vf_stop_wq workqueue.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move vf2pf interrupt enable and disable functions from adf_pf2vf_msg.c
to adf_isr.c
This it to separate the interrupt related code from the PFVF protocol
logic.
With this change, the function adf_disable_vf2pf_interrupts_irq() is
only called from adf_isr.c and it has been marked as static.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move logic associated to handling VF2PF interrupt to its own function.
This will simplify the handling of multiple interrupt sources in the
function adf_msix_isr_ae() in the future.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If the remote function did not ACK the reception of a message, the
function __adf_iov_putmsg() could detect it as a collision.
This was due to the fact that the collision and the timeout checks after
the ACK loop were in the wrong order. The timeout must be checked at the
end of the loop, so fix by swapping the order of the two checks.
Fixes: 9b768e8a39 ("crypto: qat - detect PFVF collision after ACK")
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Co-developed-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The QAT driver does not have support for PFVF interrupts for GEN4
devices, therefore report the vf2pf sources as 0.
This prevents a NULL pointer dereference in the function
adf_msix_isr_ae() if the device triggers a spurious interrupt.
Fixes: 993161d36a ("crypto: qat - fix handling of VF to PF interrupts")
Reported-by: Adam Guerin <adam.guerin@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Static variables do not need to be initialized to 0.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
'destroy_workqueue()' already drains the queue before destroying it, so
there is no need to flush it explicitly.
Remove the redundant 'flush_workqueue()' calls.
This was generated with coccinelle:
@@
expression E;
@@
- flush_workqueue(E);
destroy_workqueue(E);
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Acked-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fix the following coccicheck REVIEW:
./drivers/crypto/marvell/octeontx2/otx2_cptvf_algs.c:1688:16-17 use swap() to make code cleaner
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: chiminghao <chi.minghao@zte.com.cn>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pointer alg points to sub field of tmpl, it
is dereferenced after tmpl is freed. Fix
this by accessing alg before free tmpl.
Fixes: ec8f5d8f ("crypto: qce - Qualcomm crypto engine driver")
Signed-off-by: Chengfeng Ye <cyeaa@connect.ust.hk>
Acked-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pointer base points to sub field of tmpl, it
is dereferenced after tmpl is freed. Fix
this by accessing base before free tmpl.
Fixes: ec8f5d8f ("crypto: qce - Qualcomm crypto engine driver")
Signed-off-by: Chengfeng Ye <cyeaa@connect.ust.hk>
Acked-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pointer alg points to sub field of tmpl, it
is dereferenced after tmpl is freed. Fix
this by accessing alg before free tmpl.
Fixes: 9363efb4 ("crypto: qce - Add support for AEAD algorithms")
Signed-off-by: Chengfeng Ye <cyeaa@connect.ust.hk>
Acked-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use the macro 'swap()' defined in 'include/linux/minmax.h' to avoid
opencoding it.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Yang Guang <yang.guang5@zte.com.cn>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fix to return negative error code -ENOMEM from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: c9f608c380 ("crypto: keembay-ocs-ecc - Add Keem Bay OCS ECC Driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When enable the kernel debug config, there is below calltrace detected:
BUG: using smp_processor_id() in preemptible [00000000] code: cryptomgr_test/339
caller is debug_smp_processor_id+0x20/0x30
CPU: 9 PID: 339 Comm: cryptomgr_test Not tainted 5.10.63-yocto-standard #1
Hardware name: NXP Layerscape LX2160ARDB (DT)
Call trace:
dump_backtrace+0x0/0x1a0
show_stack+0x24/0x30
dump_stack+0xf0/0x13c
check_preemption_disabled+0x100/0x110
debug_smp_processor_id+0x20/0x30
dpaa2_caam_enqueue+0x10c/0x25c
......
cryptomgr_test+0x38/0x60
kthread+0x158/0x164
ret_from_fork+0x10/0x38
According to the comment in commit ac5d15b4519f("crypto: caam/qi2
- use affine DPIOs "), because preemption is no longer disabled
while trying to enqueue an FQID, it might be possible to run the
enqueue on a different CPU(due to migration, when in process context),
however this wouldn't be a functionality issue. But there will be
above calltrace when enable kernel debug config. So, replace this_cpu_ptr
with raw_cpu_ptr to avoid above call trace.
Fixes: ac5d15b451 ("crypto: caam/qi2 - use affine DPIOs")
Cc: stable@vger.kernel.org
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In case there were more requests from different tfms in the crypto
queue, only the context of the last initialized tfm was considered.
Fixes: ec2088b66f ("crypto: atmel-aes - Allocate aes dev at tfm init time")
Reported-by: Wolfgang Ocker <weo@reccoware.de>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
-----BEGIN PGP SIGNATURE-----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=nsMh
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Conserve IRQs by setting up portdrv IRQs only when there are users
(Jan Kiszka)
- Rework and simplify _OSC negotiation for control of PCIe features
(Joerg Roedel)
- Remove struct pci_dev.driver pointer since it's redundant with the
struct device.driver pointer (Uwe Kleine-König)
Resource management:
- Coalesce contiguous host bridge apertures from _CRS to accommodate
BARs that cover more than one aperture (Kai-Heng Feng)
Sysfs:
- Check CAP_SYS_ADMIN before parsing user input (Krzysztof
Wilczyński)
- Return -EINVAL consistently from "store" functions (Krzysztof
Wilczyński)
- Use sysfs_emit() in endpoint "show" functions to avoid buffer
overruns (Kunihiko Hayashi)
PCIe native device hotplug:
- Ignore Link Down/Up caused by resets during error recovery so
endpoint drivers can remain bound to the device (Lukas Wunner)
Virtualization:
- Avoid bus resets on Atheros QCA6174, where they hang the device
(Ingmar Klein)
- Work around Pericom PI7C9X2G switch packet drop erratum by using
store and forward mode instead of cut-through (Nathan Rossi)
- Avoid trying to enable AtomicOps on VFs; the PF setting applies to
all VFs (Selvin Xavier)
MSI:
- Document that /sys/bus/pci/devices/.../irq contains the legacy INTx
interrupt or the IRQ of the first MSI (not MSI-X) vector (Barry
Song)
VPD:
- Add pci_read_vpd_any() and pci_write_vpd_any() to access anywhere
in the possible VPD space; use these to simplify the cxgb3 driver
(Heiner Kallweit)
Peer-to-peer DMA:
- Add (not subtract) the bus offset when calculating DMA address
(Wang Lu)
ASPM:
- Re-enable LTR at Downstream Ports so they don't report Unsupported
Requests when reset or hot-added devices send LTR messages
(Mingchuang Qiao)
Apple PCIe controller driver:
- Add driver for Apple M1 PCIe controller (Alyssa Rosenzweig, Marc
Zyngier)
Cadence PCIe controller driver:
- Return success when probe succeeds instead of falling into error
path (Li Chen)
HiSilicon Kirin PCIe controller driver:
- Reorganize PHY logic and add support for external PHY drivers
(Mauro Carvalho Chehab)
- Support PERST# GPIOs for HiKey970 external PEX 8606 bridge (Mauro
Carvalho Chehab)
- Add Kirin 970 support (Mauro Carvalho Chehab)
- Make driver removable (Mauro Carvalho Chehab)
Intel VMD host bridge driver:
- If IOMMU supports interrupt remapping, leave VMD MSI-X remapping
enabled (Adrian Huang)
- Number each controller so we can tell them apart in
/proc/interrupts (Chunguang Xu)
- Avoid building on UML because VMD depends on x86 bare metal APIs
(Johannes Berg)
Marvell Aardvark PCIe controller driver:
- Define macros for PCI_EXP_DEVCTL_PAYLOAD_* (Pali Rohár)
- Set Max Payload Size to 512 bytes per Marvell spec (Pali Rohár)
- Downgrade PIO Response Status messages to debug level (Marek Behún)
- Preserve CRS SV (Config Request Retry Software Visibility) bit in
emulated Root Control register (Pali Rohár)
- Fix issue in configuring reference clock (Pali Rohár)
- Don't clear status bits for masked interrupts (Pali Rohár)
- Don't mask unused interrupts (Pali Rohár)
- Avoid code repetition in advk_pcie_rd_conf() (Marek Behún)
- Retry config accesses on CRS response (Pali Rohár)
- Simplify emulated Root Capabilities initialization (Pali Rohár)
- Fix several link training issues (Pali Rohár)
- Fix link-up checking via LTSSM (Pali Rohár)
- Fix reporting of Data Link Layer Link Active (Pali Rohár)
- Fix emulation of W1C bits (Marek Behún)
- Fix MSI domain .alloc() method to return zero on success (Marek
Behún)
- Read entire 16-bit MSI vector in MSI handler, not just low 8 bits
(Marek Behún)
- Clear Root Port I/O Space, Memory Space, and Bus Master Enable bits
at startup; PCI core will set those as necessary (Pali Rohár)
- When operating as a Root Port, set class code to "PCI Bridge"
instead of the default "Mass Storage Controller" (Pali Rohár)
- Add emulation for PCI_BRIDGE_CTL_BUS_RESET since aardvark doesn't
implement this per spec (Pali Rohár)
- Add emulation of option ROM BAR since aardvark doesn't implement
this per spec (Pali Rohár)
MediaTek MT7621 PCIe controller driver:
- Add MediaTek MT7621 PCIe host controller driver and DT binding
(Sergio Paracuellos)
Qualcomm PCIe controller driver:
- Add SC8180x compatible string (Bjorn Andersson)
- Add endpoint controller driver and DT binding (Manivannan
Sadhasivam)
- Restructure to use of_device_get_match_data() (Prasad Malisetty)
- Add SC7280-specific pcie_1_pipe_clk_src handling (Prasad Malisetty)
Renesas R-Car PCIe controller driver:
- Remove unnecessary includes (Geert Uytterhoeven)
Rockchip DesignWare PCIe controller driver:
- Add DT binding (Simon Xue)
Socionext UniPhier Pro5 controller driver:
- Serialize INTx masking/unmasking (Kunihiko Hayashi)
Synopsys DesignWare PCIe controller driver:
- Run dwc .host_init() method before registering MSI interrupt
handler so we can deal with pending interrupts left by bootloader
(Bjorn Andersson)
- Clean up Kconfig dependencies (Andy Shevchenko)
- Export symbols to allow more modular drivers (Luca Ceresoli)
TI DRA7xx PCIe controller driver:
- Allow host and endpoint drivers to be modules (Luca Ceresoli)
- Enable external clock if present (Luca Ceresoli)
TI J721E PCIe driver:
- Disable PHY when probe fails after initializing it (Christophe
JAILLET)
MicroSemi Switchtec management driver:
- Return error to application when command execution fails because an
out-of-band reset has cleared the device BARs, Memory Space Enable,
etc (Kelvin Cao)
- Fix MRPC error status handling issue (Kelvin Cao)
- Mask out other bits when reading of management VEP instance ID
(Kelvin Cao)
- Return EOPNOTSUPP instead of ENOTSUPP from sysfs show functions
(Kelvin Cao)
- Add check of event support (Logan Gunthorpe)
Miscellaneous:
- Remove unused pci_pool wrappers, which have been replaced by
dma_pool (Cai Huoqing)
- Use 'unsigned int' instead of bare 'unsigned' (Krzysztof
Wilczyński)
- Use kstrtobool() directly, sans strtobool() wrapper (Krzysztof
Wilczyński)
- Fix some sscanf(), sprintf() format mismatches (Krzysztof
Wilczyński)
- Update PCI subsystem information in MAINTAINERS (Krzysztof
Wilczyński)
- Correct some misspellings (Krzysztof Wilczyński)"
* tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (137 commits)
PCI: Add ACS quirk for Pericom PI7C9X2G switches
PCI: apple: Configure RID to SID mapper on device addition
iommu/dart: Exclude MSI doorbell from PCIe device IOVA range
PCI: apple: Implement MSI support
PCI: apple: Add INTx and per-port interrupt support
PCI: kirin: Allow removing the driver
PCI: kirin: De-init the dwc driver
PCI: kirin: Disable clkreq during poweroff sequence
PCI: kirin: Move the power-off code to a common routine
PCI: kirin: Add power_off support for Kirin 960 PHY
PCI: kirin: Allow building it as a module
PCI: kirin: Add MODULE_* macros
PCI: kirin: Add Kirin 970 compatible
PCI: kirin: Support PERST# GPIOs for HiKey970 external PEX 8606 bridge
PCI: apple: Set up reference clocks when probing
PCI: apple: Add initial hardware bring-up
PCI: of: Allow matching of an interrupt-map local to a PCI device
of/irq: Allow matching of an interrupt-map local to an interrupt controller
irqdomain: Make of_phandle_args_to_fwspec() generally available
PCI: Do not enable AtomicOps on VFs
...
Pull crypto updates from Herbert Xu:
"API:
- Delay boot-up self-test for built-in algorithms
Algorithms:
- Remove fallback path on arm64 as SIMD now runs with softirq off
Drivers:
- Add Keem Bay OCS ECC Driver"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (61 commits)
crypto: testmgr - fix wrong key length for pkcs1pad
crypto: pcrypt - Delay write to padata->info
crypto: ccp - Make use of the helper macro kthread_run()
crypto: sa2ul - Use the defined variable to clean code
crypto: s5p-sss - Add error handling in s5p_aes_probe()
crypto: keembay-ocs-ecc - Add Keem Bay OCS ECC Driver
dt-bindings: crypto: Add Keem Bay ECC bindings
crypto: ecc - Export additional helper functions
crypto: ecc - Move ecc.h to include/crypto/internal
crypto: engine - Add KPP Support to Crypto Engine
crypto: api - Do not create test larvals if manager is disabled
crypto: tcrypt - fix skcipher multi-buffer tests for 1420B blocks
hwrng: s390 - replace snprintf in show functions with sysfs_emit
crypto: octeontx2 - set assoclen in aead_do_fallback()
crypto: ccp - Fix whitespace in sev_cmd_buffer_len()
hwrng: mtk - Force runtime pm ops for sleep ops
crypto: testmgr - Only disable migration in crypto_disable_simd_for_test()
crypto: qat - share adf_enable_pf2vf_comms() from adf_pf2vf_msg.c
crypto: qat - extract send and wait from adf_vf2pf_request_version()
crypto: qat - add VF and PF wrappers to common send function
...
The end goal of the current buffer overflow detection work[0] is to gain
full compile-time and run-time coverage of all detectable buffer overflows
seen via array indexing or memcpy(), memmove(), and memset(). The str*()
family of functions already have full coverage.
While much of the work for these changes have been on-going for many
releases (i.e. 0-element and 1-element array replacements, as well as
avoiding false positives and fixing discovered overflows[1]), this series
contains the foundational elements of several related buffer overflow
detection improvements by providing new common helpers and FORTIFY_SOURCE
changes needed to gain the introspection required for compiler visibility
into array sizes. Also included are a handful of already Acked instances
using the helpers (or related clean-ups), with many more waiting at the
ready to be taken via subsystem-specific trees[2]. The new helpers are:
- struct_group() for gaining struct member range introspection.
- memset_after() and memset_startat() for clearing to the end of structures.
- DECLARE_FLEX_ARRAY() for using flex arrays in unions or alone in structs.
Also included is the beginning of the refactoring of FORTIFY_SOURCE to
support memcpy() introspection, fix missing and regressed coverage under
GCC, and to prepare to fix the currently broken Clang support. Finishing
this work is part of the larger series[0], but depends on all the false
positives and buffer overflow bug fixes to have landed already and those
that depend on this series to land.
As part of the FORTIFY_SOURCE refactoring, a set of both a compile-time
and run-time tests are added for FORTIFY_SOURCE and the mem*()-family
functions respectively. The compile time tests have found a legitimate
(though corner-case) bug[6] already.
Please note that the appearance of "panic" and "BUG" in the
FORTIFY_SOURCE refactoring are the result of relocating existing code,
and no new use of those code-paths are expected nor desired.
Finally, there are two tree-wide conversions for 0-element arrays and
flexible array unions to gain sane compiler introspection coverage that
result in no known object code differences.
After this series (and the changes that have now landed via netdev
and usb), we are very close to finally being able to build with
-Warray-bounds and -Wzero-length-bounds. However, due corner cases in
GCC[3] and Clang[4], I have not included the last two patches that turn
on these options, as I don't want to introduce any known warnings to
the build. Hopefully these can be solved soon.
[0] https://lore.kernel.org/lkml/20210818060533.3569517-1-keescook@chromium.org/
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/log/?qt=grep&q=FORTIFY_SOURCE
[2] https://lore.kernel.org/lkml/202108220107.3E26FE6C9C@keescook/
[3] https://lore.kernel.org/lkml/3ab153ec-2798-da4c-f7b1-81b0ac8b0c5b@roeck-us.net/
[4] https://bugs.llvm.org/show_bug.cgi?id=51682
[5] https://lore.kernel.org/lkml/202109051257.29B29745C0@keescook/
[6] https://lore.kernel.org/lkml/20211020200039.170424-1-keescook@chromium.org/
-----BEGIN PGP SIGNATURE-----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=9xbT
-----END PGP SIGNATURE-----
Merge tag 'overflow-v5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull overflow updates from Kees Cook:
"The end goal of the current buffer overflow detection work[0] is to
gain full compile-time and run-time coverage of all detectable buffer
overflows seen via array indexing or memcpy(), memmove(), and
memset(). The str*() family of functions already have full coverage.
While much of the work for these changes have been on-going for many
releases (i.e. 0-element and 1-element array replacements, as well as
avoiding false positives and fixing discovered overflows[1]), this
series contains the foundational elements of several related buffer
overflow detection improvements by providing new common helpers and
FORTIFY_SOURCE changes needed to gain the introspection required for
compiler visibility into array sizes. Also included are a handful of
already Acked instances using the helpers (or related clean-ups), with
many more waiting at the ready to be taken via subsystem-specific
trees[2].
The new helpers are:
- struct_group() for gaining struct member range introspection
- memset_after() and memset_startat() for clearing to the end of
structures
- DECLARE_FLEX_ARRAY() for using flex arrays in unions or alone in
structs
Also included is the beginning of the refactoring of FORTIFY_SOURCE to
support memcpy() introspection, fix missing and regressed coverage
under GCC, and to prepare to fix the currently broken Clang support.
Finishing this work is part of the larger series[0], but depends on
all the false positives and buffer overflow bug fixes to have landed
already and those that depend on this series to land.
As part of the FORTIFY_SOURCE refactoring, a set of both a
compile-time and run-time tests are added for FORTIFY_SOURCE and the
mem*()-family functions respectively. The compile time tests have
found a legitimate (though corner-case) bug[6] already.
Please note that the appearance of "panic" and "BUG" in the
FORTIFY_SOURCE refactoring are the result of relocating existing code,
and no new use of those code-paths are expected nor desired.
Finally, there are two tree-wide conversions for 0-element arrays and
flexible array unions to gain sane compiler introspection coverage
that result in no known object code differences.
After this series (and the changes that have now landed via netdev and
usb), we are very close to finally being able to build with
-Warray-bounds and -Wzero-length-bounds.
However, due corner cases in GCC[3] and Clang[4], I have not included
the last two patches that turn on these options, as I don't want to
introduce any known warnings to the build. Hopefully these can be
solved soon"
Link: https://lore.kernel.org/lkml/20210818060533.3569517-1-keescook@chromium.org/ [0]
Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/log/?qt=grep&q=FORTIFY_SOURCE [1]
Link: https://lore.kernel.org/lkml/202108220107.3E26FE6C9C@keescook/ [2]
Link: https://lore.kernel.org/lkml/3ab153ec-2798-da4c-f7b1-81b0ac8b0c5b@roeck-us.net/ [3]
Link: https://bugs.llvm.org/show_bug.cgi?id=51682 [4]
Link: https://lore.kernel.org/lkml/202109051257.29B29745C0@keescook/ [5]
Link: https://lore.kernel.org/lkml/20211020200039.170424-1-keescook@chromium.org/ [6]
* tag 'overflow-v5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (30 commits)
fortify: strlen: Avoid shadowing previous locals
compiler-gcc.h: Define __SANITIZE_ADDRESS__ under hwaddress sanitizer
treewide: Replace 0-element memcpy() destinations with flexible arrays
treewide: Replace open-coded flex arrays in unions
stddef: Introduce DECLARE_FLEX_ARRAY() helper
btrfs: Use memset_startat() to clear end of struct
string.h: Introduce memset_startat() for wiping trailing members and padding
xfrm: Use memset_after() to clear padding
string.h: Introduce memset_after() for wiping trailing members/padding
lib: Introduce CONFIG_MEMCPY_KUNIT_TEST
fortify: Add compile-time FORTIFY_SOURCE tests
fortify: Allow strlen() and strnlen() to pass compile-time known lengths
fortify: Prepare to improve strnlen() and strlen() warnings
fortify: Fix dropped strcpy() compile-time write overflow check
fortify: Explicitly disable Clang support
fortify: Move remaining fortify helpers into fortify-string.h
lib/string: Move helper functions out of string.c
compiler_types.h: Remove __compiletime_object_size()
cm4000_cs: Use struct_group() to zero struct cm4000_dev region
can: flexcan: Use struct_group() to zero struct flexcan_regs regions
...
Repalce kthread_create/wake_up_process() with kthread_run()
to simplify the code.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use the defined variable "dev" to make the code cleaner.
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The function s5p_aes_probe() does not perform sufficient error
checking after executing platform_get_resource(), thus fix it.
Fixes: c2afad6c61 ("crypto: s5p-sss - Add HASH support for Exynos")
Cc: <stable@vger.kernel.org>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The Intel Keem Bay SoC can provide hardware acceleration of Elliptic
Curve Cryptography (ECC) by means of its Offload and Crypto Subsystem
(OCS).
Add the Keem Bay OCS ECC driver which leverages such hardware
capabilities to provide hardware-acceleration of ECDH-256 and ECDH-384.
Signed-off-by: Prabhjot Khurana <prabhjot.khurana@intel.com>
Co-developed-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Signed-off-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Currently, in case of aead fallback, no associated data info is set in the
fallback request. To fix this, call aead_request_set_ad() to pass the assoclen.
Fixes: 6f03f0e8b6 ("crypto: octeontx2 - register with linux crypto framework")
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Extra tab in sev_cmd_buffer_len().
Signed-off-by: Peter Gonda <pgonda@google.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Marc Orr <marcorr@google.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Rientjes <rientjes@google.com>
Cc: John Allen <john.allen@amd.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-crypto@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Marc Orr <marcorr@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Replace dev->driver_name() by dev_driver_string() for the corresponding
struct device. This is a step toward removing pci_dev->driver.
[bhelgaas: split to separate patch]
Link: https://lore.kernel.org/r/20211004125935.2300113-8-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
A struct pci_driver is shared across all device instances, so assigning
pci_driver.err_handler once per device isn't really sensible.
Set adf_driver.err_handler statically instead of in adf_enable_aer().
This removes a use of pci_dev->driver, which is a step toward removing
pci_dev->driver altogether.
Since adf_enable_aer() returns zero unconditionally, make it a void
function.
Link: https://lore.kernel.org/r/20211004125935.2300113-10-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PFVF protocol "enable" functions are direction specific but not
device specific. Move the protocol enable function for the PF into the
PF specific protocol file for better file organization and duplicated
code reduction.
NOTE: the patch keeps gen4 disabled as it doesn't have full PFVF
support yet.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In the function adf_vf2pf_request_version(), the VF sends a request to
the PF and waits for a response before parsing and handling it.
Since this pattern will be used by other requests, define a new
function, adf_send_vf2pf_req(), that only deals with sending a VF2PF
request and waiting for a response.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The send function, adf_iov_putmsg(), is shared by both PF and VF.
This commit provides two direction specific APIs, adf_send_pf2vf_msg()
and adf_send_vf2pf_msg() which decouple the implementation, which can
change and evolve over time, from the user.
With this change, the adf_iov_putmsg() is now isolated inside the file
adf_pf2vf_msg.c and has been marked as static.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Replace any reference of "IOV" with PFVF in the collision constants.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Keep adf_pf2vf_msg.h as much as possible focused on the protocol
definition.
Instead, collision parameters are an implementation detail which should
stay close to the code consuming them, therefore move them to
adf_pf2vf_msg.c.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The functions adf_iov_putmsg() and __adf_iov_putmsg() are shared by both
PF and VF. Any logging or documentation should not refer to any specific
direction.
Make comments and log messages direction agnostic by replacing PF2VF
with PFVF. Also fix the wording for some related comments.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Replace homegrown bit counting logic in adf_gen2_get_num_accels() and
adf_gen2_get_num_aes() with the functions hweight16() and hweight32(),
respectively.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
QAT GEN2 devices share most of the behavior which means a number of
device specific functions can be shared too and some differences
abstracted away by simple parameters.
The functions adf_enable_error_correction(), get_num_accels(),
get_num_aes() and get_pf2vf_offset() for c3xxx, c62x and dh895xx have
been reworked and moved to the GEN2 file, adf_gen2_hw_data.c.
The definitions of tx_rx_gap and tx_rings_mask have been moved to
adf_gen2_hw_data.h.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Currently, VF to PF interrupt handling is based on the DH895XCC device
behavior, which is not entirely common to all devices.
In order to make interrupt detection and handling correct for all of the
supported devices, make the interrupt handling device specific by:
- introducing get_vf2pf_sources() for getting a 32 bits long value
where each bit represents a vf2pf interrupt;
- adding the device [enable|disable]_vf2pf_interrupts to hw_data;
- defining [enable|disable]_vf2pf_interrupts for all the devices that
are currently supported, using only their required and specific
ERRSOU|ERRMASK registers (DH895XCC has 32 interrupts spread across
ERRSOU3 and ERRSOU5, C62X/C3XXX has 16 in ERRSOU3 only, etc).
Code has been shared by different devices wherever possible.
This patch is based on earlier work done by Salvatore Benedetto.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The initial version of the PFVF protocol included an initial "carrier
sensing" to get ownership of the channel.
Collisions can happen anyway, the extra wait and test does not prevent
collisions, it instead slows the communication down, so remove it.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Upon receiving a PFVF message, check if the interrupt bit is set in the
message. If it is not, that means that the interrupt was probably
triggered by a collision. In this case, disregard the message and
re-enable the interrupts.
Fixes: ed8ccaef52 ("crypto: qat - Add support for SRIOV")
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Detect a PFVF collision between the local and the remote function by
checking if the message on the PFVF CSR has been overwritten.
This is done after the remote function confirms that the message has
been received, by clearing the interrupt bit, or the maximum number of
attempts (ADF_IOV_MSG_ACK_MAX_RETRY) to check the CSR has been exceeded.
Fixes: ed8ccaef52 ("crypto: qat - Add support for SRIOV")
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Co-developed-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
clang points out inconsistencies in the FIELD_PREP() invocation in
this driver that result from the 'mask' being a 32-bit value:
drivers/crypto/ccree/cc_driver.c:117:18: error: result of comparison of constant 18446744073709551615 with expression of type 'u32' (aka 'unsigned int') is always false [-Werror,-Wtautological-constant-out-of-range-compare]
cache_params |= FIELD_PREP(mask, val);
^~~~~~~~~~~~~~~~~~~~~
include/linux/bitfield.h:94:3: note: expanded from macro 'FIELD_PREP'
__BF_FIELD_CHECK(_mask, 0ULL, _val, "FIELD_PREP: "); \
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
include/linux/bitfield.h:52:28: note: expanded from macro '__BF_FIELD_CHECK'
BUILD_BUG_ON_MSG((_mask) > (typeof(_reg))~0ull, \
~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
This does not happen in other places that just pass a constant here.
Work around the warnings by widening the type of the temporary variable.
Fixes: 05c2a70591 ("crypto: ccree - rework cache parameters handling")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Gilad ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
As qm should register to uacce in UACCE_DEV_SVA mode,
this patch modifies to checks uacce mode before doing uacce
registration.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There is a spelling mistake in a literal string. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The MODULE_DEVICE_TABLE already creates proper alias for platform
driver. Having another MODULE_ALIAS causes the alias to be duplicated.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
After reset or boot, QAT 4xxx devices are inactive and require to be
explicitly activated.
This is done by writing the DRV_ACTIVE bit in the PM_INTERRUPT register
and polling the PM_INIT_STATE to make sure that the transaction has
completed properly.
If this is not done, the driver will fail the initialization sequence
reporting the following message:
[ 22.081193] 4xxx 0000:f7:00.0: enabling device (0140 -> 0142)
[ 22.720285] QAT: AE0 is inactive!!
[ 22.720287] QAT: failed to get device out of reset
[ 22.720288] 4xxx 0000:f7:00.0: qat_hal_clr_reset error
[ 22.720290] 4xxx 0000:f7:00.0: Failed to init the AEs
[ 22.720290] 4xxx 0000:f7:00.0: Failed to initialise Acceleration Engine
[ 22.720789] 4xxx 0000:f7:00.0: Resetting device qat_dev0
[ 22.825099] 4xxx: probe of 0000:f7:00.0 failed with error -14
The patch also temporarily disables the power management source of
interrupt, to avoid possible spurious interrupts as the power management
feature is not fully supported.
The device init function has been added to adf_dev_init(), and not in the
probe of 4xxx to make sure that the device is re-enabled in case of
reset.
Note that the error code reported by hw_data->init_device() in
adf_dev_init() has been shadowed for consistency with the other calls
in the same function.
Fixes: 8c8268166e ("crypto: qat - add qat_4xxx driver")
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
On newer CAAM versions, not all accelerators are disabled if the SoC is
a non-E variant. While the driver checks most of the modules for
availability, there is one - PKHA - which sticks out. On non-E variants
it is still reported as available, that is the number of instances is
non-zero, but it has limited functionality. In particular it doesn't
support encryption and decryption, but just signing and verifying. This
is indicated by a bit in the PKHA_MISC field. Take this bit into account
if we are checking for availability.
This will the following error:
[ 8.167817] caam_jr 8020000.jr: 20000b0f: CCB: desc idx 11: : Invalid CHA selected.
Tested on an NXP LS1028A (non-E) SoC.
Fixes: d239b10d4c ("crypto: caam - add register map changes cf. Era 10")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There are three bugs in this code:
1) If we ccp_init_data() fails for &src then we need to free aad.
Use goto e_aad instead of goto e_ctx.
2) The label to free the &final_wa was named incorrectly as "e_tag" but
it should have been "e_final_wa". One error path leaked &final_wa.
3) The &tag was leaked on one error path. In that case, I added a free
before the goto because the resource was local to that block.
Fixes: 36cf515b9b ("crypto: ccp - Enable support for AES GCM on v5 CCPs")
Reported-by: "minihanshen(沈明航)" <minihanshen@tencent.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: John Allen <john.allen@amd.com>
Tested-by: John Allen <john.allen@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The assignment to error return variable ret and then the jump to
an error exit path can be simplified by just returning the error
return at the failure point. This allows variable ret and the
error return path to be removed. This cleans up a static analysis
warninng that variable ret is being assigned (value never being
used) and being re-assigned later.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Remove packed attribute from structures that do not need to be packed.
These are just used internally and not shared with firmware.
This also fixes a series of warning when compiling the driver with the
flag -Waddress-of-packed-member, similar to the following:
drivers/crypto/qat/qat_c62xvf/adf_c62xvf_hw_data.c:102:28: warning: taking address of packed member 'csr_ops' of class or structure 'adf_hw_device_data' may result in an unaligned pointer value
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If devm_request_irq() fails inside adf_request_irqs(), unwind properly by
freeing the allocated irqs.
Signed-off-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Change the irq allocation logic so that it is possible to free only the
allocated irqs in case of error.
A new flag is introduced for every PF/VF interrupt. This flag is set to
"true" only when the interrupt is requested.
During clean up, devm_free_irq() is only called if this flag is set.
Signed-off-by: Maksim Lukoshkov <maksim.lukoshkov@intel.com>
Co-developed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Signed-off-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch removes redundant CPU affinity to AE cluster IRQ.
Signed-off-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Allocate an extra memory page for qp in the qp memory initialization.
Set a qp error flag in the extra page addr when device resetting.
This error flag can be seen in the userspace. This flag can helps
users to stop tasks when device resetting. After resetting, this error
flag will be reset when this qp is created again. So app should release
the old qp and request a new one, and do the task on the new queue
again.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Allocate an extra memory page for qp. This extra page is
used to set the device or qp status. But this page not
be used currently. Meanwhile it leads to dus size not equal
to mmap size as using uacce sva mode, and cause the app task
broken.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The function qm_qos_value_init expects an unsigned integer but
is incorrectly supplying a signed format to sscanf. This patch
fixes it.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add a new CCP/PSP PCI device ID and corresponding entry in the dev_vdata
struct.
Signed-off-by: John Allen <john.allen@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
To support runtime PM, use the function 'pci_set_power_state' to change
the power state. Therefore, method _PS0 or _PR0 needs to be filled by
platform. So check whether the method is supported, if not, print a
prompt information.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
To avoid repeatedly obtaining 'qm' from 'filp', parameter passing of
debugfs function directly use 'qm' instead of 'filp'.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Accelerator devices support runtime PM to reduce power consumption.
This patch adds the runtime PM suspend/resume callbacks to the
accelerator devices.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The accelerator devices support runtime PM, when device is in suspended, an
exception will occur if reading registers. Therefore, this patch uses
'debugfs_create_file' instead of 'debugfs_create_regset32' to create
debugfs file, and then the driver can get the device status before
reading the register.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When the endian configuration of the hardware is abnormal, it will
cause the SEC engine is faulty that reports empty message. And it
will affect the normal function of the hardware. Currently the soft
configuration method can't restore the faulty device. The endian
needs to be configured according to the system properties. So fix it.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Because the algs registration process has added a judgment.
So need to add the judgment for the abnormal exiting process.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If the VF is newer than the PF, it decides whether it is compatible or
not. In case it is compatible, store that information in the
vf.compatible flag in the accel_dev structure.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Suggested-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The function adf_iov_putmsg() is only used inside the intel_qat module
therefore should not be exported.
Remove EXPORT_SYMBOL for the function adf_iov_putmsg().
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There is a race condition during shutdown in adf_disable_sriov() where
both the PF and the VF drivers are loaded on the host system.
The PF notifies a VF with a "RESTARTING" message due to which the VF
starts an asynchronous worker to stop and shutdown itself.
At the same time the PF calls pci_disable_sriov() which invokes the
remove() routine on the VF device driver triggering the shutdown flow
again.
This change fixes the problem by ensuring that the VF flushes the worker
that performs stop()/shutdown() before these two functions are called in
the remove(). To make sure that no additional PV/VF messages are
processed by the VF, interrupts are disabled before flushing the
workqueue.
Signed-off-by: Ahsan Atta <ahsan.atta@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
All QAT GEN2 devices share the same register offset for masking interrupts,
so they don't need any complex device specific infrastructure.
Remove this function in favor of a constant in order to simplify the code.
Also, future generations may require a more complex device specific
handling, making the current approach obsolete anyway.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Currently all the functions related to the activation of the PFVF
protocol, both on PF and VF, include the direction specific "vf2pf"
name.
Replace the existing naming schema with:
- a direction agnostic naming, that applies to both PF and VF, for the
function pointer ("pfvf")
- a direction specific naming schema for the implementations ("pf2vf" or
"vf2pf")
In particular this patch renames:
- adf_pf_enable_vf2pf_comms() in adf_enable_pf2vf_comms()
- enable_vf2pf_comms() in enable_pfvf_comms()
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Make sure all the steps in the initialization sequence are complete
before any completion event notification.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move IOV functions at the end of hw_data so that PFVF functions related
functions are group together.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
At start and shutdown, VFs notify the PF about their state. These
notifications are carried out through a message exchange using the PFVF
protocol.
Function names lead to believe they do perform init or shutdown logic.
This is to fix the naming to better reflect their purpose.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In the PF interrupt handler, the interrupt is disabled for a set of VFs
by writing to the interrupt source mask register, ERRMSK.
The interrupt is re-enabled in the bottom half handler by writing to the
same CSR. This is done through the functions enable_vf2pf_interrupts()
and disable_vf2pf_interrupts() which perform a read-modify-write
operation on the ERRMSK registers to mask and unmask the source of
interrupt.
There can be a race condition where the top half handler for one VF
interrupt runs just as the bottom half for another VF is about to
re-enable the interrupt. Depending on whether the top or bottom half
updates the CSR first, this would result either in a spurious interrupt
or in the interrupt not being re-enabled.
This patch protects the access of ERRMSK with a spinlock.
The functions adf_enable_vf2pf_interrupts() and
adf_disable_vf2pf_interrupts() have been changed to acquire a spin lock
before accessing and modifying the ERRMSK registers. These functions use
spin_lock_irqsave() to disable IRQs and avoid potential deadlocks.
In addition, the function adf_disable_vf2pf_interrupts_irq() has been
added. This uses spin_lock() and it is meant to be used in the top half
only.
Signed-off-by: Kanchana Velusamy <kanchanax.velusamy@intel.com>
Co-developed-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Interrupt code to enable interrupts from PF does not belong to the
protocol code, so move it to the interrupt handling specific file for
better code organization.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use reinit_completion() to set to a clean state a completion variable,
used to coordinate the VF to PF request-response flow, before every
new VF request.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The PF driver uses the tasklet vf2pf_bh_tasklet to schedule a workqueue
to handle the vf2vf protocol (pf2vf_resp_wq).
Since the tasklet is only used to schedule the workqueue, this patch
removes it and schedules the pf2vf_resp_wq workqueue directly for the
top half.
Signed-off-by: Svyatoslav Pankratov <svyatoslav.pankratov@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Rename ADF_PFVF_COMPATIBILITY_VERSION in ADF_PFVF_COMPAT_THIS_VERSION
since it is used to indicate the current version of the PFVF protocol.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Marco Chiappero
Giovanni Cabiddu
Jiapeng Chong
Corentin Labbe
Yang Shen
Weili Qian
Gustavo A. R. Silva
David Rientjes
Peter Gonda
Srujana Challa
Herbert Xu
Nicolas Toromanoff
Etienne Carriere
Patrick Steuer
Dan Carpenter
Geert Uytterhoeven
Gaurav Jain
Kai Ye
Corentin Labbe
Jason Wang
Christophe JAILLET
chiminghao
Chengfeng Ye
Yang Guang
Wei Yongjun
Meng Li
Tudor Ambarus
Linus Torvalds
Cai Huoqing
Tang Bin
Prabhjot Khurana
Kees Cook
Ovidiu Panait
Uwe Kleine-König
Arnd Bergmann
Colin Ian King
Krzysztof Kozlowski
Michael Walle
Wojciech Ziemba
Maksim Lukoshkov
John Allen
Ahsan Atta
Kanchana Velusamy
Svyatoslav Pankratov