Allow board files and OMAP core code to control the state that some or
all of the hwmods end up in at the end of _setup() (called by
omap_hwmod_late_init() ). Reimplement the old skip_setup_idle code in
terms of this new postsetup state code.
There are two use-cases for this patch: the !CONFIG_PM_RUNTIME case,
in which all IP blocks should stay enabled after _setup() finishes;
and the MPU watchdog case, in which the watchdog IP block should enter
idle if watchdog coverage of kernel initialization is desired, and
should be disabled otherwise.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Charulatha Varadarajan <charu@ti.com>
Some OMAP IP blocks, such as the watchdog timers, cannot be completely
shut down via the standard hwmod shutdown mechanism. This patch
enables the hwmod data files to supply a pointer to a custom
pre-shutdown function via the struct omap_hwmod_class.pre_shutdown
function pointer. If the struct omap_hwmod_class.pre_shutdown
function pointer is non-null, the function will be executed before the
existing hwmod shutdown code runs.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Split omap2_init_common_hw() into two functions. The first,
omap2_init_common_infrastructure(), initializes the hwmod code and
data, the OMAP PM code, and the clock code and data. The second,
omap2_init_common_devices(), handles any other early device
initialization that, for whatever reason, has not been or cannot be
moved to initcalls or early platform devices.
This patch is required for the hwmod postsetup patch, which allows
board files to change the state that hwmods should be placed into at
the conclusion of the hwmod _setup() function. For example, for a
board whose creators wish to ensure watchdog coverage across the
entire kernel boot process, code to change the watchdog's postsetup
state will be added in the board-*.c file between the
omap2_init_common_infrastructure() and omap2_init_common_devices() function
calls.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
commit bf56f0a666 (2.6.37-rc1), from Nishanth Menon attempted
to fix card detection for PandaBoard, unfortunately, the fix missed
to initialize .gpio_cd member of omap2_hsmmc_info. This results
in a default value of '0', which is a valid GPIO line.
On PandaBoard, the side effect of this is that GPIO line 0 controls
the powering TFP410 DVI chip, and without the fix DVI chip is
inadvertently powered.
Tested-by: David Anders <x0132446@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Raghuveer Murthy <raghuveer.murthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for DEBUG_LL for Devkit8000.
Devkit8000 uses uart 3 for debug output.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The display reset lines are connected to a TPS65930 which may sleep
when changing GPIO values. Use the appropriate function to silence
a nasty warning from gpiolib.
Signed-off-by: Daniel Morsing <daniel.morsing@gmail.com>
Acked-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cosmetic fixes to the code:
- white spaces and tabs,
- alignement,
- comments rephrase and typos,
- multi-line comments
Tested on N900 and Beagleboard with full RET and OFF modes,
using cpuidle and suspend.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Errata covered:
- 1.157 & 1.185
- i443
- i581
Tested on N900 and Beagleboard with full RET and OFF modes,
using cpuidle and suspend.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
- Reworked and simplified the execution paths for better
readability and to avoid duplication of code,
- Added comments on the entry and exit points and the interaction
with the ROM code for OFF mode restore,
- Reworked the existing comments for better readability.
Tested on N900 and Beagleboard with full RET and OFF modes,
using cpuidle and suspend.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Organize the code in the following sections:
- register access macros,
- API functions,
- internal functions.
Tested on N900 and Beagleboard with full RET and OFF modes,
using cpuidle and suspend.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Using macros from existing include files for registers addresses.
Tested on N900 and Beagleboard with full RET and OFF modes,
using cpuidle and suspend.
Based on original patch from Vishwa.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Cc: Vishwanath BS <vishwanath.bs@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The SRAM PA addresses are locally defined and used at
different places, i.e. SRAM management code and idle sleep code.
The macros are now defined at a centralized place, for
easier maintenance.
Tested on N900 and Beagleboard with full RET and OFF modes,
using cpuidle and suspend.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Nishanth Menon<nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Remove unused code:
- macros,
- variables,
- unused semaphore locking API. This API shall be added back
when needed,
- infinite loops for debug.
Tested on N900 and Beagleboard with full RET and OFF modes,
using cpuidle and suspend.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Tested-by: Nishanth Menon<nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Limitation i583: Self_Refresh Exit issue after OFF mode
Issue:
When device is waking up from OFF mode, then SDRC state machine sends
inappropriate sequence violating JEDEC standards.
Impact:
OMAP3630 < ES1.2 is impacted as follows depending on the platform:
CS0: for 38.4MHz as internal sysclk, DDR content seen to be stable, while
for all other sysclk frequencies, varied levels of instability
seen based on varied parameters.
CS1: impacted
This patch takes option #3 as recommended by the Silicon erratum:
Avoid core power domain transitioning to OFF mode. Power consumption
impact is expected in this case.
To do this, we route core OFF requests to RET request on the impacted
revisions of silicon.
Acked-by: Jean Pihet <j-pihet@ti.com>
[nm@ti.com: rebased the code to 2.6.37-rc2- short circuit code changed a bit]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Currently omap3_cpuidle_update_states makes whole sale decision
on which C states to update based on enable_off_mode variable
Instead, achieve the same functionality by independently providing
mpu and core deepest states the system is allowed to achieve and
update the idle states accordingly.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
[khilman: fixed additional user of this API in OMAP CPUidle driver]
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
While coming out of MPU OSWR/OFF states, L2 controller is reseted.
The reset behavior is implementation specific as per ARMv7 TRM and
hence $L2 needs to be invalidated before it's use. Since the
AUXCTRL register is also reconfigured, disable L2 cache before
invalidating it and re-enables it afterwards. This is as per
Cortex-A8 ARM documentation.
Currently this is identified as being needed on OMAP3630 as the
disable/enable is done from "public side" while, on OMAP3430, this
is done in the "secure side".
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[nm@ti.com: ported to 2.6.37-rc2, added hooks to enable the logic only on 3630]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Peter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Erratum id: i608
RTA (Retention Till Access) feature is not supported and leads to device
stability issues when enabled. This impacts modules with embedded memories
on OMAP3630
Workaround is to disable RTA on boot and coming out of core off.
For disabling RTA coming out of off mode, we do this by overriding the
restore pointer for 3630 as the first point of entry before caches are
touched and is common for GP and HS devices. To disable earlier than
this could be possible by modifying the PPA for HS devices, but not for
GP devices.
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[ambresh@ti.com: co-developer]
Signed-off-by: Ambresh K <ambresh@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Introduce errata handling for OMAP3. This patch introduces
errata variable and stub for initialization which will be
filled up by follow-on patches.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Erratum i581 impacts OMAP3 platforms.
PRCM DPLL control FSM removes SDRC_IDLEREQ before DPLL3 locks causing
the DPLL not to be locked at times.
IMPORTANT:
*) This is not a complete workaround implementation as recommended
by the silicon erratum. This is a support logic for detecting lockups and
attempting to recover where possible and is known to provide stability
in multiple platforms.
*) This code is mostly important for inactive and retention. The ROM code
waits for the maximum DLL lock time when resuming from off mode. So for
off mode this code isn't really needed.
*) counters are introduced here for eventual export to userspace once the
cleanups are completed.
This should eventually get refactored as part of cleanups to sleep34xx.S
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Peter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Analysis in TI kernel with ETM showed that using cache mapped flush
in kernel instead of SO mapped flush cost drops by 65% (3.39mS down
to 1.17mS) for clean_l2 which is used during sleep sequences.
Overall:
- speed up
- unfortunately there isn't a good alternative flush method today
- code reduction and less maintenance and potential bug in
unmaintained code
This also fixes the bug with the clean_l2 function usage.
Reported-by: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
[nm@ti.com: ported rkw's proposal to 2.6.37-rc2]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
With new OPP layer, OPP users will access OPP API directly instead of
using OMAP PM layer, so remove all notions of OPPs from the OMAP PM
layer.
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add OPP data for OMAP34xx and OMAP36xx and initialization functions
to populate OPP tables based on current SoC.
introduce an OMAP generic opp initialization routine which OMAP3
and OMAP4+ SoCs can use to register their OPP definitions.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
omap2_common_pm_init is the API where generic system devices like
mpu, l3 etc get initialized. This has to happen really early on
during the boot and not at a later time. This is especially important
with the new opp changes as these devices need to be built before the
opp tables init happen. Today both are device initcalls and it works
just because of the order of compilation. Making this postcore_initcall
is ideal because the omap device layer init happens as a core_initcall
and typically rest of the driver/device inits are arch_initcall or
something lower.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Some bad interaction between the idle and the suspend paths has been
identified: the idle code is called during the suspend enter and exit
sequences. This could cause corruption or lock-up of resources.
The solution is to move the calls to disable_hlt at the very beginning
of the suspend sequence (ex. in omap3_pm_begin instead of
omap3_pm_prepare), and the call to enable_hlt at the very end of
the suspend sequence (ex. in omap3_pm_end instead of omap3_pm_finish).
Tested with RET and OFF on Beagle and OMAP3EVM.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The calculations done with sync_clk are anyway in picoseconds
and switching to picoseconds allows sync_clk values that are
not a whole number of nanoseconds - which is sometimes the
case.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The AT91 MCI has special SDIO transfer types: SDIO block and SDIO byte
transfers, but at91_mci driver doesn't use them and handles all SDIO
transfers as ordinary MMC block transfers. This causes problems for
multiple-block SDIO transfers (in particular for 256-bytes blocks).
Fix this situation by checking the opcode for SDIO CMD53 and setting
the transfer type in the AT91_MCI_CMDR register properly.
This patch was tested with libertas SDIO driver: problem with TX
timeouts on big packets was eliminated.
Signed-off-by: Yauhen Kharuzhy <yauhen.kharuzhy@promwad.com>
Cc: <stable@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds nanoEngine's PCI support.
Signed-off-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds nanoEngine PCMCIA support, with support for two sockets.
In order to have a fully functional pcmcia subsystem in a BSE
nanoEngine board you should carefully read this:
http://cambuca.ldhs.cetuc.puc-rio.br/nanoengine/
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes checkpatch.pl issues in
arch/arm/mach-sa1100/cpu-sa1110.c.
Signed-off-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adds Bright Star Engineering's nanoEngine board support to the kernel.
Also:
- Adds the nanoEngine memory chip to arch/arm/mach-sa1100/cpu-sa1110.c
(Micron MT48LC8M16A2TG-75).
- Increase in the sdram_params->name[] field length to accomodate the
name of the memory chip.
- Clean up of header content and order of
arch/arm/mach-sa1100/cpu-sa1110.c
Signed-off-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If the TPA6130 is compiled as module the id and power_gpio values are
arbitrary at module probing time since the rx51_tpa6130a2_data was marked as
__initdata. Fix this by using __initdata_or_module. Then __initdata is
defined only if the kernel is built without CONFIG_MODULES and omitted
otherwise.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
After commit ed919b0 "mmc: sdio: fix runtime PM anomalies by introducing
MMC_CAP_POWER_OFF_CARD" it is required to specify MMC_CAP_POWER_OFF_CARD
to have runtime PM support. As the wl1251 driver expects card to be
powered down when it's not used, wifi will no longer work after interface
is brought down at least once without functioning runtime PM.
Fix this by declaring MMC_CAP_POWER_OFF_CARD for MMC3.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds omap_reserve functionality to board-omap4panda.c.
Helps in the reserving boot time memory in SDRAM, used here for
framebuffer allocation.
This patch is in similar lines to commit id 71ee7dad9b, from
Russell king
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Raghuveer Murthy <raghuveer.murthy@ti.com>
[tony@atomide.com: fixed to be before .map_io as pointed out by Russell King]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Register BH1780GLI Ambient light sensor, which is an I2C device
for 4430SDP board.
Signed-off-by: Hemanth V <hemanthv@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make sure the LED is turned off at boot time, and configure the GPIO LED
device as active low.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
gpio_direction_output() has a value argument, there's no need to call
gpio_set_value() explicitly right after.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
No need to call this early from init_irq. Also recent changes
initialize GPIO now later, so calling gpio_request from init_irq
will make it fail.
While at it, also remove the unnecessary EXPORT_SYMBOL.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 72f381ba05 (omap3: Remove VMMC2 regulator on IGEP v2)
removed an unused regulator entry, but left the second MMC channel
(used by the Libertas WLAN module) without link to power regulator.
This causes the SDIO module to fail being detected.
This patch adds the two regulators that actually feed the WLAN module
(1v8 from the TWL4030 VIO LDO, and a fixed 3v3). With that patch, the
second channel is properly detected. Details of the power supply
implementation were kindly provided by Enric Balletbo i Serra.
Also change vmmc1 to use symbolic names instead of direct device
reference.
Tested on an IGEPv2 Rev-B.
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Patch "OMAP2xxx: hwmod: add I2C hwmods for OMAP2420, 2430"
in linux-next as of 20101203 introduced the following build
warning - fix this by removing the stray i2c_dev_attr.
arch/arm/mach-omap2/omap_hwmod_2430_data.c:483: warning: 'i2c_dev_attr' defined but not used
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
To support tvout on rx51,added Intilization data,
tvout as display device and enabled venc through gpio
on rx51
Signed-off-by: Srikar <ext-srikar.1.bhavanarayana@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Upcoming ASoC core and tlv320aic3x changes makes possible to take b part of
TLV320AIC34 into use on RX51/N900. Prepare to this by adding virtual supplies
and platform data for b part of the codec.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove second tlv320aic3x.h inclusion that came along the commit f0fba2a
"ASoC: multi-component - ASoC Multi-Component Support".
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is no MFD config option, MFD_SUPPORT should be selected instead.
This will prevent build errors when trying out different configurations.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
clk_get() return value should be checked with IS_ERR(). Furthermore,
clocks should be put and disabled properly.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert DMA library into DMA platform driver and make use of
platform data provided by hwmod data base for OMAP2+ onwards.
For OMAP1 processors, the DMA driver in mach-omap uses resource
structures for getting platform data.
Thanks to Tony Lindgren <tony@atomide.com> for fixing various
omap1 issues and testing the same on OSK5912 board.
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Prepare OMAP2+ DMA to use hwmod infrastructure so that DMA can register
as platform device.
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Implement OMAP1 DMA as platform device and add support for
registering through platform device layer using resource
structures.
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add OMAP4 DMA hwmod data. In addition to original dma hwmod data,
the following changes are added.
1. DMA device attributes structure is introduced for diffenrenciating
OMAP cpu's based on DMA features.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add OMAP2430 DMA hwmod data and also add required
DMA device attributes.
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add OMAP2420 DMA hwmod data and also add required
DMA device attributes.
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Implement errata handling to use flags instead of cpu_is_* and
cpu_class_* in the code.
The errata flags are initialized at init time and during runtime we are
using the errata variable (via the IS_DMA_ERRATA macro) to execute the
required errata workaround.
Reused errata handling patch from: Peter Ujfalusi
<peter.ujfalusi@nokia.com>
https://patchwork.kernel.org/patch/231191/
Changes to above patch:
1. Changes are done for converting all the existing errata work arounds
to use this feature.
2. Detailed description for each errata is added.
3. Fixed bug in SET_DMA_ERRATA macro
4. Bit shifting in macro definitions are replaced with BIT() macro
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Prepare DMA library to get converted into DMA driver using platform
device model and hwmod infrastucture(for omap2+, resource structures
for omap1)
The low level read/write macros are replaced with static inline
functions and register offsets are handled through static register
offset tables mapped through enumeration constants.
These low level read/write functions along with static register offset
tables will be moved to respective mach-omap dma files in the later
patches of this series.
There are no functionality changes with these changes except change in
logic for handling 16bit registers of OMAP1.
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The convention for omap device naming is omap_XXX.
Rename the device and driver name in order to stick
to this naming convention.
Change device name in clock nodes as well.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Ben Dooks <ben-i2c@fluff.org>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix following compilation warning:
arch/arm/mach-omap1/pm_bus.c: In function 'omap1_pm_runtime_resume':
arch/arm/mach-omap1/pm_bus.c:51: warning: unused variable 'ret'
Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Patch fix following compilation warning:
arch/arm/mach-omap1/board-htcherald.c:442:
warning: large integer implicitly truncated to unsigned type
Hopefully this is just a typo.
Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The naming convention for omap_device is omap_XXX.
Rename the device and driver name in order to stick
to this naming convention.
Remove the hs prefix that is implicit for every OMAP uarts.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Govindraj Raja <govindraj.raja@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* msm-core: (28 commits)
msm: initial framebuffer support
msm: add handling for clocks tagged as CLK_MINMAX
msm: trout: change name of pmdh_clk to mddi_clk
msm: add CLK_MINMAX to pmdh_clk
msm: trout: add gpio_to_irq
msm: iommu: Use the correct memory allocation flag
msm_serial: Remove redundant unlikely()
msm: iommu: Miscellaneous code cleanup
msm: iommu: Support cache-coherent memory access
msm: iommu: Definitions for extended memory attributes
msm: iommu: Kconfig dependency for the IOMMU API
msm: iommu: Check if device is already attached
msm: iommu: Kconfig item for cacheable page tables
msm: iommu: Don't flush page tables if no devices attached
msm: iommu: Mark functions with the right section names
msm: iommu: Support for the 2nd GFX core's IOMMU
msm: iommu: Revise GFX2D0 IOMMU contexts and M2V mappings
msm: iommu: Revise GFX3D IOMMU contexts and M2V mappings
msm: iommu: Use more consistent naming in platform data
msm: iomap: Addresses and IRQs for 2nd GFX core IOMMU
...
* msm-mmc: (33 commits)
mmc: msm_sdcc: Check for only DATA_END interrupt to end a request
mmc: msm_sdcc: Fix bug in PIO mode when data size is not word aligned
mmc: msm_sdcc: Reset SDCC in case of data transfer errors
mmc: msm_sdcc: Add prog done interrupt support
mmc: msm_sdcc: Fix possible circular locking dependency warning
msm: initial framebuffer support
msm: add handling for clocks tagged as CLK_MINMAX
msm: trout: change name of pmdh_clk to mddi_clk
msm: add CLK_MINMAX to pmdh_clk
msm: trout: add gpio_to_irq
msm: iommu: Use the correct memory allocation flag
msm_serial: Remove redundant unlikely()
msm: iommu: Miscellaneous code cleanup
msm: iommu: Support cache-coherent memory access
msm: iommu: Definitions for extended memory attributes
msm: iommu: Kconfig dependency for the IOMMU API
msm: iommu: Check if device is already attached
msm: iommu: Kconfig item for cacheable page tables
msm: iommu: Don't flush page tables if no devices attached
msm: iommu: Mark functions with the right section names
...
* 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S5PV210: update MAX8998 platform data to get rid of WARN()
ARM S3C24XX: Fix compilation of PM code for S3C2416
ARM: S3C24XX: Fix CONFIG_S3C_DEV_NAND Kconfig entry
The cnt32_to_63 algorithm relies on proper counter data evaluation
ordering to work properly. This was missing from the provided
documentation.
Let's augment the documentation with the missing usage constraint and
fix the only instance that got it wrong.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When we soft-CPU hotplug a CPU, we reset the stack pointer and
jump back to start_secondary(). This allows us to restart as if
the CPU was actually reset.
However, we weren't resetting the frame pointer, which could cause
problems with backtracing. Reset the frame pointer to zero (which
means no parent frame) just like the early assembly code also does.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There are 2 versions of the timrot on Freescale MXS-based SoCs.
The v1 on MX23 only gets 16 bits counter, while v2 on MX28
extends the counter to 32 bits.
The implementation uses two timers, one for clock_event and
another for clocksource. MX28 uses timrot 0 and 1, while MX23
uses 0 and 2.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
- DEBUG_LL support, which is incompatible with multi-soc MXS image
because of different DUART base address on MX23 and MX28
- uncompress message support
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Increase NR_IRQS from 512 to 1024 on SH-Mobile ARM.
Needed to support vectors in the sh73a0 INTCS block.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use PAGE_OFFSET and PHYS_OFFSET for secondary_startup
entry point as recommended by Russell King.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The new FPGA firmware in Balloon3 uses different methods to control it's bus
control lines. In the new version, there are separate registers to set/clear
bus control lines. This patch updates affected places.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
smp.c is becoming too large, so split out the TLB maintainence
broadcasting into a separate smp_tlb.c file.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When a CPU is hot unplugged, the generic tick code cleans up the
clock event device, but fails to call down to the device's set_mode
function to actually shut the device down.
To work around this, we've historically had a local_timer_stop()
callback out of the hotplug code. However, this adds needless
complexity when we have the clock event device itself available.
Explicitly call the clock event device's set_mode function with
CLOCK_EVT_MODE_UNUSED, so that the hardware can be cleanly shutdown
without any special external callbacks. When/if the generic code
is fixed, percpu_timer_stop() can be killed off.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The original scheme for reporting spurious wakeups was broken - it
tried to use printk() from a context which wasn't coherent with the
other CPUs, which risks corrupting the printk() data.
Fix this by noting the number spurious wakeups, and only report them
when we are properly woken - when we will be coherent with the rest
of the system.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We used to print a bland error message which gave no clue as to the
failure when we failed to bring up a secondary CPU. Resolve this by
separating the two failure cases.
If boot_secondary() fails, we print a message indicating the returned
error code from boot_secondary():
"CPU%u: failed to boot: %d\n", cpu, ret.
However, if boot_secondary() succeeded, but the CPU did not appear to
mark itself online within the timeout, indicate that it failed to come
online:
"CPU%u: failed to come online\n", cpu
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We can not guarantee that VFP will be enabled when CPU hotplug brings
a CPU back online from a reset state. Add a hotplug CPU notifier to
ensure that the VFP coprocessor access is enabled whenever a CPU comes
back online.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is a subtle race in the CPU hotplug code, where a CPU which has
been offlined can online itself before being requested, which results
in things going astray on the next online/offline cycle.
What happens in the normal online/offline/online cycle is:
CPU0 CPU3
requests boot of CPU3
pen_release = 3
flush cache line
checks pen_release, reads 3
starts boot
pen_release = -1
... requests CPU3 offline ...
... dies ...
checks pen_release, reads -1
requests boot of CPU3
pen_release = 3
flush cache line
checks pen_release, reads 3
starts boot
pen_release = -1
However, as the write of -1 of pen_release is not fully flushed back to
memory, and the checking of pen_release is done with caches disabled,
this allows CPU3 the opportunity to read the old value of pen_release:
CPU0 CPU3
requests boot of CPU3
pen_release = 3
flush cache line
checks pen_release, reads 3
starts boot
pen_release = -1
... requests CPU3 offline ...
... dies ...
checks pen_release, reads 3
starts boot
pen_release = -1
requests boot of CPU3
pen_release = 3
flush cache line
Fix this by grouping the write of pen_release along with its cache line
flushing code to ensure that any update to pen_release is always pushed
out to physical memory.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* __fixup_smp_on_up has been modified with support for the
THUMB2_KERNEL case. For THUMB2_KERNEL only, fixups are split
into halfwords in case of misalignment, since we can't rely on
unaligned accesses working before turning the MMU on.
No attempt is made to optimise the aligned case, since the
number of fixups is typically small, and it seems best to keep
the code as simple as possible.
* Add a rotate in the fixup_smp code in order to support
CPU_BIG_ENDIAN, as suggested by Nicolas Pitre.
* Add an assembly-time sanity-check to ALT_UP() to ensure that
the content really is the right size (4 bytes).
(No check is done for ALT_SMP(). Possibly, this could be fixed
by splitting the two uses ot ALT_SMP() (ALT_SMP...SMP_UP versus
ALT_SMP...SMP_UP_B) into two macros. In the first case,
ALT_SMP needs to expand to >= 4 bytes, not == 4.)
* smp_mpidr.h (which implements ALT_SMP()/ALT_UP() manually due
to macro limitations) has not been modified: the affected
instruction (mov) has no 16-bit encoding, so the correct
instruction size is satisfied in this case.
* A "mode" parameter has been added to smp_dmb:
smp_dmb arm @ assumes 4-byte instructions (for ARM code, e.g. kuser)
smp_dmb @ uses W() to ensure 4-byte instructions for ALT_SMP()
This avoids assembly failures due to use of W() inside smp_dmb,
when assembling pure-ARM code in the vectors page.
There might be a better way to achieve this.
* Kconfig: make SMP_ON_UP depend on
(!THUMB2_KERNEL || !BIG_ENDIAN) i.e., THUMB2_KERNEL is now
supported, but only if !BIG_ENDIAN (The fixup code for Thumb-2
currently assumes little-endian order.)
Tested using a single generic realview kernel on:
ARM RealView PB-A8 (CONFIG_THUMB2_KERNEL={n,y})
ARM RealView PBX-A9 (SMP)
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With "ARM: CPU hotplug: remove bug checks in platform_cpu_die()", we
now do not use hard_smp_processor_id(), we no longer need to read the
hardware processor ID. Remove the include providing this function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Don't call idle_task_exit() with interrupts disabled, and ensure
that we have a memory barrier after interrupts are disabled but
before signalling that this CPU has shut down.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
platform_cpu_die() is entered from the CPU's own idle thread, which
can not be migrated to other CPUs. Moreover, the 'cpu' argument
comes from the thread info, which will always be the 'current'
CPU. So remove this useless bug check.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We always need to wait for the dying CPU to reach a safe state before
taking it down, irrespective of the requirements of the platform.
Move the completion code into the ARM SMP hotplug code rather than
having each platform re-implement this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
All platforms call trace_hardirqs_off() in their secondary startup code,
so move this into the core SMP code - it doesn't need to be in the
per-platform code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is a certain amount of smp_prepare_cpus() which doesn't belong
in the platform support code - that is, code which is invariant to the
SMP implementation. Move this code into arch/arm/kernel/smp.c, and
add a platform_ prefix to the original function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Milo is an old boot loader, which is no longer relevant for these
platforms. References to it are misleading. Move the code out
of poke_milo(), and remove references to milo in comments.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
scu_get_core_count() never returns zero cores, so we don't need to
check and correct if ncores is zero.
Tegra was missing the check against NR_CPUS, leading to a potential
bitfield overflow if this becomes the case.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure that the number of CPUs is sanity checked before setting
the number of possible CPUs. This avoids any chance of overflowing
the cpu_possible bitmap.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Wait for CPUs to indicate that they've stopped, after sending the
stop IPI, rather than blindly continuing on and hoping that they've
stopped in time. Print a warning if we fail to stop the other CPUs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use r0,r3-r6 rather than r0,r3,r4,r6,r7, which makes it easier to
understand which registers can be modified. Also document which
registers hold values which must be preserved.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The IPI and local timer interrupts weren't being properly accounted
for in /proc/stat. Collect them from the irq_stat structure, and
return their sum.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This separates out the individual IPI interrupt counts from the
total IPI count, which allows better visibility of what IPIs are
being used for.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested on a Colibri Evaluation Board Rev.2.1 with a Colibri PXA310 module.
Signed-off-by: Bjorn Forsman <bjorn.forsman@gmail.com>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Mark F. Brown <mark.brown314@gmail.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Rename colibri-pxa270-evalboard to colibri-evalboard as this board is used with
all Colibri modules.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This change -- pushing the MFP configuration back into Module files -- is
necessary because some evalboards can be used with multiple modules, where MFP
differs from module to module. Therefore MFP isn't board-specific, but
module-specific and the module should preconfigure itself for the board.
(And there is also the C preprocesor limitation and conflicting #define-s)
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This driver also contains structures to eventually support PXA320. This is
planned to be added in a later patch.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
iwmmxt is used in XScale, XScale3, Mohawk and PJ4 core. But the instructions
of accessing CP0 and CP1 is changed in PJ4. Append more files to support
iwmmxt in PJ4 core.
Signed-off-by: Zhou Zhu <zzhu3@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
As per x86, align the initial column according to how many IRQs we
have. Also, provide an english explaination for the 'LOC:' and
'IPI:' lines.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the ipi_count into irq_stat, which allows the ipi_data structure
to be entirely removed.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide __inc_irq_stat() and __get_irq_stat() to increment and
read the irq stat counters.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
send_ipi_message() does nothing except call smp_cross_call(). As
this is a static function, nothing external to this file calls it,
so we can easily clean up this now unnecessary indirection.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- The mxs wdog is implemented in RTC block.
- There is a generic software reset routine for most modules on mxs.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Move keylayouts to a dedicated file and plug these keylayouts
for input platform data. This will make addition of new and custom
keylayouts localized.
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-32: Make sure we can map all of lowmem if we need to
x86, vt-d: Handle previous faults after enabling fault handling
x86: Enable the intr-remap fault handling after local APIC setup
x86, vt-d: Fix the vt-d fault handling irq migration in the x2apic mode
x86, vt-d: Quirk for masking vtd spec errors to platform error handling logic
x86, xsave: Use alloc_bootmem_align() instead of alloc_bootmem()
bootmem: Add alloc_bootmem_align()
x86, gcc-4.6: Use gcc -m options when building vdso
x86: HPET: Chose a paranoid safe value for the ETIME check
x86: io_apic: Avoid unused variable warning when CONFIG_GENERIC_PENDING_IRQ=n
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf: Fix off by one in perf_swevent_init()
perf: Fix duplicate events with multiple-pmu vs software events
ftrace: Have recordmcount honor endianness in fn_ELF_R_INFO
scripts/tags.sh: Add magic for trace-events
tracing: Fix panic when lseek() called on "trace" opened for writing
Add block identifier to be able to add multiple mfd clients
to the mfd core
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Most of the register layout, client IRQ numbers on the TC35892 is shared also
by other variants. Make this generic as tc3589x
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Since commit 3e4d3af501 "mm: stack based kmap_atomic()", it is actively
wrong to rely on fixed kmap type indices (namely KM_L2_CACHE) as
kmap_atomic() totally ignores them and a concurrent instance of it may
happily reuse any slot for any purpose. Because kmap_atomic() is now
able to deal with reentrancy, we can get rid of the ad hoc mapping here.
While the code is made much simpler, there is a needless cache flush
introduced by the usage of __kunmap_atomic(). It is not clear if the
performance difference to remove that is worth the cost in code
maintenance (I don't think there are that many highmem users on that
platform anyway) but that should be reconsidered when/if someone cares
enough to do some measurements.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Since commit 3e4d3af501 "mm: stack based kmap_atomic()", it is actively
wrong to rely on fixed kmap type indices (namely KM_L2_CACHE) as
kmap_atomic() totally ignores them and a concurrent instance of it may
happily reuse any slot for any purpose. Because kmap_atomic() is now
able to deal with reentrancy, we can get rid of the ad hoc mapping here,
and we even don't have to disable IRQs anymore (highmem case).
While the code is made much simpler, there is a needless cache flush
introduced by the usage of __kunmap_atomic(). It is not clear if the
performance difference to remove that is worth the cost in code
maintenance (I don't think there are that many highmem users on that
platform if at all anyway).
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Since commit 3e4d3af501 "mm: stack based kmap_atomic()", it is no longer
necessary to carry an ad hoc version of kmap_atomic() added in commit
7e5a69e83b "ARM: 6007/1: fix highmem with VIPT cache and DMA" to cope
with reentrancy.
In fact, it is now actively wrong to rely on fixed kmap type indices
(namely KM_L1_CACHE) as kmap_atomic() totally ignores them now and a
concurrent instance of it may reuse any slot for any purpose.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure that no interrupt is pending before registering the clock
event device, and properly initialize the periodic tick in the
->set_mode callback.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for up to 6 hardware counters for AMD family
15h cpus. There is a new MSR range for hardware counters beginning at
MSRC001_0200 Performance Event Select (PERF_CTL0).
Signed-off-by: Robert Richter <robert.richter@amd.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch/tile: handle rt_sigreturn() more cleanly
arch/tile: handle CLONE_SETTLS in copy_thread(), not user space
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
x86: avoid high BIOS area when allocating address space
x86: avoid E820 regions when allocating address space
x86: avoid low BIOS area when allocating address space
resources: add arch hook for preventing allocation in reserved areas
Revert "resources: support allocating space within a region from the top down"
Revert "PCI: allocate bus resources from the top down"
Revert "x86/PCI: allocate space from the end of a region, not the beginning"
Revert "x86: allocate space within a region top-down"
Revert "PCI: fix pci_bus_alloc_resource() hang, prefer positive decode"
PCI: Update MCP55 quirk to not affect non HyperTransport variants
The AXI protocol specifies that the write response can only
be sent back to an AXI master when the last write data has been
accepted. This optimization enables the PL310 to send the write
response of certain write transactions as soon as the store buffer
accepts the write address. This behavior is not compatible with
the AXI protocol and is disabled by default. You enable this
optimization by setting the Early BRESP Enable bit in the
Auxiliary Control Register (bit [30]).
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Clearing bit 22 in the PL310 Auxiliary Control register (shared
attribute override enable) has the side effect of transforming Normal
Shared Non-cacheable reads into Cacheable no-allocate reads.
Coherent DMA buffers in Linux always have a Cacheable alias via the
kernel linear mapping and the processor can speculatively load cache
lines into the PL310 controller. With bit 22 cleared, Non-cacheable
reads would unexpectedly hit such cache lines leading to buffer
corruption
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enabling L2 prefetching improves performance as shown on Panda
ES2.1 board with mem test, and it has measurable impact on
performances. I think we should consider it, even though it damages
"writes" a bit. (rebased to k.org)
Usually the prefetch is used at both levels together L1 + L2, however,
to enable the CP15 prefetch engines, these are under security, and on
GP devices, we cannot enable it(e.g. on PandaBoard). However, just
enabling PL310 prefetch seems to provide performance improvement,
as shown in the data below (from Ubuntu) and would be a great thing
to pull in.
What prefetch does is enable automatic next line prefetching. With this
enabled, whenever the PL310 receives a cachable read request, it
automatically prefetches the following cache line as well.
Measurement Data:
==
STOCK 10.10 WITHOUT PATCH
========================
~# ./memspeed
size 8388608 8192k 8M
offset 8388608, 0
buffers 0x2aaad000 0x2b2ad000
copy libc 133 MB/s
copy Android v5 273 MB/s
copy Android NEON 235 MB/s
copy INT32 116 MB/s
copy ASM ARM 187 MB/s
copy ASM VLDM 64 204 MB/s
copy ASM VLDM 128 173 MB/s
copy ASM VLD1 216 MB/s
read ASM ARM 286 MB/s
read ASM VLDM 242 MB/s
read ASM VLD1 286 MB/s
write libc 1947 MB/s
write ASM ARM 1943 MB/s
write ASM VSTM 1942 MB/s
write ASM VST1 1935 MB/s
10.10 + PATCH
=============
~# ./memspeed
size 8388608 8192k 8M
offset 8388608, 0
buffers 0x2ab17000 0x2b317000
copy libc 129 MB/s
copy Android v5 256 MB/s
copy Android NEON 356 MB/s
copy INT32 127 MB/s
copy ASM ARM 321 MB/s
copy ASM VLDM 64 337 MB/s
copy ASM VLDM 128 321 MB/s
copy ASM VLD1 350 MB/s
read ASM ARM 496 MB/s
read ASM VLDM 470 MB/s
read ASM VLD1 488 MB/s
write libc 1701 MB/s
write ASM ARM 1682 MB/s
write ASM VSTM 1693 MB/s
write ASM VST1 1681 MB/s
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch removes the hardcoded value of auxctrl value and
construct it using bitfields
Bit 25 is reserved and is always set to 1. Same value
of this bit is retained in this patch
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds the PL310 Auxiliary Control Register bitfields
so that SOC's can use these bit fields to construct the AUXCTRL
value to be passed/programmed instead of hardcoding it.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use cmpxchg instead of xchg to realize this_cpu_xchg.
xchg will cause LOCK overhead since LOCK is always implied but cmpxchg
will not.
Baselines:
xchg() = 18 cycles (no segment prefix, LOCK semantics)
__this_cpu_xchg = 1 cycle
(simulated using this_cpu_read/write, two prefixes. Looks like the
cpu can use loop optimization to get rid of most of the overhead)
Cycles before:
this_cpu_xchg = 37 cycles (segment prefix and LOCK (implied by xchg))
After:
this_cpu_xchg = 11 cycle (using cmpxchg without lock semantics)
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Provide support as far as the hardware capabilities of the x86 cpus
allow.
Define CONFIG_CMPXCHG_LOCAL in Kconfig.cpu to allow core code to test for
fast cpuops implementations.
V1->V2:
- Take out the definition for this_cpu_cmpxchg_8 and move it into
a separate patch.
tj: - Reordered ops to better follow this_cpu_* organization.
- Renamed macro temp variables similar to their existing
neighbours.
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
We should not be incrementing mm_users when we startup a secondary
CPU - doing so results in mm_users incrementing by one each time we
hotplug a CPU, which will eventually wrap, and will cause problems.
Other architectures such as x86 do not increment mm_users, but only
mm_count, so we follow that pattern.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since CPU_PJ4 is shared between PXA95x and MMP2, select CPU_PJ4 in MMP2
configuration.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Saarb platform is a handheld platform that supports Marvell PXA955 silicon.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The core of PXA955 is PJ4. Add new PJ4 support. And add new macro
CONFIG_PXA95x.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Commit f2ce623126 (OMAP: WDT: Split OMAP1 and OMAP2PLUS device
registration) removed omap_init_wdt and related structures from
plat-omap/devices.c. However a subsequent commit or merge
seems to have reintroduced these by accident. The caller of
omap_init_wdt was also removed by that commit, and this did
not get restored. So we have the following build warning now:
CC arch/arm/plat-omap/devices.o
arch/arm/plat-omap/devices.c:252: warning: 'omap_init_wdt' defined but not used
Fix this by removing this dead code.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
New assemblers need -march=armv7-a+sec on command line or
.arch_extension sec inline to enable use of the smc instruction.
This patch uses as-instr to check the latter to conditionally
enable the former in AFLAGS for files that use smc.
Checked on both old and new binutils to verify that it does
not break old versions.
Signed-off-by: John Rigby <john.rigby@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch will kill following section mismatch warnings:
WARNING: vmlinux.o(.text+0x24a00): Section mismatch in reference from the function zoom_twl_gpio_setup() to the (unknown reference) .init.data:(unknown)
The function zoom_twl_gpio_setup() references
the (unknown reference) __initdata (unknown).
This is often because zoom_twl_gpio_setup lacks a __initdata
annotation or the annotation of (unknown) is wrong.
WARNING: vmlinux.o(.text+0x24bfc): Section mismatch in reference from the function cm_t35_twl_gpio_setup() to the (unknown reference) .init.data:(unknown)
The function cm_t35_twl_gpio_setup() references
the (unknown reference) __initdata (unknown).
This is often because cm_t35_twl_gpio_setup lacks a __initdata
annotation or the annotation of (unknown) is wrong.
WARNING: vmlinux.o(.data+0x1d3e0): Section mismatch in reference from the variable h4_config to the (unknown reference) .init.data:(unknown)
The variable h4_config references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: vmlinux.o(.data+0x1dc08): Section mismatch in reference from the variable sdp2430_config to the (unknown reference) .init.data:(unknown)
The variable sdp2430_config references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: vmlinux.o(.data+0x1e1d8): Section mismatch in reference from the variable apollon_config to the (unknown reference) .init.data:(unknown)
The variable apollon_config references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Power to the wl12xx wlan device is controlled by a fixed regulator.
Boards that have the wl12xx should select REGULATOR_FIXED_VOLTAGE so
users will not be baffled.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add comments and IDs for the following erratas:
- i540: MPU cannot exit from Standby,
- i478: Unexpected Cold-Reset is generated when device is coming
back from OFF mode
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add minimal support for Nokia RM-680 board.
Tested with omap2plus_defconfig.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
[tony@atomide.com: updated to remove omap_gpio_init
Signed-off-by: Tony Lindgren <tony@atomide.com>
Introduce 97.6/195.2 MHz memory timing data. Based on patches by Eduardo
Valentin, Igor Dmitriev and Juha Keski-Saari.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Cc: Eduardo Valentin <eduardo.valentin@nokia.com>
Cc: Igor Dmitriev <ext-dmitriev.igor@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Actually check for errors: print an error log and return NULL.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use an array to make it easier to add new values.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rename the current timings to indicate they're for 166 MHz. Based on
patches by Eduardo Valentin and Juha Keski-Saari.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Cc: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a header file for Nokia SDRAM functions. Based on patches by Juha
Keski-Saari.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rename the file and functions so that it can be reused by future Nokia
boards. Based on patches by Juha Keski-Saari.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Keep the crash kernel address below 512 MiB for 32 bits and 896 MiB
for 64 bits. For 32 bits, this retains compatibility with earlier
kernel releases, and makes it work even if the vmalloc= setting is
adjusted.
For 64 bits, we should be able to increase this substantially once a
hard-coded limit in kexec-tools is fixed.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <20101217195035.GE14502@redhat.com>
The current tile rt_sigreturn() syscall pattern uses the common idiom
of loading up pt_regs with all the saved registers from the time of
the signal, then anticipating the fact that we will clobber the ABI
"return value" register (r0) as we return from the syscall by setting
the rt_sigreturn return value to whatever random value was in the pt_regs
for r0.
However, this breaks in our 64-bit kernel when running "compat" tasks,
since we always sign-extend the "return value" register to properly
handle returned pointers that are in the upper 2GB of the 32-bit compat
address space. Doing this to the sigreturn path then causes occasional
random corruption of the 64-bit r0 register.
Instead, we stop doing the crazy "load the return-value register"
hack in sigreturn. We already have some sigreturn-specific assembly
code that we use to pass the pt_regs pointer to C code. We extend that
code to also set the link register to point to a spot a few instructions
after the usual syscall return address so we don't clobber the saved r0.
Now it no longer matters what the rt_sigreturn syscall returns, and the
pt_regs structure can be cleanly and completely reloaded.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Previously we were just setting up the "tp" register in the
new task as started by clone() in libc. However, this is not
quite right, since in principle a signal might be delivered to
the new task before it had its TLS set up. (Of course, this race
window still exists for resetting the libc getpid() cached value
in the new task, in principle. But in any case, we are now doing
this exactly the way all other architectures do it.)
This change is important for 2.6.37 since the tile glibc we will
be submitting upstream will not set TLS in user space any more,
so it will only work on a kernel that has this fix. It should
also be taken for 2.6.36.x in the stable tree if possible.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Cc: stable <stable@kernel.org>
Seen with malta_defconfig on Linus' tree:
CC arch/mips/mm/sc-mips.o
arch/mips/mm/sc-mips.c: In function 'mips_sc_is_activated':
arch/mips/mm/sc-mips.c:77: error: 'config2' undeclared (first use in this function)
arch/mips/mm/sc-mips.c:77: error: (Each undeclared identifier is reported only once
arch/mips/mm/sc-mips.c:77: error: for each function it appears in.)
arch/mips/mm/sc-mips.c:81: error: 'tmp' undeclared (first use in this function)
make[2]: *** [arch/mips/mm/sc-mips.o] Error 1
make[1]: *** [arch/mips/mm] Error 2
make: *** [arch/mips] Error 2
[Ralf: Cosmetic changes to minimize the number of arguments passed to
mips_sc_is_activated]
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/1752/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This prevents allocation of the last 2MB before 4GB.
The experiment described here shows Windows 7 ignoring the last 1MB:
https://bugzilla.kernel.org/show_bug.cgi?id=23542#c27
This patch ignores the top 2MB instead of just 1MB because H. Peter Anvin
says "There will be ROM at the top of the 32-bit address space; it's a fact
of the architecture, and on at least older systems it was common to have a
shadow 1 MiB below."
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When we allocate address space, e.g., to assign it to a PCI device, don't
allocate anything mentioned in the BIOS E820 memory map.
On recent machines (2008 and newer), we assign PCI resources from the
windows described by the ACPI PCI host bridge _CRS. On many Dell
machines, these windows overlap some E820 reserved areas, e.g.,
BIOS-e820: 00000000bfe4dc00 - 00000000c0000000 (reserved)
pci_root PNP0A03:00: host bridge window [mem 0xbff00000-0xdfffffff]
If we put devices at 0xbff00000, they don't work, probably because
that's really RAM, not I/O memory. This patch prevents that by removing
the 0xbfe4dc00-0xbfffffff area from the "available" resource.
I'm not very happy with this solution because Windows solves the problem
differently (it seems to ignore E820 reserved areas and it allocates
top-down instead of bottom-up; details at comment 45 of the bugzilla
below). That means we're vulnerable to BIOS defects that Windows would not
trip over. For example, if BIOS described a device in ACPI but didn't
mention it in E820, Windows would work fine but Linux would fail.
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=16228
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This implements arch_remove_reservations() so allocate_resource() can
avoid any arch-specific reserved areas. This currently just avoids the
BIOS area (the first 1MB), but could be used for E820 reserved areas if
that turns out to be necessary.
We previously avoided this area in pcibios_align_resource(). This patch
moves the test from that PCI-specific path to a generic path, so *all*
resource allocations will avoid this area.
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'for_linus' of git://github.com/at91linux/linux-2.6-at91:
at91: Refactor Stamp9G20 and PControl G20 board file
at91: Fix uhpck clock rate in upll case
* 'kvm-updates/2.6.37' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: Fix preemption counter leak in kvm_timer_init()
KVM: enlarge number of possible CPUID leaves
KVM: SVM: Do not report xsave in supported cpuid
KVM: Fix OSXSAVE after migration
- include/linux/percpu.h: this_cpu_add_return() and friends were
located next to __this_cpu_add_return(). However, the overall
organization is to first group by preemption safeness. Relocate
this_cpu_add_return() and friends to preemption-safe area.
- arch/x86/include/asm/percpu.h: Relocate percpu_add_return_op() after
other more basic operations. Relocate [__]this_cpu_add_return_8()
so that they're first grouped by preemption safeness.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Christoph Lameter <cl@linux.com>
Supply an implementation for x86 in order to generate more efficient code.
V2->V3:
- Cleanup
- Remove strange type checking from percpu_add_return_op.
tj: - Dropped unused typedef from percpu_add_return_op().
- Renamed ret__ to paro_ret__ in percpu_add_return_op().
- Minor indentation adjustments.
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Use this_cpu_ops to reduce code size and simplify things in various places.
V3->V4:
Move instance of this_cpu_inc_return to a later patchset so that
this patch can be applied without infrastructure changes.
Cc: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Use this_cpu ops in various places to optimize per cpu data access.
Cc: Jason Baron <jbaron@redhat.com>
Cc: Namhyung Kim <namhyung@gmail.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
As PControl G20 is a carrier board for the Stamp9G20 SoM, some code can
be shared. Therefore board-stamp9g20.c is refactored to allow reusing the
SoM initialization and board-pcontrol-g20.c is modified to use it.
Signed-off-by: Christian Glindkamp <christian.glindkamp@taskit.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The uhpck clock should be divided from the utmi clock, not its parent
(main). This change is mostly cosmetic as the uhpck rate value is not
used anywhere except for the debugfs clock output.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Fix interrupt priority level handling on SH-Mobile ARM.
SH-Mobile ARM platforms using multiple interrupt priority
levels need this patch to fix a potential dead lock that
may occur if multiple interrupts with different levels
are pending simultaneously.
The default INTC configuration is to use the same priority
level for all interrupts, so this issue does not trigger by
default. It is however common for board code to override the
interrupt priority for certain interrupt sources depending
on the application. Without this fix such boards may lock up.
In detail, this patch updates the INTC code in entry-macro.S
to make sure that the INTLVLA register gets set as expected.
To trigger this bug modify the board specific code to adjust
the interrupt priority level for the ethernet chip. After
changing the priority level simply use flood ping to drown
the board with interrupts.
This patch applies to INTCA-based processors such as sh7372,
sh7377 and sh7372. GIC-based processors are not affected.
Suitable for v2.6.37-rc and stable from v2.6.34 to v2.6.36.
Cc: stable@kernel.org
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Turn down the warning noise from the compiler,
basically a SH-Mobile specific version of the
patch located in the RMK patch tracker:
6484/1: "fix compile warning in mm/init.c",
Without this patch the following warning triggers:
CC arch/arm/kernel/sys_arm.o
arch/arm/mm/init.c: In function 'mem_init':
arch/arm/mm/init.c:606: warning: format '%08lx' expects type 'long unsigned int', but argument 12 has type 'unsigned int'
CC arch/arm/kernel/traps.o
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The on-board NMI switch is routed through and mangled by the FPGA prior
to its delivery to the NMI pin, so add some glue for the various
configuration options. The default is to unmask it and enable all input
sources.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds new entries required by the new version of MAX8998
driver. Without them, the driver fails to init. See commit 50f19a4596
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
S3C2416 PM code uses low-level sleep routines from S3C2412 code,
but these routines are compiled only for S3C2412 SoC.
Split S3C2412_PM to two parts: S3C2412_PM, S3C2412_PM_SLEEP and
select last in S3C2416's Kconfig.
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
A relocatable kernel can be anywhere in lowmem -- and in the case of a
kdump kernel, is likely to be fairly high. Since the early page
tables map everything from address zero up we need to make sure we
allocate enough brk that we can map all of lowmem if we need to.
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Tested-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4D0AD3ED.8070607@kernel.org>
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus: (28 commits)
MIPS: Add a CONFIG_FORCE_MAX_ZONEORDER Kconfig option.
MIPS: LD/SD o32 macro GAS fix update
MIPS: Alchemy: fix build with SERIAL_8250=n
MIPS: Rename mips_dma_cache_sync back to dma_cache_sync
MIPS: MT: Fix typo in comment.
SSB: Fix nvram_get on BCM47xx platform
MIPS: BCM47xx: Swap serial console if ttyS1 was specified.
MIPS: BCM47xx: Use sscanf for parsing mac address
MIPS: BCM47xx: Fill values for b43 into SSB sprom
MIPS: BCM47xx: Do not read config from CFE
MIPS: FDT size is a be32
MIPS: Fix CP0 COUNTER clockevent race
MIPS: Fix regression on BCM4710 processor detection
MIPS: JZ4740: Fix pcm device name
MIPS: Separate two consecutive loads in memset.S
MIPS: Send proper signal and siginfo on FP emulator faults.
MIPS: AR7: Fix loops per jiffies on TNETD7200 devices
MIPS: AR7: Fix double ar7_gpio_init declaration
MIPS: Rework GENERIC_HARDIRQS Kconfig.
MIPS: Alchemy: Add return value check for strict_strtoul()
...
Add USB OTG, peripheral and host devices. This patch also adds
usb_phy_clk which is required for resetting the PHY. VBUS power up
and shutdown routines depends on PMIC module. As PMIC driver is
unavailable, configure USB in peripheral only mode.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
OTG driver takes care of putting hardware into low power mode. Hence
make peripheral and host devices as children of OTG device and let
runtime PM takes care of notifying peripheral and host state to
OTG device. VBUS power up and shutdown routines are implemented by
modem processor. As RPC infrastructure is not available, configure
USB in peripheral only mode.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
For huge page support with base page size of 16K or 32K, we have to
increase the MAX_ORDER so that huge pages can be allocated.
[Ralf: I don't think a user should have to configure obscure constants like
this but for the time being this will have to suffice.]
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1685/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
I am about to commit:
http://sourceware.org/ml/binutils/2010-10/msg00033.html
that fixes a problem with the LD/SD macro currently implemented by GAS for
the o32 ABI in an inconsistent way. This is best illustrated with a
simple program, which I'm copying here from the message above for easier
reference:
$ cat ld.s
ld $5,32767($4)
ld $5,32768($4)
This gets assebled into the following output:
$ mips-linux-as -32 -mips3 -o ld.o ld.s
$ mips-linux-objdump -d ld.o
ld.o: file format elf32-tradbigmips
Disassembly of section .text:
00000000 <.text>:
0: dc857fff ld a1,32767(a0)
4: 3c010001 lui at,0x1
8: 00810821 addu at,a0,at
c: 8c258000 lw a1,-32768(at)
10: 8c268004 lw a2,-32764(at)
...
Oops!
The GAS fix makes the macro behave in a consistent way and pairs of LW/SW
instructions to be output as appropriate regardless of the size of the
offset associated with the address used. The machine instruction is still
available, but to reach it macros have to be disabled first. This has a
side effect of requiring the use of a machine-addressable memory operand.
As some platforms require 64-bit operations for accesses to some I/O
registers LD/SD instructions are used in a couple of places in Linux
regardless of the ABI selected. Here's a fix for some pieces of code
affected I've been able to track down. The fix should be backwards
compatible with all supported binutils releases in existence and can be
used as a reference for any other places or off-tree code. The use of the
"R" constraint guarantees a machine-addressable operand.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1680/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In commit 7d172bfe ("Alchemy: Add UART PM methods") I introduced
platform PM methods which call a function of the 8250 driver;
this patch works around link failures when the kernel is built
without 8250 support.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/1737/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some devices like the Netgear WGT634U are using ttyS1 for default console
output. We should switch to that console if it was given in the kernel_args
parameters.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/1848/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Instead of writing own function for parsing the mac address we now
use sscanf.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/1847/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fill the sprom with all available values from the nvram. Most of these
new values are needed for the b43 or b43legacy driver.
Parts of this patch have been in OpenWRT for a long time and were written
by Michael Buesch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/1846/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The config options read out here are not stored in CFE but only in NVRAM on
the devices. Remove reading from CFE and only access the NVRAM. Reading out
CFE does not harm but is useless here.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/1845/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Consider the following test case:
write_c0_compare(read_c0_count());
Even if the counter doesn't increment during execution, this might not
generate an interrupt until the counter wraps around. The CPU may
perform the comparison each time CP0 COUNT increments, not when CP0
COMPARE is written.
If mips_next_event() is called with a very small delta, and CP0 COUNT
increments during the calculation of "cnt += delta", it is possible
that CP0 COMPARE will be written with the current value of CP0 COUNT.
If this is detected, the function should return -ETIME, to indicate
that the interrupt might not have actually gotten scheduled.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1836/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
BCM4710 uses the BMIPS32 core (like BCM6345), not the MIPS 4Kc core as
was previously believed.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Tested-by: Alexandros C. Couloumbis <alex@ozo.com>
Patchwork: https://patchwork.linux-mips.org/patch/1837/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
partial_fixup is used in noreorder block.
Separating two consecutive loads can save one cycle on processors with
GPR intrelock and can fix load-use on processors that need a load delay slot.
Also do so for fwd_fixup.
[Ralf: Only R2000/R3000 class processors are lacking the the load-user
interlock and even some of those got it retrofitted. With R2000/R3000
being fairly uncommon these days the impact of this bug should be minor.]
Signed-off-by: Tony Wu <tung7970@gmail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1768/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We were unconditionally sending SIGBUS with an empty siginfo on FP
emulator faults. This differs from what happens when real floating
point hardware would get a fault.
For most faults we need to send SIGSEGV with the faulting address
filled in in the struct siginfo.
Reported-by: Camm Maguire <camm@maguirefamily.org>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Cc: Camm Maguire <camm@maguirefamily.org>
Patchwork: https://patchwork.linux-mips.org/patch/1727/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
TNETD7200 run their CPU clock faster than the default CPU clock we assume.
In order to have the correct loops per jiffies settings, initialize clocks right
before setting mips_hpt_frequency. As a side effect, we can no longer use
msleep in clocks.c which requires other parts of the kernel to be initialized,
so replace these with mdelay.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1749/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Recent changes to CONFIG_GENERIC_HARDIRQS have caused us to start getting:
warning: (SMP && SYS_SUPPORTS_SMP) selects IRQ_PER_CPU which has unmet direct dependencies (HAVE_GENERIC_HARDIRQS)
Rearranging our Kconfig quiets the message.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Patchwork: https://patchwork.linux-mips.org/patch/1757/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
cc1: warnings being treated as errors
arch/mips/loongson/common/env.c: In function 'prom_init_env':
arch/mips/loongson/common/env.c:49: error: ignoring return value of 'strict_strtol', declared with attribute warn_unused_result
arch/mips/loongson/common/env.c:50: error: ignoring return value of 'strict_strtol', declared with attribute warn_unused_result
arch/mips/loongson/common/env.c:51: error: ignoring return value of 'strict_strtol', declared with attribute warn_unused_result
arch/mips/loongson/common/env.c:52: error: ignoring return value of 'strict_strtol', declared with attribute warn_unused_result
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/1762/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The return value of the vmalloc() call in arch/mips/kernel/vpe.c::vpe_open()
is not checked, so we potentially store a null pointer in v->pbuffer. Add
a check for a null return and then return -ENOMEM in that case.
[Ralf: The check added by Jesper's original patch is where it logically
should be. Adding it eleminated the need for the checks in a few other
places, so I removed them. There still is a zillion of other things that
need to be fixed in this file / API.]
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1747/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If PER_LINUX32 has been set on a 32-bit kernel, only twiddle with the
low-order personality bits, let the upper bits pass through.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Cc: Camm Maguire <camm@maguirefamily.org>
Patchwork: https://patchwork.linux-mips.org/patch/1751/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The high bits of current->personality carry settings that we don't want to
clobber on each exec. Only clobber them if the lower bits that indicate
either PER_LINUX or PER_LINUX32 are invalid.
The clobbering prevents us from using useful bits like ADDR_NO_RANDOMIZE.
Reported-by: Camm Maguire <camm@maguirefamily.org>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: Camm Maguire <camm@maguirefamily.org>
Patchwork: https://patchwork.linux-mips.org/patch/1750/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes the following section mismatch:
WARNING: arch/mips/built-in.o(.text+0xc): Section mismatch in reference from the
function jz4740_init_cmdline() to the variable .init.data:arcs_cmdline
While were at it, make jz4740_init_cmdline static as well.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1755/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We never needed that (->regs[2] is overwritten on return from syscall paths
with return value of syscall, so storing it there early made no sense) and
with new restart logics since d27240bf7e61d2656de18e158ec910a902030847 it
has become really bad - we lose the original syscall number before the
place where we decide that we might need a syscall restart.
Note that for child we do need the assignment to regs[2] - it won't go
through the normal return from syscall path.
[Ralf: Issue found and reported by Lluís; initial investigations by me;
bug finally found and patch by Al; testing by me and Lluís.]
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Tested-by: Lluís Batlle i Rossell <viriketo@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* usb-next: (132 commits)
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
usb: gadget: f_ncm.c added
usb: gadget: u_ether: prepare for NCM
usb: pch_udc: Fix setup transfers with data out
usb: pch_udc: Fix compile error, warnings and checkpatch warnings
usb: add ab8500 usb transceiver driver
USB: gadget: Implement runtime PM for MSM bus glue driver
USB: gadget: Implement runtime PM for ci13xxx gadget
USB: gadget: Add USB controller driver for MSM SoC
USB: gadget: Introduce ci13xxx_udc_driver struct
USB: gadget: Initialize ci13xxx gadget device's coherent DMA mask
USB: gadget: Fix "scheduling while atomic" bugs in ci13xxx_udc
USB: gadget: Separate out PCI bus code from ci13xxx_udc
...
Extend the perf_pmu_register() interface to allow for named and
dynamic pmu types.
Because we need to support the existing static types we cannot use
dynamic types for everything, hence provide a type argument.
If we want to enumerate the PMUs they need a name, provide one.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20101117222056.259707703@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Some BIOSes use PMU resources, which can cause various bugs:
- Non-working or erratic PMU based statistics - the PMU can end up
counting the wrong thing, resulting in misleading statistics
- Profiling can stop working or it can profile the wrong thing
- A non-working or erratic NMI watchdog that cannot be relied on
- The kernel may disturb whatever thing the BIOS tries to use the
PMU for - possibly causing hardware malfunction in extreme cases.
- ... and other forms of potential misbehavior
Various forms of such misbehavior has been observed in practice - there are
BIOSes that just corrupt the PMU state, consequences be damned.
The PMU is a CPU resource that is handled by the kernel and the BIOS
stealing+corrupting it is not acceptable nor robust, so we detect it,
warn about it and further refuse to touch the PMU ourselves.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Two x86 patches broke lguest:
1) v2.6.35-492-g72d7c3b, which changed x86 to use the memblock allocator.
In lguest, the host places linear page tables at the top of mem, which
used to be enough to get us up to the swapper_pg_dir page tables. With
the first patch, the direct mapping tables used that memory:
Before: kernel direct mapping tables up to 4000000 @ 7000-1a000
After: kernel direct mapping tables up to 4000000 @ 3fed000-4000000
I initially fixed this by lying about the amount of memory we had, so
the kernel wouldn't blatt the lguest boot pagetables (yuk!), but then...
2) v2.6.36-rc8-54-gb40827f, which made x86 boot use initial_page_table.
This was initialized in a part of head_32.S which isn't executed by
lguest; it is then copied into swapper_pg_dir. So we have to initialize
it; and anyway we switch to it before we blatt the old tables, so that
fixes the previous damage as well.
For the moment, I cut & pasted the code into lguest's boot code, but
next merge window I will merge them.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
To: x86@kernel.org
lguest is dumb and drops *all* the pagetables for set_pte (which is
only used for kernel mapping manipulation, so it's OK without highmem).
But it's used a lot in boot, too. As a guest optimization, we
suppressed this flushing until the first page switch. Now we have
initial_page_table, that happens much earlier, so extend the heuristic
to wait until we switch to something other than the swapper_pg_dir or
initial_page_table.
As measured on my laptop under kvm, this dropped the time-to-mount-root
from 48 seconds to 4.3 seconds.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
fe25c7fc2e "x86: lguest: Convert to new irq chip functions" converted
enable_lguest_irq() to take a struct irq_data *, but didn't fix the one
internal caller.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
To: x86@kernel.org
Define all IRQs in irqs.h. If some IRQs are sharing one IRQ number, define
them together. If some IRQs are sharing same name with different IRQ number,
define different IRQ.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
After introducing pxa930/pxa935 and new silicons, original cpuid rules
of XScale generation 3 can't fit new silicons. Now redefine the rule
of PXA3xx.
Only PXA300/PXA310/PXA320/PXA930/PXA935 are family members of PXA3xx.
PXA930/PXA935 are family members of PXA93x. PXA93x can be considered
as PXA3xx + CP.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This is important because on PXA3xx, the physical mapping of SMEMC registers
differs from the one on PXA2xx. In order to get PCMCIA working on both PXA2xx
and PXA320, the PCMCIA driver was adjusted accordingly as well.
Also, various places in the kernel had to be patched to use
__raw_read/__raw_write.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch introduces pxa2xx_map_io() and pxa3xx_map_io() to distinguish
between PXA25x/PXA27x and PXA3xx memory mapping.
Also, fixup for platforms broken after introducing pxa{25x,27x}_map_io()
and pxa3xx_map_io() is included.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The camera registers start and range are encoded into the platform
device, and are actually handled by ioremap()'ed, thus the mapping
in pxa_map_io() is not necessary.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Initial framebuffer components. Add board-trout-panel.c
as well as platform parts to enable the framebuffer. This
code comes directly from Google's tree.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
CLK_MINMAX is used to denote clocks that have a wide variation
in possible frequencies. This handling just sets the min and
max values to the same value.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
This clock is used in the framebuffer driver as mddi_clk.
This just changes the name to match that. This also
mirrors a change in Google tree.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
This adds in the CLK_MINMAX flag to the pmdh_clk since it's actual
a min/max clock instead of a single frequency clock.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
trout has gpiolib support and interrupt support, but was
missing the gpio_to_irq function. This adds that functions
which should allow proper translation.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Change msm_iommu_map to use GFP_ATOMIC instead of
GFP_KERNEL due to the fact that the call occurs within
a spinlock-protected region.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
It seems dsp-link will do this, and tidspbridge too at some point, but
right now it's not possible to select CONFIG_MPU_BRIDGE_IOMMU.
Cc: Fernando Guzman Lugo <fernando.lugo@ti.com>
Cc: Yogesh Marathe <yogesh_marathe@ti.com>
Signed-off-by: Felipe Contreras <felipe.contreras@nokia.com>
Some IOMMUs cannot use the whole 0x0 - 0xFFFFFFFF range.
With this new API the valid range can be set.
Signed-off-by: Fernando Guzman Lugo <x0095840@ti.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
__iounmap function is wrong for OMAP architecture,
instead use iounmap which will call to the correct function.
Signed-off-by: Fernando Guzman Lugo <x0095840@ti.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
This patch adds superpages support to fixed ad address
inside iommu_kmap function.
Signed-off-by: Fernando Guzman Lugo <x0095840@ti.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
If some fixed da address is wanted to be mapped and the page
is freed but it is used as gap, the mapping will fail.
This patch is fixing that and olny keeps the gap for
not fixed address.
Signed-off-by: Fernando Guzman Lugo <x0095840@ti.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
This iomux file has been constructed from the Freescale pinmux tool.
It contains all pins from the tool, but the datasheet lists some
configurations not present in the tool, these are not yet added.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The debug registers can only be manipulated from software if monitor
debug mode is enabled. On some cores, this can never be enabled (i.e.
the corresponding bit in the DSCR is RAZ/WI).
This patch ensures we can handle this hardware configuration and fail
gracefully, rather than blow up the kernel during boot.
Reported-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Add missing header file:
arch/x86/crypto/ghash-clmulni-intel_glue.c:256: error: implicit declaration of function 'IS_ERR'
arch/x86/crypto/ghash-clmulni-intel_glue.c:257: error: implicit declaration of function 'PTR_ERR'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch actually replaces the 'struct pad_desc' with a u64 cookie
to facilitate adding platform specific pad_ctrl settings to an
existing pad definition.
So, instead of:
iomux_v3_cfg_t power_key = MX51_PAD_EIM_A27__GPIO_2_21;
power_key.pad_ctrl = MX51_GPIO_PAD_CTRL_2;
mxc_iomux_v3_setup_pad(&power_key);
one can write:
mxc_iomux_v3_setup_pad((MX51_PAD_EIM_A27__GPIO_2_21 & ~MUX_PAD_CTRL_MASK) | MX51_GPIO_PAD_CTRL_2);
Patch applies to branch 'imx-for-2.6.38' of git://git.pengutronix.de/git/imx/linux-2.6
Signed-Off-By: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We need to test for 24xx not 242x. Otherwise interrupts won't work.
Reported-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6535/1: V6 MPCore v6_dma_inv_range and v6_dma_flush_range RWFO fix
ARM: 6534/1: Make CONFIG_FPE_NWFPE depend on !CONFIG_THUMB2_KERNEL
ARM: 6533/1: Thumb-2: Make CONFIG_THUMB2_KERNEL depend on !CPU_V6
Change bcmring Maintainer list.
ARM: Update mach-types
ARM: 6528/1: Use CTR for the I-cache line size on ARMv7
ARM: 6527/1: Use CTR instead of CCSIDR for the D-cache line size on ARMv7
ARM: pxa/palm: fix ifdef around gen_nand driver registration
ARM: pxa: fix pxa2xx-flash section mismatch
ARM: mmp2: remove not used clk_rtc
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc: Write to prom console using indirect buffer.
sparc: Delete prom_*getchar().
sparc: Pass buffer pointer all the way down to prom_{get,put}char().
sparc: Do not export prom_nb{get,put}char().
sparc64: Delete prom_setcallback().
sparc64: Unexport prom_service_exists().
sparc: Kill prom devops_{32,64}.c
sparc: Remove prom_pathtoinode()
sparc64: Delete prom_puts() unused.
SPARC/LEON: removed constant timer initialization as if HZ=100, now it reflects the value of HZ
Cache ownership must be acquired by reading/writing data from the
cache line to make cache operation have the desired effect on the
SMP MPCore CPU. However, the ownership is never acquired in the
v6_dma_inv_range function when cleaning the first line and
flushing the last one, in case the address is not aligned
to D_CACHE_LINE_SIZE boundary.
Fix this by reading/writing data if needed, before performing
cache operations.
While at it, fix v6_dma_flush_range to prevent RWFO outside
the buffer.
Cc: stable@kernel.org
Signed-off-by: Valentine Barshak <vbarshak@mvista.com>
Signed-off-by: George G. Davis <gdavis@mvista.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Because the nwfpe support is unlikely to be used on new platforms
and requires CONFIG_OABI_COMPAT, which is not generally used with
ARMv7+, we shouldn't expect to build nwfpe support into a Thumb-2
kernel.
At present, nwfpe contains assembly code which isn't Thumb-2
compatible, and for now it doesn't appear useful to port this
code.
All ARMv7-A/R platforms necessarily have VFPv3 hardware floating-
point natively, making emulation unnecessary.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This makes sense, because Thumb-2 code can't execute on plain
ARMv6 processors.
This will avoid accidentally configuring a broken kernel where the
config otherwise would allow multiple architecture versions to
coexist in the same kernel.
Not adding !CPU_V5 etc., because the chance of anyone trying to
put v5 and v7 in the same kernel is low, and I'm not aware of
any mach which can do this. These could be added later if it
matters.
Note that the rules may need to be refined if support for the
ARM1156J(F)-S processor is later added to the kernel, since this
processor supports the rare ARMv6T2 extensions, which add support
for Thumb-2 and a few other ARMv7 features.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Avoid adding nasty genirq-specific code to local timers to enable PPI
interrupts. Instead, provide a gic function to do this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide a standard get_irqnr_preamble assembler macro for platforms
to use, which retrieves the base address of the GIC CPU interface
from gic_cpu_base_addr. Allow platforms to override this by defining
HAVE_GET_IRQNR_PREAMBLE.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This avoids writing unnecessarily to gic_data[] from other CPUs,
making this a mostly read-only variable.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Every architecture using the GIC has a gic_cpu_base_addr pointer for
GIC 0 for their entry assembly code to use to decode the cause of the
current interrupt. Move this into the common GIC code.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We don't need to re-pass the base address for the CPU interfaces to the
GIC for secondary CPUs, as it will never be different from the boot CPU
- and even if it was, we'd overwrite the boot CPU's base address.
Get rid of this argument, and rename to gic_secondary_init().
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide gic_init() which initializes the GIC distributor and current
CPU's GIC interface for the boot (or single) CPU.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add SMP support for ag5evm and the sh73a0 processor.
Onlining and offlining works well, but at this point
offlined processor cores are not put into sleep mode.
There is no spinlock for syncing the secondary core
with the first one in this implementation. The code
instead relies on the cpu_online() check in __cpu_up().
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add SMP base support for R-Mobile / SH-Mobile processors.
This patch contains all base code to support CONFIG_SMP
regardless of ARCH_SHMOBILE processor type. Both local timer
and CPU hotplug are supported, but no processor specific
code is included.
At this point only the default behavior is in place, so
a single core will always be used even though CONFIG_SMP
is enabled on multicore systems.
The SMP Kconfig entry for arch/arm/Kconfig is excluded from
this patch to simplify merging.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Compiling in multiple CPUs into the same kernel binary
requires a Makefile update. With this patch in place
it is possible to enable the pinmux code for both the
SH7372 and the SH7377.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When building as module:
ERROR: "cpufreq_gov_performance" [arch/arm/plat-mxc/cpufreq.ko] undefined!
WARNING: modpost: Found 1 section mismatch(es).
To see full details build your kernel with:
'make CONFIG_DEBUG_SECTION_MISMATCH=y'
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
It's due to the driver using CPUFREQ_DEFAULT_GOVERNOR, even it should not
(see commit 8122c6cea0 in Linus tree), so
remove it.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for FIQ on mx51 TZIC
TZIC changes tested with FIQ audio on an mx51 board
AVIC changes build with mx3_defconfig, not tested
Signed-off-by: Peter Horton <phorton@bitbox.co.uk>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Use clk_get to acquire the watchdog clock and also avoid hardcoding the clock name.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Interrupt-remapping gets enabled very early in the boot, as it determines the
apic mode that the processor can use. And the current code enables the vt-d
fault handling before the setup_local_APIC(). And hence the APIC LDR registers
and data structure in the memory may not be initialized. So the vt-d fault
handling in logical xapic/x2apic modes were broken.
Fix this by enabling the vt-d fault handling in the end_local_APIC_setup()
A cleaner fix of enabling fault handling while enabling intr-remapping
will be addressed for v2.6.38. [ Enabling intr-remapping determines the
usage of x2apic mode and the apic mode determines the fault-handling
configuration. ]
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
LKML-Reference: <20101201062244.541996375@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: stable@kernel.org [v2.6.32+]
Acked-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
In x2apic mode, we need to set the upper address register of the fault
handling interrupt register of the vt-d hardware. Without this
irq migration of the vt-d fault handling interrupt is broken.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
LKML-Reference: <1291225233.2648.39.camel@sbsiddha-MOBL3>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: stable@kernel.org [v2.6.32+]
Acked-by: Chris Wright <chrisw@sous-sol.org>
Tested-by: Takao Indoh <indou.takao@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
During suspend, we disable all the non boot cpus. And during resume we bring
them all back again. So no need to do alternatives_smp_switch() in between.
On my core 2 based laptop, this speeds up the suspend path by 15msec and the
resume path by 5 msec (suspend/resume speed up differences can be attributed
to the different P-states that the cpu is in during suspend/resume).
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1290557500.4946.8.camel@sbsiddha-MOBL3.sc.intel.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Alignment of alloc_bootmem() depends on the value of
L1_CACHE_SHIFT. What we need here, however, is 64 byte alignment. Use
alloc_bootmem_align() and explicitly specify the alignment instead.
This fixes a kernel boot crash reported by Jody when the cpu in .config
is set to MPENTIUMII but the kernel is booted on a xsave-capable CPU.
Reported-by: Jody Bruchon <jody@nctritech.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <20101116212442.059967454@sbsiddha-MOBL3.sc.intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@kernel.org>
The vdso Makefile passes linker-style -m options not to the linker but
to gcc. This happens to work with earlier gcc, but fails with gcc
4.6. Pass gcc-style -m options, instead.
Note: all currently supported versions of gcc supports -m32, so there
is no reason to conditionalize it any more.
Reported-by: H. J. Lu <hjl.tools@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
LKML-Reference: <tip-*@git.kernel.org>
Cc: <stable@kernel.org>
When adjusting the code to handle removing the old nmi watchdog,
I forgot to consider the compile case when the local apic is not
enabled.
This change fixes the following build error:
arch/x86/kernel/apic/hw_nmi.c:28:6: error: redefinition of ‘touch_nmi_watchdog’
Signed-off-by: Don Zickus <dzickus@redhat.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Rakib Mullick <rakib.mullick@gmail.com>
LKML-Reference: <20101213153719.GD18577@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add helper definition and function for MXS-based.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
commit 995bd3bb5 (x86: Hpet: Avoid the comparator readback penalty)
chose 8 HPET cycles as a safe value for the ETIME check, as we had the
confirmation that the posted write to the comparator register is
delayed by two HPET clock cycles on Intel chipsets which showed
readback problems.
After that patch hit mainline we got reports from machines with newer
AMD chipsets which seem to have an even longer delay. See
http://thread.gmane.org/gmane.linux.kernel/1054283 and
http://thread.gmane.org/gmane.linux.kernel/1069458 for further
information.
Boris tried to come up with an ACPI based selection of the minimum
HPET cycles, but this failed on a couple of test machines. And of
course we did not get any useful information from the hardware folks.
For now our only option is to chose a paranoid high and safe value for
the minimum HPET cycles used by the ETIME check. Adjust the minimum ns
value for the HPET clockevent accordingly.
Reported-Bistected-and-Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <alpine.LFD.2.00.1012131222420.2653@localhost6.localdomain6>
Cc: Simon Kirby <sim@hostway.ca>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Andreas Herrmann <Andreas.Herrmann3@amd.com>
Cc: John Stultz <johnstul@us.ibm.com>
The delayed TSC init function does not check whether the system has no
TSC or TSC is disabled at the kernel command line, which results in a
crash in the work queue based extended calibration due to division by
zero because the basic calibration never happened.
Add the missing checks and do not touch TSC when not available or
disabled.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <johnstul@us.ibm.com>
There are still quite a number of MFD and GPIO expander drivers that are
using the old irq_chip APIs that haven't had a chance to update during
the .37 cycle, resulting in allyes/modconfig errors on some
configurations.
Mark Brown has done most of the legwork to get these fixed up in .38,
so this should just be a .37 stop-gap that we can drop at the end of the
.38 merge window.
Reported-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch maps key0/key1/key2/key3 as HOME/MENU/BACK/POWER buttons
on mackerel board.
Signed-off-by: Tony SIM <chinyeow.sim.xt@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The current implementation of the v7_coherent_*_range function assumes
that the D and I cache lines have the same size, which is incorrect
architecturally. This patch adds the icache_line_size macro which reads
the CTR register. The main loop in v7_coherent_*_range is split in two
independent loops or the D and I caches. This also has the performance
advantage that the DSB is moved outside the main loop.
Reported-by: Kevin Sapp <ksapp@quicinc.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current implementation of the dcache_line_size macro reads the L1
cache size from the CCSIDR register. This, however, is not guaranteed to
be the smallest cache line in the cache hierarchy. The patch changes to
the macro to use the more architecturally correct CTR register.
Reported-by: Kevin Sapp <ksapp@quicinc.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit fcf173e451 (usb: musb: add names for IRQs
in structure resource) forgot to assign name to the DA8xx MUSB IRQ resource.
Because of that MUSB driver fails to load on DA8xx machines.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After Charu's GPIO hwmod patches, GPIO initialization on N800 emits
the following messages for all GPIO banks:
omap_hwmod: gpio1: cannot be enabled (3)
This is due to OMAP24XX_ST_GPIOS_SHIFT being defined as a bitmask.
Fix this and also fix two other macros that had the same problem.
Thanks to Tony Lindgren <tony@atomide.com> for originally reporting
this bug.
Signed-off-by: Paul Walmsley <paul@pwsan.com
Cc: Charulatha Varadarajan <charu@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Function qeth_l3_arp_query now queries for IPv6 addresses, too, if
QETH_QARP_WITH_IPV6 is passed as parameter to the ioctl. HiperSockets
and GuestLAN in HiperSockets mode provide corresponding entries.
Signed-off-by: Einar Lueck <elelueck@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Please use omap1_defconfig instead, or search online
for a more optimized defconfig for your omap1 board.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omap1_defconfig this should be eventually usable for booting
all omap1 machines. Generated based on:
$ grep ARCH_OMAP1=y arch/arm/configs/* | cut -d: -f1 | xargs cat | \
sort | uniq >> arch/arm/configs/omap1_defconfig
Then change few things manually, like use Nokia 770 CONFIG_CMDLINE
as it does not allow setting it in the bootloader.
Finally ran make savedefconfig on it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise multi-omap1 support for omap1 won't work as the cpu_class_is_omap1()
won't work until the SoC is detected.
Note that eventually these will go away, please use ioremap + read/write instead.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Ensure that the at24 eeprom driver is selected for certain boards that
need boot data (e.g. MAC address) from EEPROM.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
There was a single case of 'da850evm' prefix in the board-da850-evm.c file
where the reset of the prefixes were 'da850_evm'; change it to 'da850_evm' for
consistency.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Change the mach-davinci Kconfig file so that GPIO_PCA953X is default when
MACH_DAVINCI_DA850_EVM is set instead of always selecting. This allows users
to compile pca953x as a module.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Sergei Shtylyov <sshtylyov@mvista.com>
CC: Nori, Sekhar <nsekhar@ti.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
When the RMII PHY on the UI board is enabled with CONFIG_DA850_UI_RMII
then then following will be printed to the console when warnings are
also enabled:
WARNING: at drivers/gpio/gpiolib.c:1567 __gpio_set_value+0x4c/0x5c()
Modules linked in:
[<c002c6ac>] (unwind_backtrace+0x0/0xf8) from [<c003b48c>] (warn_slowpath_common+0x4c/0x64)
[<c003b48c>] (warn_slowpath_common+0x4c/0x64) from [<c003b4c0>] (warn_slowpath_null+0x1c/0x24)
[<c003b4c0>] (warn_slowpath_null+0x1c/0x24) from [<c01aed60>] (__gpio_set_value+0x4c/0x5c)
[<c01aed60>] (__gpio_set_value+0x4c/0x5c) from [<c0033bd4>] (da850_evm_ui_expander_setup+0x1e4/0x2
44)
[<c0033bd4>] (da850_evm_ui_expander_setup+0x1e4/0x244) from [<c02e2e1c>] (pca953x_probe+0x1f8/0x29
0)
<snip>
Traced the WARN_ON to the gpio_set_value(rmii_sel,0) call in
da850_evm_setup_emac_rmii. Replacing the call with the _cansleep variant
results in no more warning. Also replacing the gpio_set_value calls in the
teardown function.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Chris Cordahi <christophercordahi@nanometrics.ca>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
aemif_calc_rate() can return a negative error value, so all the
variables that get tested for this value need to be signed.
The maximum bit width of WSETUP(WSETUP_MAX) appears to be 30 bits
(0xf << 26). Using a signed instead of an unsigned integer
shouldn't make a difference here.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
A common do-while loop can be factored out from the end of
the branches.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch applies the following modifications to the tnetv107x clock tree:
- reparent tnetv107x usb clocks to usbss
- mark timer1 as always enabled
- enable set_rate on pll divider output clocks
- adjust tnetv107x tsc sysclk rate lower to fix invalid reset defaults
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch modifies the sysclk rate setting code to use the divider mask
specified in pll_data. Without this, devices with different divider ranges
(e.g. tnetv107x) fail.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Overwrite the default implementation of sched_clock that is based on
jiffies by something more precise. This improves timestamps in ftrace.
Implementation is copied from OMAP platform code.
Signed-off-by: Andreas Gaeer <Andreas.Gaer@baslerweb.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Enabling the musb OTG mode for SDP and PANDA boards.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Registering the twl6030-usb transceiver device as a child to twl6030 core.
Removed the NOP transceiver init call from board file.
Populated twl4030_usb_data platform data structure with the function
pointers for OMAP4430 internal PHY operation to be used by twl630-usb driver.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
setup_local_APIC() is used to setup local APIC early during CPU
initialization and already assumes that preemption is disabled on
entry. However, The function unnecessarily disables and enables
preemption and uses smp_processor_id() multiple times in and out of
the nested preemption disabled section. This gives the wrong
impression that the function might be able to handle being called with
preemption enabled and/or migrated to another processor in the middle.
Make it clear that the function is always called with preemption
disabled, drop the confusing preemption disable block and call
smp_processor_id() once at the beginning of the function.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Cyrill Gorcunov <gorcunov@gmail.com>
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: brgerst@gmail.com
LKML-Reference: <4D00B3B9.7060702@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Selecting the twl6030-usb for OMAP4430SDP and OMAP4PANDA boards and
adding OMAP4 internal phy code for compilation
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Adding the twl6030-usb transceiver support for OMAP4 musb driver.
OMAP4 supports 2 types of transceiver interface.
1. UTMI: The PHY is embedded within OMAP4. The transceiver functionality
is split between the twl6030 PMIC chip and OMAP4430. The VBUS, ID pin
sensing and OTG SRP generation part is integrated in TWL6030 and UTMI PHY
functionality is embedded within the OMAP4430.
There is no direct interactions between the MUSB controller and TWL6030
chip to communicate the session-valid, session-end and ID-GND events.
It has to be done through a software by setting/resetting bits in
one of the control module register of OMAP4430 which in turn toggles
the appropriate signals to MUSB controller.
The internal transceiver has functional clocks and
powerdown bits to powerdown the PHY for power saving.
Since there is no option available for having 2 transceiver drivers
for one USB controller, internal PHY specific APIs are passed through
plaform_data function pointers to use in the twl6030-usb transceiver
driver.
2. ULPI interface is provided for off-chip transceivers.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 4814ced511 (OMAP:
control: move plat-omap/control.h to mach-omap2/control.h)
moved <plat/control.h> to another location, preventing
drivers from accessing it, so we need to pass function
pointers from arch code to be able to talk to internal
PHY on AM35x.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
musb core doesn't need to know about platform
specific details. So start moving clock
handling to platform glue layer and make
musb core agnostic about that.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Just adding its own platform_driver, not really
using it yet.
Later patches will come to split power management
code from musb_core and move it completely to HW
glue layer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Just adding its own platform_driver, not really
using it yet.
When all HW glue layers are converted, more patches
will come to split power management code from musb_core
and move it completely to HW glue layer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Just adding its own platform_driver, not really
using it yet.
When all HW glue layers are converted, more patches
will come to split power management code from musb_core
and move it completely to HW glue layer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Just adding its own platform_driver, not really
using it yet.
When all HW glue layers are converted, more patches
will come to split power management code from musb_core
and move it completely to HW glue layer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Just adding its own platform_driver, not really
using it yet.
When all HW glue layers are converted, more patches
will come to split power management code from musb_core
and move it completely to HW glue layer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Just adding its own platform_driver, not really
using it yet.
When all HW glue layers are converted, more patches
will come to split power management code from musb_core
and move it completely to HW glue layer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
change all ocurrences of musb_hdrc to musb-hdrc.
We will call glue layer drivers musb-<glue layer>,
so in order to keep things somewhat standard, let's
change the underscore into a dash.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This will make things simpler when choosing which
glue layer to compile. It avoids a lot of magic
around the "default" Kconfig option and lets the
user choose what exactly s/he wants to compile.
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 0d8e2d0dad (OMAP2+: PM/serial:
hold console semaphore while OMAP UARTs are disabled) added use of the
console semaphore to protect UARTs from being accessed after disabled
during idle, but this causes problems in suspend.
During suspend, the console semaphore is acquired by the console
suspend method (console_suspend()) so the try_acquire_console_sem()
will always fail and suspend will be aborted.
To fix, introduce a check so the console semaphore is only attempted
during idle, and not during suspend. Also use the same check so that
the console semaphore is not prematurely released during resume.
Thanks to Paul Walmsley for suggesting adding the same check during
resume.
Cc: Paul Walmsley <paul@pwsan.com>
Tested-by: Jean Pihet <j-pihet@ti.com>
Tested-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Kernel was failing to boot on omap1611 based OSK boards due to
mis-configured SRAM size. Existing code was using a hard-coded value
for 250k, which was then rounded down by PAGE_SIZE. Increasing this to
256k allows kernel to boot on omap1611 SoCs.
Problem reported by and initial fix suggested by Tim Bird.
Thanks to Tony Lindgren for helping diagnose the problem to being
specific to OMAP1611 and not affecting OMAP1610/OMAP1623.
Reported-by: Tim Bird <tim.bird@am.sony.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Initialize asm_irq_flags in omap_init_irq and use it in
get_irqnr_and_base to detect between omap7xx and omap15xx/16xx.
Note that both INT_1510_IH2_IRQ and INT_1510_IH2_IRQ are defined
as 0, so use INT_1510_IH2_IRQ for both of them.
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix a typo in:
004417a6d468: perf, arch: Cleanup perf-pmu init vs lockup-detector
Which caused a build failure on Sparc, reported by Stephen Rothwell.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Originally adapted from Huang Ying's patch which moved the
unknown_nmi_panic to the traps.c file. Because the old nmi
watchdog was deleted before this change happened, the
unknown_nmi_panic sysctl was lost. This re-adds it.
Also, the nmi_watchdog sysctl was re-implemented and its
documentation updated accordingly.
Patch-inspired-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Reviewed-by: Cyrill Gorcunov <gorcunov@gmail.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: fweisbec@gmail.com
LKML-Reference: <1291068437-5331-3-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
My patch that removed the old x86 nmi watchdog broke other
arches. This change reverts a piece of that patch and puts the
change in the correct spot.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Reviewed-by: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: fweisbec@gmail.com
Cc: yinghai@kernel.org
LKML-Reference: <1291068437-5331-2-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
assign_to_mp_irq() is copying the struct mpc_intsrc members one by
one. That's silly. Use memcpy() and let the compiler figure it out.
Same for the identical function assign_to_mpc_intsrc()
mp_irq_mpc_intsrc_cmp() is comparing the struct members one by one,
but no caller ever checks the different return codes. Use memcmp()
instead.
Remove the extra printk in MP_ioapic_info()
Signed-off-by: Feng Tang <feng.tang@linux.intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Alan Cox <alan@linux.intel.com>
Cc: Len Brown <len.brown@intel.com>
LKML-Reference: <20101208151857.212f0018@feng-i7>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There are 3 places defining similar functions of saving IRQ vector
info into mp_irqs[] array: mmparse/acpi/mrst.
Replace the redundant code by a common function in io_apic.c as it's
only called when CONFIG_X86_IO_APIC=y
Signed-off-by: Feng Tang <feng.tang@intel.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <20101207133204.4d913c5a@feng-i7>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
For 32bit mptable path, setup_ids_from_mpc() always writes the io_apic
id register, even there is no change needed.
Skip the write, when readout and mptable match.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
LKML-Reference: <4CFDF785.7010401@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If x2apic is preenabled and used by the kernel, we don't need to map
the lapic address. That mapping will never be used.
So just skip that in register_lapic_address()
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
LKML-Reference: <4CFDF69C.9070501@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
register_lapic_address() and mp_sfi_register_lapic_address() are
almost identical. Use the common function.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Len Brown <lenb@kernel.org>
LKML-Reference: <4CFDF693.6000908@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Remove the printk as well, we don't want to print when nothing
changed. We print in register_lapic_address() already.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
LKML-Reference: <4CFDF68A.7020902@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
It is almost the same as smp_register_lapic_addr(). We just need to
let smp_read_mpc() call smp_register_lapic_addr() when early==1.
Add the apic_printk to smp_register_lapic_address()
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
LKML-Reference: <4CFDF681.3030509@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
They are the same, move the common function to apic.c to allow
further cleanups.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Len Brown <lenb@kernel.org>
LKML-Reference: <4CFDF675.4060305@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reason: apic cleanup series depends on x86/apic, x86/amd-nb x86/platform
Conflicts:
arch/x86/include/asm/io_apic.h
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
arch/x86/kernel/apic/io_apic.c: In function 'ack_apic_level':
arch/x86/kernel/apic/io_apic.c:2433: warning: unused variable 'desc'
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <201010272107.o9RL7rse018212@imap1.linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
arch/x86/kernel/apic/hw_nmi.c:29: warning: backtrace_mask defined but not used
commit 0e2af2a9(x86, hw_nmi: Move backtrace_mask declaration under
ARCH_HAS_NMI_WATCHDOG) addressed this warning, but it was reintroduced
by commit 5f2b0ba4(x86, nmi_watchdog: Remove the old nmi_watchdog).
Move backtrace_mask into the #ifdef arch_trigger_all_cpu_backtrace
section again.
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <AANLkTi=rcc38QzoKa6LFy4m++-p_9=Zt4_kDQE=GeKxf@mail.gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Adds support in PRCMU driver to handle CPU and APE operating points.
Signed-off-by: Martin Persson <martin.persson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Since all the hotplug stuff is serialized by the hotplug mutex,
do away with the amd_nb_lock.
Cc: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently the number of CPUID leaves KVM handles is limited to 40.
My desktop machine (AthlonII) already has 35 and future CPUs will
expand this well beyond the limit. Extend the limit to 80 to make
room for future processors.
KVM-Stable-Tag.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
To support xsave properly for the guest the SVM module need
software support for it. As long as this is not present do
not report the xsave as supported feature in cpuid.
As a side-effect this patch moves the bit() helper function
into the x86.h file so that it can be used in svm.c too.
KVM-Stable-Tag.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
CPUID's OSXSAVE is a mirror of CR4.OSXSAVE bit. We need to update the CPUID
after migration.
KVM-Stable-Tag.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/pvclock: Zero last_value on resume
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf record: Fix eternal wait for stillborn child
perf header: Don't assume there's no attr info if no sample ids is provided
perf symbols: Figure out start address of kernel map from kallsyms
perf symbols: Fix kallsyms kernel/module map splitting
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
nohz: Fix printk_needs_cpu() return value on offline cpus
printk: Fix wake_up_klogd() vs cpu hotplug
We don't need to repeat the same definitions of the ioremap*(),
once in terms of __arch_ioremap() and again in terms of __arm_ioremap().
Instead, if the platform hasn't provided an __arch_ioremap, define
this to be __arm_ioremap, and only define the ioremap*() set using
__arch_ioremap.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Defining iounmap() with arguments prevents it from being used as a
function pointer, causing platforms to work around this. Instead,
define it to be a simple macro.
Do the same for __arch_io(re|un)map too.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The DB5500 PER6 clock rate is the same as the DB8500 one, i.e. 133.33 MHz.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Remove the irq number macros which don't specify which SoC they're for.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Platforms may choose not to provide an additional name for the GPIO
block.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
The uncompress code for zImage uses the UART to print status messages,
this was hard coded to use UART2 for the U8500 platform. This patch
checks at run time which platform it is run on. U5500 uses UART0 as
console UART.
Signed-off-by: Carl-Johan Irekvist <carl-johan.irekvist@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Add basic DMA configuration for u5500 supporting memcpy.
Make way for SDI0 dma support by setting SDI0 to -1,
indicating it will be configured in runtime.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
U5500 now boots from sdi0 (onboard eMMC).
Change machine type to U5500.
Adjust uart and sdi0 clock rates for u5500.
All necessary clocks must be enabled before Linux starts because
there is no clock tree support in u5500 yet.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
PRCMU driver only supports u8500. Don't
initialize prcmu if running on u5500.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
PRCM_TCR enables the various timers in the system. This must be achieved
before any of the MTUs are usable for kernel usage. Explicit enabling of
this in the kernel makes it independent of bootloader actions.
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
In the nomadik GPIO pin configuration, allow the sleep mode direction
and pull configurations to differ from the ones for the normal state.
PIN_SLPM_PULL_*, PIN_SLPM_INPUT, PIN_SLPM_OUTPUT* macros are provided
for this.
Since the hardware does not allow seperate configurations for sleep mode
and normal mode, this is implemented by having software remux the
configurations as necessary.
Reviewed-by: Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
This patch removes the dublicated define for number of
interrupts and instead include the needed header file.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
This patch adds support for db8500 chip version 2.
The TCDM memory address of the PRCMU is changed and
dynamic detection of that is added.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Change the Ux500 devices to be dynamically allocated and added by
calling functions instead of referencing structures, thereby allowing
5500 and other derivatives' support to be added without having to
duplicate structures, use fixup functions, or use compile-time macros.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
clk_get() return value should be checked with IS_ERR().
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently the {set,get}_pull callbacks of the s3c24xx_gpiocfg_default structure
are initalized via s3c_gpio_{get,set}pull_1up. This results in a linker
error when only CONFIG_CPU_S3C2442 is selected:
arch/arm/plat-s3c24xx/built-in.o:(.data+0x13f4): undefined reference to
`s3c_gpio_getpull_1up'
arch/arm/plat-s3c24xx/built-in.o:(.data+0x13f8): undefined reference to
`s3c_gpio_setpull_1up'
The s3c2442 has pulldowns instead of pullups compared to the s3c2440.
The method of controlling them is the same though.
So this patch modifies the existing s3c_gpio_{get,set}pull_1up helper functions
to take an additional parameter deciding whether the pin has a pullup or pulldown.
The s3c_gpio_{get,set}pull_1{down,up} functions then wrap that functions passing
either S3C_GPIO_PULL_UP or S3C_GPIO_PULL_DOWN.
Furthermore this patch sets up the s3c24xx_gpiocfg_default.{get,set}_pull fields
in the s3c244{0,2}_map_io function to the new pulldown helper functions.
Based on patch from "Lars-Peter Clausen" <lars@metafoo.de>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
We need to divide the 15xx/16xx offset by 2 for 7xx. Use bank->stride
for that. This allows us to get rid of the duplicate defines for the
MPUIO registers.
Note that this will cause omap-keypad.c driver to not work on 7xx.
However, the right fix there is to move over to matrix_keypad instead
as suggested by Cory Maccarrone <darkstar6262@gmail.com> and
Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>.
Cc: Cory Maccarrone <darkstar6262@gmail.com>
Acked-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Implement GPIO as a platform device.
GPIO APIs are used in machine_init functions. Hence it is
required to complete GPIO probe before board_init. Therefore
GPIO device register and driver register are implemented as
postcore_initcalls.
omap_gpio_init() does nothing now and this function would be
removed in the next patch as it's usage is spread across most
of the board files.
Inorder to convert GPIO as platform device, modifications are
required in clockxxxx_data.c file for OMAP1 so that device names
can be used to obtain clock instead of getting clocks by
name/NULL ptr.
Use runtime pm APIs (pm_runtime_put*/pm_runtime_get*) for enabling
or disabling the clocks, modify sysconfig settings and remove usage
of clock FW APIs.
Note 1: Converting GPIO driver to use runtime PM APIs is not done as a
separate patch because GPIO clock names are different for various OMAPs
and are different for some of the banks in the same CPU. This would need
usage of cpu_is checks and bank id checks while using clock FW APIs in
the gpio driver. Hence while making GPIO a platform driver framework,
PM runtime APIs are used directly.
Note 2: While implementing GPIO as a platform device, pm runtime APIs
are used as mentioned above and modification is not done in gpio's
prepare for idle/ resume after idle functions. This would be done
in the next patch series and GPIO driver would be made to use dev_pm_ops
instead of sysdev_class in that series only.
Due to the above, the GPIO driver implicitly relies on
CM_AUTOIDLE = 1 on its iclk for power management to work, since the
driver never disables its iclk.
This would be taken care in the next patch series (see Note 3 below).
Refer to
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg39112.html
for more details.
Note 3: only pm_runtime_get_sync is called in gpio's probe() and
pm_runtime_put* is never called. This is to make the implementation
similar to the existing GPIO code. Another patch series would be sent
to correct this.
In OMAP3 and OMAP4 gpio's debounce clocks are optional clocks. They
are enabled/ disabled whenever required using clock framework APIs
TODO:
1. Cleanup the GPIO driver. Use function pointers and register
offest pointers instead of using hardcoded values
2. Remove all cpu_is_ checks and OMAP specific macros
3. Remove usage of gpio_bank array so that only
instance specific information is used in driver code
4. Rename 'method'/ avoid it's usage
5. Fix the non-wakeup gpios handling for OMAP2430, OMAP3 & OMAP4
6. Modify gpio's prepare for idle/ resume after idle functions
to use runtime pm implentation.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Basak, Partha <p-basak2@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: updated for bank specific revision and updated boards]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use omap_device_build() API to do platform_device_register of
GPIO devices. For OMAP2+ chips, the device specific data defined
in the centralized hwmod database will be used.
gpio_init needs to be done before machine_init functions access
gpio APIs. Hence gpio_init is made as a postcore_initcall.
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Reviewed-by: Basak, Partha <p-basak2@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add GPIO hwmod data for OMAP4
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add GPIO hwmod data for OMAP3
Also remove "omap34xx.h" header file as it is not required
anymore.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add GPIO hwmod data for OMAP2430
Also remove "omap24xx.h" header file as it is not required
anymore.
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add GPIO hwmod data for OMAP2420 and add the required
GPIO device attributes in the gpio header file
Also remove "omap24xx.h" header file as it is not required
anymore.
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for handling OMAP7xx specific gpio_init by
providing platform device data and doing device registration.
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for handling OMAP16xx specific gpio_init by
providing platform device data and doing device registration.
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for handling OMAP15xx specific gpio_init by
providing platform device data and doing device registration.
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise GPIO init on 16xx may try to access uninitialized GPIO
bank as the MPUIO bank does not have a revision register.
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Prepare for implementing GPIO as a platform driver.
Modifies omap_gpio_init() to make use of omap_gpio_chip_init()
and omap_gpio_mod_init(). omap_gpio_mod_init() does the module init
by clearing the status register and initializing the GPIO control register.
omap_gpio_chip_init() initializes the chip request, free, get, set and
other function pointers and sets the gpio irq handler.
This is only to reorganize the code so that the "omap gpio platform driver
implementation patch" looks cleaner and better to review.
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like some boards are calling gpio_request from init_irq.
This will make the request_irq fail, as GPIO will be initialized
as postcore_initcall.
Reported-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Using true/false instead of 1/0 to update the free variable.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Function omap_mcbsp_probe allocates struct omap_mcbsp *mcbsp but it is not
freed in omap_mcbsp_remove. Fix this, remove unneeded structure cleanups
and clk_disable calls since they are not needed here.
This is not problem currently but becomes if the mcbsp driver is ever
modularized.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Value of "isr_reg" pointer is depend on configuration and GPIO method.
Potentially it may have NULL value and it is dereferenced later
in code. Warning and exit from function are added in this case.
Signed-off-by: Evgeny Kuznetsov <EXT-Eugeny.Kuznetsov@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In some cases we can get error function `omap2_i2c_add_bus':
arch/arm/plat-omap/i2c.c:136: undefined reference to `omap2_i2c_mux_pins'
arch/arm/plat-omap/i2c.c:141: undefined reference to `omap_hwmod_lookup'
arch/arm/plat-omap/i2c.c:157: undefined reference to `omap_device_build'
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 4d17aeb1c5 ("OMAP: I2C: split
device registration and convert OMAP2+ to omap_device") broke I2C on
OMAP1. The following messages appear at boot:
i2c_omap i2c_omap.1: failure requesting irq 0
i2c_omap: probe of i2c_omap.1 failed with error -22
Investigation revealed that a chunk of code is missing from the
original plat-omap/i2c.c file which configured the IRQ and base address
for the I2C block on OMAP1. Upon adding this back, the OMAP1 I2C block
seems to initialize correctly.
Thanks to Cory Maccarrone <darkstar6262@gmail.com> for reporting the bug,
and apologies for the breakage.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Tested-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the name of interrupt mask alteration function (ie the
local_change_intr_mask_level() fn) called in gdbstub to have an arch_
prefix to match the definition in asm/irqflags.h.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
MX51 has two watchdog modules.
Add support for both of them.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for the QNAP NAS devices based on Marvell's 6282 Kirkwood
chip (TS-119P+, TS-219P+ and TS-419P+). The differences to the 6281
based devices are:
- Ethernet PHY address
- GPIOs used for buttons (TS-119P+/TS-219P+)
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Saeed Bishara <saeed.bishara@gmail.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Adds support for Buffalo Linkstation Live v3 (LS-CHL) NAS drives.
Signed-off-by: Ash Hughes <ashley.hughes@blueyonder.co.uk>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Common GIC entry macro for omap
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the GIC demux code in asm/hardware/entry-macro-gic.S
on the Versatile Express subarchitecture.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the GIC demux code in asm/hardware/entry-macro-gic.S
on the UX500 subarchitecture.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the GIC demux code in asm/hardware/entry-macro-gic.S
on the Tegra subarchitecture.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the GIC demux code in asm/hardware/entry-macro-gic.S
on the Realview subarchitecture.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the GIC demux code in asm/hardware/entry-macro-gic.S
on the CNS3XXX subarchitecture.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch is the identical GIC demux implementation
merge V3. Instead of implementing same code over and
over simply share it in entry-macro-gic.S. The shared
code is based on the realview implementation.
Each GIC demux instance still has to setup the base address
of the controller using the get_irqnr_preamble macro. The
rest of the GIC specific code can be shared.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 0ea1293009 ("arm: return both physical and virtual addresses
from addruart") took out the test for MMU on/off but didn't switch the
ldr instructions to no longer be conditionals based on said test.
Fix that.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
clk_get() returns ERR_PTR() on error, not NULL.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: updated to include err.h to compile on omap1]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch complements ed919b0 "mmc: sdio: fix runtime PM anomalies by
introducing MMC_CAP_POWER_OFF_CARD" by declaring MMC_CAP_POWER_OFF_CARD
on the ZOOM's wl1271 mmc slot.
This is required in order not to break runtime PM support for the wl1271
sdio driver.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6524/1: GIC irq desciptor bug fix
ARM: 6523/1: iop: ensure sched_clock() is notrace
ARM: 6456/1: Fix for building DEBUG with sa11xx_base.c as a module.
ARM: 6519/1: kuser: Fix incorrect cmpxchg syscall in kuser helpers
ARM: 6505/1: kprobes: Don't HAVE_KPROBES when CONFIG_THUMB2_KERNEL is selected
ARM: 6508/1: vexpress: Correct data alignment in headsmp.S for CONFIG_THUMB2_KERNEL
ARM: 6507/1: RealView: Correct data alignment in headsmp.S for CONFIG_THUMB2_KERNEL
ARM: 6504/1: Thumb-2: Fix long-distance conditional branches in head.S for Thumb-2.
ARM: 6503/1: Thumb-2: Restore sensible zImage header layout for CONFIG_THUMB2_KERNEL
ARM: 6502/1: Thumb-2: Fix CONFIG_THUMB2_KERNEL breakage in compressed/head.S
ARM: 6501/1: Thumb-2: Correct data alignment for CONFIG_THUMB2_KERNEL in mm/proc-v7.S
ARM: 6500/1: Thumb-2: Correct data alignment for CONFIG_THUMB2_KERNEL in kernel/head.S
ARM: 6499/1: Thumb-2: Correct data alignment for CONFIG_THUMB2_KERNEL in bootp/init.S
ARM: 6498/1: vfp: Correct data alignment for CONFIG_THUMB2_KERNEL
ARM: 6497/1: kexec: Correct data alignment for CONFIG_THUMB2_KERNEL
ARM: 6496/1: GIC: Do not try to register more then NR_IRQS interrupts
ARM: cns3xxx: Fix build with CONFIG_PCI=y
Move the code to arch/x86/platform/mrst/. Also fix a typo to use
the correct config option: ONFIG_EARLY_PRINTK_MRST
Signed-off-by: Feng Tang <feng.tang@intel.com>
Cc: alan@linux.intel.com
LKML-Reference: <1291348298-21263-1-git-send-email-feng.tang@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use text_poke_smp_batch() on unoptimization path for reducing
the number of stop_machine() issues. If the number of
unoptimizing probes is more than MAX_OPTIMIZE_PROBES(=256),
kprobes unoptimizes first MAX_OPTIMIZE_PROBES probes and kicks
optimizer for remaining probes.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: 2nddept-manager@sdl.hitachi.co.jp
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <20101203095434.2961.22657.stgit@ltc236.sdl.hitachi.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use text_poke_smp_batch() in optimization path for reducing
the number of stop_machine() issues. If the number of optimizing
probes is more than MAX_OPTIMIZE_PROBES(=256), kprobes optimizes
first MAX_OPTIMIZE_PROBES probes and kicks optimizer for
remaining probes.
Changes in v5:
- Use kick_kprobe_optimizer() instead of directly calling
schedule_delayed_work().
- Rescheduling optimizer outside of kprobe mutex lock.
Changes in v2:
- Allocate code buffer and parameters in arch_init_kprobes()
instead of using static arraies.
- Merge previous max optimization limit patch into this patch.
So, this patch introduces upper limit of optimization at
once.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: 2nddept-manager@sdl.hitachi.co.jp
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <20101203095428.2961.8994.stgit@ltc236.sdl.hitachi.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Introduce text_poke_smp_batch(). This function modifies several
text areas with one stop_machine() on SMP. Because calling
stop_machine() is heavy task, it is better to aggregate
text_poke requests.
( Note: I've talked with Rusty about this interface, and
he would not like to expand stop_machine() interface, since
it is not for generic use. )
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: 2nddept-manager@sdl.hitachi.co.jp
LKML-Reference: <20101203095422.2961.51217.stgit@ltc236.sdl.hitachi.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Unoptimization occurs when a probe is unregistered or disabled,
and is heavy because it recovers instructions by using
stop_machine(). This patch delays unoptimization operations and
unoptimize several probes at once by using
text_poke_smp_batch(). This can avoid unexpected system slowdown
coming from stop_machine().
Changes in v5:
- Split this patch into several cleanup patches and this patch.
- Fix some text_mutex lock miss.
- Use bool instead of int for behavior flags.
- Add additional comment for (un)optimizing path.
Changes in v2:
- Use dynamic allocated buffers and params.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: 2nddept-manager@sdl.hitachi.co.jp
LKML-Reference: <20101203095409.2961.82733.stgit@ltc236.sdl.hitachi.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit a5ef2e70 "x86: Sanitize apb timer interrupt handling" forgot
the affinity setup when cleaning up the code, this patch just
adds the forgotten part
Signed-off-by: Feng Tang <feng.tang@intel.com>
Cc: Jacob Pan <jacob.jun.pan@intel.com>
Cc: Alan Cox <alan@linux.intel.com>
LKML-Reference: <1291348298-21263-2-git-send-email-feng.tang@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch enables the UART on the CE4100. The UART has a couple of
issues that need to be worked around. First the UART is mostly PC
compatible except that it is clocked eight times faster than a
standard PC so the default configuration provided in
arch/x86/include/asm/serial.h needs to be overridden. Second the TX
interrupt may not be set correctly all the time. Lastly accessing the
UART via I/O space for early_prink() hangs the chip when the IOAPIC is
enabled.
A custom mem_serial_in() is provided to work around the TX interrupt
issue. The configuration issues are dealt with in the call back
registered with the 8250 driver via serial8250_set_isa_configurator()
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
LKML-Reference: <1290436128-17958-1-git-send-email-dirk.brandewie@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Sodaville needs to setup the IO_APIC ids as the boot loader leaves
them uninitialized. Split out the setter function so it can be called
unconditionally from the sodaville board code.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <20101126165020.GA26361@www.tglx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
sparse doesn't like per-cpu accesses such as:
static DEFINE_PER_CPU(struct perf_event *, foo[MAXLEN]);
struct perf_event **bar = __get_cpu_var(foo);
and shouts quite loudly about it:
| warning: incorrect type in assignment (different modifiers)
| expected struct perf_event **slots
| got struct perf_event *[noderef] *<noident>
This patch adds casts to these sorts of assignments in hw_breakpoint.c
in order to silence the warnings.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Single-stepping a breakpoint requires us to disable it temporarily so that
we don't get stuck in a recursive debug trap. With per-cpu breakpoints this
presents a problem where an interrupt can be taken before the single-step has
completed and a new task is eventually scheduled. This new task will not
hit the breakpoint because it will have been disabled during the previous
handling code.
This patch disallows per-cpu breakpoints on ARM when an overflow handler
is not present. A similar effect can be created by placing breakpoints on
a shell and then running applications there.
Signed-off-by: Will Deacon <will.deacon@arm.com>
The single-stepping code is currently different depending on whether
we are stepping over a breakpoint or a watchpoint. There is no good
reason for this, so let's sort it out.
This patch adds functions for enabling/disabling single-step for
a particular hw_breakpoint and integrates this with the exception
handling code.
Signed-off-by: Will Deacon <will.deacon@arm.com>
The watchpoint single-stepping code calls register_user_hw_breakpoint to
register a mismatch breakpoint for stepping over the watchpoint. This is
performed with preemption disabled, which is unsafe as we may end up scheduling
whilst in_atomic(). Furthermore, using the perf API is rather overkill since
we are already in the hw-breakpoint backend and only require access to reserved
breakpoints anyway.
This patch reworks the watchpoint stepping code so that we don't require
another perf_event for the mismatch breakpoint. Instead, we hold a separate
arch_hw_breakpoint_ctrl struct inside the watchpoint which is used exclusively
for stepping. We can check whether or not stepping is enabled when installing
or uninstalling the watchpoint and operate on the breakpoint accordingly.
Signed-off-by: Will Deacon <will.deacon@arm.com>
To permit handling of watchpoint exceptions without signalling a
debugger, it is necessary to reserve breakpoint registers for in-kernel
use only.
This patch ensures that we record and subtract the number of reserved
breakpoints from the number of usable breakpoint registers that we
advertise to userspace via the ptrace API.
Signed-off-by: Will Deacon <will.deacon@arm.com>
On ARM, debug exceptions occur in the form of data or prefetch aborts.
One difference is that debug exceptions require access to per-cpu banked
registers and data structures which are not saved in the low-level exception
code. For kernels built with CONFIG_PREEMPT, there is an unlikely scenario
that the debug handler ends up running on a different CPU from the one
that originally signalled the event, resulting in random data being read
from the wrong registers.
This patch adds a debug_entry macro to the low-level exception handling
code which checks whether the taken exception is a debug exception. If
it is, the preempt count for the faulting process is incremented. After
the debug handler has finished, the count is decremented.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The current hw_breakpoint code tries to fix up the alignment of
breakpoints so that we can make use of sparse byte-address-select
bits in the control register and give the illusion that we can
set breakpoints on unaligned addresses.
Although this works on v6 cores, v7 forbids this behaviour, instead
requiring breakpoints to be set on aligned addresses and have contiguous
byte-address-select ranges depending on the instruction set in use.
For ARM the only supported size is 4 bytes, whilst Thumb-2 also permits
2 byte breakpoints (watchpoints can be of 1, 2, 4 or 8 bytes long).
This patch simplifies the alignment fixup code so that we require
addresses to be aligned to the size of the corresponding breakpoint.
This allows us to handle the common case of breaking on a half-word
aligned Thumb-2 instruction and also allows us to set byte watchpoints
on arbitrary addresses.
Signed-off-by: Will Deacon <will.deacon@arm.com>
The ARMv7 debug architecture doesn't make any guarantees about the
contents of debug control registers following a debug logic reset.
This patch ensures that we reset the control registers when a cpu
comes ONLINE (for example, with hotplug) so that when we enable
monitor mode while inserting a breakpoint we won't exhibit random
behaviour.
Signed-off-by: Will Deacon <will.deacon@arm.com>
ARMv7 architects a system for saving and restoring the debug registers
across low-power modes. At the heart of this system is a lock register
which, when set, forbids writes to the debug registers. While locked,
writes to debug registers via the co-processor interface will result
in undefined instruction traps. Linux currently doesn't make use of
this feature because we update the debug registers on context switch
anyway, however the status of the lock is IMPLEMENTATION DEFINED on
reset.
This patch ensures that the lock is cleared during boot so that we
can write to the debug registers safely.
Signed-off-by: Will Deacon <will.deacon@arm.com>
gic_set_cpu will directly use irq_desc[]. If CONFIG_SPARSE_IRQ is
enabled, there is no irq_desc[]. So we need use irq_to_desc(irq) to
get the descriptor for irq.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
parisc: Fix GSC PS/2 driver name for keyboard and mouse
parisc: KittyHawk LCD fix
parisc: convert the rest of the irq handlers to simple/percpu
parisc: fix dino/gsc interrupts
parisc: remove redundant initialization in sigsegv path of sys_rt_sigreturn
It is kernel-wide policy that options depending on EXPERIMENTAL should
also have '(EXPERIMENTAL)' in their option text, and options with
'(EXPERIMENTAL)' depend on EXPERIMENTAL.
Ensure that all ARM options comply with this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When CONFIG_ZBOOT_ROM is selected, the resulting zImage file will be small
boot loader and may be burned to rom or flash.
This is the board-specific portion of this patch-set.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When CONFIG_ZBOOT_ROM is selected, the resulting zImage file will be small
boot loader and may be burned to rom or flash.
This is the non-board-specific framework portion of this patch-set.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As our SMP implementation uses MESI protocols. Grouping together data
which is mostly only read together means that we avoid unnecessary
cache line bouncing when this code shares a cache line with other data.
In other words, cache lines associated with read-mostly data are
expected to spend most of their time in shared state.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Today more boards with arm cpu have selectable pci bus.
This patch makes this more scalable and remove line continuations in
Kconfig
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The generic conversion eliminates the spurious no_ack and no_end
routines, converts all the cascaded handlers to handle_simple_irq() and
makes iosapic use a modified handle_percpu_irq() to become the same as
the CPU irq's. This isn't an essential change, but it eliminates the
mask/unmask overhead of handle_level_irq().
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Tested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
The essential problem we're currently having is that dino (and gsc) is a
cascaded CPU interrupt. Under the old __do_IRQ() handler, our CPU
interrupts basically did an ack followed by an end. In the new scheme,
we replaced them with level handlers which do a mask, an ack and then an
unmask (but no end). Instead, with the renaming of end to eoi, we
actually want to call the percpu flow handlers, because they actually
have all the characteristics we want.
This patch does the conversion and gets my C360 booting again.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Include sched.h to ensure sched_clock() has the notrace
annotation, and mark any functions it calls as notrace
too.
Include sched.h to ensure sched_clock() has the notrace
annotation, and mark any functions it calls as notrace
too.
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Depending on the compiler version, ARM GCC calls the mcount function
either __gnu_mcount_nc or mcount.
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
For kernels built with PREEMPT_RT, critical sections protected
by standard spinlocks are preemptible. This is not acceptable
on perf as (a) we may be scheduled onto a different CPU whilst
reading/writing banked PMU registers and (b) the latency when
reading the PMU registers becomes unpredictable.
This patch upgrades the pmu_lock spinlock to a raw_spinlock
instead.
Reported-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell reported a number of warnings coming from sparse when
checking the ARM perf_event.c files:
| perf_event.c seems to also have problems too:
|
| CHECK arch/arm/kernel/perf_event.c
| arch/arm/kernel/perf_event.c:37:1: warning: symbol 'pmu_lock' was not declared. Should it be static?
| arch/arm/kernel/perf_event.c:70:1: warning: symbol 'cpu_hw_events' was not declared. Should it be static?
| arch/arm/kernel/perf_event.c:1006:1: warning: symbol 'armv6pmu_enable_event' was not declared. Should it be static?
| arch/arm/kernel/perf_event.c:1113:1: warning: symbol 'armv6pmu_stop' was not declared. Should it be static?
| arch/arm/kernel/perf_event.c:1956:6: warning: symbol 'armv7pmu_enable_event' was not declared. Should it be static?
| arch/arm/kernel/perf_event.c:3072:14: warning: incorrect type in argument 1 (different address spaces)
| arch/arm/kernel/perf_event.c:3072:14: expected void const volatile [noderef] <asn:1>*<noident>
| arch/arm/kernel/perf_event.c:3072:14: got struct frame_tail *tail
| arch/arm/kernel/perf_event.c:3074:49: warning: incorrect type in argument 2 (different address spaces)
| arch/arm/kernel/perf_event.c:3074:49: expected void const [noderef] <asn:1>*from
| arch/arm/kernel/perf_event.c:3074:49: got struct frame_tail *tail
This patch resolves these issues so we can live in silence
again.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When kexec is used to start a crash kernel the other cores
are notified. These non-crashing cores will save their state
in the crash notes and then do nothing.
Signed-off-by: Per Fransson <per.xx.fransson@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The existing code invokes the syscall with rubbish in r7,
due to what looks like an incorrect literal load idiom.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* Fix kexec build failure with CONFIG_THUMB2_KERNEL.
* Avoids deprecated/forbidden sp and pc usage in for ARMv7
onwards, retaining compatibility with older architecture
versions.
* The pc value saved to newregs is now aligned on a predictable
instruction boundary.
(stmia { ... pc } or str pc has implementation-defined results
in most versions of the ARM architecutre, and is prohibited
(unpredictable) in Thumb-2.)
* Switch to named inline asm arguments (else I get readily
confused ...)
The resulting code should be compatible with all architecture
versions >= v3, with or without CONFIG_THUMB2_KERNEL.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Tested-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently, the inline asm is passed &newregs->ARM_r0 as in input,
when modifying multiple fields of newregs.
It's plausible to assume that GCC will assume newregs->ARM_r0 is
modified when passed the address, but unfortunately this assumption
is incorrect.
Also, GCC has no way to guess that the other ARM_r* fields are
modified without the addition of a "memory" clobber.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'sh/ehci' of master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Convert to USB_ARCH_HAS_OHCI/EHCI selects.
usb: ehci-sh: Add missing ehci helpers.
usb: ehci-sh: Fix up fault in shutdown path.
sh: Add EHCI support for SH7786.
usb: ehci-hcd: Add support for SuperH EHCI.
usb: ohci-sh: Set IRQ as shared.
* '2.6.37-rc4-pvhvm-fixes' of git://xenbits.xen.org/people/sstabellini/linux-pvhvm:
xen: unplug the emulated devices at resume time
xen: fix save/restore for PV on HVM guests with pirq remapping
xen: resume the pv console for hvm guests too
xen: fix MSI setup and teardown for PV on HVM guests
xen: use PHYSDEVOP_get_free_pirq to implement find_unbound_pirq
The MACH_MINI2440 entry requires the backlight LED driver, but this
subsystem has not been enabled and the select of LEDS_TRIGGER_BACKLIGHT
alone is insufficient to enable the necessary bits of the LED driver.
Add NEW_LEDS, LEDS_CLASS and LEDS_TRIGGER to the select to allow the
kernel to link.
This fixes the following error:
drivers/built-in.o: In function `led_trigger_set':
/home/ben/linux.git/drivers/leds/led-triggers.c:116: undefined reference to `led_brightness_set'
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'upstream/core' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
xen: allocate irq descs on any NUMA node
xen: prevent crashes with non-HIGHMEM 32-bit kernels with largeish memory
xen: use default_idle
xen: clean up "extra" memory handling some more
* 'upstream/bugfix' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
xen: x86/32: perform initial startup on initial_page_table
xen: don't bother to stop other cpus on shutdown/reboot
* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: se/7724: Remove FSI/B of GPIO init code
sh: se/7724: Update clock framework of FSI clock to non-legacy
sh: Assume new page cache pages have dirty dcache lines.
sh: boards: mach-se: use IS_ERR() instead of NULL check
sh: Add div6_reparent_clks to clock framework for FSI
dma: shdma: add a MODULE_ALIAS() to allow module autoloading
Implement asm/syscall.h for the MN10300 arch.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, to define a GPIO number, we're using something like :
#define EFIKAMX_PCBID0 (2*32 + 16)
to define GPIO 3 16.
This is not really readable and it's error prone imho (note the 3 vs 2).
So, I'm introducing a new macro to define this in a better way. Now, the
code sample become :
#define EFIKAMX_PCBID0 IMX_GPIO_NR(3, 16)
v2:
- move to gpio.h
- add parens & spaces
- switch to IMX_GPIO_NR instead of MX51_GPIO_NR
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Amit Kucheria <amit.kucheria@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Commit 124bf94a "ARM: imx: fix name for functions adding sdhci-esdhc-imx devices"
changed some devices and Kconfig entry and didn't change every places
it should have. It's breaking efikamx build. I've fixed 3ds Kconfig
entry as I believe it's broken there too.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In commit 2c20b9f (ARM: mx25: dynamically allocate mxc-ehci devices) I
changed the offset to the value specified in the reference manual
intending to test this change on hardware. This slipped through and now
prooved to be wrong. So fix it and add a comment about the
documentation being wrong.
Reported-by: Jaume Ribot <jaume@fqingenieria.es>
Cc: Michael Trimarchi <trimarchi@gandalf.sssup.it>
Cc: Shawn Guo <shawn.gsc@gmail.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
commits 2eb42d5c28 and
9e1dde3387 renamed some defines
but didn't fix all the places where these defines are used
leading to a compile failure for USB on i.MX31, 35 and 27.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The SDMA firmware consists of a ROM part and a RAM part.
The ROM part is always present in the SDMA engine and
is sufficient for many cases.
This patch allows to pass in platform data containing
the script addresses in ROM, so loading a firmware is
optional now.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
As we've now removed the spinlock and bitmask, we have nothing left
which requires interrupts to be disabled when sending an IPI. All
current IPI-sending implementations use the GIC, which also does not
require interrupts disabled when calling gic_raise_softirq().
Remove the now unnecessary IRQ disable.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Avoid using bitmasks and locks in the percpu area for IPIs, and instead
use individual software generated interrupts to identify the reason for
the IPI. This avoids the problems of having spinlocks in the percpu
area.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This allows us to use smp_cross_call() to trigger a number of different
software generated interrupts, rather than combining them all on one
SGI. Recover the SGI number via do_IPI.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
smp_cross_call_done() was removed long ago (see 78d236c - remove useless
smp_cross_call_done()). Remove those which have been subsequently
merged.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch improves the state of the AG5 clock
framework support. The main clock parent is
automatically detected, but most of the clocks
are not used by any driver or subsystem at this
point. More work is needed for support of multi
media hardware such as FSI and/or LCDC/MIPI-DSI.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Wakeup-on-timer code does not have/need debugfs dependency. Move
the function out of debugfs ifdef.
Fixes compile error when CONFIG_DEBUG_FS is disabled but PM debug is
enabled.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When OneNAND support is disabled, the platform code defines NULL
board_onenand_data and empty init function for us. By utilizing this we
can avoid cluttering board files with dummy definitions/wrappers.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When OneNAND support is disabled, the platform code defines NULL
board_onenand_data and empty init function for us. By utilizing this we
can avoid cluttering board files with dummy definitions/wrappers.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If CONFIG_OMAP_MUX is not enabled, we can define board_mux in the header
file instead of forcing every single board to define it.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
[tony@atomide.com: updated for combined board-zoom files]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Boot to boot the TSC calibration may vary by quite a large amount.
While normal variance of 50-100ppm can easily be seen, the quick
calibration code only requires 500ppm accuracy, which is the limit
of what NTP can correct for.
This can cause problems for systems being used as NTP servers, as
every time they reboot it can take hours for them to calculate the
new drift error caused by the calibration.
The classic trade-off here is calibration accuracy vs slow boot times,
as during the calibration nothing else can run.
This patch uses a delayed workqueue to calibrate the TSC over the
period of a second. This allows very accurate calibration (in my
tests only varying by 1khz or 0.4ppm boot to boot). Additionally this
refined calibration step does not block the boot process, and only
delays the TSC clocksoure registration by a few seconds in early boot.
If the refined calibration strays 1% from the early boot calibration
value, the system will fall back to already calculated early boot
calibration.
Credit to Andi Kleen who suggested using a timer quite awhile back,
but I dismissed it thinking the timer calibration would be done after
the clocksource was registered (which would break things). Forgive
me for my short-sightedness.
This patch has worked very well in my testing, but TSC hardware is
quite varied so it would probably be good to get some extended
testing, possibly pushing inclusion out to 2.6.39.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <1289003985-29060-1-git-send-email-johnstul@us.ibm.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Ingo Molnar <mingo@elte.hu>
CC: Martin Schwidefsky <schwidefsky@de.ibm.com>
CC: Clark Williams <williams@redhat.com>
CC: Andi Kleen <andi@firstfloor.org>
On stock 2.6.37-rc4, running:
# mount lilith:/export /mnt/lilith
# find /mnt/lilith/ -type f -print0 | xargs -0 file
crashes the machine fairly quickly under Xen. Often it results in oops
messages, but the couple of times I tried just now, it just hung quietly
and made Xen print some rude messages:
(XEN) mm.c:2389:d80 Bad type (saw 7400000000000001 != exp
3000000000000000) for mfn 1d7058 (pfn 18fa7)
(XEN) mm.c:964:d80 Attempt to create linear p.t. with write perms
(XEN) mm.c:2389:d80 Bad type (saw 7400000000000010 != exp
1000000000000000) for mfn 1d2e04 (pfn 1d1fb)
(XEN) mm.c:2965:d80 Error while pinning mfn 1d2e04
Which means the domain tried to map a pagetable page RW, which would
allow it to map arbitrary memory, so Xen stopped it. This is because
vm_unmap_ram() left some pages mapped in the vmalloc area after NFS had
finished with them, and those pages got recycled as pagetable pages
while still having these RW aliases.
Removing those mappings immediately removes the Xen-visible aliases, and
so it has no problem with those pages being reused as pagetable pages.
Deferring the TLB flush doesn't upset Xen because it can flush the TLB
itself as needed to maintain its invariants.
When unmapping a region in the vmalloc space, clear the ptes
immediately. There's no point in deferring this because there's no
amortization benefit.
The TLBs are left dirty, and they are flushed lazily to amortize the
cost of the IPIs.
This specific motivation for this patch is an oops-causing regression
since 2.6.36 when using NFS under Xen, triggered by the NFS client's use
of vm_map_ram() introduced in 56e4ebf877 ("NFS: readdir with vmapped
pages") . XFS also uses vm_map_ram() and could cause similar problems.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Bryan Schumaker <bjschuma@netapp.com>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Alex Elder <aelder@sgi.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When remapping MSIs into pirqs for PV on HVM guests, qemu is responsible
for doing the actual mapping and unmapping.
We only give qemu the desired pirq number when we ask to do the mapping
the first time, after that we should be reading back the pirq number
from qemu every time we want to re-enable the MSI.
This fixes a bug in xen_hvm_setup_msi_irqs that manifests itself when
trying to enable the same MSI for the second time: the old MSI to pirq
mapping is still valid at this point but xen_hvm_setup_msi_irqs would
try to assign a new pirq anyway.
A simple way to reproduce this bug is to assign an MSI capable network
card to a PV on HVM guest, if the user brings down the corresponding
ethernet interface and up again, Linux would fail to enable MSIs on the
device.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Fix the mailbox detection for OMAP3630 and 2430, also minor
cleanup on conditional ifdef's that could affect it.
Given that 2430 has an iva too, include it, as the same steps
for omap3 apply.
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Acked-by: Hiroshi Doyu <hiroshi.doyu@nokia.com>
In the current mailbox driver, the mailbox internal pointer for
callback can be directly manipulated by the Users, so a second
User can easily corrupt the first user's callback pointer.
The initial effort to correct this issue can be referred here:
https://patchwork.kernel.org/patch/107520/
Along with fixing the above stated issue, this patch adds the
flexibility option to register notifications from
multiple readers to the events received on a mailbox instance.
The discussion regarding this can be referred here.
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg30671.html
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: Fernando Guzman Lugo <x0095840@ti.com>
Acked-by: Hiroshi Doyu <hiroshi.doyu@nokia.com>
Schedule the Tasklet to send only when mailbox fifo is full and there are
pending messages in kfifo, else send the message directly in the Process
context. This would avoid needless scheduling of Tasklet for every message
transfer
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Acked-by: Hiroshi Doyu <hiroshi.doyu@nokia.com>
Fix the following checkpatch warnings observed in mailbox module.
WARNING: please, no space for starting a line,
excluding comments
+ fail_alloc_rxq:$
WARNING: please, no space for starting a line,
excluding comments
+ fail_alloc_txq:$
WARNING: please, no space for starting a line,
excluding comments
+ fail_request_irq:$
WARNING: line over 80 characters
+ mbox_kfifo_size = max_t(unsigned int, mbox_kfifo_size, sizeof(mbox_msg_t));
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Acked-by: Hiroshi Doyu <hiroshi.doyu@nokia.com>
The variable rq_full flag is a global variable, so if there are multiple
mailbox users there will be conflicts. Now there is a full flag per
mailbox queue.
Reported-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Fernando Guzman Lugo <x0095840@ti.com>
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Acked-by: Hiroshi Doyu <hiroshi.doyu@nokia.com>
The PXA-SPI driver relies on some files / defines which are arm specific
and are within the ARM tree. The CE4100 SoC which is x86 has also the
SPI core.
This patch moves the ssp and spi files from arm/mach-pxa and plat-pxa to
include/linux where the CE4100 can access them.
This move got verified by building the following defconfigs:
cm_x2xx_defconfig corgi_defconfig em_x270_defconfig ezx_defconfig
imote2_defconfig pxa3xx_defconfig spitz_defconfig zeus_defconfig
raumfeld_defconfig magician_defconfig
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
If a section is not marked with SHF_ALLOC, it will be discarded
by the module code. Therefore, it is not correct to register
the unwind tables.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's no need to keep pointers to the ELF sections available while
the module is loaded - we only need the section pointers while we're
finding and registering the unwind tables, which can all be done during
the finalize stage of loading.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fixes the same problem as described in the patch "nohz: fix
printk_needs_cpu() return value on offline cpus" for the arch_needs_cpu()
primitive:
arch_needs_cpu() may return 1 if called on offline cpus. When a cpu gets
offlined it schedules the idle process which, before killing its own cpu,
will call tick_nohz_stop_sched_tick().
That function in turn will call arch_needs_cpu() in order to check if the
local tick can be disabled. On offline cpus this function should naturally
return 0 since regardless if the tick gets disabled or not the cpu will be
dead short after. That is besides the fact that __cpu_disable() should already
have made sure that no interrupts on the offlined cpu will be delivered anyway.
In this case it prevents tick_nohz_stop_sched_tick() to call
select_nohz_load_balancer(). No idea if that really is a problem. However what
made me debug this is that on 2.6.32 the function get_nohz_load_balancer() is
used within __mod_timer() to select a cpu on which a timer gets enqueued.
If arch_needs_cpu() returns 1 then the nohz_load_balancer cpu doesn't get
updated when a cpu gets offlined. It may contain the cpu number of an offline
cpu. In turn timers get enqueued on an offline cpu and not very surprisingly
they never expire and cause system hangs.
This has been observed 2.6.32 kernels. On current kernels __mod_timer() uses
get_nohz_timer_target() which doesn't have that problem. However there might
be other problems because of the too early exit tick_nohz_stop_sched_tick()
in case a cpu goes offline.
This specific bug was indrocuded with 3c5d92a0 "nohz: Introduce
arch_needs_cpu".
In this case a cpu hotplug notifier is used to fix the issue in order to keep
the normal/fast path small. All we need to do is to clear the condition that
makes arch_needs_cpu() return 1 since it is just a performance improvement
which is supposed to keep the local tick running for a short period if a cpu
goes idle. Nothing special needs to be done except for clearing the condition.
Cc: stable@kernel.org
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Soon resource data will get automatically
populated from a set of autogenerated data
from TI's hardware database for the OMAP
platform.
Such database, might not have resources at
the expected order by the current drivers.
While we could hack in some exceptions to
that tool to generate resources in a specific
order, it seems less fragile to use the
resource name instead. That way, no matter
what order the resources are generated, the
driver still work.
Modified the OMAP, Blackfin and Davinci
architecture files to add the name of the IRQs
in the resource structures and musb driver to
use the platform_get_irq_byname() api to get
the device and dma irq numbers instead of using
the index.
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This switches over to selects for the subtypes to enable OHCI/EHCI
support explicitly rather than littering the usb Kconfig with subtype
dependencies.
Suggested-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
you can control it by
echo 0 > /sys/class/leds/led0/brightness
echo 1 > /sys/class/leds/led0/brightness
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the ARM change c01778001a
("ARM: 6379/1: Assume new page cache pages have dirty D-cache") for the
same rationale:
There are places in Linux where writes to newly allocated page
cache pages happen without a subsequent call to flush_dcache_page()
(several PIO drivers including USB HCD). This patch changes the
meaning of PG_arch_1 to be PG_dcache_clean and always flush the
D-cache for a newly mapped page in update_mmu_cache().
This addresses issues seen with executing binaries from MMC, in
addition to some of the other HCDs that don't explicitly do cache
management for their pipe-in buffers.
Requested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
sparc64 systems have a restriction in that passing in buffer
addressses above 4GB to prom calls is not reliable.
We end up violating this when we do prom console writes, because we
use an on-stack buffer to translate '\n' into '\r\n'.
So instead, do this translation into an intermediate buffer, which is
in the kernel image and thus below 4GB, then pass that to the PROM
console write calls.
On the 32-bit side we don't have to deal with any of these issues, so
the new prom_console_write_buf() uses the existing prom_nbputchar()
implementation. However we can now mark those routines static.
Since the 64-bit side completely uses new code we can delete the
putchar bits as they are now completely unused.
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some unneeded assignments and messages, restructure
a failure path in iova_to_phys, and make __flush_iotlb
return int in preparation for adding IOMMU clock control.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Add support for allowing IOMMU memory transactions to be
cache coherent, eliminating the need for software cache
management in certain situations. This can lead to
improvements in performance and power usage, assuming the
multimedia core's access pattern exhibits spatial locality
and that its working set fits into the cache.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Add the register field definitions and memory attribute
definitions that will be needed to support IOMMU
transactions with cache-coherent memory access.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Make the IOMMU driver select the IOMMU API in the kernel
configuration.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
An IOMMU device can only be attached to one IOMMU domain at
any given time. Check whether the device is already
attached to a domain before allowing it to be attached to
another domain. If so, return busy.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Add a Kconfig item to allow the IOMMU page tables to be
coherent in the L2 cache. This generally reduces IOTLB miss
latencies and has been shown to improve multimedia
performance.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Paul Walmsley
Raghuveer Murthy
Thomas Weber
Daniel Morsing
Tony Lindgren
Jean Pihet
Eduardo Valentin
Nishanth Menon
Peter 'p2' De Schrijver
Richard Woodruff
Kevin Hilman
Thara Gopinath
Adrian Hunter
Yauhen Kharuzhy
David Brown
Marcelo Roberto Jimenez
Jarkko Nikula
Grazvydas Ignotas
Hemanth V
Laurent Pinchart
Marc Zyngier
Anand Gadiyar
Srikar
Aaro Koskinen
G, Manjunath Kondaiah
Benoit Cousson
Marek Belisko
Linus Torvalds
Nicolas Pitre
Russell King
Shawn Guo
Paul Mundt
Magnus Damm
Yusuke Goda
Marek Vasut
Dave Martin
Bjorn Forsman
Mark F. Brown
Eric Miao
Haojian Zhuang
Vincent Guittot
Jonas Aaberg
Sundar Iyer
Nicolas Pitre
Ingo Molnar
Robert Richter
Santosh Shilimkar
Mans Rullgard
Tejun Heo
Christoph Lameter
John Rigby
Bryan Wu
Ohad Ben-Cohen
Jean Pihet
H. Peter Anvin
Chris Metcalf
Kevin Cernekee
Bjorn Helgaas
Christian Glindkamp
Ryan Mallon
Marek Szyprowski
Yauhen Kharuzhy
Kukjin Kim
Werner Fink
Pavankumar Kondeti
David Daney
Maciej W. Rozycki
Manuel Lauss
Ralf Baechle
Hauke Mehrtens
Thomas Chou
Lars-Peter Clausen
Tony Wu
Florian Fainelli
Yoichi Yuasa
Wu Zhangjin
Jesper Juhl
Al Viro
Greg Kroah-Hartman
Avi Kivity
Peter Zijlstra
Rusty Russell
cxie4
Daniel Mack
Zhangfei Gao
Lennert Buytenhek
Daniel Walker
Stepan Moskovchenko
Felipe Contreras
Guzman Lugo, Fernando
Mike Rapoport
Sascha Hauer
Will Deacon
Randy Dunlap
Lothar Waßmann
Valentine Barshak
Carmelo AMOROSO
Fabio Estevam
Arnaud Patard (Rtp)
Peter Horton
Kenji Kaneshige
Suresh Siddha
Don Zickus
Thomas Gleixner
Tony SIM
Catalin Marinas
David S. Miller
Julian Calaby
Sergei Shtylyov
Einar Lueck
Ben Gardiner
Nicolas Kaiser
Cyril Chemparathy
Andreas Gaeer
Hema HK
Ajay Kumar Gupta
Felipe Balbi
Feng Tang
Yinghai Lu
Rakib Mullick
Martin Persson
Andre Przywara
Joerg Roedel
Sheng Yang
Rabin Vincent
Carl-Johan Irekvist
Per Forlin
Linus Walleij
Mattias Wallin
Vasily Khoruzhick
Varadarajan, Charulatha
Shubhrajyoti D
Evgeny Kuznetsov
David Howells
Martin Michlmayr
Ash Hughes
Magnus Damm
Olof Johansson
Vasiliy Kulikov
Masami Hiramatsu
Dirk Brandewie
Sebastian Andrzej Siewior
Chao Xie
Kuninori Morimoto
Hans Ulli Kroll
James Bottomley
Rabin Vincent
Per Fransson
Ben Dooks
Uwe Kleine-König
Eric Bénard
Nobuhiro Iwamatsu
John Stultz
John Stultz
Jeremy Fitzhardinge
Stefano Stabellini
Omar Ramirez Luna
Kanigeri, Hari
Heiko Carstens