This saves some power. OMAP4 version should check for GPT module ID, as
autoidle is only supported on a subset of these.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Create a new API that forms a wrapper to _set_module_autoidle()
to modify the AUTOIDLE bit.
This API is intended to be used by drivers that requires direct
manipulation of the AUTOIDLE bits in SYSCONFIG register.
McBSP driver requires autoidle bit to be enabled/disabled while
using sidetone feature.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: restrict the hwmod states that the autoidle bit can be changed
in; changed function name; dropped "int" from "unsigned int long"]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some boards can't tolerate IP blocks being reset when they are initialized.
Michael Büsch cites a case with the Nokia N810:
http://www.spinics.net/lists/linux-omap/msg47277.html
To allow such boards to continue working normally, allow board file
maintainers to mark IP blocks to prevent them from being reset upon
init. This is done via a hwmod function, omap_hwmod_no_setup_reset().
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Michael Buesch <mb@bu3sch.de>
On OMAP2 and OMAP3 the reset ctrl shift doesn't match the
status bit, as it does on OMAP4, when handling the reset lines.
This patch adds a new member in the reset info structure, so now it
can be added as part of hwmod data, and checked accordingly for
OMAP2 or 3; otherwise, there could be cases when the shift masks
doesn't match both of the registers, and a successful reset might
throw an error message or vice versa.
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
[paul@pwsan.com: added a warning if st_shift used on OMAP4; renamed 'r'
variable; improved some documentation]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Now that omap_hwmod + omap_device is used for OMAP UART device and
driver code, we no longer need the UART physical addresses in
omap_globals.
Note that the #defines for the base addresses are still left in
<plat/serial.h> since they are used by DEBUG_LL and uncompress code.
Build tested for OMAP1 (omap1_defconfig) and OMAP2+ (omap2plus_defconfig)
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add the address spaces, irqs of the l3 interconnect to the
hwmod data. The hwmod changes are aligned with Benoit Cousson.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Remove the DPLL rate tolerance code that is called during rate
rounding. As far as I know, this code is never used, since it's been
more important for callers of the DPLL round_rate()/set_rate()
functions to obtain an exact rate than it is to save a relatively
small amount of power.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Bail out before we take the clockfw_lock spinlock if the corresponding
OMAP1 or OMAP2+ clock function is not defined. The intention is to
reduce and simplify the work that is done inside the spinlock.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
At this point in time, there's no reason for this header file to be in
plat-omap/include/plat/voltage.h. It should not be included by device
drivers, and the code that uses it is currently all under mach-omap2/.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
There's no reason for this header file to be in
plat-omap/include/plat/smartreflex.h. The hardware devices are in
OMAP2+ SoCs only. Leaving this header file in plat-omap causes
problems due to cross-dependencies with other header files that should
live in mach-omap2/.
Thanks to Benoît Cousson <b-cousson@ti.com> for suggesting the removal
of the smartreflex.h include from the OMAP3xxx hwmod data.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
WARNING: arch/arm/plat-omap/built-in.o(.data+0x6d4): Section mismatch in reference from the variable omap_driver to the function .init.text:omap_cpu_init()
The variable omap_driver references
the function __init omap_cpu_init()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The _add_optional_clock_alias function expects an entry
already existing in the clkdev table in the form of
<dev-id=NULL, con-id=role> which might not be the case
always.
Instead, just check if an entry already exists in clkdev
in the <dev-id=dev_name, con-id=role> form, else go ahead
and add one.
Remove any assumption of an entry already existing in clkdev
table in any form.
Since this means, adding a new entry in clkdev if it does
not already exist, and not really adding an 'alias',
also rename the function name
(s/_add_optional_clock_alias/_add_optional_clock_clkdev)
to reflect this.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Reported-by: Sumit Semwal <sumit.semwal@ti.com>
Cc: Sumit Semwal <sumit.semwal@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Partha Basak <p-basak2@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP2420 platform consists of mmc block as in omap1 and not the
hsmmc block as present in omap2430, omap3, omap4 platforms.
Removing all base address macro defines except keeping one for OMAP2420 and
adapting only hsmmc device registration and driver to hwmod framework.
Changes involves:
1) Remove controller reset in devices.c which is taken care of
by hwmod framework.
2) Using omap-device layer to register device and utilizing data from
hwmod data file for base address, dma channel number, Irq_number,
device attribute.
3) Update the driver to use dev_attr to find whether controller
supports dual volt cards
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Reviewed-by: Balaji T K <balajitk@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
CC: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a device attribute to hwmod data of omap2430, omap3, omap4.
Currently the device attribute holds information regarding dual volt MMC card
support by the controller which will be later passed to the host driver via
platform data.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Acked-by: Benoit Cousson<b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The MMC controller on the OMAP2420 is different from those
on the OMAP2430, OMAP3 and OMAP4 families - all of the latter
are identical. The one on the OMAP2420 is closer to that
on OMAP1 chips.
Currently, the n8x0 is the only OMAP2420 platform supported
in mainline which registers the MMC controller. Upcoming
changes to register the controllers using hwmod data are
potentially invasive. To reduce the risk, separate out the
2420 controller registration from the common init function
and update its only user. Also seperating out mux settings
for OMAP2420.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Chris Ball <cjb@laptop.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The prototype and defination of functions usb_ehci_init and
usb_ohci_init are removed. The ehci and ohci devices are
removed since usbhs device contains both ehci and ohci details.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
A new usbhs platform device is defined;
this device will be the parent device of ehci and
ohci platform devices. the usbhs_init function
is defined which does the usbhs device initialization
and I/O mux of ehci and ohci.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
enabling and disabling the common clocks for ehci
and ohci is implemented. usbhs is a common parent
platform driver for EHCI and OHCI driver. This driver
receives the clock enable and disable requests
from ehci and ohci drivers.The UHH and TLL
initialization is also performed.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Create the ehci and ohci specific platform data structures.
The port enum values are made common for both ehci and ohci.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The patch below removes an extra "l" in the word.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
On non-OMAP2 and non-OMAP3 kernel configs, turn omap2_sdrc_init() into
a no-op. Otherwise, compilation breaks on an OMAP4-only config with
the current omap-for-linus branch:
arch/arm/mach-omap2/built-in.o: In function `omap2_init_common_devices':
../mach-omap2/io.c:421: undefined reference to `omap2_sdrc_init'
Thanks to Sergei Shtylyov <sshtylyov@mvista.com> for suggesting the use
of a empty static inline function rather than a macro.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
[tony@atomide.com: updated not to use __init for inline omap2_sdrc_init]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add omap_hwmod_setup_one(), which is intended for use early in boot to
selectively setup the hwmods needed for system clocksources and
clockevents, and any other hwmod that is needed in early boot.
omap_hwmod_setup_all() can then be called later in the boot process.
The point is to minimize the amount of code that needs to be run
early.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Rename omap_hwmod_init() to omap_hwmod_register(). Rename
omap_hwmod_late_init() to omap_hwmod_setup_all(). Also change all of
the callers to reflect the new names. While here, update some
copyrights.
Suggested by Tony Lindgren <tony@atomide.com>.
N.B. The comment in mach-omap2/serial.c may no longer be correct, given
recent changes in init order.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
On OMAP4, the dpll post divider outputs (MX outputs)
along with clockout_x2 output provide a way to allow/deny
hardware level autogating.
Allowing autoidle would mean that the hw would autogate
this clock when there is no dependency for it.
Denying idle would mean that this clock output will be
forced to stay enabled.
Add dpll api's to read/allow/deny idle control
for these dpll mx postdividers.
NOTE: The gatectrl bit set to 0 allows gatectrl,
and the bit set to 1 denies gatectrl.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: moved OMAP4-specific DPLL control code to
mach-omap2/dpll44xx.c; added some documentation for CLOCK_CLKOUTX2]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Attempt to enable autoidle for as many clocks as possible in the
OMAP2+-common CONFIG_OMAP_RESET_CLOCKS code. Currently, this only
enables DPLL autoidle for OMAP3/4 DPLLs; but future patches will
enable autoidle for other clocks and the OMAP2 DPLL/APLLs.
In the long run, we should probably get rid of
CONFIG_OMAP_RESET_CLOCKS, and unconditionally run the code that it
selects. Otherwise, the state of the clock tree won't match the
hardware state - this could result in clocks being enabled or disabled
unpredictably.
Based on a patch by Rajendra Nayak <rnayak@ti.com> that did this in
the pm34xx.c/pm44xx.c code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
On OMAP various clock nodes (dpll's, mx post dividers, interface clocks)
support hardware level autogating which can be controlled from
software.
Support such functionality by adding two new function pointer
allow_idle and deny_idle in the clkops structure.
These function pointers can be populated for any clock
node which supports hardware level autogating.
Also add 2 new functions (omap_clk_enable_autoidle_all and
omap_clk_disable_autoidle_all) which can be called from
architecture specific PM core code, if hardware level
autogating (for all supported clock nodes) is to be
enabled or disabled.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: use spinlock rather than mutex due to race; renamed functions;
functions now return ints]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add support to register an isr for IOMMU fault situations and adapt it
to allow such (*isr)() to be used as fault callback. Drivers using IOMMU
module might want to be informed when errors happen in order to debug it
or react.
Signed-off-by: David Cohen <dacohen@gmail.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Information like base address and DMA channel nubers should no longer
be obtained using macros. These information should be obtained from
hwmod database. Hence the macros that define the base address are removed.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
After McBSP driver is hwmod adapted, the information about the hw would be
obtained from the hwmod database by the mcbsp driver. Since DMA programming is
handled by the client driver, APIs are provided to pass the DMA channel number
and base address of data register required by the client driver for DMA
programming.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pm runtime support for McBSP driver.
Reference to fclk is not removed because it is required when the
functional clock is switched from one source to another.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
McBSP2/3 in OMAP3 has sidetone feature which requires autoidle
to be disabled before starting the sidetone. Also SYSCONFIG
register has to be set with smart idle or no idle depending on the
dma op mode (threshold or element sync). For doing these operations
dynamically at runtime, omap_device APIs are used to modify SYSCONFIG register.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
[tony@atomide.com: updated to compile without omap_device idle calls]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Modify OMAP2+ McBSP to use omap hwmod framework APIs
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since the sidetone block is tightly coupled to the mcbsp, sidetone information
is directly added to mcbsp2 & 3 hwmod dev_attr.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Added a name to address space belonging to SDMA and MPU facilitating
the driver to get the address space info by name. Added a revision
member inorder to facilitate the driver to differentiate between
mcbsp in different omap.
Also added a platform_get_irq in probe to get irq number by index since
from OMAP4, there will be a single irq line.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add McBSP hwmod data for OMAP3.
Added a revision member inorder to facilitate the driver to
differentiate between mcbsp in different omap.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add McBSP hwmod data for OMAP2430.
Added a revision member inorder to facilitate the driver to
differentiate between mcbsp in different omap.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Implement McBSP as platform device and add support for
registering through platform device layer using resource
structures.
Later in this patch series, OMAP2+ McBSP driver would be modified to
use hwmod framework after populating the omap2+ hwmod database.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adds support for resource API to get address space info other than just MPU.
The drivers can now use platform_get_resource_byname() to get resource of
type 'IORESOURCE_MEM' by name.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP IOMMU generic layer doesn't need ot print function name during
error messages. Print module name instead which is more useful.
Signed-off-by: David Cohen <dacohen@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In a modular build of the iommu code it's possible that the arch iommu code
isn't loaded when trying to enable the iommu. Instead of blindly following a
null pointer return -NODEV in that case.
Signed-off-by: Martin Hostettler <martin@neutronstar.dyndns.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A new file display.c is introduced for display driver init, which adds a function
omap_display_init to do the DSS driver registration. This is the first step in moving
away registration of DSS from board files into a common place.
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Hwmod needs database of all IPs in a system. This patch generates the hwmod
database for Display Sub System applicable for OMAP3430 and
OMAP36xx. DSS is also considered as an IP as DISPC, RFBI and named as dss_core.
For all the IP modules in DSS, same clock is needed for enabling. Hwmod sees
DSS IPs as independent IPs, so same clock has to be repeated for .main_clk in
each IP.
This patch defines separate hwmod databases for OMAP3430ES1 and (OMAP3430ES2 and
OMAP36xx) as OMAP3430ES1 does not have IDLEST bit to poll on for dss IP, and also
the firewall regions are different between 3430es1 and later.
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Hwmod needs database of all IPs in a system. This patch generates the hwmod
database for OMAP2420 Display Sub System,. Since DSS is also considered as an
IP as DISPC, RFBI, name it as dss_core.
Acked-by: Benoit Cousson <b-cousson@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Introduced the suspend/resume function for the OMAP4430 internal PHY.
This will be used by the twl6030-usb transceiver driver.
Moved the clock enable/disable function calls and power on/off of the PHY
code from power on/off functions to suspend/resume function.
Pass the suspend function through board data for OMAP4430sdp and OMAP4panda.
This will be used by the twl6030-usb transceiver driver.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allow OMAP4 ES2.1 and ES2.2 revisions to be recognized in the
omap4_check_revision() function.
Mainly, ES2.1 has fixes that allow LPDDR to be used at 100% OPP (400MHz).
ES2.2 additionally has a couple of power management fixes (to reduce
leakage), an I2C1 SDA line state fix, and a floating point write
corruption fix (cortex erratum).
Even though the current mainline support doesn't need to distinguish
between ES2.X versions, it's still useful to know the correct silicon
rev when issues are reported. Moreover, these id checks can be used by
power management code that selects suitable OPPs considering the
memory speed limitation on ES2.0.
For details about the silicon errata on OMAP4430, refer
http://focus.ti.com/pdfs/wtbu/SWPZ009A_OMAP4430_Errata_Public_vA.pdf
Signed-off-by: Nishant Kamat <nskamat@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Declaration of exported function 'iopgtable_lookup_entry' is missing from
header file. Currently we have a sparse warning as it's not being used
externally. Adding its declaration to avoid such warning and allow its usage
in future.
Signed-off-by: David Cohen <dacohen@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OneNAND version ID may not give the highest frequency
supported and some OneNAND's have setup times that are
clock dependent. Let the board provide that information.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OneNAND frequency is determined when calculating
GPMC timings. Return that value instead of determining it
again in the OMAP OneNAND driver.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch overrides nand ecc layout and bad block descriptor (for 8-bit
device) to support hw ecc in romcode layout. So as to have in sync with ecc
layout throughout; i.e. x-loader, u-boot and kernel.
This enables to flash x-loader, u-boot, kernel, FS images from kernel itself
and compatiable with other tools.
This patch does not enables this feature by default and need to pass from
board file to enable for any board.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch makes it possible to select sw or hw (different layout options)
ecc scheme supported by omap nand driver.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Configure the FIFO THREASHOLD value different for read and write to keep busy
both filling and to drain out of FIFO at reading and writing.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
add support the irq mode in GPMC.
gpmc_init() function move after omap_init_irq() as it has dependecy on irq.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
nand transfer type (sDMA, Polled, prefetch) can be select from board file,
enabling all transfer type in driver, by default.
this helps in multi-omap build and to select different transfer type for
different board.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As PHYS_OFFSET will be becoming a variable, we can't have it used in
initializers nor assembly code. Replace those in generic code with
a run-time initialization. Replace those in platform code using the
individual platform specific PLAT_PHYS_OFFSET.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: David Brown <davidb@codeaurora.org>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This uncouple PHYS_OFFSET from the platform definitions, thereby
facilitating run-time computation of the physical memory offset.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Magnus Damm <damm@opensource.se>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The omap44xx_sram_init() implements functionality to push some
code on SRAM whenever the code can't be executed from external
memory. The low power and DVFS code can be executed from
external DDR itself thanks to OMAP4 memory controller hardware
support. So on OMAP4, sram_push kind of functionality isn't needed.
Hence remove the FIXME warning added for implementing sram push
feature on OMAP4.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cleans up all base address definitions for omap_mcspi
and adapts the device registration and driver to hwmod framework.
Changes involves:
1) Removing all base address macro defines.
2) Using omap-device layer to register device and utilizing data from
hwmod data file for base address, dma channel number, Irq_number,
device attribute(number of chipselect).
3) Appending base address with pdata reg_offset for omap4 boards.
For omap4 all regs used in driver deviate with reg_offset_macros
defined with an value of 0x100. So pass this offset through pdata
and append the same to base address retrieved from hwmod data file
and we are not mapping *_HL_* regs which are not used in driver.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Partha Basak <p-basak2@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update the omap2420 hwmod data with the McSPI info.
Add a device attribute structure which will be used
for passing number of chipselects from hwmod data.
Add revision macros to be passed from rev field from
hwmod.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Moved all the board specific internal PHY functions out of usb_musb.c file
as this file is shared between the OMAP2+ and AM35xx platforms.
There exists a file which has the functions specific to internal PHY
used for OMAP4 platform. Moved all phy specific functions to this file
and passing these functions through board data in the board file.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds support for low level debugging on TI816X boards. Currently the
support for UART3 console on TI816X EVM is added.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates the common machine specific source files with support for
TI816X.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates the common platform files with TI816X support.
The approach taken in this patch is to add TI816X as part of OMAP3 variant where
the cpu class is considered as OMAP34XX and the type is TI816X. This means, both
cpu_is_omap34xx() and cpu_is_ti816x() checks return success on TI816X.
A kernel config option CONFIG_SOC_OMAPTI816X is added under OMAP3 to include
support for TI816X build.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The new init_early hook happens at the end of setup_arch,
which is too early for kzalloc. However, there's no need
to call omap_serial_early_init that early, so fix this
by setting it up as a core_initcall.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Some macros defined in mcbsp.h related to audio, which are never being used
is removed.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Charulatha V <charu@ti.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: G, Manjunath Kondaiah <manjugk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The pointer math in omap_mbox_get() is not quite right, and leads to
passing NULL to strcmp() when searching for an mbox that is not first
in the list.
Convert to using array indexing as is done in all the other functions
which walk the mbox list.
Tested on OMAP2420/n810, OMAP3630/zoom3, OMAP4430/Blaze
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This variable is only assigned in __init functions and never used later.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
All callers of these functions live in .init.text, so these can go there,
too. There they must not be exported anymore, this is no problem though,
as all callers are always built-in.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The new fncpy API is better suited* for copying some
code to SRAM at runtime. This patch changes the ad-hoc
code to the more generic fncpy API.
*: 1. fncpy ensures that the thumb mode bit is propagated,
2. fncpy provides the security of type safety between the
original function and the sram function pointer.
Tested OK on OMAP3 in low power modes (RET/OFF)
using omap2plus_defconfig with !CONFIG_THUMB2_KERNEL.
Compile tested on OMAP1/2 using omap1_defconfig.
Boot tested on OMAP1 & OMAP2
Tested OK with suspend/resume on OMAP2420/n810
Boots fine on osk5912 and n800
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Dave Martin <dave.martin@linaro.org>
Tested-by: Kevin Hilman <khilman@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds a clean method to allow platforms to hook into the reset
code if they require to.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Eliminates the following sparse warning:
arch/arm/plat-omap/dma.c:137:5: warning: symbol 'omap_dma_in_1510_mode' was not declared. Should it be static?
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the following compile warnings:
arch/arm/mach-omap1/board-innovator.c:165:3: warning: initialization
makes integer from pointer without a cast
arch/arm/mach-omap1/board-perseus2.c:305:3: warning: initialization
makes integer from pointer without a cast
arch/arm/mach-omap1/board-fsample.c:338:3: warning: initialization makes
integer from pointer without a cast
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the following compile warning:
arch/arm/plat-omap/i2c.c:120:13: warning:
'omap_pm_set_max_mpu_wakeup_lat_compat' defined but not used
arch/arm/plat-omap/i2c.c:125:38: warning: 'omap_i2c_latency'
defined but not used
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We want to have just CONFIG_ARCH_OMAP2, 3 and 4. The rest
are nowadays just subcategories of these.
Search and replace the following:
ARCH_OMAP2420 SOC_OMAP2420
ARCH_OMAP2430 SOC_OMAP2430
ARCH_OMAP3430 SOC_OMAP3430
No functional changes.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Sourav Poddar <sourav.poddar@ti.com>
With cmwq, there's no reason to use a separate workqueue for mailbox.
Use the system_wq instead. mbox->rxq->work is sync flushed in
omap_mbox_fini() to make sure it's not running on any cpu, which makes
sure that no mbox work is running when omap_mbox_exit() is entered.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Hari Kanigeri <hari.kanigeri@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
When clearing the DMA channel, clear all status bits.
When handling a DMA interrupt, clear only the interrupt
status bits that have been read and are passed to the
channel's interrupt handler, not every status bit.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: G, Manjunath Kondaiah <manjugk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Earlier patches select HAVE_SCHED_CLOCK for omaps. To have working sched_clock
also for MPU timer, we need to implement it in a way where the right one gets
selected during the runtime.
Signed-off-by: Tony Lindgren <tony@atomide.com>
For omap15xx and 730 we need to use the MPU timer
as the 32K timer is not available. For omap16xx
we want to use the 32K timer because of PM. Fix this
by allowing to build in both timers.
Signed-off-by: Tony Lindgren <tony@atomide.com>
After commit dc548fbbd2 ("ARM: omap: convert
sched_clock() to use new infrastructure"), OMAPs that use the 32KiHz
"synchronization timer" as their clocksource crash during boot:
[ 0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz
[ 0.000000] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 0.000000] pgd = c0004000
[ 0.000000] [00000000] *pgd=00000000
[ 0.000000] Internal error: Oops: 80000005 [#1] SMP
[ 0.000000] last sysfs file:
[ 0.000000] Modules linked in:
[ 0.000000] CPU: 0 Tainted: G W (2.6.37-07734-g2467802 #7)
[ 0.000000] PC is at 0x0
[ 0.000000] LR is at sched_clock_poll+0x2c/0x3c
[ 0.000000] pc : [<00000000>] lr : [<c0060b74>] psr: 600001d3
[ 0.000000] sp : c058bfd0 ip : c058a000 fp : 00000000
[ 0.000000] r10: 00000000 r9 : 411fc092 r8 : 800330c8
[ 0.000000] r7 : c05a08e0 r6 : c0034c48 r5 : c05ffc40 r4 : c0034c4c
[ 0.000000] r3 : c05ffe6c r2 : c05a0bc0 r1 : c059f098 r0 : 00000000
[ 0.000000] Flags: nZCv IRQs off FIQs off Mode SVC_32 ISA ARM Segment kernel
[ 0.000000] Control: 10c53c7f Table: 8000404a DAC: 00000017
This is due to the recent ARM init_sched_clock() changes and the late
initialization of the counter_32k clock source. More information here:
http://marc.info/?l=linux-omap&m=129513468605208&w=2
Fix by initializing the counter_32k clocksource during the machine timer
initialization.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
* git://git.infradead.org/mtd-2.6: (59 commits)
mtd: mtdpart: disallow reading OOB past the end of the partition
mtd: pxa3xx_nand: NULL dereference in pxa3xx_nand_probe
UBI: use mtd->writebufsize to set minimal I/O unit size
mtd: initialize writebufsize in the MTD object of a partition
mtd: onenand: add mtd->writebufsize initialization
mtd: nand: add mtd->writebufsize initialization
mtd: cfi: add writebufsize initialization
mtd: add writebufsize field to mtd_info struct
mtd: OneNAND: OMAP2/3: prevent regulator sleeping while OneNAND is in use
mtd: OneNAND: add enable / disable methods to onenand_chip
mtd: m25p80: Fix JEDEC ID for AT26DF321
mtd: txx9ndfmc: limit transfer bytes to 512 (ECC provides 6 bytes max)
mtd: cfi_cmdset_0002: add support for Samsung K8D3x16UxC NOR chips
mtd: cfi_cmdset_0002: add support for Samsung K8D6x16UxM NOR chips
mtd: nand: ams-delta: drop omap_read/write, use ioremap
mtd: m25p80: add debugging trace in sst_write
mtd: nand: ams-delta: select for built-in by default
mtd: OneNAND: lighten scary initial bad block messages
mtd: OneNAND: OMAP2/3: add support for command line partitioning
mtd: nand: rearrange ONFI revision checking, add ONFI 2.3
...
Fix up trivial conflict in drivers/mtd/Kconfig as per DavidW.
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (27 commits)
omap4: Fix ULPI PHY init for ES1.0 SDP
omap3: beaglexm: fix power on of DVI
omap3: igep3: Add omap_reserve functionality
omap3: beaglexm: fix DVI reset GPIO
omap3: beaglexm: fix EHCI power up GPIO dir
omap3: igep2: Add keypad support
omap3: igep3: Fix IGEP module second MMC channel power supply
omap3: igep3: Add USB EHCI support for IGEP module
omap3: clocks: Fix build error 'CK_3430ES2' undeclared here
arm: omap4: pandaboard: turn on PHY reference clock at init
omap2plus: prm: Trvial build break fix for undefined reference to 'omap2_prm_read_mod_reg'
omap2plus: voltage: Trivial linking fix for 'EINVAL' undeclared
omap2plus: voltage: Trivial linking fix 'undefined reference'
omap2plus: voltage: Trivial warning fix 'no return statement'
omap2plus: clockdomain: Trivial fix for build break because of clktrctrl_mask
arm: omap: gpio: don't access irq_desc array directly
omap2+: pm_bus: make functions used as pointers as static
OMAP: GPIO: fix _set_gpio_triggering() for OMAP2+
OMAP2+: TWL: include pm header for init protos
OMAP2+: TWL: make conversion routines static
...
Fix up conflicts in arch/arm/mach-omap2/board-omap3beagle.c ("DVI reset
GPIO" vs "use generic DPI panel driver")
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6: (29 commits)
video: move SH_MIPI_DSI/SH_LCD_MIPI_DSI to the top of menu
fbdev: Implement simple blanking in pseudocolor modes for vt8500lcdfb
video: imx: Update the manufacturer's name
nuc900fb: don't treat NULL clk as an error
s3c2410fb: don't treat NULL clk as an error
video: tidy up modedb formatting.
video: matroxfb: Correct video option in comments and kernel config help.
fbdev: sh_mobile_hdmi: simplify pointer handling
fbdev: sh_mobile_hdmi: framebuffer notifiers have to be registered
fbdev: sh_mobile_hdmi: add command line option to use the preferred EDID mode
OMAP: DSS2: Introduce omap_channel as an omap_dss_device parameter, add new overlay manager.
OMAP: DSS2: Use dss_features to handle DISPC bits removed on OMAP4
OMAP: DSS2: LCD2 Channel Changes for DISPC
OMAP: DSS2: Change remaining DISPC functions for new omap_channel argument
OMAP: DSS2: Introduce omap_channel argument to DISPC functions used by interface drivers
OMAP: DSS2: Represent DISPC register defines with channel as parameter
OMAP: DSS2: Add dss_features for omap4 and overlay manager related features
OMAP: DSS2: Clean up DISPC color mode validation checks
OMAP: DSS2: Add back authors of panel-generic.c based drivers
OMAP: DSS2: remove generic DPI panel driver duplicated panel drivers
...
A panel connects to one of the overlay managers of DSS through some interface block.
On OMAP4, specifying the type of the display is not sufficient to conclude which manager
the panel should be connected to.
Hence, a new member 'channel' is introduced in omap_dss_device structure to determine
which manager the panel uses. The dss_recheck_connections() called in dss_driver_probe()
uses this channel parameter to set the correct manager to the corresponding omap_dss_device.
The channel parameter is used only once to ensure the correct managers are set for each
panel. The parameter dssdev->manager->id will take care of ensuring that the panel and
then the interface driver configures the correct DISPC channel.
Also, add a new Overlay Manager in manager.c, make other changes needed for LCD2 channel.
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Mukund Mittal <mmittal@ti.com>
Signed-off-by: Samreen <samreen@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
DISPC functions are modified in order to work when the manager is LCD2.
This includes:
Adding new IRQs specific to LCD2 and their handling.
Provide dumps of the new manager's registers.
Provide dumps of the new manager's clocks.
Checks for channel for registers DISPC_CONTROL2 and DISPC_CONFIG2
which can't be parametrized.
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Mukund Mittal <mmittal@ti.com>
Signed-off-by: Samreen <samreen@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
On OMAP4, we have a new DISPC channel for Overlay Manager LCD2. There is a set
of regsiters for LCD2 channel similar to the existing LCD channel, like
DISPC_CONTROL2, DISPC_DIVISOR2, DISPC_CONFIG2 and so on.
Introduce new enum members for LCD2 Channel and corresponding Overlay Manager
in display.h.
Represent the following DISPC register defines with channel as a parameter
to differentiate between LCD and LCD2 registers (and also DIGIT in some cases):
DISPC_DEFAULT_COLOR, DISPC_TRANS_COLOR, DISPC_TIMING_H, DISPC_TIMING_V,
DISPC_POL_FREQ, DISPC_DIVISOR, DISPC_SIZE_LCD, DISPC_DATA_CYCLEk,
DISPC_CPR_COEF_R, DISPC_CPR_COEF_G and DISPC_CPR_COEF_B
This parametrization helps in reducing the number of register defines for DISPC.
Replace the existing reads/writes to these registers in this new way.
Also, Introduce defines for registers DISPC_CONTROL2 and DISPC_CONFIG2 which
are used exclusively for LCD2 channel.
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Mukund Mittal <mmittal@ti.com>
Signed-off-by: Samreen <samreen@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Generic DPI panel driver includes the driver and 4 similar panel configurations. It
will match the panel name which is passed from platform data and setup the
right configurations.
With generic DPI panel driver, we can remove those 4 duplicated panel display
drivers. In the future, it is simple for us just add new panel configuration
date in panel-generic-dpi.c to support new display panel.
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Acked-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Enable dss to process color formats with pre-mulitplied alpha.
With this we can have alpha values defined for each pixel
and hence can have different blending values for each pixel.
sysfs entry has been created for this and pre-multiplied alpha
support is turned off by default.
Signed-off-by: Sudeep Basavaraj <sudeep.basavaraj@ti.com>
Signed-off-by: Rajkumar N <rajkumar.nagarajan@ti.com>
Signed-off-by: Samreen <samreen@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
CC arch/arm/mach-omap2/omap_hwmod_common_data.o
In file included from arch/arm/plat-omap/include/plat/omap_hwmod.h:38,
from arch/arm/mach-omap2/omap_hwmod_common_data.c:20:
arch/arm/plat-omap/include/plat/voltage.h: In function 'omap_voltage_late_init':
arch/arm/plat-omap/include/plat/voltage.h:145: error: 'EINVAL' undeclared (first use in this function)
arch/arm/plat-omap/include/plat/voltage.h:145: error: (Each undeclared identifier is reported only once
arch/arm/plat-omap/include/plat/voltage.h:145: error: for each function it appears in.)
make[1]: *** [arch/arm/mach-omap2/omap_hwmod_common_data.o] Error 1
make: *** [arch/arm/mach-omap2] Error 2
The error is reported when omap2plus_defconfig built with CONFIG_PM disabled
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Thara Gopinath <thara@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
LD init/built-in.o
LD .tmp_vmlinux1
arch/arm/mach-omap2/built-in.o: In function `omap2_set_init_voltage':
arch/arm/mach-omap2/pm.c:181: undefined reference to `omap_voltage_domain_lookup'
arch/arm/mach-omap2/built-in.o: In function `omap4_twl_init':
arch/arm/mach-omap2/omap_twl.c:244: undefined reference to `omap_voltage_domain_lookup'
arch/arm/mach-omap2/omap_twl.c:247: undefined reference to `omap_voltage_domain_lookup'
arch/arm/mach-omap2/omap_twl.c:250: undefined reference to `omap_voltage_domain_lookup'
make: *** [.tmp_vmlinux1] Error 1
The error is reported when omap2plus_defconfig built with CONFIG_PM disabled
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Thara Gopinath <thara@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Fix below build warnings
CC arch/arm/mach-omap2/common.o
CC arch/arm/mach-omap2/gpio.o
In file included from arch/arm/plat-omap/include/plat/omap_hwmod.h:38,
from arch/arm/mach-omap2/gpio.c:25:
arch/arm/plat-omap/include/plat/voltage.h: In function 'omap_voltage_register_pmic':
arch/arm/plat-omap/include/plat/voltage.h:137: warning: no return statement in function returning non-void
CC arch/arm/mach-omap2/dma.o
In file included from arch/arm/plat-omap/include/plat/omap_hwmod.h:38,
from arch/arm/mach-omap2/dma.c:32:
arch/arm/plat-omap/include/plat/voltage.h: In function 'omap_voltage_register_pmic':
arch/arm/plat-omap/include/plat/voltage.h:137: warning: no return statement in function returning non-void
CC arch/arm/mach-omap2/wd_timer.o
In file included from arch/arm/plat-omap/include/plat/omap_hwmod.h:38,
from arch/arm/mach-omap2/wd_timer.c:15:
arch/arm/plat-omap/include/plat/voltage.h: In function 'omap_voltage_register_pmic':
arch/arm/plat-omap/include/plat/voltage.h:137: warning: no return statement in function returning non-void
CC arch/arm/mach-omap2/prm44xx.o
CC arch/arm/mach-omap2/omap_hwmod.o
In file included from arch/arm/plat-omap/include/plat/omap_hwmod.h:38,
from arch/arm/mach-omap2/omap_hwmod.c:145:
arch/arm/plat-omap/include/plat/voltage.h: In function 'omap_voltage_register_pmic':
arch/arm/plat-omap/include/plat/voltage.h:137: warning: no return statement in function returning non-void
CC arch/arm/mach-omap2/omap_hwmod_common_data.o
In file included from arch/arm/plat-omap/include/plat/omap_hwmod.h:38,
from arch/arm/mach-omap2/omap_hwmod_common_data.c:20:
arch/arm/plat-omap/include/plat/voltage.h: In function 'omap_voltage_register_pmic':
arch/arm/plat-omap/include/plat/voltage.h:137: warning: no return statement in function returning non-void
The error is reported when omap2plus_defconfig built with CONFIG_PM disabled
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Thara Gopinath <thara@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Instead of accessing the irq_desc array directly
we can use irq_to_desc(irq). That will allow us to,
if wanted, select SPARSE_IRQ and irq_descs will be
added to a radix tree, instead of a array.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
In case on OMAP2+ we call set_24xx_gpio_triggering() instead of
updating reg and l values. However, at the end of the function we
perform a write:
__raw_writel(l, reg);
So on OMAP2+ we end up writing 0 to the bank->base which is not
correct (typically this points to GPIO_REVISION register).
Fix this by returning immediately after call to
set_24xx_gpio_triggering().
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (144 commits)
USB: add support for Dream Cheeky DL100B Webmail Notifier (1d34:0004)
USB: serial: ftdi_sio: add support for TIOCSERGETLSR
USB: ehci-mxc: Setup portsc register prior to accessing OTG viewport
USB: atmel_usba_udc: fix freeing irq in usba_udc_remove()
usb: ehci-omap: fix tll channel enable mask
usb: ohci-omap3: fix trivial typo
USB: gadget: ci13xxx: don't assume that PAGE_SIZE is 4096
USB: gadget: ci13xxx: fix complete() callback for no_interrupt rq's
USB: gadget: update ci13xxx to work with g_ether
USB: gadgets: ci13xxx: fix probing of compiled-in gadget drivers
Revert "USB: musb: pm: don't rely fully on clock support"
Revert "USB: musb: blackfin: pm: make it work"
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
...
Manually fix up trivial conflicts in USB Kconfig changes in:
arch/arm/mach-omap2/Kconfig
arch/sh/Kconfig
drivers/usb/Kconfig
drivers/usb/host/ehci-hcd.c
and annoying chip clock data conflicts in:
arch/arm/mach-omap2/clock3xxx_data.c
arch/arm/mach-omap2/clock44xx_data.c
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (243 commits)
omap2: Make OMAP2PLUS select OMAP_DM_TIMER
OMAP4: hwmod data: Fix alignment and end of line in structurefields
OMAP4: hwmod data: Move the DMA structures
OMAP4: hwmod data: Move the smartreflex structures
OMAP4: hwmod data: Fix missing SIDLE_SMART_WKUP in smartreflexsysc
arm: omap: tusb6010: add name for MUSB IRQ
arm: omap: craneboard: Add USB EHCI support
omap2+: Initialize serial port for dynamic remuxing for n8x0
omap2+: Add struct omap_board_data and use it for platform level serial init
omap2+: Allow hwmod state changes to mux pads based on the state changes
omap2+: Add support for hwmod specific muxing of devices
omap2+: Add omap_mux_get_by_name
OMAP2: PM: fix compile error when !CONFIG_SUSPEND
MAINTAINERS: OMAP: hwmod: update hwmod code, data maintainership
OMAP4: Smartreflex framework extensions
OMAP4: hwmod: Add inital data for smartreflex modules.
OMAP4: PM: Program correct init voltages for scalable VDDs
OMAP4: Adding voltage driver support
OMAP4: Register voltage PMIC parameters with the voltage layer
OMAP3: PM: Program correct init voltages for VDD1 and VDD2
...
Fix up trivial conflict in arch/arm/plat-omap/Kconfig
Prevent OneNAND's voltage regulator from going to sleep while
OneNAND is in use, by explicitly enabling and disabling the
regulator as appropriate.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Replace the page_to_dma() and dma_to_page() macros with their PFN
equivalents. This allows us to map parts of memory which do not have
a struct page allocated to them to bus addresses. This will be used
internally by dma_alloc_coherent()/dma_alloc_writecombine().
Build tested on Versatile, OMAP1, IOP13xx and KS8695.
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It appears that arch/arm/mach-omap2/timer-gp.o is needed by OMAP2PLUS.
Since timer-gp.o has direct dependencies on omap_dm_timer_*, it seems
correct for the architecture to depend upon OMAP_DM_TIMER, otherwise
unsuspecting integrators will be faced with a whole bunch of linker
errors at the end of their kernel build:
arch/arm/mach-omap2/built-in.o: In function `omap2_gp_timer_set_mode':
/home/bgamari/trees/linux-2.6/arch/arm/mach-omap2/timer-gp.c:84: undefined reference to `omap_dm_timer_stop'
/home/bgamari/trees/linux-2.6/arch/arm/mach-omap2/timer-gp.c:88: undefined reference to `omap_dm_timer_get_fclk'
/home/bgamari/trees/linux-2.6/arch/arm/mach-omap2/timer-gp.c:90: undefined reference to `omap_dm_timer_set_load_start'
...
Signed-off-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This allows adding hwmod specific pads dynamically during the
platform device init.
Note that we don't currently have the hwmod specific signals
listed in the hwmod data, but struct omap_hwmod_mux_info will
make that possible if necessary.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert omap to use the new sched_clock() infrastructure for extending
32bit counters to full 64-bit nanoseconds.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ftrace requires sched_clock() to be notrace. Ensure that all
implementations are so marked. Also make sure that they include
linux/sched.h
Also ensure OMAP clocksource read functions are marked notrace as
they're used for sched_clock() too.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Eric Miao <eric.y.miao@gmail.com>
Tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch extends the smartreflex framework to support
OMAP4. The changes are minor like compiling smartreflex Kconfig
option for OMAP4 also, and a couple of OMAP4 checks in
the smartreflex framework.
The change in sr_device.c where new logic has to be introduced
for reading the efuse registers is due to the fact that in OMAP4
the efuse registers are 24 bit aligned. A __raw_readl will
fail for non-32 bit aligned address and hence the 8-bit read
and shift.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
OMAP4 has three scalable voltage domains vdd_mpu, vdd_iva
and vdd_core. This patch adds the voltage tables and other
configurable voltage processor and voltage controller
settings to control these three scalable domains in OMAP4.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Smartreflex Class3 implementation continuously monitors
silicon performance and instructs the Voltage Processors
to increase or decrease the voltage.
This patch adds smartreflex class 3 driver. This driver hooks
up with the generic smartreflex driver smartreflex.c to abstract
out class specific implementations out of the generic driver.
Class3 driver is chosen as the default class driver for smartreflex.
If any other class driver needs to be implemented, the init of that
driver should be called from the board file. That way the new class driver
will over-ride the Class3 driver.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
SmartReflex modules do adaptive voltage control for real-time
voltage adjustments. With Smartreflex the power supply voltage
can be adapted to the silicon performance(manufacturing process,
temperature induced performance, age induced performance etc).
There are differnet classes of smartreflex implementation.
Class-0: Manufacturing Test Calibration
Class-1: Boot-Time Software Calibration
Class-2: Continuous Software Calibration
Class-3: Continuous Hardware Calibration
Class-4: Fully Integrated Power Management
OMAP3 has two smartreflex modules one associated with VDD MPU and the
other associated with VDD CORE.
This patch adds support for smartreflex driver. The driver is designed
for Class-1 , Class-2 and Class-3 support and is a platform driver.
Smartreflex driver can be enabled through a Kconfig option
"SmartReflex support" under "System type"->"TI OMAP implementations" menu.
Smartreflex autocompensation feature can be enabled runtime through
a debug fs option.
To enable smartreflex autocompensation feature
echo 1 > /debug/voltage/vdd_<X>/smartreflex/autocomp
To disable smartreflex autocompensation feature
echo 0 > /debug/voltage/vdd_<X>/smartreflex/autocomp
where X can be mpu, core , iva etc.
This patch contains code originally in linux omap pm branch.
Major contributors to this driver are
Lesly A M, Rajendra Nayak, Kalle Jokiniemi, Paul Walmsley,
Nishant Menon, Kevin Hilman.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch extends the device hwmod structure to contain
info about the voltage domain to which the device belongs to.
This is needed to support a device based DVFS where the
device knows which voltage domain it belongs to.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds voltage driver support for OMAP3. The driver
allows configuring the voltage controller and voltage
processors during init and exports APIs to enable/disable
voltage processors, scale voltage and reset voltage.
The driver maintains the global voltage table on a per
VDD basis which contains the various voltages supported by the
VDD along with per voltage dependent data like smartreflex
efuse offset, errminlimit and voltage processor errorgain.
The driver also allows the voltage parameters dependent on the
PMIC to be passed from the PMIC file through an API.
The driver allows scaling of VDD voltages either through
"vc bypass method" or through "vp forceupdate method" the
choice being configurable through the board file.
This patch contains code originally in linux omap pm branch
smartreflex driver. Major contributors to this driver are
Lesly A M, Rajendra Nayak, Kalle Jokiniemi, Paul Walmsley,
Nishant Menon, Kevin Hilman. The separation of PMIC parameters
into a separate structure which can be populated from
the PMIC file is based on the work of Lun Chang from Motorola
in an internal tree.
Signed-off-by: Thara Gopinath <thara@ti.com>
[khilman: fixed link error for OMAP2-only defconfig]
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Most keypad drivers make use of the <linux/input/matrix_keypad.h>
defined macros, structures and inline functions.
Convert omap-keypad driver to use those as well, as suggested by a
compile time warning, hardcoded into the OMAP <palt/keypad.h>.
Created against linux-2.6.37-rc5.
Tested on Amstrad Delta.
Compile tested with omap1_defconfig and omap2plus_defconfig shrinked to
board-h4.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Reviewed-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
For devices which have not (yet) been converted to use omap_device,
implement the context loss counter using the "brutal method" as
originally proposed by Paul Walmsley[1].
The dummy context loss counter is incremented every time it is
checked, but only when off-mode is enabled. When off-mode is
disabled, the dummy counter stops incrementing.
Tested on 36xx/Zoom3 using MMC driver, which is currently the
only in-tree user of this API.
This patch should be reverted after all devices are converted to using
omap_device.
[1] http://marc.info/?l=linux-omap&m=129176260000626&w=2
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
[paul@pwsan.com: fixed compile warning; fixed to compile on OMAP1]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Implement OMAP PM layer omap_pm_get_dev_context_loss_count() API by
creating similar APIs at the omap_device and omap_hwmod levels. The
omap_hwmod level call is the layer with access to the powerdomain
core, so it is the place where the powerdomain is queried to get the
context loss count.
The new APIs return an unsigned value that can wrap as the
context-loss count grows. However, the wrapping is not important as
the role of this function is to determine context loss by checking for
any difference in subsequent calls to this function.
Note that these APIs at each level can return zero when no context
loss is detected, or on errors. This is to avoid returning error
codes which could potentially be mistaken for large context loss
counters.
NOTE: only works for devices which have been converted to use
omap_device/omap_hwmod.
Longer term, we could possibly remove this API from the OMAP PM layer,
and instead directly use the omap_device level API.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
J-Type DPLLs have additional configuration parameters that need to
be programmed when setting the multipler and divider for the DPLL.
These parameters being the sigma delta divider (SD_DIV) for the DPLL
and the digital controlled oscillator (DCO) to be used by the DPLL.
The current code is implemented specifically to configure the
OMAP3630 PER J-Type DPLL. The OMAP4430 USB DPLL is also a J-Type DPLL
and so this code needs to be updated to work for both OMAP3 and OMAP4
devices and any other future devices that have J-TYPE DPLLs.
For the OMAP3630 PER DPLL both the SD_DIV and DCO paramenters are
used but for the OMAP4430 USB DPLL only the SD_DIV field is used.
The current implementation will only program the SD_DIV and DCO
fields if the DPLL has both and hence this does not work for
OMAP4430.
In order to make the code more generic add two new fields to the
dpll_data structure for the SD_DIV field and DCO field bit-masks
and only program these fields if the masks are defined for a specific
DPLL. This simplifies the code and allows us to remove the flag
DPLL_NO_DCO_SEL.
Tested on OMAP36xx Zoom3 and OMAP4 Blaze.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: removed explicit inlining and added '_' prefix on lookup_*()
functions; added testing info to commit message; added 35xx comments back in]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The new OMAP4 IPs introduced a new idle mode named smart-idle with wakeup.
This new idlemode replaces the enawakeup for the new IPs but seems to
coexist as well for some legacy IPs (UART, GPIO, MCSPI...)
Add the new SIDLE_SMART_WKUP flag to mark the IPs that support this
capability.
The omap_hwmod_44xx_data.c will have to be updated to add this new flag.
Enable this new mode when applicable in _enable_wakeup, _enable_sysc and
_idle_sysc.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Tested-by: Sebastien Guiriec <s-guiriec@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Do not allow omap_hwmod_register to be used outside the core
hwmod code. An omap_hwmod should be registered only at init time.
Remove the omap_hwmod_unregister that is not used today since the
hwmod list will be built once at init time and never be modified
at runtime.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Clarify the usage of the struct omap_clk.cpu flags (e.g., CK_*) to use
bits only for individual SoC variants (e.g., CK_3430ES1, CK_3505,
etc.). Superset flags, such as CK_3XXX or CK_AM35XX, are now defined
as disjunctions of individual SoC variant flags. This simplifies the
definition and use of these flags. struct omap_clk record definitions
can now simply specify the bitmask of actual SoCs that the records are
valid for. The clock init code can simply set a single CPU type mask
bit for the SoC that is currently in use, and test against that,
rather than needing to set some combination of flags.
Similarly, clarify the use of struct clksel_rate.flags. The bit
allocated for RATE_IN_3XXX has been reassigned, and RATE_IN_3XXX has
been defined as a disjunction of the 34xx and 36xx rate flags. The
advantages are the same as the above.
Clarify the usage of struct omap_clk.cpu flags such as CK_34XX to only
apply to the SoCs that they name, e.g., OMAP34xx chips. The previous
practice caused significantly different SoCs, such as OMAP36xx, to be
included in CK_34XX. In my opinion, this is much more intuitive.
Similarly, clarify the use of struct clksel_rate.flags, such that
RATE_IN_3430ES2PLUS now only applies to 34xx chips with ES level >= 2
- it does not apply to OMAP36xx.
...
At some point, it probably makes sense to collapse the CK_* and
RATE_IN_* flags together into a single bitfield, and possibly use the
existing CHIP_IS_OMAP* flags for platform detection.
...
This all seems to work fine on OMAP34xx and OMAP36xx Beagle. Not sure
if it works on Sitara or the TI816X, unfortunately I don't have any
here to test with.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Move the padconf save code from pm34xx.c to the System Control Module
code in mach-omap2/control.c. This is part of the general push to
move direct register access from middle-layer core code to low-level
core code, so the middle-layer code can be abstracted to work on
multiple platforms and cleaned up.
In the medium-to-long term, this code should be called by the mux
layer code, not the PM idle code. This is because, according to the
TRM, saving the padconf only needs to be done when the padconf
changes[1].
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
1. OMAP34xx Multimedia Device Silicon Revision 3.1.x [Rev. ZH] [SWPU222H]
Section 4.11.4 "Device Off-Mode Sequences"
The OMAP powerdomain code and data is all OMAP2+-specific. This seems
unlikely to change any time soon. Move plat-omap/include/plat/powerdomain.h
to mach-omap2/powerdomain.h. The primary point of doing this is to remove
the temptation for unrelated upper-layer code to access powerdomain code
and data directly.
As part of this process, remove the references to powerdomain data
from the GPIO "driver" and the OMAP PM no-op layer, both in plat-omap.
Change the DSPBridge code to point to the new location for the
powerdomain headers. The DSPBridge code should not be including the
powerdomain headers; these should be removed.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Omar Ramirez Luna <omar.ramirez@ti.com>
Cc: Felipe Contreras <felipe.contreras@gmail.com>
Cc: Greg Kroah-Hartman <greg@kroah.com>
The OMAP clockdomain code and data is all OMAP2+-specific. This seems
unlikely to change any time soon. Move plat-omap/include/plat/clockdomain.h
to mach-omap2/clockdomain.h. The primary point of doing this is to remove
the temptation for unrelated upper-layer code to access clockdomain code
and data directly.
DSPBridge also uses the clockdomain headers for some reason, so,
modify it also. The DSPBridge code should not be including the
clockdomain headers; these should be removed.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Omar Ramirez Luna <omar.ramirez@ti.com>
Cc: Felipe Contreras <felipe.contreras@gmail.com>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reverse some of the effects of commit
84c0c39aec ("ARM: OMAP4: PM: Make OMAP3
Clock-domain framework compatible for OMAP4"). On OMAP2/3, the
CM_CLKSTCTRL register is at a constant offset from the powerdomain's
CM instance.
Also, remove some of the direct CM register access from the
clockdomain code, moving it to the OMAP2/3 CM code instead. The
intention here is to simplify the clockdomain code. (The long-term
goal is to move all direct CM register access across the OMAP core
code to the appropriate cm*.c file.)
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Add PRCM partition, CM instance register address offset, and clockdomain
register address offset to each OMAP4 struct clockdomain record. Add OMAP4
clockdomain code to use this new data to access registers properly.
While here, clean up some nearby clockdomain code to allocate auto variables
in my recollection of Linus's preferred style.
The autogeneration scripts have been updated.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
OMAP4 powerdomain control registers are split between the PRM hardware
module and the PRCM_MPU local PRCM. Add this PRCM partition
information to each OMAP4 powerdomain record, and convert the OMAP4
powerdomain function implementations to use the OMAP4 PRM instance
functions.
Also fixes a potential null pointer dereference of pwrdm->name.
The autogeneration scripts have been updated.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Now that OMAP4-specific PRCM functions have been added, distinguish the
existing OMAP2/3-specific PRCM functions by prefixing them with "omap2_".
This patch should not result in any functional change.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
In some ways, the OMAP4 PRCM register layout is quite different than
the OMAP2/3 PRCM register layout. For example, on OMAP2/3, from a
register layout point of view, all CM instances were located in the CM
subsystem, and all PRM instances were located in the PRM subsystem.
OMAP4 changes this. Now, for example, some CM instances, such as
WKUP_CM and EMU_CM, are located in the system PRM subsystem. And a
"local PRCM" exists for the MPU - this PRCM combines registers that
would normally appear in both CM and PRM instances, but uses its own
register layout which matches neither the OMAP2/3 PRCM layout nor the
OMAP4 PRCM layout.
To try to deal with this, introduce some new functions, omap4_cminst*
and omap4_prminst*. The former is to be used when writing to a CM
instance register (no matter what subsystem or hardware module it
exists in), and the latter, similarly, with PRM instance registers.
To determine which "PRCM partition" to write to, the functions take a
PRCM instance ID argument. Subsequent patches add these partition IDs
to the OMAP4 powerdomain and clockdomain definitions.
As far as I can see, there's really no good way to handle these types
of register access inconsistencies. This patch seemed like the least
bad approach.
Moving forward, the long-term goal is to remove all direct PRCM
register access from the PM code. PRCM register access should go
through layers such as the powerdomain and clockdomain code that can
hide the details of how to interact with the specific hardware
variant.
While here, rename cm4xxx.c to cm44xx.c to match the naming convention
of the other OMAP4 PRCM files.
Thanks to Santosh Shilimkar <santosh.shilimkar@ti.com>, Rajendra Nayak
<rnayak@ti.com>, and Benoît Cousson <b-cousson@ti.com> for some comments.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
The OMAP3 PRM module is in the WKUP powerdomain, which is always
powered when the chip is powered, so it shouldn't be necessary to save
and restore those PRM registers. Remove the PRM register save/restore
code, which should save several microseconds during off-mode
entry/exit, since PRM register accesses are relatively slow.
While doing so, move the CM register save/restore code into
CM-specific code. The CM module has been distinct from the PRM module
since 2430.
This patch includes some minor changes to pm34xx.c.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Tero Kristo <tero.kristo@nokia.com>
Cc: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
In preparation for adding OMAP4-specific PRCM accessor/mutator
functions, split the existing OMAP2/3 PRCM code into OMAP2/3-specific
files. Most of what was in mach-omap2/{cm,prm}.{c,h} has now been
moved into mach-omap2/{cm,prm}2xxx_3xxx.{c,h}, since it was
OMAP2xxx/3xxx-specific.
This process also requires the #includes in each of these files to be
changed to reference the new file name. As part of doing so, add some
comments into plat-omap/sram.c and plat-omap/mcbsp.c, which use
"sideways includes", to indicate that these users of the PRM/CM includes
should not be doing so.
Thanks to Felipe Contreras <felipe.contreras@gmail.com> for comments on this
patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Omar Ramirez Luna <omar.ramirez@ti.com>
Acked-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Cc: Felipe Contreras <felipe.contreras@gmail.com>
Acked-by: Felipe Contreras <felipe.contreras@gmail.com>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Static data should be declared in .c files, not .h files. It should be
possible to #include .h files at any point without creating multiple
copies of the same data.
We converted the clock data to .c files some time ago. This patch does
the same for the clockdomain data.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Static data should be declared in .c files, not .h files. It should be
possible to #include .h files at any point without creating multiple
copies of the same data.
We converted the clock data to .c files some time ago. This patch does
the same for the powerdomain data.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Put infrastructure in place, so arch specific func pointers
can be hooked up to the platform-independent part of the
framework.
This is in preparation of splitting the powerdomain framework into
platform-independent part (for all omaps) and platform-specific
parts.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
powerdomains.h header today has only static definitions. Adding any
function declarations into it and including it in multiple source file
is expected to cause issues. Hence move all the static definitions
from powerdomains.h file into powerdomains_data.c file.
Also, create a new powerdomain section of the mach-omap2/Makefile, and
rearrange the prcm-common part of the Makefile, now that the
powerdomain code is in its own Makefile section.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: rearrange Makefile changes, tweaked commit message]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Trivial cleanup and documentation changes on the hwmod code and data:
- add some hwmod documentation to indicate flags that should be moved
outside the static hwmod data in a future patch
- remove some unused fields in the struct omap_hwmod_ocp_if and
struct omap_hwmod structures
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Change the per-hwmod mutex to a spinlock. (The per-hwmod lock
serializes most post-initialization hwmod operations such as enable,
idle, and shutdown.) Spinlocks are needed, because in some cases,
hwmods must be enabled from timer interrupt disabled-context, such as
an ISR. The current use-case that is driving this is the OMAP GPIO
block ISR: it can trigger interrupts even with its clocks disabled,
but these clocks are needed for register accesses in the ISR to succeed.
This patch also effectively reverts commit
848240223c - this patch makes
_omap_hwmod_enable() and _omap_hwmod_init() static, renames them back
to _enable() and _idle(), and changes their callers to call the
spinlocking versions. Previously, since omap_hwmod_{enable,init}()
attempted to take mutexes, these functions could not be called while
the timer interrupt was disabled; but now that the functions use
spinlocks and save and restore the IRQ state, it is appropriate to
call them directly.
Kevin Hilman <khilman@deeprootsystems.com> originally proposed this
patch - thanks Kevin.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Benoît Cousson <b-cousson@ti.com>
The standard omap_hwmod.c _reset() code relies on an IP block's
OCP_SYSCONFIG.SOFTRESET register bit to reset the IP block. This
works for most IP blocks on the chip, but unfortunately not all. For
example, initiator-only IP blocks often don't have any MPU-accessible
OCP-header registers, and therefore the MPU can't write to any
OCP_SYSCONFIG registers in that block. Other IP blocks, such as the
IVA and I2C, require a specialized reset sequence.
Since we need to be able to reset these IP blocks as well, allow
custom IP block reset functions to be passed into the hwmod code via a
per-hwmod-class reset function pointer, struct omap_hwmod_class.reset.
If .reset is non-null, then the hwmod _reset() code will call the custom
function instead of the standard OCP SOFTRESET-based code.
As part of this change, rename most of the existing _reset() function
code to _ocp_softreset(), to indicate more clearly that it does not work
for all cases.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Paul Hunt <hunt@ti.com>
Cc: Stanley Liu <stanley_liu@ti.com>
Allow board files and OMAP core code to control the state that some or
all of the hwmods end up in at the end of _setup() (called by
omap_hwmod_late_init() ). Reimplement the old skip_setup_idle code in
terms of this new postsetup state code.
There are two use-cases for this patch: the !CONFIG_PM_RUNTIME case,
in which all IP blocks should stay enabled after _setup() finishes;
and the MPU watchdog case, in which the watchdog IP block should enter
idle if watchdog coverage of kernel initialization is desired, and
should be disabled otherwise.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Charulatha Varadarajan <charu@ti.com>
Some OMAP IP blocks, such as the watchdog timers, cannot be completely
shut down via the standard hwmod shutdown mechanism. This patch
enables the hwmod data files to supply a pointer to a custom
pre-shutdown function via the struct omap_hwmod_class.pre_shutdown
function pointer. If the struct omap_hwmod_class.pre_shutdown
function pointer is non-null, the function will be executed before the
existing hwmod shutdown code runs.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Split omap2_init_common_hw() into two functions. The first,
omap2_init_common_infrastructure(), initializes the hwmod code and
data, the OMAP PM code, and the clock code and data. The second,
omap2_init_common_devices(), handles any other early device
initialization that, for whatever reason, has not been or cannot be
moved to initcalls or early platform devices.
This patch is required for the hwmod postsetup patch, which allows
board files to change the state that hwmods should be placed into at
the conclusion of the hwmod _setup() function. For example, for a
board whose creators wish to ensure watchdog coverage across the
entire kernel boot process, code to change the watchdog's postsetup
state will be added in the board-*.c file between the
omap2_init_common_infrastructure() and omap2_init_common_devices() function
calls.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Add support for DEBUG_LL for Devkit8000.
Devkit8000 uses uart 3 for debug output.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The SRAM PA addresses are locally defined and used at
different places, i.e. SRAM management code and idle sleep code.
The macros are now defined at a centralized place, for
easier maintenance.
Tested on N900 and Beagleboard with full RET and OFF modes,
using cpuidle and suspend.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Nishanth Menon<nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
With new OPP layer, OPP users will access OPP API directly instead of
using OMAP PM layer, so remove all notions of OPPs from the OMAP PM
layer.
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The calculations done with sync_clk are anyway in picoseconds
and switching to picoseconds allows sync_clk values that are
not a whole number of nanoseconds - which is sometimes the
case.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
No need to call this early from init_irq. Also recent changes
initialize GPIO now later, so calling gpio_request from init_irq
will make it fail.
While at it, also remove the unnecessary EXPORT_SYMBOL.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert DMA library into DMA platform driver and make use of
platform data provided by hwmod data base for OMAP2+ onwards.
For OMAP1 processors, the DMA driver in mach-omap uses resource
structures for getting platform data.
Thanks to Tony Lindgren <tony@atomide.com> for fixing various
omap1 issues and testing the same on OSK5912 board.
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add OMAP2430 DMA hwmod data and also add required
DMA device attributes.
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add OMAP2420 DMA hwmod data and also add required
DMA device attributes.
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Implement errata handling to use flags instead of cpu_is_* and
cpu_class_* in the code.
The errata flags are initialized at init time and during runtime we are
using the errata variable (via the IS_DMA_ERRATA macro) to execute the
required errata workaround.
Reused errata handling patch from: Peter Ujfalusi
<peter.ujfalusi@nokia.com>
https://patchwork.kernel.org/patch/231191/
Changes to above patch:
1. Changes are done for converting all the existing errata work arounds
to use this feature.
2. Detailed description for each errata is added.
3. Fixed bug in SET_DMA_ERRATA macro
4. Bit shifting in macro definitions are replaced with BIT() macro
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Prepare DMA library to get converted into DMA driver using platform
device model and hwmod infrastucture(for omap2+, resource structures
for omap1)
The low level read/write macros are replaced with static inline
functions and register offsets are handled through static register
offset tables mapped through enumeration constants.
These low level read/write functions along with static register offset
tables will be moved to respective mach-omap dma files in the later
patches of this series.
There are no functionality changes with these changes except change in
logic for handling 16bit registers of OMAP1.
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The convention for omap device naming is omap_XXX.
Rename the device and driver name in order to stick
to this naming convention.
Change device name in clock nodes as well.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Ben Dooks <ben-i2c@fluff.org>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The naming convention for omap_device is omap_XXX.
Rename the device and driver name in order to stick
to this naming convention.
Remove the hs prefix that is implicit for every OMAP uarts.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Govindraj Raja <govindraj.raja@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With "ARM: CPU hotplug: remove bug checks in platform_cpu_die()", we
now do not use hard_smp_processor_id(), we no longer need to read the
hardware processor ID. Remove the include providing this function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit f2ce623126 (OMAP: WDT: Split OMAP1 and OMAP2PLUS device
registration) removed omap_init_wdt and related structures from
plat-omap/devices.c. However a subsequent commit or merge
seems to have reintroduced these by accident. The caller of
omap_init_wdt was also removed by that commit, and this did
not get restored. So we have the following build warning now:
CC arch/arm/plat-omap/devices.o
arch/arm/plat-omap/devices.c:252: warning: 'omap_init_wdt' defined but not used
Fix this by removing this dead code.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add minimal support for Nokia RM-680 board.
Tested with omap2plus_defconfig.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
[tony@atomide.com: updated to remove omap_gpio_init
Signed-off-by: Tony Lindgren <tony@atomide.com>
* usb-next: (132 commits)
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
usb: gadget: f_ncm.c added
usb: gadget: u_ether: prepare for NCM
usb: pch_udc: Fix setup transfers with data out
usb: pch_udc: Fix compile error, warnings and checkpatch warnings
usb: add ab8500 usb transceiver driver
USB: gadget: Implement runtime PM for MSM bus glue driver
USB: gadget: Implement runtime PM for ci13xxx gadget
USB: gadget: Add USB controller driver for MSM SoC
USB: gadget: Introduce ci13xxx_udc_driver struct
USB: gadget: Initialize ci13xxx gadget device's coherent DMA mask
USB: gadget: Fix "scheduling while atomic" bugs in ci13xxx_udc
USB: gadget: Separate out PCI bus code from ci13xxx_udc
...
It seems dsp-link will do this, and tidspbridge too at some point, but
right now it's not possible to select CONFIG_MPU_BRIDGE_IOMMU.
Cc: Fernando Guzman Lugo <fernando.lugo@ti.com>
Cc: Yogesh Marathe <yogesh_marathe@ti.com>
Signed-off-by: Felipe Contreras <felipe.contreras@nokia.com>
Some IOMMUs cannot use the whole 0x0 - 0xFFFFFFFF range.
With this new API the valid range can be set.
Signed-off-by: Fernando Guzman Lugo <x0095840@ti.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
__iounmap function is wrong for OMAP architecture,
instead use iounmap which will call to the correct function.
Signed-off-by: Fernando Guzman Lugo <x0095840@ti.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
This patch adds superpages support to fixed ad address
inside iommu_kmap function.
Signed-off-by: Fernando Guzman Lugo <x0095840@ti.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
If some fixed da address is wanted to be mapped and the page
is freed but it is used as gap, the mapping will fail.
This patch is fixing that and olny keeps the gap for
not fixed address.
Signed-off-by: Fernando Guzman Lugo <x0095840@ti.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Otherwise multi-omap1 support for omap1 won't work as the cpu_class_is_omap1()
won't work until the SoC is detected.
Note that eventually these will go away, please use ioremap + read/write instead.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adding the twl6030-usb transceiver support for OMAP4 musb driver.
OMAP4 supports 2 types of transceiver interface.
1. UTMI: The PHY is embedded within OMAP4. The transceiver functionality
is split between the twl6030 PMIC chip and OMAP4430. The VBUS, ID pin
sensing and OTG SRP generation part is integrated in TWL6030 and UTMI PHY
functionality is embedded within the OMAP4430.
There is no direct interactions between the MUSB controller and TWL6030
chip to communicate the session-valid, session-end and ID-GND events.
It has to be done through a software by setting/resetting bits in
one of the control module register of OMAP4430 which in turn toggles
the appropriate signals to MUSB controller.
The internal transceiver has functional clocks and
powerdown bits to powerdown the PHY for power saving.
Since there is no option available for having 2 transceiver drivers
for one USB controller, internal PHY specific APIs are passed through
plaform_data function pointers to use in the twl6030-usb transceiver
driver.
2. ULPI interface is provided for off-chip transceivers.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 4814ced511 (OMAP:
control: move plat-omap/control.h to mach-omap2/control.h)
moved <plat/control.h> to another location, preventing
drivers from accessing it, so we need to pass function
pointers from arch code to be able to talk to internal
PHY on AM35x.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Kernel was failing to boot on omap1611 based OSK boards due to
mis-configured SRAM size. Existing code was using a hard-coded value
for 250k, which was then rounded down by PAGE_SIZE. Increasing this to
256k allows kernel to boot on omap1611 SoCs.
Problem reported by and initial fix suggested by Tim Bird.
Thanks to Tony Lindgren for helping diagnose the problem to being
specific to OMAP1611 and not affecting OMAP1610/OMAP1623.
Reported-by: Tim Bird <tim.bird@am.sony.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Initialize asm_irq_flags in omap_init_irq and use it in
get_irqnr_and_base to detect between omap7xx and omap15xx/16xx.
Note that both INT_1510_IH2_IRQ and INT_1510_IH2_IRQ are defined
as 0, so use INT_1510_IH2_IRQ for both of them.
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Defining iounmap() with arguments prevents it from being used as a
function pointer, causing platforms to work around this. Instead,
define it to be a simple macro.
Do the same for __arch_io(re|un)map too.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We need to divide the 15xx/16xx offset by 2 for 7xx. Use bank->stride
for that. This allows us to get rid of the duplicate defines for the
MPUIO registers.
Note that this will cause omap-keypad.c driver to not work on 7xx.
However, the right fix there is to move over to matrix_keypad instead
as suggested by Cory Maccarrone <darkstar6262@gmail.com> and
Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>.
Cc: Cory Maccarrone <darkstar6262@gmail.com>
Acked-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Implement GPIO as a platform device.
GPIO APIs are used in machine_init functions. Hence it is
required to complete GPIO probe before board_init. Therefore
GPIO device register and driver register are implemented as
postcore_initcalls.
omap_gpio_init() does nothing now and this function would be
removed in the next patch as it's usage is spread across most
of the board files.
Inorder to convert GPIO as platform device, modifications are
required in clockxxxx_data.c file for OMAP1 so that device names
can be used to obtain clock instead of getting clocks by
name/NULL ptr.
Use runtime pm APIs (pm_runtime_put*/pm_runtime_get*) for enabling
or disabling the clocks, modify sysconfig settings and remove usage
of clock FW APIs.
Note 1: Converting GPIO driver to use runtime PM APIs is not done as a
separate patch because GPIO clock names are different for various OMAPs
and are different for some of the banks in the same CPU. This would need
usage of cpu_is checks and bank id checks while using clock FW APIs in
the gpio driver. Hence while making GPIO a platform driver framework,
PM runtime APIs are used directly.
Note 2: While implementing GPIO as a platform device, pm runtime APIs
are used as mentioned above and modification is not done in gpio's
prepare for idle/ resume after idle functions. This would be done
in the next patch series and GPIO driver would be made to use dev_pm_ops
instead of sysdev_class in that series only.
Due to the above, the GPIO driver implicitly relies on
CM_AUTOIDLE = 1 on its iclk for power management to work, since the
driver never disables its iclk.
This would be taken care in the next patch series (see Note 3 below).
Refer to
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg39112.html
for more details.
Note 3: only pm_runtime_get_sync is called in gpio's probe() and
pm_runtime_put* is never called. This is to make the implementation
similar to the existing GPIO code. Another patch series would be sent
to correct this.
In OMAP3 and OMAP4 gpio's debounce clocks are optional clocks. They
are enabled/ disabled whenever required using clock framework APIs
TODO:
1. Cleanup the GPIO driver. Use function pointers and register
offest pointers instead of using hardcoded values
2. Remove all cpu_is_ checks and OMAP specific macros
3. Remove usage of gpio_bank array so that only
instance specific information is used in driver code
4. Rename 'method'/ avoid it's usage
5. Fix the non-wakeup gpios handling for OMAP2430, OMAP3 & OMAP4
6. Modify gpio's prepare for idle/ resume after idle functions
to use runtime pm implentation.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Basak, Partha <p-basak2@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: updated for bank specific revision and updated boards]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add GPIO hwmod data for OMAP2420 and add the required
GPIO device attributes in the gpio header file
Also remove "omap24xx.h" header file as it is not required
anymore.
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Paul Walmsley
Tony Lindgren
Tero Kristo
Kishon Vijay Abraham I
omar ramirez
Kevin Hilman
sricharan
Ming Lei
Rajendra Nayak
Kishore Kadiyala
Anand Gadiyar
Keshava Munegowda
Justin P. Mattock
Thara Gopinath
David Cohen
Charulatha V
Martin Hostettler
Sumit Semwal
Senthilvadivu Guruswamy
Hema HK
Nishant Kamat
Adrian Hunter
Sukumar Ghorai
Russell King
Santosh Shilimkar
Hemant Pedanekar
Uwe Kleine-König
Jean Pihet
Russell King - ARM Linux
Aaro Koskinen
Felipe Balbi
Tejun Heo
Linus Torvalds
Lennert Buytenhek
Paul Mundt
Bryan Wu
Rajkumar N
Mika Westerberg
Ben Gamari
Janusz Krzysztofik
Jiri Kosina
Kevin Hilman
Jon Hunter
Benoit Cousson
Thomas Weber
G, Manjunath Kondaiah
Aaro Koskinen
Greg Kroah-Hartman
Felipe Contreras
Guzman Lugo, Fernando
Ajay Kumar Gupta