The DMADISABLE bit is a semi-automatic bit present in sysconfig register
of some modules. When the DMA must perform read/write accesses, the
DMADISABLE bit is cleared by the hardware. But when the DMA must stop for power
management, software must set the DMADISABLE bit back to 1.
In cases where the ROMCODE/BOOTLOADER uses dma, the hardware clears the
DMADISABLE bit (but the romcode/bootloader might not set it back to 1).
In order for the kernel to start in a clean state, it is
necessary for the kernel to set DMADISABLE bit back to 1 (irrespective
of whether it's been set to 1 in romcode or bootloader).
During _reset of the (hwmod)device, the DMADISABLE bit is set so that it
does not prevent idling of the system. (NOTE: having DMADISABLE to 0,
prevents the system to idle)
DMADISABLE bit is present in usbotgss module of omap5.
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[paul@pwsan.com: updated to apply; fixed checkpatch warnings]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add an API to get main clock name associated with a given @oh.
This will avoid the need to construct fclk names during early
initialization in order to get fclk handle using clk_get().
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In case of AM33XX device, XXX_RSTST register offset is not
consistent across PRM modules/instances,
PRM_XXX RSTST
=========================
PRM_PER_MOD: 0x04
PRM_WKUP_MOD: 0x0C
PRM_MPU_MOD: NA
PRM_DEVICE_MOD: 0x08
This means, we need to pass on XXX_RSTST register offset
information through omap_hwmod data, similar to XXX_RSTCTRL.
Currently, this field is only applicable and used for AM33XX
devices.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In case of AM33xx family of devices (like cpsw) have different sysc
bit field offsets defined,
sysc_type3:
| 3 2 | 1 0 |
| STDBYMODE | IDLEMODE |
So introduce new sysc_type3 in omap_hwmod common data.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
hwmod, clock, and System Control Module cleanup, and the removal
of the last instance of omap_read/write usage for omap2+ with
the removal of unused USB OHCI Full Speed driver support. The
removed OHCI is only currently used for omap1 as the actively
used omap2+ boards have either MUSB or another instance of
OHCI+EHCI that's more usable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=A9qD
-----END PGP SIGNATURE-----
mergetag object c59b537d87
type commit
tag omap-devel-dmtimer-for-v3.6
tagger Tony Lindgren <tony@atomide.com> 1341130362 -0700
Here are some omap dmtimer changes to make it easier to add
device tree support for dmtimer by simplifying the platform
data structure used by dmtimr.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=L0+0
-----END PGP SIGNATURE-----
mergetag object 6fd8246b1c
type commit
tag omap-devel-am33xx-for-v3.6
tagger Tony Lindgren <tony@atomide.com> 1341131157 -0700
Here are changes to add support for am33xx processors for the
clock, power, and voltagedomains.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=bc0b
-----END PGP SIGNATURE-----
Merge tags 'omap-cleanup-for-v3.6', 'omap-devel-dmtimer-for-v3.6' and 'omap-devel-am33xx-for-v3.6' into devel-am33xx-part2
device tree support for dmtimer by simplifying the platform
data structure used by dmtimr.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=L0+0
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-dmtimer-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/timer
From Tony Lindgren <tony@atomide.com>:
Here are some omap dmtimer changes to make it easier to add
device tree support for dmtimer by simplifying the platform
data structure used by dmtimr.
* tag 'omap-devel-dmtimer-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Simplify dmtimer clock aliases
ARM: OMAP2+: Move dmtimer clock set function to dmtimer driver
ARM: OMAP1: Fix dmtimer support
ARM: OMAP: Add flag to indicate if a timer needs a manual reset
ARM: OMAP: Remove timer function pointer for context loss counter
ARM: OMAP: Remove loses_context variable from timer platform data
ARM: OMAP2+: Fix external clock support for dmtimers
ARM: OMAP2+: HWMOD: Correct timer device attributes
ARM: OMAP: Add DMTIMER capability variable to represent timer features
ARM: OMAP2+: Add dmtimer platform function to reserve systimers
ARM: OMAP2+: Remove unused max number of timers definition
ARM: OMAP: Remove unnecessary clk structure
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
AM33XX clock implementation is different than any existing OMAP
family of devices. Although DPLL module is similar to OMAP4
device, but the usage is very much different than OMAP4.
AM33XX has different peripheral set and each module gets
integrated to the clock framework differently than OMAP
family of devices.
This patch adds full Clock tree data for AM33XX family
of devices and also integrates it into existing OMAP framework.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
CC: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: updated to apply; changed 'soc_is_am33xx' to
'cpu_is_am33xx' to match usage in Tony's current am33xx branch]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The powerdomain and clockdomain data for the AM35xx are finally fixed.
The AM35xx EMAC/MDIO Ethernet controller integration code has been
converted to use the OMAP device and hwmod framework. Also the UART4
and HSOTGUSB warnings have been fixed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=2b0z
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-d-for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes-non-critical
Some OMAP AM35xx fixes.
The powerdomain and clockdomain data for the AM35xx are finally fixed.
The AM35xx EMAC/MDIO Ethernet controller integration code has been
converted to use the OMAP device and hwmod framework. Also the UART4
and HSOTGUSB warnings have been fixed.
Now that OMAP730 and OMAP850 support is mostly unified, there's no
need for separate cpu detection macros for these architectures. At
least, currently there isn't, because both macros are unused.
cpu_is_7xx() seems to cover all possible uses.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
[tony@atomide.com: updated to also to remove related IS_OMAP_TYPE]
Signed-off-by: Tony Lindgren <tony@atomide.com>
No file includes omap730.h or omap850.h. That's not surprising, as
commit e6684f7132 ("OMAP7XX: Create
omap7xx.h") created a header that was "intended to replace omap730.h and
omap850.h", while all "values defined [in omap7xx.h] are identical to
those in both the old files". So it seems it was just an oversight to
keep both the old files after commit
7a8f48f8c6 ("OMAP7XX: omap_uwire.c:
Convert to omap7xx.h") converted the last file still including one of
those two old files.
Convert the last reference to omap730.h to a reference to omap7xx.h too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Provide an interface for a driver to call SCM functions to
set a boot address and boot mode.
Signed-off-by: Omar Ramirez Luna <omar.luna@linaro.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
There are certain fields inside 'struct dpll_data' which are
included under ARCH_OMAP3 and ARCH_OMAP4 option, which makes it
difficult to use it for new devices like, am33xx, ti81xx, etc...
So remove the ifdef completely, this will add few fields to the struct
unused, but it improves readability and maintainability of the code.
Signed-off-by: Kevin Hilman <khilman@ti.com>
[hvaibhav@ti.com: wrote detailed changelog]
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: R Sricharan <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The enable/disable module functions are specific to SoCs with
OMAP4-class PRCM. Rather than use cpu_is* checks at runtime inside
the enable/disable module functions, use cpu_is at init time to
initialize function pointers only for SoCs that need them.
NOTE: the cpu_is* check for _enable_module was different than
the one for _disable_module, and this patch uses
cpu_is_omap44xx() for both.
Signed-off-by: Kevin Hilman <khilman@ti.com>
[paul@pwsan.com: moved soc_ops function pointers to be per-kernel rather than
per-hwmod since they do not vary by hwmod; added kerneldoc]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP1 uses an architecture specific function for setting the dmtimer clock
source, where as the OMAP2+ devices use the clock framework. Eventually OMAP1
device should also use the clock framework and hence we should not any
architecture specific functions.
For now move the OMAP2+ function for configuring the clock source into the
dmtimer driver. Therefore, we do no longer need to specify an architecture
specific function for setting the clock source for OMAP2+ devices. This will
simplify device tree migration of the dmtimers for OMAP2+ devices.
From now on, only OMAP1 devices should specify an architecture specific
function for setting the clock source via the platform data set_dmtimer_src()
function pointer.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For OMAP1 devices, it is necessary to perform a manual reset of the timer.
Currently, this is indicating by setting the "needs_manual_reset" variable in
the platform data. Instead of using an extra variable to indicate this add a new
timer capabilities flag to indicate this and remove the "needs_manual_reset"
member from the platform data.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For OMAP2+ devices, a function pointer that returns the number of times a timer
power domain has lost context is passed to the dmtimer driver. This function
pointer is only populated for OMAP2+ devices and it is pointing to a platform
function. Given that this is a platform function, we can simplify the code by
removing the function pointer and referencing the function directly. We can use
the OMAP_TIMER_ALWON flag to determine if we need to call this function for
OMAP1 and OMAP2+ devices.
The benefit of this change is the we can remove the function pointer from the
platform data and simplifies the dmtimer migration to device-tree.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The platform data variable loses_context is used to determine if the timer may
lose its logic state during power transitions and so needs to be restored. This
information is also provided in the HWMOD device attributes for OMAP2+ devices
via the OMAP_TIMER_ALWON flag. When this flag is set the timer will not lose
context. So use the HWMOD device attributes to determine this.
For OMAP1 devices, loses_context is never set and so set the OMAP_TIMER_ALWON
flag for OMAP1 timers to ensure that code is equivalent.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently, the dmtimer determines whether an timer can support an external
clock source (sys_altclk) for driving the timer by the IP version. Only
OMAP24xx devices can support an external clock source, but the IP version
between OMAP24xx and OMAP3xxx is common and so this incorrectly indicates
that OMAP3 devices can use an external clock source.
Rather than use the IP version, just let the clock framework handle this.
If the "alt_ck" does not exist for a timer then the clock framework will fail
to find the clock and hence will return an error. By doing this we can eliminate
the "timer_ip_version" variable passed as part of the platform data and simplify
the code.
We can also remove the timer IP version from the HWMOD data because the dmtimer
driver uses the TIDR register to determine the IP version.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Although the OMAP timers share a common hardware design, there are some
differences between the timer instances in a given device. For example, a timer
maybe in a power domain that can be powered-of, so can lose its logic state and
need restoring where as another may be in power domain that is always be on.
Another example, is a timer may support different clock sources to drive the
timer. This information is passed to the dmtimer via the following platform data
structure.
struct dmtimer_platform_data {
int (*set_timer_src)(struct platform_device *pdev, int source);
int timer_ip_version;
u32 needs_manual_reset:1;
bool loses_context;
int (*get_context_loss_count)(struct device *dev);
};
The above structure uses multiple variables to represent the timer features.
HWMOD also stores the timer capabilities using a bit-mask that represents the
features supported. By using the same format for representing the timer
features in the platform data as used by HWMOD, we can ...
1. Use the flags defined in the plat/dmtimer.h to represent the features
supported.
2. For devices using HWMOD, we can retrieve the features supported from HWMOD.
3. Eventually, simplify the platform data structure to be ...
struct dmtimer_platform_data {
int (*set_timer_src)(struct platform_device *pdev, int source);
u32 timer_capability;
}
Another benefit from doing this, is that it will simplify the migration of the
dmtimer driver to device-tree. For example, in the current OMAP2+ timer code the
"loses_context" variable is configured at runtime by calling an architecture
specific function. For device tree this creates a problem, because we would need
to call the architecture specific function from within the dmtimer driver.
However, such attributes do not need to be queried at runtime and we can look up
the attributes via HWMOD or device-tree.
This changes a new "capability" variable to the platform data and timer
structure so we can start removing and simplifying the platform data structure.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
During early boot, one or two dmtimers are reserved by the kernel as system
timers (for clocksource and clockevents). These timers are marked as reserved
and the dmtimer driver is notified which timers have been reserved via the
platform data information.
For OMAP2+ devices the timers reserved may vary depending on device and compile
flags. Therefore, it is not easy to assume which timers we be reserved for the
system timers. In order to migrate the dmtimer driver to support device-tree we
need a way to pass the timers reserved for system timers to the dmtimer driver.
Using the platform data structure will not work in the same way as it is
currently used because the platform data structure will be stored statically in
the dmtimer itself and the platform data will be selected via the device-tree
match device function (of_match_device).
There are a couple ways to workaround this. One option is to store the system
timers reserved for the kernel in the device-tree and query them on boot.
The downside of this approach is that it adds some delay to parse the DT blob
to search for the system timers. Secondly, for OMAP3 devices we have a
dependency on compile time flags and the device-tree would not be aware of that
kernel compile flags and so we would need to address that.
The second option is to add a function to the dmtimer code to reserved the
system timers during boot and so the dmtimer knows exactly which timers are
being used for system timers. This also allows us to remove the "reserved"
member from the timer platform data. This seemed like the simpler approach and
so was implemented here.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In the plat/dmtimer.h there is a structure named "clk" declared. This structure
is not used and appears to be left over from previous code. Hence, remove this
unused structure.
Verified that both omap1 and omap2plus kernel configurations build with this
change.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If CONFIG_MMC_OMAP is not set and CONFIG_MMC_OMAP_HS is set,
we can get error: redefinition of `omap242x_init_mmc' error.
Fix it by removing MMC_OMAP_HS from MMC_OMAP ifdefs as they do
not depend on each other.
While at it, also prettify the formatting a bit.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for low level debugging on AM335X EVM (AM33XX family).
Currently only support for UART1 console, which is used on AM335X EVM
is added.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As the FS USB code is not being actively used for omap2+
there's no point keeping it around for omap2+.
Let's make the FS USB platform init code omap1 only so
we can remove the last user of omap_read/write for omap2+,
and simplify things for further USB, DMA, and device tree
related work.
While at it, also group the mach includes for the related
drivers.
Cc: linux-usb@vger.kernel.org
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Updates to mxc_nand and gpmi drivers to support new boards and device tree
- Improve consistency of information about ECC strength in NAND devices
- Clean up partition handling of plat_nand
- Support NAND drivers without dedicated access to OOB area
- BCH hardware ECC support for OMAP
- Other fixes and cleanups, and a few new device IDs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAk/JG1wACgkQdwG7hYl686M80wCglN4kutx20j+KJWuZofkr9Hog
weEAoI4jrqEWEdW9EcT2CIWQw7eG+1v+
=7tdo
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd
Pull mtd update from David Woodhouse:
- More robust parsing especially of xattr data in JFFS2
- Updates to mxc_nand and gpmi drivers to support new boards and device tree
- Improve consistency of information about ECC strength in NAND devices
- Clean up partition handling of plat_nand
- Support NAND drivers without dedicated access to OOB area
- BCH hardware ECC support for OMAP
- Other fixes and cleanups, and a few new device IDs
Fixed trivial conflict in drivers/mtd/nand/gpmi-nand/gpmi-nand.c due to
added include files next to each other.
* tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd: (75 commits)
mtd: mxc_nand: move ecc strengh setup before nand_scan_tail
mtd: block2mtd: fix recursive call of mtd_writev
mtd: gpmi-nand: define ecc.strength
mtd: of_parts: fix breakage in Kconfig
mtd: nand: fix scan_read_raw_oob
mtd: docg3 fix in-middle of blocks reads
mtd: cfi_cmdset_0002: Slight cleanup of fixup messages
mtd: add fixup for S29NS512P NOR flash.
jffs2: allow to complete xattr integrity check on first GC scan
jffs2: allow to discriminate between recoverable and non-recoverable errors
mtd: nand: omap: add support for hardware BCH ecc
ARM: OMAP3: gpmc: add BCH ecc api and modes
mtd: nand: check the return code of 'read_oob/read_oob_raw'
mtd: nand: remove 'sndcmd' parameter of 'read_oob/read_oob_raw'
mtd: m25p80: Add support for Winbond W25Q80BW
jffs2: get rid of jffs2_sync_super
jffs2: remove unnecessary GC pass on sync
jffs2: remove unnecessary GC pass on umount
jffs2: remove lock_super
mtd: gpmi: add gpmi support for mx6q
...
Move the omap_volt_data structure from mach-omap2/ directory
to arch/arm/plat-omap/include/plat/ so that it is accessible
from both mach-omap2 and drivers directories.
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
More cleanups, continuing an earlier set with omap and samsung specific
cleanups. These could not go into the first set because they have
dependencies on various other series that in turn depend on the first
cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=7UKB
-----END PGP SIGNATURE-----
Merge tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc cleanups (part 2) from Olof Johansson:
"More cleanups, continuing an earlier set with omap and samsung
specific cleanups. These could not go into the first set because they
have dependencies on various other series that in turn depend on the
first cleanups."
Fixed up conflicts in arch/arm/plat-omap/counter_32k.c due to commit
bd0493eaaf5c: "move read_{boot,persistent}_clock to the architecture
level" that changed how the persistent clocks were handled. And trivial
conflicts in arch/arm/mach-omap1/common.h due to just independent
changes close to each other.
* tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (35 commits)
ARM: SAMSUNG: merge plat-s5p into plat-samsung
ARM: SAMSUNG: move options for common s5p into plat-samsung/Kconfig
ARM: SAMSUNG: move setup code for s5p mfc and mipiphy into plat-samsung
ARM: SAMSUNG: move platform device for s5p uart into plat-samsung
ARM: SAMSUNG: move hr timer for common s5p into plat-samsung
ARM: SAMSUNG: move pm part for common s5p into plat-samsung
ARM: SAMSUNG: move interrupt part for common s5p into plat-samsung
ARM: SAMSUNG: move clock part for common s5p into plat-samsung
ARM: S3C24XX: Use common macro to define resources on dev-uart.c
ARM: S3C24XX: move common clock init into common.c
ARM: S3C24XX: move common power-management code to mach-s3c24xx
ARM: S3C24XX: move plat-s3c24xx/dev-uart.c into common.c
ARM: S3C24XX: move plat-s3c24xx/cpu.c
ARM: OMAP2+: Kconfig: convert SOC_OMAPAM33XX to SOC_AM33XX
ARM: OMAP2+: Kconfig: convert SOC_OMAPTI81XX to SOC_TI81XX
GPMC: add ECC control definitions
ARM: OMAP2+: dmtimer: remove redundant sysconfig context restore
ARM: OMAP: AM35xx: convert 3517 detection/flags to AM35xx
ARM: OMAP: AM35xx: remove redunant cpu_is checks for AM3505
ARM: OMAP1: Pass dma request lines in platform data to MMC driver
...
Remove multiple unused cpu_is_omap35xx macros.
In particular, the cpu_is_omap35* macros for 3503, 3515, 3525 are removed
because they are using omap_has_* feature checks and we want to
remove specific feature detection from SoC family detection.
There are no longer any cpu_is_* checks that depend on specific IP
detection.
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Lots of gpio changes, both to core code and drivers. Changes do touch
architecture code to remove the need for separate arm/gpio.h includes
in most architectures. Some new drivers are added, and a number of
gpio drivers are converted to use irq_domains for gpio inputs used as
interrupts. Device tree support has been amended to allow multiple
gpio_chips to use the same device tree node. Remaining changes are
primarily bug fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=U6hj
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull GPIO driver changes from Grant Likely:
"Lots of gpio changes, both to core code and drivers.
Changes do touch architecture code to remove the need for separate
arm/gpio.h includes in most architectures.
Some new drivers are added, and a number of gpio drivers are converted
to use irq_domains for gpio inputs used as interrupts. Device tree
support has been amended to allow multiple gpio_chips to use the same
device tree node.
Remaining changes are primarily bug fixes."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6: (33 commits)
gpio/generic: initialize basic_mmio_gpio shadow variables properly
gpiolib: Remove 'const' from data argument of gpiochip_find()
gpio/rc5t583: add gpio driver for RICOH PMIC RC5T583
gpiolib: quiet gpiochip_add boot message noise
gpio: mpc8xxx: Prevent NULL pointer deref in demux handler
gpio/lpc32xx: Add device tree support
gpio: Adjust of_xlate API to support multiple GPIO chips
gpiolib: Implement devm_gpio_request_one()
gpio-mcp23s08: dbg_show: fix pullup configuration display
Add support for TCA6424A
gpio/omap: (re)fix wakeups on level-triggered GPIOs
gpio/omap: fix broken context restore for non-OFF mode transitions
gpio/omap: fix missing check in *_runtime_suspend()
gpio/omap: remove cpu_is_omapxxxx() checks from *_runtime_resume()
gpio/omap: remove suspend/resume callbacks
gpio/omap: remove retrigger variable in gpio_irq_handler
gpio/omap: remove saved_wakeup field from struct gpio_bank
gpio/omap: remove suspend_wakeup field from struct gpio_bank
gpio/omap: remove saved_fallingdetect, saved_risingdetect
gpio/omap: remove virtual_irq_start variable
...
Conflicts:
drivers/gpio/gpio-samsung.c
Here's the big TTY/serial driver pull request for the 3.5-rc1 merge window.
Nothing major in here, just lots of incremental changes from Alan and
Jiri reworking some tty core things to behave better and to get a more
solid grasp on some of the nasty tty locking issues.
There are a few tty and serial driver updates in here as well.
All of this has been in the linux-next releases for a while with no problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+7rBoACgkQMUfUDdst+ykXsgCfeDKx6ZgLidYy3H40Y2Pt3XEO
TicAn1fcdGwOmMR/mowa+kTA68D/J6i2
=S7tG
-----END PGP SIGNATURE-----
Merge tag 'tty-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY updates from Greg Kroah-Hartman:
"Here's the big TTY/serial driver pull request for the 3.5-rc1 merge
window.
Nothing major in here, just lots of incremental changes from Alan and
Jiri reworking some tty core things to behave better and to get a more
solid grasp on some of the nasty tty locking issues.
There are a few tty and serial driver updates in here as well.
All of this has been in the linux-next releases for a while with no
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'tty-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (115 commits)
serial: bfin_uart: Make MMR access compatible with 32 bits bf609 style controller.
serial: bfin_uart: RTS and CTS MMRs can be either 16-bit width or 32-bit width.
serial: bfin_uart: narrow the reboot condition in DMA tx interrupt
serial: bfin_uart: Adapt bf5xx serial driver to bf60x serial4 controller.
Revert "serial_core: Update buffer overrun statistics."
tty: hvc_xen: NULL dereference on allocation failure
tty: Fix LED error return
tty: Allow uart_register/unregister/register
tty: move global ldisc idle waitqueue to the individual ldisc
serial8250-em: Add DT support
serial8250-em: clk_get() IS_ERR() error handling fix
serial_core: Update buffer overrun statistics.
tty: drop the pty lock during hangup
cris: fix missing tty arg in wait_event_interruptible_tty call
tty/amiserial: Add missing argument for tty_unlock()
tty_lock: Localise the lock
pty: Lock the devpts bits privately
tty_lock: undo the old tty_lock use on the ctty
serial8250-em: Emma Mobile UART driver V2
Add missing call to uart_update_timeout()
...
Power management changes here are mostly for the omap platform, but also
include cpuidle changes for ux500 and suspend/resume code for mmp.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=oGcZ
-----END PGP SIGNATURE-----
Merge tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc power management changes from Olof Johansson:
"Power management changes here are mostly for the omap platform, but
also include cpuidle changes for ux500 and suspend/resume code for
mmp."
* tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
ARM: OMAP2+: WDTIMER integration: fix !PM boot crash, disarm timer after hwmod reset
ARM: OMAP2/3: hwmod data: Add 32k-sync timer data to hwmod database
ARM: OMAP4: hwmod_data: Name the common irq for McBSP ports
ARM: OMAP4: hwmod data: I2C: add flag for context restore
ARM: OMAP3: hwmod_data: Rename the common irq for McBSP ports
ARM: OMAP2xxx: hwmod data: add HDQ/1-wire hwmod
ARM: OMAP3: hwmod data: add HDQ/1-wire hwmod
ARM: OMAP2+: hwmod data: add HDQ/1-wire hwmod shared data
ARM: OMAP2+: HDQ1W: add custom reset function
ARM: OMAP2420: hwmod data: Add MMC hwmod data for 2420
arm: omap3: clockdomain data: Remove superfluous commas from gfx_sgx_3xxx_wkdeps[]
ARM: OMAP2+: powerdomain: Get rid off duplicate pwrdm_clkdm_state_switch() API
ARM: OMAP3: clock data: add clockdomain for HDQ functional clock
ARM: OMAP3+: dpll: Configure autoidle mode only if it's supported
ARM: OMAP2+: dmtimer: cleanup iclk usage
ARM: OMAP4+: Add prm and cm base init function.
ARM: OMAP2/3: Add idle_st bits for ST_32KSYNC timer to prcm-common header
ARM: OMAP3: Fix CM register bit masks
ARM: OMAP: clock: convert AM3517/3505 detection/flags to AM35xx
ARM: OMAP3: clock data: treat all AM35x devices the same
...
These bug fixes were not important enough to have them included in the
v3.4 release, mostly because they cover harmless warnings or unrealistic
configurations. Instead we queue them up to be picked up in the next
merge window.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=yCUM
-----END PGP SIGNATURE-----
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull non-critical arm-soc bug fixes from Olof Johansson:
"These bug fixes were not important enough to have them included in the
v3.4 release, mostly because they cover harmless warnings or
unrealistic configurations. Instead we queue them up to be picked up
in the next merge window."
Fixed up trivial conflict in arch/arm/mach-omap2/board-omap4panda.c
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: spear6xx: remove board selection options
ARM: OMAP: igep0020: Specify the VPLL2 regulator unconditionally
ARM: OMAP2+: INTC: fix Kconfig option for TI81XX
ARM: OMAP2+: remove incorrect irq_chip ack field
ARM: OMAP4: Adding ID for OMAP4460 ES1.1
ARM: OMAP4: panda: add statics to remove warnings
ARM: OMAP2+: Incorrect Register Offsets in OMAP Mailbox
ARM: OMAP: fix trivial warnings for dspbridge
arm: davinci: use for_each_set_bit_from
ARM: OMAP4: hsmmc: check for null pointer
ARM: OMAP1: fix compilation issue in board-sx1.c
ARM: disable SUSPEND/ARCH_SUSPEND_POSSIBLE for ARCH_TEGRA
ARM: davinci: da850-evm: fix section mismatch
ARM: tegra: add pll_x freq table entry for 750MHz
ARM: davinci: mark spi_board_info arguments as const
ARM: davinci: fix incorrect pdctl next bit position
This patch adds a simple BCH ecc computation api, similar to the
existing Hamming ecc api. It is intended to be used by the MTD layer.
It implements the following features:
- support 4-bit and 8-bit ecc computation
- do not protect user bytes in spare area, only data area is protected
- ecc for an erased NAND page (0xFFs) is also a sequence of 0xFFs
This last feature is obtained by adding a constant polynomial to
the hardware computed ecc. It allows to correct bitflips in blank pages
and is extremely useful to support filesystems such as UBIFS, which expect
erased pages to contain only 0xFFs.
This api has been tested on an OMAP3630 board.
Artem: The OMAP maintainer Tony Lindgren gave us his blessing for merging
this patch via the MTD tree.
Signed-off-by: Ivan Djelic <ivan.djelic@parrot.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add register offsets for GPIO_IRQSTATUS_RAW_0, GPIO_IRQSTATUS_RAW_0
which are present on OMAP4+ processors. Now we can distinguish
conditions applicable to OMAP4,5 and those specific to OMAP24xx
and OMAP3xxx.
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=ALlA
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-timer-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup2
Timer changes to make it easier to support various SoCs
By Vaibhav Hiremath
via Tony Lindgren
* tag 'omap-cleanup-timer-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: Make OMAP clocksource source selection using kernel param
ARM: OMAP2+: Replace space with underscore in the name field of system timers
ARM: OMAP1: Add checks for possible error condition in timer_init
except for the RNG driver that will be done later on.
As this depends on omap-devel-hwmod-data-for-v3.5 and causes merge
conflict with omap-fixes-non-critical-for-v3.5, this branch is based
on merge of the two.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=w67p
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-devices-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup2
Changes to split plat-omap/devices.c into mach-omap1 and mach-omap2
except for the RNG driver that will be done later on.
As this depends on omap-devel-hwmod-data-for-v3.5 and causes merge
conflict with omap-fixes-non-critical-for-v3.5, this branch is based
on merge of the two.
By Tony Lindgren (7) and others
via Tony Lindgren (4) and Paul Walmsley (1)
* tag 'omap-cleanup-devices-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (27 commits)
ARM: OMAP1: Pass dma request lines in platform data to MMC driver
ARM: OMAP: Move omap_mmc_add() to mach-omap1
ARM: OMAP2: Use hwmod to initialize mmc for 2420
ARM: OMAP2+: Move omap_dsp_reserve_sdram_memblock() to mach-omap2
ARM: OMAP1: Move omap_init_uwire to mach-omap1
ARM: OMAP1: Move omap_init_audio() to keep the devices in alphabetical order
ARM: OMAP2+: WDTIMER integration: fix !PM boot crash, disarm timer after hwmod reset
ARM: OMAP2/3: hwmod data: Add 32k-sync timer data to hwmod database
ARM: OMAP4: hwmod_data: Name the common irq for McBSP ports
ARM: OMAP4: hwmod data: I2C: add flag for context restore
ARM: OMAP3: hwmod_data: Rename the common irq for McBSP ports
ARM: OMAP2xxx: hwmod data: add HDQ/1-wire hwmod
ARM: OMAP3: hwmod data: add HDQ/1-wire hwmod
ARM: OMAP2+: hwmod data: add HDQ/1-wire hwmod shared data
ARM: OMAP2+: HDQ1W: add custom reset function
ARM: OMAP2420: hwmod data: Add MMC hwmod data for 2420
arm: omap3: clockdomain data: Remove superfluous commas from gfx_sgx_3xxx_wkdeps[]
ARM: OMAP2+: powerdomain: Get rid off duplicate pwrdm_clkdm_state_switch() API
ARM: OMAP3: clock data: add clockdomain for HDQ functional clock
ARM: OMAP3+: dpll: Configure autoidle mode only if it's supported
...
Note that this depends on a fix in omap-fixes-non-critical-for-v3.5,
so it's based on that.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=V8mj
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-renames-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup2
Simplify some SoC config options before things get too unreadable.
Note that this depends on a fix in omap-fixes-non-critical-for-v3.5,
so it's based on that.
By Kevin Hilman (3) and others
via Tony Lindgren
* tag 'omap-cleanup-renames-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Kconfig: convert SOC_OMAPAM33XX to SOC_AM33XX
ARM: OMAP2+: Kconfig: convert SOC_OMAPTI81XX to SOC_TI81XX
ARM: OMAP: igep0020: Specify the VPLL2 regulator unconditionally
ARM: OMAP2+: INTC: fix Kconfig option for TI81XX
ARM: OMAP2+: remove incorrect irq_chip ack field
ARM: OMAP4: Adding ID for OMAP4460 ES1.1
ARM: OMAP4: panda: add statics to remove warnings
ARM: OMAP2+: Incorrect Register Offsets in OMAP Mailbox
ARM: OMAP: fix trivial warnings for dspbridge
ARM: OMAP4: hsmmc: check for null pointer
ARM: OMAP1: fix compilation issue in board-sx1.c
Since hwmod framework now manages sysconfig context save/restore
there is no more need to touch this register in driver. Hence,
remove restore of sysconfig register in omap_timer_restore_context.
This was causing incorrect context restore of sysconfig register.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently cpu_is_omap3517() actually detects any device in the AM35x
family (3517 and no-SGX version 3505.) To make it more clear what is
being detected, convert the names from 3517 to AM35xx.
This adds a new soc_is_am35xx() which duplicates the cpu_is_omap3517().
In order to avoid cross-tree dependencies with clock-tree changes,
cpu_is_omap3517() is left until the clock changes are merged,
at which point cpu_is_omap3517() will be completely removed.
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
[tony@atomide.com: change to use soc_is_omap instead]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Current OMAP code supports couple of clocksource options based
on compilation flag (CONFIG_OMAP_32K_TIMER). The 32KHz sync-timer
and a gptimer which can run on 32KHz or system clock (e.g 38.4 MHz).
So there can be 3 options -
1. 32KHz sync-timer
2. Sys_clock based (e.g 13/19.2/26/38.4 MHz) gptimer
3. 32KHz based gptimer.
The optional gptimer based clocksource was added so that it can
give the high precision than sync-timer, so expected usage was 2
and not 3.
Unfortunately option 2, clocksource doesn't meet the requirement of
free-running clock as per clocksource need. It stops in low power states
when sys_clock is cut. That makes gptimer based clocksource option
useless for OMAP2/3/4 devices with sys_clock as a clock input.
So, in order to use option 2, deeper idle state MUST be disabled.
Option 3 will still work but it is no better than 32K sync-timer
based clocksource.
We must support both sync timer and gptimer based clocksource as
some OMAP based derivative SoCs like AM33XX does not have the
sync timer.
Considering above, make sync-timer and gptimer clocksource runtime
selectable so that both OMAP and AMXXXX continue to use the same code.
And, in order to precisely configure/setup sched_clock for given
clocksource, decision has to be made early enough in boot sequence.
So, the solution is,
Use standard kernel parameter ("clocksource=") to override
default 32k_sync-timer, in addition to this, we also use hwmod database
lookup mechanism, through which at run-time we can identify availability
of 32k-sync timer on the device, else fall back to gptimer.
Also, moved low-level SoC specific init code to respective files,
(mach-omap1/timer32k.c and mach-omap2/timer.c)
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Cc: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
fix for a longstanding watchdog timer integration problem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJPqbWnAAoJEMePsQ0LvSpL+3AQAKUZP/qLl1l9duwBL8Cm9MLf
bzgCmdlHJeYlfqNJddK7qx8h/D00944Y8hbm4p/GIXTjAi6uZpW0Y0hWSTuDQNgJ
3WEP/tTTAGZDISqjTPKhp0mSQ3KCztoWKwhDmFrkQMSocDk7nGBRX1tx5ayAfmV4
OXVCAlNdo2hYzH+HSKBQZ0/z7PMv3kH+5gYEso3H36asb93V1R3KaEkrcpxhVgGZ
ViXUufWjGngR2bdNQfn621Pk38CvR+q+K0kG1QUAXnWTHxaXLgPLEJKutPVDbmme
IcViyTc59/je7kotFKbG+Hpt61ovcXk8s0UjYmEby9n8rBTxfEAbnXwMe6vSgQKN
hDN8VdMBOfxq7BjH69ylMUrUGy5juz0EWQ/tEZ3ARGKWX3KXtm2sP8lZ4hLJiGK+
MmaAjmGBkUsJ9Cj6fOFzzfbCnbxFSj64rq9YECdSYbmPJOLLPvpN1j61JToes2AZ
qdiukhgG4JFc+l/7DUObyhaY+411TLsmMEpvDS300vgq7h1CGOSBtMq+UfRUxx/J
qw/DZFEm5PWRcJTaQOVeA40iWgfhDCSd+q53Gq66SZLsdHZjs3vcdwwHZJ8OzQfK
WzWiqICNosS8Alm23suwSsIyw2xmtG3ZU6LyeUGT3AggIaqB5eOMbZTSMbhJHNV2
4cWmM2mRdb2KUaBpwuH/
=gBFx
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-c-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into devel-hwmod-data
Some OMAP IP block data additions for 3.5, along with a
fix for a longstanding watchdog timer integration problem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=qEmC
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-hwmod-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
Clean up of hwmod to shrink down the IP block interconnections
By Paul Walmsley
via Paul Walmsley (1) and Tony Lindgren (1)
* tag 'omap-cleanup-hwmod-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (29 commits)
ARM: OMAP2xxx: hwmod data: start to fix the IVA1, IVA2 and DSP
ARM: OMAP3: hwmod data: add IVA hard reset lines, main clock, clockdomain
ARM: OMAP3: hwmod data: fix IVA interface clock
ARM: OMAP2xxx: hwmod data: share common interface data
ARM: OMAP2xxx: hwmod data: share common hwmods between OMAP2420 and OMAP2430
ARM: OMAP2+: hwmod data: remove forward declarations, reorganize
ARM: OMAP: hwmod: remove code support for direct hwmod registration
ARM: OMAP2+: hwmod data: convert to link registration
ARM: OMAP2+: hwmod: add support for link registration
ARM: OMAP2+: hwmod: consolidate finding the MPU port index and storing it
ARM: OMAP2+: hwmod: add function to iterate over struct omap_hwmod_ocp_if
ARM: OMAP2+: hwmod: add _find_mpu_rt_port()
ARM: OMAP2+: hwmod: extend OCP_* register offsets from 16 to 32 bits
ARM: OMAP4: hwmod data: uncomment some "excluded" hwmods
ARM: OMAP4: hwmod data: add OCP_USER_DSP; mark omap44xx_dsp__iva appropriately
ARM: OMAP4: hwmod data: remove bandgap hwmod
ARM: OMAP3: hwmod data: GPTIMER12 is attached to a separate interconnect
ARM: OMAP3: hwmod data: add DSS->L3 interconnect for 3430ES1
ARM: OMAP3: hwmod data: fix interfaces for the MMC hwmods
ARM: OMAP2/3: hwmod data: update old names
...
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=MQ+t
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-sparse-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
Sparse and cppcheck warning fixes
By Paul Walmsley
via Paul Walmsley (1) and Tony Lindgren (1)
* tag 'omap-cleanup-sparse-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: clean up some cppcheck warnings
ARM: OMAP1: board files: deduplicate and clean some NAND-related code
ARM: OMAP: USB: remove unnecessary sideways include
ARM: OMAP: DMA: use constant array maximum, drop some LCD DMA code
ARM: OMAP: OCM RAM: use memset_io() when clearing SRAM
ARM: OMAP: fix 'using plain integer as NULL pointer' sparse warnings
ARM: OMAP2+: GPMC: resolve type-conversion warning from sparse
ARM: OMAP1: OHCI: use platform_data fn ptr to enable OCPI bus
ARM: OMAP1: OCPI: move to mach-omap1/
ARM: OMAP: add includes for missing prototypes
ARM: OMAP2+: declare file-local functions as static
Signed-off-by: Olof Johansson <olof@lixom.net>
Implement a custom reset function for the HDQ1W IP block. This is
because the HDQ1W IP block, like I2C, has an internal clock gating bit
that needs to be toggled after setting the SOFTRESET bit to allow the
reset to propagate.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Avinash.H.M <avinashhm@ti.com>
Tested-by: NeilBrown <neilb@suse.de>
Add MMC for 2420 so we can pass the DMA request lines the same
way as we already do on omap2430 and later.
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
[paul@pwsan.com: updated to apply on top of the 3.5 hwmod cleanup;
changed mmc hwmod name/class to "msdi" as documented in the 2420 TRM Rev X;
added sysconfig register information; added 16 bit register width flag;
added MSDI custom reset code]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
powerdomain, PRM, and CM changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Q4kv
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-b-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into devel-prcm
Some OMAP PRCM updates for 3.5. Includes some clock, clockdomain,
powerdomain, PRM, and CM changes.
The system dma module has capabiities register indicating
the support for descriptor loading, constant fill, etc.
Use this instead of OMAP revision check to identify the features
supported runtime.
This avoids patching the code for feature SOCs which has
those capabilities.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
We do not use iclk anywhere in the dmtimer driver and so removing it.
Hence removing the timer iclk entries from OMAP4 clkdev table as well.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
To improve the clarity of the code, replace the CK_3517 flag used in
the clock data with CK_AM35XX. The CK_3505 flag can also be
removed, since it is now unused.
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP44xx family of SoCs. There still seem to be a few missing, such
as those for the MMU IP blocks, but this seems to cover the bulk of
the remainder.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=ToTm
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-a-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into devel-hwmod
Add in most of the remaining hwmods (IP block descriptions) for the
OMAP44xx family of SoCs. There still seem to be a few missing, such
as those for the MMU IP blocks, but this seems to cover the bulk of
the remainder.
control code for OMAP SoCs. In particular, this series results in
a considerable diffstat savings by changing the way that IP block
interconnections are defined.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=NqUz
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-b-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into cleanup-hwmod
Clean up various aspects of the OMAP hwmod code, which is the IP block
control code for OMAP SoCs. In particular, this series results in
a considerable diffstat savings by changing the way that IP block
interconnections are defined.
Add the SL2 interface IP block and interconnect data. The SL2 is related
to the IVA-HD subsystem.
Add IP block and interconnect data for the C2C ("Chip-to-chip")
interconnect. This can provide a direct system interconnect link to
other devices stacked on the OMAP package.
Add the ELM IP block and interconnect data. The ELM can be used
to locate errors in NAND flash connected to the GPMC.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Now that the data has been converted to use interface registration, we
can remove the (now unused) direct hwmod registration code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Add support for direct IP block interconnect ("link") registration to
the hwmod code via a new function, omap_hwmod_register_links(). This
will replace direct registration of hwmods, and a subsequent patch
will remove omap_hwmod_register().
This change will allow a subsequent patch to remove the hwmod data
link arrays. This will reduce the size of the hwmod static data and
also make it easier to generate the data files. It will also make it
possible to share some of the struct omap_hwmod records across
multiple SoCs, since the link array pointers will be removed from the
struct omap_hwmod.
The downside is that boot time will increase. Minimizing boot time
was the reason why the link arrays were originally introduced.
Removing them will require extra computation during boot to allocate
memory and associate IP blocks with their interconnects. However,
since the current kernel development focus is on reducing the number
of lines in arch/arm/mach-omap2/, boot time impact is now seemingly
considered a lower priority.
This patch contains additional complexity to reduce the number of
memory allocations required for this change. This reduces the boot
time impact: total hwmod link registration time was ~ 2655
microseconds with a simple allocation strategy, but is now ~ 549
microseconds[1] with the approach taken by this patch.
1. Measured on a BeagleBoard 35xx @ 500MHz MPU/333 MHz CORE, average
of 7 samples. Total uncertainty is +/- 61 microseconds.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Extend the OCP_* register offsets in the struct
omap_hwmod_class_sysconfig to 32 bits. This is required to add the
OMAP4+ GPU hwmod, which uses OCP_* register offsets larger than 16
bits.
Another possible solution may be to simply add a single 16 bit offset
field in this structure, and to add code to factor that offset into
all OCP_* register accesses. This would save some memory, since
almost no modules need 32 bit offsets.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
One of the OMAP4 links was missing OCP_USER flags, since it was only
used by the DSP initiator, and we did not have an OCP_USER_DSP flag.
Future patches will switch the hwmod code and data to register
interfaces, rather than hwmods, and it will be mandatory for all
interfaces to have at least one user bit set. This patch resolves the
issue by adding OCP_USER_DSP and marking the DSP-IVA interface
appropriately.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
The timer integration code pokes around in hwmod data structures.
Those data structures are about to change. Define a function,
omap_hwmod_get_resource_byname(), for the timer integration code to
use instead.
The original patch has been changed to use struct resource by Tony's
request, although the caller of this function should not be a driver._
Platform drivers should get their data through the regular platform_*
functions; DT drivers through the appropriate of_* functions. This a
function is only for use by OMAP core code in arch/arm/*omap*.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Revert one softreset regression and few other minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WQ2B
-----END PGP SIGNATURE-----
Merge tag 'omap-fixes-for-v3.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fix regression for bad uart muxing and oops when PM is not set.
Revert one softreset regression and few other minor fixes.
* tag 'omap-fixes-for-v3.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP1: DMTIMER: fix broken timer clock source selection
ARM: OMAP: serial: Fix the ocp smart idlemode handling bug
ARM: OMAP2+: UART: Fix incorrect population of default uart pads
ARM: OMAP: sram: fix BUG in dpll code for !PM case
ARM: OMAP2/3: VENC hwmods: Remove OCPIF_SWSUP_IDLE flag from VENC slave interface
ARM: OMAP2+: hwmod: Revert "ARM: OMAP2+: hwmod: Make omap_hwmod_softreset wait for reset status"
ARM: OMAP2+: hwmod: add softreset delay field and OMAP4 data
ARM: OMAP1: mux: add missing include
Currently the errata is populated based on cpu checks this can
be removed and replaced with module version check of uart ip block.
MVR reg is provided within the uart reg map use the same
to populate the errata and thus now errata population and handling
can be managed within the driver itself.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
arch/arm/mach-omap1, arch/arm/mach-omap2, and arch/arm/plat-omap.
Fixes all but one sparse warning and most of the useful
cppcheck warnings (excepting the warnings generated by the
dmtimer integration code which is going up via 3.4-rc fixes)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=QdMB
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-a2-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into cleanup-sparse
Resolve static analysis warnings generated by files in
arch/arm/mach-omap1, arch/arm/mach-omap2, and arch/arm/plat-omap.
Fixes all but one sparse warning and most of the useful
cppcheck warnings (excepting the warnings generated by the
dmtimer integration code which is going up via 3.4-rc fixes)
Now that we have OPP layer, and OMAP CPUfreq driver is using it, we no
longer need/use the clock framework code for filling up CPUfreq
tables. Remove it.
Removing this code also eliminates build errors when CPU_FREQ_TABLE
support is not enabled.
Thanks to Russell King for pointing out the parts I missed under
plat-omap in the original version and also pointing out the build
errors when CPUFREQ_TABLE support was not enabled.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
sparse warns when 0 is passed to a function expecting a pointer argument.
Resolve these warnings by replacing the 0 with NULL.
arch/arm/plat-omap/include/plat/dmtimer.h:319:34: warning: Using plain integer as NULL pointer
arch/arm/plat-omap/include/plat/dmtimer.h:324:35: warning: Using plain integer as NULL pointer
arch/arm/mach-omap2/irq.c:294:22: warning: Using plain integer as NULL pointer
arch/arm/mach-omap1/board-palmz71.c:292:50: warning: Using plain integer as NULL pointer
arch/arm/mach-omap1/board-palmz71.c:295:73: warning: Using plain integer as NULL pointer
arch/arm/mach-omap1/ams-delta-fiq.c:105:63: warning: Using plain integer as NULL pointer
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The OMAP1 OHCI driver needs to enable the OCPI IP block before it can
work. Previously, the driver was simply calling a symbol defined in
the OMAP platform code, but this is incorrect: drivers should be fully
decoupled from platform and architecture code.
So instead, modify the driver to call through a platform_data function
pointer instead. We skip any DT aspect, since OMAP1 is not scheduled
to be converted to DT in the near future.
This resolves the following sparse warning:
It also gets rid of a cpu_is_omap16xx() call in a driver.
In the long term, it probably makes sense to move the OCPI bus code to
somewhere under drivers/. This should avoid the whole platform_data/DT
issue with this function.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Several C files in arch/arm/mach-omap* and arch/arm/plat-omap declare
functions that are used by other files, but don't include the header
file where the prototype is declared. This results in the following
warnings from sparse:
arch/arm/mach-omap2/irq.c:114:5: warning: symbol 'omap_irq_pending' was not declared. Should it be static?
arch/arm/mach-omap2/irq.c:186:13: warning: symbol 'omap2_init_irq' was not declared. Should it be static?
arch/arm/mach-omap2/irq.c:191:13: warning: symbol 'omap3_init_irq' was not declared. Should it be static?
arch/arm/mach-omap2/irq.c:196:13: warning: symbol 'ti81xx_init_irq' was not declared. Should it be static?
arch/arm/mach-omap2/irq.c:233:39: warning: symbol 'omap2_intc_handle_irq' was not declared. Should it be static?
arch/arm/mach-omap2/irq.c:242:6: warning: symbol 'omap_intc_save_context' was not declared. Should it be static?
arch/arm/mach-omap2/irq.c:265:6: warning: symbol 'omap_intc_restore_context' was not declared. Should it be static?
arch/arm/mach-omap2/irq.c:291:6: warning: symbol 'omap3_intc_suspend' was not declared. Should it be static?
arch/arm/mach-omap2/irq.c:297:6: warning: symbol 'omap3_intc_prepare_idle' was not declared. Should it be static?
arch/arm/mach-omap2/irq.c:306:6: warning: symbol 'omap3_intc_resume_idle' was not declared. Should it be static?
arch/arm/mach-omap2/irq.c:312:39: warning: symbol 'omap3_intc_handle_irq' was not declared. Should it be static?
arch/arm/mach-omap2/omap-secure.c:59:12: warning: symbol 'omap_secure_ram_reserve_memblock' was not declared. Should it be static?
arch/arm/mach-omap2/board-zoom-display.c:133:13: warning: symbol 'zoom_display_init' was not declared. Should it be static?
arch/arm/plat-omap/common.c:73:13: warning: symbol 'omap_init_consistent_dma_size' was not declared. Should it be static?
arch/arm/mach-omap1/irq.c:61:5: warning: symbol 'omap_irq_flags' was not declared. Should it be static?
arch/arm/mach-omap1/irq.c:179:13: warning: symbol 'omap1_init_irq' was not declared. Should it be static?
arch/arm/mach-omap1/reset.c:11:6: warning: symbol 'omap1_restart' was not declared. Should it be static?
Fix by including the appropriate header files.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Senthilvadivu Guruswamy <svadivu@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Due to HW limitation, some IPs should not be accessed just after a
softreset. Since the current hwmod sequence is accessing the sysconfig
register just after the reset, it might lead to OCP bus error in
that case.
Add a new field in the sysconfig structure to specify a delay in usecs
needed after doing a softreset.
In the case of the ISS and FDIF modules, the L3 OCP port will be
disconnected upon a SW reset. That issue was confirmed with HW simulation
and an errata should be available soon. The HW recommendation to avoid
that is to wait for 100 OCP clk cycles, before accessing the IP.
Considering the worse case (OPP50), the L3 bus will run at 100 MHz,
so a 1 usec delay is needed. Add an x2 margin to be safe.
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Fernando Guzman Lugo <fernando.lugo@ti.com>
[paul@pwsan.com: dropped FDIF change for now since the hwmod data is not
yet upstream; the FDIF change will need to be added later once the FDIF
data is merged]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In the SYSC_TYPE1_XXX_MASK configuration, SYSC_XXX_SHIFT macro
is used which is not defined anywhere in the kernel.
Until now the build was going through successfully, since it
is not being used anywhere in kernel.
This bug got introduced by the commit
358f0e630d ("OMAP3: hwmod: support
to specify the offset position of various SYSCONFIG register bits.")
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This is a first pass of some of the merge window fallout for ARM platforms.
Nothing controversial:
* A system.h fallout fix for OMAP
* PXA fixes for breakage caused by the regulator struct changes
* GPIO fixes for OMAP to properly deal with dynamic IRQ allocation
* A mismerge in our arm-soc tree of an lpc32xx change for networking
* A fix for USB setup on tegra
* An undo of __init annotation of display mux setup on OMAP that's needed
at runtime
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=36Eb
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc fixes from Olof Johansson:
"This is a first pass of some of the merge window fallout for ARM
platforms.
Nothing controversial:
- A system.h fallout fix for OMAP
- PXA fixes for breakage caused by the regulator struct changes
- GPIO fixes for OMAP to properly deal with dynamic IRQ allocation
- A mismerge in our arm-soc tree of an lpc32xx change for networking
- A fix for USB setup on tegra
- An undo of __init annotation of display mux setup on OMAP that's
needed at runtime"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: pxa: fix build issue on stargate2
ARM: pxa: fix build issue on cm-x300
ARM: pxa: fix build failure for regulator consumer in em-x270.c
ARM: LPC32xx: clock.c: Fix lpc-eth clock reference
ARM: OMAP: pm: fix compilation break
ARM: OMAP: Remove OMAP_GPIO_IRQ macro definition
drivers: input: Fix OMAP_GPIO_IRQ with gpio_to_irq() in ams_delta_serio_exit()
ARM: OMAP: boards: Fix OMAP_GPIO_IRQ usage with gpio_to_irq()
ARM: pxa: fix regulator related build fail in magician_defconfig
ARM: tegra: Fix device tree AUXDATA for USB/EHCI
ARM: OMAP2+: Remove __init from DSI mux functions
Rob Herring has done a sweeping change cleaning up all of the mach/io.h includes,
moving some of the oft-repeated macros to a common location and removing a bunch of
boiler plate. This is another step closer to a common zImage for multiple platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=YIsn
-----END PGP SIGNATURE-----
Merge tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: cleanups of io includes" from Olof Johansson:
"Rob Herring has done a sweeping change cleaning up all of the
mach/io.h includes, moving some of the oft-repeated macros to a common
location and removing a bunch of boiler plate. This is another step
closer to a common zImage for multiple platforms."
Fix up various fairly trivial conflicts (<mach/io.h> removal vs changes
around it, tegra localtimer.o is *still* gone, yadda-yadda).
* tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (29 commits)
ARM: tegra: Include assembler.h in sleep.S to fix build break
ARM: pxa: use common IOMEM definition
ARM: dma-mapping: convert ARCH_HAS_DMA_SET_COHERENT_MASK to kconfig symbol
ARM: __io abuse cleanup
ARM: create a common IOMEM definition
ARM: iop13xx: fix missing declaration of iop13xx_init_early
ARM: fix ioremap/iounmap for !CONFIG_MMU
ARM: kill off __mem_pci
ARM: remove bunch of now unused mach/io.h files
ARM: make mach/io.h include optional
ARM: clps711x: remove unneeded include of mach/io.h
ARM: dove: add explicit include of dove.h to addr-map.c
ARM: at91: add explicit include of hardware.h to uncompressor
ARM: ep93xx: clean-up mach/io.h
ARM: tegra: clean-up mach/io.h
ARM: orion5x: clean-up mach/io.h
ARM: davinci: remove unneeded mach/io.h include
[media] davinci: remove includes of mach/io.h
ARM: OMAP: Remove remaining includes for mach/io.h
ARM: msm: clean-up mach/io.h
...
From Tony Lindgren:
"This contains the updated gpio_to_irq patches from Tarun, and a trivial
build fix from Govindraj to #include <asm/system_misc.h> in pm.c.
The DSI mux patch is the same."
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: pm: fix compilation break
ARM: OMAP: Remove OMAP_GPIO_IRQ macro definition
drivers: input: Fix OMAP_GPIO_IRQ with gpio_to_irq() in ams_delta_serio_exit()
ARM: OMAP: boards: Fix OMAP_GPIO_IRQ usage with gpio_to_irq()
ARM: OMAP2+: Remove __init from DSI mux functions
Since all references to OMAP_GPIO_IRQ macro are replaced now
with gpio_to_irq(), this can be removed altogether.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Core:
* Support for MMC 4.5 Data Tag feature -- we tag REQ_META, so devices
that support Data Tag will provide increased throughput for metadata.
* Faster detection of card removal on I/O errors.
Drivers:
* dw_mmc now supports eMMC Power Off Notify, has PCI support, and
implements pre_req and post_req for asynchronous requests.
* omap_hsmmc now supports device tree.
* esdhc now has power management support.
* sdhci-tegra now supports Tegra30 devices.
* sdhci-spear now supports hibernation.
* tmio_mmc now supports using a GPIO for card detection.
* Intel PCH now supports 8-bit bus transfers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=T4T+
-----END PGP SIGNATURE-----
Merge tag 'mmc-merge-for-3.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
Core:
* Support for MMC 4.5 Data Tag feature -- we tag REQ_META, so devices
that support Data Tag will provide increased throughput for metadata.
* Faster detection of card removal on I/O errors.
Drivers:
* dw_mmc now supports eMMC Power Off Notify, has PCI support, and
implements pre_req and post_req for asynchronous requests.
* omap_hsmmc now supports device tree.
* esdhc now has power management support.
* sdhci-tegra now supports Tegra30 devices.
* sdhci-spear now supports hibernation.
* tmio_mmc now supports using a GPIO for card detection.
* Intel PCH now supports 8-bit bus transfers.
* tag 'mmc-merge-for-3.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (53 commits)
mmc: sh_mmcif: simplify bitmask macros
mmc: sh_mobile_sdhi: support modular mmc-core with non-standard hotplug
mmc: sh_mobile_sdhi: add a callback for board specific init code
mmc: tmio: cosmetic: prettify the tmio_mmc_set_ios() function
mmc: sh_mobile_sdhi: do not manage PM clocks manually
mmc: tmio_mmc: remove unused sdio_irq_enabled flag
mmc: tmio_mmc: power status flag doesn't have to be exposed in platform data
mmc: sh_mobile_sdhi: pass card hotplug GPIO number to TMIO MMC
mmc: tmio_mmc: support the generic MMC GPIO card hotplug helper
mmc: tmio: calculate the native hotplug condition only once
mmc: simplify mmc_cd_gpio_request() by removing two parameters
mmc: sdhci-pci: allow 8-bit bus width for Intel PCH
mmc: sdhci: check interrupt flags in ISR again
mmc: sdhci-pci: Add MSI support
mmc: core: warn when card doesn't support HPI
mmc: davinci: Poll status for small size transfers
mmc: davinci: Eliminate spurious interrupts
mmc: omap_hsmmc: Avoid a regulator voltage change with dt
mmc: omap_hsmmc: Convert hsmmc driver to use device tree
mmc: sdhci-pci: add SDHCI_QUIRK2_HOST_OFF_CARD_ON for Medfield SDIO
...
Primarily gpio device driver changes with some minor side effects
under arch/arm and arch/x86. Also includes a few core changes such as
explicitly supporting (electrical) open source and open drain outputs
and some help for parsing gpio devicetree properties.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPcWQxAAoJEEFnBt12D9kB4NEQAKzyQFFyX/1ZGZaKH12OtcSf
DSQg/2lx9MIOISYYjsq6cQQGeUnlvaFxYkKkS+P4U6aNqw6xRaEtFhef6mVTWeFL
PNi81hXIkyzza9/lZkoK4IBSk09JBeJu+5t9BwGQnM4Yg2POqqOf+vICWF0iN6mt
TtNXJb6vqHiveMsUIRP8AdZzVpSztVo5//wAri7om77Qm+3aJiptt65zz0ghKRT8
Tzb61miqUS7XS3NdUYq8pTsh8J1E8rrRch5jJWsY/AmVr0Dhajv5ouOiyp43EpHZ
mTNP90zglT3c+CTfRIb9oALfjPA5O+3ncSyBSB4qOX1nLcKyFvheg5uozyx7NSNJ
Pw4M8fCnKXN20sCbHQB0bTF0ETW5fuMAiKhGCU+4GpsIKelZKqRcWS7Dho8RquW+
YLuDXJWVut4HyyvrPFJxPs1IuOYCKJ2pGqDEzznEPgkVSxX4vedGE1MzKtj+aHFH
oZuZLOa+WQcyGLkW1BRsJxTht5i1paE5D9bXZfLkOgDMmFMBZ/oe6mLj26WCb3UL
lhxoAgFUKKe1+YBzkLISRf09L0rdhzEjs59ryK/ZVOuizH2+STKvH3jNSxuroAnN
ZCuomdofKNY/2pv3q3pAwm3G20l0qMwAqAVqYjF09m/jfDhcquHS5UoTvMG5WZqv
TGUh/kfetnPB07F0CLGQ
=BSW8
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull GPIO changes for v3.4 from Grant Likely:
"Primarily gpio device driver changes with some minor side effects
under arch/arm and arch/x86. Also includes a few core changes such as
explicitly supporting (electrical) open source and open drain outputs
and some help for parsing gpio devicetree properties."
Fix up context conflict due to Laxman Dewangan adding sleep control for
the tps65910 driver separately for gpio's and regulators.
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
gpio/ep93xx: Remove unused inline function and useless pr_err message
gpio/sodaville: Mark broken due to core irqdomain migration
gpio/omap: fix redundant decoding of gpio offset
gpio/omap: fix incorrect update to context.irqenable1
gpio/omap: fix incorrect context restore logic in omap_gpio_runtime_*
gpio/omap: fix missing dataout context save in _set_gpio_dataout_reg
gpio/omap: fix _set_gpio_irqenable implementation
gpio/omap: fix trigger type to unsigned
gpio/omap: fix wakeup_en register update in _set_gpio_wakeup()
gpio: tegra: tegra_gpio_config shouldn't be __init
gpio/davinci: fix enabling unbanked GPIO IRQs
gpio/davinci: fix oops on unbanked gpio irq request
gpio/omap: Fix section warning for omap_mpuio_alloc_gc()
ARM: tegra: export tegra_gpio_{en,dis}able
gpio/gpio-stmpe: Fix the value returned by _get_value routine
Documentation/gpio.txt: Explain expected pinctrl interaction
GPIO: LPC32xx: Add output reading to GPO P3
GPIO: LPC32xx: Fix missing bit selection mask
gpio/omap: fix wakeups on level-triggered GPIOs
gpio/omap: Fix IRQ handling for SPARSE_IRQ
...
These are all specific to some driver. They are typically the platform
side of a change in the drivers directory, such as adding a new driver
or extending the interface to the platform. In cases where there is no
maintainer for the driver, or the maintainer prefers to have the
platform changes in the same branch as the driver changes, the patches
to the drivers are included as well.
A much smaller set of driver updates that depend on other branches
getting merged first will be sent later.
The new export of tegra_chip_uid conflicts with other changes in fuse.c.
In rtc-sa1100.c, the global removal of IRQF_DISABLED conflicts with
the cleanup of the interrupt handling of that driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=pQ3X
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: driver specific updates" from Arnd Bergmann:
"These are all specific to some driver. They are typically the
platform side of a change in the drivers directory, such as adding a
new driver or extending the interface to the platform. In cases where
there is no maintainer for the driver, or the maintainer prefers to
have the platform changes in the same branch as the driver changes,
the patches to the drivers are included as well.
A much smaller set of driver updates that depend on other branches
getting merged first will be sent later.
The new export of tegra_chip_uid conflicts with other changes in
fuse.c. In rtc-sa1100.c, the global removal of IRQF_DISABLED
conflicts with the cleanup of the interrupt handling of that driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fixed up aforementioned trivial conflicts.
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (94 commits)
ARM: SAMSUNG: change the name from s3c-sdhci to exynos4-sdhci
mmc: sdhci-s3c: add platform data for the second capability
ARM: SAMSUNG: support the second capability for samsung-soc
ARM: EXYNOS: add support DMA for EXYNOS4X12 SoC
ARM: EXYNOS: Add apb_pclk clkdev entry for mdma1
ARM: EXYNOS: Enable MDMA driver
regulator: Remove bq24022 regulator driver
rtc: sa1100: add OF support
pxa: magician/hx4700: Convert to gpio-regulator from bq24022
ARM: OMAP3+: SmartReflex: fix error handling
ARM: OMAP3+: SmartReflex: fix the use of debugfs_create_* API
ARM: OMAP3+: SmartReflex: micro-optimization for sanity check
ARM: OMAP3+: SmartReflex: misc cleanups
ARM: OMAP3+: SmartReflex: move late_initcall() closer to its argument
ARM: OMAP3+: SmartReflex: add missing platform_set_drvdata()
ARM: OMAP3+: hwmod: add SmartReflex IRQs
ARM: OMAP3+: SmartReflex: clear ERRCONFIG_VPBOUNDINTST only on a need
ARM: OMAP3+: SmartReflex: Fix status masking in ERRCONFIG register
ARM: OMAP3+: SmartReflex: Add a shutdown hook
ARM: OMAP3+: SmartReflex Class3: disable errorgen before disable VP
...
Conflicts:
arch/arm/mach-tegra/Makefile
arch/arm/mach-tegra/fuse.c
drivers/rtc/rtc-sa1100.c
This new subsystem provides a common way to talk to secondary processors
on an SoC, e.g. a DSP, GPU or service processor, using virtio as the
transport. In the long run, it should replace a few dozen vendor
specific ways to do the same thing, which all never made it into the
upstream kernel. There is a broad agreement that rpmsg is the way to
go here and several vendors have started working on replacing their
own subsystems.
Two branches each add one virtio protocol number. Fortunately the
numbers were agreed upon in advance, so there are only context changes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=SC55
-----END PGP SIGNATURE-----
Merge tag 'rpmsg' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "remoteproc/rpmsg: new subsystem" from Arnd Bergmann:
"This new subsystem provides a common way to talk to secondary
processors on an SoC, e.g. a DSP, GPU or service processor, using
virtio as the transport. In the long run, it should replace a few
dozen vendor specific ways to do the same thing, which all never made
it into the upstream kernel. There is a broad agreement that rpmsg is
the way to go here and several vendors have started working on
replacing their own subsystems.
Two branches each add one virtio protocol number. Fortunately the
numbers were agreed upon in advance, so there are only context
changes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fixed up trivial protocol number conflict due to the mentioned additions
next to each other.
* tag 'rpmsg' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (32 commits)
remoteproc: cleanup resource table parsing paths
remoteproc: remove the hardcoded vring alignment
remoteproc/omap: remove the mbox_callback limitation
remoteproc: remove the single rpmsg vdev limitation
remoteproc: safer boot/shutdown order
remoteproc: remoteproc_rpmsg -> remoteproc_virtio
remoteproc: resource table overhaul
rpmsg: fix build warning when dma_addr_t is 64-bit
rpmsg: fix published buffer length in rpmsg_recv_done
rpmsg: validate incoming message length before propagating
rpmsg: fix name service endpoint leak
remoteproc/omap: two Kconfig fixes
remoteproc: make sure we're parsing a 32bit firmware
remoteproc: s/big switch/lookup table/
remoteproc: bail out if firmware has different endianess
remoteproc: don't use virtio's weak barriers
rpmsg: rename virtqueue_add_buf_gfp to virtqueue_add_buf
rpmsg: depend on EXPERIMENTAL
remoteproc: depend on EXPERIMENTAL
rpmsg: add Kconfig menu
...
Conflicts:
include/linux/virtio_ids.h
These changes are all specific to one board only. We're trying to keep
the number of board files low, but generally board level updates are
ok on platforms that are working on moving towards DT based probing,
which will eventually lead to removing them.
The board-ams-delta.c board file gets a conflict between the removal of
ams_delta_config and the addition of a lot of other data. The Kconfig
file has two changes in the same line, and in exynos, the power domain
cleanup conflicts with the addition of the image sensor device.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: Amended a fix for a mismerge to board-omap4panda.c]
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=HPiJ
-----END PGP SIGNATURE-----
Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: board specific updates" from Arnd Bergmann/Olof Johansson:
"These changes are all specific to one board only. We're trying to
keep the number of board files low, but generally board level updates
are ok on platforms that are working on moving towards DT based
probing, which will eventually lead to removing them.
The board-ams-delta.c board file gets a conflict between the removal
of ams_delta_config and the addition of a lot of other data. The
Kconfig file has two changes in the same line, and in exynos, the
power domain cleanup conflicts with the addition of the image sensor
device.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: Amended a fix for a mismerge to board-omap4panda.c]
Signed-off-by: Olof Johansson <olof@lixom.net>"
Fixed up some fairly trivial conflicts manually.
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (82 commits)
i.MX35-PDK: Add Camera support
ARM : mx35: 3ds-board: add framebuffer device
pxa/hx4700: Remove pcmcia platform_device structure
ARM: pxa/hx4700: Reduce sleep mode battery discharge by 35%
ARM: pxa/hx4700: Remove unwanted request for GPIO105
ARM: EXYNOS: support Exynos4210-bus Devfreq driver on Nuri board
ARM: EXYNOS: Register JPEG on nuri
ARM: EXYNOS: Register JPEG on universal_c210
ARM: S5PV210: Enable JPEG on SMDKV210
ARM: S5PV210: Add JPEG board definition
ARM: EXYNOS: Enable JPEG on Origen
ARM: EXYNOS: Enable JPEG on SMDKV310
ARM: EXYNOS: Add __init attribute to universal_camera_init()
ARM: EXYNOS: Add __init attribute to nuri_camera_init()
ARM: S5PV210: Enable FIMC on SMDKC110
ARM: S5PV210: Enable FIMC on SMDKV210
ARM: S5PV210: Enable MFC on SMDKC110
ARM: S5PV210: Enable MFC on SMDKV210
ARM: EXYNOS: Enable G2D on SMDKV310
ARM: tegra: update defconfig
...
These changes are all specific to an soc family or the code for
one soc. Lots of work for Tegra3 this time, but also a lot of other
platforms. There will be another (smaller) set of soc patches later in
the merge window for stuff that has dependencies on external trees or
that was sent just before the merge window opened.
The asoc tree added a few devices to the i.mx platform, which conflict
with other devices added in the same place here.
The tegra Makefile conflicts between a number of branches, mostly because
of changes regarding localtimer.c, which was removed in the end.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WdYR
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: SoC specific updates" from Arnd Bergmann:
"These changes are all specific to an soc family or the code for one
soc. Lots of work for Tegra3 this time, but also a lot of other
platforms. There will be another (smaller) set of soc patches later
in the merge window for stuff that has dependencies on external trees
or that was sent just before the merge window opened.
The asoc tree added a few devices to the i.mx platform, which conflict
with other devices added in the same place here.
The tegra Makefile conflicts between a number of branches, mostly
because of changes regarding localtimer.c, which was removed in the
end.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fix up some trivial conflicts, including the mentioned Tegra Makefile.
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (51 commits)
ARM: EXYNOS: fix cycle count for periodic mode of clock event timers
ARM: EXYNOS: add support JPEG
ARM: EXYNOS: Add DMC1, allow PPMU access for DMC
ARM: SAMSUNG: Correct MIPI-CSIS io memory resource definition
ARM: SAMSUNG: fix __init attribute on regarding s3c_set_platdata()
ARM: SAMSUNG: Add __init attribute to samsung_bl_set()
ARM: S5PV210: Add usb otg phy control
ARM: S3C64XX: Add usb otg phy control
ARM: EXYNOS: Enable l2 configuration through device tree
ARM: EXYNOS: remove useless code to save/restore L2
ARM: EXYNOS: save L2 settings during bootup
ARM: S5P: add L2 early resume code
ARM: EXYNOS: Add support AFTR mode on EXYNOS4210
ARM: mx35: Setup the AIPS registers
ARM: mx5: Use common function for configuring AIPS
ARM: mx3: Setup AIPS registers
ARM: mx3: Let mx31 and mx35 enter in LPM mode in WFI
ARM: defconfig: imx_v6_v7: build in REGULATOR_FIXED_VOLTAGE
ARM: imx: update imx_v6_v7_defconfig
ARM: tegra: Demote EMC clock inconsistency BUG to WARN
...
Quite a bit of code gets removed, and some stuff moved around, mostly
the old samsung s3c24xx stuff. There should be no functional changes
in this series otherwise. Some cleanups have dependencies on other
arm-soc branches and will be sent in the second round.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=o5Xl
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: global cleanups" from Arnd Bergmann:
"Quite a bit of code gets removed, and some stuff moved around, mostly
the old samsung s3c24xx stuff. There should be no functional changes
in this series otherwise. Some cleanups have dependencies on other
arm-soc branches and will be sent in the second round.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fixed up trivial conflicts mainly due to #include's being changes on
both sides.
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (121 commits)
ep93xx: Remove unnecessary includes of ep93xx-regs.h
ep93xx: Move EP93XX_SYSCON defines to SoC private header
ep93xx: Move crunch code to mach-ep93xx directory
ep93xx: Make syscon access functions private to SoC
ep93xx: Configure GPIO ports in core code
ep93xx: Move peripheral defines to local SoC header
ep93xx: Convert the watchdog driver into a platform device.
ep93xx: Use ioremap for backlight driver
ep93xx: Move GPIO defines to gpio-ep93xx.h
ep93xx: Don't use system controller defines in audio drivers
ep93xx: Move PHYS_BASE defines to local SoC header file
ARM: EXYNOS: Add clock register addresses for EXYNOS4X12 bus devfreq driver
ARM: EXYNOS: add clock registers for exynos4x12-cpufreq
PM / devfreq: update the name of EXYNOS clock registers that were omitted
PM / devfreq: update the name of EXYNOS clock register
ARM: EXYNOS: change the prefix S5P_ to EXYNOS4_ for clock
ARM: EXYNOS: use static declaration on regarding clock
ARM: EXYNOS: replace clock.c for other new EXYNOS SoCs
ARM: OMAP2+: Fix build error after merge
ARM: S3C24XX: remove call to s3c24xx_setup_clocks
...
Simple bug fixes that were not considered important enough for inclusion
into 3.3. One bug fix was originally intended for 3.3 but accidentally
got missed, but is not marked stable because it should only get
backported once later fixes also make it into v3.4.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=eLYz
-----END PGP SIGNATURE-----
Merge tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: Non-critical bug fixes" from Ardn Bergmann:
"Simple bug fixes that were not considered important enough for
inclusion into 3.3. One bug fix was originally intended for 3.3 but
accidentally got missed, but is not marked stable because it should
only get backported once later fixes also make it into v3.4.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
* tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (66 commits)
iomux-mx25.h slew rate adjusted for LCD __LD pins
ARM: davinci: DA850: move da850_register_pm to .init.text
ARM: davinci: cpufreq: fix compiler warning
ARM: OMAP2+: Fix build for omap4 only builds with missing include of linux/bug.h
ARM: OMAP2+: Fix section warnings for hsmmc_init_one
ARM: OMAP2+: Fix build issues with missing include of linux/bug.h
ARM: OMAP2+: gpmc-smsc911x: only register regulator for first instance
ARM: OMAP3+: PM: VP: fix integer truncation error
ARM: OMAP2+: PM: fix wakeupgen warning when hotplug disabled
ARM: OMAP2+: PM: fix section mismatch with omap2_init_processor_devices()
ARM: OMAP2: Fix section warning for n8x0 when CONFIG_MMC_OMAP is not set
ARM: OMAP2+: Fix omap24xx_io_desc warning if SoC subtypes are not selected
ARM: OMAP1: Fix section mismatch for omap1_init_early()
ARM: OMAP1: Fix typo in lcd_dma.c
ARM: OMAP: mailbox: trivial whitespace fix
ARM: OMAP: Remove definition cpu_is_omap4430()
ARM: OMAP2+: included some headers twice
ARM: OMAP: clock.c: included linux/debugfs.h twice
ARM: OMAP: don't build hwspinlock in vain
ARM: OMAP2+: ads7846_init: put gpio_pendown into pdata if it's provided
...
set_sleep seems to be unused in omap_hsmmc driver. so get rid of it.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Pull #1 ARM updates from Russell King:
"This one covers stuff which Arnd is waiting for me to push, as this is
shared between both our trees and probably other trees elsewhere.
Essentially, this contains:
- AMBA primecell device initializer updates - mostly shrinking the
size of the device declarations in platform code to something more
reasonable.
- Getting rid of the NO_IRQ crap from AMBA primecell stuff.
- Nicolas' idle cleanups. This in combination with the restart
cleanups from the last merge window results in a great many
mach/system.h files being deleted."
Yay: ~80 files, ~2000 lines deleted.
* 'for-armsoc' of git://git.linaro.org/people/rmk/linux-arm: (60 commits)
ARM: remove disable_fiq and arch_ret_to_user macros
ARM: make entry-macro.S depend on !MULTI_IRQ_HANDLER
ARM: rpc: make default fiq handler run-time installed
ARM: make arch_ret_to_user macro optional
ARM: amba: samsung: use common amba device initializers
ARM: amba: spear: use common amba device initializers
ARM: amba: nomadik: use common amba device initializers
ARM: amba: u300: use common amba device initializers
ARM: amba: lpc32xx: use common amba device initializers
ARM: amba: netx: use common amba device initializers
ARM: amba: bcmring: use common amba device initializers
ARM: amba: ep93xx: use common amba device initializers
ARM: amba: omap2: use common amba device initializers
ARM: amba: integrator: use common amba device initializers
ARM: amba: realview: get rid of private platform amba_device initializer
ARM: amba: versatile: get rid of private platform amba_device initializer
ARM: amba: vexpress: get rid of private platform amba_device initializer
ARM: amba: provide common initializers for static amba devices
ARM: amba: make use of -1 IRQs warn
ARM: amba: u300: get rid of NO_IRQ initializers
...
It includes:
- drivers for Samsung Exynos MIPI DSI and display port
- i740fb to support those old Intel chips
- large updates to OMAP, viafb and sh_mobile_lcdcfb
- some updates to s3c-fb and udlfb, few patches to others
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)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=uO8m
-----END PGP SIGNATURE-----
Merge tag 'fbdev-updates-for-3.4' of git://github.com/schandinat/linux-2.6
Pull fbdev updates for 3.4 from Florian Tobias Schandinat:
- drivers for Samsung Exynos MIPI DSI and display port
- i740fb to support those old Intel chips
- large updates to OMAP, viafb and sh_mobile_lcdcfb
- some updates to s3c-fb and udlfb, few patches to others
Fix up conflicts in drivers/video/udlfb.c due to Key Sievers' fix making
it in twice.
* tag 'fbdev-updates-for-3.4' of git://github.com/schandinat/linux-2.6: (156 commits)
Revert "video:uvesafb: Fix oops that uvesafb try to execute NX-protected page"
OMAPDSS: register dss drivers in module init
video: pxafb: add clk_prepare/clk_unprepare calls
fbdev: bfin_adv7393fb: Drop needless include
fbdev: sh_mipi_dsi: add extra phyctrl for sh_mipi_dsi_info
fbdev: remove dependency of FB_SH_MOBILE_MERAM from FB_SH_MOBILE_LCDC
Revert "MAINTAINERS: add entry for exynos mipi display drivers"
fbdev: da8xx: add support for SP10Q010 display
fbdev: da8xx:: fix reporting of the display timing info
drivers/video/pvr2fb.c: ensure arguments to request_irq and free_irq are compatible
OMAPDSS: APPLY: fix clearing shadow dirty flag with manual update
fbdev: sh_mobile_meram: Implement system suspend/resume
fbdev: sh_mobile_meram: Remove unneeded sanity checks
fbdev: sh_mobile_meram: Don't perform update in register operation
arm: mach-shmobile: Constify sh_mobile_meram_cfg structures
fbdev: sh_mobile_lcdc: Don't store copy of platform data
fbdev: sh_mobile_meram: Remove unused sh_mobile_meram_icb_cfg fields
arm: mach-shmobile: Don't set MERAM ICB numbers in platform data
fbdev: sh_mobile_meram: Allocate ICBs automatically
fbdev: sh_mobile_meram: Use genalloc to manage MERAM allocation
...
Pull input subsystem updates from Dmitry Torokhov:
"- we finally merged driver for USB version of Synaptics touchpads
(I guess most commonly found in IBM/Lenovo keyboard/touchpad combo);
- a bunch of new drivers for embedded platforms (Cypress
touchscreens, DA9052 OnKey, MAX8997-haptic, Ilitek ILI210x
touchscreens, TI touchscreen);
- input core allows clients to specify desired clock source for
timestamps on input events (EVIOCSCLOCKID ioctl);
- input core allows querying state of all MT slots for given event
code via EVIOCGMTSLOTS ioctl;
- various driver fixes and improvements."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (45 commits)
Input: ili210x - add support for Ilitek ILI210x based touchscreens
Input: altera_ps2 - use of_match_ptr()
Input: synaptics_usb - switch to module_usb_driver()
Input: convert I2C drivers to use module_i2c_driver()
Input: convert SPI drivers to use module_spi_driver()
Input: omap4-keypad - move platform_data to <linux/platform_data>
Input: kxtj9 - who_am_i check value and initial data rate fixes
Input: add driver support for MAX8997-haptic
Input: tegra-kbc - revise device tree support
Input: of_keymap - add device tree bindings for simple key matrices
Input: wacom - fix physical size calculation for 3rd-gen Bamboo
Input: twl4030-vibra - really switch from #if to #ifdef
Input: hp680_ts_input - ensure arguments to request_irq and free_irq are compatible
Input: max8925_onkey - avoid accessing input device too early
Input: max8925_onkey - allow to be used as a wakeup source
Input: atmel-wm97xx - convert to dev_pm_ops
Input: atmel-wm97xx - set driver owner
Input: add cyttsp touchscreen maintainer entry
Input: cyttsp - remove useless checks in cyttsp_probe()
Input: usbtouchscreen - add support for Data Modul EasyTouch TP 72037
...
Here is the first big update chunk of sound stuff for 3.4-rc1.
In the common sound infrastructure, there are a few changes for
dynamic PCM support (used in ASoC) and a few clean-ups. Majority of
changes are found, as usual, in HD-audio and ASoC.
Some highlights of HD-audio changes:
- All the long-standing static quirk codes for Realtek codec were
finally removed by fixing and extending the Realtek auto-parser.
- The mute-LED control is standardized over all HD-audio codec
drivers using the extended vmaster hook.
- The vmaster slave mixer elements are initialized to 0dB as default
so that the user won't be annoyed by the silent output after
updates, e.g. due to the additions of new elements.
- Other many fix-ups for the misc HD-audio devices.
In the ASoC side, this is a very active release, including a quite a
few framework enhancements. Some highlights:
- Support for widgets not associated with a CODEC, an important part
of the dynamic PCM framework.
- A library factoring out the common code shared by dmaengine based
DMA drivers contributed by Lars-Peter Clausen. This will save a lot
of code and make it much easier to deploy enhancements to
dmaengine.
- Support for binary controls, used for providing runtime
configuration of algorithm coefficients.
- A new DAPM widget type for regulator supplies allowing drivers for
devices that can power down unused supplies while active to do
without any per-driver code.
- DAPM widgets for DAIs, initially giving a speed boost for playback
startup and shutdown and also the basis for CODEC<->CODEC DAI link
support.
- Support for specifying the number of significant bits on audio
interfaces, useful for allowing applications to know how much effort
to put into generating data for a larger sample format.
- Conversion of the FSI driver used on some SH processors to
DMAEngine.
- Conversion of EP93xx drivers to DMAEngine.
- New CODEC drivers for Maxim MAX9768 and Wolfson Microelectronics
WM2200.
- Move audmux driver from arc/arm to sound/soc
- McBSP move from arch/ to sound/ and updates
Also, a few small updates and fixes for other drivers like au88x0,
ymfpci, USB 6fire, USB usx2yaudio are included.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQIcBAABAgAGBQJPawmuAAoJEGwxgFQ9KSmkdR0QALDDI/eUo4il40C33Gt/OSDz
Wkz+FOwp2ddbIqHc0n41sV7+FV1MuyzQ37uSw8zhK724Vd4tCqX6O5K1uvS1iSbh
jxHsy5XtfvCs2cjb61H6N+rfWcqC69gGhpc1mLoelj/PYl7S2iV5xOgTr4trVk2Y
UN7Y13b4hzZvubRUozoTldaIgdhrj8D8KO7qQNYehyG19b4bJ00Rk4K5JdjsFwbE
dTGl/ZUv50Fnx6PAWwqzh1a3cPabHA1TZDiKQM2nuE91e/Ecs4c7t1CRvW8m8mlr
u4D4N8PJcCN4SPDd2YuVBgan4SQ0kxKTaup11bHSvAWai2zPX5xMB1yoJNxgjSMt
5NHrGdR4+lQEVlBVXe2sWb4/3vE2kr2dtcGGR/FBFJTuLWDFFtRcnxeQJI8qRNUw
UdwDuGXdActoc1cZz2dsKvXMOs0TKT6OCdQH+dHBglW/W8wMkVocZclUgbQM66/X
gwvk0jfZ9p3UcKnYt3RkxiXQvAJsr8v0HhYcKvQCFhJArZufdeRHB7LCVRTm692Y
/BKZgK4QHxtGw3Yc7emYidKeRSP1ml5QlvC4zMIoGqiahqa8LI8Qcb5knvIEmU8q
kY5k0fVP+paf0dceAVXyFZsRB9AyX2eUdufDPifXtydQZgj4o9A7Sy/teWl77EgF
Mafq4QUzo1U4i8JpAM4d
=5FJq
-----END PGP SIGNATURE-----
Merge tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull updates of sound stuff from Takashi Iwai:
"Here is the first big update chunk of sound stuff for 3.4-rc1.
In the common sound infrastructure, there are a few changes for
dynamic PCM support (used in ASoC) and a few clean-ups. Majority of
changes are found, as usual, in HD-audio and ASoC.
Some highlights of HD-audio changes:
- All the long-standing static quirk codes for Realtek codec were
finally removed by fixing and extending the Realtek auto-parser.
- The mute-LED control is standardized over all HD-audio codec
drivers using the extended vmaster hook.
- The vmaster slave mixer elements are initialized to 0dB as default
so that the user won't be annoyed by the silent output after
updates, e.g. due to the additions of new elements.
- Other many fix-ups for the misc HD-audio devices.
In the ASoC side, this is a very active release, including a quite a
few framework enhancements. Some highlights:
- Support for widgets not associated with a CODEC, an important part
of the dynamic PCM framework.
- A library factoring out the common code shared by dmaengine based
DMA drivers contributed by Lars-Peter Clausen. This will save a
lot of code and make it much easier to deploy enhancements to
dmaengine.
- Support for binary controls, used for providing runtime
configuration of algorithm coefficients.
- A new DAPM widget type for regulator supplies allowing drivers for
devices that can power down unused supplies while active to do
without any per-driver code.
- DAPM widgets for DAIs, initially giving a speed boost for playback
startup and shutdown and also the basis for CODEC<->CODEC DAI link
support.
- Support for specifying the number of significant bits on audio
interfaces, useful for allowing applications to know how much
effort to put into generating data for a larger sample format.
- Conversion of the FSI driver used on some SH processors to
DMAEngine.
- Conversion of EP93xx drivers to DMAEngine.
- New CODEC drivers for Maxim MAX9768 and Wolfson Microelectronics
WM2200.
- Move audmux driver from arc/arm to sound/soc
- McBSP move from arch/ to sound/ and updates
Also, a few small updates and fixes for other drivers like au88x0,
ymfpci, USB 6fire, USB usx2yaudio are included."
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (446 commits)
ASoC: wm8994: Provide VMID mode control and fix default sequence
ASoC: wm8994: Add missing break in resume
ASoC: wm_hubs: Don't actively manage LINEOUT_VMID_BUF
ASoC: pxa-ssp: atomically set stream active masks
ASoC: fsl: p1022ds: tell the WM8776 codec driver that it's the master
ASoC: Samsung: Added to support mono recording
ALSA: hda - Fix build with CONFIG_PM=n
ALSA: au88x0 - Avoid possible Oops at unbinding
ALSA: usb-audio - Fix build error by consitification of rate list
ASoC: core: Fix obscure leak of runtime array
ALSA: pcm - Avoid GFP_ATOMIC in snd_pcm_link()
ALSA: pcm: Constify the list in snd_pcm_hw_constraint_list
ASoC: wm8996: Add 44.1kHz support
ALSA: hda - Fix build of patch_sigmatel.c without CONFIG_SND_HDA_POWER_SAVE
ASoC: mx27vis-aic32x4: Convert it to platform driver
ALSA: hda - fix printing of high HDMI sample rates
ALSA: ymfpci - Fix legacy registers on S3/S4 resume
ALSA: control - Fixe a trailing white space error
ALSA: hda - Add expose_enum_ctl flag to snd_hda_add_vmaster_hook()
ALSA: hda - Add "Mute-LED Mode" enum control
...
Conflicts:
arch/arm/mach-lpc32xx/clock.c
arch/arm/mach-pxa/pxa25x.c
arch/arm/mach-pxa/pxa27x.c
The conflicts with pxa are non-obvious, we have multiple branches
adding and removing the same clock settings. According to
Haojian Zhuang, removing the sa1100 rtc dummy clock is the correct
fix here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch allows us to drop the OMAP dependency from the OMAP4 keypad
driver.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'ep93xx-for-arm-soc' of git://github.com/RyanMallon/linux-2.6:
ep93xx: Remove unnecessary includes of ep93xx-regs.h
ep93xx: Move EP93XX_SYSCON defines to SoC private header
ep93xx: Move crunch code to mach-ep93xx directory
ep93xx: Make syscon access functions private to SoC
ep93xx: Configure GPIO ports in core code
ep93xx: Move peripheral defines to local SoC header
ep93xx: Convert the watchdog driver into a platform device.
ep93xx: Use ioremap for backlight driver
ep93xx: Move GPIO defines to gpio-ep93xx.h
ep93xx: Don't use system controller defines in audio drivers
ep93xx: Move PHYS_BASE defines to local SoC header file
(update to v3.3-rc7)
Conflicts:
arch/arm/mach-s3c2440/common.h
* tag 'imx25-iomux-ds' of git://git.pengutronix.de/git/imx/linux-2.6:
iomux-mx25.h slew rate adjusted for LCD __LD pins
(update to v3.3-rc6)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Several platforms create IOMEM defines for casting to 'void __iomem *',
and other platforms are incorrectly using __io() macro for the same
purpose. This creates a common definition and removes all the platform
specific versions. Rather than try to make linux/io.h and asm/io.h
assembly safe, the assembly version of IOMEM is moved into
asm/assembler.h.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ryan Mallon <rmallon@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Cc: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Cc: Colin Cross <ccross@android.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
* 'next/cleanup-exynos-clock' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Add clock register addresses for EXYNOS4X12 bus devfreq driver
ARM: EXYNOS: add clock registers for exynos4x12-cpufreq
PM / devfreq: update the name of EXYNOS clock registers that were omitted
PM / devfreq: update the name of EXYNOS clock register
ARM: EXYNOS: change the prefix S5P_ to EXYNOS4_ for clock
ARM: EXYNOS: use static declaration on regarding clock
ARM: EXYNOS: replace clock.c for other new EXYNOS SoCs
(includes an update to v3.3-rc6)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPW8yUAAoJEHm+PkMAQRiGhFIH/RGUPxGmUkJv8EP5I4HDA4dJ
c6/PrzZCHs8rxzYzvn7ojXqZGXTOAA5ZgS9A6LkJ2sxMFvgMnkpFi6B4CwMzizS3
vLWo/HNxbiTCNGFfQrhQB8O58uNI8wOBa87lrQfkXkDqN0cFhdjtIxeY1BD9LXIo
qbWysGxCcZhJWHapsQ3NZaVJQnIK5vA/+mhyYP4HzbcHI3aWnbIEZ8GQKeY28Ch0
+pct5UQBjZavV5SujaW0Xd65oIiycm8XHAQw6FxQy//DfaabauWgFteR162Q/oew
xxUBDOHF3nO1bdteHHaYqxig0j1MbIHsqxTnE/neR8UryF04//1SFF7DYuY/1pg=
=SV5V
-----END PGP SIGNATURE-----
Merge tag 'v3.3-rc7' into gpio/next
Linux 3.3-rc7. Merged into the gpio branch to pick up gpio bugfixes already
in mainline before queueing up move v3.4 patches
Clock signal muxing, and functional clock related defines are only needed
in ASoC drivers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Mark Brown <broonoie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
The driver for omap-mcbsp-dai no longer exist since it has been merged with
the omap-mcbsp driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
The OMAP McBSP driver stack used to contain two different
drivers. One of them was used as kind low-level access to
the IP, while the other driver was the ASoC DAI driver.
There were global, shared structures, in different places,
the McBSP instances are reffered with id numbers (sometimes
0 based, in other cases 1 based id numbers).
Create one single driver for OMAP McBSP with name: omap-mcbsp.
Convert the old omap-mcbsp driver initially to be a library
for the omap-mcbsp DAI driver. With this change we can get rid
of all global variables, structures.
Further cleanup is coming...
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Move most of the content of the plat/mcbsp.h header file under
sound/soc/omap/ to help further cleanups.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Convert the plat-omap/mcbsp.c driver to be proper platform driver.
Remove the omap_mcbsp_init function call which was called from
mach-omap1/2/mcbsp.c to register the platform driver for the just
created platform device in the same function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
* 'board' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: add minimal support for Nokia RM-696
ARM: OMAP: enable Bluetooth on the PandaBoard
ARM: OMAP: pandora: add support for backlight and poweroff
ARM: OMAP4: board-4430sdp: don't initialize value that is never used
ARM: OMAP3: cm-t3517: add EMAC support
ARM: OMAP: move generic EMAC init to separate file
ARM: OMAP3: RX-51: add explicit mux configuration of tsc2005 control gpios
ARM: OMAP: Add omap_reserve functionality
(includes sync-up to 3.3-rc6)
* 'sr' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3+: SmartReflex: fix error handling
ARM: OMAP3+: SmartReflex: fix the use of debugfs_create_* API
ARM: OMAP3+: SmartReflex: micro-optimization for sanity check
ARM: OMAP3+: SmartReflex: misc cleanups
ARM: OMAP3+: SmartReflex: move late_initcall() closer to its argument
ARM: OMAP3+: SmartReflex: add missing platform_set_drvdata()
ARM: OMAP3+: hwmod: add SmartReflex IRQs
ARM: OMAP3+: SmartReflex: clear ERRCONFIG_VPBOUNDINTST only on a need
ARM: OMAP3+: SmartReflex: Fix status masking in ERRCONFIG register
ARM: OMAP3+: SmartReflex: Add a shutdown hook
ARM: OMAP3+: SmartReflex Class3: disable errorgen before disable VP
ARM: OMAP3+: SmartReflex: fix err interrupt disable sequence
ARM: OMAP3+: SmartReflex: use voltage domain name in device attributes
ARM: OMAP2+: Fix devexit for smartreflex when CONFIG_HOTPLUG is not set
ARM: OMAP2+: Fix zoom LCD backlight if TWL_CORE is not selected
ARM: OMAP2+: Fix board_mux section type conflict when OMAP_MUX is not set
ARM: OMAP2+: Fix OMAP_HDQ_BASE build error
ARM: OMAP2+: Fix Kconfig dependencies for USB_ARCH_HAS_EHCI
ARM: OMAP2+: I2C: always compile I2C reset code, even if I2C driver is not built
* 'uart' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: remove some orphan function declarations.
ARM: OMAP2+: UART: remove unused fields in omap_uart_state.
* 'cleanup-pm' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: PM: share some suspend-related functions across OMAP2, 3, 4
ARM: OMAP2+: omap_device: call all suspend, resume callbacks when OMAP_DEVICE_NO_IDLE_ON_SUSPEND is set
ARM: OMAP: omap_device: remove omap_device_parent
ARM: OMAP2+: PM debug: fix the use of debugfs_create_* API
ARM: OMAP2+: PM: share clkdms_setup() across OMAP2, 3, 4
ARM: OMAP2+: PM: clean up omap_set_pwrdm_state()
ARM: OMAP3: PM: remove superfluous calls to pwrdm_clear_all_prev_pwrst()
ARM: OMAP: convert omap_device_build() and callers to __init
ARM: OMAP2+: Mark omap_hsmmc_init and omap_mux related functions as __init
ARM: OMAP2+: Split omap2_hsmmc_init() to properly support I2C GPIO pins
ARM: OMAP: omap_device: Expose omap_device_{alloc, delete, register}
ARM: OMAP: Fix build error when mmc_omap is built as module
ARM: OMAP: Fix kernel panic with HSMMC when twl4030_gpio is a module
* 'ams-delta' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ASoC: OMAP: ams-delta: drop .set_bias_level callback
ARM: OMAP1: ams-delta: update the modem to use regulator API
ARM: OMAP1: ams-delta: set up regulator over modem reset GPIO pin
ARM: OMAP1: ams-delta: clean up init data section assignments
ARM: OMAP1: ams-delta: fix incorrect section tags
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=a6Ra
-----END PGP SIGNATURE-----
Merge tag 'imx35-imx5-aips-setup' of git://git.pengutronix.de/git/imx/linux-2.6 into next/soc
i.MX35/5 AIPS setup
Includes sync up to 3.3-rc6
* tag 'imx35-imx5-aips-setup' of git://git.pengutronix.de/git/imx/linux-2.6:
ARM: mx35: Setup the AIPS registers
ARM: mx5: Use common function for configuring AIPS
These are no longer needed with the recent iomap.h
changes.
Reported-by: Rob Herring <robherring2@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The definition cpu_is_omap4430() always returns 0 even when CONFIG_ARCH_OMAP4
is enabled. This macro should be removed and the macro cpu_is_omap443x() should
be used where needed for OMAP4430 devices.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update SRAM start & size for am33xx SoC's.
Note: cpu_is_34xx() is true for am33xx also. Doing
cpu_is_am33xx() check after cpu_is_34xx() will not
achieve what we want due to the above reason.
Hence cpu_is_am33xx() is done before cpu_is_34xx()
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently all omap_devices are forced to have the dummy device
'omap_device_parent' as a parent. This was used to distinguish
omap_devices from "normal" platform_devices in the OMAP PM core code.
Now that we implement the PM core using PM domains, this is no longer
needed, and is removed.
This also frees up omap_devices to have a more complex parent/child
relationships that model actual device relationships.
The only in-tree user of omap_device_parent was the OMAP PM layer to
handle lost-context count for omap_devices. That is now converted to
use the presence of the omap_device_pm_domain instead.
Signed-off-by: Kevin Hilman <khilman@ti.com>
The driver is still relying on internal OMAP IRQ defines that
are not relevant anymore if OMAP is built with SPARSE_IRQ.
Replace the defines with the proper IRQ base number.
Clean some comment style issue.
Remove some hidden and ugly cpu_class_is_omap1() inside the
gpio header.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Tested-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
To set sr ntarget values for all volt_domain,
volt_table is retrieved by doing a look_up of 'vdd_name'
field from omap_hwmod but voltage domain pointer does not
belong to omap_hwmod and is not used anywhere else.
As a part of voltage layer and SR Layer clean up volt
pointer is removed from omap_hwmod and added in dev
attributes of SR. The value of the field must match
the voltage domain names for the binding to be effective.
Tested on OMAP3630 SDP, OMAP3530 Beagleboard and
OMAP4430 SDP Board.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Shweta Gulati <shweta.gulati@ti.com>
Acked by: Nishanth Menon <nm@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This functionality has already been implemented in the cx20442 codec
driver (commit f75a8ff67d, "ASoC: cx20442:
add bias control over a platform provided regulator"), no need to keep
it here duplicated.
Once done, remove the no longer used AMS_DELTA_LATCH2_MODEM_NRESET
symbol from the board header file and a call to the regulator_toggle()
helper function from the old API wrapper found in the board file. While
being at it, simplify the way the modem .pm callback handles the
regulator and drop that helper function and its related consumer setup
completely.
Depends on patches 1/3 and 2/3 for clean apply and keep things working.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Conflicts:
arch/arm/mach-omap1/gpio16xx.c
drivers/gpio/gpio-omap.c
Merge in the runtime-pm-cleanup branch from the gpio tree into
next/cleanup, this resolves a nonobvious merge conflict between
the two branches. Both branches move parts of the gpio-omap
driver into platform code, this takes the superset of both
changes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix L4_EMU_34XX_BASE error after iomap changes
ARM: OMAP2+: Limit omap_read/write usage to legacy USB drivers
ARM: OMAP: Remove plat/io.h by splitting it into mach/io.h and mach/hardware.h
ARM: OMAP2+: Move most of plat/io.h into local iomap.h
ARM: OMAP1: Move most of plat/io.h into local iomap.h
ARM: OMAP1: Move 16xx GPIO system clock to platform init code
ARM: OMAP: Move omap_init_consistent_dma_size() to local common.h
ARM: OMAP2+: Move SDRC related functions from io.h into local common.h
ARM: OMAP2+: Drop DISPC L3 firewall code
ARM: OMAP2xxx: PM: remove obsolete timer disable code in the suspend path
ARM: OMAP: McSPI: Remove unused flag from struct omap2_mcspi_device_config
(update to latest rmk/for-arm-soc branch)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* 'omap1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
input: serio: ams-delta: toggle keyboard power over GPIO
omapfb: lcd_ams_delta: drive control lines over GPIO
MTD: NAND: ams-delta: use GPIO instead of custom I/O
LED: drop leds-ams-delta driver
ARM: OMAP1: ams-delta: supersede custom led device by leds-gpio
ARM: OMAP1: ams-delta: convert latches to basic_mmio_gpio
ARM: OMAP1: ams-delta: register latch dependent devices later
* 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: split omap2/3/4_check_revision function
ARM: OMAP2+: Make cpu_rev static global variable
The following commit: 2f31b51659
Author: Tero Kristo <t-kristo@ti.com>
Date: Fri Dec 16 14:37:00 2011 -0700
ARM: OMAP4: PRM: use PRCM interrupt handler
introduced the PRCM interrupt handler and thus the need
for 64 more interrupts. Since SPARSE_IRQ is still not fully
functional on OMAP, the NR_IRQS needs to be updated to avoid
the failure that happen during irq_alloc_descs call inside
the PRCM driver:
[ 0.208221] PRCM: failed to allocate irq descs: -12
Later the mux framework is then unable to request an IRQ from
the PRCM interrupt handler.
[ 1.802795] mux: Failed to setup hwmod io irq -22
Fix that by adding 64 more interrupts for OMAP2PLUS config.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Drivers should no longer use omap_read/write functions
but instead use ioremap + read/write functions.
As some USB legacy code is still shared between omap1 and
omap2420, let's limit the omap_read/write to plat/usb.h.
Note that the long term fix is to update the drivers to
use ioremap and read/write functions. That can now be
done as a separate patch series that is limited to the
USB drivers.
Also make sure the legacy omap1-keypad.c driver builds
if selected for 2420 based systems.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is needed to minimize io.h so the SoC specific io.h
for ARMs can removed.
Note that minimal driver changes for DSS and RNG are needed to
include cpu.h for SoC detection macros.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There's no need to have these defines in plat/io.h.
Note that we now need to ifdef omap_read/write calls
as they will be available for omap1 only.
While at it, clean up the includes to group them like
they typically are grouped.
Signed-off-by: Tony Lindgren <tony@atomide.com>
There's no need to have these in plat/io.h.
While at it, clean up the includes to group them
like they typically are grouped.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Flag single_channel in struct omap2_mcspi_device_config is not used
by drivers/spi/spi-omap2-mcspi.c so we may remove it from include/plat/mcspi.h
and affected board files.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In an effort to clean up the old omapfb driver, this patch removes
HWA742 (the display chip used in N770) platform data. This can be done
as N770 is the only user of HWA742, and the platform data contains only
one field, te_connected, which we can just presume to be true in the
HWA742 driver.
This allows us to remove omapfb_set_ctrl_platform_data(), and the
mechanism to pass the platform data, in a later patch.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
OMAP SRAM can be used as video memory on OMAP1 and 2. However, there
usually is very little SRAM available, thus limiting its use, and no
board supported by the kernel currently uses it.
This patch removes the use of SRAM as video ram for the omapdss driver
to simplify memory handling.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
* lpc32xx/drivers: (566 commits)
ARM: LPC32xx: ADC support for mach-lpc32xx
Includes an update to Linux 3.3-rc4
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
N8x0's blizzard driver has been ported to new omapdss driver, so we can
now remove the old blizzard driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
commit 2fd149645e (ARM: OMAP2+: UART: Remove omap_uart_can_sleep and
add pm_qos) removed omap_uart_can_sleep and omap3_can_sleep, but not
their declarations. So remove those now.
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
[khilman@ti.com: minor changelog edits]
Signed-off-by: Kevin Hilman <khilman@ti.com>
Expose omap_device_{alloc, delete, register} so we can use them outside
of omap_device.c.
This approach allows users, which need to manipulate an archdata member
of a device before it is registered, to do so. This is also useful
for users who have their devices created very early so they can be used
at ->reserve() time to reserve CMA memory.
The immediate use case for this is to set the private iommu archdata
member, which binds a device to its associated iommu controller.
This way, generic code will be able to attach omap devices to their
iommus, without calling any omap-specific API.
With this in hand, we can further clean the existing mainline OMAP iommu
driver and its mainline users, and focus on generic IOMMU approaches
for future users (rpmsg/remoteproc and the upcoming generic DMA API).
This patch is still considered an interim solution until DT fully materializes
for omap; at that point, this functionality will be removed as DT will
take care of creating the devices and configuring them correctly.
Tested on OMAP4 with a generic rpmsg/remoteproc that doesn't use any
omap-specific IOMMU API anymore.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
arm_memblock_steal() is not suppose to be used outside ->reserve callback.
OMAP barrier errata code was using it outside reserve callback and hence
it was broken.
Move the allocation as part of ->reserve callback to fix the it.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a remoteproc driver for OMAP4, so we can boot the dual-M3 and
and DSP subsystems.
Use the omap_device_* API to control the hardware state, and utilize
the OMAP mailbox to interrupt the remote processor when a new message
is pending (the mailbox payload is used to tell it which virtqueue was
the message placed in).
Conversely, when an inbound mailbox message arrives, tell the remoteproc
core which virtqueue is triggered.
Later we will also use the mailbox payload to signal omap-specific
events like remote crashes (which will be used to trigger remoteproc
recovery) and power management transitions. At that point we will also
extend the remoteproc core to support this.
Based on (but now quite far from) work done by Fernando Guzman Lugo
<fernando.lugo@ti.com> and Hari Kanigeri <h-kanigeri2@ti.com>.
Designed with Brian Swetland <swetland@google.com>.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Brian Swetland <swetland@google.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
With the latest Sourcery G++ Lite 2011.03-41 and latest linaro
tool-chains OMAP2 only build breaks with below error.
arch/arm/mach-omap2/omap-smc.S: Assembler messages:
arch/arm/mach-omap2/omap-smc.S:30: Error: selected processor does not support ARM mode `smc #0'
arch/arm/mach-omap2/omap-smc.S:53: Error: selected processor does not support ARM mode `smc #0'
arch/arm/mach-omap2/omap-smc.S:61: Error: selected processor does not support ARM mode `smc #0'
arch/arm/mach-omap2/omap-smc.S:69: Error: selected processor does not support ARM mode `smc #0'
arch/arm/mach-omap2/omap-smc.S:77: Error: selected processor does not support ARM mode `smc #0'
make[1]: *** [arch/arm/mach-omap2/omap-smc.o] Error 1
OMAP2 devices doesn't have the security support but the security support
was getting built because of OMAP2PLUS. Don't build security code for
OMAP2 devices.
While at it, fix the secure-common line in the Makefile to use tabs
instead of spaces.
Reported-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The only bank->type (method) used in the OMAP GPIO driver is MPUIO type as they
need to be handled separately. Identify the same using a flag and remove all
METHOD_* macros.
mpuio_init() function is defined under #ifdefs. It is required only in case
of MPUIO bank type and only when PM operations are supported by it.
This is applicable only in case of OMAP16xx SoC's MPUIO GPIO bank type.
For all the other cases it is a dummy function. Hence clean up the same
and remove all the OMAP SoC specific #ifdefs.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Use regs->pinctrl field instead of using the macro OMAP1510_GPIO_PIN_CONTROL
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Getting rid of ifdefs within the function by adding register offset intctrl
and associating OMAPXXXX_GPIO_INT_CONTROL in respective SoC specific files.
Also, use wkup_status register consistently instead of referring to wakeup
clear and wakeup set register offsets. Get rid of cpu_is_xxxx checks in
set_gpio_trigger() using irqctrl.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
It is not required to use hard-coded offsets any more in context save and
restore functions and instead use the generic offsets which have been correctly
initialized during device registration.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
By adding level and edge detection register offsets and then initializing them
correctly according to OMAP versions during device registrations we can now remove
lot of revision checks in these functions.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Wakeup enable register offset initialized according to OMAP versions
during device registration. Use this to avoid version checks.
Starting with OMAP4, legacy registers should not be used in combination
with the updated regsiters. Use wkup_en register consistently for
all SoCs wherever applicable.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Remove cpu-is checks while enabling/disabling OMAP GPIO module during a gpio
request/free.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Non-wakeup GPIOs are available only in OMAP2. Avoid cpu_is checks by making
non_wakeup_gpios as part of pdata.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Modify omap_gpio_prepare_for_idle() & omap_gpio_resume_after_idle() functions
to handle save context & restore context respectively in the OMAP GPIO driver
itself instead of calling these functions from pm specific files.
For this, in gpio_prepare_for_idle(), call *_get_context_loss_count() and in
gpio_resume_after_idle() call it again. If the count is different, do restore
context.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
In omap3, save/restore context is implemented for GPIO banks 2-6 as GPIO bank1
is in wakeup domain. Instead of identifying bank's power domain by bank id,
use 'loses_context' flag which is filled by pwrdm_can_ever_lose_context()
during dev_init.
For getting the powerdomain pointer, omap_hwmod_get_pwrdm() is used.
omap_device_get_pwrdm() could not be used as the pwrdm information needs to be
filled in pdata, whereas omap_device_get_pwrdm() could be used only after
omap_device_build() call.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The gpio_bank_count is the count of number of GPIO devices in a SoC. Remove this
dependency from the driver by using list. Also remove the dependency on array of
pointers to gpio_bank struct of all GPIO devices.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
When this is the only content remaining in mach/system.h then the
whole file is removed.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-and-tested-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: David Brown <davidb@codeaurora.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
A significant part of the changes for these two platforms went into
power management, so they are split out into a separate branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=P4kO
-----END PGP SIGNATURE-----
Merge tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
power management changes for omap and imx
A significant part of the changes for these two platforms went into
power management, so they are split out into a separate branch.
* tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (65 commits)
ARM: imx6: remove __CPUINIT annotation from v7_invalidate_l1
ARM: imx6: fix v7_invalidate_l1 by adding I-Cache invalidation
ARM: imx6q: resume PL310 only when CACHE_L2X0 defined
ARM: imx6q: build pm code only when CONFIG_PM selected
ARM: mx5: use generic irq chip pm interface for pm functions on
ARM: omap: pass minimal SoC/board data for UART from dt
arm/dts: Add minimal device tree support for omap2420 and omap2430
omap-serial: Add minimal device tree support
omap-serial: Use default clock speed (48Mhz) if not specified
omap-serial: Get rid of all pdev->id usage
ARM: OMAP2+: hwmod: Add a new flag to handle hwmods left enabled at init
ARM: OMAP4: PRM: use PRCM interrupt handler
ARM: OMAP3: pm: use prcm chain handler
ARM: OMAP: hwmod: add support for selecting mpu_irq for each wakeup pad
ARM: OMAP2+: mux: add support for PAD wakeup interrupts
ARM: OMAP: PRCM: add suspend prepare / finish support
ARM: OMAP: PRCM: add support for chain interrupt handler
ARM: OMAP3/4: PRM: add functions to read pending IRQs, PRM barrier
ARM: OMAP2+: hwmod: Add API to enable IO ring wakeup
ARM: OMAP2+: mux: add wakeup-capable hwmod mux entries to dynamic list
...
Again, a lot of platforms have changes in here: pxa, samsung, omap,
at91, imx, ...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=vPhu
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Driver specific changes
Again, a lot of platforms have changes in here: pxa, samsung, omap,
at91, imx, ...
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
ARM: sa1100: clean up of the clock support
ARM: pxa: add dummy clock for sa1100-rtc
RTC: sa1100: support sa1100, pxa and mmp soc families
RTC: sa1100: remove redundant code of setting alarm
RTC: sa1100: Clean out ost register
Input: zylonite-wm97xx - replace IRQ_GPIO() with gpio_to_irq()
pcmcia: pxa: replace IRQ_GPIO() with gpio_to_irq()
ARM: EXYNOS: Modified files for SPI consolidation work
ARM: S5P64X0: Enable SDHCI support
ARM: S5P64X0: Add lookup of sdhci-s3c clocks using generic names
ARM: S5P64X0: Add HSMMC setup for host Controller
ARM: EXYNOS: Add USB OHCI support to ORIGEN board
USB: Add Samsung Exynos OHCI diver
ARM: EXYNOS: Add USB OHCI support to SMDKV310 board
ARM: EXYNOS: Add USB OHCI device
net: macb: fix build break with !CONFIG_OF
i2c: tegra: Support DVC controller in device tree
i2c: tegra: Add __devinit/exit to probe/remove
net/at91_ether: use gpio_is_valid for phy IRQ line
ARM: at91/net: add macb ethernet controller in 9g45/9g20 DT
...
This adds support for new features, and contains stuff from most
platforms. A number of these patches could have fit into other
branches, too, but were small enough not to cause too much
confusion here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=N2B4
-----END PGP SIGNATURE-----
Merge tag 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
New feature development
This adds support for new features, and contains stuff from most
platforms. A number of these patches could have fit into other
branches, too, but were small enough not to cause too much
confusion here.
* tag 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
mfd/db8500-prcmu: remove support for early silicon revisions
ARM: ux500: fix the smp_twd clock calculation
ARM: ux500: remove support for early silicon revisions
ARM: ux500: update register files
ARM: ux500: register DB5500 PMU dynamically
ARM: ux500: update ASIC detection for U5500
ARM: ux500: support DB8520
ARM: picoxcell: implement watchdog restart
ARM: OMAP3+: hwmod data: Add the default clockactivity for I2C
ARM: OMAP3: hwmod data: disable multiblock reads on MMC1/2 on OMAP34xx/35xx <= ES2.1
ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP4
ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP3
ARM: OMAP: hwmod data: Add support for AM35xx UART4/ttyO3
ARM: Orion: Remove address map info from all platform data structures
ARM: Orion: Get address map from plat-orion instead of via platform_data
ARM: Orion: mbus_dram_info consolidation
ARM: Orion: Consolidate the address map setup
ARM: Kirkwood: Add configuration for MPP12 as GPIO
ARM: Kirkwood: Recognize A1 revision of 6282 chip
ARM: ux500: update the MOP500 GPIO assignments
...
This adds and extends support for specific boards on a number of
ARM platforms: omap, imx, samsung, tegra, ...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=lYb/
-----END PGP SIGNATURE-----
Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Board-level changes
This adds and extends support for specific boards on a number of
ARM platforms: omap, imx, samsung, tegra, ...
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (49 commits)
Enable 32 bit flash support for iMX21ADS board
ARM: mx31pdk: Add MC13783 RTC support
iomux-mx25: configuration to support CSPI3 on CSI pins
MX1:apf9328: Add i2c support
mioa701: add newly available DoC G3 chip
arm/tegra: remove __initdata annotation from pinmux tables
arm/tegra: Use bus notifiers to trigger pinmux setup
arm/tegra: Refactor board-*-pinmux.c to share code
arm/tegra: Fix mistake in Trimslice's pinmux
arm/tegra: Rework Seaboard-vs-Ventana pinmux table
arm/tegra: Remove useless entries from ventana_pinmux[]
arm/tegra: PCIe: Remove include of mach/pinmux.h
arm/tegra: Harmony PCIe: Don't touch pinmux
arm/tegra: Add AUXDATA for tegra-pinmux and tegra-gpio
arm/tegra: Split Seaboard GPIO table to allow for Ventana
ARM: imx6q: generate imx6q dtb files
arm/imx6q: Rename Sabreauto to Armadillo2
arm/imx6q-sabrelite: add enet phy ksz9021rn fixup
arm/imx6: add imx6q sabrelite board support
dts/imx: rename uart labels to consistent with hw spec
...
This adds support for the new tegra30 SoC, as well as small
changes to support minor variations of existing omap SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=hp8k
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
SoC-level changes for tegra and omap
This adds support for the new tegra30 SoC, as well as small
changes to support minor variations of existing omap SoCs.
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
arm/tegra: Compile tegra_dt_init_irq only when CONFIG_OF
arm/tegra: Make MACH_TEGRA_DT depend on ARCH_TEGRA_2x_SOC
arm/tegra: Delete tegra_init_clock()
arm/tegra: Fix section mismatch errors in tegra30 pinmux
arm/tegra: Fix section mismatch errors in tegra20 pinmux
arm/tegra: refresh defconfig for tegra30
arm/tegra: add support for tegra30 based board cardhu
arm/tegra: implement support for tegra30
arm/tegra: pinmux tables and definitions for tegra30
arm/tegra: add new fields to struct tegra_pingroup_desc
arm/tegra: prepare pinmux code for multiple tegra variants
arm/tegra: rename tegra20 pinmux files
arm/tegra: generalize L2 cache initialization
arm/tegra: use PMC reset
arm/tegra: rename board-dt.c to board-dt-tegra20.c
arm/tegra: prepare early init for multiple tegra variants
arm/tegra: don't export clk_measure_input_freq
arm/tegra: prepare clock code for multiple tegra variants
arm/tegra: cleanup tegra20 support
arm/tegra: clk_get should not be fatal
...
Fix up trivial conflict in arch/arm/mach-tegra/board-dt-tegra20.c
Conflicts:
arch/arm/mach-imx/mach-imx6q.c
arch/arm/mach-omap2/board-ti8168evm.c
arch/arm/mach-s3c64xx/Kconfig
arch/arm/mach-tegra/Makefile
arch/arm/mach-tegra/board-dt-tegra20.c
arch/arm/mach-tegra/common.c
Lots of relatively simple conflicts between the board
changes and stuff from the arm tree. This pulls in
the resolution from the samsung/cleanup tree, so we
don't get conflicting merges.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
arch/arm/mach-mxs/include/mach/common.h
Pull in previous samsung conflict merges and do a trivial
merge of an mxs double-add conflict.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (53 commits)
Kconfig: acpi: Fix typo in comment.
misc latin1 to utf8 conversions
devres: Fix a typo in devm_kfree comment
btrfs: free-space-cache.c: remove extra semicolon.
fat: Spelling s/obsolate/obsolete/g
SCSI, pmcraid: Fix spelling error in a pmcraid_err() call
tools/power turbostat: update fields in manpage
mac80211: drop spelling fix
types.h: fix comment spelling for 'architectures'
typo fixes: aera -> area, exntension -> extension
devices.txt: Fix typo of 'VMware'.
sis900: Fix enum typo 'sis900_rx_bufer_status'
decompress_bunzip2: remove invalid vi modeline
treewide: Fix comment and string typo 'bufer'
hyper-v: Update MAINTAINERS
treewide: Fix typos in various parts of the kernel, and fix some comments.
clockevents: drop unknown Kconfig symbol GENERIC_CLOCKEVENTS_MIGR
gpio: Kconfig: drop unknown symbol 'CS5535_GPIO'
leds: Kconfig: Fix typo 'D2NET_V2'
sound: Kconfig: drop unknown symbol ARCH_CLPS7500
...
Fix up trivial conflicts in arch/powerpc/platforms/40x/Kconfig (some new
kconfig additions, close to removed commented-out old ones)
Remove the now empty arch_reset() from all the mach/system.h includes,
and remove its callsite. Remove arm_machine_restart() as this function
no longer does anything useful.
For samsung platforms, remove the include of mach/system-reset.h and
plat/system-reset.h from their respective mach/system.h headers as these
just define their arch_reset functions. As a result, the s3c2410 and
plat-samsung system-reset.h files are no longer referenced, so remove
these files entirely.
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Hook these platforms restart code into the new restart hook rather
than using arch_reset().
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* omap/hwmod:
ARM: OMAP3+: hwmod data: Add the default clockactivity for I2C
ARM: OMAP3: hwmod data: disable multiblock reads on MMC1/2 on OMAP34xx/35xx <= ES2.1
ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP4
ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP3
ARM: OMAP: hwmod data: Add support for AM35xx UART4/ttyO3
ARM: OMAP: hwmod data: fix the panic on Nokia RM-680 during boot
ARM: OMAP: hwmod data: fix iva and mailbox hwmods for OMAP 3
ARM: OMAP: rx51: fix USB
ARM: OMAP: mcbsp: Fix possible memory corruption
Don't use Amstrad Delta custom I/O functions once GPIO interface is
available for the underlying hardware.
While requesting and initializing GPIO pins used, also take care of one
extra pin KEYBRD_DATAOUT which, even if not used by the driver, belongs
to the device and affects its functioning.
Once done, move the driver initialization back to the device_initcall
level, reverting the temporary chane introduced with patch 1/7 "ARM:
OMAP1: ams-delta: register latch dependent devices later". That change
is no longer required once the driver takes care of registering used
GPIO pins, and it's better to initialize the device before others using
the latch2 based GPIO pins, otherwise a garbage is reported on boot,
perhaps due to random data already captured by the FIQ handler while the
keyboard related latch bits are written with random values during
initialization of those other latch2 dependent devices.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
[tony@atomide.com: renamed _gpios to ams_delta_gpios]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Don't use Amstrad Delta custom I/O functions any longer, use GPIO API
instead.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Don't use Amstrad Delta custom I/O functions for controlling the device,
use GPIO API instead.
While being at it, add missing gpio_free(AMS_DELTA_GPIO_PIN_NAND_RB).
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Cc: David Woodhouse <dwmw2@infradead.org>
Reviewed-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that the Amstrad Delta on-board latches have been converted to GPIO
devices, use the generic driver to control on-board LEDs which hang off
those latches.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Once ready, ams-delta specific device drivers currently calling custom
ams_delta_latch[12]_write() functions can be updated to call generic
gpio_set_value() instead, which will make them less platform dependent.
Even more, some custom ams-delta only drivers can perhaps be dropped
from the tree after converting selected ams-delta platform devices to
follow generic GPIO based device models.
The latch_gpios[] table is initially filled with all latch1 and latch2
GPIO pins in order to register and initialize them from the board file
until those are handled by respective existing device drivers (leds,
nand, lcd, serio, asoc, serial). That table will get almost empty after
the transision process is completed, holding only pins not used by any
drivers / connected to unused devices, in order to initialize them from
the board file for power saving purposes.
The new ams_delta_latch_write() function is a unified replacement for
those removed ams_delta_latch[12]_write(), and serves as a temporary
wrapper over gpio_set_value(), providing the old API for those not yet
updated device drivers, and will be removed after all custom drivers are
converted or replaced.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to detect the SoC revision early, but the SoC
feature detection can be done later on. In order to allow
further clean-up later on, this patch separates the SoC
revision check from the SoC feature check.
This patch doesn't change functionality or behavior of the code
execution; it barely cleans up the code and splits into SoC
specific implementation for Rev ID and feature detection.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
sched_clock() is yet another blocker on the road to the single
image. This patch implements an idea by Russell King:
http://www.spinics.net/lists/linux-omap/msg49561.html
Instead of asking the platform to implement both sched_clock()
itself and the rollover callback, simply register a read()
function, and let the ARM code care about sched_clock() itself,
the conversion to ns and the rollover. sched_clock() uses
this read() function as an indirection to the platform code.
If the platform doesn't provide a read(), the code falls back
to the jiffy counter (just like the default sched_clock).
This allow some simplifications and possibly some footprint gain
when multiple platforms are compiled in. Among the drawbacks,
the removal of the *_fixed_sched_clock optimization which could
negatively impact some platforms (sa1100, tegra, versatile
and omap).
Tested on 11MPCore, OMAP4 and Tegra.
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Colin Cross <ccross@android.com>
Cc: Erik Gilling <konkers@android.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: STEricsson <STEricsson_nomadik_linux@list.st.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Tested-by: Jamie Iles <jamie@jamieiles.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Krzysztof Halasa <khc@pm.waw.pl>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
An hwmod with a 'HWMOD_INIT_NO_IDLE' flag set, is left in
enabled state by the hwmod framework post the initial setup.
Once a real user of the device (a driver) tries to enable it
at a later point, the hwmod framework throws a WARN() about
the device being already in enabled state.
Fix this by introducing a new internal flag '_HWMOD_SKIP_ENABLE' to
identify such devices/hwmods. When the device/hwmod is requested to be
enabled (the first time) by its driver/user, nothing except the
mux-enable is needed. The mux data is board specific and is
unavailable during initial enable() of the device, done by the
framework as part of setup().
A good example of a such a device is an UART used as debug console.
The UART module needs to be kept enabled through the boot, until the
UART driver takes control of it, for debug prints to appear on
the console.
Acked-by: Kevin Hilman <khilman@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: use a flag rather than a state; updated commit message;
edited some documentation]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
By default all registered pads will trigger mpu_irqs[0]. Now there is
an API for selecting used mpu_irq on pad basis, which can be used to
trigger different irq handlers for different pads in the same hwmod.
Each pad that requires its interrupt to be re-routed this way must
have a separate call to omap_hwmod_pad_route_irq(hwmod, pad, irq).
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
[paul@pwsan.com: moved fn to omap_hwmod.c; separated fn from mux scan_wakeups
changes; added kerneldoc]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP mux now parses active wakeup events from pad registers and calls
corresponding hwmod ISRs once a wakeup is detected. This is
accomplished by registering an interrupt handler for PRCM IO event,
which is raised every time the HW detects wakeups.
[paul@pwsan.com: This patch is a merge of Govindraj R's "ARM: OMAP2+:
hwmod: Add API to check IO PAD wakeup status" patch, Tero Kristo's
"ARM: OMAP2+: mux: add support for PAD wakeup interrupts" patch, and
part of Tero's "ARM: OMAP: mux: add support for selecting mpu_irq for
each wakeup pad" patch.]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Govindraj.R <govindraj.raja@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
[paul@pwsan.com: reduced indentation level; renamed omap_hwmod function;
improved function documentation; modified to iterate only through dynamic
pads; modified to skip pads where idle mode doesn't enable wakeups; split
patches]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The ehci and ohci drivers does not use the APIs of the usbhs
core driver; the runtime pm APIs are used for clock
enable/disable. Since usbhs is parent platform device of the
ehci and ohci devices, the runtime apis indirectly uses the
usb hs core device as input parameter to for clock functions.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Reviewed-by: Partha Basak <parthab@india.ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add hwmod support to enable access to UART4 of the AM35xx series of
chips. The UART4 device referenced from the TRM will show up as ttyO3.
This was tested on an AM3505.
Signed-off-by: Kyle Manna <kyle.manna@fuel7.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Omap_uart_can_sleep function blocks system wide low power state until
uart is active remove this func and add qos requests to prevent
MPU from transitioning.
Keep qos request to default value which will allow MPU to transition
and while uart baud rate is available calculate the latency value
from the baudrate and use the same to hold constraint while uart clocks
are enabled, and if uart is auto-idled the constraint is updated with
default constraint value allowing MPU to transition.
Qos requests are blocking notifier calls so put these requests to
work queue, also the driver uses irq_safe version of runtime API's
and callbacks can be called in interrupt disabled context.
So to avoid warn on slow path warning while using qos update
API's from runtime callbacks use the qos_work_queue.
During bootup the runtime_resume call backs might not be called and runtime
callback gets called only after uart is idled by setting the autosuspend
timeout. So qos_request from runtime resume callback might not activated during
boot if uart baudrate is calculated during bootup for console uart, so schedule
the qos_work queue once we calc_latency while configuring the uart port.
Flush and complete any pending qos jobs in work queue while suspending.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
When using DMA there are two timeouts defined. The first timeout,
rx_timeout, is really a polling rate in which software polls the
DMA status to see if the DMA has finished. This is necessary for
the RX side because we do not know how much data we will receive.
The secound timeout, RX_TIMEOUT, is a timeout after which the
DMA will be stopped if no more data is received. To make this
clearer, rename rx_timeout as rx_poll_rate and rename the
function serial_omap_rx_timeout() to serial_omap_rxdma_poll().
The OMAP-Serial driver defines an RX_TIMEOUT of 3 seconds that is
used to indicate when the DMA for UART can be stopped if no more
data is received. The value is a global definition that is applied
to all instances of the UART.
Each UART may be used for a different purpose and so the timeout
required may differ. Make this value configurable for each UART so
that this value can be optimised for power savings.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
The following UART parameters are defined within the UART driver:
1). Whether the UART uses DMA (dma_enabled), by default set to 0
2). The size of dma buffer (set to 4096 bytes)
3). The time after which the dma should stop if no more data is received.
4). The auto suspend delay that will be passed for pm_runtime_autosuspend
where uart will be disabled after timeout
Different UARTs may be used for different purpose such as the console,
for interfacing bluetooth chip, for interfacing to a modem chip, etc.
Therefore, it is necessary to be able to customize the above settings
for a given board on a per UART basis.
This change allows these parameters to be configured from the board file
and allows the parameters to be configured for each UART independently.
If a board does not define its own custom parameters for the UARTs, then
use the default parameters in the structure "omap_serial_default_info".
The default parameters are defined to be the same as the current settings
in the UART driver to avoid breaking the UART for any cuurnelty supported
boards. By default, make all boards use the default UART parameters.
Signed-off-by: Deepak K <deepak.k@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
From the runtime callbacks enable hwmod wakeups for uart which will
internally enable io-pad wakeups for uarts if they have rx-pad pins
set as wakeup capabale.
Use the io-ring wakeup mechanism after uart clock gating and leave
the PM_WKST set for uart to default reset values cleanup the
code in serial.c which was handling PM_WKST reg.
Irq_chaing(PRM_DRIVER) is used to wakeup uart after uart clocks are gated
using pad wakeup mechanism.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
Move the errata handling mechanism from serial.c to omap-serial file
and utilise the same func in driver file.
Errata i202, i291 are moved to be handled with omap-serial
Moving the errata macro from serial.c file to driver header file
as from on errata will be handled in driver file itself.
Corrected errata id from chapter reference 2.15 to errata id i291.
Removed errata and dma_enabled fields from omap_uart_state struct
as they are no more needed with errata handling done within omap-serial.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Avoid unconditional context restore every time we gate uart
clocks. Check whether context loss happened based on which
we can context restore uart regs from uart_port structure.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
Remove the uart reset function which is configuring the
TX empty irq which can now be handled within omap-serial driver.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add missing uart regs to uart_port structure which can be used in
context restore. Store dll, dlh, mdr1, scr, efr, lcr, mcr reg values
into uart_port structure while configuring individual port in termios
function.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
The mapbase (start_address), membase(io_remap cookie) part of
pdata struct omap_uart_port_info are removed as this should be
derived within driver.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
Currently we use a shared irq handler to identify uart activity and then
trigger a timer. By default the timeout value is zero and can be set or
modified from sysfs. If there was no uart activity for the period set
through sysfs, the timer will expire and call timer handler this will
set a flag can_sleep using which decision to gate uart clocks can be taken.
Since the clock gating mechanism is outside the uart driver, we currently
use this mechanism. In preparation to runtime implementation for omap-serial
driver we can cleanup this mechanism and use runtime API's to gate uart clocks.
Removes the following:
* timer related info from local uart_state struct
* the code used to set timeout value from sysfs.
* irqflags used to set shared irq handler.
* un-used function omap_uart_check_wakeup.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
In preparation to UART runtime conversion remove uart specific calls
from pm24xx/34xx files and their definition from serial.c
These func calls will no more be used with upcoming uart runtime design.
1.) omap_uart_prepare_suspend :- can be taken care with driver suspend hooks.
2.) omap_uart_enable_irqs :- Used to enable/disable uart irq's in suspend
path from PM code, this is removed as same is handled by
uart_suspend_port/uart_resume_port in omap-serial driver which will
do an port_shutdown on suspend freeing irq and port_startup on resume
enabling back irq.
3.) Remove prepare_idle/resume_idle calls used to gate uart clocks.
UART clocks can be gated within driver using runtime funcs
and be woken up using irq_chaining from omap_prm driver.
4.) Remove console_locking from idle path as clock gating is done withing
driver itself with runtime API. Remove is_suspending check used to acquire
console_lock.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Adding ti81xx_musb_phy_power() which will be used by musb driver through
its function pointer in board_data.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds minimal support and build configuration for TI8148 EVM. Also
adds support for low level debugging on UART1 console on the EVM.
Note that existing TI8168 EVM file (board-ti8168evm.c) is updated with machine
info for TI8148 EVM.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds cpu type, macros for identification of TI814X device.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
[tony@atomide.com: left out CK_TI814X for now]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates existing macros, functions used for TI816X, to enable
addition of other SoCs belonging to TI81XX family (e.g., TI814X).
The approach taken is to use TI81XX/ti81xx for code/data going to be common
across all TI81XX devices.
cpu_is_ti81xx() is introduced to handle code common across TI81XX devices.
In addition, ti8168_evm_map_io() is now replaced with ti81xx_map_io() and moved
in mach-omap2/common.c as same will be used for TI814X and is not board
specific.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
allow for the omap4430 es2.3 revision to be recognized in the
omap4_check_revision() function.
most aspects of all omap4430 es2.x versions are identical, however
a number of small variations such as default pullup or pulldown
resistor configurations vary between revisions.
detailed information on silicon errata for omap4430 revisions can
be found at http://focus.ti.com/pdfs/wtbu/swpz009D.pdf
Signed-off-by: David Anders <x0132446@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates the common machine specific source files for
support for AM33XX/AM335x with cpu type, macros for identification of
AM33XX/AM335X device.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
[tony@atomide.com: updated for map_io and common.h changes, dropped CK_AM33XX]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates the common platform files with AM335X device
support (AM33XX family).
The approach taken in this patch is,
AM33XX device will be considered as OMAP3 variant, and a separate
SoC class created for AM33XX family of devices with a subclass type
for AM335X device, which is newly added device in the family.
This means, cpu_is_omap34xx(), cpu_is_am33xx() and cpu_is_am335x()
checks will return success on AM335X device.
A kernel config option CONFIG_SOC_OMAPAM33XX is added under OMAP3
to include support for AM33XX build.
Also, cpu_mask and RATE_IN_XXX flags have crossed 8 bit hence
struct clksel_rate.flags, struct prcm_config.flags and cpu_mask
are changed to u16 from u8.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Hemant Pedanekar <hemantp@ti.com>
[tony@atomide.com: left out CK_AM33XX for now]
Signed-off-by: Tony Lindgren <tony@atomide.com>
For still better multi-OMAP1 support, expand omap1_rate_table with flags
for different SoC types and match them while selecting clock rates. The
idea is stolen from current omap24xx clock rate selection algorithm.
Since clkdev platform flag definitions are reused here, those had to be
expanded with one extra entry for OMAP1710 subtype, as this is the only
SoC for which we allow selection of the highest, 216 MHz rate.
Once done, remove no longer needed clock rate configure time options.
Tested on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pm_caps field to omap2_hsmmc_info and omap_mmc_slot_data
structs, so we will be able to indicate mmc pm capabilities
in the board file.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On OMAP4 SOC, intecronnects has many write buffers in the async bridges
and they need to be drained before CPU enters into standby state.
Patch 'OMAP4: PM: Add CPUX OFF mode support' added CPU PM support
but OMAP errata i688 (Async Bridge Corruption) needs to be taken
care to avoid issues like system freeze, CPU deadlocks, random
crashes with register accesses, synchronisation loss on initiators
operating on both interconnect port simultaneously.
As per the errata, if a data is stalled inside asynchronous bridge
because of back pressure, it may be accepted multiple times, creating
pointer misalignment that will corrupt next transfers on that data
path until next reset of the system (No recovery procedure once
the issue is hit, the path remains consistently broken).
Async bridge can be found on path between MPU to EMIF and
MPU to L3 interconnect. This situation can happen only when the
idle is initiated by a Master Request Disconnection (which is
trigged by software when executing WFI on CPU).
The work-around for this errata needs all the initiators
connected through async bridge must ensure that data path
is properly drained before issuing WFI. This condition will be
met if one Strongly ordered access is performed to the
target right before executing the WFI. In MPU case, L3 T2ASYNC
FIFO and DDR T2ASYNC FIFO needs to be drained. IO barrier ensure
that there is no synchronisation loss on initiators operating
on both interconnect port simultaneously.
Thanks to Russell for a tip to conver assembly function to
C fuction there by reducing 40 odd lines of code from the patch.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Richard Woodruff <r-woodruff2@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Allocate the memory to save secure ram context which needs
to be done when MPU is hitting OFF mode.
The ROM code expects a physical address to this memory
and hence use memblock APIs to reserve this memory as part
of .reserve() callback. Maximum size as per secure RAM requirements
is allocated.
To keep omap1 build working, omap-secure.h file is created
under plat-omap directory.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds SAR RAM support on OMAP4430. SAR RAM used to save
and restore the HW context in low power modes.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Eliminate the public omap_find_iommu_device() method, and don't
expect clients to provide the omap_iommu handle anymore.
Instead, OMAP's iommu driver now utilizes dev_archdata's private iommu
extension to be able to access the required iommu information.
This way OMAP IOMMU users are now able to use the generic IOMMU API without
having to call any omap-specific binding method.
Update omap3isp appropriately.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Hiroshi Doyu <hdoyu@nvidia.com>
Declare an omap iommu private struct, which binds an iommu user
to its iommu device. This struct should be placed at the iommu user's
dev_archdata so generic IOMMU API can be used without having to
utilize omap-specific plumbing anymore.
While at it, provide an accessor method to ease the retrieval of the
omap_iommu handle from a user device.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Hiroshi Doyu <hdoyu@nvidia.com>
The below patch fixes some typos in various parts of the kernel, as well as fixes some comments.
Please let me know if I missed anything, and I will try to get it changed and resent.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Conflicts:
arch/arm/mach-omap2/board-4430sdp.c
arch/arm/mach-omap2/board-omap4panda.c
arch/arm/mach-omap2/include/mach/omap4-common.h
arch/arm/plat-omap/include/plat/irqs.h
The changes to omap4-common.h were moved to arch/arm/mach-omap2/common.h
and the other trivial conflicts resolved. The now empty ifdef in irqs.h
was also eliminated.
A generic version should replace this later.
As io.c has become nearly empty, omap_init_consistent_dma_size() is moved
into common.c so that io.c can be removed entirely.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Kevin Hilman <khilman@ti.com>
As suggested by Russell King - ARM Linux <linux@arm.linux.org.uk>,
there's no need to keep local prototypes in non-local headers.
Add mach-omap1/common.h and mach-omap2/common.h and move the
local prototypes there from plat/common.h and mach/omap4-common.h.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide the OMAP2/3 IRQ code with low level handlers that can be used
by platforms using CONFIG_MULTI_IRQ_HANDLER. Though the handlers are
written in C, the compiled code looks very similar to its assembly
counterpart (at least with my gcc 4.4.1).
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Without this patch we get the following error:
arch/arm/mach-omap2/clkt_dpll.c: In function '_dpll_test_fint':
arch/arm/mach-omap2/clkt_dpll.c:98: error: 'struct dpll_data' has no member named 'flags'
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds a custom DSS reset function used on OMAPs from OMAP2
forward.
The function doesn't actually do a reset, it only waits for the reset to
complete. The reason for this is that on OMAP4 there is no possibility
to do a SW reset, and on OMAP2/3 doing a SW reset for dss_core resets
all the other DSS modules also, thus breaking the HWMOD model where
every DSS module is handled independently.
This fixes the problem with DSS reset on OMAP4, caused by the fact that
because there's no SW reset for dss_core on OMAP4, the HWMOD framework
doesn't try to reset dss_core and thus the DSS clocks were never enabled
at the same time. This causes causes the HWMOD reset to fail for
dss_dispc and dss_rfbi.
The common reset function will also allow us to fix another problem in
the future: before doing a reset we need to disable DSS outputs, which
are in some cases enabled by the bootloader, as otherwise DSS HW seems
to get more or less stuck, requiring a power reset to recover.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[paul@pwsan.com: modified to build arch/arm/mach-omap2/display.o
unconditionally to avoid an error when !CONFIG_OMAP2_DSS]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
There is no use for omap-alsa.h and board-palmz71.c doesn't need it either.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
get_context_loss_count functions return context loss count as u32, and
zero means an error. However, zero is also returned when context has
never been lost and could also be returned when the context loss count
has wrapped and goes to zero.
Change the functions to return an int, with negative value meaning an
error.
OMAP HSMMC code uses omap_pm_get_dev_context_loss_count(), but as the
hsmmc code handles the returned value as an int, with negative value
meaning an error, this patch actually fixes hsmmc code also.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
[tony@atomide.com: updated to fix a warning with recent dmtimer changes]
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'next/cleanup2' of git://git.linaro.org/people/arnd/arm-soc: (31 commits)
ARM: OMAP: Warn if omap_ioremap is called before SoC detection
ARM: OMAP: Move set_globals initialization to happen in init_early
ARM: OMAP: Map SRAM later on with ioremap_exec()
ARM: OMAP: Remove calls to SRAM allocations for framebuffer
ARM: OMAP: Avoid cpu_is_omapxxxx usage until map_io is done
ARM: OMAP1: Use generic map_io, init_early and init_irq
arm/dts: OMAP3+: Add mpu, dsp and iva nodes
arm/dts: OMAP4: Add a main ocp entry bound to l3-noc driver
ARM: OMAP2+: l3-noc: Add support for device-tree
ARM: OMAP2+: board-generic: Add i2c static init
ARM: OMAP2+: board-generic: Add DT support to generic board
arm/dts: Add support for OMAP3 Beagle board
arm/dts: Add initial device tree support for OMAP3 SoC
arm/dts: Add support for OMAP4 SDP board
arm/dts: Add support for OMAP4 PandaBoard
arm/dts: Add initial device tree support for OMAP4 SoC
ARM: OMAP: omap_device: Add a method to build an omap_device from a DT node
ARM: OMAP: omap_device: Add omap_device_[alloc|delete] for DT integration
of: Add helpers to get one string in multiple strings property
ARM: OMAP2+: devices: Remove all omap_device_pm_latency structures
...
Fix up trivial header file conflicts in arch/arm/mach-omap2/board-generic.c
* 'next/pm' of git://git.linaro.org/people/arnd/arm-soc: (66 commits)
ARM: CSR: PM: use outer_resume to resume L2 cache
ARM: CSR: call l2x0_of_init to init L2 cache of SiRFprimaII
ARM: OMAP: voltage: voltage layer present, even when CONFIG_PM=n
ARM: CSR: PM: add sleep entry for SiRFprimaII
ARM: CSR: PM: save/restore irq status in suspend cycle
ARM: CSR: PM: save/restore timer status in suspend cycle
OMAP4: PM: TWL6030: add cmd register
OMAP4: PM: TWL6030: fix ON/RET/OFF voltages
OMAP4: PM: TWL6030: address 0V conversions
OMAP4: PM: TWL6030: fix uv to voltage for >0x39
OMAP4: PM: TWL6030: fix voltage conversion formula
omap: voltage: add a stub header file for external/regulator use
OMAP2+: VC: more registers are per-channel starting with OMAP5
OMAP3+: voltage: update nominal voltage in voltdm_scale() not VC post-scale
OMAP3+: voltage: rename omap_voltage_get_nom_volt -> voltdm_get_voltage
OMAP3+: voltdm: final removal of omap_vdd_info
OMAP3+: voltage: move/rename curr_volt from vdd_info into struct voltagedomain
OMAP3+: voltage: rename scale and reset functions using voltdm_ prefix
OMAP3+: VP: combine setting init voltage into common function
OMAP3+: VP: remove unused omap_vp_get_curr_volt()
...
Fix up trivial conflict in arch/arm/mach-prima2/l2x0.c (code removal vs
edit)
Paul Walmsley
Kishon Vijay Abraham I
Tarun Kanti DebBarma
Vaibhav Hiremath
Tony Lindgren
Arnd Bergmann
Paul Bolle
Omar Ramirez Luna
Kevin Hilman
Jon Hunter
Afzal Mohammed
Linus Torvalds
J Keerthy
Ivan Djelic
Olof Johansson
Chris Lalancette
R Sricharan
Greg Kroah-Hartman
Govindraj.R
Fernando Guzman Lugo
Balaji T K
Florian Tobias Schandinat
Felipe Balbi
Rob Herring
Grant Likely
Peter Ujfalusi
Kukjin Kim
Tomi Valkeinen
Vaibhav Bedia
Benoit Cousson
Shweta Gulati
Janusz Krzysztofik
Aaro Koskinen
Jarkko Nikula
NeilBrown
Ohad Ben-Cohen
Santosh Shilimkar
Charulatha V
Nicolas Pitre
Russell King
Marc Zyngier
Rajendra Nayak
Tero Kristo
Keshava Munegowda
Kyle Manna
Deepak K
Ajay Kumar Gupta
Hemant Pedanekar
Leonid Iziumtsev
David Anders
Eliad Peller
Joerg Roedel
Justin P. Mattock